Electrical writing, deleting, reading, and moving of magnetic skyrmioniums in a racetrack device


A magnetic skyrmionium (also called 2π-skyrmion) can be understood as a skyrmion—a topologically nontrivial magnetic whirl—which is situated in the center of a second skyrmion with reversed magnetization. Here, we propose a new optoelectrical writing and deleting mechanism for skyrmioniums in thin films, as well as a reading mechanism based on the topological Hall voltage. Furthermore, we point out advantages for utilizing skyrmioniums as carriers of information in comparison to skyrmions with respect to the current-driven motion. We simulate all four constituents of an operating skyrmionium-based racetrack storage device: creation, motion, detection and deletion of bits. The existence of a skyrmionium is thereby interpreted as a ‘1’ and its absence as a ‘0’ bit.


Magnetic skyrmions1,2,3 are whirl-like quasiparticles that are under consideration as carriers of information in modern data storages: Sampaio et al.4 proposed to write and move skyrmions in thin film nanowires what constitutes a derivative of a racetrack storage device, initially proposed for domain walls in a ferromagnetic thin films5,6,7. The low driving current, small size and high stability of skyrmions, combined with the stackability of these tracks into three dimensions may lead to the development of highly efficient magnetic memory-storage devices with capacities that rival those of magnetic hard-disk drives, satisfying the ever-growing demand for data storage.

Since the initial discovery of skyrmions in the form of periodic lattices in bulk single crystals of MnSi2, scientific effort has led to promising advances towards the utilization of isolated skyrmions as information carriers4,8,9,10,11,12,13. Still, one major issue for  driving skyrmions on a racetrack is the skyrmion Hall effect3,11,14,15 originating from the real-space topological properties of skyrmions. A skyrmion carries a topological charge of NSk ± 1, defined as the integral over the topological charge density

$${n}_{{\rm{Sk}}}({\boldsymbol{r}})=\frac{1}{4\pi }{\boldsymbol{m}}({\boldsymbol{r}})\cdot [\frac{\partial {\boldsymbol{m}}({\boldsymbol{r}})}{\partial x}\times \frac{\partial {\boldsymbol{m}}({\boldsymbol{r}})}{\partial y}],$$

where m(r) is the unit vector magnetization field. Skyrmions driven by spin-polarized electrical currents are not propelled parallel to the racetrack. They experience a transverse deflection towards the edge of the racetrack where they may be confined. This effect is detrimental for racetrack applications.

Theoretical suggestions for suppressing the skyrmion Hall effect are to manipulate the driving torque orientation16,17,18,19 or to use antiferromagnetic skyrmions with a vanishing topological charge20,21,22,23 instead of skyrmions. However, both approaches have not yet been realized experimentally.

Here, we utilize another type of magnetic quasi-particle (Fig. 1a) with a zero topological charge: the skyrmionium (also called a 2π-skyrmion)24,25,26,27,28,29,30,31,32,33,34. The skyrmionium has been observed experimentally created by laser pulses27, as target skyrmionium in nanodiscs28 and very recently in a thin ferromagnetic film on top of a topological insulator29. A magnetic skyrmionium (Fig. 1b) can be described as a skyrmion, with a second skyrmion situated in the center. The inner skyrmion has a reversed polarity and deforms the outer skyrmion to a ring.

Figure 1

Skyrmionium-based racetrack storage device. (a) Schematic presentation of the proposed device including the four constituents: writing, deleting, moving and reading. A skyrmionium, the circular object in the Co layer (gray), is written or deleted by a photosensitive switch built from gold (Au) and a semi-conductor (SC). A radial current (white) is triggered upon illuminating the antenna with a fs-laser pulse due to the applied bias voltage. The current mainly flows in the Pt layer (transparent) where the SHE injects spins (cyan) into the Co layer that are oriented perpendicularly to the plane normal and current directions. Depending on the polarity of the gate voltage, the sign of the optically activated current pulse and the orientation of the polarization are determined, so that a skyrmionium can be written or deleted. To move the skyrmionium a uniform current density j is applied along the track, again generating spins s that exert a SOT onto the skyrmionium. When a skyrmionium is located near the two leads on the right, a Hall voltage UR can be measured, allowing for a distinct detection of a skyrmionium bit. (b) (top) Magnetic texture of a skyrmionium, and (bottom) topological charge density nSk with opposite signs for the inner skyrmion and the outer ring.

Here, we show that skyrmioniums can be used as carriers of information in a racetrack storage device (Fig. 1a): the existence of a skyrmionium is interpreted as a ‘1’ bit, while its absence is a ‘0’ bit. Based on recent progresses in optically generated current pulses35 we propose a way to write and delete magnetic skyrmioniums on the picosecond timescale, so that the current-induced skyrmionium flow–without the detrimental skyrmion Hall effect–can remain steady while writing. Also we show that skyrmioniums can be detected electrically by their topological Hall signal, that arises from the local topological charge density (Fig. 1b bottom), even though the global topological charge vanishes.


Skyrmionium racetrack

In the following, we simulate and analyze point by point the four essential constituents to operate a racetrack-storage device based on magnetic skyrmioniums. First, we show via micromagnetic simulations how skyrmioniums can be written and deleted by optically excited localized current pulses. Thereafter, we present advantages in the current-driven motion of skyrmioniums compared to that of conventional skyrmions; we explain the simulated results by an effective description using the Thiele equation. Ultimately, we show via Landauer-Büttiker calculations that the local separation of the two subskyrmions of a skyrmionium can be exploited to electrically detect skyrmioniums even though they exhibit no topological Hall voltage when integrated over the whole sample.

For the device (Fig. 1a) we consider a magnetic layer on a heavy metal: here we exemplarily select Co (gray) on Pt (transparent), as in refs4,26. In this setup an applied charge current density j (white) within the Pt layer is translated into  a spin current by the considerable spin Hall effect that has been observed in Pt. The spin current flows perpendicularly to the plane into the Co potentially hosting skyrmioniums. The spin polarization s (cyan) is perpendicular to j and the plane normal, thereby leading to a spin-orbit torque36 (SOT) that can propel a skyrmionium.

On top of the basic racetrack that is formed from the Pt/Co bilayer a photosensitive switch37 is fabricated that can switch the magnetization as experimentally shown in ref.35. A circular gold disk inside a gold ring is isolated from the metallic racetrack by an underlying semiconducting layer (green) so that a bias voltage can be applied between the inner and outer gold electrodes (Corbino geometry). The semiconductor is electrically activated by fs-laser pulses which generate a radially symmetric current pulse profile \({\boldsymbol{j}}={j}_{{\rm{write}}}\frac{{r}_{0}}{r}\,{\hat{e}}_{r}\) (white) in the Pt-layer.  By analogy with the explanation given above, this leads to a toroidal spin polarization profile \({\boldsymbol{s}}({\boldsymbol{r}})||\pm {\hat{e}}_{\varphi }\) (cyan) of the spin currents (parallel to \({\hat{e}}_{z}\)) that diffuse into the Co layer to create or delete the skyrmionium. To model the skyrmionium generation, deletion and motion we use a micromagnetic framework based on the Landau-Lifshitz-Gilbert (LLG) equation36,38,39. For details and simulation parameters see Methods.

For the reading process we utilize the local topological properties of a skyrmionium. The non-zero topological charge density nSk leads to a deflection of electrons into a transverse direction. A Hall voltage UR builds up that can be measured by attaching two small leads (gray) to the sides of the device.

Optoelectrical writing of skyrmioniums

Several mechanisms for writing skyrmions have been proposed, such as the application of spin-polarized currents40, laser beams27 and electron beams41,42. These mechanisms can potentially be adapted to generate also skyrmioniums. It has been predicted that skyrmioniums can be generated by alternating the out-of-plane orientation of an external magnetic field30 or by the perpedicular injection of spin currents26,31.

We propose a faster writing mechanism, where spins are injected from the perpendicular direction for an ultrashort duration. We consider a SOT-driven approach based on a nanostructured skyrmionium manipulation unit as sketched in Fig. 1a. Optically excited radially symmetric charge currents (white) in the Pt-layer lead to out-of-plane spin currents with a controllable toroidal spin polarization configuration (cyan): For opposite signs of the applied bias-voltage opposite spin polarizations are achieved (\(\pm {\hat{e}}_{\phi }\)). According to Yang et al.35 current densities on the order of jmax = 2 × 1013A/m2 could be created for a pulse duration of 9 ps full width at half maximum (FWHM). These values were adapted in our proposed optoelectrical writing and deleting process of a single skyrmionium. They cannot be reached by a conventional perpendicular spin current injection. The diameter of the inner disk of the photosensitive switch is 20 nm and the outer ring’s inner diameter is 60 nm in order to match the skyrmionium’s dimension. These dimensions are at the limit of what is possible today using conventional lithographic processes.

Starting from an initially uniform magnetization pointing into the −z direction (Fig. 2a), the system is excited by an out-of-plane spin current with toroidal polarization. Because of the ultrashort current pulses of 9 ps (FWHM) the excitation itself is non-adiabatic and the magnetic texture will relax on a longer time scale.

Figure 2

Writing skyrmioniums by optically excited current pulses. (a) The starting point is a ferromagnet magnetized along −z. The orange areas indicate the gold nanostructures that generate a current pulse of 9 ps duration (FWHM) with jmax(t = 15 ps) = 2 × 1013A/m2 at the disk. (b) After the spin current has induced a skyrmionium-shaped excitation the quasiparticle relaxes in (cf). The color code is the same as in Fig. 1. An animated version is accessible in Supplementary Video 1. For sample and beam parameters see text and Methods. The scale bar corresponds to 50 nm.

During the current-pulse (Fig. 2b, maximum current at 15 ps) the magnetization in the excited ring-shaped region begins to align with the spin current’s polarization, i.e. along \(-{\hat{e}}_{\phi }\). The amplitude of the current as well as its location needs to be tuned in such a way, that it will effectively switch a ring-shaped domain of a suitable size (Fig. 2c). Subsequently not only spin waves propagate radially, but also the central circular region remaining in its initial orientation starts to pulsate (Fig. 2c–f). Associated with this, the domain wall between the central −z region and the intermediate +z region is rotating such that a central Néel-skyrmion is generated, thereby, in total, constituting a skyrmionium. The slowest relaxation is the adjustment of the skyrmionium’s size, taking place after the central fluctuations decay. The shrinking towards the final diameter (around 80 nm) lasts for ~500 ps (Fig. 2e,f).

Optoelectrical deleting of skyrmioniums

Deleting a non-collinear magnetic texture means turning it into a ferromagnetic state. Since no stabilizing external magnetic field is applied to the racetrack, the magnetization can in principle point into both out-of-plane directions. The uncontrolled annihilation of a skyrmionium can therefore easily lead to a local reversal of the magnetization direction, i. e., the formation of a domain. Therefore ‘1’ bits need to be turned into ‘0’ bits in a controlled way; no ferromagnetic domains must form. An efficient way is to invert the writing mechanism by reversing the bias voltage, which goes along with a change of the spin current’s polarization from \(-{\hat{e}}_{\phi }\) to \(+{\hat{e}}_{\phi }\).

The annihilation process is shown in Fig. 3. The generated spin current effectively unwinds the skyrmionium structure step by step. First, the rotation of the domain wall leads to the dissolving of the central −z domain (Fig. 3a–c). Second, the remaining skyrmion-like configuration contracts (Fig. 3d,e) until it collapses (Fig. 3f). The system relaxes towards the ferromagnetic state in less than 40 ps.

Figure 3

Deleting skyrmioniums by optically excited current pulses. (a) We start from the skyrmionium stabilized in Fig. 2 and generate a spin current with opposite polarization (\({\hat{e}}_{\phi }\)) compared to the writing process achieved by switching the sign of the bias voltage. (b,c) The domain wall unwinds the inner skyrmion leading to its collapse. (df) Subsequently, the skyrmion-like configuration contracts and dissolves. An animated version is accessible in Supplementary Video 2. The scale bar corresponds to 50 nm.

Current-driven motion of skyrmioniums

Skyrmions and skyrmioniums can be driven by spin torques. As discussed above, we use a two-layer setup that utilizes SOT, which means \({\boldsymbol{s}}||\) − y for j||x. This mechanism has been proven to be far more efficient compared to propagation induced by spin-polarized currents applied within the ferromagnetic layer (spin-transfer torque)4,26.

In our simulations (Fig. 4a,b) a reference skyrmion (Fig. 4b) first moves to the edge partially along the −y direction of the racetrack for about 10 ns and then moves at a steady velocity along the confining edge along the +x direction. The skyrmionium (Fig. 4a) on the other hand is propelled almost instantly to the steady state velocity and moves in the middle of the racetrack along +x.

Figure 4

Current-driven motion of skyrmioniums. (a) A skyrmionium in a racetrack is driven by SOT: applied current density jxΘSH = 0.6 MA/cm2, injected spins are oriented along −y. (b) The motion of a skyrmion is shown for comparison. In both cases the image is taken after 50 ns of propagation time. The orange curve shows the trajectory of the quasiparticles’ centers (starting point is indicated by 0 ns). The blue line indicates the motion direction under the skyrmion Hall angle, calculated from the Thiele equation (see text). (c) The results of a ‘writing-under-current’ simulation are shown after 35 ns propagation time in a racetrack with a doubled length. Due to the stronger current (jxΘSH = 2.0 MA/cm2) the skyrmioniums are slightly deformed. Skyrmioniums are written after 0 ns, 5 ns, 15 ns, 20 ns, 25 ns, and 35 ns. The last skyrmion is not yet fully relaxed. An animated version of the skyrmionium-sequence generation is accessible in the Supplementary Video 3. The scale bar corresponds to 100 nm.

The results of micromagnetic simulations can most easily be understood by an effective center-of-mass description of magnetic quasiparticles (velocity v): the Thiele equation (in units of force)4,19,26,43

$${b}\,{\boldsymbol{G}}\times {\boldsymbol{v}}-b\underline{D}\alpha {\boldsymbol{v}}+Bj\underline{I}{\boldsymbol{s}}=\nabla U(y\mathrm{).}$$

The properties of the respective quasiparticle are condensed into the gyromagnetic coupling vector G = Gez with G = −4πNSk, and the dissipative tensor \(\underline{D}\) determined by \({D}_{ij}=\int \,{{\rm{\partial }}}_{i}{\boldsymbol{m}}({\boldsymbol{r}})\cdot {{\rm{\partial }}}_{j}{\boldsymbol{m}}({\boldsymbol{r}})\,{{\rm{d}}}^{2}r\). Only Dxx and Dyy are nonzero. The tensor \(\underline{I}\) is calculated from \({I}_{ij}=\int \,{[{{\rm{\partial }}}_{i}{\boldsymbol{m}}({\boldsymbol{r}})\times {\boldsymbol{m}}({\boldsymbol{r}})]}_{j}\,{{\rm{d}}}^{2}r\) and has only nonzero xy and yx elements for the stabilized Néel skyrmion (the type of skyrmion is determined by the Dzyaloshinskii-Moriya interaction (DMI)44,45 arising at the interface between the Pt and Co layers) and skyrmionium. This tensor describes the interaction of injected spins s and the magnetic texture. The constants are b = Msdz/γe and B = /(2eSH.

While neglecting the racetrack potential U (minimum in the middle of the racetrack), both textures experience a skyrmion Hall angle of θSk = arctan(G/Dxxα), which gives an angle of −60.5° for the skyrmion and 0° for the skyrmionium with respect to the +x direction, in agreement with the first period of the simulation (blue dashed lines in Fig. 4a,b). The magnetic quasiparticles move at a velocity of

$${v}_{x}=\frac{B}{b}\frac{{I}_{xy}}{{D}_{xx}}\frac{1}{\alpha }{j}_{x}-\,\tan \,{\theta }_{{\rm{Sk}}}{v}_{y}$$

along the racetrack. If the current density jx is small enough, a skyrmion moves to the edge of the racetrack due to its topological charge, until the gradient potential of the racetrack edge compensates the transverse force. In this case the longitudinal velocity is increased, because the second term vanishes. Due to θSk = 0 a skyrmionium on the other hand moves instantly at a constant velocity, which is given by the first term of Eq. 3.

In agreement with ref.26 we find a slightly increased skyrmionium velocity (\(|{v}_{x}^{{\rm{s}}{\rm{t}}}|=13.8\,{\rm{m}}/{\rm{s}}\)) compared to the skyrmion velocity (\(|{v}_{x}^{{\rm{s}}{\rm{t}}}|=13.2\,{\rm{m}}/{\rm{s}}\)) even in the steady state, which is explained by vxIxy/Dxx in Eq. 3. In infinitely wide racetracks this ratio is equal for skyrmions and skyrmioniums. In finite tracks however, the confining potential deforms the magnetic quasiparticles slightly, altering the above ratio. Since skyrmioniums are larger than skyrmions, they experience a stronger deformation which manifests itself in a slightly increased Ixy/Dxx ratio.

The striking advantage of skyrmioniums as carriers of information compared to skyrmions becomes apparent in the first 10 ns of their motion after a current pulse is applied. During this period of time the skyrmionium already moves at maximum speed in the middle of the track, thereby allowing the writing of several skyrmioniums in sequence while the driving current is still applied (Fig. 4c).

Similarly to the skyrmion-skyrmion interaction46, also the interaction between skyrmioniums is decreasing exponentially with the distance between them (see Supplementary Fig. S1). A repulsion of the quasiparticles is mainly limited to the case of a spatial overlap of the spin textures, therefore leaving the inter-skyrmionium distance in Fig. 4c constant during the considered time period.

In Fig. 4c we apply a current density of jΘSH = 2.0 MA/cm2. The skyrmionium moving at 46.28 m/s is no longer rotationally symmetric: Its inner part is pushed to the top while the outer ring is dragged to the bottom of the racetrack, in accordance with the opposite skyrmion Hall effects that originate in the opposite partial topological charges of the two skyrmionium parts.

The maximal current density that can be applied to skyrmions and skyrmioniums is limited to around the same value. When the driving current is too large skyrmioniums self destruct because the forces pushing the two parts of the skyrmionium in opposite directions become too large26 (For an analysis of the current dependence of the skyrmionium velocity and stability see Supplementary Fig. S2). On the other hand skyrmions are annihilated at the edge. For skyrmioniums the steady state velocity can be increased up to around 140 m/s. Alternatively, skyrmioniums can also be driven by spin waves32,33.

Electrical reading of skyrmioniums

Due to its distinct magnetization a skyrmionium can easily be detected by out-of-plane measurements. However, electrical in-plane measurement can be included in the racetrack geometry more easily. For this reason we consider detection of skyrmioniums via the Hall voltage as has been done experimentally for conventional skyrmions9.

When a small reading current I is applied along the track, the Hall resistivity is given by anomalous Hall and topological Hall contributions. The anomalous contribution is proportional to the net magnetization of the texture between the two detecting leads. For this reason every non-collinear magnetic texture is easily detected by the anomalous Hall effect. However, the signal is rather similar for different textures. Skyrmioniums cannot unambiguously be distinguished from skyrmions or even domain walls. This problem is resolved by the additional topological contribution to the Hall effect.

The topological Hall effect3,9,10,47,48,49,50,51,52 is a hallmark of the skyrmion phase: Traversing electrons are deflected into a transverse direction, since their spins (partially) align with the non-collinear texture and a Berry phase is accumulated. The topological charge density acts like a fictitious magnetic field, called an emergent field3. We show that even though a skyrmionium has a zero topological charge it exhibits a distinct topological Hall signal that allows for a failsafe detection of skyrmioniums as ‘1’ bits in comparison to other non-collinear textures that may appear as defects in imperfect racetracks.

We calculate the Hall resistance for skyrmioniums in a racetrack by means of the Landauer-Büttiker formalism53,54, by analogy with refs10,52 where skyrmions have been considered (see Methods for details). To model the interaction of electrons with the magnetic texture we considered a tight-binding model, which features nearest-neighbor hopping (amplitude t; creation and annihilation operator \({c}_{i}^{\dagger }\), ci) and a Hund’s coupling term (amplitude m, vector of Pauli matrices σ)

$$H=\sum _{\langle i,j\rangle }\,t\,{c}_{i}^{\dagger }{c}_{j}+m\sum _{i}\,{{\boldsymbol{m}}}_{i}\cdot ({c}_{i}^{\dagger }{\boldsymbol{\sigma }}{c}_{i}\mathrm{).}$$

Without the presence of skyrmioniums the Hamiltonian for the ferromagnet gives the energy bands E = 2t[cos(kxa) + cos(kya)] ± m. Since skyrmions are detected most easily for low carrier concentrations10, we set the Fermi energy of the system close to the lower band edge, where the electrons behave like free electrons (EF = −8.5 t for m = 5 t).

Since NSk = 0 the topological Hall effect vanishes globally: The inner part of the skyrmion deflects electrons to the bottom, while the outer ring redirects electrons into the opposite direction. Fortunately, this spatial separation of the two opposing contributions leads to a non-zero signal in a local measurement (Fig. 5). The topological Hall resistance Rxy = (Uup − Udown)/I is determined by the difference in voltage U at the two leads normalized by the reading current.

Figure 5

Electrical reading of skyrmioniums. The black curve shows the calculated transverse resistance signal when the skyrmionium sequence (top panel) passes the leads. In the presence of a skyrmionium between the leads (green background) a distinct pattern is found that exceeds two thresholds (dashed lines) three times. In good approximation the signal is proportional to the integrated topological charge density between the leads (orange). If no skyrmionium is present (red) the curve fluctuates around zero. Parameters: skyrmionium radius: 40 sites, track width: 120 × 2000 sites, bit width: 240 sites, lead width: 29 sites, m/t = 5, EF = −8.5 t.

Whenever a skyrmionium approaches the contacts, at first only electrons deflected by the outer ring are detected. Later, when the skyrmionium is right between the leads, the inner part dominates the electron deflection and the effective charge accumulation is reversed. Finally, upon leaving the vicinity of the contacts, only the outer ring contributes to the signal. This leads to a characteristic curve that is well approximated (orange) by the topological charge density between the leads for a skyrmionium at position x

$${R}_{xy}(x)\propto {\int }_{y}\,{\int }_{-{x}_{0}}^{{x}_{0}}\,{n}_{{\rm{Sk}}}(x-x^{\prime} ,y^{\prime} )\,{\rm{d}}x^{\prime} {\rm{d}}y^{\prime} .$$

Electrons that traverse the spin texture are deflected by the locally nonzero emergent field of the skyrmionium BemnSkez to the leads (voltage Uup and Udown) of finite width ranging from x = −x0 to +x0. Note, that for x0 → ∞ the result of zero global resistivity is recovered, independent of the position of the skyrmionium.


In this Paper we simulated the four fundamental constituents of a racetrack storage device utilizing magnetic skyrmioniums as carriers of information.

For the writing and deleting mechanism we proposed a new method that utilizes the optoelectrical control of localized spin currents and their polarizations. Based on previous experimental advances we designed a nanostructured geometry enabling the writing or deleting of single skyrmionium bits, depending on the sign of the bias voltage. Since the writing process is ultrafast, skyrmioniums can be written while the driving current is applied even at the maximal velocity of the bits along the track of around 140 m/s (Fig. 4c). The reliability of this deterministic method is emphasized by the result, that an excitation with the ‘wrong’ gate voltage cannot change an existing bit (see Supplementary Videos 4 and 5). In that case the spin current’s associated chirality is not suited to wind or unwind the present configuration, respectively. Furthermore, even when room temperature fluctuations (see Methods for details) are accounted for, the proposed manipulation technique still works (see Supplementary Fig. S3 and Videos 6 and 7) what makes the presented mechanism highly attractive over other proposals. Also, we checked the range of parameters characterizing the optoelectrical writing mechanism that allow for a controlled generation of skyrmioniums (cf. Supplementary Fig. S4).

We analyzed the motion of skyrmioniums under application of electrical currents in the Pt layer where a spin current is injected perpendicularly into the Co layer (SOT). Due to their vanishing topological charge, skyrmioniums move in the middle of the racetrack and reach a steady state of motion almost instantly.

Reading magnetic skyrmioniums is possible via measurements of the Hall voltage. A local drop in the net magnetization leads to the emergence of an anomalous Hall effect and the segregation of the two skyrmionic subsystems even allows for the detection of a topological contribution: While the outer ring deflects electrons into one transverse direction, the inner ring redirects electrons into the other direction. Since the detecting leads are of finite size, one observes an oscillating Hall signal when the skyrmionium moves through them allowing for a highly reliable reading process.

Compared to skyrmions the main advantages of utilizing skyrmioniums as bits of information are (a) the slightly higher velocity (effect increases for narrower racetracks), (b) the absence of an acceleration phase (vx is instantly proportional to jx; this effect is more prominent for a wider track), and (c) the skyrmionium moves always in the middle of the track. Advantages (b) and (c) are essential for an effective reading process, allow for changes in the moving direction and–combined with the ultrafast writing speed of the presented optoelectrical approach–allow for a convenient ‘writing-while-moving’ as well as ‘deleting-while-moving’ functionality of a skyrmionium racetrack (cf. Fig. 4c).

In conclusion, writing and reading of magnetic skyrmioniums in thin films can be exploited to allow for the operation of an efficient skyrmionium-based racetrack storage device. In contrast to other magnetic quasiparticles, that are predicted to move without a skyrmion Hall effect, skyrmioniums have already been detected in experiments. Our proposals will expedite the development of a working data storage device based on magnetic quasiparticles.


Micromagnetic simulations

We use the GPU-accelerated micromagnetic software package Mumax355,56 to solve the LLG equation with the SOT term for every magnetic moment mi of the discretized magnetization36,38,39

$${\dot{{\boldsymbol{m}}}}_{i}=-\,{\gamma }_{e}{{\boldsymbol{m}}}_{i}\times {{\boldsymbol{B}}}_{i,{\rm{eff}}}+\alpha {{\boldsymbol{m}}}_{i}\times {\dot{{\boldsymbol{m}}}}_{i}+{\gamma }_{e}\epsilon \beta [({{\boldsymbol{m}}}_{i}\times {\boldsymbol{s}})\times {{\boldsymbol{m}}}_{i}\mathrm{].}$$

Here, γe = 1.760 × 1011T−1 s−1 is the gyromagnetic ratio of an electron. The in-plane torque coefficient is \(\varepsilon \beta =\frac{\hslash j{{\rm{\Theta }}}_{{\rm{SH}}}}{2e{d}_{z}{M}_{s}}\); the out-of-plane torque parameter is set zero as it is small and does not drive the quasiparticles. The space- and time-dependent effective magnetic field

$${{\boldsymbol{B}}}_{{\rm{eff}}}^{i}=-\,\frac{\delta F[{\boldsymbol{m}}]}{{M}_{s}\delta {{\boldsymbol{m}}}_{i}}$$

is derived from the system’s total free energy density F, given as the sum of exchange interaction, magnetocrystaline anisotropy, the demagnetization field, Zeeman energy, and DMI.

To generate skyrmioniums we use a modified photosensitive switch setup as shown in Fig. 1a, motivated by the experimental results from Yang et al.35. As discussed in the main text an optoelectrically induced spin current is superposed on the uniform spin current, which drives the skyrmioniums along the racetrack. For the simulations we assumed a Gaussian envelope in time according to ref.35.

Additionally, for the room temperature simulations an effective thermal field is included as

$${{\boldsymbol{B}}}_{{\rm{therm}}}^{{i}}={\boldsymbol{\eta }}\sqrt{\frac{2\alpha {\mu }_{0}{k}_{{\rm{B}}}T}{{M}_{s}\gamma {\rm{\Delta }}V{\rm{\Delta }}t}},$$

where η is a random vector generated according to a standard normal distribution for each simulation cell and changed after every time step. kB is Boltzmann’s constant, T the temperature, ΔV the simulation cells’ size and Δt the time simulation’s step. The thermal fluctuations due to the room-temperature ambience lead to deformations of the skyrmionium structure, but the switching mechanism still works successfully.

The system of Co/Pt is described by the following parameters4,26: saturation magnetization Ms = 0.58 MA/m, exchange stiffness A = 15 pJ/m, interfacial DMI D = 3.5 mJ/m2, uniaxial anisotropy in z-direction Kz = 0.8 MJ/m3, Gilbert damping parameter α = 0.3 and the spin Hall angle ΘSH = 0.4. We simulate a Co nanowire racetrack of width 150 nm and thickness dz = 1 nm, and discretize the magnetization in cubic cells of size 1 nm3.

We use these values for comparability with refs4,26, while noting that the DMI constant57 and the spin Hall angle58 are still under debate. For the here presented parameters a skyrmionium is stable for DMI strengths between 3.3 mJ/m2 and 3.7 mJ/m2 (cf. Supplementary Fig. S5). In this context we note, that the effective DMI constant can be tuned, for instance as in a Pt/Co/Ir setup presented in ref.59 or by utilizing a different bilayer system, what is possible since our predictions are generally applicable and not limited to Co/Pt interfaces.

Topological Hall effect calculations

To calculate the topological Hall resistivity we consider the tight-binding Hamiltonian (Eq. 4) on a finite square lattice that forms the racetrack, as in Fig. 5. We apply four leads to the track: to the left and right to inject a small reading current, i. e., Il = −Ir = I and Vl = −Vr, and up and down to detect the voltage due to the transverse deflection and accumulation of the electrons, i. e., Iu = Id = 0 and Vu and Vd. The transverse resistance follows directly from these voltages and currents, see text. To calculate the relationship between the currents and voltages we use a Landauer-Büttiker approach53,54, by analogy with refs10,52, where skyrmions have been investigated. For the calculations we use the transport simulation package Kwant60.

We solve the set of linear equations {m, n} = {l, r, u, d}

$${I}_{m}=\frac{{e}^{2}}{h}\sum _{n}\,{T}_{mn}{V}_{n},$$

containing the transition matrix

$${T}_{mn}={\rm{Tr}}({{\rm{\Gamma }}}_{m}{G}_{mn}{{\rm{\Gamma }}}_{n}{G}_{mn}^{\dagger }),$$

for the current I and non-fixed voltages Vu and Vd. Here, the retarded Green’s function

$${\boldsymbol{G}}={(E-H-\sum {{\rm{\Sigma }}}_{{\rm{i}}})}^{-1}$$

and \({{\rm{\Gamma }}}_{i}={\rm{i}}({{\rm{\Sigma }}}_{{\rm{i}}}-{{\rm{\Sigma }}}_{{\rm{i}}}^{\dagger })\) enter (E energy, H tight-binding Hamiltonian). Σi is the self energy of the i th lead.

Analyzing the results for different geometric parameters we find that skyrmioniums need to have a minimal size so that the topological charge density is well resembled. The leads should not be too large (optimally below half the skyrmionium radius) since they integrate the locally distinct signal making it broader and ambiguous. The distance between two bits can be small but then their signals begin to overlap, hampering an unambiguous detection. A minimal distance is given by 2(r0 + x0), which is the width of the predicted signal (orange). In ‘0’ bit regions oscillations of the signal around zero are visible originating from backscattering of electrons from the racetrack edges. This unfavorable effect decreases for wider tracks.


  1. 1.

    Bogdanov, A. & Yablonskii, D. Thermodynamically stable vortices in magnetically ordered crystals. the mixed state of magnets. Zh. Eksp. Teor. Fiz 95, 182 (1989).

    Google Scholar 

  2. 2.

    Mühlbauer, S. et al. Skyrmion lattice in a chiral magnet. Science 323, 915–919 (2009).

    ADS  Article  Google Scholar 

  3. 3.

    Nagaosa, N. & Tokura, Y. Topological properties and dynamics of magnetic skyrmions. Nature Nanotechnol. 8, 899–911 (2013).

    ADS  CAS  Article  Google Scholar 

  4. 4.

    Sampaio, J., Cros, V., Rohart, S., Thiaville, A. & Fert, A. Nucleation, stability and current-induced motion of isolated magnetic skyrmions in nanostructures. Nature Nanotechnol. 8, 839 (2013).

    ADS  CAS  Article  Google Scholar 

  5. 5.

    Parkin, S. S. P. Shiftable magnetic shift register and method of using the same. US Patent 6,834,005 (2004).

  6. 6.

    Parkin, S. S. P., Hayashi, M. & Thomas, L. Magnetic domain-wall racetrack memory. Science 320, 190–194 (2008).

    ADS  CAS  Article  Google Scholar 

  7. 7.

    Parkin, S. S. P. & Yang, S.-H. Memory on the racetrack. Nature Nanotechnol. 10, 195–198 (2015).

    ADS  CAS  Article  Google Scholar 

  8. 8.

    Romming, N. et al. Writing and deleting single magnetic skyrmions. Science 341, 636–639 (2013).

    ADS  CAS  Article  Google Scholar 

  9. 9.

    Maccariello, D. et al. Electrical detection of single magnetic skyrmions in metallic multilayers at room temperature. Nature Nanotechnol. 13, 233–237 (2018).

    ADS  CAS  Article  Google Scholar 

  10. 10.

    Hamamoto, K., Ezawa, M. & Nagaosa, N. Purely electrical detection of a skyrmion in constricted geometry. Appl. Phys. Lett. 108, 112401 (2016).

    ADS  Article  Google Scholar 

  11. 11.

    Jiang, W. et al. Direct observation of the skyrmion Hall effect. Nat. Phys. 13, 162–169 (2017).

    CAS  Article  Google Scholar 

  12. 12.

    Kang, W., Huang, Y., Zhang, X., Zhou, Y. & Zhao, W. Skyrmionelectronics: An overview and outlook. Proceedings of the IEEE 104, 2040–2061 (2016).

    CAS  Article  Google Scholar 

  13. 13.

    Kang, W. et al. Voltage controlled magnetic skyrmion motion for racetrack memory. Sci. Rep. 6, 23164 (2016).

    ADS  CAS  Article  Google Scholar 

  14. 14.

    Zang, J., Mostovoy, M., Han, J. H. & Nagaosa, N. Dynamics of skyrmion crystals in metallic thin films. Phys. Rev. Lett. 107, 136804 (2011).

    ADS  Article  Google Scholar 

  15. 15.

    Litzius, K. et al. Skyrmion Hall effect revealed by direct timeresolved x-ray microscopy. Nat. Phys. 13, 170–175 (2017).

    CAS  Article  Google Scholar 

  16. 16.

    Zhang, X. et al. Skyrmion-skyrmion and skyrmion-edge repulsions in skyrmion-based racetrack memory. Sci. Rep. 5, 7643 (2015).

    CAS  Article  Google Scholar 

  17. 17.

    Kim, K.-W., Moon, K.-W., Kerber, N., Nothhelfer, J. & Everschor-Sitte, K. Asymmetric skyrmion Hall effect in systems with a hybrid Dzyaloshinskii-Moriya interaction. Phys. Rev. B 97, 224427 (2018).

    ADS  CAS  Article  Google Scholar 

  18. 18.

    Büttner, F., Lemesh, I. & Beach, G. S. Theory of isolated magnetic skyrmions: From fundamentals to room temperature applications. Sci. Rep. 8, 4464 (2018).

    ADS  Article  Google Scholar 

  19. 19.

    Göbel, B., Mook, A., Henk, J. & Mertig, I. Overcoming the speed limit in skyrmion racetrack devices by suppressing the skyrmion Hall effect. Phys. Rev. B 99, 020405(R) (2019).

    ADS  Article  Google Scholar 

  20. 20.

    Barker, J. & Tretiakov, O. A. Static and dynamical properties of antiferromagnetic skyrmions in the presence of applied current and temperature. Phys. Rev. Lett. 116, 147203 (2016).

    ADS  Article  Google Scholar 

  21. 21.

    Zhang, X., Zhou, Y. & Ezawa, M. Magnetic bilayer-skyrmions without skyrmion Hall effect. Nature Commun. 7, 10293 (2016).

    ADS  CAS  Article  Google Scholar 

  22. 22.

    Zhang, X., Zhou, Y. & Ezawa, M. Antiferromagnetic skyrmion: stability, creation and manipulation. Sci. Rep. 6, 24795 (2016).

    ADS  CAS  Article  Google Scholar 

  23. 23.

    Göbel, B., Mook, A., Henk, J. & Mertig, I. Antiferromagnetic skyrmion crystals: Generation, topological Hall, and topological spin Hall effect. Phys. Rev. B 96, 060406(R) (2017).

    ADS  Article  Google Scholar 

  24. 24.

    Bogdanov, A. & Hubert, A. The stability of vortex-like structures in uniaxial ferromagnets. J. Magn. Magn. Mater. 195, 182–192 (1999).

    ADS  CAS  Article  Google Scholar 

  25. 25.

    Beg, M. et al. Ground state search, hysteretic behaviour, and reversal mechanism of skyrmionic textures in confined helimagnetic nanostructures. Sci. Rep. 5, 17137 (2015).

    ADS  Article  Google Scholar 

  26. 26.

    Zhang, X. et al. Control and manipulation of a magnetic skyrmionium in nanostructures. Phys. Rev. B 94, 094420 (2016).

    ADS  Article  Google Scholar 

  27. 27.

    Finazzi, M. et al. Laser-induced magnetic nanostructures with tunable topological properties. Phys. Rev. Lett. 110, 177205 (2013).

    ADS  CAS  Article  Google Scholar 

  28. 28.

    Zheng, F. et al. Direct imaging of a zero-field target skyrmion and its polarity switch in a chiral magnetic nanodisk. Phys. Rev. Lett. 119, 197205 (2017).

    ADS  Article  Google Scholar 

  29. 29.

    Zhang, S., Kronast, F., van der Laan, G. & Hesjedal, T. Real-space observation of skyrmionium in a ferromagnet-magnetic topological insulator heterostructure. Nano Lett. 18, 1057–1063 (2018).

    ADS  CAS  Article  Google Scholar 

  30. 30.

    Hagemeister, J., Siemens, A., Rózsa, L., Vedmedenko, E. Y. & Wiesendanger, R. Controlled creation and stability of kπ skyrmions on a discrete lattice. Phys. Rev. B 97, 174436 (2018).

    ADS  CAS  Article  Google Scholar 

  31. 31.

    Kolesnikov, A. G., Stebliy, M. E., Samardak, A. S. & Ognev, A. V. Skyrmionium–high velocity without the skyrmion Hall effect. Sci. Rep. 8, 16966 (2018).

    ADS  Article  Google Scholar 

  32. 32.

    Li, S. et al. Dynamics of a magnetic skyrmionium driven by spin waves. Appl. Phys. Lett. 112, 142404 (2018).

    ADS  Article  Google Scholar 

  33. 33.

    Shen, M., Zhang, Y., Ou-Yang, J., Yang, X. & You, L. Motion of a skyrmionium driven by spin wave. Appl. Phys. Lett. 112, 062403 (2018).

    ADS  Article  Google Scholar 

  34. 34.

    Pylypovskyi, O. V. et al. Chiral skyrmion and skyrmionium states engineered by the gradient of curvature. Phys. Rev. Appl. 10, 064057 (2018).

    ADS  CAS  Article  Google Scholar 

  35. 35.

    Yang, Y. et al. Ultrafast magnetization reversal by picosecond electrical pulses. Sci. Adv. 3, e1603117 (2017).

    ADS  Article  Google Scholar 

  36. 36.

    Slonczewski, J. C. Current-driven excitation of magnetic multilayers. J. Magn. Magn. Mater. 159, L1–L7 (1996).

    ADS  CAS  Article  Google Scholar 

  37. 37.

    Ketchen, M. et al. Generation of subpicosecond electrical pulses on coplanar transmission lines. Appl. Phys. Lett. 48, 751–753 (1986).

    ADS  Article  Google Scholar 

  38. 38.

    Landau, L. D. & Lifshitz, E. On the theory of the dispersion of magnetic permeability in ferromagnetic bodies. Phys. Z. Sowjetunion 8, 101–114 (1935).

    MATH  Google Scholar 

  39. 39.

    Gilbert, T. A Lagrangian formulation of the gyromagnetic equation of the magnetization field. Phys. Rev. 100, 1243 (1955).

    Google Scholar 

  40. 40.

    Fert, A., Cros, V. & Sampaio, J. Skyrmions on the track. Nature Nanotechnol. 8, 152–156 (2013).

    ADS  CAS  Article  Google Scholar 

  41. 41.

    Schäffer, A. F., Dürr, H. A. & Berakdar, J. Ultrafast imprinting of topologically protected magnetic textures via pulsed electrons. Appl. Phys. Lett. 111, 032403 (2017).

    ADS  Article  Google Scholar 

  42. 42.

    Schäffer, A. F., Dürr, H. A. & Berakdar, J. Ultrafast nanoscale magnetic switching via intense picosecond electron bunches. In Ultrafast Nonlinear Imaging and Spectroscopy V 10380, 103800G (2017).

    Google Scholar 

  43. 43.

    Thiele, A. Steady-state motion of magnetic domains. Phys. Rev. Lett. 30, 230 (1973).

    ADS  Article  Google Scholar 

  44. 44.

    Dzyaloshinsky, I. A thermodynamic theory of weak ferromagnetism of antiferromagnetics. J. Phys. Chem. Sol. 4, 241–255 (1958).

    ADS  CAS  Article  Google Scholar 

  45. 45.

    Moriya, T. Anisotropic superexchange interaction and weak ferromagnetism. Phys. Rev. 120, 91 (1960).

    ADS  CAS  Article  Google Scholar 

  46. 46.

    Schäffer, A. F., Rózsa, L., Berakdar, J., Vedmedenko, E. Y. & Wiesendanger, R. Stochastic dynamics and pattern formation of geometrically confined skyrmions. Commun. Phys.  2, 72 (2019).

  47. 47.

    Bruno, P., Dugaev, V. & Taillefumier, M. Topological Hall effect and Berry phase in magnetic nanostructures. Phys. Rev. Lett. 93, 096806 (2004).

    ADS  CAS  Article  Google Scholar 

  48. 48.

    Neubauer, A. et al. Topological Hall effect in the a phase of MnSi. Phys. Rev. Lett. 102, 186602 (2009).

    ADS  CAS  Article  Google Scholar 

  49. 49.

    Hamamoto, K., Ezawa, M. & Nagaosa, N. Quantized topological Hall effect in skyrmion crystal. Phys. Rev. B 92, 115417 (2015).

    ADS  Article  Google Scholar 

  50. 50.

    Göbel, B., Mook, A., Henk, J. & Mertig, I. Unconventional topological Hall effect in skyrmion crystals caused by the topology of the lattice. Phys. Rev. B 95, 094413 (2017).

    ADS  Article  Google Scholar 

  51. 51.

    Göbel, B., Mook, A., Henk, J. & Mertig, I. Signatures of lattice geometry in quantum and topological Hall effect. New J. Phys. 19, 063042 (2017).

    ADS  Article  Google Scholar 

  52. 52.

    Yin, G., Liu, Y., Barlas, Y., Zang, J. & Lake, R. K. Topological spin Hall effect resulting from magnetic skyrmions. Phys. Rev. B 92, 024411 (2015).

    ADS  Article  Google Scholar 

  53. 53.

    Landauer, R. Spatial variation of currents and fields due to localized scatterers in metallic conduction. IBM Journal of Research and Development 1, 223–231 (1957).

    MathSciNet  Article  Google Scholar 

  54. 54.

    Büttiker, M. Absence of backscattering in the quantum Hall effect in multiprobe conductors. Phys. Rev. B 38, 9375 (1988).

    ADS  Article  Google Scholar 

  55. 55.

    Vansteenkiste, A. & Van de Wiele, B. Mumax: a new highperformance micromagnetic simulation tool. J. Magn. Magn. Mater. 323, 2585–2591 (2011).

    ADS  CAS  Article  Google Scholar 

  56. 56.

    Vansteenkiste, A. et al. The design and verification of mumax3. AIP Adv. 4, 107133 (2014).

    ADS  Article  Google Scholar 

  57. 57.

    Simon, E., Rózsa, L., Palotás, K. & Szunyogh, L. Magnetism of a co monolayer on pt (111) capped by overlayers of 5 d elements: A spin-model study. Phys. Rev. B 97, 134405 (2018).

    ADS  CAS  Article  Google Scholar 

  58. 58.

    Tao, X. et al. Self-consistent determination of spin Hall angle and spin diffusion length in pt and pd: The role of the interface spin loss. Science Adv. 4, eaat1670 (2018).

    ADS  Article  Google Scholar 

  59. 59.

    Moreau-Luchaire, C. et al. Additive interfacial chiral interaction in multilayers for stabilization of small individual skyrmions at room temperature. Nature Nanotechnol. 11, 444 (2016).

    ADS  CAS  Article  Google Scholar 

  60. 60.

    Groth, C. W., Wimmer, M., Akhmerov, A. R. & Waintal, X. Kwant: a software package for quantum transport. New J. Phys. 16, 063065 (2014).

    ADS  Article  Google Scholar 

Download references


This work is supported by Priority Program SPP 1666, CRC/TRR 227 and SFB 762 of Deutsche Forschungsgemeinschaft (DFG).

Author information




B.G. and A.S. initiated research and planned the project. J.B., I.M. and S.P. supervised the project. B.G. conducted calculations of the topological Hall effect and analyzed the Thiele equation. A.S. did the micromagnetic simulations. B.G. and A.S. wrote the manuscript. All authors discussed the results and commented on the manuscript.

Corresponding authors

Correspondence to Börge Göbel or Alexander F. Schäffer.

Ethics declarations

Competing Interests

The authors declare no competing interests.

Additional information

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Göbel, B., Schäffer, A.F., Berakdar, J. et al. Electrical writing, deleting, reading, and moving of magnetic skyrmioniums in a racetrack device. Sci Rep 9, 12119 (2019). https://doi.org/10.1038/s41598-019-48617-z

Download citation

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing