Article | Open

# Synthetic ferrimagnet nanowires with very low critical current density for coupled domain wall motion

• Scientific Reports 7, Article number: 1640 (2017)
• doi:10.1038/s41598-017-01748-7
Accepted:
Published online:

## Abstract

Domain walls in ferromagnetic nanowires are potential building-blocks of future technologies such as racetrack memories, in which data encoded in the domain walls are transported using spin-polarised currents. However, the development of energy-efficient devices has been hampered by the high current densities needed to initiate domain wall motion. We show here that a remarkable reduction in the critical current density can be achieved for in-plane magnetised coupled domain walls in CoFe/Ru/CoFe synthetic ferrimagnet tracks. The antiferromagnetic exchange coupling between the layers leads to simple Néel wall structures, imaged using photoemission electron and Lorentz transmission electron microscopy, with a width of only ~100 nm. The measured critical current density to set these walls in motion, detected using magnetotransport measurements, is 1.0 × 1011 Am−2, almost an order of magnitude lower than in a ferromagnetically coupled control sample. Theoretical modelling indicates that this is due to nonadiabatic driving of anisotropically coupled walls, a mechanism that can be used to design efficient domain-wall devices.

## Introduction

The presence of antiferromagnetic1 and oscillatory2 indirect exchange coupling across a metal spacer between ferromagnetic layers was one of the earliest discoveries in the field of ultrathin film magnetism. The effect can be used to construct synthetic antiferromagnets (SAFs), where the alternating atomic spins are replaced by the alternating moments of magnetic layers3. These structures have found applications as the reference layers in magnetoresistive recording heads4, and in the operation of toggle-mode magnetic random access memory cells5.

Domain walls (DWs) in magnetic nanowires6 have been proposed as the basis of memory7, logic8, 9, and sensor10 technologies. By far the most common choice of material in the past has been Permalloy (Ni80Fe20)11,12,13,14,15. Shape anisotropy means that the domains in such a soft magnetic nanowire have magnetisation that points along the wire length, leading to head-to-head or tail-to-tail DWs. The micromagnetics of these ribbon-shaped wires is such that the walls take non-trivial vortex or transverse forms16. The width of the DWs is tied to the wire geometry17, with very high current densities required to set them in motion using spin-transfer torques18, typically a few 1012 Am−2 (refs 11, 14, 19 and 20). Whilst moving, neither type of wall is a rigid object, since they possess internal degrees of freedom that can dissipate energy21. The stray field from the DWs means that they will also couple if brought too close together22. These drawbacks are all major obstacles to the use of DWs in such nanowires in applications such as racetrack memories7.

One approach to move towards more useful devices is to employ chiral walls23 in ultrathin perpendicularly magnetised layers that possess a Dzyaloshinskii-Moriya interaction. Such walls are narrow, with a simple Néel structure, and couple well to spin-orbit torques24, 25, but still interact with each other by their stray fields. Perpendicularly magnetised SAF wires do not have this drawback, and show very high wall velocities when driven with high current densities but still require at least ~1012 Am−2 current density for the onset of wall motion26.

A structure with unbalanced antiparallel moments is a synthetic ferrimagnet (SyF). Here we show that returning to the use of in-plane magnetised nanowires, formed into SyFs, can mitigate against all of these obstacles. In particular, the threshold current density can be significantly reduced when the combination of isotropic indirect exchange across the Ru spacer and anisotropic magnetostatic coupling between the walls allows the engineering of a situation where the walls are coupled antiferromagnetically in-plane, but ferromagnetically out-of-plane. Within a one-dimensional (1-D) model27, we show that if this out-of-plane ferromagnetic coupling is sufficiently strong, the new internal degrees of freedom in the coupled pair of walls can be exploited to reduce the threshold current density to zero, even in the presence of finite extrinsic pinning. This is due to the coupled wall pair possessing internal degrees of freedom that a wall in single wire does not, which can be exploited to escape the pinning potential. We have tested this experimentally in a CoFe/Ru/CoFe SyF nanowire: measurements of the current-driven domain wall mobility curve in zero magnetic field have shown critical current densities as low as Jcrit ≈ 1.0 × 1011 Am−2. This is less than half the lowest reported critical current density to date, ~2.5 × 1011 A/m2, measured in a Co/Ni multilayer wire in the pure intrinsic pinning regime28. Our work expands the range of possible designs available to engineers when trading off parameters such as speed, density, and power consumption when designing domain wall devices. Such structures are thus good candidates for racetrack memories where power consumption is the most important figure-of-merit.

## Results

### Structure of coupled domain wall pairs in SyFs

In order to study the DW structures in these trilayers, SyF nanowire devices were fabricated as described in the Methods section with the geometry shown in Fig. 1c: a 16 μm long, 400 nm wide nanowire with one pointed end and the other attached to a large elliptical injection pad15. The SyF comprised a Co90Fe10 (t2)/Ru/Co90Fe10 (t1) trilayer. The high-resolution TEM cross-section in Fig. 1b clearly resolves the Ru spacer layer, the 0.7 nm thickness of which is chosen to give strong antiferromagnetic coupling of the two Co90Fe10 layers2, which have thicknesses t1 = 13.3 and t2 = 6.6 nm. We chose to study the unbalanced SyF configuration since magnetic fields may be used to initiate the devices in a controlled magnetisation configuration, due to the fact that the net magnetic moment is not fully compensated.

By analysing the magnetostatics in SyFs it may be shown that elliptical elements have a significantly lower coercivity than rectangular segments29, just as for single ferromagnetic layers30. Coupled pairs of DWs–shown schematically in Fig. 1a –were prepared in the SyF nanostructures by applying a controlled reverse magnetic field to switch the net magnetisation in the elliptical element. This process is shown in Fig. 1c using X-ray magnetic circular dichroism photo-emission electron microscopy (XMCD-PEEM) imaging, accompanied by micromagnetic simulations that reproduce the injection process. The XMCD-PEEM technique is a surface sensitive method, thus the images in Fig. 1c represent the magnetisation direction only in the upper, thicker, Co90Fe10 layer. Initially the devices are saturated with net magnetisation pointing to the left, driven by the magnetisation in the thicker layer responding to the applied field. Longitudinal field pulses up to 100 Oe reverse the net magnetisation in the elliptical element whilst leaving the magnetisation in the nanowire unchanged, generating a coupled pair of DWs at the neck of the elliptical pad. Stronger field pulses propagate the DW along the track, eventually reversing its net magnetisation direction.

A more detailed view of an example of the novel type of DW observed in these structures is shown in the Lorentz transmission electron microscopy (LTEM) image of an 800 nm wide wire and pad shown in Fig. 1d. This image was taken in the defocussed Fresnel mode which is sensitive to gradients in magnetic induction, such as DWs31. We note that in this case the contrast arises from the projected sum of in-plane magnetic induction contributions from both layers. Note that patterned films where the magnetisation is parallel to the edge of the structure also show black/white contrast due to the diverging/converging effect of the electron beam either side of the edge in Fresnel mode. Thus we can observe a white DW running across the wire in Fig. 1d, but in addition we also see a significant change in contrast on the upper edge of the wire either side of the DW. The latter signifies a change of the net magnetic induction either side of this DW.

In order to verify the antiparallel alignment of the Co90Fe10 layers we have investigated the reversal and DW injection mechanism using LTEM in this 800 nm wide wire in greater detail. In the magnetically saturated state shown in Fig. 2a, no DW contrast is visible in the wire itself and here the dark and bright contrast from the opposite edges shows that a net magnetisation exists in the wire which corresponds to both layers having parallel magnetisation. (This is in addition to the normal Fresnel contrast associated with the phase change at an edge which is also visible as a black/white contribution on each edge).

On reduction of the field a 360° DW appears close to the neck of the wire and ellipse region, shown in Fig. 2b. Considering the reversal mode of the SyF structure, where switching into a largely antiparallel state is expected, and comparison with the micromagnetic simulations in the Supplementary information indicates that the 360° DW exists only in the thinner layer, whilst the thicker layer remains uniformly magnetised. Compared to the previous image the magnetic contribution to the edge contrast has been reduced significantly, most notably with the dark contrast visible at the lower edge. This is a consequence of the fact that whilst the majority of the magnetisation remains along the wire axis, the direction in each layer is antiparallel in the domains to either side of the 360° DW, so that the net magnetisation that causes the contrast is smaller than Fig. 2a. The 360° DW traverses the width of the wire, showing a distinct black/white character indicative of strong transverse magnetisation at the centre of the wall. Furthermore the magnetic contrast associated with the nanowire edges does not change either side of the wall, which is consistent with the wall being only in one layer therefore the net magnetisation either side of the wall is the same.

Further variation of the field sees the injection of a coupled pair of 180° DWs, one in each layer lying on top of each other, as shown in Fig. 2c, which come to rest a short distance from the neck. Again, the coupled walls traverse the width of the wire. The edge contrast can again be seen to be much weaker than in Fig. 2a, the parallel arrangement, and in fact is similar to the antiparallel arrangement in Fig. 2b. However the edge contrast can clearly be seen to change either side of the wall. This is most apparent in the upper edge, which is darker on the left hand side of the wall compared to right hand side. This is consistent with an antiparallel arrangement on each side of the coupled DW pair, but with a net magnetisation in the opposite direction for each side, reflecting the imbalance of the layer thickness. This analysis also holds for the image presented in Fig. 1d, and we can see that there is no overlapping parallel region in either case32. This confirms that there truly is a pair of AFM-coupled 180° DWs in both cases. The coupled pair of DWs is eliminated by a further increase in the field as shown in Fig. 2d. Here the weak magnetic edge contrast is consistent with a fully antiparallel alignment of the layers. In fact the antiparallel configurations in Fig. 2b and d are seen to have a net alignment in different directions from the change in upper edge contrast, this can be seen from the schematic arrows indicated for each layer underneath the figures. Note that the fact that the edge contrast between these two figures is not exactly equal and opposite reflects a degree of strucutural edge asymmetry due to lithographic flagging that is not exactly the same on both wire edges.

The high degree of flux closure in the SyF trilayer entirely changes the micromagnetics of the DWs meaning that the usual vortex/transverse wall picture16 for single nanowires is substantially changed. Instead, these walls have a simple Néel form, with the wall widths measured from the Fresnel images in Fig. 2b and c being 110 ± 15 nm: the width is also found to be independent of the wire geometry due to the changed magnetostatics. It should be noted that the widths measured here by the defocussed Fresnel method correspond to an upper limit for the widths of the domain walls. Micromagnetic simulations of DW structures in SAF and SyF Co90Fe10 tracks, with track widths from as small as 40 nm up to 1.2 μm, have shown that narrow symmetric transversely magnetised Néel walls, with width ~100 nm, persist, in marked contrast to single layer ferromagnetic tracks33. This is due to the fact that the transverse demagnetising field, normally responsible for deforming symmetric transverse walls into asymmetric and finally into vortex walls in simple ferromagnetic tracks as the width is increased, can instead close a significant portion of its flux with the oppositely directed demagnetising field in the other layer of the SyF (see Supplementary Information).

### Current-driven dynamics of coupled walls in SyFs

The current-driven dynamics of a DW may be described using a simple 1-D model34 that describes the DW in terms of a position co-ordinate Z and a canting angle ϕ that acts as a conjugate momentum to Z. This may be readily extended to a pair of such walls (with co-ordinates {Z1, ϕ1} and {Z2, ϕ2} [see Fig. 3a]), that are coupled together by isotropic antiferromagnetic exchange and anisotropic magnetostatic interactions27. Whilst such models have been used in the past to describe vortex and transverse walls in single wires, a 1-D model of a 2-D wall neglects important degrees of freedom35, 36. The simple, rigid walls in our SyFs means that the 1-D model is expected to give more accurate insights into the DW dynamics, although the purpose of using this analytical model is to achieve insight into the depinning mechanism, rather than to provide an exact quantitative description of the system for which numerical micromagnetic simulations incorporating full knowledge of the extrinsic defects in the sample are needed.

We employed 1-D simulations of DW dynamics to gain these insights into the threshold current density in our in-plane magnetised SyF device (the equations of motion of this system are described in the Supplementary Information). It is typical of common ferromagnetic metals that β/α > 1 (refs 37 and 38), where β is the nonadiabatic spin torque coefficient39 and α is the Gilbert damping constant, and so we assume that the dynamics is in the nonadiabatic regime (see Fig. 3a). The estimated exchange coupling and the magnetostatic couplings (see Methods section) indicate also a highly anisotropic total interlayer coupling which is ferromagnetic in the out-of-plane direction and much stronger than the antiferromagnetic in-plane coupling.

Figure 3b shows DW velocity as a function of interlayer coupling and driving current calculated using the 1-D model in the nonadiabatic regime (see Methods section). The anisotropic coupling between the walls, arising from a combination of interlayer exchange and magnetostatics, is parameterised by in-plane Δ|| and out-of-plane $Δ ⊥$ coupling constants. The threshold current, the minimum current needed to depin the walls from the pinning potential and set them moving, is indicated with the red dashed line. The threshold current decreases with increasing interlayer coupling and eventually disappears completely at a strong coupling of Δ|| ≈ −1.9 mJ/m2. This can be qualitatively understood from the presence of a nonadiabatic torque which forces the spins out-of-plane34, 40, a phenomenon caused by spin relaxation39, 41 (see Fig. 3a and the Supplementary Information). This leads to a decrease in interlayer coupling energy at the center of the wall due to strong ferromagnetic out-of-plane coupling and helps free the walls from the pinning potential.

Alternatively, the reduction of threshold current can be explained using wall momentum. For a strong ferromagnetic out-of-plane coupling, the spins at the center of the walls are close to parallel (see Fig. S3 in the Supplementary Information) and therefore ϕ ≡ $1 2 ( φ 1 + φ 2 )$ is small. Since ϕ is the canonical momentum of the average wall position $Z + ≡ 1 2 ( Z 1 + Z 2 )$, the torque and force induced by the applied current are distributed to the dynamics of Z+ and ϕ. If ϕ is kept small due to the nonadiabatic torque and ferromagnetic interlayer coupling, the torque and force are efficiently transferred to the Z+ mode, i.e., to the displacement of the wall, resulting in a reduction of the threshold current. This reduction mechanism is consistent also with the fact that no significant reduction arises when the out-of-plane coupling is antiferromagnetic27. Our 1-D simulations indicate that the threshold current vanishes when the out-of-plane ferromagnetic interlayer coupling is of the same order as the out-of-plane shape anisotropy, as can be seen from the calculations where we adjusted the ratio of $Δ ⊥ / Δ | |$ that are presented in the Supplementary Information in Fig. S5. We conclude that careful optimisation of shape and interlayer coupling anisotropies, by taking into account the finite wire width and other 2-D effects, can be used to design highly energy-efficient DW devices. Careful choice of the layer thicknesses, explored using 1-D model simulations in the Supplementary Information, can also be used to engineer desirable interlayer coupling properties.

The interlayer coupling also affects the Walker breakdown mechanism. The regime after the Walker breakdown is visible in the central part of Fig. 3b as a triangular region, where the dependence on the driving current is nonlinear.

To experimentally investigate this predicted reduction in depinning current density, electrical contacts were patterned on top of the nanowire and elliptical pad of a SyF device with a 400 nm wide track and Co90Fe10 layers that have thicknesses t1 = 13.3 nm and t2 = 6.6 nm. The procedure used for measuring the current-driven mobility curve v(ve) of the 180° coupled DW pair is outlined in Fig. 4a. Here, v is the DW velocity and ve is the electron spin drift velocity, which is proportional to the current density (see Methods). First the coupled 180° DW pair is injected into the neck of the wire by applying a series of fields and current pulses as outlined in the Supplementary Information. This prepares a state similar to that shown in Fig. 1d that is stable in zero field. A single current pulse of selected amplitude and duration is then applied, with electron flow away from the elliptical pad. The field, applied along the wire axis, is then swept up to saturation and the magnetoresistance curve measured. For a given current density, if the pulse duration is too short to fully remove the 180° DW from the track, the magnetoresistance shows a trough in the measured curve, a signature that the wall is still present (see Supplementary Information). An example of this for a 200 ns long pulse of 1.2 × 1011 Am−2 current density is shown in Fig. 4a. On the other hand, if the current pulse is long enough to fully drive the DW out of the track, the magnetoresistance signature does not show the characteristic trough, but decreases monotonically as the thinner Co90Fe10 layer is gradually rotated by the increasing magnetic field. An example of this behaviour, shown in Fig. 4a is for a 2000 ns long pulse of 1.2 × 1011 Am−2 current density.

For each current density value and pulse duration t, these measurements were repeated five times and the average minimum pulse length required to fully switch the magnetisation in the track was used to obtain the average current-driven DW speed v = l/t using the known track length of l = 16 μm. The measured mobility curve v(ve) is shown in Fig. 4b. Below a threshold of ve ~ 1.5 m/s the DWs do not move. A linear behaviour is observed above this threshold, for which a straight line fit returns a slope of 11.6 ± 0.3. This linear behaviour, along with the order of magnitude of the velocities, excludes the creep regime42 and confirms that all our data are measured in the viscous flow regime for domain wall motion43. The spin drift velocity ve is the fastest possible DW velocity in the adiabatic limit, but v > ve has been previously observed in single layer wires by Hayashi et al.44, for instance. This can be explained by the action of the nonadiabatic contribution to the spin transfer torque39, leading to the expression v = (β/α)ve in the regime below Walker breakdown. This relation was also verified for the SAF and SyF structures using micromagnetic simulations and found to hold.

There is extensive data on both β and α for Permalloy thin films, but much less is known about the CoFe alloy that we have used here. Whilst these quantities are likely to have similar orders of magnitude in these two transition metal magnets, it is unlikely that the values will be exactly the same. Vector-network-analyser ferromagnetic resonance measurements, described in more detail in the Supplementary Information, determined α = 0.007 ± 0.001 in our material, slightly less than that usually measured for Permalloy thin films37, 45, 46, but consistent with other measurements of CoFe alloys47, 48.

Combining this with the slope of the v(ve) line implies that β = 0.08 ± 0.01 in our CoFe layers. Again, this is very similar to ref. 49 or just higher than15, 19 typical values for Permalloy, justifying our assumption that nonadiabatic effects are important in this case. Values of β in excess of 0.1 have been measured for vortex cores in Permalloy50,51,52, where the very high magnetisation gradients around the core can lead to enhanced local values for β53. The fact that our simple Néel DWs are narrower than typical transverse DWs in soft magnetic nanowires can therefore be expected to lead to a mild enhancement of β. Combined with the reduced value for α, these two effects lead to a raised value for the β/α ratio.

It is noteworthy that the zero-field critical current density for the onset of motion of this 180° coupled DW pair is just smaller than 1.0 × 1011 Am−2, a remarkably low value compared to the typical values observed in single-layer Permalloy magnetic nanowires, which are in the 1012 Am−2 range11, 14, 15, 20. It is even lower then the 2.5 × 1011 A/m2 threshold current density achieved in an optimised Co/Ni perpendicularly magnetised stack. It represents a roughly fivefold reduction over the critical current density in perpendicularly magnetised SAF nanowires26, in which the DWs are driven by highly efficient spin Hall torques and giant exchange torques. In these in-plane SyFs, only the comparatively inefficient volume spin transfer torques, with an unremarkable value of the nonadiabaticity constant β are able to depin the coupled DW pairs at this low value of current density, which has to be compared with a depinning field Hdepin ~ 150 Oe, taken from the magnetoresistance curves. At these low current densities around critical value, temperature rises due to Joule heating are limited to a few kelvins, meaning that thermal effects such as the nucleation of additional domain walls, can be safely ruled out.

Control measurements have been carried out on ferromagnetically coupled wires identical in every respect but for slightly thicker (1 nm) Ru spacer layers, changing the sign of the coupling. These wires have a similar anisotropic magnetoresistance response to their AF-coupled counterparts, allowing them to be tested for current-driven domain wall motion by the same method. As shown in Fig. 4b, no domain wall motion was observed at zero field, in contrast to the antiferromagnetically coupled wires, before irreversible changes to the resistance occur for current densities exceeding about 8 × 1011 A/m2, directly showing the effect of AF coupling in a wall pair in reducing the critical current.

The threshold current density has been shown to vary with pulse duration54, 55, rising when pulses are very short. Our experiments use long pulses of a few hundred or thousand ns, but the pulse length dependence experiments in these previous reports show that our results are comparable with any others that use pulses that are longer than a few ns.

The DWs display a 2-D structure in microscope imaging. Notches and impurities that pin the walls are also 2-D objects. Therefore the dynamics of the walls are quantitatively affected by 2-D effects which are not captured by the 1-D model. However, in the 1-D simulations the calculated in-plane coupling at the point where the threshold current is removed completely is Δ|| = −1.9 mJ/m2. This is of the same order as the estimated total interlayer coupling in experiments (see Methods) and gives evidence that the large reduction in the DW threshold current is due to nonadiabatic driving in the presence of highly anisotropic interlayer coupling. The fact that the experimental depinning current density is slightly below that predicted by the model is due to the fact that the wall is not in reality a completely rigid object, as can be seen from Fig. 2c for instance, which allows it to be slightly more easily depinned. Simulations using the 1D model (described in the Supplementary information) show that the reduction in critical current density is expected to be even larger in a properly balanced SAF.

## Discussion

Here we have shown that the magnetostatics in in-plane magnetised SyF nanowires lead to coupled pairs of simple Néel walls that are narrow, rigid and unaffected by the wire width in which they are present. The mixture of exchange and magnetostatic coupling between the walls in the pair leads to an anisotropic coupling overall, which even has different signs in the in-plane and out-of-plane directions. This anisotropic coupling, when combined with non-adiabatic driving, leads to very effective depinning from an extrinsic pinning potential by exploiting the internal degrees of freedom within the coupled wall pair that do not exist in a single wall. We realised this experimentally at the very low current density of 1011 Am−2, roughly one order of magnitude lower with respect to typical single layer ferromagnetic wires, and at least an eightfold reduction when compared to a control sample that was identical in every way but for being ferromagenetically coupled through a slightly thicker Ru spacer. Since power dissipation goes quadratically with current, significant reductions in power consumption can be achieved by properly exploiting this phenomenon.

Although we studied the nature of these internal degrees of freedom and how they may be exploited in the setting of in-plane magnetised materials with the domain walls driven by volume spin-transfer torques, these ideas are not limited to that context. The important feature of the non-adiabatic component of the volume spin-transfer torque is that it has a field-like symmetry. Such field-like components are also present in interfacial spin-orbit torques56, which tend to be very efficient. We can therefore expect that our results can be used to design appropriately configured coupled DW pairs in spin-orbit torque-driven systems in order to realise a similar reduction in the current density needed for depinning. Thus, these systems show great promise for future devices based on current-driven DW motion that are very energy efficient.

## Methods

### Sample Fabrication and Measurement

Thin films of substrate/Ru (2)/Co90Fe10 (10)/Ru (0.7)/Co90Fe10 (10)/Ru (2) – SAF, thickness values in nm – and susbstrate/Ru (2)/Co90Fe10 (6.6)/Ru (0.7)/Co90Fe10 (13.3)/Ru (2) - SyF - were sputtered using ultrapure Ar gas on thermally oxidized Si substrates for XMCD-PEEM imaging, thin-film characterisation, and electrical measurements, and on Si3N4 membranes for LTEM imaging. The layer closest to the sample surface is the top layer with thickness t1, whilst the bottom layer closest to the substrate has thickness t2. Samples were patterned by electron-beam lithography and an Al/Ti hard-mask was sputtered and obtained by lift-off. The wire width was 400 nm for PEEM and magnetotransport measurements, and 800 nm for LTEM. Ar-ion milling was used to remove the thin film not covered by the Al/Ti hard-mask and the final patterns were obtained by etching the Al layer using MF319, removing the Al/Ti hard-mask. Electrical contacts were obtained by optical lithography and sputtering of Ru (5 nm)/Au (80 nm). Magnetoresistance measurements were carried out at room temperature using a lock-in amplifier method at 10 kHz, with 1 μA amplitude source current. The rise/fall time of the current pulses used to measure the wall velocity was ~5 ns.

The magnetic and structural properties of the unpatterned samples were investigated using VSM, x-ray diffraction and TEM imaging using 5 mm × 5 mm thin-films sputtered on thermally oxidized Si substrates. The saturation magnetisation Ms of the Co90Fe10 layers was measured to be 1.40 MA/m. The measured saturation field implies a bilinear interlayer indirect exchange coupling constant

$J 1 =− μ 0 M S 2 ( 2 t 1 t 2 t 1 + t 2 ) H S =− 1.0 m J / m 2 ,$

where Hs is the saturation field of the SyF structure. The spin-polarisation, P, of the Co90Fe10 layers, was 0.34 ± 0.02 as determined from spin-wave Doppler measurements on a Ru/Co90Fe10/Ru trilayer in the magnetostatic surface wave geometry57, 58. The current density, J, used in the experiments was converted to spin drift velocity, ve, as ve = PgμBJ/2eMs.

### Magnetic Imaging

XMCD-PEEM imaging was carried out at the I06 beamline of the Diamond Light Source synchrotron, using circularly-polarised photons tuned the Co L3 edge at 779 eV. The samples were mounted on a PEEM cartidge containing a small electromagnet with maximum field at the sample of ±250 Oe. All images were obtained at remanence. The x-ray beam is directed along the track and the magnetisation projection along the beam direction is shown as a gray-scale. The escape depth of the photelectrons is only a few nm and thus only the top Co90Fe10 layer contributes any significant magnetic contrast.

The Lorentz imaging experiments described here were performed on a Tecnai T20 TEM. In this mode the objective lens of the microscope is weakly excited to provide a field perpendicular to the thin film sample and a magnetising sequence is then carried out by tilting the sample in this field59. Magnetic contrast is generated by defocussing the image forming lens which reveals DWs as bright and dark lines on a uniform background. Furthermore in the case of magnetic nanowires similar contrast can be observed along the wire edges where the magnetisation has a component parallel to the edge. The magnetisation reversal of the structure was carried out in Lorentz TEM mode with a weak excitation of the objective lens set to a value of 1100 Oe and the sample then tilted so that an in-plane field along the wire axis of 650 Oe was applied, which is enough the saturate both layers in the field direction, as is shown in the starting state in Fig. 2a.

### 1-D Model of Domain Wall Dynamics

The 1-D model of SAFs has been developed in ref. 27 and involves a system of Néel-type DWs in a synthetic antiferromagnet where magnetisation is in the plane of the wire. The walls are described using two parameters for each wall; the positions of the walls along the wire Z i , i = 1, 2 and the angles of the spins with respect to the wire plane at the center of the wall ϕ i , i = 1, 2 (see Fig. 3a). The model incorporates interlayer coupling terms due to magnetostatic effects and the indirect exchange interaction between the layers. The total coupling is ferromagnetic for the out-of-plane component $Δ ⊥$ and antiferromagnetic for the in-plane coupling Δ||. In view of the coupling parameters obtained from micromagnetic simulations we use a ratio $Δ ⊥ / Δ | | =−4$ in the 1-D simulations, i.e. a significantly stronger out-of-plane coupling. For fuller details of the 1-D model and the equations of motion, see the Supplementary Information.

We assumed a Co-like value for the exchange stiffness A = 30 pJ/m. Demagnetising factors for the layers were calculated using the formulae given by Aharoni60, leading to the following shape anisotropy parameters: K x,1 = 63.9 kJ/m3, K y,1 = 1.17 MJ/m3, K x,2 = 36.2 kJ/m3, K y,2 = 1.20 MJ/m3. This leads to wall width parameters $Λ i = A / K x , i$, i.e. neglecting any effects of coupling, of Λ1 = 22 nm and Λ2 = 29 nm. Note that this wall width parameter is not necessarily the same as the apparent DW width in e.g. an LTEM image. We used a Gilbert damping parameter α = 0.007 (measured by ferromagnetic resonance as described in the Supplementary Information) and nonadiabatic torque constant β = 0.08 (measured from the slope of the v(ve) curve in Fig. 4b). The pinning potential is of the extrinsic type and is modelled with a parabolic potential well in one of the layers with a strength equivalent to a 150 Oe field, equivalent to the depinning field observed in experiments. The initial conditions for the walls correspond to the ground state with both walls at a value of Z equal to that at the center of the pinning potential.

### Micromagnetic Modelling

Micromagnetic simulations were performed using the BORIS micromagnetics software developed by us. The simulations were ran using the finite difference method and the LLG and LLG-STT equations were solved explicitly using the 2nd order Adams-Bashforth-Moulton method with adaptive time-step. Exchange fields were calculated using the 6-neighbour stencil with Neumann boundary conditions and magnetostatic fields were calculated using FFT-based convolution with zero padding. The mesh cell size was 5 nm. The in-plane and out-of-plane coupling parameters were calculated respectively by obtaining the difference between the total energy density values, including magnetostatic, direct exchange and bilinear surface exchange interactions, for anti-parallel and parallel Néel DW rotations in the two layers respectively. For the in-plane coupling Δ|| the Néel wall rotation occurs in the plane, whilst for the out-of-plane coupling $Δ ⊥$ the Néel wall rotation occurs perpendicular to the plane. When combined with the isotropic bilinear indirect exchange coupling J1 = −1.0 mJ/m2, we obtained overall couplings of Δ|| = −0.75 mJ/m2 and $Δ ⊥ =+3.02$ mJ/m2.

### Data availability

The datasets generated during and/or analysed during the current study are publicly available in the University of Leeds Research Data Repository, https://doi.org/10.5518/175.

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

## References

1. 1.

Grünberg, P., Schreiber, R., Pang, Y., Brodsky, M. B. & Sowers, H. Layered magnetic structures: Evidence for antiferromagnetic coupling of Fe layers across Cr interlayers. Phys. Rev. Lett. 57, 2442–2445, doi:10.1103/PhysRevLett.57.2442 (1986).

2. 2.

Parkin, S., More, N. & Roche, K. Oscillations in exchange coupling and magnetoresistance in metallic superlattice structures: Co/Ru, Co/Cr and Fe/Cr. Phys. Rev. Lett. 64, 2304–2307, doi:10.1103/PhysRevLett.64.2304 (1990).

3. 3.

Steadman, P. et al. Exchange bias in spin-engineered double superlattices. Phys. Rev. Lett. 89, 077201, doi:10.1103/PhysRevLett.89.077201 (2002).

4. 4.

Pinarbasi, M. et al. 12 Gb/in2 recording demonstration with SV read heads and conventional narrow pole-tip write heads. IEEE Trans. Magn. 35, 689–694, doi:10.1109/20.750629 (1999).

5. 5.

Slaughter, J. et al. High speed toggle MRAM with MgO-based tunnel junctions. In Electron Devices Meeting, 2005. IEDM Technical Digest. IEEE International. 873 (2005).

6. 6.

Boulle, O., Malinowski, G. & Kläui, M. Current-induced domain wall motion in nanoscale ferromagnetic elements. Materials Science & Engineering R 72, 159 (2011).

7. 7.

Parkin, S. & Yang, S.-H. Memory on the racetrack. Nature Nano 10, 195–198, doi:10.1038/nnano.2015.41 (2015).

8. 8.

Allwood, D. A. et al. Magnetic domain-wall logic. Science 309, 1688–92, doi:10.1126/science.1108813 (2005).

9. 9.

Xu, P. et al. An all-metallic logic gate based on current-driven domain wall motion. Nature Nano 3, 97–100, doi:10.1038/nnano.2008.1 (2008).

10. 10.

Diegel, M., Glathe, S., Mattheis, R., Scherzinger, M. & Halder, E. A new four bit magnetic domain wall based multiturn counter. IEEE Trans. Magn. 45, 3792–3795, doi:10.1109/TMAG.2009.2024426 (2009).

11. 11.

Yamaguchi, A. et al. Real-space observation of current-driven domain wall motion in submicron magnetic wires. Phys. Rev. Lett. 92, 077205, doi:10.1103/PhysRevLett.92.077205 (2004).

12. 12.

Beach, G., Knutson, C., Nistor, C., Tsoi, M. & Erskine, J. Nonlinear domain-wall velocity enhancement by spin-polarized electric current. Phys. Rev. Lett. 97, 057203, doi:10.1103/PhysRevLett.97.057203 (2006).

13. 13.

Hayashi, M., Thomas, L., Rettner, C., Moryia, R. & Parkin, S. Direct observation of the coherent precession of magnetic domain walls propagating along permalloy nanowires. Nature Phys 3, 21–25, doi:10.1038/nphys464 (2007).

14. 14.

Meier, G. et al. Direct imaging of stochastic domain-wall motion driven by nanosecond current pulses. Phys. Rev. Lett. 98, 187202, doi:10.1103/PhysRevLett.98.187202 (2007).

15. 15.

Lepadatu, S., Vanhaverbeke, A., Atkinson, D., Allenspach, R. & Marrows, C. H. Dependence of domain-wall depinning threshold current on pinning profile. Phys. Rev. Lett. 102, 127203, doi:10.1103/PhysRevLett.102.127203 (2009).

16. 16.

McMichael, R. D. & Donahue, M. J. Head to head domain wall structures in thin magnetic strips. IEEE Trans. Magn. 33, 4167–4169, doi:10.1109/20.619698 (1997).

17. 17.

Nakatani, Y., Thiaville, A. & Miltat, J. Head-to-head domain walls in soft nano-strips: a refined phase diagram. J. Magn. Magn. Mater. 290–291, 750–753, doi:10.1016/j.jmmm.2004.11.355 (2005).

18. 18.

Locatelli, N., Cros, V. & Grollier, J. Spin-torque building blocks. Nature Mater 13, 11–20, doi:10.1038/nmat3823 (2014).

19. 19.

Lepadatu, S. et al. Experimental determination of spin-transfer torque nonadiabaticity parameter and spin polarization in permalloy. Phys. Rev. B 79, 094402, doi:10.1103/PhysRevB.79.094402 (2009).

20. 20.

Heyne, L. et al. Geometry-dependent scaling of critical current densities for current-induced domain wall motion and transformations. Phys. Rev. B 80, 184405, doi:10.1103/PhysRevB.80.184405 (2009).

21. 21.

Kläui, M. et al. Direct observation of domain-wall configurations transformed by spin currents. Phys. Rev. Lett. 95, 026601, doi:10.1103/PhysRevLett.95.026601 (2005).

22. 22.

Parkin, S. S. P., Hayashi, M. & Thomas, L. Magnetic domain-wall racetrack memory. Science 320, 190–194, doi:10.1126/science.1145799 (2008).

23. 23.

Thiaville, A., Rohart, S., Jué, E., Cros, V. & Fert, A. Dynamics of Dzyaloshinskii domain walls in ultrathin magnetic films. Europhys. Lett. 100, 57002, doi:10.1209/0295-5075/100/57002 (2012).

24. 24.

Emori, S., Bauer, U., Ahn, S.-M., Martinez, E. & Beach, G. S. D. Current-driven dynamics of chiral ferromagnetic domain walls. Nature Mat 12, 611–616, doi:10.1038/nmat3675 (2013).

25. 25.

Ryu, K.-S., Thomas, L., Yang, S.-H. & Parkin, S. S. P. Chiral spin torque at magnetic domain walls. Nature Nano 8, 527–533, doi:10.1038/nnano.2013.102 (2013).

26. 26.

Yang, S. H., Ryu, K. S. & Parkin, S. S. P. Domain-wall velocities of up to 750 ms−1 driven by exchange-coupling torque in synthetic antiferromagnets. Nature Nanotech 10, 221226 (2015).

27. 27.

Saarikoski, H., Kohno, H., Marrows, C. H. & Tatara, G. Current-driven dynamics of coupled domain walls in a synthetic antiferromagnet. Phys. Rev. B 90, 094411, doi:10.1103/PhysRevB.90.094411 (2014).

28. 28.

Koyama, T. et al. Observation of the intrinsic pinning of a magnetic domain wall in a ferromagnetic nanowire. Nature Mater 10, 194–197, doi:10.1038/nmat2961 (2011).

29. 29.

Fruchart, O. & Diény, B. Magnetostatics of synthetic ferrimagnet elements. J. Magn. Magn. Mater. 324, 365–368, doi:10.1016/j.jmmm.2011.07.020 (2012).

30. 30.

Schrefl, T., Fidler, J., Kirk, K. & Chapman, J. Domain structures and switching mechanisms in patterned magnetic elements. J. Magn. Magn. Mater. 175, 193–204 (1997).

31. 31.

Benitez, M. J. et al. Magnetic microscopy and topological stability of homochiral Néel domain walls in a Pt/Co/AlO x trilayer. Nature. Comm 6, 8957, doi:10.1038/ncomms9957 (2015).

32. 32.

Hellwig, O., Berger, A. & Fullerton, E. Domain walls in antiferromagnetically coupled multilayer films. Phys. Rev. Lett. 91, 197203, doi:10.1103/PhysRevLett.91.197203 (2003).

33. 33.

Benitez, M. J. et al. Engineering magnetic domain-wall structure in permalloy nanowires. Phys. Rev. Applied 3, 034008, doi:10.1103/PhysRevApplied.3.034008 (2015).

34. 34.

Tatara, G. & Kohno, H. Theory of current-driven domain wall motion: Spin transfer versus momentum transfer. Phys. Rev. Lett. 92, 086601, doi:10.1103/PhysRevLett.92.086601 (2004).

35. 35.

Beach, G. S. D., Tsoi, M. & Erskine, J. L. Current-induced domain wall motion. J. Magn. Magn. Mater. 320, 1272–1281, doi:10.1016/j.jmmm.2007.12.021 (2008).

36. 36.

Yoshimura, Y. et al. Soliton-like magnetic domain wall motion induced by the interfacial Dzyaloshinskii-Moriya interaction. Nature Phys 12, 157161–161, doi:10.1038/nphys3535 (2015).

37. 37.

Lepadatu, S. et al. Domain-wall pinning, nonadiabatic spin-transfer torque, and spin-current polarization in permalloy wires doped with vanadium. Phys. Rev. B 81, 020413, doi:10.1103/PhysRevB.81.020413 (2010).

38. 38.

Sekiguchi, K. et al. Time-domain measurement of current-induced spin wave dynamics. Phys. Rev. Lett. 108, 017203, doi:10.1103/PhysRevLett.108.017203 (2012).

39. 39.

Thiaville, A., Nakatani, Y., Miltat, J. & Suzuki, Y. Micromagnetic understanding of current-driven domain wall motion in patterned nanowires. Europhys. Lett. 69, 990–996, doi:10.1209/epl/i2004-10452-6 (2005).

40. 40.

Tatara, G., Kohno, H. & Shibata, J. Microscopic approach to current-driven domain wall dynamics. Phys. Rep 468, 213–301, doi:10.1016/j.physrep.2008.07.003 (2008).

41. 41.

Zhang, S. & Li, Z. Roles of nonequilibrium conduction electrons on the magnetization dynamics of ferromagnets. Phys. Rev. Lett. 93, 127204, doi:10.1103/PhysRevLett.93.127204 (2004).

42. 42.

DuttaGupta, S. et al. Adiabatic spin-transfer-torque-induced domain wall creep in a magnetic metal. Nature Phys 12, 333–336, doi:10.1038/nphys3593 (2016).

43. 43.

Metaxas, P. J. et al. Creep and flow regimes of magnetic domain-wall motion in ultrathin Pt/Co/Pt films with perpendicular anisotropy. Phys. Rev. Lett. 99, 217208, doi:10.1103/PhysRevLett.99.217208 (2007).

44. 44.

Hayashi, M. et al. Current driven domain wall velocities exceeding the spin angular momentum transfer rate in permalloy nanowires. Phys. Rev. Lett. 98, 037204, doi:10.1103/PhysRevLett.98.037204 (2007).

45. 45.

Walowski, J. et al. Energy equilibration processes of electrons, magnons, and phonons at the femtosecond time scale. Phys. Rev. Lett. 101, 237401, doi:10.1103/PhysRevLett.101.237401 (2008).

46. 46.

Weindler, T. et al. Magnetic damping: Domain wall dynamics versus local ferromagnetic resonance. Phys. Rev. Lett. 113, 237204, doi:10.1103/PhysRevLett.113.237204 (2014).

47. 47.

Rantschler, J., Ding, Y., Byeon, S.-C. & Alexander, C. Jr. Microstructure and damping in FeTiN and CoFe films. J. Appl. Phys. 93, 6671–6673, doi:10.1063/1.1556099 (2003).

48. 48.

Schoen, M. A. W. et al. Ultra-low magnetic damping of a metallic ferromagnet. Nature Physics 12, 839–842, doi:10.1038/nphys3770 (2016).

49. 49.

Eltschka, M. et al. Nonadiabatic spin torque investigated using thermally activated magnetic domain wall dynamics. Phys. Rev. Lett. 105, 056601, doi:10.1103/PhysRevLett.105.056601 (2010).

50. 50.

Heyne, L. et al. Direct determination of large spin-torque nonadiabaticity in vortex core dynamics. Phys. Rev. Lett. 105, 187203, doi:10.1103/PhysRevLett.105.187203 (2010).

51. 51.

Pollard, S. D. et al. Direct dynamic imaging of non-adiabatic spin torque effects. Nature Comm 3, 1028, doi:10.1038/ncomms2025 (2012).

52. 52.

Rößler, S. et al. Nonadiabatic spin-transfer torque of magnetic vortex structures in a permalloy square. Phys. Rev. B 89, 174426, doi:10.1103/PhysRevB.89.174426 (2014).

53. 53.

Claudio-Gonzalez, D., Thiaville, A. & Miltat, J. Domain wall dynamics under non-local spin-transfer torque. Phys. Rev. Lett. 108, 227208, doi:10.1103/PhysRevLett.108.227208 (2012).

54. 54.

Fukami, S., Yamanouchi, M., Ikeda, S. & Ohno, H. Depinning probability of a magnetic domain wall in nanowires by spin-polarized currents. Nature Commun 4, 2293, doi:10.1038/ncomms3293 (2013).

55. 55.

Parkin, S., Thomas, L. & Yang, S. Domain wall motion in perpendicularly magnetized wires having magnetic multilayers with engineered interfaces US Patent 8,638,601 (2014).

56. 56.

Garello, K. et al. Symmetry and magnitude of spin-orbit torques in ferromagnetic heterostructures. Nature Nano 8, 587–93, doi:10.1038/nnano.2013.145 (2013).

57. 57.

Zhu, M., Dennis, C. L. & McMichael, R. D. Temperature dependence of magnetization drift velocity and current polarization in Ni80Fe20 by spin-wave doppler measurements. Phys. Rev. B 81, 140407, doi:10.1103/PhysRevB.81.140407 (2010).

58. 58.

Sugimoto, S., Rosamond, M., Linfield, E. H. & Marrows, C. H. Observation of spin-wave Doppler shift in Co90Fe10/Ru micro-strips for evaluating spin polarization. Appl. Phys. Lett. 109, 112405, doi:10.1063/1.4962835 (2016).

59. 59.

McVitie, S. et al. Aberration corrected Lorentz scanning transmission electron microscopy. Ultramicroscopy 152, 57–62, doi:10.1016/j.ultramic.2015.01.003 (2015).

60. 60.

Aharoni, A. Demagnetizing factors for rectangular ferromagnetic prisms. J. Appl. Phys. 83, 3432–3434, doi:10.1063/1.367113 (1997).

## Acknowledgements

This work was partly supported by the EPSRC through grants EP/I011668/1 and EP/I011668/1, the Marie Curie International Incoming Fellowship SKYHIGH, and by a Grant-in-Aid for Scientific Research (C) No. 26390014 from Japan Society for the Promotion of Science. We thank Diamond Light Source for the provision of beamtime under proposal number SI-6709.

## Author information

### Affiliations

1. #### School of Physics & Astronomy, University of Leeds, Leeds, LS2 9JT, United Kingdom

• , Thomas A. Moore
• , Gavin Burnell
• , Satoshi Sugimoto
• , Daniel Yesudas
• , May C. Wheeler
•  & Christopher H. Marrows

3. #### RIKEN Center for Emergent Matter Science (CEMS), 2-1 Hirosawa, Wako, Saitama, 351-0198, Japan

• Henri Saarikoski
•  & Gen Tatara
4. #### Scottish Universities Physics Alliance, School of Physics & Astronomy, University of Glasgow, Glasgow, G12 8QQ, United Kingdom

• Robert Beacham
• , Maria Jose Benitez
• , Damien McGrouther
•  & Stephen McVitie
5. #### Departamento de Física, Escuela Politécnica Nacional, Quito, Ecuador

• Maria Jose Benitez
6. #### Diamond Light Source, Chilton, Didcot, OX11 0DE, United Kingdom

• Jorge Miguel
•  & Sarnjeet S. Dhesi

### Contributions

S.L., T.A.M., G.B., D.M., S.M., and C.H.M. planned the experiments. H.S., G.T., and C.H.M. planned the theoretical calculations, which were undertaken by H.S., S.L. fabricated the samples and performed magnetotransport measurements. D.Y. grew the samples for and performed the FMR measurements with the assistance of M.C.W., S.S. prepared the samples for and performed the spin-wave Doppler measurements. R.B. fabricated the Lorentz TEM specimens and performed the imaging and image analysis. M.J.B. fabricated the TEM cross-section specimens and performed the imaging and image analysis. S.L., R.B., M.J.B., T.A.M., G.B., D.M., S.M., J.M., and S.S.D. performed the PEEM imaging, S.L. performed the image analysis. S.L. developed the bespoke micromagnetics code boris and performed the micromagnetic modelling. S.L., H.S., and C.H.M. wrote the paper. All authors discussed the data and reviewed the manuscript.

### Competing Interests

The authors declare that they have no competing interests.

### Corresponding author

Correspondence to Christopher H. Marrows.