Abstract
Carbonaceous particulate matter (PM), comprising black carbon (BC), primary organic aerosol (POA) and secondary organic aerosol (SOA, from atmospheric aging of precursors), is a highly toxic vehicle exhaust component. Therefore, understanding vehicle pollution requires knowledge of both primary emissions, and how these emissions age in the atmosphere. We provide a systematic examination of carbonaceous PM emissions and parameterisation of SOA formation from modern diesel and gasoline cars at different temperatures (22, −7 °C) during controlled laboratory experiments. Carbonaceous PM emission and SOA formation is markedly higher from gasoline than diesel particle filter (DPF) and catalyst-equipped diesel cars, more so at −7 °C, contrasting with nitrogen oxides (NOX). Higher SOA formation from gasoline cars and primary emission reductions for diesels implies gasoline cars will increasingly dominate vehicular total carbonaceous PM, though older non-DPF-equipped diesels will continue to dominate the primary fraction for some time. Supported by state-of-the-art source apportionment of ambient fossil fuel derived PM, our results show that whether gasoline or diesel cars are more polluting depends on the pollutant in question, i.e. that diesel cars are not necessarily worse polluters than gasoline cars.
Similar content being viewed by others
Introduction
Most carbonaceous PM from passenger cars is SOA1,2,3,4, known to contain harmful reactive oxygen species5 and damage lung tissue6. However, despite extensive investigation of diesel car pollution7, the relative contributions of diesel and gasoline cars to ambient SOA remains unquantified. While current EU-average passenger car fleet PM emission factors are much higher for diesel than gasoline8, these values are skewed by older vehicles and do not reflect the impacts of the latest generation of after-treatment devices. Diesel passenger cars sold today in the EU/US have diesel particle filters (DPF)9, a wall-flow filter often coated or associated with an oxidation catalyst. Therefore, in order to assess the relative merits of different engine technologies and mitigate vehicle pollution, knowledge of the primary emissions and SOA formation from modern passenger cars equipped with the newest after-treatment technologies is required.
While previous studies have investigated carbonaceous aerosol emission/formation from vehicles via a bottom-up approach (laboratory quantification of tailpipe emissions)1, 10 or top-down source apportionment approaches11, here we combine both. We quantify carbonaceous PM from modern passenger cars (Euro 5 gasoline and DPF-equipped diesel, see Supplementary Information (SI) Table S1 for pollutant limit values). We then constrain our measurements using state-of-the-art source apportionment investigations, providing a comprehensive assessment of the current state and future trends in gasoline and diesel vehicular pollution. Further, we present laboratory measurements of gasoline car SOA formation at low temperatures (−7 °C), in addition to measurements at 22 °C. Low temperatures significantly increase vehicle total hydrocarbon (THC) emission12, 13, including SOA precursors, and favour condensation of gases to the aerosol phase14. With these measurements, we parameterise vehicular SOA formation, accounting for the full range of relevant ambient temperatures, background OA concentrations, and extent of atmospheric aging. This parametrisation method is new and, critically, does not require direct knowledge of precursor composition (which typically includes unknown and/or unquantifiable gases).
Figure 1 shows the experimental set-up used in this study, while details of instrumentation, the test fleet, and smog chamber experimental conditions are given in SI Tables S2–5. Figure 2a shows a comparison of emission factors (EF, g carbon (C) kg−1 fuel) of carbonaceous aerosol and SOA formation during the New European Driving Cycle (NEDC, SI Fig. S1, from in-use Euro 5 gasoline and DPF-equipped-diesel passenger cars, measured in a smog chamber4. DPF-equipped-diesel car EFs are orders of magnitudes below inventory values (0.68–2.64 g kg−1 fuel)8 and far below those reported for older non-DPF-equipped passenger cars3, 15, while gasoline cars are comparable to inventory values (0.01–0.04 g kg−1 fuel). The gasoline cars emitted on average 10 times more carbonaceous aerosol at 22 °C and 62 times more at −7 °C compared to diesel cars, mainly due to substantially higher BC, with EF at −7 °C comparable to those from old diesel. Low temperatures dramatically increased primary emissions and secondary carbonaceous aerosol formation from the gasoline cars but not diesel. Strikingly, for one gasoline car, BC emissions were at least 400 times higher than from the diesels (comparing to the detection limit). The increase in the emissions at lower temperatures is related to a more pronounced cold start effect likely resulting from (1) a poorer combustion efficiency following energy loss to cold engine surfaces and increased friction due to lubricants being too viscous at low temperatures; and of (2) an extended delay before catalyst light-off. These factors tend to be more important in gasoline vehicles than diesel vehicles16, 17. The diesel cars emitted 10 times more NOX at both temperatures. Real world vehicle emissions of NOX tend to differ from laboratory results18, 19. Importantly however, such biases are not expected for other pollutants, e.g. THC20. If SOA were to be added to the primary emissions, the inventory values for the gasoline cars would be exceeded by far: Emissions from new gasoline cars (both EU and US) produce up to 6.5 times more SOA than POA after 5–10 hours of atmospheric aging2. Meanwhile, the new diesel cars produced no detectable SOA, contrasting with old diesels, for which SOA production is about equal to emitted POA3. The absence of observed SOA from the DPF-diesels is explained by the chemical composition of the THC emissions; while emissions from non-DPF-diesels chemically resemble diesel vapours21, DPF-equipped-diesel exhaust comprises a large fraction (>70%) of short-chain oxygenated compounds, mainly formaldehyde and acetaldehyde, which are much less efficient SOA precursors than the aromatic species found in gasoline emissions (Fig. 3c). These results challenge the existing paradigm that diesel cars are associated, in general, with far higher PM emission rates8, reflecting the effectiveness of recent, Euro 5–6, diesel after-treatments such as DPFs combined with diesel oxidation catalysts. Furthermore, while Gordon et al.3 report primary PM emissions (g kg−1 fuel) during DPF regeneration (burn-off of accumulated PM) similar to those during regular driving of a non-DPF vehicle, DPF regeneration is activated infrequently (every few hundred km), lasts around one minute, and is more likely to occur at high speed (more likely outside densely populated areas). Thus, the net result of regeneration is unlikely to significantly diminish DPF efficacy. For all emission factors and SOA production factors for the different tests (including in g km−1), please see SI Tables S6–7.
Figure 3 shows that SOA yields (ΔSOA/ΔTHC) for gasoline passenger cars are higher at −7 compared to 22 °C and exceed those of both raw gasoline and pure single-ring aromatic hydrocarbons. These yields were determined using a new methodology, as described in the SI. We also estimated an effective enthalpy of vaporisation (encompassing the effect of non-ideal mixing) of 19 kJ mol−1, and a change in yield of 2 ± 0.4% K−1. For SOA yields as a function of temperature and suspended OA concentrations, please see SI Fig. S6. Since gasoline cars produced SOA whereas the DPF-equipped diesels did not, the expectation is that gasoline passenger cars should dominate urban vehicular SOA11, 22,23,24. However not all studies agree, for example Gentner et al.25 suggest that diesel vehicles produce more SOA since 1) most THC along a highway comes from diesels and 2) exhaust THC is similar to vaporised fuel, for which diesel SOA yields are higher (Fig. 3). One explanation for this may be that assumption 1 is invalid for newer vehicles, since the THC composition from new diesels comprises a large fraction of low molecular weight carbonyls not present in raw diesel fuel (Fig. 2). Another explanation may be that roadside measurements do not capture the large cold-start related emissions of THC from gasolines likely occurring before reaching major highways (Fig. 4). Our results show that emissions from vehicles are sensitive to sampling location, fleet age and ambient temperature, implying that regional studies representing an aggregate of emissions are likely to produce better estimates of the relative importance of diesel vs. gasoline to ambient SOA than roadside studies at one location.
We further show that gasoline vehicle SOA can comprise a large, sometimes dominant fraction of vehicle SOA by modelling ambient SOA from gasoline and old diesel cars in the L.A. region (Fig. 5a, see also SI materials) and comparing the result to observed ambient fossil fuel-related SOA (f SOA)24, 26, 27. We use toluene as a tracer for gasoline car emissions and the yields from our smog chamber experiments, since Borbon et al.28 demonstrate that traffic is the predominant source of toluene in L.A. based on the toluene to CO ratio, while our own experiments show minimal toluene emission from diesel. Furthermore, Baker et al.6, 29 show that during the CALNEX campaign, and using emission inventory data, non-vehicular point sources account for 12% and 6% of benzene + toluene + xylenes (BTEX) in Bakersfield and Pasadena, respectively.
Modelled SOA fits within uncertainties the measured f SOA assuming yields from LEV1/LEV2/Euro 5, while gasoline emissions alone may explain up to 82% of observed f SOA. Meanwhile, the estimated contribution from diesel is significantly lower. While we do not achieve closure with the ambient data, the important information is the split between f SOA from gasoline and diesel vehicles showing that gasoline is the larger fraction. This conclusion agrees with ambient observations of fossil fuel-related aerosol in European cities and the US (Fig. 5b). POA and BC are the largest fraction of carbonaceous PM in Europe, consistent with a higher share of diesel cars. At these locations, f SOA is likely mainly from non-DPF diesel emissions, assuming it is approximately equal to diesel POA emissions12. In the US, where cars are almost exclusively gasoline powered, SOA is the dominant fraction of carbonaceous PM, as would be expected from the bottom-up estimations in Fig. 5a. Therefore, in combination, the laboratory SOA yields and ambient measurements suggest a large and likely increasingly dominant fraction of carbonaceous aerosol is from gasoline passenger cars in the US, while in Europe, old non-DPF diesels still dominate the carbonaceous aerosol burden.
We emphasise that since PM emissions are much higher from diesel cars without a DPF, diesel passenger car carbonaceous emissions will continue to be important for some time. Figure 5c shows an estimation of the impact of a gradual phase-in of DPFs on the fraction of primary vehicular PM from diesel30. A projection for the EU, shown in blue, suggests an initial increase in the share of primary PM from diesel vehicles, followed by a decrease as DPFs become widespread. Adoption of electric vehicles does not alter the conclusions, as they do not affect the relative contribution from either gasoline or diesel passenger cars. Results show that in the presence of only 3% of non-DPF diesel cars, diesel cars would still dominate car primary carbonaceous emissions, in the EU in warm conditions. Meanwhile, during winter, gasolines may already dominate passenger car carbonaceous PM at present.
Higher carbonaceous aerosol production from modern gasoline cars has been observed in tests on US registered vehicles, and in this work for European vehicles. In all of our tests, modern gasoline cars produced more carbonaceous aerosol than modern DPF-equipped diesels. This was true when considering primary particulates only, but the difference is larger when considering the additional SOA production from gasolines, and even larger when considering the effect of low temperatures on emissions. We also show that these measurements are consistent with ambient observations of high fossil SOA fractions in areas with a high fraction of gasoline cars. Our results suggest that as vehicle fleets modernise to include a higher fraction of DPF-diesels the relative contribution from gasoline passenger cars to carbonaceous aerosol will increase. Note that while we draw these conclusions from driving cycles designed to represent real-world driving and from ambient data reflecting an aggregate of all emissions, exceptions are possible. Critically, how much of the carbonaceous aerosol in any region is from one engine technology or the other will depend on the number of vehicles with each type of engine technology in operation and the age of the vehicles (i.e. the number of old, non-DPF vs modern, DPF equipped diesels), which may be region-dependent. Specific cases where diesel passenger cars may emit more carbonaceous aerosol than gasoline may include very long journeys (relative importance of the cold start is lower), operating conditions not investigated here e.g. high speeds (>120 km h−1) or extremes of temperature, and outlier vehicles (note the very large ranges in emissions in e.g. Fig. 4). Nevertheless, and since NOX emissions are generally higher from diesel cars, there is a choice between new passenger cars that generally emit less PM and produce less SOA (diesel), or new passenger cars that emit less NOX (gasoline).
Methods
Vehicle testing procedure
Experiments were performed at the Vehicle Emissions Laboratory (VELA) of the European Commission Joint Research Centre as described in Platt et al.4. The climatic test cell (−10 °C to 35 °C temperature range) features two 48″ roller benches (Maha, Germany) and a dilution tunnel (Horiba, Japan) for a constant volume sampler (CVS, average dilution = 40). Gaseous emissions from the vehicles described in SI Tables S3 and S4 were sampled, diluted and collected in Tedlar bags for analysis with an integrated total hydrocarbon analyser (Horiba MEXA 7400 HTRLE) following Directive 70/220/EEC31 and its following amendments. Particles were collected from the CVS onto heated filters (Horiba HFU-4770) and measured offline gravimetrically at ambient temperature and directly after the test. Vehicles were driven over the New European Driving Cycle (see SI Fig. 1 and EU Regulation 692/2008 ref. 32) at −7 °C and 22 °C after at least 6 hours soak time at the same temperature of the emission test. Regulated gaseous compounds were measured with the following techniques: total hydrocarbons (THC) with gas chromatography and flame ionization detection GC-FID, carbon monoxide and dioxide (CO, CO2) with non-dispersive infrared, nitrogen oxides (NOX) with chemiluminescence. In parallel to diluted sampling necessary to fulfil the legislative requirements, we characterised the raw exhaust in real-time (at 1 Hz) during the driving cycles with the same techniques described above. Procedures such as pre- and post-test flushing (30 minutes each) of the transfer lines and dilution tunnel were automatically executed to assure monitored background concentrations below the respective detection limits.
Smog chamber experimental procedure
Smog chamber experiments are listed in SI Table S5. Prior to all experiments the mobile chamber is cleaned by reducing its volume to ~1 m3 and flushing first with ozone (O3) and humidified air, illuminating the chamber with UV light for a period of around 1 hour and then flushing with pure dry air for several hours overnight. At the start of each experiment, the bag was filled to approximately two thirds full with humidified air (i.e. leaving a volume free for sample injection during several minutes). Emissions were then sampled directly at the vehicle tailpipe during the NEDC and injected into the chamber using the Dekati ejector dilutor. Dilution provided by the Dekati was ~12, subsequently increased to ~150 by the air inside the smog chamber. The Dekati and sampling lines were heated to 150 °C. Sampling lines are constructed from silica steel. Subsequent to exhaust injection, the chamber was filled to close to maximum volume with pure air. A period of several minutes was allowed for the equilibration inside the chamber and for characterization of the primary emissions. Ozone was added to the chamber to titrate NO emitted by the vehicles to NO2. This ensured that conditions were more representative of the troposphere where most NOX is in the form of NO2 and increased the reactivity of the gases in the chamber; previous studies have demonstrated that SOA formation only begins following conversion of NO to NO2 4, 33. Note that only enough O3 was added to convert the NO, and that an excess was not present before lights-on.
For two experiments (gasoline vehicle 1, Table S5) propene was added prior to lights on in order to adjust the VOC to NOX ratio (with the assumption that propene itself does not form SOA) to enhance OH concentrations, as discussed in Platt et al.4. For all subsequent experiments nitrous acid (HONO) was added to the chamber via a constant injection stream34 to increase OH radical concentrations. Since significant NOX was present in the chamber during all experiments, and since HONO was added, we assume that all experiments were under high NOX conditions. 1 µL (~20 ppbv) of nine-times deuterated butanol (butanol-D9, 98% Aldrich) was injected prior to lights on to quantify OH exposure during the experiments35. Butanol-D9 is a unique OH tracer, and measuring its decay, here with the proton transfer reaction time-of-flight mass spectrometer (PTR-ToF-MS), yields time resolved OH concentrations. Following adjustment of the gases, and characterization of the primary emissions, the smog chamber lights were switched on for a period of ~4 hours to initiate photochemistry.
Time-resolved online measurements of particle composition were performed using a high-resolution time-of- flight aerosol mass spectrometer (HR-ToF-AMS, Aerodyne) for organics, nitrate, and ammonium, and an aethalometer (Model AE33, Aerosol d.o.o.) for equivalent black carbon (BC). A detailed description of the working principles of the HR-ToF-AMS and associated data analysis may be found in DeCarlo et al.36. Data from the HR-ToF-AMS were analysed using high-resolution analysis fitting procedures. Volume data from integrated scanning mobility particle sizer (SMPS, custom built) data from the chamber were transformed into mass concentrations using densities based on the particle chemical composition measured by the HR-ToF-AMS and subtracting BC, to provide a second measurement of the total non-refractory PM mass (i.e. those species quantified in the HR-ToF-AMS). This was used to correct for collection efficiency, CE, which was between 0.5–1.0 throughout all experiments where the non-refractory mass was above detection limit. HR-ToF-AMS data were corrected for background CO2 by calibrating the observed CO2 in filtered air to external measurements using a cavity ring-down spectrometer (G2401, Picarro).
A correction was applied to the OA mass to account for HR-ToF-AMS measurement interferences of organic aerosol mass in presence of ammonium nitrate (NH4NO3). As detailed in Pieber et al.37, nitrate salts interfere with the measurement of particulate CO2 +, by creating an oxidising environment on the particle vaporiser in the HR-ToF-AMS, thereby releasing CO2 + from carbonaceous residues. We use the proportional relationship K between the measured CO2 + and the NH4NO3 mass measured during instrument calibrations for data correction. The fractional contribution K is linked to the actual NO3 mass as a function of time t during sampling to determine the absolute contribution of interference based CO2 + (K × measured_NO3) to the real organic mass observed as CO2 + ion:
A K value 3–5% was applied based on information gained during instrument calibrations.
Primary aerosol emission was determined from the concentrations in the chamber after the driving cycle was finished and as soon as the CO2 signal was stable. Figure S2 shows a comparison of primary mass measured at the chamber (sum of BC and OC) and at the VELA from the CVS. The smog chamber primary aerosol is generally lower than the gravimetric measurements as might be expected since 1) primary emission includes more species than carbonaceous aerosol, e.g. metals, 2) particle losses to the chamber walls during the driving cycles and equilibration period cannot be/are not corrected for, and 3) gravimetric measurements may be affected by adsorption artefacts. Secondary aerosol mass was determined from the increase in OA observed after lights on. The suspended OA concentration COA is corrected for wall losses (COA, WLC) assuming material lost to the walls does not partition using:
Where COA,SUSP is the OA at time = t and k an exponential decay constant taken from an exponential fit of BC (determined at λ = 950 nm).
Gas phase composition was measured using a suite of dedicated instruments as also described in Platt et al.4. Oxygenated VOCs were monitored with the PTR-ToF-MS. The instrument was operated at standard conditions, with a reaction chamber pressure fixed at 2.1 mbar, drift tube voltage and temperature at 500 V and 333 K, respectively, corresponding to an electric field strength applied to the drift tube (E) to buffer gas density (N) ratio of 125 Td. CO2, CH4 and CO were quantified with the Picarro and total hydrocarbons (THC) were measured with a flame ionization detector (Horiba, THC Monitor APHA-370). The raw THC signal from the smog chamber, [THC]un, is corrected to yield [THC]cor, for response factors, RF, of ethanol, acetaldehyde, and formaldehyde12 as observed by the PTR-ToF-MS as using:
Several smog chamber experiments were performed where no aging data were obtained (e.g. for G1 at −7 °C), but where data on the primary emission, e.g. from the VELA, were still accessible.
Emission factors (EF) are determined using a carbon mass balance:
where P is the species of interest, ωc the carbon fraction of the fuel and CO2 and CO are in units of carbon mass.
References
Gentner, D. R. et al. A review of urban secondary organic aerosol formation from gasoline and diesel motor vehicle emissions. Environmental Science and Technology 51, 1074–109 (2017).
Gordon, T. et al. Secondary organic aerosol formation exceeds primary particulate matter emissions for light-duty gasoline vehicles. Atmospheric Chemistry and Physics 14, 4661–4678 (2014).
Gordon, T. et al. Secondary organic aerosol production from diesel vehicle exhaust: impact of aftertreatment, fuel chemistry and driving cycle. Atmospheric Chemistry and Physics 14, 4643–4659 (2014).
Platt, S. M. et al. Secondary organic aerosol formation from gasoline vehicle emissions in a new mobile environmental reaction chamber. Atmospheric Chemistry and Physics 13, 9141–9158 (2013).
Platt, S. et al. Two-stroke scooters are a dominant source of air pollution in many cities. Nature communications 5 (2014).
Künzi, L. et al. Toxicity of aged gasoline exhaust particles to normal and diseased airway epithelia. Scientific reports 5 (2015).
World Health Organisation (WHO). Health effects of black carbon. http://www.euro.who.int/__data/assets/pdf_file/0004/162535/e96541.pdf (2012).
European Environment Agency (EEA). EMEP/CORINAIR 2013 Emission Inventory Guidebook. http://www.eea.europa.eu/publications/emep-eea-guidebook-2013 (2013).
Johnson, T. V. Diesel emission control in review. SAE International Journal of Fuels and Lubricants 1, 68–81 (2008).
Zardini, A. A. et al. Effects of alkylate fuel on exhaust emissions and secondary aerosol formation of a 2-stroke and a 4-stroke scooter. Atmospheric Environment 94, 307–315 (2014).
Hayes, P. et al. Organic aerosol composition and sources in Pasadena, California, during the 2010 CalNex campaign. Journal of Geophysical Research: Atmospheres 118, 9233–9257 (2013).
Clairotte, M. et al. Effects of low temperature on the cold start gaseous emissions from light duty vehicles fuelled by ethanol-blended gasoline. Applied Energy 102, 44–54 (2013).
Suarez-Bertoa, R. et al. Primary emissions and secondary organic aerosol formation from the exhaust of a flex-fuel (ethanol) vehicle. Atmospheric Environment 117, 200–211 (2015).
Donahue, N. M., Robinson, A. L., Stanier, C. O. & Pandis, S. N. Coupled partitioning, dilution, and chemical aging of semivolatile organics. Environmental Science and Technology 40, 2635–2643 (2006).
Chirico, R. et al. Impact of aftertreatment devices on primary emissions and secondary organic aerosol formation potential from in-use diesel vehicles: results from smog chamber experiments. Atmospheric Chemistry and Physics 10, 11545–11563 (2010).
Weilenmann, M., Soltic, P., Saxer, C., Forss, A.-M. & Heeb, N. Regulated and nonregulated diesel and gasoline cold start emissions at different temperatures. Atmospheric environment 39, 2433–2441 (2005).
Roberts, A., Brooks, R. & Shipway, P. Internal combustion engine cold-start efficiency: A review of the problem, causes and potential solutions. Energy Conversion and Management 82, 327–350 (2014).
United Kingdom Department of Transport. Vehicle Emissions Testing Programme 2016. https://www.gov.uk/government/uploads/system/uploads/attachment_data/file/535501/vehicle-emissions-testing-programme-web.pdf (2016).
Baltensperger, U. Spiers Memorial Lecture Introductory lecture: chemistry in the urban atmosphere. Faraday discussions (2016).
Weiss, M., Bonnel, P., Hummel, R., Provenza, A. & Manfredi, U. On-road emissions of light-duty vehicles in Europe. Environmental Science and Technology 45, 8575–8581 (2011).
May, A. A. et al. Gas-and particle-phase primary emissions from in-use, on-road gasoline and diesel vehicles. Atmospheric Environment 88, 247–260 (2014).
Ortega, A. et al. Real-time measurements of secondary organic aerosol formation and aging from ambient air in an oxidation flow reactor in the Los Angeles area. Atmospheric Chemistry and Physics 16, 7411–7433 (2016).
Bahreini, R. et al. Gasoline emissions dominate over diesel in formation of secondary organic aerosol mass. Geophysical Research Letters 39, L06805 (2012).
Ensberg, J. et al. Emission factor ratios, SOA mass yields, and the impact of vehicular emissions on SOA formation. Atmospheric Chemistry and Physics 14, 2383–2397 (2014).
Gentner, D. R. et al. Elucidating secondary organic aerosol from diesel and gasoline vehicles through detailed characterization of organic carbon emissions. Proceedings of the National Academy of Sciences 109, 18318–18323 (2012).
Hayes, P. et al. Modeling the formation and aging of secondary organic aerosols in Los Angeles during CalNex 2010. Atmospheric Chemistry and Physics 15, 5773–5801 (2015).
Zotter, P. et al. Diurnal cycle of fossil and nonfossil carbon using radiocarbon analyses during CalNex. Journal of Geophysical Research: Atmospheres 119, 6818–6835 (2014).
Borbon, A. et al. Emission ratios of anthropogenic volatile organic compounds in northern mid‐latitude megacities: Observations versus emission inventories in Los Angeles and Paris. Journal of Geophysical Research: Atmospheres 118, 2041–2057 (2013).
Baker, K. et al. Gas and aerosol carbon in California: comparison of measurements and model predictions in Pasadena and Bakersfield. Atmospheric Chemistry and Physics 15, 5243–5258 (2015).
Transport & Mobility Leuven. The Tremove model. http://www.tmleuven.be/methode/tremove/home.htm (2010).
The Council of the European Communities. Council Directive 70/220/EEC of 20 March 1970 on the approximation of the laws of the Member States relating to measures to be taken against air pollution by gases from positive-ignition engines of motor vehicles. Official Journal of the European Communities L076, 1–22 (1970).
European Commission. Regulation No 692/2008 of 18 July 2008 implementing and amending Regulation (EC) No 715/2007 of the European Parliament and of the Council on type-approval of motor vehicles with respect to emissions from light passenger and commercial vehicles (Euro 5 and Euro 6) and on access to vehicle repair and maintenance information. Official Journal of the European Communities L199 (2008).
Nordin, E. et al. Secondary organic aerosol formation from idling gasoline passenger vehicle emissions investigated in a smog chamber. Atmospheric Chemistry and Physics 13, 6101–6116 (2013).
Taira, M. & Kanda, Y. Continuous generation system for low-concentration gaseous nitrous acid. Analytical Chemistry 62, 630–633 (1990).
Barmet, P. et al. OH clock determination by proton transfer reaction mass spectrometry at an environmental chamber. Atmospheric Measurement Techniques 5, 647–656 (2012).
DeCarlo, P. F. et al. Field-deployable, high-resolution, time-of-flight aerosol mass spectrometer. Analytical Chemistry 78, 8281–8289 (2006).
Pieber, S. et al. Inorganic Salt Interference on CO2+ in Aerodyne AMS and ACSM organic aerosol composition studies. Environmental Science and Technology 50, 10494–10503 (2016).
Jathar, S. H. et al. Secondary organic aerosol formation from photo-oxidation of unburned fuel: Experimental results and implications for aerosol formation from combustion emissions. Environmental Science and Technology 47, 12886–12893 (2013).
Klaassen, G., Berglund, C. & Wagner, F. The GAINS Model for Greenhouse Gases-Version 1.0: Carbon Dioxide (CO2). IIASA Interim Report IR-05-53. International Institute for Applied Systems Analysis (IIASA), Laxenburg, Austria (2005).
Acknowledgements
This work was supported by the Swiss Federal Office for the Environment (FOEN), the Federal Roads Office (FEDRO), the Swiss National Science Foundation (SNSF) for SAPMAV (No. 200021 13016), WOOSHI (No. 140590), and Ambizione (PZ00P2_131673), and The French Environment and Energy Management Agency (ADEME, Grant numbers 1162C0002 and 1262C0017). The instrumental platform MASSALYA from the Aix-Marseille Université is acknowledged for PTR-ToF-MS measurements. The VELA staff is acknowledged for its skilful technical assistance, in particular Franz Muehlberger, Urbano Manfredi, Mauro Cadario and Philippe Le Lijours. JLJ was supported by CARB 11-305 and EPA STAR 83587701-0. Disclaimer: The opinions expressed in this manuscript by the authors affiliated to the EC-JRC should in no way be considered to represent an official opinion of the European Commission. This manuscript has not been reviewed by the US EPA and no endorsement should be inferred.
Author information
Authors and Affiliations
Contributions
Experimental design: S.M. Platt, I.El.-H., A.S.H.P., C.A., A.A.Z., R.S.-B., M.C., N.M.; experimental work: S.M.Platt, I.El.-H., S.M. Pieber, J.G.S., R.J.H., S.H., A.A.Z., R.S.-B., M.C., B.T.-R.; Data analysis: S.M.Platt, I.El.-H., S.M.Pieber, S.H., B.T.-R., A.A.Z., R.S.-B., M.C.; Analysis and interpretation of CALNEX data: P.H., J.L.J; US vehicle emissions A.R.; SOA yields model: I.El.-H., K.R.D.; manuscript preparation: S.M.Platt, I.El.-H.; Interpretation of results and comments on the manuscript: all.
Corresponding authors
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Platt, S.M., El Haddad, I., Pieber, S.M. et al. Gasoline cars produce more carbonaceous particulate matter than modern filter-equipped diesel cars. Sci Rep 7, 4926 (2017). https://doi.org/10.1038/s41598-017-03714-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-017-03714-9
This article is cited by
-
Characterization and prediction of tailpipe ammonia emissions from in-use China 5/6 light-duty gasoline vehicles
Frontiers of Environmental Science & Engineering (2024)
-
Probabilistic Transport-Induced Emissions and Health Risks for Adelaide, South Australia
Environmental Modeling & Assessment (2024)
-
Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor
Emission Control Science and Technology (2024)
-
A coupled atmospheric simulation chamber system for the production of realistic aerosols and preclinical model exposure
Air Quality, Atmosphere & Health (2024)
-
An investigation on well-to-wheel emissions of passenger cars in Turkey
Environmental Science and Pollution Research (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.