Abstract
The Casimir Effect is a physical manifestation of quantum fluctuations of the electromagnetic vacuum. When two metal plates are placed close together, typically much less than a micron, the long wavelength modes between them are frozen out, giving rise to a net attractive force between the plates, scaling as d^{−4} (or d^{−3} for a sphericalplanar geometry) even when they are not electrically charged. In this paper, we observe the Casimir Effect in ambient conditions using a modified capacitive microelectromechanical system (MEMS) sensor. Using a feedbackassisted pickandplace assembly process, we are able to attach various microstructures onto the postrelease MEMS, converting it from an inertial force sensor to a direct force measurement platform with pN (piconewton) resolution. With this system we are able to directly measure the Casimir force between a silvercoated microsphere and goldcoated silicon plate. This device is a step towards leveraging the Casimir Effect for cheap, sensitive, room temperature quantum metrology.
Introduction
One of the most commonly used technologies enabled by microelectromechanical systems (MEMS) are inertial sensors^{1,2}. These devices are a part of our everyday lives, from sensing the orientation of smartphones (low g) to detecting collisions in automobiles in order to deploy airbags (high g). Current stateoftheart low g MEMS inertial sensors are capable of sensing sub millig accelerations with noise densities of around 0.1 mg/Hz^{1/2} or less^{3,4,5}. The proofmass of these sensors typically weigh around 1 μg, meaning the devices are capable of resolving forces below 1 pN. Such force sensitivity is comparable to the performance of an atomic force microscope (AFM), but is realized on a single millimeterscale chip and costs just tens of dollars per device. In this work, we show that by attaching a silvercoated microsphere to its proofmass, a commercial MEMS inertial sensor can measure the Casimir force that is exerted onto the microsphere, and therefore directly onto the proofmass of the sensor, due to its interaction with an external metallized plate.
The Casimir Effect, first derived by Hendrik Casimir in 1948, is a quantum fluctuation force that exists between conducting surfaces separated by hundreds of nanometers^{6}. In its simplest case (two perfectly smooth, perfectly conducting planar surfaces), the Casimir Effect manifests itself as an attractive force between the two objects, which scales as one over separation to the fourth power. The physical origin of this phenomenon is purely quantum mechanical, arising from zeropoint fluctuations exerting a net pressure on the conducting surfaces. Because of the small scale of this effect (pN forces at nanometer separations), Casimir force detection nearly always involves a micromechanical system of some kind. Most commonly a modified AFM setup is used, in which a cantilever is adapted to measure forces exerted on it due to Casimir interactions^{7,8,9,10}. Other work using MEMS has made use of torsional resonators^{11,12,13}. Additionally, devices that can integrate both Casimir surfaces onto a single chip^{14} are less prone to lowfrequency noise and thermal drift due to smaller components and higher mechanical resonant modes, but come at the cost of reduced interaction area and limited separation ranges.
The main advantage of a modified commercial MEMS sensor is the preoptimized design of the MEMS, and the supporting integrated circuitry simplify the device fabrication and apparatus immensely. Despite using an external piezomounted plate, we are able to clearly see the Casimir force in ambient conditions. Compared to AFM, the size and cost is superior by orders of magnitude and the linear transduction of an applied force to an electronic output signal is a builtin feature of the sensor.
The ability to measure the Casimir Effect with commercial MEMS devices is an exciting prospect because it indicates that this effect could be used as a practical, controllable engineering tool within a MEMS system. For example, it has been suggested that a MEMS oscillator parametrically driven by the Casimir force would exhibit a gain that scales as one over the Casimir cavity size to the fifth power or as applied direct current (DC) voltage to the tenth power^{15}. In addition to providing a means of investigating the Casimir Effect itself, this system could be useful for temperature sensing, alternate current (AC) voltage measurements, lowimpedance current measurements, or probing any measurand, which could be coupled into a physical movement of the sensor proofmass. Successfully integrating a Casimir cavity into a welldeveloped, scalable MEMS device is an important step in realizing Casimirenabled sensors as a practical, room temperature quantum metrology tool.
Results
Casimir cavity integration with MEMS
Microgluing onto postrelease MEMS
Because the modification involves bonding objects to a postrelease MEMS device, great care must be taken in keeping mechanical forces exerted on the freely moving parts to a minimum. We present a technique that allows us to glue microspheres directly to the proofmass of a MEMS inertial sensor without compromising its functionality. In this work, we use an accelerometer from Analog Devices (ADXL203), pictured in Fig. 1a.
Outlined in Fig. 1b is our process which involves depositing picoliter volume droplets of ultraviolet (UV) curable epoxy using a micropipette attached to a piezoelectric actuator onto the proofmass then placing a microsphere onto the droplet using a probe tip (contact forces are sufficient to pick up the microsphere). The pipette or probe tip can be moved in plane with a micromanipulator, while the Z position is controlled with nanometer precision using the piezoelectric actuator. The advantage of assembling onto postrelease MEMS is that we can sense when contact with the proofmass occurs by actively monitoring the noise on the outputs of the device (see Fig. 1b). This feedback is what allows us to deposit droplets gently onto the proofmass without forcing liquid into the release holes or breaking the springs. As can be seen in Fig. 1c, the proofmass (shown in blue) provides only a few small areas over which droplets can be placed without interfering with other parts of the MEMS such as the sensing fingers or the springs. In order to attach larger objects, we use one or more spheres (Aucoated solid barium titanate glass) as supports for other objects to be set upon, like legs of a table. Once these “legs” are formed, one can then attach a wide variety of microscale objects, provided they do not interfere with the MEMS and are able to be picked up and placed gently. For example, it is possible to place a submillimeter neodymium rareearth magnet on top of the support spheres for highresolution gradient magnetometry (on going work). For the device presented in this paper, two 30 µm diameter solid spheres were glued onto the proofmass as a platform for the rest of the assembly discussed below.
Casimir force detection
The functional component of our device is a conductive microsphere attached to the proofmass of the inertial sensor that forms onehalf of the Casimir cavity. Doing this results in a device that can not only measure accelerations applied to the device body (as was originally intended) but also forces exerted directly onto the sphere, namely electrostatic and Casimir forces. The sphere is 55 µm in radius and made of hollow borosilicate glass coated with 50 nm of Ag and has a mass of roughly 0.1 µg. It was found that Agcoated hollow spheres had much lower surface roughness than Aucoated solid spheres (Supplementary information S1), so an Ag sphere was used in the Casimir cavity, while two smaller Au spheres (about 0.5 µg each) were used as supports. It should be noted that the mass added to the proofmass does not affect the functionality of the device at DC. For dynamic measurements, however, the added mass does lower the overall bandwidth of the device.
One requirement in any Casimir device is the ability to control the electric potential on the interacting surfaces. This is due to the presence of residual electrostatic forces, which are caused by trapped charges, adsorbates, and the polycrystalline nature of the metallic surfaces^{16,17,18}. The latter results in local differences in the work function of the materials (also known as patch potentials), which sum up to a nonzero effective potential difference, even when the materials are electrically connected^{19}. This overall residual potential is a common source of error in Casimir force measurements if not controlled for. To do this, a 500nmthick serpentine ribbon wire connects the surface of the Ag microsphere to an open bonding pad on the ceramic package. The conductivity of the wire provides a means of controlling the voltage on the sphere and its flexible geometry ensures a low spring constant, thus allowing for minimal restriction of the motion of the proofmass and the restoring force of the polysilicon springs. The effect that the wire has on the overall effective spring constant of the system (and therefore the force sensitivity) is minimal and easily accounted for as the postmodification force sensitivity is recalibrated by using known electrostatic forces between the sphere and the plate. Additionally, because the electrostatic calibration is done with the sphere and plate in the same configuration as the Casimir force measurement, any rotational movement of the proofmass due to torque applied from the sphere (which is not perfectly centered) will be accounted for. The process of assembling this device is shown schematically in Fig. 1d and discussed further in Methods.
The second half of the Casimir cavity is formed from a Aucoated plate mounted on a linear piezoelectric actuator. For the device used in this paper, the plate approaches the sphere along the Xaxis of the sensor. The entire setup is mounted on an optical breadboard and contained in a temperaturecontrolled enclosure on top of an active vibration isolation table. A schematic of the device and apparatus can be seen in Fig. 2b.
Device performance
Electrostatic characterization of residual potential and force calibration
Electrostatic forces are used to measure the residual potential difference, V_{0}, between the sphere and the plate and to calibrate the force sensitivity, γ, which relates the sensor output voltage, S, to the applied force according to F = γS. In Fig. 2c we plot the voltage output in the X direction, S_{X}, as we vary the potential applied between the grounded plate and the microsphere (V_{bias}) at different separations between 200 nm and 1 µm where electrostatic forces are much larger than the Casimir force. The minima of these voltage sweeps indicate the bias that cancels residual potential between the metal surfaces, and the curvature of the sweeps give a calibration coefficient between the sensor voltage output and force, which can then be used for Casimir force measurements (see further discussion on this approach in Methods).
Both the residual potential and the force sensitivity of the device appear to be functions of separation and are approximately linear. Over the full 800 nm scan range, it is observed that V_{0} varies by 9% and γ varies by 20%, with average values of 0.21 V and 33.5 pN/mV, respectively.
Casimir force measurement
The data in Fig. 3 is a measurement of the force applied to the proofmass along its X axis as a function of separation between the Agcoated microsphere (which is attached directly to the proofmass) and an external Aucoated plate. Electrostatic contributions have been minimized according to the methodology discussed in the following sections. The red and black data points are the same set of data fit to either the ideal Casimir force theory (solid red line) given by Eq. 8 or the corrected Casimir force theory (solid black line) given by Eq. 12 with only x_{s} (i.e., where separation d = 0) as a free parameter. According to the ideal fit, the last measured data point at 635.5pN is 65 nm away from d = 0. According to the corrected Casimir fit, the last measured data point is 63 nm away from d = 0.
Discussion
Distance dependence of residual potential and sensitivity
The separation dependence of the residual potential is a wellknown occurrence^{20,21,22} as the potential measured is an effective sum of the contributions from different regions across the surfaces of each metal. As the separation changes, these contributions will sum differently due to the inverse square dependence of the electrostatic force. The linear dependence of the force sensitivity of the device is due to the interaction of the grounded Si plate with the fringe fields of the interdigitated capacitor fingers of the sensor. The capacitive sensing relies on a small AC signal applied between the fixed fingers and the movable fingers. Because the plate is held at the same ground as the device, it will deflect fringe field lines from this applied voltage and result in an outofplane force exerted on the grounded fingers^{23,24}. As the plate’s position is varied it will overlap with more fringe fields, thus exerting a larger out of plane force and decreasing the sensitivity. This effect is more prominent the closer the plate is to the fingers (see Supplementary information S2). Therefore, there is an ideal range of plate heights at which the experiment can be performed, where the fringe field interactions are minimized while also ensuring adequate area of interaction between the side of the sphere and the plate.
Casimir force comparison with theory
In Fig. 3 it can be observed that the measured data is modeled more accurately by the ideal Casimir theory (root mean squared error of 7.4pN) compared to the corrected theory (root mean squared error of 10.5pN). While the corrected theory takes into account the finite conductivity and nonzero temperature of the surfaces, the perturbation approach used in ref. ^{25} is in fact only valid for separations ranging from a few hundred nanometers to several micrometers. At short separations, the dielectric permittivity of the respective metals at high frequencies contributes to the force magnitude and changes the scaling with separation (V.M. Mostepanenko, personal communication, October 26, 2018). As a result, although the ideal theory overestimates the measured force in the 80 to 200 nm range, the corrected model in Eq. 12 underestimates it by far greater. More accurate fitting may be possible by performing a numerical calculation of the Lifshitz formula using optical data for the complex index of refraction of the metal surfaces, but such analysis is outside the scope of this work.
Considering random measurement errors, the linear fits shown in Fig. 2d returned root mean square errors to the data of 1.8 mV and 0.6pN/mV for V_{0} and γ, respectively. Assuming a miscalculated V_{0} off by three standard deviations (5.4 mV) at the closest point of approach of 60 nm, we would be introducing an unwanted additional electrostatic force of 0.74 pN, which is just 0.1% of the Casimir force measured at that point. This value is also much less than the random error in the force measurement due to uncertainty in the product γS_{X} (whose combined errors propagate to as high as 60 pN at the closest measured point). It is therefore likely that the discrepancy between measurement and theory in this distance range are not due to imperfectly canceled electrostatic forces, as the Casimir force is the dominant interaction.
The reason for this discrepancy is most likely due to the assumptions of the geometry of the cavity, both at the microscale (i.e., sphere and plate shapes and arrangement) and at the nanoscale (surface roughness). The sphere radius, R, is used in both the electrostatic calibration analysis as well as the theoretical Casimir fits. In both cases, we use R in the framework of the proximity force approximation (PFA), which assumes a perfectly spherical surface and an infinite plane in the d « R limit^{26}. Because of this, both the calibration factor and the Casimir force are proportional to R, so any errors in the value of R (which was measured optically) do not affect the fitting. However, if the sphere is not perfectly spherical, then we would expect both the electrostatic force and the Casimir force to scale differently depending on the exact shape^{27}. Additionally, due to physical constraints of our setup, the plate is limited to extend only ∼80–90 µm below the central plane of the sphere. Because the PFA assumes an infinite plane, this asymmetry may result in a systematically overestimated force sensitivity of the device.
The surface roughness also becomes very important in Casimir interactions at separations <∼ 100 nm^{28,29}. The AFM scans taken were on separate samples (see supplementary information S1), which went through the same coating processes as the sphere and plate used in this device. While this may be useful for capturing average roughness values, it is not specific to this exact cavity, which may have extreme asperities that cause deviation from the expected scaling below 100 nm separations. To improve both of these geometryrelated systematic uncertainties, characterization of individual spheres would need to be done prior to subsequent assembly.
Nevertheless, our results show that an Ag surface and an Au surface in our atmospheric MEMS system exhibit an interaction that can be described quite well by the ideal Casimir force model. This is a promising finding as we move forward with Casimirenabled sensing devices, such as that described by Imboden et al^{15}. The results presented here imply that approximating this interaction as a simple inverse cubic relation is quite sufficient for further analysis and modeling.
Conclusions
The purpose of this work was twofold: First, we have successfully integrated a Casimir cavity onto a MEMS system, which is capable of resolving piconewton forces. This system provides the experimenter with a customizable apparatus for investigating the Casimir Effect with nontrivial geometries, materials, or surface morphologies such as nanostructures or chiral metamaterials^{30,31,32,33,34}. Additionally, this work is an important stepping stone in our goal to leverage the extraordinary distance dependence of the Casimir force to provide an enhancement in the sensitivity of the device through parametric techniques. Second, we have shown that it is possible to perform highly sensitive quantum metrology in ambient conditions with offtheshelf consumer MEMS sensors, which are widely available and very inexpensive. Once functionalized, these devices can be used as a novel tool for experimenters—a literal platform capable of performing a variety of interesting micro and nanoscale lowforce experiments. Using the feedbackassisted microgluing process we have developed, one can repurpose the sensor to transduce any measurand that can be coupled into a displacement of the proofmass.
Materials and methods
MEMS sensor
The fundamental building block of our Casimir measurement system is a MEMS accelerometer from Analog Devices (ADXL203)—a twoaxis capacitive accelerometer with analog voltage outputs for the inplane X and Y directions with a sensitivity of ∼ 1 V/g along both axes^{5}. The polysilicon MEMS consists of an octagonal proofmass (760 µm in width and 4 µm in thickness) that is anchored to the substrate via four serpentine springs with a total effective spring constant of roughly 1 N/m. The proofmass/spring system has a fundamental resonant mode at 5.4 kHz with a quality factor of 10 in air and 1000 in vacuum (∼1 × 10^{−4} Torr). The proofmass also has four sets of finger electrodes, forming an interdigitated differential capacitor with another set of fingers anchored to the substrate. Any force applied to the proofmass moves it, thus changing this capacitance. The proofmass is surrounded by integrated circuitry on the same chip that demodulates the signals from the differential capacitance measurements and rectifies them into two independent output voltages (nominally 2.5 V with zero applied acceleration) that are proportional to the position of the proofmass in the X and Y directions. Because the springs obey Hooke’s Law, the outputs are linearly proportional to the forces on the proofmass. This platform has been optimized with its sensing circuit integrated with the MEMS process to produce a very low noise system that can resolve forces of ∼1pN applied directly to the proofmass. The package is easily opened with a straight edge razor blade. After the lid is removed, the MEMS proofmass and electronics can be seen as shown in Fig. 1a.
Device assembly
To assemble this device, the following process (outlined in Fig. 1d) was developed: (1) a serpentine wire with circular ends is fabricated by lithographically patterning and etching a 500nmthick layer of Au on top of a 2 µm layer of thermally grown oxide. The wire is then released by removing the oxide in hydrofluoric acid (i–iv). 2) A single 55µm radius hollow borosilicate glass sphere coated with 50 nm of Ag (from Cospheric Technologies), which will function as onehalf of the Casimir cavity, is glued to one end of the serpentine wire using Ag epoxy (Lake Shore Cryotronics, cured by heating at 80 °C for 3 h). This provides electrical connection between the wire and the surface of the sphere. (3) The wire is picked up by the end opposite to the sphere by gluing it to the end of a glass micropipette using UV curable epoxy (v, vi). (4) The wire/sphere is lifted off of the substrate, dipped in UV curable epoxy (Norland Optical NOA81), and positioned over the support spheres. (5) The wire/sphere is lowered using a piezoelectric actuator. Contact is determined by monitoring the noise on the X and Y outputs of the sensor, as with the gluing process shown in Fig. 1b. When contact is made, the epoxy is cured by UV exposure with a 365 nm lightemitting diode source (vii). (6) The other end of the wire which is glued to the micropipette is brought over to a pad on the ceramic package and glued down using Ag epoxy. (7) Finally, the wire is released by breaking off the end of the micropipette (viii). An example of a fully assembled device can be seen in Fig. 1e. The device used for the results in this paper (along with the external Aucoated plate) can be seen in the optical image in Fig. 2a.
The plate is fabricated from a 300µmthick silicon wafer, etched into a tapered shape using photolithography and DRIE, and then coated with 10 nm Cr adhesion layer followed by 150 nm of Au using electron beam evaporation.
Apparatus and experimental details
The modified ADXL203 is mounted on an XY translation stage attached to an optical breadboard. On the same breadboard is another XYZ stage on which the plate is mounted. This stage has its Z position controlled by a Newport Picomotor stickslip piezoelectric actuator. An additional Newport NPC3SG piezoelectric stack actuator controls the fine position of the plate in the X direction. The apparatus is contained inside a polystyrene foam container along with a 50 Ω power resistor and resistance temperature detector for ProportionalIntegralDerivative controlled temperature with a 28 °C setpoint. Due to building heaters cycling on and off, the maximum temperature variations inside the enclosure over long periods of time are ∼12 m°C; however, for shorter time periods (2 h or less), the temperature can be held within ∼3 m°C (see Supplementary information S3). The container is set upon an active vibration isolation table (Herzan TS140).
The potential between the sphere and plate is controlled by grounding the plate and applying a voltage on the sphere through the nanoribbon wire using a 1 mV resolution power supply (Keithley Instruments). Due to a proprietary polymer coating on the ADXL203 MEMS and the insulating UV curable epoxy, there is no electrical connection between the sphere and the proofmass.
The sensor voltage output is fed directly into a lowpass filter (Stanford Research Systems SR650) with a 3 Hz cutoff frequency and unity gain. The filter output is then sampled by an ADC (National Instruments NIDAQ).
Measurement and calibration theory and methods
Electrostatic force
As discussed previously, electrostatic forces are present between the sphere and plate metal surfaces, even when the two metals are shorted together. By applying a voltage equal and opposite to the residual potential, this unwanted electrostatic effect can by minimized. Additionally, by applying known electrostatic forces between the plate and the sphere, the force sensitivity of the output can be calibrated.
The forces acting on the sphere are assumed to be only due to electrostatic and Casimir interactions. For the following equations, we define the separation: d = x_{p} − x_{s}, where x_{p} is the absolute position of the plate and x_{s} is the absolute position of the sphere. Assuming a simple electrostatic model, we can write:
where ε_{0} is the permittivity of free space, V_{0} is the residual potential, V_{bias} is the applied DC voltage between the sphere and plate, and R is the radius of the sphere. Equation 1 uses the PFA for a sphereplate geometry, which assumes d « R. At large separations (typically > 200 nm) and large applied voltages (V_{0} + V_{bias} > 100 mV), the Casimir force term is negligible, and the force scales as V_{bias}^{2}. The residual potential can be measured by sweeping the bias voltage and finding the value of V_{bias} at which the force is minimized. At this minimum, the applied bias is equal and opposite to the residual potential.
The sensor outputs an analog voltage, so to get a measurement in units of force, a calibration must be performed. Because of the linear response of the device, the output signal, S, is proportional to the force applied on the proofmass by a constant, γ:
For large separations and voltages, we can ignore the Casimir term in Eq. 1 and can now write:
We can then write γ in terms of the second derivative of the signal with respect to V_{bias}:
From these relations, the residual potential and force sensitivity can be measured by fitting the raw signal data, S, to the function S = c_{1}V_{bias}^{2} + c_{2}V_{bias} + c_{3}. Using the returned fitting parameters we can calculate:
provided we are in a region where the electrostatic force is dominant over the Casimir force.
The procedure for a single measurement is as follows—first the plate is moved by steps of 20 nm towards the sphere until contact is sensed. The plate is then retracted by 1 µm and V_{bias} is swept, tracing out a parabola as shown in Fig. 2c, according to Eq. 3. More sweeps are taken as the plate is moved closer by steps of 100 nm. Every data point is the average of 50,000 samples taken in 0.5 s by the ADC with standard deviations between 0.6 and 0.7 mV. The whole electrostatic measurement takes 3.5 min. Over this period of time, thermal drift is negligible (see Supplementary information S3). Fitting a secondorder polynomial to these data sets provides measurements of the residual potential, V_{0}, as well as the sensitivity, γ, according to Eqs. 5 and 6. These values are plotted in Fig. 2d.
Casimir force
For ideal conditions (absolute zero temperature and perfectly smooth infinitely conducting surfaces), the Casimir force between two plates of area A is given by ref. ^{6} as:
where ħ is Planck’s reduced constant, c is the speed of light in vacuum, and A is the overlap area between the surfaces. Using PFA for a sphereplate geometry, this becomes:
provided d « R, as in the electrostatic case. In addition to this ideal case, we consider a corrected model from Geyer et al.^{25}, which accounts for more realistic physical effects such as nonzero temperature and the finite conductivity of both metallic surfaces. In this model, a perturbation expansion in powers of the relative penetration depths of electromagnetic oscillations into each metal (using a plasma model) provides a corrected equation for the Casimir force given as:
Here, ζ is the Reimann zeta function, t is a parameter given by t = (ħc)(2k_{B}Td)^{−1}, and δ and κ are optical parameters given by:
where δ_{Au} and δ_{Ag} are the effective penetration depths of the electromagnetic oscillations into each metal film given by ħc/ω_{p}, in which we have used ω_{p} = 9 eV for Au and ω_{p} = 8.6 eV for Ag^{35}. Equation 9 is a limiting case of this theory in which 1/t « 1, which is a valid approximation at our operating temperature (T = 301.15 K) and d < 1 µm. Finally, a secondorder correction for surface roughness is included:^{7,36}
where A_{r} is the stochastic RMS roughness amplitude of both surfaces. The surface roughness of the plate and sphere surfaces were found to be 2 and 8 nm, respectively, using AFM (supplementary information S1). The total RMS roughness used in this model is A_{r} = (A_{r,sphere}^{2} + A_{r,plate}^{2})^{1/2} = 8.25 nm.
Immediately following the electrostatic measurement, the plate is retracted back 1 µm away from the sphere and then stepped forward by 1 nm increments as V_{bias} is adjusted according to the linear fit, ensuring that the first term of Eq. 1 is minimized at every position. At each plate position, 50,000 samples are taken in 0.5 s using the ADC. This measurement takes 20 min, which requires that the enclosure temperature remain within 3 m°C to avoid unwanted thermal drift (see Supplementary information S3).
After subtracting the zeroforce signal (c_{3}), the measured data is scaled to units of force using the calibration factor γ(d) measured from the electrostatic data. It is then fit to either the ideal Casimir theory (Eq. 8) or the corrected Casimir theory (Eq. 12), with x_{s} as the only free parameter. These results can be seen in Fig. 3.
References
Perlmutter, M. & Robin, L. Highperformance, low cost inertial MEMS: a market in motion. Proceedings of IEEE/ION PLANS. Myrtle Beach, South Carolina pp. 225–229 (2012).
Barbour, N. & Schmidt, G. Inertial sensor technology trends. IEEE Sens. J. 1, 332–339 (2001).
Tez, S., Aykutlu, U., Torunbalci, M. M. & Akin, T. A bulkmicromachined threeaxis capacitive MEMS accelerometer on a single die. J. Microelectromech. Syst. 24, 1264–1274 (2015).
Sabato, A., Niezrecki, C. & Fortino, G. Wireless MEMSbased accelerometer sensor boards for structural vibration monitoring: a review. IEEE Sens. J. 17, 226–235 (2017).
Data Sheet ADXL103/ADXL203. Tech. Rep., Analog Devices (2018). URL http://www.analog.com/media/en/technicaldocumentation/datasheets/ADXL103_203.pdf
Casimir, H. On the attraction between two perfectly conducting plates. Proc. K. Ned. Akad. 360, 793–795 (1948).
Mohideen, U. & Roy, A. Precision measurement of the Casimir force from 0.1 to 0.9 μm. Phys. Rev. Lett. 81, 4549–4552 (1998).
Roy, A. & Mohideen, U. Demonstration of the nontrivial boundary dependence of the casimir force. Phys. Rev. Lett. 82, 4380–4383 (1999).
Van Zwol, P. J., Palasantzas, G., Van De Schootbrugge, M. & De Hosson, J. T. M. Measurement of dispersive forces between evaporated metal surfaces in the range below 100 nm. Appl. Phys. Lett. 92, 054101 (2008).
Garrett, J. L., Somers, D. A. T. & Munday, J. N. Measurement of the Casimir Force between two spheres. Phys. Rev. Lett. 120, 40401 (2018).
Chan, H. B., Aksyuk, V. A., Kleiman, R. N., Bishop, D. J. & Capasso, F. Quantum mechanical actuation of microelectromechanical systems by the Casimir force. Science 291, 1941–1944 (2001).
Chan, H. B., Aksyuk, Va, Kleiman, R. N., Bishop, D. J. & Capasso, F. Nonlinear micromechanical Casimir oscillator. Phys. Rev. Lett. 87, 211801 (2001).
Decca, R. S., Lόpez, D., Fischbach, E. & Krause, D. E. Measurement of the Casimir force between dissimilar metals. Phys. Rev. Lett. 91, 3–6 (2003).
Zou, J. et al. Casimir forces on a silicon micromechanical chip. Nat. Commun., 1845 4 (2013).
Imboden, M., Morrison, J., Campbell, D. K. & Bishop, D. J. Design of a Casimirdriven parametric amplifier. J. Appl. Phys. 116, 1–18 (2014).
Van Blokland, P. H. G. M. & Overbeek, J. T. G. Van der Waals forces between objects covered with a chromium layer. J. Chem. Soc. Faraday Trans. 1 74, 2637–2651 (1978).
Lamoreaux, S. K. Demonstration of the Casimir force in the 0.6 to 6 μm range. Phys. Rev. Lett. 78, 5–8 (1997).
Nonnenmacher, M., O’Boyle, M. P. & Wickramasinghe, H. K. Kelvin probe force microscopy. Appl. Phys. Lett. 58, 2921–2923 (1991).
Speake, C. C. & Trenkel, C. Forces between conducting surfaces due to spatial variations of surface potential. Phys. Rev. Lett. 90, 4 (2003).
Kim, W. J., BrownHayes, M., Dalvit, D. A. R., Brownell, J. H. & Onofrio, R. Anomalies in electrostatic calibrations for the measurement of the Casimir force in a sphereplane geometry. Phys. Rev. A 78, 020101 (2008).
De Man, S., Heeck, K. & Iannuzzi, D. No anomalous scaling in electrostatic calibrations for Casimir force measurements. Phys. Rev. A 79, 4–7 (2009).
Behunin, R. O., Intravaia, F., Dalvit, D. A., Neto, P. A. & Reynaud, S. Modeling electrostatic patch effects in Casimir force measurements. Phys. Rev. A 85, 1–9 (2012).
Tang, W. C., Lim, M. G. & Howe, R. T. Electrostatic comb drive levitation and control method. J. Microelectromech. Syst. 1, 170–178 (1992).
Imboden, M., Morrison, J., Lowell, E., Han, H. & Bishop, D. J. Controlling levitation and enhancing displacement in electrostatic comb drives of MEMS actuators. J. Micro. Syst. 23, 1063–1072 (2014).
Geyer, B., Klimchitskaya, G. L. & Mostepanenko, V. M. Perturbation approach to the Casimir force between two bodies made of different real metals. Phys. Rev. A 65, 062109 (2002).
Derjaguin, B. Untersuchungen über die Reibung und Adhäsion, IV. Theorie des Anhaftens kleiner Teilchen" [Analysis of friction and adhesion, IV. The theory of the adhesion of small particles]. Kolloid Z. (in German). 69, 155–164 (1934).
Gies, H. & Klingmϋller, K. Worldline algorithms for Casimir configurations. Phys. Rev. D 74, 1–12 (2006).
Van Zwol, P. J., Palasantzas, G. & De Hosson, J. T. M. Influence of random roughness on the Casimir force at small separations. Phys. Rev. B 77, 1–5 (2008).
Broer, W., Palasantzas, G., Knoester, J. & Svetovoy, V. B. Roughness correction to the Casimir force at short separations: contact distance and extreme value statistics. Phys. Rev. B. 85, 1–13 (2012).
Zhao, R., Zhou, J., Koschny, T., Economou, E. N. & Soukoulis, C. M. Repulsive casimir force in chiral metamaterials. Phys. Rev. Lett. 103, 1–4 (2009).
Van Zwol, P. J. & Palasantzas, G. Repulsive Casimir forces between solid materials with highrefractiveindex intervening liquids. Phys. Rev. A 81, 1–9 (2010).
Intravaia, F. et al. Strong casimir force reduction through metallic surface nanostructuring. Nat. Commun. 4, 2515 (2013).
Woods, L. M. et al. Materials perspective on Casimir and van der Waals interactions. Rev. Mod. Phys. 88, 045003 (2016).
Tang, L. et al. Measurement of nonmonotonic Casimir forces between silicon nanostructures. Nat. Photonics 11, 97–101 (2017).
Rioux, D. et al. An analytic model for the dielectric function of Au, Ag, and their Alloys. Adv. Opt. Mater. 2, 176–182 (2014).
Maradudin, A. A. & Mazur, P. Effects of surface roughness on the van der Waals force between macroscopic bodies. Phys. Rev. B 22, 1677–1686 (1980).
Acknowledgements
We would like to thank Diego Perez, Jackson Chang, and Corey Pollock for helpful consultations regarding device fabrication, and David Lloyd for assistance with the collection of AFM data. We would also like to thank V.M. Mostepanenko for very useful discussions on the theory. This work is funded by the National Science Foundation grant no. 1708283, the Engineering Research Centers Program of the National Science Foundation through NSF Cooperative Agreement under Grant EEC0812056, Grant EEC1647837, and Grant ECCS1708283, and the DARPA Atoms to Product (A2P) Program/Air Force Research Laboratory (AFRL) contract no. FA865015C7545.
Author information
Authors and Affiliations
Contributions
The device and experiments were conceived by D.J.B. and A.S. The fabrication was done by A.S. with assistance from J.J. All data were collected by A.S. and interpreted and analyzed by A.S., L.K.B., and D.J.B. The manuscript was written by A.S. with input from M.I. and edited by all authors.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Stange, A., Imboden, M., Javor, J. et al. Building a Casimir metrology platform with a commercial MEMS sensor. Microsyst Nanoeng 5, 14 (2019). https://doi.org/10.1038/s4137801900545
Received:
Revised:
Accepted:
Published:
DOI: https://doi.org/10.1038/s4137801900545
This article is cited by

Zeptometer Metrology Using the Casimir Effect
Journal of Low Temperature Physics (2022)

Analysis of a Casimirdriven parametric amplifier with resilience to Casimir pullin for MEMS singlepoint magnetic gradiometry
Microsystems & Nanoengineering (2021)

Casimir spring and dilution in macroscopic cavity optomechanics
Nature Physics (2020)

A system for probing Casimir energy corrections to the condensation energy
Microsystems & Nanoengineering (2020)

100 pT/cm singlepoint MEMS magnetic gradiometer from a commercial accelerometer
Microsystems & Nanoengineering (2020)