The intensification of agricultural production to meet the growing demand for agricultural commodities is increasing the use of chemicals. The ability of soils to transport dissolved chemicals depends on both the soil’s texture and structure. Assessment of the transport of dissolved chemicals (solutes) through soils is performed using breakthrough curves (BTCs) where the application of a solute at one site and its appearance over time at another are recorded. Obtaining BTCs from laboratory studies is extremely expensive and time- and labour-consuming. Visible–near-infrared (vis–NIR) spectroscopy is well recognized for its measurement speed and for its low data acquisition cost and can be used for quantitative estimation of basic soil properties such as clay and organic matter. In this study, for the first time ever, vis–NIR spectroscopy was used to predict dissolved chemical breakthrough curves obtained from tritium transport experiments on a large variety of intact soil columns. Averaged across the field, BTCs were estimated with a high degree of accuracy. So, with vis-NIR spectroscopy, the mass transport of dissolved chemicals can be measured, paving the way for next-generation measurements and monitoring of dissolved chemical transport by spectroscopy.
The use of agrochemicals has since the green revolution been an integral part of agricultural intensification to meet the increasing demand for agricultural commodities1,2. The extensive use of agrochemicals in agriculture causes pollution of water resources, which poses serious threats to aquatic ecosystems, human health, and the environment2,3. The occurrence of agrochemicals and/or their degradation products above the permissible limits in drinking water wells has forced numerous wells to be shut down and the implementation of strict regulations on the use of agrochemicals in the EU countries3,4. Soil is the most important transport pathway for agrochemicals to groundwater. Although soil is acknowledged as fundamental for agricultural production, it is equally important for its ability to filter nutrients and pollutants, and for storing and recycling organic material (or carbon)5,6. This ability is dependent on the soil’s properties and their interactions and is influenced by how soils are used and managed7,8.
Understanding the leaching of dissolved chemicals (solutes) to groundwater and being able to measure and model it is important for health and the environment. The rate and the amount of dissolved chemicals transported through the soil is largely governed by the arrangement of particles and pore networks within the soil, also referred to as the soil structure/architecture9. Soil structure is a very dynamic property since it is influenced by basic soil properties such as texture, organic matter, carbonates and metal oxides, the climate, and the land use and management practices10. Depending on the soil structure, at near water-saturated conditions, water and dissolved chemicals can, either be transported evenly through the soil, or rapidly through specific pathways in the soil with various degrees of mass exchange between the soil matrix and the transporting pathways. Various solute transport models have been developed to account for different transport processes and facilitate the prediction of the transport of dissolved chemicals through soils11,12. Despite our current understanding of the transport processes of water and dissolved chemicals through soils and the availability of various solute transport models, accurate predictions of solute transport is not yet possible. One of the major challenges is to obtain an accurate range of parameters for use in solute transport models to account for the spatial differences in transport properties. Breakthrough curves (BTCs) obtained from column experiments in the laboratory are usually used for deriving estimates of the parameters for solute transport models. However, performing solute transport experiments with a high spatial resolution to account for the spatial diversity in the transport properties is unfeasible.
In soil science, pedotransfer functions are used to estimate soil properties or model parameters that are difficult to measure, expensive and/or time- and labour-consuming, using readily available soil information13,14. There have been only few attempts to develop pedotransfer functions to estimate the parameters for solute transport models using basic soil properties13,15. However, obtaining many of the basic soil properties to cover the spatial variability in the landscape is a challenge. In recent years, soil spectroscopy (visible, near- and/or mid-infrared) has proven to be a useful analytical tool for rapid and precise estimation of numerous soil physical, chemical and biological properties such as clay content and mineralogy, soil organic carbon, N, extractable P, K, Fe, soil pH and CEC16,17,18. McBratney et al.19 suggested the use of soil spectroscopy to bridge the gap between pedotransfer functions and data availability for the prediction of soil functional properties. However, they also reported large uncertainties in the prediction of the desired soil property due to the buildup propagation of uncertainties in the calculation. Recent studies20,21 have shown that soil spectroscopy can directly be used to estimate soil hydraulic properties with prediction uncertainties comparable to those obtained using pedotransfer functions. In this study, for the first time ever, we set visible–near-infrared (vis–NIR) spectroscopy the challenge of providing fast estimates of mass transport of dissolved chemicals through intact soils (Fig. 1).
Dissolved Chemical Mass Transport Through Soils
Flow and transport processes are often studied in the laboratory on soil columns using BTCs. BTCs are obtained from solute transport experiments where the concentrations recovery of the solute applied to one end of the column are measured at the other end at different time intervals. BTCs with early breakthrough, sharp peaks and significant tailing are related to preferential flow22 which is the rapid transport of water and solutes through a few preferential pathways while bypassing most of the soil matrix23. Preferential flow or non-uniform flow is often associated with heterogeneities in the soil caused by e.g., macropores (inter-aggregate pores, biopores, cracks and fissures)12. Uniform flow is related to homogeneous soils and is characterized by bell-shaped BTCs with late breakthrough of solutes.
Figure 2 shows the field-average BTCs expressed as the relative concentration (Fig. 2a) or the cumulative concentration (Fig. 2b) of the tracer (tritium) recovered during the column experiments for six fields in Denmark with varying texture and organic carbon (OC) contents (Supplementary Fig. 1). Significant differences in the shapes of the BTCs ranging from strong preferential flow in Voldbjerg clayey soils to uniform/homogeneous flow in Jyndevad sandy soils were observed. Large variations in the shapes of BTCs within the fields were also present (Supplementary Fig. 3). The degree of preferential transport generally decreased with decreasing clay content. However, for the Estrup field with a gradient in OC (0.018–0.084 kg kg−1) and a clay content similar to Faardrup, the BTCs were characterized by a lower degree of preferential transport than the Faardrup soils.
Soil texture (especially the type and amount of clay) and OC are important for soil aggregation and structure10. Soils with high clay content can contain cracks and fissures due to wetting-drying and freeze-thaw cycles which can result in heterogeneity of soil structure and thus preferential transport24. Besides clay content25,26, organic carbon content27, water saturation28 and bulk density29 also influence the degree of preferential transport through soils. However, many of these soil properties such as organic matter and bulk density27,30, bulk density and saturation ratio30 are correlated. Based on X-ray-computed tomography analysis of soils, Katuwal et al.31 reported that the strength of preferential, and especially the initiation of macropore flow, is influenced by the conductivity or the porosity of the soil matrix which also determines the degree of saturation30. Naveed et al.32 measured soil-moisture retention curves for soils with a clay gradient between 11 and 46% and observed that for soils with 11% clay the pore networks were dominated by pores >3 µm, which were also characterized by a broad range of pore sizes. With increasing clay content the distribution of pores >3 µm narrowed and the overall pore networks were increasingly dominated by pores <3 µm, resulting in diminishing rates of air conductivity with increasing clay content. The presence of macropores in soils with a high clay content (i.e., less conductive soil matrix) thus directs water and solutes towards the macropores, resulting in preferential flow. Conversely, a lack of macropores in such soils can cause ponding at high irrigation rates and such soil columns are usually excluded from further analysis28,33. Organic carbon, on the other hand, promotes soil aggregation and increases homogeneity in the soil structure, thus reducing preferential transport through soils27, which was also represented by the BTCs of the Estrup soil.
Variation in Soil Spectra
The spectral data obtained from a soil sample is the result of the interaction of the incident radiation with the molecules/molecular bonds present in the soil. Different molecules present in soil absorb energy at specific wavelengths in the visible and the near-infrared range. The absorption of energy in the visible range is primarily due to electronic transitions of atoms whereas in the near-infrared range it is due to overtones and combinations of fundamental vibrations in the mid-infrared range associated with molecular bonds such as (CH, OH, NH, SO4, and CO3 groups)17,34. The spectral data, thus contain information that reflect the soil’s composition and its properties, which with the use of chemometrics can be used for the simultaneous estimation of several properties such as texture, clay mineralogy, organic and inorganic carbon, CEC, pH, moisture content, mineral oxides and others with a high degree of accuracy16,17.
Figure 3 shows the average field spectra for the studied soils along with the common bonds/functional groups present in soil and their corresponding wavelengths in the visible–near-infrared region35. Variations in the overall absorbance and the intensity of absorbance at specific wavelengths or bands were observed both among the fields and within the fields. The coarse-textured Jyndevad soils had higher absorbance related to the scattering effect associated with coarse fractions in soil and/or a higher degree of coating with organic matter18. The fine-textured Voldbjerg soil had lower absorbance associated with the finer texture and the lighter colour. In general, the soils from different fields showed variations in the absorbance at wavelengths associated with iron oxides (400–500 nm), clay minerals (OH bond: 1400 nm, 1900 nm, Al-OH bond: 2200 nm and organic matter (CH bond: 2300–2400 nm) present in the soil36,37. Variations in the spectra within the fields were related to the variations in the soil properties (texture and OC) within the fields (Supplementary Fig. 5). Large within-field variations in the spectra were obtained for Voldbjerg soils with its large variation in clay content and Estrup soils with its variation in organic carbon content.
Prediction Of Arrival Times And Field-Average Btcs
An arrival time represents the time it takes for a definite fraction of solute to be recovered from the end of a soil column and is obtained from the cumulative BTCs (Fig. 2b). Arrival times from 5–50% were obtained from the BTCs and estimated using vis–NIR spectroscopy data by performing partial least squares (PLS) regression with10-fold cross-validation. No attempts were made to fit solute transport models to the BTCs and estimate the fitted parameters since the dominant flow process in the soils varied widely from strong preferential to clear uniform flow, suggesting that a single model could not be used for fitting the BTCs11.
Figure 4(a–h) shows the prediction results for various arrival times of the tracer (5, 10, 15, 20, 25, 30 and 50% and denoted by T5–50 respectively) using vis–NIR spectra. A comparison of the estimated field-average BTCs to the measured field-average BTCs for the six fields is presented in Fig. 5. The estimation accuracies were higher for the early arrival times as compared to the later arrival times (Table 1). Scatter along the 1:1 line was observed for soils from all the fields and increased with the later arrival times. Strong agreements between the measured field-average BTCs and estimated BTCs using vis–NIR spectroscopy were obtained for the different fields (Fig. 5a–f). There was a greater variation in the predicted arrival times compared to the measured values for the Voldbjerg soils (Figs 4 and 5a). Despite the large variation in clay content, the Voldbjerg soils had less variation in BTCs, basically due to the dominance of preferential flow through macropores for the experimental conditions. For soils from the other fields, especially Silstrup, Faardrup, and Tylstrup, vis–NIR spectroscopy did not result in the large variances in the arrival times as with the measured values (Figs 4 and 5). Such underestimation of variances in the estimated soil water retention using different pedotransfer functions has also been reported by Pringle et al.38. The Silstrup, Faardrup and Tylstrup fields are characterized by small gradients in clay and OC content (Silstrup: 0.147–0.197 kg kg−1 clay and 0.017–0.022 kg kg−1 OC, Faardrup: 0.101–0.192 kg kg−1 clay and 0.010–0.015 kg kg−1 OC and Tylstrup: 0.034–0.045 kg kg−1 clay and 0.017–0.020 kg kg−1 OC). Previous studies by Soares et al.39 and Norgaard et al.40 found that the degree of preferential transport in the Faardrup and Silstrup fields correlated best with bulk density. Bulk density in the soils from the two fields was to some extent correlated to OC. However, soil bulk density is also influenced by other factors such as agricultural management practices and biological activities, which cannot be detected by vis–NIR spectroscopy.
For the same 181 soils, Karup et al.33 showed that the range of arrival times (5–50%) of the applied solute can be predicted using basic soil properties such as the volumetric content of fines (clay and silt), which is a ratio of the gravimetric mass fraction of fines times the soil bulk density to the particle density of fines. However, this requires that quantitative information of the fines content and bulk density of the soils is available for such estimations, which is resource-demanding. The RMSE values for the arrival times obtained in this study using vis–NIR spectroscopy are similar to those obtained by Karup et al.33. However, it should be noted that the results in this study are based on a 10-fold cross-validation, whereas the RMSE values in Karup et al. are based on regression analyses on the entire data set without any validation. The cross-validation results (also the calibration-validation results in the supplementary section, Supplementary Figs 7 and 8, and Supplementary Table 2) of this study show that vis–NIR could be used for rapid and acceptable predictions of the arrival times. To extend vis–NIR calibration models to other fields, does however require additional measurements from the target fields before the models can be utilized successfully. Good prediction performance of the arrival times also means that vis–NIR spectroscopy can function as a rapid alternative for estimating mass solute BTCs for various direct and indirect solute transport applications such as optimization of parameters in solute transport modelling, and risk assessment of pollutants. Even though there is an issue with the underestimation of the within-field variances with vis–NIR spectroscopy, the efficiency of this technology in terms of cost and speed of measurement may outweigh a few expensive and precise measurements of soil properties which usually have large spatial variability41. Nonetheless, approaches for reducing the estimation error resulting from differences in soil structure that cannot be captured by vis–NIR spectroscopy should be further investigated. Integration of vis–NIR spectroscopy with other readily available information such as soil structure information based on soil surveys or quick field tests may improve the prediction accuracies and should be explored. Moreover, as the user community within the area of soil science is increasing, specific standard procedures for measurements and the specification of equipment used should be followed in order to merge data from different sources42. A few-seconds’ spectroscopic reading combined with PLS analyses can likely provide rapid, inexpensive predictions of not only static soil properties but also dynamic soil properties like chemical mass transport as a platform for next-generation soil measurements and monitoring.
Field sites and soils
The soils used in the study have already been described in earlier studies30,31,33,40,43,44. In this study, 181 soil samples collected from the top 20-cm depth from six different fields in Denmark (Supplementary Fig. 1) were studied. The soils from the different fields varied in texture and organic carbon (OC) content to different degrees. The Voldbjerg field (56° 18′ 71″ N, 8° 54′ 87″ E, 1.4 ha) is characterized by a gradient in clay content (0.196–0.426 kg kg−1) where the texture of the topsoil varied from loam to silty clay while OC varied only between 0.017–0.020 kg kg−1 (ref.33). The topsoil in the Silstrup field (56° 55′ 56″ N, 8° 38′ 44″ E, 1.7 ha) is a sandy clay loam/sandy loam with 0.147–0.197 kg kg−1 clay and 0.017–0.022 kg kg−1 OC40. The topsoil in the Faardrup field (55° 19′ 1″ N, 11° 20′ 34″ E, 2.3 ha) is a sandy loam soil with 0.101–0.192 kg kg−1 clay and 0.010–0.015 kg kg−1 OC31. The Estrup field (55° 29′ 10″ N, 9° 04′ 9″ E, 1.3 ha) is a heterogeneous field with a gradient in OC, where the topsoil is a sandy loam soil with 0.055–0.140 kg kg−1 clay and 0.018-0.084 kg kg−1 OC30. Both Jyndevad (54° 53′ 37″ N, 9° 07′ 12″ E, 2.4 ha) and Tylstrup (57° 10′ 47″ N, 9° 57′ 24″ E, 1.1 ha) have coarser textures and were more homogeneous than the other fields. The topsoil in Jyndevad is a sandy soil with a clay content of 0.037–0.052 kg kg−1 and OC of 0.014–0.025 kg kg−1 (ref.44). The topsoil in Tylstrup is a loamy sand with a clay content of 0.034–0.045 kg kg−1 and OC of 0.017–0.020 kg kg−1 (ref.33). The latest agricultural management practices in the fields before sampling included ploughing to 20–25 cm depth and cropping with winter wheat/winter rye and/or spring barley. The soil samples from these fields were collected between 2010 and 2014. At the time of soil sampling the fields had not been ploughed for at least a year.
For the solute transport experiments, intact soil columns (20 cm in diameter and 18–20 cm in height) were collected from the topsoil. Aluminum or steel cylindrical rings (20 × 20 cm) were pushed into the soil using the hydraulic press of a tractor until the soil surface was close to the cylinder rim. The surrounding soil was removed manually to extract the soil columns, which were then trimmed at the bottom, sealed with plastic caps and stored at 2 °C until the experiments were performed.
Bulk soil samples from the same depth (0–20 cm) and sampling points were collected and mixed thoroughly. The soils were air-dried, ground and sieved through a 2-mm sieve. A combination of wet sieving and hydrometer methods following Gee and Or45 were used for determining soil texture. The OC content was measured on ball-milled samples with a FLASH 2000 NC organic elemental analyser (Thermo Fisher Scientific Inc., Waltham, MA, USA).
Dissolved chemical transport experiments
Supplementary Fig. 2 shows the setup for the solute transport experiment. The soil columns were slowly saturated from the bottom with an artificial soil water solution (0.652 mM NaCl, 0.025 mM KCl, 1.842 mM CaCl2 and 0.255 mM MgCl2; pH = 6.38; EC = 0.6 mS cm−1) and drained to a matric potential of -10 cm at the bottom. The drained columns were placed on a 1-mm stainless steel wire mesh to allow free drainage from the bottom of the columns. Irrigation was applied to the top at an intensity of 10 mm h−1 with an artificial rainwater solution (0.012 mM CaCl2, 0.015 mM MgCl2 and 0.121 mM NaCl; EC = 0.025 mS cm−1; pH = 6.5) using a rotating irrigation head. The rotating irrigation head consisted of 44 hypodermic needles placed randomly to ensure homogeneity during irrigation on the soil surface. A funnel connected to the wire mesh assembly at the discharge end of the soil column delivered the effluent to bottles placed on a rotating table below the soil columns. The irrigation was applied for 6–18 h after the breakthrough of irrigation water from the bottom of the columns. When the discharge from the soil column was steady, a conservative tracer consisting of tritium solution (3H2O) applied as a pulse for 10 minutes replaced the irrigation water. The activity of tritium in the effluent collected at different time intervals was analyzed using a liquid scintillation analyzer (Packard 2250 CA, Downers Grove, IL, USA). The concentrations/fractions of tracer transported to the outflow at various time intervals were determined from the effluent. The breakthrough curves (BTCs) were expressed as the relative concentration of the tracer (Fig. 2a) and the cumulative mass of the tracer (Fig. 2b). To obtain the field-average BTCs, first the total duration of the experiment was discretized to a temporal resolution of 0.05 h (3 min.) and the respective relative tracer concentration/cumulative tracer mass was calculated by linear interpolation between each of the two consecutive measurements. The arithmetic average of the interpolated relative tracer concentration/cumulative tracer mass for each field at respective times provided the field-average BTCs. The breakthrough curves of all the soil for the six fields are presented in Supplementary Fig. 3.
Visible–near-infrared measurements and analysis
The spectra of the soils were measured using a benchtop spectrometer (NIRS DS2500, FOSS, Hillerød, Denmark) (Supplementary Fig. 4). The equipment measures diffuse reflectance within the spectral range of 400–2500 nm with a resolution of 0.5 nm. The instrument was calibrated by scanning a white reference prior to the measurements of the soil samples. About 50 g of air-dried and sieved ( ≤ 2 mm) soil was mixed properly and placed in a rotating quartz sample cup of 70 mm diameter so that the soil completely covered the base of the cup. As the sample cup rotates, the instrument measures the diffuse reflectance four times at seven different positions. The spectral reflectance for each sample is thus an average of 28 spectral measurements. The complete measurement takes about 30 s. The instrument automatically converts the diffuse reflectance (R) measurements into absorbance (A) measurements using the relation A = log (1/R).
The analysis of the vis–NIR data was performed using the “pls package”46 in R software. The arrival times of various fractions of the tracer (5, 10, 15, 20, 25, 30 and 50% denoted by T5–50, respectively) obtained from the BTCs were predicted using vis–NIR spectral data and partial least squares regression (PLSR) after spectral-pretreatment. The spectral pretreatment included performing second-derivative of the spectra with a gap size of w = 5–25 and a segment size of s = 2–31 for different arrival times (Supplementary Table 2). The gap size denotes the number of data points across which the derivative is taken and the segment, s, is the number of data points/segments across which smoothing/averaging is performed prior to derivative47. The prediction was done using a 10-fold cross-validation on the pretreated spectra after obtaining the optimum number of latent variables. In addition, prediction of the arrival times was also obtained by first dividing the total dataset into a calibration (121 samples) and validation (60 samples) dataset. Then the models developed from the calibration dataset were used for predicting the arrival times for the validation dataset. The results for the calibration-validation are presented in the supplementary section (Supplementary Figs 7 and 8; Supplementary Tables 1 and 2). The root mean square error of cross-validation (RMSECV) between the estimated values and the measured values, the coefficient of determination (R2), the ratio of performance (RMSECV) to interquartile range (RPIQ)48 and the bias between the measured and the predicted values were calculated to evaluate the prediction performance.
Tilman, D., Cassman, K. G., Matson, P. A., Naylor, R. & Polasky, S. Agricultural sustainability and intensive production practices. Nature 418, 671, https://doi.org/10.1038/nature01014 (2002).
Carvalho, F. P. Pesticides, environment, and food safety. Food and Energy Security 6, 48–60, https://doi.org/10.1002/fes3.108 (2017).
Epstein, L. Fifty Years Since Silent Spring. Annual Review of Phytopathology 52, 377–402, https://doi.org/10.1146/annurev-phyto-102313-045900 (2014).
European Union. Directive 2006/118/EC of the European Parliament and of the Council of 12 December 2006 on the protection of groundwater against pollution and deterioration. Official Journal of the European Union. Official Journal of the European Union L372 49, 19-31 (2006).
Dominati, E., Patterson, M. & Mackay, A. A framework for classifying and quantifying the natural capital and ecosystem services of soils. Ecol Econ 69, 1858–1868, https://doi.org/10.1016/j.ecolecon.2010.05.002 (2010).
Blum, W. H. Functions of Soil for Society and the Environment. Rev Environ Sci Biotechnol 4, 75–79, https://doi.org/10.1007/s11157-005-2236-x (2005).
Hatfield, J. L., Sauer, T. J. & Cruse, R. M. Chapter One - Soil: The Forgotten Piece of the Water, Food, Energy Nexus in Advances in Agronomy Vol. 143 (ed. Donald L. Sparks) 1–46 (Academic Press, 2017).
Adhikari, K. & Hartemink, A. E. Linking soils to ecosystem services — A global review. Geoderma 262, 101–111, https://doi.org/10.1016/j.geoderma.2015.08.009 (2016).
de Jonge, L. W., Moldrup, P. & Schjønning, P. Soil Infrastructure, Interfaces & Translocation Processes in Inner Space (‘Soil-it-is’): towards a road map for the constraints and crossroads of soil architecture and biophysical processes. Hydrology and Earth System Sciences 13, 1485–1502 (2009).
Bronick, C. J. & Lal, R. Soil structure and management: a review. Geoderma 124, 3–22, https://doi.org/10.1016/j.geoderma.2004.03.005 (2005).
Köhne, J. M., Köhne, S. & Šimůnek, J. A review of model applications for structured soils: b) Pesticide transport. Journal of Contaminant Hydrology 104, 36–60, https://doi.org/10.1016/j.jconhyd.2008.10.003 (2009).
Hendrickx, J. M. H. & Flury, M. Uniform and preferential flow mechanisms in the vadose zone in Conceptual Models of Flow and Transport in the Fractured Vadose Zone 149–188 (The National Academies Press, 2001).
Van Looy, K. et al. Pedotransfer Functions in Earth System Science: Challenges and Perspectives. Rev Geophys, 2017RG000581, https://doi.org/10.1002/2017RG000581 (2017).
Vereecken, H. et al. Modeling Soil Processes: Review, Key Challenges, and New Perspectives. Vadose Zone J 15, https://doi.org/10.2136/vzj2015.09.0131 (2016).
Minasny, B. & Perfect, E. Solute adsorption and transport parameters in Developments in Soil Science Vol. 30 195–224 (Elsevier, 2004).
Viscarra Rossel, R. A. et al. A global spectral library to characterize the world’s soil. Earth-Sci Rev 155, 198–230, https://doi.org/10.1016/j.earscirev.2016.01.012 (2016).
Ben-Dor, E. & Banin, A. Near-Infrared Analysis as a Rapid Method to Simultaneously Evaluate Several Soil Properties. Soil Sci Soc Am J 59, https://doi.org/10.2136/sssaj1995.03615995005900020014x (1995).
Stenberg, B., Viscarra Rossel, R. A., Mouazen, A. M. & Wetterlind, J. Visible and Near Infrared Spectroscopy in Soil Science. Advances in Agronomy 107, 163–215, https://doi.org/10.1016/s0065-2113(10)07005-7 (2010).
McBratney, A. B., Minasny, B. & Viscarra Rossel, R. Spectral soil analysis and inference systems: A powerful combination for solving the soil data crisis. Geoderma 136, 272–278, https://doi.org/10.1016/j.geoderma.2006.03.051 (2006).
Babaeian, E. et al. A Comparative Study of Multiple Approaches for Predicting the Soil–Water Retention Curve: Hyperspectral Information vs. Basic Soil Properties. Soil Sci Soc Am J 79, 1043, https://doi.org/10.2136/sssaj2014.09.0355 (2015).
Santra, P. et al. Estimation of soil hydraulic properties using proximal spectral reflectance in visible, near-infrared, and shortwave-infrared (VIS–NIR–SWIR) region. Geoderma 152, 338–349, https://doi.org/10.1016/j.geoderma.2009.07.001 (2009).
Brusseau, M. L. & Rao, P. S. C. Modeling solute transport in structured soils: a review. Geoderma 46, 169–192, https://doi.org/10.1016/0016-7061(90)90014-z (1990).
Gerke, H. H. Preferential flow descriptions for structured soils. J Plant Nutr Soil Sc 169, 382–400, https://doi.org/10.1002/jpln.200521955 (2006).
Jarvis, N., Larsbo, M., Roulier, S., Lindahl, A. & Persson, L. The role of soil properties in regulating non-equilibrium macropore flow and solute transport in agricultural topsoils. Eur J Soil Sci 58, 282–292, https://doi.org/10.1111/j.1365-2389.2006.00837.x (2007).
Koestel, J. & Jorda, H. What determines the strength of preferential transport in undisturbed soil under steady-state flow? Geoderma 217–218, 144–160, https://doi.org/10.1016/j.geoderma.2013.11.009 (2014).
Koestel, J. K., Moeys, J. & Jarvis, N. J. Meta-analysis of the effects of soil properties, site factors and experimental conditions on solute transport. Hydrology and Earth System Sciences 16, 1647–1665, https://doi.org/10.5194/hess-16-1647-2012 (2012).
Larsbo, M., Koestel, J., Kotterer, T. & Jarvis, N. Preferential Transport in Macropores is Reduced by Soil Organic Carbon. Vadose Zone J 15, 7, https://doi.org/10.2136/vzj2016.03.0021 (2016).
Larsbo, M., Koestel, J. & Jarvis, N. Relations between macropore network characteristics and the degree of preferential solute transport. Hydrology and Earth System Sciences 18, 5255–5269, https://doi.org/10.5194/hess-18-5255-2014 (2014).
Koestel, J. K. et al. Links between soil properties and steady-state solute transport through cultivated topsoil at the field scale. Water Resour Res 49, 1–19, https://doi.org/10.1002/wrcr.20079 (2013).
Paradelo, M. et al. X-ray CT-Derived Soil Characteristics Explain Varying Air, Water, and Solute Transport Properties across a Loamy Field. Vadose Zone J. 15, https://doi.org/10.2136/vzj2015.07.0104 (2016).
Katuwal, S., Moldrup, P., Lamande, M., Tuller, M. & de Jonge, L. W. Effects of CT Number Derived Matrix Density on Preferential Flow and Transport in a Macroporous Agricultural Soil. Vadose Zone J 14, https://doi.org/10.2136/vzj2015.01.0002 (2015).
Naveed, M. et al. Revealing Soil Structure and Functional Macroporosity along a Clay Gradient Using X-ray Computed Tomography. Soil Sci Soc Am J 77, 403–411, https://doi.org/10.2136/sssaj2012.0134 (2013).
Karup, D. et al. Water and solute transport in agricultural soils predicted by volumetric clay and silt contents. Journal of Contaminant Hydrology 192, 194–202, https://doi.org/10.1016/j.jconhyd.2016.08.001 (2016).
Viscarra Rossel, R. A., Walvoort, D. J. J., McBratney, A. B., Janik, L. J. & Skjemstad, J. O. Visible, near infrared, mid infrared or combined diffuse reflectance spectroscopy for simultaneous assessment of various soil properties. Geoderma 131, 59–75, https://doi.org/10.1016/j.geoderma.2005.03.007 (2006).
Knadel, M., Viscarra Rossel, R. A., Deng, F., Thomsen, A. & Greve, M. H. Visible–Near Infrared Spectra as a Proxy for Topsoil Texture and Glacial Boundaries. Soil Sci Soc Am J 77, https://doi.org/10.2136/sssaj2012.0093 (2013).
Clark, R. N. in Remote sensing for the earth sciences: manual of remote sensing. Vol. 3 (ed. A. N. Rencz) 3–58 (John Wiley and Sons., New York., 1999).
Ben-Dor, E. Quantitative remote sensing of soil properties in Advances in Agronomy Vol. 75 (ed. D. L. Sparks) 173–243 (Elsevier Academic Press Inc, 2002).
Pringle, M. J., Romano, N., Minasny, B., Chirico, G. B. & Lark, R. M. Spatial evaluation of pedotransfer functions using wavelet analysis. J Hydrol 333, 182–198, https://doi.org/10.1016/j.jhydrol.2006.08.007 (2007).
Soares, A. et al. Effects of Soil Compaction and Organic Carbon Content on Preferential Flow in Loamy Field Soils. Soil Sci 180, 10–20, https://doi.org/10.1097/ss.0000000000000105 (2015).
Norgaard, T. et al. Comparative Mapping of Soil Physical–Chemical and Structural Parameters at Field Scale to Identify Zones of Enhanced Leaching Risk. J Environ Qual 42, 271–283 (2013).
Minasny, B. & McBratney, A. B. The efficiency of various approaches to obtaining estimates of soil hydraulic properties. Geoderma 107, 55–70, https://doi.org/10.1016/S0016-7061(01)00138-0 (2002).
Ben Dor, E., Ong, C. & Lau, I. C. Reflectance measurements of soils in the laboratory: Standards and protocols. Geoderma 245–246, 112–124, https://doi.org/10.1016/j.geoderma.2015.01.002 (2015).
Lindhardt, B. et al. The Danish Pesticide Leaching Assessment Programme: Site Characterization and Monitoring Design. (Geological Survey of Denmark and Greenland,2001, Copenhagen, Denmark, 2001).
Masís-Meléndez, F., Chamindu Deepagoda, T. K. K., de Jonge, L. W., Tuller, M. & Moldrup, P. Gas diffusion-derived tortuosity governs saturated hydraulic conductivity in sandy soils. J Hydrol 512, 388–396, https://doi.org/10.1016/j.jhydrol.2014.02.063 (2014).
Gee, G. W. & Or, D. Particle-size analysis in Methods of soil analysis. Part 4, Physical methods (eds J. H. Dane et al.) 255–293 (Soil Science Society of America, 2002).
Mevik, B.-H. & Wehrens, R. The pls Package: Principal Component and Partial Least Squares Regression in R. 2007(18), 23, https://doi.org/10.18637/jss.v018.i02 (2007).
Norris, K. Applying Norris Derivatives. Understanding and correcting the factors which affect diffuse transmittance spectra. NIR news 12, 6–9 (2001).
Bellon-Maurel, V., Fernandez-Ahumada, E., Palagos, B., Roger, J.-M. & McBratney, A. Critical review of chemometric indicators commonly used for assessing the quality of the prediction of soil attributes by NIR spectroscopy. TrAC Trends in Analytical Chemistry 29, 1073–1081, https://doi.org/10.1016/j.trac.2010.05.006 (2010).
The authors gratefully acknowledge the funding from Aarhus University Research Foundation (grant no. AUFF-E-2016-9-36).
The authors declare no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
About this article
Cite this article
Katuwal, S., Knadel, M., Moldrup, P. et al. Visible–Near-Infrared Spectroscopy can predict Mass Transport of Dissolved Chemicals through Intact Soil. Sci Rep 8, 11188 (2018). https://doi.org/10.1038/s41598-018-29306-9
Exploring relevant wavelength regions for estimating soil total carbon contents of rice fields in Madagascar from Vis-NIR spectra with sequential application of backward interval PLS
Plant Production Science (2020)
Comparison of spectral and spatial-based approaches for mapping the local variation of soil moisture in a semi-arid mountainous area
Science of The Total Environment (2020)
Predicting glyphosate sorption across New Zealand pastoral soils using basic soil properties or Vis–NIR spectroscopy
Predicting the dry bulk density of soils across Denmark: Comparison of single-parameter, multi-parameter, and vis–NIR based models
Estimating Soil Particle Density using Visible Near-infrared Spectroscopy and a Simple, Two-compartment Pedotransfer Function
Soil Science Society of America Journal (2019)