Wireless transfer of information is the basis of modern communication. It includes cellular, WiFi, Bluetooth, and GPS systems, all of which use electromagnetic radio waves with frequencies ranging from typically 100 MHz to a few GHz. However, several long-standing challenges with standard radio-wave wireless transmission still exist, including keeping secure transmission of data from potential compromise. Here, we demonstrate wireless information transfer using a line-of-sight optical architecture with a micromechanical element. In this fundamentally new approach, a laser beam encoded with information impinges on a nonlinear micromechanical resonator located a distance from the laser. The force generated by the radiation pressure of the laser light on the nonlinear micromechanical resonator produces a sideband modulation signal, which carries the precise information encoded in the subtle changes in the radiation pressure. Using this, we demonstrate data and image transfer with one hundred percent fidelity with a single 96-by-270 μm silicon resonator element in an optical frequency band. This mechanical approach relies only on the momentum of the incident photons and is therefore able to use any portion of the optical frequency band—a band that is 10 000 times wider than the radio frequency band. Our line-of-sight architecture using highly scalable micromechanical resonators offers new possibilities in wireless communication. Due to their small size, these resonators can be easily arrayed while maintaining a small form factor to provide redundancy and parallelism.
Micro- and nano-electro-mechanical systems (MEMS and NEMS) resonators are of fundamental and technological interest, with applications ranging from timing in integrated circuits1 to methods in quantum metrology2,3 while operating in their linear regimes. At high-drive amplitudes, these resonators exhibit nonlinear behavior, useful for studying fundamental effects such as stochastic resonance4, parametric amplification and frequency entrainment5, and logic operations6. The nonlinearly-driven resonator can be further modulated with a signal at a separate modulation frequency. In the frequency domain, the response of the nonlinear resonator to the modulation appears as a sideband to the original resonator frequency that carries all the information encoded into the modulation signal. By decoding the sideband signal, the original signal can be retrieved.
Radiation pressure has been used in many applications including cooling micromirrors7,8, affecting optomechanical dynamics in cavities9,10, and has been observed as a form of shot noise11. Existing devices and previous experiments have used optical radiation to perform line-of-sight communication12, typically using photodiodes13,14 as the receiver. While these devices can be small and have the ability to communicate at a high bit rate, they can be highly wavelength dependent15,16 and saturated by the presence of ambient light.
Several long-standing challenges with standard radio-wave wireless transmission still exist, including limited spectrum17; the last-mile problem18 or infrastructure difficulty in the final leg of communication in the network to deliver services to end users; lack of indoor positioning system for accurate location determination19; and keeping secure transmission of data from potential compromise. Here, inspired by the first-ever wireless transmission by Bell20, we demonstrate that the force generated by the radiation pressure of an optical beam21 can be used as the modulation force added to the driven nonlinear resonator. Because our sideband modulation technique requires a nonzero modulation frequency, it is not affected by ambient conditions such as continuous solar radiation. The mechanical nature of this method has the added benefit that it is dependent on the intensity of the carrier and not its wavelength.
Materials and methods
As the intensity of the laser light modulates according to an encoded signal at a frequency fm, the force adding to the nonlinear resonator being driven at a fixed resonator frequency fr generates the sideband. The resonator can be described as a driven nonlinear oscillator with equation of motion22. Here, S(fmt) represents the signal being transmitted by the laser, x is the degree of freedom, m is the effective modal mass, γ is the damping coefficient, k is the effective modal stiffness, k3 is the cubic nonlinear spring constant, Ar is the drive amplitude, and Am is the laser drive coefficient. The laser drive coefficient is proportional to the force exerted by radiation pressure, Frad=(R+1)IlaserA/c, where R is the surface reflectance, Ilaser is the beam intensity, A is the resonator’s effective mode area, and c is the speed of light. The steady-state response was numerically shown to approximately obey the relation where n is an integer. The constants cr, cm, and c3(n) represent the sizes of the frequency responses. To verify Equation (2), we numerically solved Equation (1) and performed a fast Fourier transform on the results to obtain the frequency spectrum. Results are in the Supplementary Information.
A schematic diagram of our setup is shown in Figure 1a. A green laser diode (LD) that is normally incident on the driven resonator provides the additional small signal using a pulse train with a modulation frequency between 1 and 5 kHz. The laser is modulated in amplitude and frequency using a waveform generator which was connected to the modulation port of the laser’s driver. Several different waveforms, including sine waves and pulse trains, were tested, and all produced similar results. The MEMS resonator, shown in Figure 1b, is a 96-by-270-μm rectangular plate resonator that is suspended by sixteen 15-by-3-μm legs. From bottom to top layer, it is constructed from 5-μm-thick silicon and 1-μm-thick silicon dioxide structural layers, a 300-nm-thick molybdenum layer used for grounding, a 1-μm-thick aluminum nitride (AlN) piezoelectric layer for signal transduction, and 300-nm-thick inter-digitated molybdenum electrodes for actuation and detection. Direct actuation and detection can be performed via a direct electrical connection to the marked electrodes in Figure 1b. The other four electrodes, marked “G”, are used as ground references. The resonators are directly actuated via the inverse piezoelectric effect, and the response is measured using the direct piezoelectric effect. Applying a voltage to one of the transduction electrodes at some frequency causes a time-varying stress within the resonator. Likewise, stresses produce electric fields within the AlN which can be detected at the other transduction electrode. The device is symmetric, so either signal electrode can be used for either purpose.
To characterize the resonator, the spectrum was measured (with the laser turned off) by sweeping the signal generator in the frequency range 120–121 MHz for a range of powers. The response of the resonator is measured using a swept spectrum analyzer. A subset of these measurements is shown in Figure 1c. Using COMSOL, we numerically identified the mode to be a high-order Lamb wave mode with its largest deflections at the locations of each of the electrode pads (details in the Supplementary Information). At low powers, the resonator has a linear, Lorentzian frequency response. With increasing power, the response becomes pronouncedly nonlinear, which is evident from the skewing of the resonance peak and the onset of hysteretic behavior. This resonator’s most sensitive resonance is at 120.4 MHz and has a quality factor of 485. For the remainder of the experiment, we directly drive the resonator at this frequency using a power of 19 dBm, providing a 10 μN effective force as estimated using a first-order calculation and verified numerically.
Next, the LD, with wavelength 520 nm, was turned on. Using the optical beam and resonator properties, we estimate the radiation force to be near 0.72 pN, orders of magnitude smaller than the resonator’s driving signal (calculation details are in the Supplementary Information). With the laser modulation added, the presence of equally-spaced sidebands was observed, as shown in Figure 2a. The first-order upper sideband, located at frequency fr+fm, was then characterized by driving the resonator in the range 120–121 MHz and measuring the sideband amplitude. The laser was modulated with a 50%-duty-cycle pulse train at frequency 3 kHz. Figure 2b shows the size of the sideband and the downsweep response of the resonator when driven at 19 dBm. As expected, the sideband amplitude is related to the size of the resonator’s peak response with the largest sideband amplitude appearing when the driving frequency is near the peak response frequency of the resonator. Further device characterizations are in the Supplementary Information.
Using these sidebands, wireless data transmission can be achieved using several different methods. First, we transmitted using amplitude modulation (AM) at a single modulation frequency using a 50% duty-cycle pulse train. To transmit a “1”, the pulse train has a large amplitude; to transmit a “0”, it has a smaller or zero amplitude. Figure 3a shows a portion of the AM transmission of the string “Hello world!”. The purple line represents the logic levels that were transmitted, and the blue line indicates the amplitude of the measured sideband. Both data sets are normalized such that the minimum measurement is 0 and the maximum is 1. In this case, the “1’s” are transmitted using a 119.6 mA peak current to the LD and the “0’s” are transmitted by providing no current.
After “Hello world!” was successfully transmitted several times, we transmitted a larger file—a 100-by-100 pixel monochrome version of the iconic image of Einstein shown in the top panel of Figure 3b. White pixels were represented by “1’s” and transmitted using a 140 mA pulse train; black pixels were represented by “0’s” and transmitted using a 59.6 mA pulse train. The results of this transmission, which contained 155 errors, are shown in Figure 3b. We performed a statistical analysis of the data received and found that the amplitudes of “0” and “1” data points obey Gaussian distributions with standard deviations 0.12 and 0.087, respectively, as illustrated in Figure 3c. From these distributions, we obtain an average bit error rate (BER) of 1 error per 86.9 bits.
An alternate method of transmitting data used was frequency modulation (FM). We again used a 50%-duty-cycle pulse train that varied between a maximum current of 140 mA and a minimum current of 0 mA; however, in this case, the pulse train was not turned off at any point during transmission. Instead, data was transmitted by making minor adjustments to the frequency of the pulses in order to change the frequency at which the sideband occurs. By assigning each sideband frequency a “value”, non-binary digital data was transmitted.
In Figure 4a we present a ‘hexadecimal’ data transmission. For the data shown, laser modulation of 1 kHz (f0) represents a “0” and successive digits are spaced in 50 Hz (Δf) increments. A “−1” (for our parameters, laser modulation at 950 Hz) was transmitted between digits to aid in processing the received data. The largest frequency measured between two “−1’s” was stored, and the function digit=(fstored−f0)/ Δf was rounded to the nearest integer to decode the signal. Figure 4b shows the result of a transmission of the same image of Einstein as before which, unlike our AM transmission, contains no errors. For this transmission, groups of four bits were encoded into a single hexadecimal digit.
Next, we transmitted a series of random hexadecimal digits to estimate the BER. As shown in Figure 4c, the distributions of sideband frequencies for each hexadecimal digit approximately obeyed Gaussian distributions with standard deviations averaging 5.6 Hz. For FM transmission, we estimate an average BER of 1 error per 56 320 data packets.
While the specific equipment used in our proof-of-concept demonstration is not yet suitable for practical applications, alternate arrangements including a combination of more powerful lasers, using optics designed to focus beam at resonator location, and arraying resonators may be effective in producing higher signal-to-noise ratios and bitrates. In addition, our demonstration was not designed for high speed applications, as its speed was severely limited by the speed of the spectrum analyzer. In principle, this method can be used for much higher bitrates than demonstrated here by using high-frequency, low-Q resonators. Reducing Q also has the benefit of increasing the usable bandwidth, but reduces the signal size, so the resonator must be carefully designed for its specific application. Some nanomechanical resonators have been shown to have frequencies on the order of 10 GHz (Ref. 23), so the maximum feasible bit rate, which is limited to approximately f0/Q in an open-loop configuration, can be hundreds of MHz to several GHz. Of course, the modulation frequency must be larger than the bitrate in order to consistently produce measurable sidebands.
There are additional practical limitations to this method, but many can be easily addressed. For one, distance, beam intensity, resonator angle relative to beam, and other factors can cause fluctuations in the intensity of the sideband which can corrupt data transmitted via AM. We experienced this behavior during our experiment as well; sideband amplitudes fluctuate somewhat randomly, but their frequencies are highly predictable. For this reason and because of the much more favorable BER, transmission should be performed using FM. Optimal sideband frequencies should also be determined before implementation; low frequencies are susceptible to noise from sources such as ambient vibration and electrical signals. Sideband frequencies should also be chosen to avoid noise from known sources of mechanical vibrations.
In addition to successful demonstration of wireless data transmission, we performed control experiments to verify that the sideband response and its dependence on the modulation signal is indeed due to the modulation in the radiation pressure exerted on the resonator. To this end, blocking the resonator from the laser light produced no sideband signal. Further, we found that the sideband size is proportional to the optical power of the laser as predicted for excitation by radiation pressure. To verify that the resonator was not being actuated by photothermal effects24,25, temperature change due to radiation was monitored using the shift in the resonance frequency. As discussed in Supplementary Information, though the resonance frequency of the resonator shifts with heating, it does not produce a sideband even when heating is modulated in a similar manner as the laser. While the resonance frequency changes with temperature, the frequency of the sideband is related to the carrier frequency, which is externally generated and not a function of temperature. The main effect of temperature changes is that the shifting of the resonance can affect the amplitude of the sideband. Since the sideband amplitude is related to the resonator’s response at the carrier frequency, a feedback loop should be implemented in practice to adjust the resonator driving frequency with a measured temperature. To further verify that the sideband is generated due to nonlinear mixing, the resonator was driven in the linear regime, which produced no sideband, reconfirming Figure 2.
In conclusion, we demonstrated successful wireless transmission of data using the force produced by a phenomenon as weak as radiation pressure. Depending on the modulation, this method can be used to transmit digital or analog information. Applying techniques in signal demodulation and arraying resonators to increase the signal size and fidelity, our methods can be adapted for use in technologies ranging from signal transduction in fiber optic communications systems to virtually undetectable free-space communications with satellites, as can be done with similar techologies17,18,19. Our method has the added advantage being a purely mechanical effect and hence is not strongly wavelength-dependent as photodiodes are known to be.
We thank Dr. Carl Boone for helpful discussions and support.