Glacial retreat in recent decades has exposed unstable slopes and allowed deep water to extend beneath some of those slopes. Slope failure at the terminus of Tyndall Glacier on 17 October 2015 sent 180 million tons of rock into Taan Fiord, Alaska. The resulting tsunami reached elevations as high as 193 m, one of the highest tsunami runups ever documented worldwide. Precursory deformation began decades before failure, and the event left a distinct sedimentary record, showing that geologic evidence can help understand past occurrences of similar events, and might provide forewarning. The event was detected within hours through automated seismological techniques, which also estimated the mass and direction of the slide - all of which were later confirmed by remote sensing. Our field observations provide a benchmark for modeling landslide and tsunami hazards. Inverse and forward modeling can provide the framework of a detailed understanding of the geologic and hazards implications of similar events. Our results call attention to an indirect effect of climate change that is increasing the frequency and magnitude of natural hazards near glaciated mountains.
Climate change is driving worldwide glacial retreat and thinning1 that can expose unstable hillslopes. The removal of glacial ice supporting steep slopes combined with the thawing of permafrost in alpine regions2 increases the likelihood of landslides3,4,5,6. Glaciers undercut slopes, priming them for failure by deepening and widening valley bottoms, and by producing steeper valley walls7. Additionally, ice loading produces stress fractures in the underlying bedrock, further preparing slopes for failure8. As climate warms and glaciers shrink and retreat, they can no longer support rock slopes, and fractures expand as stresses are released. This slope conditioning leads to rock falls, deep-seated gravitational slope deformation, and occasionally catastrophic rock avalanches4,9,10.
A further effect of glacial retreat is the creation or extension of bodies of deep water, fresh or marine11,12, where tsunamis can be generated efficiently (Table 1). Along the glacially sculpted coastlines of Alaska, Patagonia, Norway, and Greenland, communities, tourism, and infrastructure are becoming increasingly exposed to such landslides and the tsunamis they may generate. Tsunamis in lakes can create flood risk downstream by flowing into inhabited downstream valleys (e.g.13,14,15).
Tsunamis triggered by landslide impact can have an order of magnitude shorter periods and higher runups than those driven by tectonics that have dominated tsunami hazard research in recent years16. While tectonic tsunamis typically have periods in the tens of minutes and peak runups extending up to around 30 m, the best studied landslide tsunami, which occurred in 1958 in Alaska’s Lituya Bay, had a period of about 76 seconds and peak runup of 524 m17. The geologic traces of the Lituya Bay landslide and tsunami have not been documented, providing no analogue for identification of ancient short-period, large-runup tsunamis in the geologic record, be they caused by landslides, volcanoes, or meteor impacts. The only field data available to constrain these reconstructions are the deposits of the 2000 AD landslide-triggered tsunami in Vaigat Strait, West Greenland18, and surficial descriptions of deposits from the tsunami in Grewingk Lake in 196719. The event we describe here in Taan Fiord, Alaska provides the best example to date of a well-documented subaerial landslide that generated a tsunami, and of its impacts on a fjord, coupled with detailed examination of its deposits (see Supplementary Fig. online). This study provides crucial insight into landslide-triggered tsunami processes and the various traces of such events.
The 2015 Taan Fiord landslide
On 17 October 2015, a massive landslide and tsunami occurred at the head of Taan Fiord, an arm of Icy Bay within Wrangell-St. Elias National Park & Preserve in Alaska (Fig. 1). The slope failure was primed by rapid ice loss from a tidewater glacier in a tectonically active setting. Tyndall Glacier filled Taan Fiord as recently as 196120. Rapid warming over the past half century led to 17 km of terminus retreat and over 400 m of ice thinning between 1961 and 1991. Since 1991, the terminus of Tyndall Glacier has stabilized at a shallow bedrock constriction at the head of the fjord20,21 (Fig. 2). The slope that failed was above the calving front and slid directly into the fjord along the terminus, partially covering the toe of the glacier. Destruction of vegetation and other tsunami traces clearly delineate runup throughout the fjord. Directly across from the landslide, runup reached 193 m, (as compared to 240 m in an initial model estimate22). Runup exceeded 100 m for 1.5 km, overrunning over 1 km2 of area. Further down-fjord, Runup varied dramatically, but generally declined to about 15 m at the mouth of the 17 km long fjord (Fig. 2).
Ongoing tectonic deformation likely contributed to the Taan Fiord landslide. The present-day glacier terminus lies along the east-west oriented Chaix Hills Fault, one of many structures that accommodate rapid (4–5 mm a−1) tectonic uplift of poorly lithified Miocene-Holocene rocks to high elevations in the St. Elias orogen21,23. Uplift of weak and faulted rock likely intensified glacial erosion, leading to rapid valley excavation. Subsequent glacial retreat debuttressed the oversteepened fjord wall, initiating progressive failure of the slope that eventually culminated in catastrophic collapse and a tsunami.
Signs of prior hillslope deformation at the location of the 2015 landslide might have provided forewarning. Slumping along the fjord wall at the site was first identified in 199621 and grabens are visible in Landsat images as early as 1995. A comparison of Digital Elevation Models (DEMs) and optical satellite imagery show downslope motion throughout much of the ensuing two decades until the catastrophic failure in October 2015 (Fig. 3). While the 2015 Taan Fiord landslide and tsunami did not result in fatalities, actively deforming slopes in more populated places (e.g. Tidal Inlet, Glacier Bay National Park, Alaska24) may be harbingers of more deadly landslide-generated tsunamis in the future. Monitoring gradual downslope motion in mountain ranges around the world, while a technical challenge, would provide a step forward in our ability to mitigate risk.
The final trigger for the landslide is unclear. Seismic waves from a MW 4.1 earthquake about 500 km away arrived about 2 minutes before the failure, producing ground motion that would not be uncommon multiple times a year in this area25, but might have contributed to the final failure. Similarly, 2015 rains at the nearest gage 110 km away in Yakutat were about 10% more than usual in Sept. and Oct (as-usual the rainiest months of the year). Such deviations above average are common in the years preceding the landslide, but elevated water tables may have contributed at least to the seasonal timing.
Landslide detection and extent
We first identified the 2015 landslide by seismic inversion, using the method of Ekstrom and Stark26,27. The seismic waves of the Taan Fiord landslide, equivalent to a M 4.9 earthquake, were observed globally. We used an automated landslide detector to identify the seismic signal within hours of the event, which included an abundance of 20 to 100 second period energy, as is typical of large landslides25. Long-period waveforms from the Alaska Regional Network were used to determine the forces associated with the landslide and to refine the estimated location to within 5 km. Seismic inversion suggested an eastward-moving (bearing 96°) landslide that generated peak forces of about 2 × 1011 N and lasting 90 seconds. The landslide source location inferred from seismology was near the calving front of Tyndall Glacier (Fig. 2). Based on earlier mapping of fjord geometry18, the seismogenic motion of the landslide was assigned a length of 1.5 km. These findings, combined with the seismologically determined force history, further suggested a slide mass of 1–1.5 × 1011 kg. Thus, the Taan Fiord landslide was one of the largest non-volcanic landslides in decades26,28.
These initial estimates were revised within the next year by satellite and aerial imagery, lidar, and ground surveys. The landslide above the terminus of Tyndall Glacier unleashed 7.6 × 107 m3, or 1.8 × 1011 kg of debris. The estimated volume and mass is based on the difference between 2012 and 2016 DEMs, and on an estimate of the slide material remaining in the slide scar. Extending the failure plane beneath onland deposits shows that about 33% of the evacuated volume is still onshore; the rest entered the fjord. Presuming that initial motion was downslope, the landslide moved in a direction similar to that inferred by seismic inversion. The majority of the slide followed the fjord bottom, curving right in an approximately 90° arc blanketing the fjord bottom to its limit 6 km from the source28 (Fig. 2). Additional slide material travelled directly eastward through the fjord (Fig. 2) and up onto the far shore, depositing hummocks of semi-coherent slide material that blanket the fjord bottom and crest ~15 m above sea level29. This material likely traversed across the bottom of the 90 m-deep fjord and then traveled upwards 105 m to reach its final resting place.
If we assume that the hummocks represent the leading edge of the landslide, the slide velocity must have been at least 45 m s−1 (162 km h−1) for the Taan landslide, similar to values reported for other rock avalanches of comparable dimensions (1903 Frank slide, Alberta, Canada: 3 × 107 m3, 49 m s−1; 1912 Mageik, Alaska: 5.4 × 107 m3, 24 m s−1; 1925 Gros Ventre slide, US-Wyoming: 3.8 × 107 m3, 59 m s−1)30. This estimate is based on the simple conversion of kinetic to potential energy v = (2gh)0.5 often used in landslide studies to estimate flow velocity from runup height (h)31, assuming no potential energy transfers from the body of the slide to the leading edge. These assumptions can overstate maximum velocities in some cases31, but also fail to account for friction or the transfer of momentum to water. Alternatively, the hummocks may represent a later phase of the landslide that travelled over earlier deposits that had partly filled in the fjord. In this case, the hummocks would have traversed water as shallow as 50 m, and the minimum flow velocity for the slide would be closer to 36 m s−1 (130 km h−1).
Tsunami generation, propagation, and runup
When landslides enter water, the direct hazard they pose (e.g.32,33) can be extended by the resultant tsunami (e.g.17,18,34). In Taan Fiord the landslide directly affected about 2 km2 of land onshore, while over 20 km2 were inundated by the tsunami. We derive the initial tsunami geometry, constrained by landslide volume and aspect ratio, velocity, and duration35. Using a coupled set of solid and fluid mechanics models35, we estimate that the measured landslide dimensions and material properties generated a leading wave near the head of the fjord with crest elevation of 100 m and period of 90 seconds. In the 100 m water depth near the source area, the front of this wave would have started to break at this crest height, approaching the sloping fan on the far side of the fjord as a plunging or surging breaker. To reach its peak elevation of 193 m (Figs 2, 4), the tsunami required enough initial kinetic and potential energy to not only climb the slope, but also overcome energy lost to turbulent dissipation and sediment interaction.
The tsunami traveled south away from the landslide source area, down the fjord. Shallow water wave theory (aka long water wave theory36) computes a propagation speed of (gh)0.5, or about 30 m s−1 in Taan Fjord’s 100 m deep water. The tsunami proceeded to strip alder forest to elevations exceeding 50 m along the upper 7 km of the fjord, before encountering a range of hills (Fig. 2). These hills caused complex wave interference, expressed as runup elevations that rise and fall by tens of meters across distances of a few hundred meters (Fig. 4). Variability in the flow is further evidenced by uneven stripping of soil, and by the diverse orientations of still-rooted but flattened trees. Farther down the fjord, runup was diminished, reaching between 10 and 30 m elevation. Even with these relatively low runup elevations, the tsunami energy during overland flow was strong enough to leave only soil and debris where young forest with a 10 m canopy previously stood. The leading crest of the tsunami exited the fjord within 12 minutes, based on numerical modeling of the tsunami (see Methods). At distances greater than 5 km from the mouth of Taan Fiord, tsunami runup was below the high tide shoreline and no longer directly measureable during our first field survey six months after the event.
Geologic traces of the tsunami
The tsunami left thick distinctive deposits that were unlike those documented from other modern tsunamis16 as it overran and resurfaced several alluvial fans along Taan Fiord (see Supplementary Fig.). On the hardest-hit fan (Hoof Hill Fan) the change in surface elevation between DEMs from before and after the event showed the deposit exceeded 5 m thick in places. Even at the most distal fan studied, where the tsunami runup had diminished to 16 m, the deposit was still 40 cm thick. These deposits included many fragments of supple wood, sometimes overlaid pre-tsunami soil, and occasionally included uphill flow-direction indicators. Deposits characterized from numerous recent tectonic tsunamis were typically sandy, less than 10 cm thick, and often normally graded14. Some of the Taan Fiord tsunami deposits were similarly normally graded as well, however in most ways they were very different. They included abundant coarse sediment ranging up to boulders, and are composed of three distinct units that we could find no analog for in the literature describing tsunami recent historic tsunami deposits.
The three units were most distinct where the tsunami was largest, at Hoof Hill Fan. The lower unit (A) is composed of sand to boulders, while the upper unit (B) is typically well-sorted and composed of cobbles or boulders. A third unit (C), composed of normally graded sand, was found where it infiltrated unit B.
Similar three-part deposits also partially blanketed fans farther down-fjord, although in many cases unit B was thin or absent, and in a few places the deposit was capped by complex layered sediment that we left uncategorized. Unit A might resemble debris flows from upland sources but can be distinguished by evidence of scour and of uphill flow found at the base. Unit B is similar to, but more tabular and widespread than, sieve deposits found on alluvial fans37. DEM differencing shows that these deposits are widespread and commonly meters thick at Hoof Hill Fan (Fig. 5), and thus likely to be preserved for millennia. Deposits in more sediment-poor settings are thin and patchy, but include transported boulders up to 5 m in diameter.
The difference between the deposits in Taan Fiord and those that have been recently described in other tsunamis might be due to differences in sediment source, depositional setting, or wave shape, among other things. The difference in deposit composition may simply reflect a difference in sediment source: In both Taan Fiord and tsunami deposits elsewhere, the bulk composition of the deposit is similar to the source sediment, whether that source is sandy beaches or bouldery alluvial fans. Also, a fan is importantly different from a coastal plain because the retreating wave may have the capacity to rework significant sediment as it runs down the sloping surface. In contrast, coastal plains drain more slowly, and typically sediment is only mobilized in localized constrictions during withdrawal16. Finally, while tectonic tsunamis have a long period, usually over 10 minutes, the period of the Taan Fiord tsunami was likely similar to the 90 seconds it took the slide to do most of its acceleration and deceleration. This difference in period likely had large impacts on temporal and spatial variability in the tsunami flow as it moved onland, and thus on the erosion and deposition of sediment.
The tsunami deposits in Taan Fiord may be particularly useful in identifying or interpreting deposits of similar events that produce short-period waves, and send those waves over sloping surfaces with diverse sediment available. For example, deposits interpreted to have been generated by landslide tsunamis have been documented in Hawaii38 and the Canary Islands39, pre-Quaternary deposits in the rock-record have been interpreted as records of large landslide or impact-generated tsunamis (summary in 14), and possible impact-generated tsunami traces have been described on Mars40,41. The deposits in Taan Fiord provide the first well-constrained example that might be used to interpret these and other ancient deposits, in order to better understand the frequency and magnitude of landslide and bolide impact tsunamis. If viewed independently, and out of geomorphic context, neither of the sedimentary units left by the Taan tsunami are necessarily indicative of a landslide-triggered, short-period tsunami. However, taken together and contextualized with the other evidence, the sedimentary deposits may prove sufficiently distinct to aid in the identification of paleo tsunamis. We provide more detailed descriptions of the tsunami sedimentology in the Supplementary Figure.
Implications for hazards assessment
The landslide and tsunami predicated by glacial retreat at Taan Fiord represents a hazard occasioned by climate change. More such landslides are likely to occur as mountain glaciers continue to shrink and alpine permafrost thaws. These landslides can more often be expected to produce tsunamis as water bodies grow and extend landward, closer to steep mountain slopes. Other notable landslides have occurred in recently deglaciated regions (e.g.3,4,9) and some have produced tsunamis (e.g.17,19,34,42,43, Table 1). Their locations, though mostly remote, are attracting tourism and development. For example, incomplete failure and ongoing slow slip have been documented on a slope at Tidal Inlet, a fjord in Glacier Bay National Park, 6 km from a channel visited by dozens of cruise ships during summer months24. On 28 June, 2016, an approximately 1.5 × 1011 kg landslide collapsed onto Lamplugh Glacier, also in Glacier Bay National Park, but luckily did not reach tidewater and so did not trigger a tsunami44,45. Then on 17 June, 2017, a landslide in Rink Fiord triggered a tsunami that killed 4 people in Nuugaatsiaq, Greenland, 30 km away, highlighting the need for further study of these phenomena.
Comparison of pre- and post-event data at Taan Fiord constrain the dimensions of the landslide and tsunami, and in turn may aid in identifying other such events in the recent geologic past. In order to mitigate the risk associated with landslide-triggered tsunamis, we suggest the following: 1) revisit geologic records of paleotsunamis to better understand frequency and causal mechanisms of past occurrences; 2) assess areas of potential failure given known glacial histories and evidence of precursory motion; and in areas of particular concern, 3) map areas of likely impact using glacier, landslide, and tsunami inundation models in order to reduce impacts should an event occur; and finally 4) monitor for landslides using seismic and remote-sensing techniques.
For our landslide volume estimate, documentation of precursory motion, and mapping of deposit thickness (Fig. 5) we used a variety of Digital Elevation Model (DEM) and imagery sources. The earliest DEMs are taken from airborne interferometric synthetic aperture radar data (InSAR), while more recent DEMs come from satellite photogrammetry, as well as airborne lidar and structure-from-motion (SfM). The InSAR-based DEM’s are taken from 2002 and 2012; these are freely available 5-m resolution models, and can be downloaded at http://maps.dggs.alaska.gov/elevationdata/#-16000000:9338001:4. We construct satellite DEMs, including the 2014 DEM referenced in Fig. 5, from high-resolution along-track stereo optical satellite imagery using SETSM46 on the University of North Carolina Chapel Hills’ Killdevil HPC system. The resulting DEMs have a resolution of 2 m. The optical DEMs are co-registered to the 2012 InSAR DEMs by masking out all water and snow and ice from the InSAR DEMs, leaving only bedrock, converting the InSAR bedrock into a pointcloud then applying an iterative closest point matching routine to minimize the RMS difference between the optical DEM and the InSAR DEM. DEMs used in this study are available from both the Polar Geospatial Center at the University of Minnessota, and similar DEMs of the area, registered to satellite altimetry using different methods than this study are available from the ArcticDEM project (Arcticdem.org).
During 2016 fieldwork we collected lidar and imagery for SfM over Taan fjord and parts of Icy bay. The lidar was collected using methodology from47, and SfM topography and ortho-imagery was produced using methodology in48.
DEM differencing shows that 5.8 × 107m3 of landslide material is missing - providing a minimum volume on the landslide. By extrapolating the failure plain beneath slide material still onshore, we expand this estimate to 7.6 × 107m3. To estimate the mass represented by this volume, we used a density of 2350 kg/m3. Most of the landslide material is a weakly lithified sandstone. Sandstones have density values between 2150 and 2650 kg/m3 49. The value of 2350 kg/m3 is based on rocks from the Susitna and Cook Inlet basins, Alaska, which have a similar composition, age, and burial history (e.g.50,51).
To understand precursory motion, we compared successive DEMs, and also reviewed imagery provided through Google Timelapse44, which presents Landsat imagery that is clear enough for identifying landslide scarps and grabens back to 1995.
We used a variety of instruments to perform the ground-based tsunami runup survey. The instruments that were used to survey the tsunami markers included a laser rangefinder, a total station, and two differential Real Time Kinematic (RTK) GPS systems. A combination of these instruments was commonly used for a single measurement point, as the terrain was difficult and flow markers were at times inaccessible. There were four different general approaches for surveying data points in this survey. The first approach was used for markers located on steep mountain slopes, where run-up was clear, but not easily accessible, and required shooting from a distance. For such points, the RTK-GPS system was used in combination with the rangefinder to obtain a spatial location. A second approach was employed in situations where the ample forestry or tree tops obstructed the RTK-GPS signal. In this scenario, a combination of the total station and the RTK-GPS system was used to obtain the necessary coordinate points with high accuracy. Thirdly, for flow markers of large elevation (e.g. more than 10 meters) and/or large inundation distance (e.g. many 100 s of meters) that were also entirely accessible due to relatively easy terrain and lack of dense canopy, the RTK-GPS system was used on its own. Finally, for flow markers of relatively low elevation and inundation distance, the rangefinder on its own was used in locations where it was not practical to setup the RTK base and rover system. In the paragraphs below, we briefly describe each of the measurement devices, and their expected precision.
The RTK-GPS system was used to in order to achieve highest possible accuracy. Survey monuments were created throughout Taan Fiord, and their coordinates were determined via static GPS measurements. Many monuments were established to accommodate the radius of radio coverage of the RTK-GPS system. The expected errors are +/−1 cm for the horizontal, +/−3 cm for the vertical measurement using RTK-GPS. In addition to instrument error, some human error must be taken into account. The human error is estimated to be +/−5 cm in holding the pole upright and on stable ground. Thus the RTK-GPS systems are expected to have measurement errors bounded by 10 cm.
When using the total station, the instrument location was determined by acquiring its relative location to four well-distributed points with known coordinates. Following the setup of the total station, a surveyor used a reflector to collect the tsunami markers. The errors for a typical distance of ~200–300 m are +/−1.5 mm for the distance, +/−0.001° for the inclination, and +/−0.001° for the bearing. The human error was again determined to be +/−5 cm in holding the pole upright and on stable ground.
When used in conjunction with a RTK system or the total station, the rangefinder location was determined from the RTK rover, and the distance/vertical angle/bearing measurements from the rangefinder provided the coordinates of the tsunami marker. The errors for a typical distance of ~50–10 0 m are +/−30 cm for the distance, +/−0.25° for the inclination, +/−1° for the bearing. The human error in holding the rangefinder vertically and steady was determined to be +/−10 cm.
As discussed above, the expected errors of each measurement are strongly dependent on the equipment used as well as the local terrain, but are likely less than 10 cm for measurements not using the rangefinder, and less than 30 cm for measurements using the rangefinder. In addition, the tsunami marker elevations need to be presented as relative to the tidal level at the time of the tsunami. Of course, there are no direct measurements of the sea level in Icy Bay during the tsunami. Based on sea level data measurement during the field campaigns, we find that the tides within Icy Bay match those at the NOAA tide station in Yakutat, to within 14 cm at high and low tide, with a mean RMS error of 3 cm. Therefore, the error associated with referencing the runup measurements to the sea level at the time of the tsunami is on the same order or smaller than the error in the runup measurements themselves.
Tsunami source model
To approximate the landslide motion and initial generation of the tsunami, we use the 3D Simplified Arbitrary Lagrangian Eulerian model (iSALE) in the area within 3 km of the slide. The slide geometry and motion are constrained by observations of the failure area, and the force time-history of the slide. We use the tsunami generated by iSALE to specify the initial condition in the weakly dispersive, nonlinear Cornell University Long and Intermediate Wave Model (COULWAVE). COULWAVE simulates the tsunami evolution through Taan Fiord and Icy Bay, including relevant dissipation from wave breaking and bottom friction (results not presented in this paper). Ref.30 contains technical details on both of these models, as well as details of the coupling.
To characterize the Taan tsunami deposits, we documented outcrops and trenches across several alluvial fan-deltas. Outcrops were opportunistic, while most trenches were chosen to be in areas of relatively little variation in the surface of the deposit. Trenching and documenting was extended down to the upper part of pre-tsunami sediment wherever possible. Each was described, photographed, and sampled, with particular attention being paid to grain-size variability and contacts within the tsunami deposit. We provide descriptions of the outcrops in the Supplemental Figure.
Tsunami deposits were easily distinguished from underlying pre-tsunami alluvial fan-delta deposits. We documented tsunami deposits within 9 months of the tsunami, and fragmented wood that had been living at the time of the event remained supple and green where it was trapped in the deposit. These provided clear markers for tsunami deposits. In some cases, pre-tsunami soil, roots, and rooted vegetation highlighted the base of tsunami deposits, though often the soil was scoured away, and the decades-old soil was typically faint.
Marine Geophysical Surveys
During Summer 2016, we acquired multibeam bathymetry data from the R/V Alaskan Gyre and from a remotely operated surface vehicle the Jokull for all of Taan Fiord. Also, multichannel 2D seismic data were acquired from the Alaskan Gyre. These data are discussed explicitly in 28 and 29 and are only used here to provide a general description of the submarine part of the landslide.
Grain size distribution data available upon request to firstname.lastname@example.org.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Roe, G. H., Baker, M. B. & Herla, F. Centennial glacier retreat as categorical evidence of regional climate change. Nature Geoscience 10, 95–99 (2016).
Gruber, S. & Haeberli, W. Permafrost in steep bedrock slopes and its temperature‐related destabilization following climate change. Journal of Geophysical Research Earth Surface 112, https://doi.org/10.1029/2006JF000547 (2007).
Coe, J. A., Bessette-Kirton, E. K. & Geertsema, M. Increasing rock-avalanche size and mobility in Glacier Bay National Park and Preserve Alaska detected from 1984 to 2016 Landsat imagery. Landslides. https://doi.org/10.1007/s10346-017-0879-7 (2017).
Deline, P., Hewitt, K., Reznichenko, N. & Shugar, D. Rock avalanches onto glaciers in Landslide Hazards Risks and Disasters 263–319, https://doi.org/10.1016/b978-0-12-396452-6.00009-4 (Elsevier, 2015).
McColl, S. T. Paraglacial rock-slope stability. Geomorphology 153–154, 1–16 (2012).
Kos, A. et al. Contemporary glacier retreat triggers a rapid landslide response Great Aletsch Glacier, Switzerland. Geophysical Research Letters 43(12), 466–12,474 (2016).
Harbor, J. M. Numerical modeling of the development of U-shaped valleys by glacial erosion. Geological Society of America Bulletin 104, 1364–1375 (1992).
Grämiger, L. M., Moore, J. R., Gischig, V. S., Ivy-Ochs, S. & Loew, S. Beyond debuttressing: Mechanics of paraglacial rock slope damage during repeat glacial cycles. Journal of Geophysical Research: Earth Surface 122, 1004–1036 (2017).
Geertsema, M. Initial observations of the 11 June 2012 rock/ice avalanche, Lituya mountain, Alaska. In The First Meeting of International Consortium of Landslides Cold Region Landslides Network, Harbin, China 49–54 (2012).
Shugar, D. H. & Clague, J. J. The sedimentology and geomorphology of rock avalanche deposits on glaciers. Sedimentology 58, 1762–1783 (2011).
Haritashya, U. K. et al. Evolution and Controls of Large Glacial Lakes in the Nepal Himalaya. Remote Sensing 10(5), 798 (2018).
Harrison, S. et al. Climate change and the global pattern of moraine-dammed glacial lake outburst floods. The Cryosphere 12, 1195–1209 (2018).
Clague, J. J. Cryospheric hazards. Geology Today 29, 73–79 (2013).
Evans, S. G. & Clague, J. J. Recent climatic change and catastrophic geomorphic processes in mountain environments. Geomorphology 10, 107–128 (1994).
Cook, S. J., Kougkoulos, I., Edwards, L. A., Dortch, J. & Hoffmann, D. Glacier change and glacial lake outburst flood risk in the Bolivian Andes. The Cryosphere 10, 2399–2413, https://doi.org/10.5194/tc-10-2399-2016 (2016).
Bourgeois, J. Geologic effects and records of tsunamis. The Sea 15, 53–91 (2009).
Fritz, H. M., Mohammed, F. & Yoo, J. Lituya Bay landslide impact generated mega-tsunami 50th anniversary. Pure and Applied Geophysics 166(1–2), 153–175, https://doi.org/10.1007/s00024-008-0435-4 (2009).
Buchwał, A., Szczuciński, W., Strzelecki, M. C. & Long, A. J. New insights into the 21 November 2000 tsunami in West Greenland from analyses of the tree-ring structure of Salix glauca. Polish Polar Research 36 (2015).
Wiles, G. C. & Calkin, P. E. Reconstruction of a debris-slide-initiated flood in the southern Kenai Mountains Alaska. Geomorphology 5, 535–546 (1992).
Koppes, M. & Hallet, B. Erosion rates during rapid deglaciation in Icy Bay Alaska. Journal of Geophysical Research 111 (2006).
Meigs, A., Krugh, W. C., Davis, K. & Bank, G. Ultra-rapid landscape response and sediment yield following glacier retreat Icy Bay, southern Alaska. Geomorphology 78, 207–221 (2006).
George, D. L., Iverson, R. M. & Cannon, C. M. New methodology for computing tsunami generation by subaerial landslides: Application to the 2015 Tyndall Glacier landslide Alaska. Geophysical Research Letters 44, 7276–7284 (2017).
Enkelmann, E. et al. Cooperation among tectonic and surface processes in the St. Elias Range Earth’s highest coastal mountains. Geophysical Research Letters 42, 5838–5846 (2015).
Wieczorek, G. F., Geist, E. L., Motyka, R. J. & Jakob, M. Hazard assessment of the Tidal Inlet landslide and potential subsequent tsunami Glacier Bay National Park, Alaska. Landslides 4, 205–215 (2007).
USGS ANSS Comprehensive Earthquake Catalog, https://earthquake.usgs.gov/earthquakes/search/ accessed 1 Sept 2017.
Ekstrom, G. & Stark, C. P. Simple scaling of catastrophic landslide dynamics. Science 339, 1416–1419 (2013).
Gualtieri, L. & Ekström, G. Broad-band seismic analysis and modeling of the 2015 Taan Fjord, Alaska landslide using Instaseis. Geophysics Journal International 213, 1912–1923 (2018).
Haeussler, P. J. et al. Submarine deposition of a subaerial landslide, Taan Fiord, Alaska. Journal of Geophysical Research-Earth Surface. 19 p., 13 figs (submitted).
Dufresne, A. et al. Sedimentology and geomorphology of a large tsunamigenic landslide, Taan Fiord, Alaska. Journal of Sedimentology (2017)
Jibson, R. W., Harp, E. L., Schulz, W. & Keefer, D. K. Large rock avalanches triggered by the M 7.9 Denali Fault Alaska, earthquake of 3 November 2002. Engineering Geology 83, 144–160 (2006).
Iverson, R. M., George, D. L. & Logan, M. Debris flow runup on vertical barriers and adverse slopes. Journal of Geophysical Research: Earth Surface 121, 2333–2357 (2016).
Petley, D. Global patterns of loss of life from landslides. Geology 40, 927–930 (2012).
Kirschbaum, D. B., Adler, R., Hong, Y., Hill, S. & Lerner-Lam, A. A global landslide catalog for hazard applications: method results, and limitations. Natural Hazards 52, 561–575 (2009).
Miller, D. J. Giant waves in lituya bay, Alaska. (US Government Printing Office Washington, DC, 1960).
Weiss, R., Fritz, H. M. & Wünnemann, K. Hybrid modeling of the mega-tsunami runup in Lituya Bay after half a century. Geophysical Research Letters 36 (2009).
Lagrange, J. L. Sur la manière de rectifier deux endroits des principes de Newton relatifs à la propagation du son et au mouvement des ondes. Nouv. Mém. Acad. Berlin 5, 591–609 (1786).
Hooke, R. L. Processes on Arid-Region Alluvial Fans. The Journal of Geology 75, 438–460 (1967).
McMurtry, G. M., Watts, P., Fryer, G. J., Smith, J. R. & Imamura, F. Giant landslides mega-tsunamis, and paleo-sea level in the Hawaiian Islands. Marine Geology 203, 219–233 (2004).
Pérez-Torrado, F. J. et al. Tsunami deposits related to flank collapse in oceanic volcanoes: The Agaete Valley evidence Gran Canaria, Canary Islands. Marine Geology 227, 135–149 (2006).
Rodriguez, J. A. P. et al. Tsunami waves extensively resurfaced the shorelines of an early Martian ocean. Scientific Reports 6 (2016).
Costard, F. et al. Modeling tsunami propagation and the emplacement of thumbprint terrain in an early Mars ocean. Journal of Geophysical Research: Planets 122, 633–649 (2017).
Roberts, N. J. et al. Impacts of the 2007 landslide-generated tsunami in Chehalis Lake, Canada in Landslide Science and Practice 6: Risk Assessment, Management and Mitigation (eds Margottini, C. Canuti, P. & Sassa, K.) 133–140, https://doi.org/10.1007/978-3-642-31319-6_19 (Springer Berlin Heidelberg, 2013).
Roberts, N. J., McKillop, R., Hermanns, R. L., Clague, J. J. & Oppikofer, T. Preliminary global catalogue of displacement waves from subaerial landslides in Landslide Science for a Safer Geoenvironment 3: Targeted landslides (eds Sassa, K. Canuti, P. & Yueping, Y.) 687–692, https://doi.org/10.1007/978-3-319-04996-0_104 (Springer-Verlag, 2014).
Coe, J. A., Bessette-Kirton, E. K. & Geertsema, M. Increasing rock-avalanche size and mobility in Glacier Bay National Park and Preserve, Alaska detected from 1984 to 2016 Landsat imagery. Landslides 15(3), 393–407 (2017).
Bessette‐Kirton, E. K., Coe, J. A. & Zhou, W. Using Stereo Satellite Imagery to Account for Ablation, Entrainment, and Compaction in Volume Calculations for Rock Avalanches on Glaciers: Application to the 2016 Lamplugh Rock Avalanche in Glacier Bay National Park, Alaska. Journal of Geophysical Research – Earth Surface 123(4), 622–641 (2018).
Noh, M.-J. & Howat, I. M. Automated sterio-photogrammetric DEM generation at high latitudes: Surface Extraction with TIN-based Search-space Minimization (SETSM) validation and demonstration over glaciated regions. GIScience & Remote Sensing 52(2), 198–217 (2015).
Johnson, A. J., Larsen, C. F., Murphy, N., Arendt, A. A. & Zirnheld, S. L. Mass balance in the Glacier Bay area of Alaska, USA, and British Columbia, Canada, 1995–2011 using airborne laser altimetry. Journal of Glaciology 59, 632–648 (2013).
Nolan, M., Larsen, C. & Sturm, M. Mapping snow depth from manned aircraft on landscape scales at centimeter resolution using structure-from-motion photogrammetry. The Cryosphere 9, 1445–1463 (2015).
Sharma, P. V. Environmental and engineering geophysics. (Cambridge university press, 1997).
Hackett, S. W. Regional gravity survey of Beluga Basin and adjacent area Cook Inlet region, southcentral Alaska. (Alaska Division of Geological & Geophysical Surveys, 1976). doi: 10.14509/5.
Saltus, R. W., Haeussler, P. J., Bracken, R. E., Doucette, J. P. & Jachens, R. C. Anchorage urban region aeromagnetics (AURA) project—preliminary geophysical results. US Geological Survey Open-File Report 01–0085 (2001).
Gorelick, N. et al. Google Earth Engine: Planetary-scale geospatial analysis for everyone. Remote Sensing of Environment, https://doi.org/10.1016/j.rse.2017.06.031 (2017).
NGDC/WDS, N. G. D. C. W. D. S. Global Historical Tsunami Database. National Geophysical Data Center, NOAA, https://doi.org/10.7289/V5PN93H7 (2017).
The text benefitted from USGS internal review by Brian Atwater and Stephanie Ross. The work was funded by National Science Foundation grants EAR-1639643, EAR-1638898, EAR-1639010, EAR-1638931, EAR-1638979, EAR-1638434, CMMI-1650357, the U.S. Geological Survey, Virginia Tech, the Canadian National Science and Engineering Research Council Discovery Grants program, and the Oceans Alaska Science and Learning Center, a National Park Service partner. We thank the University of North Carolina at Chapel Hill Research Computing group for providing computational resources that have contributed to these research results. Geospatial support for this work provided by the Polar Geospatial Center under NSF PLR awards 1043681 and 1559691. This is UTIG Contribution #3281. Several DEMs were used in this paper, and all are publicly available or available by request.
Electronic supplementary material
About this article
Analysis of generation and arrival time of landslide tsunami to Palu City due to the 2018 Sulawesi earthquake
Numerical Modeling of the June 17, 2017 Landslide and Tsunami Events in Karrat Fjord, West Greenland
Pure and Applied Geophysics (2019)