Abstract
High-density polyethylene (HDPE)/polystyrene (PS) blends were compatibilized with a (styrene-ethylene/butylene-styrene) tri-block copolymer (SEBS). Both uncompatibilized and compatibilized HDPE/PS 80/20 blend specimens were prepared in a twin-screw extruder followed by injection molding. The effect of SEBS content on the tensile properties of the blends was investigated. It was found that the modulus and yield stress of the HDPE/PS 80/20 blend tend to decrease with increasing SEBS content. However, the elongation at break of the blend improved significantly with the addition of SEBS, indicating the effectiveness of compatibilizing effect of a tri-block copolymer in the immiscible HDPE/PS system. Scanning electron microscopy examination showed that PS phase is fibrillated in the matrix as long fibers, and the SEBS copolymer addition appears to reduce the domain size of PS phase effectively. The fracture toughness of the blends was evaluated by the essential work concept. The result showed that the essential work of the compatibilized HDPE/PS blends also increases with increasing SEBS content.
Similar content being viewed by others
Article PDF
References
C. R. Lindsey, D. R. Paul, and J. W. Barlow, J. Appl. Polym. Sci., 26, 1 (1981).
M. A. Rames and E. P. Collar, J. Polym. Eng., 7, 137 (1987).
J. W. Teh and A. Rudin, Polym. Eng. Sci., 31, 1033 (1991).
R. C. Willemse, A. Pothuma de Boer, J. van Dam, and A. D. Gotsis, Polymer, 39, 5879 (1998).
Y. J. Sun, Richard J.G. Willemse, T. M. Liu, and Warren E. Baker, Polymer, 39, 2201 (1998).
W. E. Baker and M. Saleem, Polymer, 28, 2057 (1987).
Z. Wang, C. M. Chan, S. H. Zhu, and J. R. Shen, Polymer, 39, 6801 (1998).
H. E. Hermes and J. S. Higgins, Polym. Eng. Sci., 38, 847 (1998).
I. Luzinov, K. Xi, C. Pagnoulle, G. Huyanh-Ba, and R. Jerome, Polymer, 40, 2511 (1999).
H. E. Hermes, D. G. Bucknall, J. S. Higgins, and R. L. Scherrenberg, Polymer, 39, 3099 (1998).
S. C. Tjong and S. A. Xu, J. Appl. Polym. Sci., 68, 1099 (1998).
W. M. Barentsen and D. Heikens, Polymer, 14, 579 (1973).
C. E. Loke and D. R. Paul, J. Appl. Polym. Sci., 13, 308 (1983).
R. Fayt, R. Jerome, and Ph. Teyssie, J. Polym. Sci., Polym. Lett. Ed., 24, 25 (1986).
R. Fayt, R. Jerome, and Ph. Teyssie, J. Polym. Sci., Polym. Phys. Ed., 20, 2209 (1982).
R. Fayt, R. Jerome, and Ph. Teyssie, J. Polym. Sci., Polym. Phys. Ed., 33, 801 (1995).
M. C. Schwarz, H. Keskkula, J. W. Barlow, and D. R. Paul, J. Appl. Polym. Sci., 35, 653 (1988).
M. Saleem and W. E. Baker, J. Appl. Polym. Sci., 39, 655 (1990).
H. Feng, J. Tian, and C. Ye, J. Appl. Polym. Sci., 61, 2265 (1996).
T. Li, V. A. Topolkaraev, A. Hiltner, E. Baer, X. Z. Ji, and P. Quirk, J. Polym. Sci., Polym. Phys. Ed., 33, 667 (1995).
S. A. Xu, M. Jiang, and J. S. Shen, Polym. J, 27, 607 (1995).
S. A. Xu, and C. M. Chan, Polym. J., 30, 552 (1998).
M. Taha and V. Frerejean, J. Appl. Polym. Sci., 61, 969 (1996).
N. Mekhilef, B. D. Favis, and P. J. Carreau, J. Polym. Sci., Polym. Phys. Ed., 35, 293 (1997).
M. N. Bureau, H. E. Kadi, J. Denault, and J. I. Dickson, Polym. Eng. Sci., 37, 377 (1997).
M. C. Scharwarz, J. W. Barlow, and D. R. Paul, J. Appl. Polym. Sci., 35, 2053 (1988).
K. B. Broberg, Int. J. Fract. Mech., 4, 11 (1968).
S. Hashemi, Polym. Eng. Sci., 37, 912 (1997).
J. K. Kocsis and T. Czigany, Polymer, 37, 2433 (1996).
J. K. Kocsis and T. Czigany, Polymer, 38, 4587 (1996).
D. E. Mouzakis, F. Stricker, R. Mulhaupt, and J. K. Kocsis, J. Mater. Sci., 33, 2551 (1998).
Y. L. Huang and N. Brown, Polymer, 33, 2989 (1992).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Xu, S., Tjong, S. Effect of Compatibilizer Content on the Tensile Properties and Fracture Toughness of High Density Polyethylene/Polystyrene Blends. Polym J 32, 208–214 (2000). https://doi.org/10.1295/polymj.32.208
Issue Date:
DOI: https://doi.org/10.1295/polymj.32.208