Abstract
Ultrashort pulse laser, capable of varying pulse duration between 210 fs and 10 ps and producing a burst of pulses with an intra-burst pulse repetition rate of 64.5 MHz (time distance between pulses 15.5 ns), was used to investigate the ablation efficiency of the copper. The study on ablation efficiency was done for various numbers of pulses per burst between 1 and 40. The increase in the ablation efficiency by 20% for 3 pulses per burst compared to a non-burst regime was observed. The comparison was made between the beam-size optimised regimes. Therefore, the real advantage of the burst regime was demonstrated. To the best of our knowledge, we report the highest laser milling ablation efficiency of copper of 4.84 µm3/µJ by ultrashort pulses at ~1 µm optical wavelength.
Similar content being viewed by others
Introduction
Ultrafast laser pulses are already widely used in material processing due to high flexibility and precision, but for competitive industry the processing throughput must always grow1. Recently, a lot of interest was shown to the studies of laser burst mode processing. One of the most successful studies demonstrated that bursts of high repetition rate pulses could increase ablation efficiency by introducing ablation-cooled material removal2. The study reveals that the ablation-cooled regime for copper starts somewhere between the intra-burst pulse repetition rate of 27 MHz and 108 MHz. The burst regime was also employed to enhance the laser modification efficiency of the transparent materials via accumulation effects3. The purpose of our work was to investigate the real advantage of the burst regime by comparing the beam-size optimised single-pulse regime with the beam-size optimised multiple-pulse burst regime, which was never previously demonstrated. The optimisation was done by increasing the spot size to find the maximum ablation efficiency for various pulse numbers per burst and different pulse durations as described in4. The idea of the optimal fluence for the highest ablation efficiency was proposed in5 and experimentally proven in6, where groove ablation was investigated. Studies of the ablation efficiency by changing the pulse energy was examined for various materials like metals7,8,9, semiconductors10,11, dielectrics12 and biological tissues13. When ablation optimisation is done by changing the size of the beam, the ablation rate (volume of the material removed per unit of time) and ablation efficiency (volume of the material removed with a unit of energy) are optimised together. The ultrafast Tunable Acoustic Gradient-Index lens was used to increase the micro-machining efficiency by changing the laser spot size14.
In this study, we have used a solid-state laser radiating at the 1030 nm wavelength and producing bursts of pulses with the intra-burst pulse repetition rate of 64.5 MHz. The increase up to 20% in the ablation efficiency for 3 pulses per burst compared to a non-burst regime was observed for all 12 tested pulse durations. The similar increase of copper ablation efficiency for the 3 pulses per burst regime compared to a single pulse regime was demonstrated by the pulse energy optimisation at a fixed beam size and reached improvement of 13%8 and 15%15. We demonstrate that further increase, leading to the highest ever published laser milling ablation efficiency, can be done by the beam-size-optimisation. The maximum ablation efficiency of 4.8 µm3/µJ and ablation rate of 0.18 mm3/s (10.5 mm3/min) was obtained, with the average optical power of 36 W, 3 pulses per burst and 10 ps pulse duration. In our best knowledge, the highest reported value of laser milling ablation efficiency for copper by ultrashort pulse laser emitting at ~1 µm optical wavelength, did not exceed <3 µm3/µJ8,10,15,16. The quality of processed surface at the optimal processing parameters for the highest ablation efficiency was evaluated by measuring the surface roughness Ra, and it was 0.4 µm. The optimal processing parameters were used for laser milling of complex 3D surfaces.
Materials and Methods
Experimental setup
A solid-state laser (Carbide, Light Conversion) with a variable pulse duration in the range of 210 fs–10 ps and radiating at the light wavelength of λ = 1030 nm was used in the experiments. The laser had a possibility to emit a burst of a certain number of pulses from 1 (single pulse regime) to 40. The intra-burst pulse repetition rate was 64.5 MHz, corresponding to the time distance between sequential pulses of 15.5 ns (Fig. 1) The burst repetition rate was always fixed at 300 kHz. An average optical power on the sample surface was 36 W. A galvanometer scanner (Intelliscan 14, Scanlab) and F-theta lens with a focal distance of 100 mm were used to scan and focus the laser beam.
Ablation efficiency characterisation
Rectangular cavities with dimensions of 2 × 1 mm2 were engraved into a copper target. Multiple layer scanning was applied to increase the depth and measurement accuracy of cavities profiles. The largest cavity depth reached <80 µm. Cavity depth never exceeded the Rayleigh length of the laser beam. A linear dependence of the cavity depth versus the number of pulses applied was maintained during the experiment. Therefore, the ablation saturation effects were completely avoided, and reliable data were collected for all investigated regimes17. The beam scanning speed of 1 m/s and the distance between scanned lines (hatch) of 10 µm were always constant. The maximum laser power at 300 kHz was exploited in the ablation efficiency measurements. However, the laser fluence was varied by changing the spot size of the focused beam. By defocusing the laser beam from 0 mm (focus position) to 5.5 mm, the beam spot radius w on the sample surface was varied from 25.9 µm to 82.3 µm, respectively. The ablation efficiencies dependence on laser fluence was investigated for 10 different numbers of pulses in the burst: 1 (single-pulse regime), 2, 3, 4, 5, 6, 10, 20, 30, 40. These experiments were repeated for 12 different pulse durations: 210, 300, 400, 500, 600, 700, 800, 900, 1000, 2000, 5000, 10000 fs. In total, 1320 combinations of parameters (11 beam radii, 10 numbers of pulses per burst, 12 pulse durations) were tested, and 1320 cavities were milled.
Laser beam characterisation
Beam radius at various z positions was measured by a well-known D2 technique, described in18. Some of the measurement results are depicted in Fig. 2a. The relationship between damage diameter squared D2 and pulse energy Ep is described by18:
Eth – damage threshold energy. Therefore, at each z position, beam radii are extracted from the linear fit, as shown in Fig. 2b. The Gaussian-beam propagation equation19
where w0 is the laser spot size in focus, z0 is the focal position of the beam, λ = 1030 nm is the wavelength of irradiation. The Eq. (2) was used to fit the experimental data, and beam quality parameter M2 = 1.09 ± 0.02 was retrieved, which coincidence well with the value provided by the laser manufacturer.
Sample characterisation
Copper samples with dimensions of 50 × 50 × 5 mm3, purity of 99.9% and surface roughness of Ra < 0.1 µm were used as a target material for laser ablation. Copper is a test metal widely used for the study of laser ablation characteristics. For sample visualisation, scanning electron microscope (SEM) (JSM-6490LV, JEOL) was used. Stylus profiler (Dektak 150, Veeco) was used to measure depths of the cavities (Fig. 3). The surface roughness Ra and cavity volume were extracted from the cavities profile measurements.
Results and Discussion
The number of pulses per burst
To find the real advantage of the burst regime, the beam size optimisation was introduced for each experiment with various numbers of pulses per burst. In general, a highly defocused laser beam should not remove the material from the target due to laser fluence being lower than the ablation threshold of the material. The peak pulse fluence F0 depends on the beam radius w0 as:
where Ep is the pulse energy of the individual pulses in the burst, not the energy of the whole burst. Similarly, peak pulse fluence refers to the fluence of the individual pulses in the burst. For the burst fluence, (3) should be multiplied by the number of pulses in the burst. Infinitely tightly focused laser beam would make a deep and narrow crater, but the volume of the removed material would maintain infinitely small. Therefore, the optimum point of the laser beam size for specific pulse energy, where the maximum volume of the material is removed, exists. This optimisation method allows finding at the same time, the highest ablation efficiency and highest ablation rate point for any combination of the processing parameters4,17. The mistake would be to optimise pulse energy to find the highest ablation efficiency and optimum fluence than use maximum average power from the laser to reach the highest ablation rate by increasing the spot size to maintain the optimum fluence. When the beam size on the sample surface is increased, the ablation threshold Fth is decreased due to the possibility for laser radiation to hit a defect20,21, meaning that the optimum fluence Fopt may shift down. According to the ablation model, the optimal and threshold fluences are interrelated6:
The ablation efficiency has maxima at specific peak pulse fluence values. Experimentally it was found that the fluence values were dependent on the pulse number in the burst, but the pulse duration effect was less pronounced (see Fig. 4). The highest efficiency was measured for 3 pulses in the burst for all pulse durations. The increase in ablation efficiency compared with the single-pulse regime was from 11 to 20%, depending on the laser pulse duration used in experiments.
The maximum ablation efficiencies at the optimum fluences were extracted from Fig. 4 and plotted versus the number of pulses in the burst (Fig. 5). The maximum ablation efficiency decreased sharply when 2 pulses in the burst were used, then suddenly grown up and exceeded the value of the single-pulse regime for 3 pulses per burst. For 4 pulses per burst, the maximum efficiency decreased again, for 5 pulses – marginally increased, later it decreased gradually. This behaviour was observed for all tested pulse durations. The explanation of the efficiency decrease for 2 pulses per burst and increase for 3 pulses per burst is discussed in15. The time interval after the first pulse hit the target material is as long as 15.5 ns and is not sufficient for ejected particles to fly away from the interaction area. As shown by the molecular dynamics simulation, particles ejected during laser ablation can move at ~2 km/s speed22, which results in a 31 µm distance after 15.5 ns. Therefore, the second pulse is attenuated by particle plume. Also, ablation products made by the first pulse are forced by the second pulse to be redeposited back on substrate23, which could lead to low ablation efficiency by the second laser pulse. Redeposited hot particles contribute to the ablation efficiency increase as hot material has a higher absorptance24. The calorimetric measurement for copper showed that absorptance for 3 pulses per burst is almost twice as high as a one for the single pulse regime10. Also, the higher temperature of the interaction area might improve the ablation efficiency as the energy required to evaporate the material by the third pulse is lower25. The advantage of using the burst regime in the case of ablation efficiency was only visible for the regime with 3 pulses in the burst. For all other pulse numbers in the burst, the efficiency was lower compared to the single-pulse regime.
The highest ablation efficiency of 4.8 µm3/µJ and ablation rate of 10.5 mm3/min was reached in this work for 3 pulses per burst and 10 ps pulse duration regime at the 120 µJ burst energy. To our best knowledge, this is the highest laser milling ablation efficiency obtained for copper material by ultrashort pulse lasers emitting at ~1 µm optical wavelength. The higher ablation efficiency of ~7.6 µm3/µJ was demonstrated only by punching (ablation of a crater) with the ablation-cooled material removal (burst of pulses N = 800, intra-burst repetition rate of fP = 3456 MHz, burst repetition rate fB = 1 kHz, laser wavelength λ = 1040 nm, pulse duration of τ = 1 ps)2. Due to the low burst repetition rate of fB = 1 kHz, the ablation rate was only 0.03 mm3/min. As discussed in26, the laser milling has lower ablation efficiency compared to the laser punching efficiency of ~10 times due to differences in heat accumulation and melt flow in two machining approaches. The ablation-cooling regime was also investigated for copper with a high-power laser (burst repetition rate of fB = 200 kHz, burst energy EB = 93 µJ). In this case, the ablation rate as high as 6 mm3/min was reached for punching with N = 560 pulses in the burst, with fP = 1600 MHz intra-burst repetition rate27. However, it was still 40% lower than the ablation rate for laser milling achieved in our study. In paper28, the punching-mode processing in the burst regime was utilised for copper and efficiency reached ~3.2 µm3/µJ by N = 5, fB = 50 MHz, λ = 1064 nm, τ = 10 ps. A lot of work in the pulse energy optimisation for bursts was done by Neuenschwander et al., who found the maximum milling ablation efficiency for copper of 2.6 µm3/µJ8,15,29 or 2.9 µm3/µJ7 for λ = 1064 nm and λ = 1030 nm which is more than 40% lower than the ablation efficiency achieved in our study. The beam-size-optimised single-pulse regimes showed the milling ablation efficiency of copper as high as 2.5 µm3/µJ for λ = 1064 nm and τ = 10 ps4,17.
Pulse duration
The maximum ablation efficiencies at the optimum fluences were extracted from Fig. 4 and graph versus pulse duration is plotted in Fig. 6. The increase in the maximum ablation efficiency at longer pulse durations was observed for all number of pulses in the burst. For 3 pulses per burst, the maximum ablation efficiency was 32% higher at the 10 ps pulse duration compared to 210 fs.
Surface roughness
The lowest cavity surface roughness was obnained in the same range of pulse fluences (1–3 J/cm2) as the highest ablation efficiency (see Fig. 7). This means that two highly important micro-machining characteristics: the ablation efficiency and surface quality can be optimised simultaneously. For the single-pulse regime, the surface roughness was always higher compared to the burst mode – another advantage of the burst regime.
The surface roughness at the optimum laser fluence Fopt for the highest ablation efficiency was extracted from Fig. 7 and plotted versus the number of pulses per burst (Fig. 8). The surface roughness as small as 0.4 µm was achieved for the most efficient regime of 3 pulses per burst and pulse duration of 10 ps.
Laser milling of complex 3D cavities
The burst mode micro-machining quality was tested by milling complex 3D cavities (Fig. 9). The 3D micro-machining was realised using a layer-by-layer removal technique starting from the top of the sample. The distance between the focusing lens and sample surface was adjusted after each layer removal to maintain the optimal beam width on the ablated surface (see Fig. 9b). The most efficient 3 pulses per burst regime was selected, and the pulse duration was set to 10 ps. High-quality complex 3D cavities were laser milled. No side effects or melting was seen for longer pulses. Pulses of 10 ps length were short enough to minimise melt formation on the copper surface, which coincidence well with electron-ion thermalisation time in copper30. The bottom of the cavities was smooth, with no bumps or unwanted parasitic structure formation, which could ruin the aesthetic appearance of the cavities (see Fig. 9c).
Conclusions
The study of copper laser ablation by pulses of 64.5 MHz intra-burst pulse repetition rate revealed that, in the best case, the ablation efficiency could be improved by 20% compared to the single-pulse regime for the beam-size-optimised regimes. All other numbers of pulses per burst demonstrated lower ablation efficiency. To our best knowledge, the beam-size-optimised, 3 pulses per burst processing let us reach the highest ever published laser milling ablation efficiency of copper by ultrashort pulses −4.8 µm3/µJ. Another advantage of the burst mode compared to the single-pulse regime ablation was lower surface roughness of the bottom of the ablated cavities. The lowest surface roughness achieved by the single-pulse regime was several times higher than that measured for the burst mode. In the range of pulse duration between 210 fs and 10 ps, the ablation efficiency increased by 32% for longer pulses, and micro-machining quality improved. In conclusion, the usage of bursts of pulses for laser micro-processing of copper is advantageous only when 3 pulses per burst are used – the ablation efficiency and quality are increased compared to the single-pulse regime.
References
Malinauskas, M. et al. Ultrafast laser processing of materials: from science to industry. Light Sci. Appl. 5, e16133 (2016).
Kerse, C. et al. Ablation-cooled material removal with ultrafast bursts of pulses. Nature 537, 84–88 (2016).
Okhrimchuk, A., Fedotov, S., Glebov, I., Sigaev, V. & Kazansky, P. Single shot laser writing with sub-nanosecond and nanosecond bursts of femtosecond pulses. Sci. Rep. 7, 16563 (2017).
Žemaitis, A., Gaidys, M., Gečys, P., Račiukaitis, G. & Gedvilas, M. Rapid high-quality 3D micro-machining by optimised efficient ultrashort laser ablation. Opt. Lasers Eng. 114, 83–89 (2019).
Furmanski, J., Rubenchik, A. M., Shirk, M. D. & Stuart, B. C. Deterministic processing of alumina with ultrashort laser pulses. J. Appl. Phys. 102, 073112-1 (2007).
Račiukaitis, G., Brikas, M., Gečys, P., Voisiat, B. & Gedvilas, M. Use of High Repetition Rate and High Power Lasers in Microfabrication: How to Keep the Efficiency High? J. Laser Micro Nanoen. 4, 186–191 (2009).
Jaeggi, B. et al. Laser Micromachining of Metals with Ultra-Short Pulses: Factors Limiting the Scale-Up. Process. J. Laser Micro Nanoen. 12, 267–273 (2017).
Jaeggi, B., Remund, S., Zhang, Y., Kramer, T. & Neuenschwander, B. Optimizing the Specific Removal Rate with the Burst Mode Under Varying Conditions. J. Laser Micro Nanoen. 12, 258–266 (2017).
Schille, J., Schneider, L. & Loeschner, U. Process optimization in high-average-power ultrashort pulse laser microfabrication: how laser process parameters influence efficiency, throughput and quality. Appl. Phys. A Mater. Sci. Process. 120, 847–855 (2015).
Neuenschwander, B., Jaeggi, B., Foerster, D. J., Kramer, T. & Remund, S. Influence of the burst mode onto the specific removal rate for metals and semiconductors. J. Laser Appl. 31, 22203 (2019).
Mishchik, K. et al. High-efficiency femtosecond ablation of silicon with GHz repetition rate laser source. Opt. Lett. 44, 2193–2196 (2019).
Mirza, I. et al. Ultrashort pulse laser ablation of dielectrics: Thresholds, mechanisms, role of breakdown. Sci. Rep. 6, 39133 (2016).
Chen, H., Li, H., Sun, Y. C., Wang, Y. & Lü, P. J. Femtosecond laser for cavity preparation in enamel and dentin: ablation efficiency related factors. Sci. Rep. 6, 20950 (2016).
Chen, T., Fardel, R. & Arnold, C. B. Ultrafast z-scanning for high-efficiency laser micro-machining. Light Sci. Appl. 7, 17181 (2018).
Kramer, T. et al. Increasing the Specific Removal Rate for Ultra Short Pulsed Laser-Micromachining by Using Pulse Bursts. J. Laser Micro Nanoen. 12, 107–114 (2017).
Gaidys, M., Žemaitis, A., Gečys, P. & Gedvilas, M. Efficient picosecond laser ablation of copper cylinders. Appl. Surf. Sci. 483, 962–966 (2019).
Žemaitis, A. et al. Advanced laser scanning for highly-efficient ablation and ultrafast surface structuring: experiment and model. Sci. Rep. 8, 17376 (2018).
Liu, J. M. Simple technique for measurements of pulsed Gaussian-beam spot sizes. Opt. Lett. 7, 196–198 (1982).
Sun, H. Thin lens equation for a real laser beam with weak lens aperture truncation. Opt. Eng. 37, 2906–2913 (1998).
Armbruster, O., Naghilou, A., Kitzler, M. & Kautek, W. Spot size and pulse number dependence of femtosecond laser ablation thresholds of silicon and stainless steel. Appl. Surf. Sci. 396, 1736–1740 (2017).
Naghilou, A., Armbruster, O. & Kautek, W. Femto- and nanosecond pulse laser ablation dependence on irradiation area: The role of defects in metals and semiconductors. Appl. Surf. Sci. 418, 487–490 (2017).
Wu, C. & Zhigilei, L. V. Microscopic mechanisms of laser spallation and ablation of metal targets from large-scale molecular dynamics simulations. Appl. Phys. A Mater. Sci. Process. 114, 11–32 (2014).
Förster, D. J. et al. Shielding effects and re-deposition of material during processing of metals with bursts of ultra-short laser pulses. Appl. Surf. Sci. 440, 926–931 (2018).
Jäggi, B., Förster, D. J., Weber, R. & Neuenschwander, B. Residual heat during laser ablation of metals with bursts of ultra-short pulses. Adv. Opt. Technol. 7 (2018).
Žemaitis, A., Mikšys, J., Gaidys, M., Gečys, P. & Gedvilas, M. High-efficiency laser fabrication of drag reducing riblet surfaces on pre-heated Teflon. Mater. Res. Express 6, 065309 (2019).
Matsumoto, H., Lin, Z. & Kleinert, J. Ultrafast laser ablation of copper with ~GHz bursts. Proc. SPIE 10519, (1051902 (2018).
Elahi, P. et al. High-power Yb-based all-fiber laser delivering 300 fs pulses for high-speed ablation-cooled material removal. Opt. Lett. 43, 535–538 (2018).
Hu, W., Shin, Y. C. & King, G. Modeling of multi-burst mode pico-second laser ablation for improved material removal rate. Appl. Phys. A 98, 407–415 (2010).
Neuenschwander, B., Kramer, T., Lauer, B. & Jaeggi, B. Burst mode with ps- and fs-pulses: Influence on the removal rate, surface quality and heat accumulation. Proc. SPIE 9350, 93500U–1 (2015).
Winter, J., Rapp, S., Schmidt, M. & Huber, H. P. Ultrafast laser processing of copper: A comparative study of experimental and simulated transient optical properties. Appl. Surf. Sci. 417, 2–15 (2017).
Author information
Authors and Affiliations
Contributions
A.Ž. conceived the original idea for the research. P.G. communicated with M.B., who agreed to provide the state-of-the-art femtosecond burst laser with controllable pulse duration for the experiments. A.Ž. designed and performed the experiments, analysed the data and wrote the manuscript. A.Ž., G.R., P.G. and M.G. discussed on the results. All co-authors commented on the manuscript. A.Ž. performed a revision of manuscript according to the reviewers’ and editors comments. All co-authors commented on the revised manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Žemaitis, A., Gečys, P., Barkauskas, M. et al. Highly-efficient laser ablation of copper by bursts of ultrashort tuneable (fs-ps) pulses. Sci Rep 9, 12280 (2019). https://doi.org/10.1038/s41598-019-48779-w
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-48779-w
This article is cited by
-
Bi-stability in femtosecond laser ablation by MHz bursts
Scientific Reports (2024)
-
Supercontinuum generation in bulk solid-state material with bursts of femtosecond laser pulses
Scientific Reports (2024)
-
Fundamentals and comprehensive insights on pulsed laser synthesis of advanced materials for diverse photo- and electrocatalytic applications
Light: Science & Applications (2022)
-
Secondary electron yield reduction of copper after 355 nm ultrashort pulse laser ablation
Lasers in Manufacturing and Materials Processing (2022)
-
High-quality laser processing of fused silica with bursts of ultrafast pulses
Applied Physics A (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.