Abstract
We demonstrate the suppression of photon shot noise dephasing in a superconducting qubit by eliminating its dispersive coupling to the readout cavity. This is achieved in a tunable coupling qubit, where the qubit frequency and coupling rate can be controlled independently. We observe that the coherence time approaches twice the relaxation time and becomes less sensitive to thermal photon noise when the dispersive coupling rate is tuned from several MHz to 22 kHz. This work provides a promising building block in circuit quantum electrodynamics that can hold high coherence and be integrated into larger systems.
Introduction
Superconducting quantum circuits are a strong candidate for quantum computing,^{1,2,3} and a convenient platform for quantum optics^{4,5,6} and quantum simulation.^{7,8} Extensive efforts have been made in the last decade to isolate these quantum systems from various decay channels and noise sources in the environment, leading to an increase of several orders of magnitude in energy relaxation time T _{1} and phase coherence time T _{2}.^{9} Stateoftheart devices have achieved T _{1} and T _{2} in the millisecond regime^{10,11} and pushed gate fidelity close to the threshold for faulttolerant quantum computing.^{12} However, the progress in T _{2} is slower than that in T _{1} and T _{2}/T _{1} ratios in these devices fall in the range between 0.5 and 1.5.^{10,13,14} Deviation from the theoretical limit of T _{2} = 2T _{1} indicates dephasing mechanisms that need to be understood and circumvented.
In circuit quantum electrodynamics (cQED),^{15,16} manipulation and readout of a superconducting qubit are mediated by its coupling to a transmission line cavity. When the coupling is dispersive, photons in the cavity can be utilized to measure the qubit if their phase is shifted by a distinguishable amount depending on the qubit state. On the other hand, changes in cavity photon number will shift the qubit frequency due to the same coupling mechanism. When the amount of the frequency shift is large enough, thermal or quantum fluctuations of cavity photons lead to dephasing of the qubit. This photon shot noise dephasing mechanism has been studied theoretically^{17} and experimentally^{14} and has become a dominant factor that limits the coherence time of superconducting qubits. The qualitative discussion above indicates that the dephasing can be suppressed by reducing (1) the photon number fluctuation, characterized by cavity decay rate κ, (2) the thermal photon population n _{th}, and (3) the frequency shift caused by each photon, characterized by the dispersive coupling rate χ. Most work in the past has adopted the first two strategies and used highQ (>10^{6}) 3D cavities^{10,18} and careful filtering and thermal anchoring to reduce κ and n _{th}.^{14,19} Here, we focus on the third approach and demonstrate the suppression of photon shot noise dephasing when χ is tuned to near zero. This is realized in a tunable coupling qubit (TCQ),^{20,21} where the qubit frequency and coupling strength can be tuned independently.^{22} Moreover, we show that measurement of the qubit state can still be performed conveniently when χ ≪ κ.
In this paper, we start with spectroscopic measurements on the TCQ to demonstrate the independent tunability of its frequency and dispersive coupling rate. We achieve χ as low as 22 kHz when the dispersive interaction of two different qubit modes is tuned to cancel each other. Next we show that readout of the qubit state near the zeroχ regime can be realized by utilizing a higher energy level. Finally, we perform time domain measurements of T _{1} and T _{2} with injected noise and demonstrate the robustness of T _{2} against photon shot noise when χ is near zero.
Results
The TCQ, shown in Fig. 1a, consists of two transmon qubits^{23} strongly coupled to each other via a common third island. The geometry of the islands are designed to minimize the electric participation ratios in the material interfaces and reduce bulk and surface losses of the qubit.^{24} The two transmons are formed by capacitively shunted SQUID loops and their frequencies can be tuned by two DC voltages applied to the local magnetic flux bias lines. The strong coupling between the transmon states causes their hybridization and results in a Vshaped energy diagram shown in Fig. 1b. The oneexcitation manifold contains two collective qubit states whose frequencies ω _{±} and dipole coupling rates g _{±} can be tuned as a function of the two flux biases. Tunable coupling originates from the interference between the dipole moments of the two transmons and provides an extra degree of freedom compared to standard transmon qubits. The twoexcitation states acquire different selfanharmonicities and crossanharmonicities α _{±} and α _{ c } due to the hybridization, which allows us to drive a desired transition between two states (indicated by arrows in Fig. 1b) without causing other unwanted transitions. A coplanar waveguide (CPW) cavity with resonance frequency ω _{ r }/2π = 7.14 GHz and linewidth κ/2π = 250 kHz is capacitively coupled to the TCQ to drive and read out the qubit states.
We operate the TCQ in the dispersive regime, where the qubitcavity detunings Δ_{±} = ω _{±} − ω _{ r } ≫ g _{±}, and the Hamiltonian of the device can be approximated by
Here, a, b _{±} denote the annihilation operators for the cavity and qubit modes, and χ _{±} are the dispersive coupling rates between the qubits and the cavity. The measured values for the parameters are ω _{−}/2π = 7.25 GHz, 0≲g _{−}/2π < 10 MHz, ω _{+}/2π ≈ 9.80 GHz, g _{+}/2π ≈ 90 MHz, α _{−}/2π = 129 MHz, α _{+}/2π = 239 MHz, and α _{ c }/2π = 358 MHz. In this work, we use the ground (0_{−}0_{+}〉) and first excited (1_{−}0_{+}〉) states as the computational basis, so the logical qubit has frequency ω _{−} and dispersive coupling rate χ _{−}. The tunability of χ _{−} can be seen from its explicit expression derived in Gambetta et al.^{20} using secondorder perturbation theory,
where χ _{1,2} correspond to contributions from the two collective qubit states. The ability to vary g _{±} in addition to Δ_{±} allows us to tune χ _{−} in a flexible way. In particular, when we tune one qubit into the straddling regime^{23,25} and the other far above the cavity, i.e., g _{−} ≪ Δ_{−} < α _{−} and Δ_{+} ≫ max(α _{c}, g _{+}), χ _{1} and χ _{2} have opposite signs and χ _{−} reaches zero when they cancel each other. In the experiment, we fix Δ_{−} and use g _{−} as the main control knob to tune χ _{−}: When g _{−} is large enough, χ _{1} > χ _{2} and χ _{−} is positive; as we tune down g _{−}, χ _{1} decreases and χ _{−} becomes negative when χ _{1} < χ _{2}.
Figure 2 shows the measured data for tuable χ _{−}. Standard qubit spectroscopy measurement is repeated for different combinations of the two flux biases (Φ_{1}, Φ_{2}) to map out the constant ω _{−} contour in Fig. 2a. Here, Φ_{1} is varied linearly and Φ_{2} (not shown in the figure) is determined by the condition that ω _{−}/2π remains 7.25 GHz when the intracavity photon number \(\bar{n}\) is small. Along the contour, the phase shift of the cavity transmission changes sign, indicating that χ _{−} crosses zero. For larger \(\bar{n}\), the qubit frequency is dressed by cavity photons and exhibits an AC Stark shift^{26} of \(\bar{n}{\chi }_{}\). The dressed qubit frequency in Fig. 2b shows clearly that χ _{−} can be tuned to be both positive and negative, from a few MHz down to below the cavity linewidth κ/2π = 250 kHz, which cannot be resolved in the qubit spectroscopy.
As χ _{−} approaches zero, so does the readout contrast because there is no dispersive shift caused by the 1_{−}0_{+}〉 state, as is illustrated in Fig. 2 near Φ_{1} = −0.95. To achieve efficient readout for small χ _{−}, we adopt a scheme that utilizes a third state 1_{−}1_{+}〉. In this scheme, we apply a transfer pulse at frequency ω _{+} − α _{ c } to the TCQ, inducing a 1_{−}0_{+}〉 → 1_{−}1_{+}〉 transition, immediately before the readout pulse at frequency ω _{ r }. The 1_{−}1_{+}〉 state provides a measured dispersive shift of −1.2 MHz around the zero χ _{−} point and can be used to indirectly read out the logical qubit state. To test this readout method, we prepare the logical qubit to a state ψ〉 characterized by Rabi angle θ _{1}, i.e., \(\left\psi\right\rangle =\,\cos ({\theta}_{1}/2)\left0_{}{0}_{+}\right\rangle +\,\sin ({\theta}_{1}/2)\left1_{}{0}_{+}\right\rangle \), by sending a Gaussian pulse at frequency ω _{−}. A transfer pulse with Rabi angle θ _{2} is then applied as described above, followed by the readout pulse. The widths of the Gaussian pulses are fixed at σ = 16 ns and θ _{1,2} are controlled by the pulse amplitudes. Figure 3a shows the measured homodyne signal at χ _{−} ≈ 0 as a function of θ _{1} and θ _{2}. Rabi oscillations for both 0_{−}0_{+}〉 ↔ 1_{−}0_{+}〉 and 1_{−}0_{+}〉 ↔ 1_{−}1_{+}〉 transitions are observed, demonstrating coherent transfers between the quantum states. In the absence of the transfer pulse, no visible contrast is observed because of small χ _{−} (blue dots in Fig. 3b). As the amplitude of the transfer pulse is adjusted to θ _{2} = π, ψ〉 is transferred to \(\left\psi^{\prime}\right\rangle =\,\cos (\theta_{1}/2)\left0_{}{0}_{+}\right\rangle +\,\sin (\theta _{1}/2)\left1_{}{1}_{+}\right\rangle\), which gives the maximum readout contrast (red crosses in Fig. 3b) and recovers the Rabi angle θ _{1}. This method allows for the single qubit control and readout scheme to be performed entirely with microwave pulses, and does not involve dynamical tuning of χ _{−} via fast flux biasing, which increases experimental complexity and might cause unwanted qubit errors. It also allows low pass filtering to reduce the Purcell decay of the qubit through the flux bias lines.^{27,28}
Combining the tunability of χ _{−} and the readout method, we perform time domain measurements for the qubit relaxation and coherence time. In addition to the standard measurement setup, we use a noise source to study the influence of thermal photon fluctuations on qubit dephasing. White noise within the bandwidth 7.1375 GHz ± 5 MHz is injected to the device, covering the cavity but not the qubit, and its power density determines the intracavity noise photon number n _{th}. In Fig. 4a, the measured T _{1} and T _{2} for χ _{−}/2π = 1.9 MHz are plotted as a function of the injected noise power. A Hahn echo pulse is used in measuring T _{2} to eliminate slow dephasing processes caused by flux noise, etc. While T _{1} exhibits little dependence on the injected noise and remains 8–11 μs, T _{2} drops from 16 to 3.5 μs as the noise power increases, reflecting a photon shot noise limited T _{2} when χ _{−} is comparable to χ used in normal transmon devices. Figure 4b shows the result for the same measurements when χ _{−} ≈ 0 and we obtain T _{1} = 10~12 μs and T _{2} = 20~22 μs, and no reduction is observed in either T _{1} or T _{2} up to n _{th} = 0.13. To quantitatively analyze the result, we use the analytic expression for photon shot noise dephasing rate Γ_{ ϕ } derived in Rigetti et al. and Clerk and Utami,^{14,29}
and fit the measured T _{2} data to Eq. 3, shown in the red curves in Fig. 4. In Fig. 4a, a single linear fitting parameter converts the output power of the noise source to the n _{th} values in the xaxis; in Fig. 4b we extract χ _{−}/2π = 22 kHz from the best fit to Eq. 3.
Discussion
To estimate Γ_{ ϕ }, we assume a typical n _{th} = 0.02.^{14,26} The small χ _{−} leads to Γ_{ ϕ } = 0.25 kHz, corresponding to a photon shot noise limited T _{2} of 4000 μs. In comparison, to achieve the same level of Γ_{ ϕ } with the same n _{th} in a highQcavity device would require κ/2π = 2 kHz (Q ~ 3 × 10^{6}). The T _{1} of the device is Purcell limited^{27} because of the small detuning between the qubit and cavity, evidenced by a measured T _{1} = 21 μs when tuning the qubit to 2.2 GHz below the cavity, and can be improved by increasing cavity Q or engineering the cavity spectrum using filters.^{28,30}
Compared to other methods to suppress photon shot noise dephasing, our approach does not rely on very highQcavities and T _{2} is limited by χ _{−}, which in principle can be tuned to zero. Gate operation and readout can be performed conveniently without dynamical control of the qubit. The planar geometry also makes it easy to integrate the device into larger cQED systems. Potential applications in multiqubit devices include using the TCQ as coupling bus between two transmon qubits to reduce/enhance their crosscoupling strength. The ability to access and measure the quantum state while maintaing the high coherence makes the TCQ a promising building block for the processing and storage of quantum information.
Methods
The device is fabricated on a 500μm thick sapphire substrate. The CPW cavity is defined using photolithography and reactive ion etching of a 200nm film of niobium sputtered on the sapphire. The TCQ is patterned using electron beam lithography and the Josephson junctions are made using bridgefree, doubleangle evaporation.^{31} The chip is mounted and wire bonded to a printed circuit board and cooled down to ~10 mK in a dilution refrigerator. Input signals generated at room temperature are attenuated and filtered at different stages of the refrigerator. Output signals are amplified at 4 K and room temperature and acquired by a highspeed digitizer.
References
Reed, M. D. et al. Realization of threequbit quantum error correction with superconducting circuits. Nature 482, 382–385 (2012).
Lucero, E. et al. Computing prime factors with a Josephson phase qubit quantum processor. Nature Phys. 8, 719–723 (2012).
Córcoles, A. D. et al. Demonstration of a quantum error detection code using a square lattice of four superconducting qubits. Nat. Commun. 6, 6979 (2015).
Houck, A. A. et al. Generating single microwave photons in a circuit. Nature 449, 328–331 (2007).
Hofheinz, M. et al. Synthesizing arbitrary quantum states in a superconducting resonator. Nature 459, 546–549 (2009).
Kirchmair, G. et al. Observation of quantum state collapse and revival due to the singlephoton Kerr effect. Nature 495, 205–209 (2013).
Houck, A. A., Türeci, H. E. & Koch, J. Onchip quantum simulation with superconducting circuits. Nature Phys. 8, 292–299 (2012).
Schmidt, S. & Koch, J. Circuit QED lattices: towards quantum simulation with superconducting circuits. Ann. Phys. 525, 395–412 (2013).
Devoret, M. H. & Schoelkopf, R. J. Superconducting circuits for quantum information: an outlook. Science 339, 1169–1174 (2013).
Reagor, M. et al. Quantum memory with millisecond coherence in circuit QED. Phys. Rev. B 94, 014506 (2016).
Pop, I. M. et al. Coherent suppression of electromagnetic dissipation due to superconducting quasiparticles. Nature 508, 369–372 (2014).
Barends, R. et al. Superconducting quantum circuits at the surface code threshold for fault tolerance. Nature 508, 500–503 (2014).
Paik, H. et al. Observation of high coherence in Josephson junction qubits measured in a threedimensional circuit QED architecture. Phys. Rev. Lett. 107, 240501 (2011).
Rigetti, C. et al. Superconducting qubit in a waveguide cavity with a coherence time approaching 0.1 ms. Phys. Rev. B 86, 100506 (2012).
Blais, A., Huang, R. S., Wallraff, A., Girvin, S. M. & Schoelkopf, R. J. Cavity quantum electrodynamics for superconducting electrical circuits: an architecture for quantum computation. Phys. Rev. A 69, 062320 (2004).
Wallraff, A. et al. Strong coupling of a single photon to a superconducting qubit using circuit quantum electrodynamics. Nature 431, 162–167 (2004).
Gambetta, J. et al. Qubitphoton interactions in a cavity: measurementinduced dephasing and number splitting. Phys. Rev. A 74, 042318 (2006).
Sears, A. P. et al. Photon shot noise dephasing in the strongdispersive limit of circuit QED. Phys. Rev. B 86, 180504 (2012).
Jin, X. Y. et al. Thermal and residual excitedstate population in a 3D transmon qubit. Phys. Rev. Lett. 114, 240501 (2015).
Gambetta, J. M., Houck, A. A. & Blais, A. Superconducting qubit with Purcell protection and tunable coupling. Phys. Rev. Lett. 106, 030502 (2011).
Srinivasan, S. J., Hoffman, A. J., Gambetta, J. M. & Houck, A. A. Tunable coupling in circuit quantum electrodynamics using a superconducting charge qubit with a VShaped energy level diagram. Phys. Rev. Lett. 106, 083601 (2011).
Hoffman, A. J., Srinivasan, S. J., Gambetta, J. M. & Houck, A. A. Coherent control of a superconducting qubit with dynamically tunable qubitcavity coupling. Phys. Rev. B 84, 184515 (2011).
Koch, J. et al. Chargeinsensitive qubit design derived from the Cooper pair box. Phys. Rev. A 76, 042319 (2007).
Dial, O. et al. Bulk and surface loss in superconducting transmon qubits. Supercond. Sci. Technol. 29, 044001 (2016).
Inomata, K., Yamamoto, T., Billangeon, P. M., Nakamura, Y. & Tsai, J. S. Large dispersive shift of cavity resonance induced by a superconducting flux qubit in the straddling regime. Phys. Rev. B 86, 140508 (2012).
Schuster, D. I. et al. AC Stark shift and dephasing of a superconducting qubit strongly coupled to a cavity field. Phys. Rev. Lett. 94, 123602 (2005).
Houck, A. A. et al. Controlling the spontaneous emission of a superconducting transmon qubit. Phys. Rev. Lett. 101, 080502 (2008).
Reed, M. D. et al. Fast reset and suppressing spontaneous emission of a superconducting qubit. Appl. Phys. Lett. 96, 203110 (2010).
Clerk, A. A. & Utami, D. W. Using a qubit to measure photonnumber statistics of a driven thermal oscillator. Phys. Rev. A 75, 042302 (2007).
Bronn, N. T. et al. Broadband filters for abatement of spontaneous emission in circuit quantum electrodynamics. Appl. Phys. Lett. 107, 172601 (2015).
Potts, A., Parker, G. J., Baumberg, J. J. & de Groot, P. A. J. CMOS compatible fabrication methods for submicron Josephson junction qubits. IEE. Proc. Sci. Meas. Technol. 148, 225–228 (2001).
Acknowledgements
This work is supported by IARPA under contract W911NF1010324.
Competing interests
The authors declare no competing interests.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhang, G., Liu, Y., Raftery, J.J. et al. Suppression of photon shot noise dephasing in a tunable coupling superconducting qubit. npj Quantum Inf 3, 1 (2017). https://doi.org/10.1038/s4153401600022
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1038/s4153401600022
This article is cited by

Nonlinear germaniumsilicon photodiode for activation and monitoring in photonic neuromorphic networks
Nature Communications (2022)

Analytical solution for nonadiabatic quantum annealing to arbitrary Ising spin Hamiltonian
Nature Communications (2022)

Quantum Optimal Control: Practical Aspects and Diverse Methods
Journal of the Indian Institute of Science (2022)

Cheatsensitive coin flipping and quantum gambling
Quantum Information Processing (2022)

Experimental measurement of bipartite entanglement using parameterized quantum circuits
Science China Physics, Mechanics & Astronomy (2022)