# High Pressure Metamorphism Caused by Fluid Induced Weakening of Deep Continental Crust

## Abstract

Studies of mineral equilibria in metamorphic rocks have given valuable insights into the tectonic processes operating at convergent plate margins during an orogeny. Geodynamic models simulating orogenesis and crustal thickening have been constrained by temperature and pressure estimates inferred from the mineral assemblages of the various lithologies involved along with age constrains from increasingly precise geochronological techniques. During such studies it is assumed that the pressure experienced by a given rock is uniquely related to its depth of burial. This assumption has been challenged by recent studies of high pressure (HP) and ultrahigh pressure (UHP) rocks. Here, we describe an example of Caledonian HP metamorphism from the Bergen Arcs in western Norway, and show that the associated formation of Caledonian eclogites at the expense of Proterozoic granulites was related to local pressure perturbations rather than burial, and that the HP metamorphism resulted from fluid-induced weakening of an initially dry and highly stressed lower crust when thrust upon the hyperextended margin of the Baltic shield.

## Introduction

The last two decades of research have shown that prior to orogeny the lower continental crust is dry and mechanically strong1,2,3. When subject to an orogenic event, lower crustal lithologies commonly experience retrogressive metamorphism along faults and shear zones. The mineralogy of the associated product rocks reflects a large variation in temperature and pressure conditions ranging from eclogite facies to amphibolite facies assemblages4,5,6. Retrogressive metamorphism is invariably associated with the formation of hydrous minerals and often also carbonates, and both the mineralogical change and the frequently associated grain size reduction lead to a substantial reduction in rock strength. A pronounced mechanical weakening is reflected by the ductile behaviour of the shear zones in which these rocks are found. Such observations inspired early models of the lithosphere such as the ‘jelly-sandwich’ model7 where the lower crust is assumed to be wet and mechanically weak, and hence plate tectonic stress would be transmitted through the brittle upper crust and a strong upper mantle lithosphere.

Today, an increasing number of studies and observations indicates that structural and metamorphic transformation of initially dry lower crust involves an early stage of seismic failure6,8,9,10. Metamorphism and shear zone development then follow in the wake of lower crustal earthquakes. Hence the lower crust is subject to high differential stress prior to the production of weak rocks in shear zones11.

In the following, we present observations from the Bergen Arcs in western Norway where fluid induced retrogression of lower crustal granulites followed initial seismic faulting. Retrogression produced both eclogite facies and amphibolite facies lithologies, which then became loci of shear zone development. Through a simple force balance model, which is supported by 2D analytical stress-field calculations, we demonstrate that the formation of weak domains in a highly stressed lower crust will lead to significant pressure perturbations. We show that rheology-induced pressure increases to eclogite facies conditions above 2 GPa are consistent with the pressure-temperature-time history experienced by this crustal volume without invoking tectonic burial beyond ca 55 km depth. Hydration and seismic deformation continued during uplift to depths of ca 35 km, where amphibolite facies metamorphism associated with late pegmatite intrusions occurred near 600 °C at 423.6 ± 1 Ma, some 5 million years after eclogite formation.

## Geological Setting of the Bergen Arcs

The Lindås Nappe in the Bergen Arcs is composed of granulite facies remnants of Proterozoic lower crust belonging to the former Jotun-Lindås microcontinent (Fig. 1). Before the Caledonian plate convergence, the Jotun-Lindås microcontinent was separated from the margin of Baltica by a hyperextended domain with transitional thinned crust (<10 km), exhumed meta-peridotites, and extensional allochthons of continental crust12. The profile in Fig. 1 illustrates the tectonic setting in the Middle Silurian, at approximately 430 Ma. At this initial stage of the Scandian collision, ophiolites and Laurentian island-arc complexes were emplaced onto the Jotun-Lindås microcontinent and its fossiliferous Middle Silurian cover13. These events caused fluid-induced metamorphism transforming the 930 Ma old anhydrous granulite facies mineralogy14 to eclogites and amphibolites in shear zones, breccias and along fractures located near the leading edge of this microcontinent. The eclogites and amphibolites are now exposed on Holsnøy Island (Fig. S1). The hyperextended Baltic margin closed during the collision, which continued into the Lower Devonian and resulted in large-scale nappe translation (>600 km) onto Baltica and formation of a Himalayan-type mountain belt. The regional (U)HP metamorphism and metamorphic zonation in the Western Gneiss Complex at 410 ± 10 Ma (see inset map in Fig. 1) formed during the terminal stages of the collision15,16.

On the island of Holsnøy (Fig. S1b), pseudotachylytes, fine-grained or glassy fault rocks believed to reflect earthquake related frictional melting, are abundant on faults where the granulite facies rocks experienced Caledonian metamorphism. Such faults show single rupture displacements of up to 1.7 m10. The fault wall rocks display intense fragmentation often without significant shear strain, followed by healing processes through grain growth and formation of eclogite or amphibolite facies minerals, including hydrous phases such as amphibole, micas and clinozoisite8,17. Infiltration of hydrous fluids was thus directly associated with the seismic slip.

A significant rheological weakening associated with formation of the fine-grained and hydrous eclogites and amphibolites led to development of ductile shear zones in areas initially deformed by brittle failure (Fig. S2a,b). Relict pseudotachylytes can locally be observed ‘floating’ in the shear zones, providing unambiguous evidence for ductile deformation predated by brittle failure of granulite facies rocks10. All rock units are locally cut by pegmatitic veins (Fig. S2c,e). When these cut the original granulite, they are often rimmed by a cm to dm wide selvage of amphibolite facies rocks (Fig. S2d) attesting to the introduction of hydrous fluids and associated retrograde metamorphism.

## Conditions and Timing of Shear Zone Development

Early estimates of the conditions of eclogitization in shear zones were in the range 650–750 °C and 1.5–2.1 GPa18,19, while late amphibolite facies retrogression were reported to occur at significantly lower pressures at ca 600 °C and 0.8–1.0 GPa19. Recently, Bhowany et al.20, reported that seismic faulting occurred near 680 °C, 1.5–1.6 GPa, i.e. at amphibolite facies conditions where plagioclase was still stable. This is consistent with a detailed description of fault wall rock alteration reported by Petley-Ragan et al.17. Peak eclogite facies metamorphism, however, was interpreted to occur at similar temperatures, but at significantly higher pressure (2.1–2.2 GPa20). This was assumed to imply continued burial of the crustal volume after the stage of seismic deformation. Finally, retrogressed eclogite was reported to form at pressures near 1.6–1.7 GPa, still at approximately the same temperature.

To extend the results of Bhowany et al.20, we have performed phase diagram analysis (Methods) of the amphibolite facies mineral assemblage that developed around late stage feldspar rich pegmatites which cut both eclogite and amphibolite facies shear zones (Figs S2c,d and S3). In addition, we have constrained the pressure-temperature stability of mineral assemblages formed in a pseudotachylyte vein with an amphibolite facies mineral assemblage developed along a large displacement (1.7 meter) fault in an area with abundant amphibolite facies shear zones (Fig. S4). The results are shown in Fig. 2. For a pure H2O-fluid, the mineral assemblage in the amphibolite developed around the pegmatite is only stable in a very narrow domain of the pressure-temperature space, and puts narrow limits on the pressure and temperature conditions of formation near 600 °C and 1.05 GPa (Fig. 2a). This is in agreement with previous estimates of the conditions of amphibolitization at Holsnøy19. The mineral assemblage of the pseudotachylite in the large displacement fault is not very sensitive to temperature. However, both the mineral assemblage and the composition of the garnet present are consistent with formation at similar conditions near 1 GPa and 600 °C (Fig. 2b).

To constrain the age of the latest stage of amphibolitisation, U-Pb geochronology (see Methods for analytical details) was carried out on an albite-, muscovite-, biotite-, kyanite-, amphibole-bearing pegmatite. These are common at Holsnøy and crosscut both eclogite- and amphibolite facies shear zones. Zircon is relatively abundant in the sample, along with rutile and apatite. It occurs as colourless, equant fragments, locally exhibiting crystal faces, and in minor amounts as euhedral, equant to very short prismatic grains. Inclusions of other minerals, mainly feldspar, are common. Cathodoluminescence images reveal a faint but distinct regular growth zoning and also local zones of reworking with fracturing and recrystallization or overgrowths (Fig. 3).

The zircons are extremely low in U, ranging from 1.2 to 3.1 ppm, and Th/U ~ 0 (Table S1). Consequently, only little Pb was available (<0.2 ppm) for the measurements and initial attempts using single grains were not successful. Six analyses based on fractions of 3 to 8 grains are clustered to the right of the Concordia curve. Given the low amount of U, and the fact that they all underwent chemical abrasion, it is unlikely that the discordance is due to Pb loss. It may instead be the result of small excesses of initial 231Pa. The analyses yield overlapping 206Pb/238U ages with an average of 423.6 ± 1.0 Ma (Fig. 3). This pegmatite age overlaps with previous age determinations on eclogites from Holsnøy by Glodny et al.21(422 ± 10 Ma by the Sm-Nd methods, and 425 ± 4 by the Rb-Sr method), and Bingen et al.22, (423 ± 4 by U-Pb), but is slightly younger than the U-Pb age obtained by Glodny et al.23 (429 ± 3 Ma). The amphibolite facies metamorphism has previous been assumed to occur at 410–415 Ma based on Rb-Sr data23. An older U-Pb age (427.4 ± 0.9 Ma) from an amphibolite facies assemblage23 was interpreted to represent inherited zircons from eclogite facies rocks. Our new data for the last phase of amphibolitisation indicate that the age of the lower-pressure assemblage was much closer to the high-pressure stage than previously assumed, possibly nearly coeval. However, our phase diagram analysis indicates that the amphibolite facies assemblages that developed around the late pegmatites formed at 50–100 °C lower temperatures than the eclogites and thus appear to have formed later, after a period of pressure reduction and cooling.

## Weakening Induced Pressure Effects

Thermo-mechanical numerical simulations of continental lithosphere shortening showed that the development of a weak shear zone within a stressed lower crust can generate a significant pressure increase inside the shear zone as the corresponding differential stress decreases24. This pressure increase results from the force balance across the shear zone and can be explained with a conceptual Mohr circle diagram that is based on a 2D analytical solution for a stressed body, or matrix, with a weak elliptical inclusion (Fig. 4; Moulas et al.25). The inclusion mimics the shear zone. The force balance between inclusion and matrix requires that the total stress normal to the inclusion-matrix interface must be identical in the inclusion and the matrix (Fig. 4a). The total stress is the sum of the pressure and the deviatoric stress. To illustrate the stress state, we consider a configuration where there is only normal stress acting on the inclusion-matrix interface and the shear stress is zero (Fig. 4a and black dot in b). For such configuration the deviatoric stress is half the differential stress. Since the deviatoric stress is smaller in the weak inclusion than in the strong matrix, the pressure in the weak inclusion must be correspondingly larger than the one in the matrix to obtain the same total stress (Fig. 4). The pressure variation depends on the aspect ratio of the inclusion and its orientation with respect to the applied differential stress25. Thus, some weak inclusions will develop a significant pressure increase, while others will not. The analytical results are valid for both viscous and elastic materials (Fig. 4b and c; Moulas et al.25,26).

When applied to the observed eclogite shear zones in the Bergen Arc granulites, the above mechanical models can explain the recorded pressure variations in the following steps: First, the granulite is under sufficient differential stress to cause seismic failure (≥1 GPa10). Second, fracturing of the granulite allows inflow of fluids. Third, the fluids cause metamorphic reactions and the reacting granulite weakens mechanically. The geometry of the weakened regions is controlled by the geometry of the fractures and can be described as elliptical regions in 2D (Fig. 4b). Depending on the orientation and aspect ratio of the weakened regions (see Moulas et al.25) the pressure can rise locally. The magnitude of the pressure rise is evaluated in the following (Fig. 4b and c).

The absolute magnitude of the pressure in the granulite is $${P}_{G}=\frac{{\sigma }_{1}+{\sigma }_{2}+{\sigma }_{3}}{3}$$, where σ1, σ2 and σ3 are the principal stresses. The differential stress, σ1 − σ3, in the weak product rocks will be significantly smaller than in the strong granulite, and the pressure in the product (PE) is close to the maximal principal stress, σ1, in the granulite (Fig. 4a). The force balance requires that the two Mohr circles for granulite and weak product rocks must touch at one point. In the presented example both Mohr circles touch at the main principal stress (σ1) of the granulite. The value of σ1 − σ3 in the granulite required to cause a pressure perturbation, $${\rm{\Delta }}P={P}_{E}-{P}_{G}\approx {\sigma }_{1}-{P}_{G}$$, between granulite and eclogite depends on the value of σ2, the principal stress in the third, out-of-plane direction. Assuming $${\sigma }_{2}\approx {\sigma }_{3}$$ provides the relationship

$${\sigma }_{1}-{\sigma }_{3}\approx \frac{3}{2}{\rm{\Delta }}P.$$

Assuming $${\sigma }_{2}\approx ({\sigma }_{1}+{\sigma }_{3})/2$$ yields

$${\sigma }_{1}-{\sigma }_{3}\approx 2{\rm{\Delta }}P.$$

Hence, a pressure perturbation of 0.5 GPa requires a differential stress between 0.75 and 1.0 GPa depending on σ2 (Fig. 4b and c). These differential stresses approach the frictional strength of compressed continental rocks at depths between 20 and 30 km (e.g. Kohlstedt et al.27). Rock deformation experiments suggest that the transition from semi-brittle deformation to fully plastic (or viscous creep) deformation occurs when the differential stress is equal to the effective confining pressure of the rock (the so-called Goetze’s criterion27). Assuming that the effective confining pressure in the granulite is close to the metamorphic pressure estimate for the recrystallized pseudotachylites (1.5 GPa20), indicates that differential stresses exceeding 1.0 GPa for semi-brittle deformation are feasible in the granulite. Hence, both the rock’s frictional strength and the stress magnitudes required for the onset of plastic deformation support differential stresses near 1.0 GPa in the granulite. It is thus feasible to generate pressure perturbations exceeding 0.5 GPa in the weak rock when embedded in a strong granulite under high differential stress. The pressure difference between the mineral assemblage described as recrystallized pseudotachylite (1.5–1.6 GPa20) and the peak eclogite facies metamorphism (2.1–2.2 GPa20) may thus be due to the excess pressure generated by weakening of shear zone rocks following hydration without the need of further burial to >70 km depth.

## Discussion

In the tectonic scenario presented in Fig. 1, Caledonian eclogite-forming metamorphism of the Proterozoic granulites of the Bergen Arcs took place as the Jotun-Lindås nappe was thrust upon the hyperextended margin of Baltica and contemporaneously overthrust by nappes of oceanic affinity (Fig. 1). In this scenario, the rocks in which amphibolites and eclogites formed at 423–429 Ma, were probably never buried to Himalaya-like depth (twice the normal continental crust) and never experienced conditions corresponding to lithostatic pressures above ca. 1.5 GPa. This is furthermore broadly consistent with the density of fluid inclusions occurring in felsic extension veins interpreted to have formed during eclogitization28.

Mineral assemblages indicate an isothermal pressure increase of >0.5 GPa following seismic failure20 and a subsequent decrease by ca. 1.0 GPa towards amphibolite facies conditions (Fig. 2). Assuming an average rock density of 2900 kg/m3 a lithostatic pressure >0.5 GPa corresponds to a depth >18 km from an initial depth of ca 50–55 km. This is not consistent with the tectonic scenario shown in Fig. 1. Moreover, the lowest thermal gradients considered reasonable for subduction zones are ca. 5 °C/km (e.g. Syracuse et al.29; Penniston-Dorland et al.30). Hence, a >18 km depth increase by burial due to subduction should correspond to a temperature increase of >90 °C. Therefore, an isothermal pressure increase of >0.5 GPa due to burial by subduction is thermo-mechanically not feasible and calls for alternative mechanisms.

Moreover, the entire metamorphic history from the initiation by seismic failure and eclogite formation in shear zones to the intrusion of tonalitic pegmatites, with an amphibolite facies selvage formed at ca. 600 °C, 0.8–1 GPa, took place within 5 million years or less. Isothermal subduction from 50 to >70 km, followed by near isothermal exhumation to ca 55 km depth, and finally return to less than 35 km depth within this time interval does not seem feasible for the relevant tectonic scenario.

The alternative model that we propose here is that a local weakening of dry and highly stressed lower crust naturally leads to pressure perturbations of the magnitude observed here. This will apply to any convergent plate boundary where seismic activity and associated fluid introduction leads to weakening of lower crustal volumes10. The magnitude of the pressure perturbation will depend on the initial stress level, the local geometric constraints and the magnitude of the weakening. For a given field area, one would expect to see a variety of pressure conditions recorded by the more or less synchronously developed hydrated product rocks. Eclogite facies shear zones may thus exist essentially side-by-side with amphibolite facies shear zones developed at the same depth and temperature conditions.

In the Bergen Arcs case, many lines of evidence indicate that eclogite facies metamorphism is not necessarily the result of deep burial of continental material, but rather to local fluid induced weakening of initially highly stressed dry granulites. Since the lower continental crust is expected to be both dry and strong prior to an orogenic event3 and earthquake induced fluid introduction with associated metamorphic weakening processes seems to be common during orogeny, weakening induced pressure perturbations in the lower crust will also be common during orogenic events. This may explain a number of enigmatic observations of contrasting PT estimates from lower crustal lithologies undergoing retrogressive metamorphism.

Finally, the presence of pseudotachylytes recrystallized under pressures as low as 1 GPa, illustrates that seismic deformation was not confined to a fixed event prior to eclogite facies pressure conditions, but likely occurred throughout the metamorphic history of this lower crustal volume.

## Methods

### Calculation of P-T sections

For the calculation of the P-T section of the amphibolite we performed Gibbs free energy minimization31,32 using Perple_X (http://www.perplex.ethz.ch). We considered the following solution models Bio(TCC) for biotite33, cAmph(DP) for clinoamphibole34, Mica(CHA1) for white mica35,36, feldspar for potassium feldspar and plagioclase37, Gt(GCT) for garnet38, Chl(HP) for chlorite39, Omph(GHP) for clinopyroxene34,40 and IlGkPy for ilmenite (ideal). We considered the K2O-Na2O-CaO-FeO-MgO-Al2O3-SiO2-TiO2-H2O model system and the thermodynamic database of Holland and Powell41,42. The mineral abbreviations are after Siivola and Schmid43. The bulk composition that was used is (in wt%): K2O: 0.53; Na2O: 2.15; CaO: 12.68; FeO: 6.96; MgO: 8.47; Al2O3: 20.90; SiO2: 43.86; TiO2: 0.40; H2O: saturated.

The same method was employed for the calculation of various P-CO2 sections for the pseudotachylite. The different sections were calculated at 620, 650, 670, 700, 720, and 750 C. Dolomite was modelled using the oCcM(HP) solid solution41. The bulk composition that was used is (in wt%): K2O: 0.8; Na2O: 3.36; CaO: 10.38; FeO: 3.83; MgO: 3.84; Al2O3: 24.72; SiO2: saturated. The total H2O and CO2 was constrained from the amount of LOI.

#### U-Pb analysis

After crushing and various conventional concentration steps, the zircon grains were selected under a binocular microscope and subsequently subjected to chemical abrasion44. This was followed by spiking with a 202Pb-205Pb-235U tracer, dissolution, chemical isolation of U and Pb with ion exchange resin, and mass spectrometry, after the procedure of Krogh45 with modifications described in Corfu46. Most of the measurements were performed with an ion counting secondary electron multiplier, correcting the Pb fractionation with the 205Pb/202Pb ratio of the spike and U with 0.12%/amu. Blank corrections were 0.1 pg for U and ≤2 pg Pb. Any remaining initial Pb was corrected using compositions calculated with the model of Stacey and Kramers47. The tracer is calibrated against the ET100 solution (Condon, pers. comm). Plotting and regressions were done with the Isoplot software package48. The decay constants are those of Jaffey et al.49.

## Data Availability

All of the data used are contained within the paper.

## References

1. 1.

Yardley, B. W. D. & Valley, J. W. The petrologic case for a dry lower crust. Journal of Geophysical Research 102, 12173–12185 (1997).

2. 2.

Jackson, J. A., Austrheim, H., McKenzie, D. & Priestley, K. Metastability, mechanical strength, and the support of mountain belts. Geology 32, 625–628 (2004).

3. 3.

Jamtveit, B., Austrheim, H. & Putnis, A. Disequilibrium metamorphism of stressed lithosphere. Earth-Science Reviews 154, 1–13 (2016).

4. 4.

Austrheim, H. Eclogitization of lower crustal granulites by fluid migration through shear zones. Earth and Planetary Science Letters 81, 221–232 (1987).

5. 5.

Kullerud, K., Flaat, K. & Davidsen, B. High-pressure fluid-rock reactions involving Cl-bearing fluids in lower-crustal ductile shear zones of the Flakstadoy basic complex, Lofotem, Norway. Journal of Petrology 42, 1349–1372 (2001).

6. 6.

Menegon, L., Pennachioni, G., Malaspina, N., Harris, K. & Wood, E. Earthquakes as precursors of ductile shear zones in the dry and strong lower crust. Geochemistry, Geophysics and Geosystems 18, 4356–4374 (2017).

7. 7.

Chen, W. P. & Molnar, P. Focal depths of intracontinental and intraplate earthquakes and their implication for the thermal and mechanical properties of the lithosphere. Journal of Geophysical Research 88, 4183–4214 (1983).

8. 8.

Austrheim, H. et al. Microstructural records of seismic slip. Science Advances 3, e1602067 (2017).

9. 9.

Putnis, A., Jamtveit, B. & Austrheim, H. Metamorphic processes and seismicity: the Bergen Arcs as a natural laboratory. Journal of Petrology 58, 1871–1898 (2017).

10. 10.

Jamtveit, B., Ben-Zion, Y., Renard, F. & Austrheim, H. Earthquake-induced transformation of the lower crust. Nature 556, 487491 (2018).

11. 11.

Andersen, T. B., Mair, K., Austrheim, H., Podladchikov, Y. Y. & Vrijmoed, J. C. Stress-release in exhumed intermediate-deep earthquakes determined from ultramafic pseudotachylyte. Geology 36(12), 995–998 (2008).

12. 12.

Jakob, J., Alsaif, M., Corfu, F. & Andersen, T. B. Age and origin of thin discontinuous gneiss sheets in the distal domain of the magma-poor hyperextended pre-Caledonian margin of Baltica, Southern Norway. Journal of the Geological Society of London 174, 541–571 (2017).

13. 13.

Andersen, T. B. & Jamtveit, B. Uplift of deep crust during orogenic extensional collapse. A model based on field studies in the Sogn-Sunnfjord Region of W.Norway. Tectonics 9, 1097–1111 (1990).

14. 14.

Bingen, B., Davis, W. J. & Austrheim, H. Zircon U-Pb geochronology in the Bergen arc eclogites and their Proterozoic protoliths, and implications for the pre-Scandian evolution of the Caledonides in western Norway. Geological Society of America Bull. 113, 640–649 (2001).

15. 15.

Andersen, T. B., Jamtveit, B., Dewey, J. F. & Swensson, E. Subduction and eduction of continental crust; major mechanisms during continent-continent collision and orogenic extensional collapse. Terra Nova 3, 303–310 (1991).

16. 16.

Hacker, B. R. et al. High-temperature deformation during continental margin subduction and exhumation: The Ultrahigh-Pressure Western Gneiss Region of Norway. Tectonophysics 480, 149–171 (2010).

17. 17.

Petley-Ragan, A., Dunkel, K. G., Austrheim, H., Ildefonse, B. & Jamtveit, B. Microstructural records of intermediate-depth earthquakes and associate fluid- driven metamorphism of plagioclase-rich granulites. Journal of Geophysical Research 123, 3729–3746 (2018).

18. 18.

Jamtveit, B., Bucher-Nurminen, K. & Austrheim, H. Fluid controlled eclogitization of granulites in deep crustal shear zones, Bergen Arcs, western Norway. Contributions to Mineralogy and Petrology 104, 184–193 (1990).

19. 19.

Kühn, A. The influence of fluid on the granulite to eclogite and amphibolite facies transition: a study in the anorthositic rocks from the Lindås Nappe, Bergen Arcs, West Norway. PhD Thesis, University of Oslo (2002).

20. 20.

Bhowany, K. et al. Phase equilibria modeling constraints on P-T conditions during fluid catalyzed conversion of granulite to eclogite in the Bergen Arcs, Norway. Journal of Metamorphic Geology 36, 315–342 (2018).

21. 21.

Glodny, J., Kühn, A. & Austrheim, H. Rb/Sr record of fluid–rock interaction in eclogites, Bergen Arcs, Norway. Geochim. Cosmochim. Acta 66(S1), A280 (2002).

22. 22.

Bingen, B., Austrheim, H., Whitehouse, M. J. & Davies, W. J. Trace element signature and U-Pb geochronology of eclogite-facies zircon, Bergen Arcs, Caledonides of W Norway. Contributions to Mineralogy and Petrology 147, 671–683 (2004).

23. 23.

Glodny, J., Kühn, A. & Austrheim, H. Geochronology of fluid-induced eclogite and amphibolite facies metamorphic reactions in a subduction-collision system, Bergen Arcs, Norway. Contributions to Mineralogy and Petrology 156, 27–48 (2008).

24. 24.

Schmalholz, S. M. & Podladchikov, Y. Y. Tectonic overpressure in weak crustal-scale shear zones and implications for the exhumation of high-pressure rocks. Geophysical Research Letters 40, 1984–1988 (2013).

25. 25.

Moulas, E., Burg, J. P. & Podladchikov, Y. Y. Stress field associated with elliptical inclusions in a deforming matrix: Mathematical model and implications for tectonic overpressure in the lithosphere. Tectonophysics 631, 37–49 (2014).

26. 26.

Moulas, E. et al. Relation between stress, thermodynamic and lithostatic pressure. Journal of metamorphic geology, https://doi.org/10.1111/jmg.12446 (2018).

27. 27.

Kohlstedt, D. L., Evans, B. & Mackwell, S. J. Strength of the lithosphere – constraints imposed by laboratory experiments. J. Geophysical Research 100, 17587–17602 (1995).

28. 28.

Andersen, T., Austrheim, H. & Burke, E. A. J. Melt-fluid-mineral interactions in high-pressure shear zones in the Bergen Arcs nappe complex, Caledonides of W. Norway: Implications for the fluid regime in Caledonian eclogite-facies metamorphism. Lithos 27, 187–204 (1991).

29. 29.

Syracuse, E. M., van Keken, P. E. & Abers, G. A. The global range of subduction zone thermal models. Physics of the Earth and Planetary Interiors 183, 73–90 (2010).

30. 30.

Penniston-Dorland, S. C., Kohn, M. J. & Manning, C. E. The global range of subduction zone thermal structure from exhumed blueschists and eclogites: Rocks are hotter than models. Earth and Planetary Science Letters 428, 243–254 (2015).

31. 31.

Connolly, J. A. D. The geodynamic equation of state: What and how. Geochem. Geophys.Geosystems 10, Q10014 (2009).

32. 32.

Connolly, J. A. D. Computation of phase equilibria by linear programming: A tool for geodynamic modeling and its application to subduction zone decarbonation. Earth and Planetary Science Letters 236, 524–541 (2005).

33. 33.

Tajčmanová, L., Connolly, J. A. D. & Cesare, B. A thermodynamic model for titanium and ferric iron solution in biotite. J. Metamorphic Geology 27, 153–165 (2009).

34. 34.

Diener, J. F. A. & Powell, R. Revised activity–composition models for clinopyroxene and amphibole. J. Metamorphic Geology 30, 131–142 (2012).

35. 35.

Coggon, R. & Holland, T. J. B. Mixing properties of phengitic micas and revised garnet-phengite thermobarometers. J. Metamorphic Geology 20, 683–696 (2002).

36. 36.

Auzanneau, E., Schmidt, M. W., Vielzeuf, D. & Connolly, J. A. D. Titanium in phengite: a geobarometer for high temperature eclogites. Contributions to Mineralogy and Petrology 159, 1–24 (2010).

37. 37.

Newton, R. C., Charlu, T. V. & Kleppa, O. J. Thermochemistry of the high structural state plagioclases. Geochimica et Cosmochimica Acta 44, 933–941 (1980).

38. 38.

Ganguly, J., Cheng, W. & Tirone, M. Thermodynamics of aluminosilicate garnet solid solution: new experimental data, an optimized model, and thermometric applications. Contributions to Mineralogy and Petrology 126, 137–151 (1996).

39. 39.

Holland, T. J. B., Baker, J. & Powell, R. Mixing properties and activity-composition relationships of chlorites in the system MgO-FeO-Al2O3-SiO2-H2O. European J. Mineralogy 10, 395–406 (1998).

40. 40.

Green, E., Holland, T. & Powell, R. An order disorder model for omphacitic pyroxenes in the system jadeite diopside hedembergite acmite, with applications to eclogitic rocks. American Mineralogist. 92, 1181–1189 (2007).

41. 41.

Holland, T. J. B. & Powell, R. An internally consistent thermodynamic data set for phases of petrological interest. J. Metamorphic Geology 16, 309–343 (1998).

42. 42.

Holland, T. J. B. & Powell, R. Activity-composition relations for phases in petrological calculations: an asymmetric multicomponent formulation. Contributions to Mineralogy and Petrology 145, 492–501 (2003).

43. 43.

Siivola, J. & Schmid, R. A systematic nomenclature for metamorphic rocks 12. List of mineral abbreviations. Recommendations by the IUGS Subcommission on the Systematics of Metamorphic Rocks (2007).

44. 44.

Mattinson, J. M. Zircon U-Pb chemical abrasion (“CA-TIMS”) method: combined annealing and multi-step partial dissolution analysis for improved precision and accuracy of zircon ages. Chemical Geology 220, 47–66 (2005).

45. 45.

Krogh, T. E. A low-contamination method for hydrothermal decomposition of zircon and extraction of U and Pb for isotopic age determinations. Geochimica et Cosmochimica Acta 37, 485–494 (1973).

46. 46.

Corfu, F. U-Pb age, setting and tectonic significance of the anorthosite–mangerite–charnockite–granite suite, Lofoten–Vesterålen, Norway. Journal of Petrology 45, 1799–1819 (2004).

47. 47.

Stacey, J. S. & Kramers, J. D. Approximation of terrestrial lead isotope evolution by a two-stage model. Earth and Planetary Science Letters 26, 207–221 (1975).

48. 48.

Jaffey, A. H., Flynn, K. F., Glendenin, L. E., Bentley, W. C. & Essling, A. M. Precision measurement of half-lives and specific activities of U 235 and U 238. Physical Review C 4, 1889 (1971).

49. 49.

Ludwig, K. R. Isoplot 4.1. A geochronological toolkit for Microsoft Excel. Berkeley Geochronology Center Special Publication 4, 76 (2009).

## Acknowledgements

This project was supported by the European Union’s Horizon 2020 Research and Innovation Programme under the ERC Advanced Grant Agreement n°669972, ‘Disequilibrium Metamorphism’ (‘DIME’) to BJ and the RCN CoE-grant 223272 to CEED (TBA). This paper benefitted from a discussion with Neil Mancktelow during the 2017 EGU meeting, from frequent discussions with Andrew Putnis, and constructive suggestions by two anonymous reviewers.

## Author information

Authors

### Contributions

B.J., E.M. and S.M.S. designed this study; B.J. wrote the manuscript with input from S.M.S., E.M. and T.B.A.; H.A., T.B.A., A.P.-R. and B.J. conducted the field studies; A.P.-R. and B.J. did the petrographic studies; F.C. did the U-Pb chronology; E.M. constructed the P-T sections, and E.M. and S.M.S. produced the force balance model.

### Corresponding author

Correspondence to Bjørn Jamtveit.

## Ethics declarations

### Competing Interests

The authors declare no competing interests.

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

## Rights and permissions

Reprints and Permissions

Jamtveit, B., Moulas, E., Andersen, T.B. et al. High Pressure Metamorphism Caused by Fluid Induced Weakening of Deep Continental Crust. Sci Rep 8, 17011 (2018). https://doi.org/10.1038/s41598-018-35200-1

• Accepted:

• Published:

• ### Microstructurally controlled trace element (Zr, U–Pb) concentrations in metamorphic rutile: An example from the amphibolites of the Bergen Arcs

• Jo Moore
• , Andreas Beinlich
• , Jennifer K. Porter
• , Cristina Talavera
• , Jasper Berndt
• , Sandra Piazolo
• , Håkon Austrheim
•  & Andrew Putnis

Journal of Metamorphic Geology (2020)

• ### Deep infiltration of surface water during deformation? Evidence from a low- δ18O shear zone at Koegel Fontein, Namaqualand, South Africa

• , Chris Harris
•  & R. Alastair Sloan

Lithos (2020)

• ### Zircon and quartz inclusions in garnet used for complementary Raman thermobarometry: application to the Holsnøy eclogite, Bergen Arcs, Western Norway

• Xin Zhong
• , Niels H. Andersen
• , Marcin Dabrowski
•  & Bjørn Jamtveit

Contributions to Mineralogy and Petrology (2019)

• ### The Interplay of Eclogitization and Deformation During Deep Burial of the Lower Continental Crust—A Case Study From the Bergen Arcs (Western Norway)

• Sascha Zertani
• , Loic Labrousse
• , Timm John
• , Torgeir B. Andersen
•  & Frederik Tilmann

Tectonics (2019)

• ### Metamorphic pressure variation in a coherent Alpine nappe challenges lithostatic pressure paradigm

• Cindy Luisier
• , Lukas Baumgartner
• , Stefan M. Schmalholz
• , Guillaume Siron
•  & Torsten Vennemann

Nature Communications (2019)