Optical frequency synthesizers have widespread applications in optical spectroscopy, frequency metrology, and many other fields. However, their applicability is currently limited by size, cost, and power consumption. Silicon photonics technology, which is compatible with complementary-metal-oxide-semiconductor fabrication processes, provides a low-cost, compact size, lightweight, and low-power-consumption solution. In this work, we demonstrate an optical frequency synthesizer using a fully integrated silicon-based tunable laser. The synthesizer can be self-calibrated by tuning the repetition rate of the internal mode-locked laser. A 20 nm tuning range from 1544 to 1564 nm is achieved with ~10−13 frequency instability at 10 s averaging time. Its flexibility and fast reconfigurability are also demonstrated by fine tuning the synthesizer and generating arbitrary specified patterns over time-frequency coordinates. This work promotes the frequency stability of silicon-based integrated tunable lasers and paves the way toward chip-scale low-cost optical frequency synthesizers.
In the past two decades, there has been much research and development in optical frequency synthesizers (OFSs), which are able to generate accurate and stable optical frequencies from a single microwave frequency reference. OFSs have enabled a wide range of applications in frequency metrology1,2,3, precise navigation4,5,6, optical spectroscopy7,8,9, microwave photonics10,11,12, and so on. However, applications are often limited to scientific experiments due to the size, weight, power consumption, and cost of OFSs. To improve their applicability, OFSs based on chip-scale-integrated photonic devices have been proposed and demonstrated13,14,15,16,17. Among different kinds of integrated photonics platforms, silicon photonics technology has been extensively developed to meet the increasing demand for data communication bandwidth. Since it is compatible with the mature complementary-metal-oxide-semiconductor (CMOS) fabrication technology, this technology can cost-effectively mass-produce chip-scale devices on the wafer level. Therefore, silicon photonics is a promising candidate to radically reduce the volume and cost of OFSs and eventually bring all the benefits of OFSs from the laboratory to our daily lives.
A tunable laser (TL) is one of the most important elements in an OFS since it acts as the source of the final output optical signal of the synthesizer. Recently, rare-earth-doped integrated lasers have been developed on silicon photonics platforms. These kinds of lasers possess several advantages that make them suitable for chip-scale OFSs. First, the gain media can be deposited through a single-step back-end-of-line process, enabling CMOS-compatible monolithic laser integration for low-cost mass production18. Common rare-earth elements such as erbium, thulium, and holmium have broad gain bandwidths, which enable wide tunability over different wavelength regions19,20,21,22,23. Furthermore, rare-earth-doped integrated lasers can achieve narrow linewidths since these materials do not involve free carriers in the pumping process24,25,26. In addition, the host material of the gain elements has low thermo-optic coefficients and hence enables lasers with good thermal stability27,28. Although the performance of these silicon photonics-integrated lasers has been fully characterized on the device level, it is still unknown if they are qualified for OFSs, which need much more stringent requirements than free-running integrated lasers in terms of frequency instability, tuning precision, reconfigurability, and so on.
To this matter, an OFS using a silicon photonics-based integrated TL is demonstrated in this work. By carefully designing the tuning mechanism and control electronics, a large tuning range with precise and flexible tuning, high frequency stability and self-frequency calibration is achieved simultaneously. Therefore, the uncertainty associated with integrated TLs, which is one of the largest technical risks that prohibit the realization of chip-scale OFSs, is eliminated.
The architecture of an OFS is shown in Fig. 1. It consists of an integrated erbium TL29 and a mode-locked laser (MLL). We choose a commercial MLL so that we can focus on the technical limitations of the integrated TL device in an OFS system. After stabilizing the fceo and frep of the MLL and locking the frequency of the TL to one comb line of the MLL, the output of the TL can serve as the synthesizer output. The detailed circuits of the three locking blocks, fceo locking, frep locking, and TL-to-comb locking, are shown in Fig. 2a–c, respectively. Based on these locking electronics, the synthesizer output frequency is given by:
where M is the comb line mode number of the MLL and f1, f2, and f3 are the output frequencies of RF synthesizers 1, 2, and 3 in Fig. 2a–c, respectively. Since RF synthesizers 1, 2, and 3 are referenced to the same 10 MHz signal, the RF frequency (10 MHz) stability is transferred to the optical frequency fSN. This frequency stability transfer is the fundamental purpose of building an OFS.
Mode number calibration
The mode number, M, can be decided by a calibration procedure30 with the TL-to-comb circuit unlocked. As shown in Fig. 3a, we use a computer to control the reference frequency, f1, within the frep locking circuit of the MLL in Fig. 2a so that the repetition rate of the MLL always follows a change in f1. We first continuously increase f1 while tracing the beat note, fb, between the TL and the MLL. When fb has increasingly passed a specified frequency, fb0, N times, we record the instantaneous frequencies f12 and fb2. Subsequently, we continuously decrease f1. Once fb has decreasingly passed fb0 N times, we record the instantaneous frequencies f11 and fb1. Then, the mode number can be calculated by:
The calibration error is mainly due to the thermal instability of the free-running TL. To reduce this error, a large value of 936 is chosen for N. Furthermore, we repeat the above procedures 1600 times and calculate the averaged M values using a digital-filter-like method. For example, a 100-time averaging level means taking the average from the 1st to 100th measurement, 2nd to 101st measurement, and so on, until the 1501st to 1600th measurement. The mode number RMS error decreases approximately with the square root of the averaging number, as shown in Fig. 3b. For an averaging level of 1000 times, the mode number error relative to the closest adjacent integer (766,746) is given in Fig. 3c. Since the error is well below 0.5 (<±0.2), M can be precisely determined.
System tuning and instability
To evaluate the frequency instability of the OFS, we use the setup in Fig. 4a to perform an out-of-loop measurement. A full tuning range from 1544 nm (194.1 THz) to 1564 nm (191.6 THz) is achieved for the OFS by applying electrical power to the two microring heaters of the TL. For a tuning range larger than 2 nm, the approximate electrical power required by the two microring heaters can be obtained from a lookup table (see Materials and methods, large-range tuning), and a new calibration procedure is necessary before fine tuning the heaters’ power to set the OFS frequency to the exact target value. Five different wavelengths (1544.46, 1550.69, 1554.93, 1559.41, and 1564.03 nm) are chosen, and the calibrated M values are shown in the first five rows of Fig. 4b. Figure 4b also gives the final OFS output frequencies, fSN, and their corresponding f1 and f3 values in the experiments. By changing the electrical power of the two microring heaters simultaneously, we can continuously tune the OFS frequency relative to a calibrated value by up to ~2 nm (see Materials and methods, middle-range tuning). Using this method, the OFS frequency is decreased by 10.25 GHz (from 1564.03 nm), as given in the last row of Fig. 4b. Figure 4c shows the measured frequency instability (Allan deviation) of the six synthesizer frequencies obtained in Fig. 4b. For all cases, the frequency instability approximately drops inversely proportional to the averaging time τ. Figure 4c shows a frequency instability level of 10−12 at an averaging time of 1 s. At 10 s of averaging time, the frequency instability of each case ranges from 2 × 10−13 to 2 × 10−14 (last column of Fig. 4b).
For fine tuning at the sub-GHz level, the OFS frequency can be simply tuned by changing f3 in the TL-to-comb locking circuit to change the feedback electrical power to the TL phase shifters (see Materials and methods, small-range tuning). The RF synthesizer 3 can be programmed by a PC to generate an arbitrary pattern for the OFS output over time-frequency coordinates. Figure 4d provides an example of the MIT logo obtained from this fast and precise tuning mechanism.
Although the reported TL output power and slope efficiency are not high29, the power is sufficient for the OFS application. In the synthesizer setup, the saturation power of the BPD in Fig. 1 (Thorlabs PDB465C-AC) is 120 µW, which enables a >30 dB signal-to-noise ratio (SNR) for the electronic beat note after the BPD (using a 20 kHz resolution bandwidth on an electronic spectrum analyzer (ESA)) with <100 µW optical power from the TL. After the frequency divider in the TL-to-comb locking circuit (Fig. 2c), this SNR can be further improved to >80 dB, which is more than enough to obtain tight locking.
During the measurement shown in Fig. 3b, c, the repetition rate of the MLL needs to be tuned by ~300 kHz to achieve the value 936 for N. This process takes ~6 s because we need to move a motorized stage in the cavity of the MLL. Therefore, the total calibration time is ~3.3 h with 1000 times of averaging. In the future, by using an integrated MLL31,32, the repetition rate can be tuned by ~1 MHz within 1 ms using integrated heaters, so the overall calibration time can be reduced to <1 s.
In Fig. 4a, the voltage noise floor of the function generator is proportional to the output voltage range. In other words, a high-level output voltage VH usually exhibits a large absolute RMS noise VN, which can be further enhanced through (VH + VN)2, when we convert the voltage noise into the power noise. Thus, the higher the electrical power imposed on the two microring heaters, the more thermo-unstable the OFS is. In Fig. 4c, comparing two wavelengths of 1544.46 nm (M = 776 433) and 1559.41 nm (M = 768 993), the OFS requires much higher electrical power for operation in the first case; therefore, the frequency instability in the first case is almost 10 times higher than that in the latter case. The frequency instability performance can be improved by developing a low-noise voltage/power source with noise filters at the source output. With a better voltage/power source, it is also possible to tune the OFS within the full erbium gain bandwidth, showing good frequency instability performance.
In summary, we have demonstrated an OFS using a fully integrated erbium-doped TL on a silicon photonics platform. The synthesizer can be self-calibrated and supports a 2.5 THz (20 nm) tuning range. The typical frequency instability is 10−13 at a 10 s averaging time. Precise and flexible tuning capability is also demonstrated by generating an MIT logo pattern. Using the techniques in this work and other key components on a silicon photonics platform, including an octave-spanning supercontinuum generator33, second-harmonic generator34, and integrated MLLs31,32, there is great potential to build a completely monolithically integrated low-cost OFS in the near future.
Materials and methods
Effective indices and guided modes in waveguides are simulated using a vector finite-difference 2D eigenmode solver with a discretization of 20 nm. The code is written in MATLAB, and it solves the wave equation of the transverse electric field.
Erbium TL fabrication
The TL is largely fabricated on a 300-mm silicon wafer in a state-of-the-art CMOS foundry at CNSE SUNY. The wafer has etched laser trenches for gain film deposition. After the wafer-scale fabrication, the wafer is diced, and an Al2O3:Er3+ gain film is deposited as a single-step back-end-of-line process at MIT, allowing direct access to the laser design23. The 1.1-µm-thick Al2O3:Er3+ thin film within the laser trench together with the trench sidewall provides the mode confinement for the gain waveguide. The deposition is performed by a reactive co-sputtering process using both aluminum and erbium targets. The substrate temperature during deposition was measured to be 380 °C. Deposition runs with different doping levels reveal an optimum Er3+ doping concentration of 1.5 × 1020 cm−3. Given the same pump power, a lower doping concentration will decrease the lasing power due to lower gain, while too high of a concentration will also result in lower lasing power due to severe ion clustering or quenching35,36. To keep the metal pads open after the Al2O3 thin film deposition process, the metal pads are placed in one area of the layout mask, and this area is covered by a glass plate during the Al2O3 thin film deposition. More details about the area selective deposition can be found in ref. 37.
There are two microring filters in the TL. Each ring has a periodic transmission spectrum (blue and red curves in Fig. 5a), with free spectral ranges (FSRs) of 2.23 and 2.13 nm at room temperature, respectively. This vernier configuration provides a combined FSR of 50 nm within the erbium gain bandwidth, which guarantees a single lasing wavelength of the TL. By changing the electrical power of the integrated heater on top of each ring, the FSR of each ring can be varied slightly; therefore, the TL will lase at a different wavelength where the new transmission spectra of the two rings overlap. For example, in Fig. 5a, the third red curve of ring 1 overlaps with the third blue of ring 2; if we change the voltage on the integrated heater of ring 2 to increase the FSR of ring 2, the fourth red curve may overlap with the fourth blue curve, thus achieving wavelength tuning. Based on this mechanism, a lookup table can be created to record all possible voltage combinations applied to the two ring heaters and their corresponding lasing wavelengths. In practice, with the help of the lookup table, by simply modifying the voltages of the ring heaters, an arbitrary output wavelength of the TL within the erbium gain bandwidth can be provided.
Different from the large-range tuning, if we change the voltages applied to the two ring heaters simultaneously, two specific transmission spectrum curves (e.g., the third red curve and the third blue curve in Fig. 5a) of the two rings can move synchronously; therefore, the combined ring response (magenta-color curves in Fig. 5b–d) can be continuously tuned without wavelength hopping. We can use the cavity transmission response of the TL (orange curves in Fig. 5b–d), which has an FSR of Δf ≈ 2 GHz, to calculate the exact tuning frequency of the combined ring response. To maximize the TL output power, the peak of the combined ring response needs to overlap with one peak of the cavity response, as shown in Fig. 5b. When we synchronously change the voltages on the two ring heaters, the combined ring response can be tuned from the position in Fig. 5b to that in Fig. 5c, d. At the same time, the cavity response FSR, Δf, is also slightly changing (from Δf0 to Δf1 to Δf2) because of the optical length change of the two rings. When the combined ring response is in the middle of two cavity response peaks, as shown in Fig. 5c, the TL can output two longitudinal modes, which can generate four beat notes fd1, frep − fd1, fd2, and frep − fd2 in [0, frep] after beating with an MLL, where frep is the repetition rate of the MLL. Suppose fd1 and fd2 decrease with increasing ring heater voltage; then, the current cavity response FSR, Δfnew, can be calculated by
where Δfest is the estimated FSR value from an earlier calculation or measurement, and the square bracket “[x]int” returns the integer closest to x. In practice, Δf can be initially estimated from the design parameters or measured from the self-beating frequency of the TL by setting the device into a double-longitudinal-mode state with little ring heater power. Then, by synchronously increasing the voltages applied to the two ring heaters and tracing the beat notes between the TL and MLL on an ESA, Δf can be iteratively updated by Eq. 3. Therefore, the frequency of the TL can be accurately tuned across many cavity longitudinal modes. Theoretically, the laser can be tuned over the full erbium gain bandwidth using this middle-range tuning mechanism. However, in practice, we cannot unlimitedly increase the heater voltage without breaking the heater, and if the tuning range is larger than one FSR of the ring response (~2 nm), we can already use the large-range tuning mechanism, so one FSR of the ring response is chosen as the maximum tuning range of the middle-range tuning.
There are two longitudinal-mode phase shifters in the TL. The heaters for the two phase shifters are controlled by the same voltage. By varying this voltage, the frequency of TL can be continuously tuned within one FSR of the cavity transmission response, that is, ~2 GHz.
Jones, D. J. et al. Carrier-envelope phase control of femtosecond mode-locked lasers and direct optical frequency synthesis. Science 288, 635–639 (2000).
Udem, T. et al. Absolute optical frequency measurement of the cesium D 1 line with a mode-locked laser. Phys. Rev. Lett. 82, 3568–3571 (1999).
Madej, A. A., Marmet, L. & Bernard, J. E. Rb atomic absorption line reference for single Sr+ laser cooling systems. Appl. Phys. B. 67, 229–234 (1998).
Swann, W. C. & Newbury, N. R. Frequency-resolved coherent lidar using a femtosecond fiber laser. Opt. Lett. 31, 826–828 (2006).
Trocha, P. et al. Ultrafast optical ranging using microresonator soliton frequency combs. Science 359, 887–891 (2018).
Wu, G. et al. Synthetic wavelength interferometry of an optical frequency comb for absolute distance measurement. Sci. Rep. 8, 4362 (2018).
Castillega, J. et al. Precise measurement of the J = 1 to J = 2 fine structure interval in the 23P state of helium. Phys. Rev. Lett. 84, 4321–4324 (2000).
Thorpe, M. J. et al. Broadband cavity ringdown spectroscopy for sensitive and rapid molecular detection. Science 311, 1595–1599 (2006).
Holzwarth, R. et al. Optical frequency synthesizer for precision spectroscopy. Phys. Rev. Lett. 85, 2264–2267 (2000).
Xue, X. & Weiner, A. M. Microwave photonics connected with microresonator frequency combs. Front. Optoelectron. 9, 238–248 (2016).
Song, M. et al. Reconfigurable and tunable flat-top microwave photonic filters utilizing optical frequency combs. IEEE Photonics Technol. Lett. 23, 1618–1620 (2011).
Wong, J. H. et al. Photonic generation of frequency-tunable microwave signals using an array of uniformly spaced optical combs. J. Lightwave Technol. 30, 3164–3172 (2012).
Spencer, D. T. et al. An optical-frequency synthesizer using integrated photonics. Nature 557, 81–85 (2018).
Arafin, S. et al. Towards chip-scale optical frequency synthesis based on optical heterodyne phase-locked loop. Opt. Express 25, 681–695 (2017).
Arafin, S. et al. Power-efficient Kerr frequency comb based tunable optical source. IEEE Photonics J. 9, 6600814 (2017).
Huang, S. W. et al. A broadband chip-scale optical frequency synthesizer at 2.7 × 10−16 relative uncertainty. Sci. Adv. 2, e1501489 (2016).
Singh, N. et al. Silicon-photonics-based optical frequency synthesizer. In Proc. 2018 Conference on Lasers and Electro-Optics (CLEO) (IEEE, San Jose, 2018).
Magden, E. S. et al. Monolithically-integrated distributed feedback laser compatible with CMOS processing. Opt. Express 25, 18058–18065 (2017).
Li, N. et al. High-power thulium lasers on a silicon photonics platform. Opt. Lett. 42, 1181–1184 (2017).
Purnawirman. et al. Wavelength division multiplexed light source monolithically integrated on a silicon photonics platform. Opt. Lett. 42, 1772–1775 (2017).
Li, N. et al. C-band swept wavelength erbium-doped fiber laser with a high-Q tunable interior-ridge silicon microring cavity. Opt. Express 24, 22741–22748 (2016).
Li, S. et al. Silicon micro-ring tunable laser for coherent optical communication. Opt. Express 24, 6341–6349 (2016).
Li, N. et al. Broadband 2-µm emission on silicon chips: monolithically integrated Holmium lasers. Opt. Express 26, 2220–2230 (2018).
Bernhardi, E. H. et al. Ultra-narrow-linewidth, single-frequency distributed feedback waveguide laser in Al2O3:Er3+ on silicon. Opt. Lett. 35, 2394–2396 (2010).
Purnawirman. et al. Ultra-narrow-linewidth Al2O3:Er3+ lasers with a wavelength-insensitive waveguide design on a wafer-scale silicon nitride platform. Opt. Express 25, 13705–13713 (2017).
Belt, M. et al. Arrayed narrow linewidth erbium-doped waveguide-distributed feedback lasers on an ultra-low-loss silicon-nitride platform. Opt. Lett. 38, 4825–4828 (2013).
Li, N. et al. Athermal synchronization of laser source with WDM filter in a silicon photonics platform. Appl. Phys. Lett. 110, 211105 (2017).
Belt, M. & Blumenthal, D. J. High temperature operation of an integrated erbium-doped DBR laser on an ultra-low-loss Si3N4 platform. In Proc. 2015 Optical Fiber Communications Conference and Exhibition (OFC) (IEEE, Los Angeles, CA, USA, 2015).
Li, N. et al. Monolithically integrated erbium-doped tunable laser on a CMOS-compatible silicon photonics platform. Opt. Express 26, 16200–16211 (2018).
Ma, L. S. et al. A new method to determine the absolute mode number of a mode-locked femtosecond-laser comb used for absolute optical frequency measurements. IEEE J. Sel. Top. Quantum Electron. 9, 1066–1071 (2003).
Kärtner, F. X. et al. Integrated rare-Earth doped mode-locked lasers on a CMOS platform. Baets, R. G. O'Brien, L. & Vivien, L. (eds), In Proc. SPIE 10686, Silicon Photonics: From Fundamental Research to Manufacturing (SPIE, Strasbourg, France, 2018).
Shtyrkova, K. et al. Integrated CMOS-compatible Q-switched mode-locked lasers at 1900nm with an on-chip artificial saturable absorber. Opt. Express 27, 3542–3556 (2019).
Singh, N. et al. Octave-spanning coherent supercontinuum generation in silicon on insulator from 1.06 μm to beyond 2.4 μm. Light Sci. Appl. 7, 17131 (2018).
Timurdogan, E. et al. Electric field-induced second-order nonlinear optical effects in silicon waveguides. Nat. Photonics 11, 200–206 (2017).
Li, N. et al. Self-pulsing in Erbium-doped fiber laser. In Proc. 2015 Optoelectronics Global Conference (OGC) (IEEE, Shenzhen, China, 2015).
Agazzi, L., Wörhoff, K. & Pollnau, M. Energy-transfer-upconversion models, their applicability and breakdown in the presence of spectroscopically distinct Ion classes: a case study in amorphous Al2O3:Er3+. J. Phys. Chem. C 117, 6759–6776 (2013).
Li, N. Rare-Earth-Doped Lasers on Silicon Photonics Platforms. PhD thesis, Harvard Univ., Cambridge (2018).
We would like to acknowledge Professor Federico Capasso for helpful discussions, Gary Riggott, and Kurt Broderick for assistance on erbium-doped thin film deposition, and Helena Zhang and Isaac Chuang for providing the reference frequency comb. We acknowledge financial support by the Defense Advanced Research Projects Agency (DARPA) Direct On-Chip Digital Optical Synthesizer (DODOS) project (HR0011-15-C-0056; program manager: Dr. Gordon Keeler), the Deutsche Forschungsgemeinschaft through Priority Program SPP-1221, DFG 18-17 PACE, and the Deutsches Elektronen Synchrotron—DESY. N.L. was supported by a National Science Scholarship (NSS) from the Agency for Science, Technology and Research (A*STAR), Singapore.
Conflict of interest
The authors declare that they have no conflict of interest.
About this article
Cite this article
Xin, M., Li, N., Singh, N. et al. Optical frequency synthesizer with an integrated erbium tunable laser. Light Sci Appl 8, 122 (2019). https://doi.org/10.1038/s41377-019-0233-z
Towards integrated photonic interposers for processing octave-spanning microresonator frequency combs
Light: Science & Applications (2021)
High-yield, wafer-scale fabrication of ultralow-loss, dispersion-engineered silicon nitride photonic circuits
Nature Communications (2021)
Light: Science & Applications (2020)