Localising functionalised gold-nanoparticles in murine spinal cords by X-ray fluorescence imaging and background-reduction through spatial filtering for human-sized objects

Abstract

Accurate in vivo localisation of minimal amounts of functionalised gold-nanoparticles, enabling e.g. early-tumour diagnostics and pharmacokinetic tracking studies, requires a precision imaging system offering very high sensitivity, temporal and spatial resolution, large depth penetration, and arbitrarily long serial measurements. X-ray fluorescence imaging could offer such capabilities; however, its utilisation for human-sized scales is hampered by a high intrinsic background level. Here we measure and model this anisotropic background and present a spatial filtering scheme for background reduction enabling the localisation of nanoparticle-amounts as reported from small-animal tumour models. As a basic application study towards precision pharmacokinetics, we demonstrate specific localisation to sites of disease by adapting gold-nanoparticles with small targeting ligands in murine spinal cord injury models, at record sensitivity levels using sub-mm resolution. Both studies contribute to the future use of molecularly-targeted gold-nanoparticles as next-generation clinical diagnostic and pharmacokinetic tools.

Introduction

Therapeutic approaches to pathological disorders would benefit strongly from high-resolution/high-sensitivity in vivo imaging and/or pharmacokinetic information. There has been a tremendous surge in both molecularly-targeted probe and device technologies for nanomedicine, which promise to enable earlier, more sensitive and precise detection for various pathologies1,2,3,4. For example, as a result of the aging of the human population, cancer is the most common cause of death worldwide, and secondary prevention methods, directed at early cancer/metastases detection, will improve the likelihood of successful therapy and higher survival rates5. Another opportunity to foster the development of targeted therapy is in vivo tracking of medical drugs through the body, based e.g. on antibody reactions, i.e. pharmacokinetic (PK) studies6,7,8.

One such promising non-invasive imaging solution is based on X-ray fluorescence imaging (XFI) of gold-nanoparticles (GNPs), which are either functionalised (for diagnostics and image-guided radiotherapy) or bound to medical drugs (for PK). The method presented here is expected to offer effectively higher detection sensitivity than Magnetic Resonance Imaging (MRI) as XFI signals only arise from GNP-localisation, are robust against physiological inhomogeneity, and do not require a pre-contrast-injection measurement. The spatial resolution of XFI achievable for human use is in the range of 1 mm or below, defined solely by the applied X-ray pencil beam diameter. This resolution is roughly equivalent to that offered by clinical MRI, but higher than that associated with clinical Positron Emission Tomography (PET) scanners; the latter modality has a typical clinical resolution of 4–5 mm. A key advantage of XFI over PET can be seen in the possibility to frequently monitor response assessments over arbitrarily long time periods at low cumulated doses, whereas these conditions would not be practically achievable with PET imaging, given the typically short physical half-lives of radiotracers and the associated higher costs of these studies. In addition, PET is hardly suitable for imaging on short time-scales (below minutes) for large investigation areas due to noise limitations.

The in vivo localisation of GNPs, however, depends on the unambiguous detection of emitted X-ray fluorescence photons following excitation with incident X-ray photons. The challenge is to provide sufficiently high sensitivity to detect and quantitate very low GNP-amounts within target tumour tissues and other critical organs, particularly at sufficient in vivo penetration depths. To achieve this, two independent challenges, both addressed by this work, have to be met, enabling successful deployment of XFI as a clinical tool: (i) the effective surface-functionalisation of GNPs to target disease and (ii) a dedicated scheme needed to distinguish emitted fluorescence X-ray photons from the vast number of background photons, especially in case of large objects. Although the XFI-approach has been under investigation for quite some time9,10,11,12,13,14,15, most approaches still suffer from this intrinsic “background problem” for human-sized objects at tolerable dose-levels, when the GNP-amounts are as low as expected for clinical applications and/or reported from small-animal studies.

We address the sensitivity issue for applications on human-sized scales and show that the use of X-rays with high brilliance, in combination with advanced spatial and spectral filtering, leads to the required reduction of XFI-background. This intrinsic background is predominantly caused by multiple Compton scattering events that lower the energy of the incident photons down to the spectral range of the gold-fluorescence lines. The larger the object, the larger is this intrinsic background effect.

In contrast to brilliant X-ray radiation from large-scale synchrotron facilities, the emergence of compact, laser-based X-ray sources16,17,18,19 supports the possibility for transferring our XFI-method into clinical applications with sufficiently short scanning times.

This work is structured as follows: first, we report on a concrete basic research study on functionalising GNPs for the use in murine spinal cord injury models, demonstrating high levels of sensitivity and specificity as well as sub-mm spatial resolution. The second part addresses the issue of the background problem in case of larger objects, here a 30cm-diameter tissue-equivalent phantom. We first report on numerical simulations of the Compton-background in full 4π and then discuss our spatial filtering scheme supported by different experimental validation studies as well as an analytical model for explaining the background distributions. We have chosen experiments with mono-chromatic and polarised synchrotron X-ray beams as well as with unpolarised beams from a polychromatic X-ray tube, in order to study the comparison of our model with both types of sources. We also discuss the bandwidth limit of our scheme as this determines the applicability of possible X-ray sources.

Results

Localisation of L1-functionalised gold-nanoclusters in murine spinal cords

As a pilot study towards XFI-based PK studies, we first present results of experiments using gold L-shell excitation XFI in murine models with spinal cord injury, and their subsequent treatment with GNPs functionalised with a short peptide derived from the neuronal cell adhesion molecule L1 and thiolated poly(ethylene glycol) (PEG)20,21 see Fig. 1.

We assessed the diffusive behaviour of L1-GNPs using a clinically relevant in vivo model of spinal cord compression22,23,24,25. To this end, thoracic spinal cord injury was performed on adult female mice using well-established paradigms. L1-GNPs were applied 500 µm proximal to the lesion site via an ultra-thin capillary to stimulate neural regeneration. PEGylated GNP probes were used as controls. Following serial assessments as long as over a 48-hour time interval (i.e., 0, 2, 48 hours), injured mice were transcardially perfused, and the spinal cords subjected to XFI using highly-brilliant synchrotron radiation. Mock-injured spinal cords in the absence and presence of L1-GNPs were used for comparison. The aim here is to explore the sensitivity limit of XFI with respect to detecting an unprecedented minimum amount of locally confined tissue-bound biomarkers of high specificity, in addition to achieving sub-mm spatial resolution.

We detected local GNP-masses down to 72 picogram in the scanning pencil beam volume with a diameter of only 0.2 mm (Fig. 2A).

The statistical significance Z (in units of one standard deviation) of this record minimum detection limit in GNP-weight (i.e., 0.0017 wt% or weight-percentage) was Z = 4.3. The main aim of this experiment was to explore the XFI sensitivity limit in the localisation of GNPs, but we also benchmarked the XFI-detectable local GNP masses against inductively coupled plasma mass spectrometry (ICP-MS). Uncertainties in the XFI measurements have been thoroughly studied, and the results from ICP-MS and XFI are in close agreement, noting that no spinal cord was completely scanned, leaving the XFI-signal below ICP-MS values (Fig. 2B). The findings imply that for all post-injection times the entire GNP-mass remains concentrated in the region around the lesion positions, indicating a stable binding of the L1-functionalised GNPs to stressed neurons. On the basis of the XFI-scan obtained at those positions, we deduce an uptake of 0.6% to 1.0% of the total injected GNP-amounts. The transverse scanning (in one plane) along the spinal cords (Fig. 2A) demonstrated strong localisation of the L1-functionalised GNPs at the injection positions (Fig. 2C), an information not available from ICP-MS measurements.

Since the isotropic XFI-signal was measured by a detector with an extremely small fraction of the entire (4π) solid angle, the applied dose was found to be very high. Setting the physical dose limit to 11 mGy (corresponding to 106 incident photons) for 4π-detection and a statistical significance limit of Z = 3, we find a minimum detectable GNP-mass of 2.3( ± 0.7) ng, corresponding to 0.055 wt%. These computed GNP-mass and concentration values are effectively more than one to two orders of magnitude lower than those previously published, taking into account the much smaller scanning beam diameter and the use of significantly lower dose levels than used for other probes, especially in XFI-Computed-Tomography (XFI-CT) schemes (ref.26 and references therein). The critical factor needed to attain high XFI-sensitivity for the low dose administered was the usage of highly brilliant X-ray beams, whose mono-chromaticity allows for quasi background-free measurements.

Solution of “background problem” for large objects

While the above L-shell XFI-experiment demonstrated a quasi background-free setup, its relatively low photon energy makes it impractical for in vivo imaging of objects larger than small animals. On the other hand, K-shell XFI in human-sized objects is expected to suffer from a large intrinsic background27,28,29 (Fig. 3a).

We have set up analytical and numerical studies of the signal and background behaviour. In order to minimise intrinsic background contributions to the measured signal without concomitant signal losses, a scheme utilizing advanced spatial and spectral filtering was developed, derived from the anisotropy of the background. In this work we treat the anisotropy in case of human-sized objects, both for monochromatic polarised and polychromatic unpolarised X-ray photons, both in numerical and experimental studies, and provide an explanation from an analytical model.

In order to address size scales relevant for future XFI-applications on human patients, we simulated a (soft-tissue) sphere with a diameter as large as 30 cm. In its centre, a small sphere with radius of only 0.5 mm has been placed containing gold at the same concentration of 0.23 wt% as that reported in XFI-experiments using tumour-bearing mice26, i.e. from a small-animal model. However, this reported concentration was detected (with a polychromatic benchtop X-ray source) in a cubic voxel of length 2.5 mm, while here we aim to detect the same concentration in just a 1-mm-diameter sphere - a volume, and hence, GNP-mass, a factor of 30 times smaller, i.e. in our case only 1.2 μg. Note that the scheme in ref.26 could not detect this GNP-amount in a 30-cm-object. In our simulation, the large-size phantom was scanned with a pencil beam of 1 mm diameter, defining the spatial resolution of 1 mm, with an average physical dose, i.e. absorbed energy within the scanning beam volume, set to be only 10 mGy.

Our ability to determine both the photon detection scheme with maximum background reduction and optimum incident photon energy is based upon an analysis of the energy-dependent spatial distribution of the multiple Compton scattering background. Since we propose to quantify the signal quality as the combined significance of both the Kα1 and Kα2 lines of the GNPs, we apply spectral filtering around these two lines (within a range of ± 3σdet around each line, with a detector energy resolution of σdet). The manifold of all possible combinations of multiple Compton scatter angles with final energies falling into the range around these two fluorescence lines results in a strongly anisotropic background (Fig. 4a).

Due to this anisotropic background in large objects, a detector covering the full solid angle - similar to the 4π-detection extrapolation of our spinal cord measurements - does not automatically imply an optimised setup (see the corresponding spectrum in Fig. 3a), despite its maximum signal counts.

The two basic constraints, which our detection scheme fulfils, are to (i) allow the GNP-loaded subvolume to be anywhere along the scanning beam volume and (ii) exclude higher-order Compton scattered photons from the scanning pencil beam volume. The first constraint, aimed at maintaining a minimum dose level and time by requiring only a single exposure per scanning direction, rules out any collimators for which GNP position must be known a priori, as assumed e.g. in ref.30 or our own previous work31. The second constraint is realised by using a set of molybdenum leaves, radially arranged around the beam, such that detected photons can only arise from within the scanning beam volume, effectively excluding higher-order Compton photons. The simulated X-ray beam is linearly polarised and chosen to be monochromatic, as would be expected from synchrotron or laser-driven sources – two principle sources that allow a sufficiently fast XFI-scanning time.

The solution to the “background problem” is to consider it as an optimisation problem. To that end, the entire cylindrical detector surface is divided into a set of pixels. For any given incident photon energy, our algorithm determines that subset of pixels whose sum spectrum exhibits the maximum statistical signal significance Z. The single spectrum of each pixel alone does not show a significant signal, hence the spectra of many pixels are added to a sum spectrum. Our algorithm discards those pixels with the largest yields from the adding to a sum spectrum until this sum spectrum shows a statistically significant signal. Once this signal is found, the algorithm then removes further pixels as long as the resulting significance of the remaining sum spectrum reaches a maximum. We have found that this algorithm proves to be robust for arbitrary locations of the gold-distributions inside the object. The sum spectrum of this optimal subset allows the detection of the desired small gold concentration of 0.23 wt%, i.e. 1.2 μg, with a minimum statistical significance limit of Z = 3. We have tested our algorithm with many different incident photon energies and have found that 85 keV delivers the maximum significance Z over all other incident energies. This finding of optimum incident photon energy close to the K-edge energy of gold can be understood in terms of our optimisation solution: the smaller the difference between incident photon energy and the K-edge, the more dominant is single Compton scattering, while higher order Compton scattering becomes more important at higher incident energies. The background of single Compton scattering exhibits the highest degree of anisotropy, which is the basis for the solution presented here. Thus, at higher incident energies, higher Compton order scattering leads to a less and less anisotropic background, precluding the presented spatial filtering.

Figure 4b shows the result of our solution for a polarised X-ray source. If one would use an unpolarised source, the “wave-like” pattern would be transformed into Φ-independent vertical columns. However, we have simulated both cases and have seen that Zpol = 13.62( ± 0.22) and Zunpol = 13.66 ± (0.33).

In order to decrease radiation dose and exposure time, our scheme does not require a full CT because particle localisation can simply be inferred from the intersections of two, e.g. orthogonal, scanning pencil beams (if both indicate a signal). Furthermore, (projection) absorption images along these two directions can be obtained without further exposure.

Validation of background photon distribution

In order to experimentally validate the above solution, which is particularly based on the anisotropic distribution of the scattered photons, we have measured the flux of these background photons emitted from a 30-cm-diameter cylindrical phantom. In addition, for studying the effect of finite bandwidths, we utilised an industrial X-ray tube source with beam collimators and filters, delivering a pencil beam with 3 mm diameter, average photon energy of 90 keV, and 24%

Full-Width-at-Half-Maximum (FWHM) bandwidth. Figure 5 shows measured and simulated photon counts for various detection angles, as well as the comparison with estimates from a simplified mathematical model described below, exhibiting clear overall agreement. In order to validate our claim also with a monochromatic and polarised source, we have performed the same angular scan at a DESY-synchrotron-beamline with 82.8 keV photons. Figure 6 shows the comparison between the measured counts of photons in the signal region with the simulated ones, showing again a very good agreement.

This simplified model is able to explain the angular distribution of the anisotropic Compton-background and is based upon the assumption that most of the photons that are detected by any pixel have taken the shortest path from the entry point to a scatter position z along the incident beam direction and from there directly to the detector pixel. The model thus adds up the yields from all scattering positions along the beam direction. For each scatter position z we have used the (weak) angular dependence a(z) of Compton scattering, but neglect any energy-variation due to scattering. Furthermore, for each position z we take the fraction f(z) of the pixel’s solid angle and the projection p(z) of its area with respect to that position into account, as well as the total transmission T(z) over such shortest paths. For the polychromatic source the mean photon energy was used. We then simply sum up all contributions y(z) over all z-positions to the total yield Y of a given pixel and plot the result versus detector angle. Note that all mentioned functions vary only with the scatter position z: Y = $$\sum _{{z}}y(z)$$, with y(z) = const ∙ a(z)∙f(z)∙p(z)∙T(z), where the constant takes into account all dependencies of the yield which do not depend on z, like the total scattering cross section, the number of incident photons, and the detector efficiency. If the distance from the scatter position z to the detector is called r, then f(z) = $$\frac{A}{4\pi {r}^{2}}$$, with the pixel area A, and T(z) = $${e}^{-\mu (z-{z}_{0}+r)}$$, with µ being the (incident energy dependent) linear attenuation coefficient and z0 the entry position along the beam direction. Note that one could use also the energy dependence for the attenuation coefficient, but its variation is relatively small, which is also the case for the angular dependence and pixel area projection. As it turns out, only T(z) and f(z) vary strongly with z. Since the agreement with both experiments (polychromatic unpolarised X-ray tube source vs monochromatic polarised synchrotron radiation) and corresponding simulations is convincing (s. Figs 5 and 6), it seems as if the underlying principle of this simplified model reflects indeed the basic reason for the found angular distribution of the anisotropic Compton-background, namely the interplay between total path attenuation and relative solid angle which both lead to strong background yields for large detection angles, but “suppress” the yield for forward-angles.

In order to also demonstrate a concrete XFI-measurement with the large 30cm-diamater phantom, we have drilled a vertical hole into the centre of it for placing a high-Z material solution in it. Since we only had a single detector (so to speak only one pixel) available with a correspondingly small effective solid angle, the concentration of the solution must be relatively large to keep measurement times low. Therefore, instead of gold solutions, we have used a Gadolinium-solution with a concentration of 78 mg/ml, which was placed within a 3 mm Eppendorf tube. Fig. 7 shows a direct comparison of the measured and simulated spectrum around the Gd-signal region. The agreement is quite convincing, when keeping in mind that both data sets are not scaled to each other. The (constant) difference between both by about 14% can be mainly attributed to the uncertainty in the measured incoming photon flux (determined by using a photo diode).

Although fluorescence is a non-resonant excitation process, our spatial filtering scheme shows an energy dependence, because the optimum “map” (s. e.g. Fig. 4b) varies slightly with energy, hence one can expect a limit for the bandwidth of the incident X-ray beam. Further simulations revealed a critical X-ray bandwidth of about 15% FWHM, above which the significance Z starts decreasing (by more than 10%). In addition, we have shown that when using the filtered spectrum of the conventional X-ray source, which was used for the data in Fig. 5, the significance Z drops only to 50% of the value for the (simulated) monochromatic case. Hence, our method does not require strictly monochromatic X-ray sources, but depends on sources that deliver synchrotron-like pencil beams.

Translation into clinical application

While pilot studies at large-scale synchrotron facilities are helpful in developing XFI-technology towards scanning of human patients, their sheer size and costs preclude clinical applications. One pathway for translating our XFI-method into clinics is to use compact, laser-based, brilliant X-ray sources16,17,18,19. Here, electrons with relativistic energies oscillate in the field of a counter-propagating laser-pulse. Due to the relativistic energies, the X-ray emission is confined to small forward angles, hence allowing effective collimation for scanning pencil beams32. This collimation, together with the periodic oscillation of the electrons in the laser field, keeps the resulting bandwidths in the above-mentioned limit.

The time needed per scanning direction is fully determined by two factors: (i) the number of photons per second that the used X-ray source can generate within a pencil beam solid angle and (ii) the number of photons per second that the used detector can handle. Synchrotrons can easily produce more than the required 109 photons/sec/mrad2 per scanning direction. Our used Amptek detector can handle an input count rate of about 50 kHz. For measurements where the X-ray beam flux was originally too large, we have used attenuators in the beamline. However, note that the larger the object the smaller the solid angle of each detector and the less restriction from the detector count rate. Our solution to the background problem requires a large area pixelated detector which could be simply realized by an arrangement of many independent detectors of the kind as used in our experiment.

Discussion

In the present work, unprecedented gains in target tissue penetration and detection sensitivity, as well as the ability to precisely and rapidly interrogate disease-bearing tissues utilizing low-dose, molecularly-targeted GNPs, are distinct advantages offered by our novel XFI scheme for human-sized objects. Other XFI-schemes, which are either preferring measurements in certain small angle ranges and/or applying collimators with restricted fields of view on only parts of the entire beam volume, cannot present a low-dose solution to the intrinsic “background problem”, while our spatial filtering opens the path for the background suppression factor demanded for bringing small-animal results from tumour-diagnostics onto size-scales of future human applications. Our optimisation approach is well-justified by experiments as well as by simulations and an analytical model.

Furthermore, for a future utilisation as next-generation tool for monitoring in vivo pharmacokinetics, whereby the distribution of medical drugs to which GNPs are bound can be serially imaged, we have also studied the scaling of XFI with spatial resolution. Here, in contrast to the above-mentioned early small-tumour detection, the spatial resolution can be lowered, e.g. to a 1-cm-diameter sphere. In this case, the scaling of XFI-sensitivity, for the same physical dose and statistical signal significance, predicts that the minimum detectable GNP-mass inside a 1-cm-target-sphere is just 12 µg, while above it is 1.2 µg inside the 1-mm-target-sphere (both embedded in a 30-cm-diameter object), thus lowering the minimum detectable GNP-concentration by a factor of 100.

Outlook

More than 50% of all cancer patients receive radiotherapy (RT) during their treatment regimen33. Despite advances in external beam RT that optimise dose delivery by e.g. beam shaping and real-time imaging, image-guided attenuation of therapy34 for treating early stage cancers and tumour recurrence35, a significant number of patients experience relapse, metastases, and/or significant toxicities to normal tissue36. Such unfavourable outcomes underscore a critical need for new probe-device combinations that can overcome these limitations, e.g. by enhancing RT dose to tumour while sparing normal tissues37,38. The use of targeted high-atomic number radiosensitising materials, such as the GNPs, has served as a promising solution for further increasing RT efficacy39. Particles, initially adapted as cancer-specific imaging probes, localise to and accumulate within tissue targets of interest - and they can be further exploited as imaging agents for image-guided X-ray RT of the target site as they boost local dose deposition to target tumour volumes40. Hence, GNP-based XFI would allow for combining diagnostics and therapy with one and the same device.

As a further step on the path of GNP-technology research, newer generation (i.e., sub 10-nm diameter) GNPs41 will be functionalised with tumour-targeting moieties and contrast labels to create molecularly-targeted cancer imaging probes, as in prior human clinical trials using fluorescent core-shell silica nanoparticles, referred to as Cornell dots, or simply C dots42. These “target-or-clear” sub-10 nm inorganic particle probes exhibit hallmarks of ideal diagnostic probes. Recent studies have shown that GNPs, ranging from 2 to 15 nm in diameter, penetrate and localise within cancer cells, multicellular spheroids, and in vivo tumours in a size-dependent manner43. Further, careful tuning of surface ligand and PEG chain densities to maintain sub-10 nm sizes has led to favourable in vivo biological profiles and radiation dosimetry44, paving the way for product translation in both surgical45 and other oncological settings.

XFI can also be applied to other high-atomic number atoms, e.g. another future application of our XFI-method could be in vivo measuring of Gadolinium(Gd)-retention in human brains and bones from using Gd as a contrast agent in MRI-applications. First estimates, assuming a homogeneous distribution, reveal a sensitivity of about 1 µg per gram (brain/bone) tissue. The main difference between XFI of Gd versus GNP is the lower atomic number and K-shell excitation energy. A similar application could be pharmacokinetic studies for Platinum-based chemotherapeutics (e.g. Cisplatin) and also here we reach the same sensitivity as in the Gd-retention case.

Summing up, for early diagnostic evaluations, including the possibility of higher resolution pharmacokinetic assessments, our spatial filtering scheme presents a low-dose solution to the “background problem” with high spatial resolution for large objects. This solution is validated by experiments and explained by a simplified analytical model. This could trigger further research activities in the fields of biomedical research and molecular imaging towards precision and personalized medicine.

Methods

Experimental Design

L1 peptides

A peptide derived from the third fibronectin type III domain of murine L1 with a lysine linker and a cysteine for coupling at the N-terminus was purchased from Schafer-N (Copenhagen, Denmark) and had the following sequence: H-CKKKKKPELEDITIFNSSTVLVRWRPVD-OH (L1-N-Lys). Poly(ethylene glycol) methyl ether with an average Mw ~ 2000 g mol−1 was purchased from Fluka. All other chemicals and solvents (analytical grade) were ordered from Sigma-Aldrich (Taufkirchen, Germany). Ultrapure water (Millipore, Darmstadt, Germany) was used for all procedures.

GNPs

The ligand a-methoxypoly(ethylene glycol)-w-(11-mercaptoundecanoate) (PEGMUA, M ~ 2000 g/mol) was synthesized. GNPs were synthesized by a seeded growth method; seed particles were synthesized by an optimized Turkevich protocol. GNP40s had a diameter of 37.7( ± 3.5) nm and a concentration of 0.3 nM. GNP30s had a diameter of 31.2( ± 2.0) nm and a concentration of 0.5 nM. GNP40s had a diameter of 37.7( ± 3.5) nm and a concentration of 0.3 nM. The as-synthesized GNPs were stabilized by citrate, which can be easily exchanged by thiols.

Functionalisation of GNPs

Peptide solutions were freshly prepared by solubilizing the peptide in water or phosphate buffered saline solution pH 7.4 (PBS). The solutions were centrifuged (13,000 g, 10 min) and the supernatants filtrated with 0.22 µm PTFE syringe filters (Carl Roth, Germany). The peptide concentrations were determined by UV/vis spectroscopy using the absorbances at 280, 320 and 350 nm. PEGMUA solutions were 1 mM in water. PEGMUA und L1-N-Lys were mixed in a molar ratio 3:1 and GNPs were added under stirring (500 rpm). After thorough shaking of the container, the mixtures were stirred (400 rpm) for 16 h at room temperature. In the case of GNP40s, 50,000 ligands were added per GNP, in the case of GNP30s, 100,000 ligands were added per GNP. After functionalisation the GNPs were concentrated and purified by repeated centrifugation (1,000–5,000 g, 10–15 min) and replacement of the supernatants with water. The final samples had 12 nM (~3.8 g/l) in PBS in the case of GNP40s, while GNP30s had 13 nM (~2.4 g/l) in artificial cerebrospinal fluid. A detailed description of the synthesis and characterisation of these functionalised GNPs can be found in ref.20.

Mice

Female C57BL/6 J mice were obtained from the breeding facility of the University Hospital Hamburg-Eppendorf. Mice were kept at standard laboratory conditions with food and water supply ad libitum and with an artificial 12 h light/dark cycle. All experiments were conducted in accordance with the German and European Community laws on protection of experimental animals, and all procedures used were approved by the responsible authorities of the State of Hamburg (Behörde für Wissenschaft und Gesundheit, Amt für Gesundheit und Verbraucherschutz, Lebensmittelsicherheit und Veterinärmedizin; animal permit numbers ORG 679 Morph and 98/09).

Spinal cord compression injury and tissue preparation for XFI

Spinal cord compression injury was performed as described in ref.25 using three-month-old female C57BL/6 J mice. Following intraperitoneal anesthesia with ketamin and xylazin (100 mg Ketanest, Parke-Davis/Pfizer, Karlsruhe, Germany, and 5 mg Rompun, Bayer, Leverkusen, Germany, per kg body weight), laminectomy at the T7–T9 spinal cord level was performed using a mouse spinal cord compression device to elicit compression force. The compression duration was controlled by an electromagnetic device: the spinal cord was maximally compressed for 1 second by a time-controlled current flow through the electromagnetic device.

Two different concentrations of L1-functionalised and non-functionalised nanoparticles in a volume of 1–2 µl were then applied via a very thin pulled-out single barrel microfilament (outside diameter <500 µm, inside diameter <300 µm, AM Systems) into the spinal cord, 0.5 mm proximal to the lesion site. This method leads to a minimal lesion injury due to the fine geometry of the microcapillary. Muscles and skin were then closed using 6–10 nylon stitches (Ethicon, Norderstedt, Germany). After surgery, mice were kept on a heated pad (37 °C) for 24–48 hours to prevent hypothermia. Injured mice were then intraperitoneally anesthetized with sodium pentobarbital (Narcoren, Merial, Hallbergmoos, Germany, 5 µl/g body weight) and transcardially perfused with 4% formaldehyde in PBS buffer. The spinal cords were isolated and post-fixed overnight at 4 °C. The tissue was then immersed in a lubricating balsam (Bayer) and subjected to XFI.

Synchrotron-based XFI-experiments

XFI experiments of the spinal cords were performed at the Bio-imaging and Diffraction beamline P11 at DESY’s highly brilliant X-ray source PETRA III. The instrument provides linearly polarized photons tunable from 5.5 to 30 keV. Using KB mirrors, the monochromatic X-ray beam can be focused from (300·300) µm2 down to a size of (4·9) µm2 at the sample position (v × h, FWHM) with full flux from the source in the focal spot (2·1013 ph/s at 12 keV). To reach optimal detector dead time aluminium filters were used for flux reduction up to 0.006%. For restricting the scanning time we have chosen 0.2 mm diameter aperture for our measurements. The used Vortex-EM (Hitachi) detector is mounted perpendicular to the incident photon beam and its energy resolution is about 100 eV (rms) around the fluorescence lines. For the reconstruction of gold masses in spinal cords, a silicon waver with a (20.8 ± 0.8) nm sputtered gold layer was used as a reference target. Measured spectra were normalized by this reference and corrected by the transmission factors of the spinal cord geometry, which was approximated by a cylinder having a length of 10 mm and a radius of 1 mm. Taking inbound and outbound transmission properties into account, the optimum incident photon energy was found to be 15 keV. Gaussian peaks were used to fit background and gold fluorescence peaks. For the Compton tail, an exponential function was used.

ICP-MS measurements of GNP concentrations in spinal cords

For sample preparation, a microwave-assisted digestion (ETHOS.lab, MLS, Leutkirch, Germany) of the spinal cord was performed using 5 ml nitric acid (65% w/v; VWR, Fontenay-sous-Bois, France), 1 ml hydrochloric acid (32% w/v; Merck KGaA, Darmstadt, Germany) and 0.5 ml hydrogen peroxide (30% w/v; VWR, Leuven, Belgium). Digested samples were diluted with ultrapure water from a Millipore system (Direct-Q® 3 UV-R, Millipore, Bedford, MA, USA) to 20 ml for measurements. Gold nanoparticle concentrations were determined by inductively coupled plasma mass spectrometry (ICP-MS) on a 7700x instrument (Agilent Technologies, Santa Clara, CA, USA). Standard solutions were prepared from a 1 g/l gold stock solution (Merck Millipore, Billerica, MA, USA). The method detection limit was determined with 1 ng/l. It should be noted that while ICP-MS probes the total GNP-mass per spinal cord, it does not provide any spatial information. The error bars in Fig. 2 are the statistical variation from three consecutive measurements of the same probe.

Simulation tools

For the extrapolation onto human-sized phantoms we used simulations with the simulation toolkit GEANT446. A “soft tissue” sphere with a diameter of 30 cm consisting of a GEANT4 material called “G4_TISSUE_SOFT_ICRP” (Geant4 User’s Guide for Application Developers Geant4 Collaboration Version: geant4 10.0, 6 December 2013) was considered.

The assumed detector resolution of σdet = 200 eV (rms) was chosen close to the value of a real detector, that is, from the Amptek XR-100T-CdTe detector, whose resolution at 60 keV is 255 eV (rms). Note that the significance Z scales inversely with the square root of the detector resolution (i.e. a resolution of 255 eV instead of 200 eV lowers Z by 13%).

The radial collimator leaves started at a radius R = 30 cm, ended at R = 60 cm, and extended axially along the entire detector. The detector had a radius of 60 cm and a length of 1.60 m. The need for a collimator was met before we found out the optimum incident photon energy to be close to the K-edge. Thus, the vast majority of background photons in the signal region are Compton1(!)-photons, for which the collimator has no effect. Using a collimator is still useful to reduce the detector input count rate from multiply-Compton-scatted photons.

Validation experiments

We used an YXLON X-ray tube, model MG160, operated with 100 kV voltage, 20 mA current, and “N150”-filters (consisting of 4 mm aluminium and 2.5 mm tin). The pencil beam geometry was realised by a collimator with diameter of 3 mm and 30 mm length. The phantom was a cylinder made out of PMMA, with diameter of 30 cm and a height of 6 cm. We used the XR-100T-CdTe detector from Amptek, which was positioned at various angle positions directly on the phantom’s surface. Note that the simulation used the same number of incident photons as in the experiment and that we incorporated the detector geometry and the corresponding acceptance solid angle into the simulation. The synchrotron validation experiments were performed at the DESY P07 beamline, which satisfies high energy x-ray diffraction (XRD) and imaging techniques. It is tunable in the range 30 to 200 keV and optimised for micrometre focusing with Compound Refractive Lenses (CRLs). For the experiments we have chosen 4·108 ph/s at 82.8 keV within a pencil beam of (100·100) µm2 and horizontal polarisation. The Gadolinium solution had a concentration of 78 mg/ml and was placed within a 3 mm Eppendorf tube, embedded in the 30cm-diameter phantom. Also here we have used the Amptek-detector.

In order to correct the CdTe-detector signals for the so-called hole-tailing effect, we have calibrated the detector with a series of different radioactive source covering a wide range of incident photon energies, as well as two dedicated experiments at the DESY-synchrotron, one using a direct (strongly attenuated) beam on the detector, whereby the energies are tuned in a wide range, and another one with fixed beamline energy, but different thin scatter foils of different (high-Z) materials, hence tuning the incident energy by making use of the different energies of the singly-Compton-scattered photons. With these data we have studied the parameters for mathematical functions that “smear” out the simulated raw data (with an ideal detector) into data for the realistic detector. Since today there is no large area CdTe-detector available, it is clear that so far we can only move our single detector through the full 4π solid angle, thus mimicking the situation once such a large area detector version is available. The simplest technical solution would be to place many single detectors next to each other.

Statistical Analysis

As the signals in the experiments and simulations consisted of two fluorescence peaks, we decided to use Significance (Z) as a measurement of signal quality instead of the usual Signal-to-Noise ratio. This significance Z is calculated from the p-value (probability that the measured level above background is not just a fluctuation), using the number of signal photons of both fluorescence peaks and the number of background photons in a region of ± 3σdet around the peaks, all numbers derived from Gaussian fits. Typically, Z is given in units of a standard deviation σ (sigma) of a normal distribution. A significance level of 3σ (i.e. 99.73%) was chosen to be the minimum signal strength.

Data Availability

All raw and processed data generated in this work, including the data for the figures provided in the manuscript, are available from the corresponding author on reasonable request.

References

1. 1.

Park, S., Aalipour, S. A., Vermesh, O., Yu, J. H. & Gambhir, S. S. Towards clinically translatable in vivo nanodiagnostics. Nat. Rev. Mater. 2, 1–20 (2017).

2. 2.

Berning, S., Willig, K. I., Steffens, H., Dibaj, P. & Hell, S. W. Nanoscopy in a living mouse brain. Science 335, 551 (2012).

3. 3.

Gleich, B. & Weizenecker, J. Tomographic imaging using the nonlinear response of magnetic particles. Nature 435, 1214–1217 (2005).

4. 4.

Weissleder, R., Nahrendorf, M. & Pittet, M. J. Imaging macrophages with nanoparticles. Nat. Mater. 13, 125–138 (2014).

5. 5.

Tomasetti, C., Li, L. & Vogelstein, B. Stem cell divisions, somatic mutations, cancer etiology, and cancer prevention. Science 355, 1330–1334 (2017).

6. 6.

Mestel, R. Cancer: Imaging with antibodies. Nature 543, 743–746 (2017).

7. 7.

Santangelo, P. J. et al. Whole-body immunoPET reveals active SIV dynamics in viremic and antiretroviral therapy–treated macaques. Nat. Methods 12, 427–432 (2015).

8. 8.

Keu, K. V. et al. Reporter gene imaging of targeted T cell immunotherapy in recurrent glioma. Sci. Transl. Med. 18, eaag2196 (2017).

9. 9.

Kuang, Y. et al. Development of XFCT imaging strategy for mon- itoring the spatial distribution of platinum-based chemodrugs: Instru- mentation and phantom validation. Medical Physics 40(3), 030701 (2013).

10. 10.

Cheong, S.-K. et al. X-ray fluorescence computed tomography (XFCT) imaging of gold nanoparticle-loaded objects using 110 kVp x-rays. Physics in Medicine & Biology 55(3), 647 (2010).

11. 11.

Jones, B. & Cho, S. H. The feasibility of polychromatic cone-beam x-ray fluorescence computed tomography (XFCT) imaging of gold nanoparticle-loaded objects: a monte carlo study. Physics in Medicine & Biology. 56(12), 3719 (2011).

12. 12.

Jones, B., Manohar, N., Reynoso, F., Karellas, A. & Cho, S. H. Experimental demonstration of benchtop x-ray fluorescence computed tomography (xfct) of gold nanoparticle-loaded ob- jects using lead- and tin-filtered polychromatic cone-beams. Physics in Medicine & Biology 57(23), N457 (2012).

13. 13.

Bazalova, M., Kuang, Y., Pratx, G. & Xing, L. Investigation of x-ray fluorescence computed tomography (XFCT) and k-edge imaging. IEEE Transactions on Medical Imaging. 31(8), 1620–1627 (2012).

14. 14.

Bazalova, M., Ahmad, M., Pratx, G. & Xing, L. L shell x-ray fluorescence computed tomography (xfct) imaging of cisplatin. Physics in Medicine & Biology 59(1), 219 (2014).

15. 15.

Kuang, Y. et al. First demonstration of multiplexed x-ray fluorescence computed tomography (xfct) imaging. IEEE Transactions on Medical Imaging 32(2), 262–267 (2013).

16. 16.

Achterhold, K. et al. Monochromatic computed tomography with a compact laser-driven X-ray source. Sci. Rep. 3, 1313 (2013).

17. 17.

Jacquet, M. High intensity compact compton X-ray sources: challenges and potential of applications. Nucl. Instrum. Methods B 331, 1–5 (2014).

18. 18.

Powers, N. D. et al. Quasimonoenergetic and tunable X-rays from a laser-driven Compton light source. Nat. Photonics 8, 29–32 (2014).

19. 19.

Ta Phuoc, K. et al. All-optical Compton gamma-ray source. Nat. Photonics 6, 308–311 (2012).

20. 20.

Schulz, F. et al. Gold nanoparticles functionalized with a fragment of the neural cell adhesion molecule L1 stimulate L1-mediated functions. Nanoscale 5, 10605–10617 (2013).

21. 21.

Papastefanaki, F. et al. Intraspinal delivery of polyethylene glycol-coated gold nanoparticles promotes functional recovery after spinal cord injury. Mol. Ther. 23, 993–1002 (2015).

22. 22.

Kataria, H., Lutz, D., Chaudhary, H., Schachner, M. & Loers, G. Small molecule agonists of cell adhesion molecule L1 mimic L1 functions in vivo. Mol. Neurobiol. 53, 4461–4483 (2016).

23. 23.

Loers, G., Cui, Y. F., Neumaier, I., Schachner, M. & Skerra, A. A Fab fragment directed against the neural cell adhesion molecule L1 enhances functional recovery after injury of the adult mouse spinal cord. Biochem. J. 460, 437–446 (2014).

24. 24.

Lutz, D. et al. Myelin basic protein cleaves cell adhesion molecule L1 and improves regeneration after injury. Mol. Neurobiol. 53, 3360–3376 (2016).

25. 25.

Saini, V. et al. The polysialic acid mimetics 5-nonyloxytryptamine and vinorelbine facilitate nervous system repair. Sci. Rep. 6, 26927 (2016).

26. 26.

Manohar, N. et al. Quantitative imaging of gold nanoparticle distribution in a tumour-bearing mouse using benchtop x-ray fluorescence computed tomography. Sci. Rep. 6, 22079 (2016).

27. 27.

Vernekohl, D., Ahmad, M., Chinn, G. & Xing, L. Feasibility study of Compton cameras for x-ray fluorescence computed tomography with humans. Physics in Medicine & Biology 61(24), 8521–8540 (2016).

28. 28.

Ahmad, M., Bazalova, M., Xiang, L. & Xing, L. Order of Magnitude Sensitivity Increase in X-rayFluorescence Computed Tomography (XFCT) Imaging With an Optimized Spectro-Spatial Detector Configuration: Theory and Simulation. IEEE Transactions on Medical Imaging 33(5), 1119 (2014).

29. 29.

Ahmad, M., Bazalova-Carter, M., Fahrig, R. & Xing, L. Optimized Detector Angular Configuration Increases the Sensitivity of X-ray Fluorescence Computed Tomography (XFCT). IEEE Transactions on Medical Imaging 34(5), 1140 (2015).

30. 30.

Sjölin, M. & Danielsson, M. Improved signal-to-noise ratio for non-perpendicular detection angles in x-ray fluorescence computed tomography (XFCT). Phys. Med. Biol. 59, 6507–6520 (2014).

31. 31.

Müller, B., Hoeschen, C., Grüner, F., Arkadiev, V. & Johnson, T. Molecular imaging based on x-ray fluorescent high-Z tracers. Phys. Med. Biol. 58, 8063–8076 (2013).

32. 32.

Rykovanov, S. G. et al. Quasi-monoenergetic femtosecond photon sources from Thomson Scattering using laser plasma accelerators and plasma channels. J. of Physics B: Atomic, Molecular and Optical Physics 47, 234013 (2014).

33. 33.

Wang, A. Z. & Tepper, J. E. Nanotechnology in Radiation Oncology. J. Clin. Oncol. 32, 2879–2885 (2014).

34. 34.

Thariat, J., Hannoun-Levi, J.-M., Sun Myint, A., Vuong, T. & Gérard, J.-P. Past, present, and future of radiotherapy for the benefit of patients. Nat. Rev. Clin. Oncol. 10, 52–60 (2013).

35. 35.

Salama, J. K., Kirkpatrick, J. P. & Yin, F.-F. Stereotactic body radiotherapy treatment of extracranial metastases. Nat. Rev. Clin. Oncol. 9, 654–665 (2012).

36. 36.

Nguyen, P. L., D’Amico, A. V., Lee, A. K. & Suh, W. W. Patient selection, cancer control, and complications after salvage local therapy for post-radiation prostate-specific antigen failure: a systematic review of the literature. Cancer 110, 1417–1428 (2007).

37. 37.

Keall, P. J. et al. The management of respiratory motion in radiation oncology report of American Association of Physicists in Medicine (AAPM) Task Group 76. Med. Phys. 33, 3874–3900 (2006).

38. 38.

Moding, E. J., Kastan, M. B. & Kirsch, D. G. Strategies for optimizing the response of cancer and normal tissues to radiation. Nat. Rev. Drug. Discov. 12, 526–542 (2013).

39. 39.

Schuemann, J. et al. Roadmap to clinical use of gold nanoparticles for radiation sensitization. Int. J. Radiation Oncol. Biol. Phys. 94, 189e205 (2016).

40. 40.

Popovtzer, A. et al. Actively targeted gold nanoparticles as novel radiosensitizer agents: an in vivo head and neck cancer model. Nanoscale 8, 2678–2685 (2016).

41. 41.

Sun, Y., Sai, H., Von Stein, F., Riccio, M. & Wiesner, U. Water-based synthesis of ultrasmall PEGylated gold-silica core-shell nanoparticles with long-term stability. Chem. Mater. 26, 5201–5207 (2014).

42. 42.

Phillips, E. et al. Clinical translation of an ultrasmall inorganic optical-PET imaging nanoparticle probe. Sci. Transl. Med. 6, 260ra149 (2014).

43. 43.

Huang, K. et al. Size-dependent localisation and penetration of ultrasmall gold nanoparticles in cancer cells, multicellular spheroids, and tumours in vivo. ACS Nano 6, 4483–4493 (2012).

44. 44.

Benezra, M. et al. Multimodal silica nanoparticles are effective cancer-targeted probes in a model of human melanoma. J. Clin. Invest. 121, 2768–2780 (2011).

45. 45.

Bradbury, M. S. et al. Clinically-translated silica nanoparticles as dual-modality cancer-targeted probes for image-guided surgery and interventions. Integr. Biol. 5, 74–86 (2013).

46. 46.

Allison, J. et al. Recent developments in GEANT4. Nuclear Instruments and Methods in Physics Research A 835, 186–225 (2016).

Acknowledgements

Parts of this research were carried out at beamline P11 at PETRA III, DESY, a member of the Helmholtz Association (HGF). M.B. and U.W. acknowledge funding from the National Institutes of Health under grant 1U54 CA199081-01. F.S. is supported by the DFG via the project SCHU 3019/2-1.O. S. is funded by the PIER Helmholtz Graduate School.

Author information

Authors

Contributions

F.G., M.B., U.W., M.K. and C.H. conceived of the project. F.B., F.G., and C.H. developed the solution to the “background problem”. D.L. and G.L. prepared the murine spinal cord probes. F.G., F.B., O.S., T.S., D.L., S.S., M.W., A.B., A.M. and C.H. performed the synchrotron experiment. O.S. analysed the spinal cord experimental data. T.S., O.S. and T.R. performed the validation experiment. B.R. and M.F. made the ICP-MS measurement. F.S. prepared the functionalised GNPs.

Corresponding author

Correspondence to Florian Grüner.

Ethics declarations

Competing Interests

Through the University of Hamburg, F.G., F.B. and C.H. (as the inventors) have submitted a patent application about the advanced XFI-scheme, application number 10 2017 003 517.2, application status: pending. The other co-authors declare no competing financial interests. All authors declare no competing non-financial interest.

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and Permissions

Grüner, F., Blumendorf, F., Schmutzler, O. et al. Localising functionalised gold-nanoparticles in murine spinal cords by X-ray fluorescence imaging and background-reduction through spatial filtering for human-sized objects. Sci Rep 8, 16561 (2018). https://doi.org/10.1038/s41598-018-34925-3

• Accepted:

• Published:

Keywords

• Gold Nanoparticles (GNPs)
• Spatial Filtering Scheme
• Intrinsic Background
• Spinal Cord Compression Injury
• Compton Scatter

• Design study for a compact laser-driven source for medical x-ray fluorescence imaging

• Theresa Brümmer
• , Alexander Debus
• , Richard Pausch
• , Jens Osterhoff
•  & Florian Grüner

Physical Review Accelerators and Beams (2020)

• Tomographic reconstruction algorithms for structured gas density profiles of the targets for laser wakefield acceleration

• S Lorenz
• , G Grittani
• , L V N Goncalves
• , C M Lazzarini
• , J Limpouch
• , M Nevrkla
• , S Bulanov
•  & G Korn

Measurement Science and Technology (2020)

• Optimized EDXRF system for simultaneous detection of gold and silver nanoparticles in tumor phantom

• M. Santibáñez
• , R. Saavedra
• , J. Vedelago
• , F. Malano
•  & M. Valente