Abstract
As an intrinsically direct current device, quantum-dot LED cannot be directly driven by household alternating current electricity. Thus, a driver circuit is required, which increases the complexity and cost. Here, by using a transparent and conductive indium-zinc-oxide as an intermediate electrode, we develop a tandem quantum-dot LED that can be operated at both negative and positive alternating current cycles with an external quantum efficiency of 20.09% and 21.15%, respectively. Furthermore, by connecting multiple tandem devices in series, the panel can be directly driven by household alternating current electricity without the need for complicated back-end circuits. Under 220 V/50 Hz driving, the red plug-and-play panel demonstrates a power efficiency of 15.70 lm W−1 and a tunable brightness of up to 25,834 cd m−2. The developed plug-and-play quantum-dot LED panel could enable the production of cost-effective, compact, efficient, and stable solid-state light sources that can be directly powered by household alternating current electricity.
Similar content being viewed by others
Introduction
Light-emitting diodes (LEDs) have become the mainstream lighting technology due to their advantages of high efficiency, exceptional longevity, solid state, and environmental safety, which fulfills the global demand for energy efficiency and environmental sustainability1,2,3,4. As a semiconductor pn diode, LED can only be operated under the driving of a low-voltage direct current (DC) source. Due to the unidirectional and continuous charge injection, the charges as well as the Joule heat can accumulate within the devices, thereby reducing the operational stability of LEDs5,6. Moreover, the global electricity supply is dominated by high-voltage alternating current (AC), which cannot be directly used by numerous household appliances like LED lamps. Therefore, when LEDs are driven by household electricity, an additional AC-DC converter is required as an intermediary to convert high-voltage AC into low-voltage DC. Typical AC-DC converters consist of a transformer to step down the mains voltage and a rectification circuit to rectify the AC input (Supplementary Fig. 1a). Although most AC-DC converters can achieve conversion efficiencies of over 90%7,8,9,10,11, energy losses remain during the conversion process. In addition, to tune the brightness of LEDs, a dedicated driver circuit should be used to regulate the DC power and supply the ideal current to the LEDs (Supplementary Fig. 1b)12,13. The reliability of driver circuits can impact the durability of LED lamps. As a result, introducing the AC-DC converters and DC drivers not only incurs additional costs (accounting for approximately 17% of the entire LED lamp cost)14 but also increases power consumption and reduces the robustness of LED lamps. Therefore, it is highly desirable to develop LEDs or electroluminescence (EL) devices that can be directly driven by household 110 V/220 V at 50 Hz/60 Hz without complicated back-end electronics.
Over the past few decades, several AC-driven EL (AC-EL) devices have been demonstrated15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50. Typical AC-EL devices consist of a phosphor emissive layer sandwiched between two insulating layers (Supplementary Fig. 2a)15,16,17,18,19,20,21,22,23,24,25,26. The use of insulating layers blocks the injection of external charge carriers and thus there is no DC current flowing through the devices. The device functions as a capacitor and under the driving of a high AC electric field, the electrons, internally generated from the trapped sites, can tunnel into the emissive layer. After gaining sufficient kinetic energy, the electrons impact the luminescent centers, thereby leading to the generation of excitons and light emission15,16,17,18. Due to the inability to externally inject electrons from the electrodes, these devices demonstrate notably low levels of brightness and efficiency, thus limiting their suitability for applications in lighting and displays15,16,17,18,19,20,21,22,23,24. In efforts to enhance their performance, AC-EL devices featuring a single insulating layer have been devised (Supplementary Fig. 2b)27,28,29,30,31,32,33,34,35,36,37,38,39,40. In this structure, during the positive half cycles of AC driving, one type of charge carrier is directly injected from the external electrodes into the emissive layer; by recombining with the other type of charge carriers that are internally generated, efficient light emission can be observed. However, during the negative half cycles of AC driving, the injected charge carriers are released from the devices, and thus there is no light emission. Since light emission occurs only in a half cycle of driving, such AC devices are less efficient than DC devices. Moreover, due to the capacitive nature of the devices, both types of AC devices exhibit frequency-dependent EL performance28,29,30,31,32,33,34, and the best performance is usually achieved at a high frequency of several kHz18,19,20,21,22,23,27,28,29,30,31,32,33,34,35,36,37,38,39,40, making them challenging to be compatible with a low frequency (50 Hz/60 Hz) of standard household AC electricity.
Recently, an AC-EL unit that can be operated at 50 Hz/60 Hz has been proposed51,52,53,54,55,56,57,58,59,60. Such a unit consists of two side-by-side DC devices (Supplementary Fig. 2c)54,55,56,57,58,59. By electrically shorting the top electrodes of two devices, and connecting the bottom coplanar electrodes to an AC source, the two devices can be turned on alternately. From the circuitry perspective, such an AC-EL unit is obtained by serially connecting a forward device and an inverted device. When the forward device is turned on, the inverted device is switched off and functions as a resistor. Due to the presence of resistors, the EL efficiency is relatively low56,57,58. In addition, the AC-EL unit can only be operated at low voltage, which cannot be directly integrated into 110 V/220 V standard household electricity. As summarized in Supplementary Fig. 3 and Supplementary Table 1, the reported AC-EL devices driven by high AC voltage exhibit lower performance (brightness and power efficiency) than that of the DC devices, and thus far, there is no AC-EL device that can be directly driven by 110 V/220 V at 50 Hz/60 Hz household electricity with high efficiency and long lifetime.
In this contribution, we present tandem quantum-dot LEDs (QLEDs) capable of direct operation using standard household electricity of 110 V/220 V at 50 Hz/60 Hz. The QLEDs exhibit remarkable features, including tunable emission color, high color saturation, elevated brightness levels, and simple solution processability. Consequently, they have garnered significant attention as prospective contenders for both light sources and displays in recent research endeavors61,62,63,64,65,66,67. Our developed tandem device consists of two vertically stacking QLEDs that are connected by a transparent and conductive indium-zinc-oxide (IZO) intermediate electrode. By shorting the bottom and top electrodes as a common electrode, and extracting the IZO intermediate electrode as a counter electrode, two QLEDs with opposite polarity are connected in parallel. The resulting tandem device can be operated at both negative and positive cycles of the AC voltage with a high external quantum efficiency (EQE) of 20.09% and 21.15%, respectively. Under AC driving, the accumulated charges and Joule heat can be effectively reduced, and thus the lifetime of QLEDs is significantly prolonged. Furthermore, by connecting multiple tandem QLEDs in series, a household AC electricity plug-and-play QLED (PnP-QLED) light source is obtained. Under 220 V/50 Hz driving, the (PnP-QLED)30 demonstrates a high power efficiency (PE) of 15.70 lm W−1 and a tunable brightness of up to 25,834 cd m−2. The developed (PnP-QLED)n (n is the number of PnP-QLEDs used for connection) could enable the production of low-cost, compact, efficient, and stable solid-state light sources that can be directly powered by household AC power.
Results
Principle and performance of tandem QLEDs
As schematically shown in Fig. 1a, our proposed tandem device consists of a bottom (B) QLED and a top (T) QLED that are vertically stacked and connected by a transparent and conductive IZO intermediate electrode. The use of IZO plays a key role, as it enables the tandem device to operate in both DC and AC modes. Under the DC mode, the tandem device is denoted as S-QLED, where both B-QLED and T-QLED are connected in series. Driven by a DC source, both B-QLED and T-QLED are turned on simultaneously. Under the AC mode, the tandem device is denoted as AC-QLED, where the top Al of T-QLED and bottom indium-tin-oxide (ITO) of B-QLED are electrically shorted to serve as a common electrode, while the IZO is extracted as a counter electrode. In this configuration, the B-QLED and T-QLED with opposite polarity are connected in parallel, as schematically shown in Fig. 1a. Compared to the reported AC-EL devices, the advantages of our AC-QLED are as follows. Firstly, our AC-QLEDs ensure continuous light emission. Under the driving of an AC source, the B-QLED and T-QLED are alternately turned on, thereby allowing light emission to be continuously observed in either the positive or negative cycles of AC voltage. Secondly, our devices show high performance and longer lifetime. Even driven by an AC source, the QLEDs inherently operate in DC mode when they are turned on, allowing them to achieve high brightness and efficiency. Besides, a longer lifetime is expected due to the introduction of a negative bias when they are switched off. Lastly, our QLEDs maintain superior performance even at low frequency of 50 Hz/60 Hz, owing to the fact that they are not capacitive devices. The above advantages make our tandem QLED a very promising candidate for realizing efficient household AC electricity plug-and-play (PnP) light sources.
The optical performance of the devices can be simulated by using a dipole radiation model (Supplementary Fig. 4)68,69,70,71. The simulation methods and refractive index (Supplementary Figs. 4–6) used for simulation are detailed in the Supplementary Simulation Method. To validate the accuracy of the simulation, we compare the simulated EQE/γ with the measured EQE, where γ is the electrical efficiency and is determined by the ratio of generated excitons to the injected hole-electron pairs. As shown in Supplementary Fig. 7h, the trend of the EQE/γ of the QLED is in good agreement with the measured EQE, confirming the accuracy and reliability of our simulated methods. Optically, the tandem device can be modeled as two vertically stacked Fabry-Pérot resonant cavities, as shown in Fig. 1b. The length of one cavity is affected by the length of another cavity. Therefore, to achieve constructive wide-angle interference and enhance the light outcoupling efficiencies (OCEs) of both B-QLED and T-QLED, the length of both cavities should be simultaneously optimized. By tuning the thickness of the bottom ITO and ZnMgO (ZMO_B), it is possible to optimize the OCEs of both B-QLED and T-QLED simultaneously without compromising their electrical performance. As shown in Supplementary Fig. 8, with 80 nm ITO and 110 nm ZMO_B, both B-QLED and T-QLED exhibit the highest OCEs of 29.3% and 30.5%, respectively. Similarly, the OCEs of both B-QLED and T-QLED are influenced by the thickness of the intermediate IZO electrode and the top ZnMgO (ZMO_T) layer. As shown in Supplementary Fig. 9 and Fig. 1c, the optimal thicknesses of IZO and ZMO_T are 30 nm and 90 nm, respectively, which result in the highest OCEs of over 30% for both B-QLED and T-QLED and over 61.5% for the S-QLED.
Guided by the simulation results, tandem devices with optimal thickness were fabricated. The B-QLED (with an optimal structure of glass/ITO 80 nm/ZMO_B 110 nm/QD 20 nm/CBP 50 nm/MoO3 10 nm/IZO 30 nm) was prepared first, followed by spin-casting the ZMO_T on top of the IZO. During the fabrication of the ZMO_T (Supplementary Fig. 10a), the solvent ethanol can penetrate the B-QLED and cause damage to the organic layers (Supplementary Fig. 10c), leading to the cracking of the IZO (Fig. 1d and Supplementary Fig. 10e). To tackle this issue, a dynamic spin-casting method (Supplementary Fig. 10b) was developed to deposit the ZMO_T, which can effectively mitigate the solvent-induced damage and thereby maintain the integrity of the IZO (Fig. 1e, Supplementary Fig. 10d, f). The developed fabrication processes (Supplementary Fig. 11) allow us to realize damage-free tandem devices, as evidenced by the uniform light emission from B-QLED, T-QLED, and S-QLED, respectively (Fig. 1f–h).
By extracting the IZO as an independent electrode, the performance of both B-QLED and T-QLED can be individually evaluated. As shown in Fig. 1i and Table 1, with an optimal IZO thickness of 30 nm, the B-QLED and T-QLED exhibit an EQE of 20.09% and 21.51%, respectively, which is very close to that of the single device (Supplementary Fig. 7), indicating that the optical and electrical performances of the tandem device are fully optimized. As shown in Fig. 1i, j, and Supplementary Fig. 12, the current density-voltage-luminance (J-V-L) and EQE-J characteristics of the S-QLED (tandem device operates in DC mode) are perfectly equal to the summation of those of B-QLED and T-QLED, indicating there are no optical or electrical performance losses in the tandem device. Such a result also implies that both B-QLED and T-QLED are effectively connected by the IZO electrode. The key performances of the devices are summarized in Table 1.
Figure 1k shows the photos of a tandem device that was operated in AC mode. To distinguish the emission color, a red B-QLED and a green T-QLED were used. Under the driving of a positive voltage, only the green T-QLED is turned on, while under the driving of a negative voltage, only the red B-QLED is activated. Therefore, driven by an AC source, both B-QLED and T-QLED are alternately turned on, as demonstrated in Supplementary Movie 1. The results indicate that our tandem device can perfectly operate in AC mode.
Performance of alternating current-driven QLEDs
The equivalent circuit of the tandem QLED operated in AC mode is shown in Fig. 2a, b. In the positive driving cycles (Fig. 2a), the T-QLED is turned on, while the B-QLED is switched off. Thus, the total current density (JF) in positive driving cycles is equal to the summation of forward current density of T-QLED (JF_T) and the reverse current density of B-QLED (JR_B). A small JR_B is preferred since it does not contribute to photon generation. By individually driving the T-QLED and B-QLED, the JF_T and JR_B can be measured. As shown in Fig. 2c, the JR_B is several orders of magnitude lower than the JF_T, and thus the total current JF is mainly determined by JF_T. As a result, the EQE of AC-QLED in the positive driving cycles is almost equal to that of T-QLED, especially in the high current range where the JR_B can be neglected. Similar results are also obtained when the AC-QLED operates in the negative driving cycles (Fig. 2b, c).
At low current or low brightness levels, the reverse current cannot be neglected, as it greatly affects the efficiency losses of the AC-QLED. As shown in Fig. 2d, it can be observed that the efficiency losses of AC-QLED under positive and negative driving cycles are not equal. Due to the rougher surface induced by the thick bottom layers, the reverse current density JR_T (from the T-QLED) during the negative driving cycles is much higher than the reverse current density JR_B (from the B-QLED) during the positive driving cycles, as illustrated in Fig. 2c. Consequently, under negative driving cycles, the energy losses in the AC-QLED are higher compared to those under negative driving cycles. However, for high currents or high brightness situations, because the forward current is significantly higher than the reverse current, the impact of the reverse current on the efficiency of AC-QLED becomes negligible. Due to the low reverse current of the diode, the reversely biased devices do not incur appreciable energy losses to the AC-QLED. For example, at a brightness of 1000 cd m−2, the AC-QLED exhibits a PE of 26.46 lm W−1 in positive driving cycles and 20.99 lm W−1 in negative driving cycles (Supplementary Fig. 13), which is close to 26.59 lm W−1 and 21.17 lm W−1 of the T-QLED and B-QLED, respectively. As illustrated in Supplementary Fig. 14, the energy loss of the AC-QLED accounts for less than 1% under high voltage or luminance, significantly lower than the energy loss in switching power supplies (AC-DC converters and DC-DC driver circuits), which typically ranges from 10% to 20%9,10,11,12,13. Consequently, driven by a 50 Hz square wave AC voltage, the red AC-QLED exhibits an average PE of 23.16 lm W−1 at an average brightness of 1000 cd m−2, which are the best ever reported for AC-EL devices, as compared in Supplementary Table 1 and Supplementary Fig. 3.
Although the efficiency of AC-QLED is almost the same as that of QLED driven by a DC source, its lifetime is effectively prolonged. During forward driving, the charge carriers are continuously injected and accumulated in the devices, leading to the rise of the driving voltage, the quenching of light emission, and eventually the degradation of devices49. By applying a negative bias, the accumulated charges can be effectively released, resulting in a partial recovery of the luminescence, as demonstrated in Supplementary Fig. 15. Therefore, by operating the tandem device in AC mode, the T95 lifetime (time for the brightness decreasing to 95% of its initial value of 10,000 cd m−2) reaches 216 h, which is almost two times longer than 110 h of the tandem device operated in DC mode, as shown in Fig. 2e–g.
The basic plug-and-play QLED
The developed AC-QLED can be operated over a wide frequency range of several Hz~MHz. However, its driving voltage is relatively low, making it difficult to directly integrate into high-voltage AC electricity. By connecting many AC-QLEDs in series, the driving voltage can be multiplied. The resulting light source can be regarded as a PnP device as it is compatible with any AC voltage and frequency. A basic PnP-QLED consists of two side-by-side AC-QLEDs that are connected in series by the intermediate IZO electrode, as shown in Fig. 3a. The fabrication processes of the PnP devices are shown in Supplementary Fig. 16. In the positive driving cycles, the T-QLED from the first tandem device and the B-QLED from the second tandem device are turned on, while in the negative driving cycles, the B-QLED from the first tandem device and the T-QLED from the second tandem device are activated, as shown in Fig. 3b and demonstrated in Supplementary Movie 2. No matter what the driving cycles are, light emission always originates from a T-QLED and a B-QLED, thereby ensuring that the PnP-QLED outputs a constant brightness throughout the entire AC driving. This addresses the issue of unequal efficiency between B-QLED and T-QLED during AC driving. The optical performance of PnP-QLED is close to that of S-QLED because for these two types of devices, light emission always originates from both T-QLED and B-QLED. However, the electrical performance is different. As shown in Fig. 3c, compared to S-QLED, the PnP-QLED shows a higher leakage current (region A), which is due to the presence of reverse current in the parallel circuit. Fortunately, the reverse current is relatively small and only slightly affects the EQE in the low brightness region (Fig. 3d). As the driving voltage is increased, the PnP-QLED exhibits lower current (region B) and luminance, which is induced by the resistance of IZO wire. By calculating the power difference (ΔP) between the PnP-QLEDs with a 0.2 mm and a 0.5 mm long IZO wire (Supplementary Fig. 17), and fitting ΔP with \(\triangle P{=I}^{2}{R}_{{{\mbox{IZO}}}}\), where I is the current in the PnP-QLED and RIZO is the resistance of IZO wire, the RIZO can be calculated as 0.2 Ω μm−1. Despite the presence of RIZO and reverse current, the PnP-QLED still exhibits a peak PE of 20.46 lm W−1, which is slightly lower than 22.66 lm W−1 of the S-QLED, as shown in Fig. 3e. By replacing the IZO with a more conductive wire, the PE can be further improved. Furthermore, as shown in Supplementary Fig. 18, the T95 lifetime (initial average luminance of 10,020 cd m−2) of the PnP-QLED under sinusoidal AC driving reaches 160 h, which is 1.5-fold longer than that of the PnP-QLED driven by a DC source. The results confirm that the PnP-QLED is capable of achieving both high efficiency and prolonged lifetime when operated under household AC electricity.
Household alternating electricity-driven plug-and-play QLED
Using the basic PnP-QLED as a building block, a series of light sources that can be directly plugged into household AC electricity can be realized. Figure 4a shows the schematic circuit diagram of several PnP-QLEDs that are connected in series. The resulting light source is labeled as (PnP-QLED)n, where n denotes the number of PnP-QLEDs used for connection. Except for the need to pattern the bottom ITO, the intermediate IZO, and the top Al electrodes, all other fabrication processes are the same as for regular QLEDs, as shown in Supplementary Fig. 19a. The PnP-QLEDs are connected by metallic Al (Supplementary Fig. 19b), which is highly conductive, and thus the power consumption caused by Al wires is negligible. Hence, no matter how many PnP-QLEDs are connected, the PE of (PnP-QLED)n is the same as that of the basic PnP-QLED. By varying the n, the operational voltage of (PnP-QLED)n can be tuned to match arbitrary AC voltage levels.
To demonstrate that the (PnP-QLED)n can be directly driven by household 220 V/50 Hz AC electricity, the n is varied. To realize the maximum PE, an ideal n should be used. The average voltage dropped across each PnP-QLED is 220/n V; by finding the corresponding PE at that voltage from the PE-V curve of PnP-QLED (Supplementary Fig. 20), the PE of (PnP-QLED)n can be obtained. The calculated PE as a function of n is shown in Fig. 4b. With an ideal n = 37 or 38, a maximum PE of 20.46 lm W−1 can be achieved. However, due to sample size limitations, we could only connect a maximum of 30 PnP-QLEDs. With our custom measurement setup (Supplementary Fig. 21), the AC voltage, current, and luminance of the (PnP-QLED)n can be measured (Supplementary Figs. 22–25d). Supplementary Fig. 22d presents the AC voltage and current of the (PnP-QLED)30 under 220 V/50 Hz driving. The average current (Iavg) and power (Pavg) consumed of the (PnP-QLED)n can be calculated by:
where T is the period of AC driving, VRMS(t) and IRMS(t) are the root mean square voltage and current. Additionally, a photodiode was used to measure the average radiated luminous flux (lumens) of (PnP-QLED)n over multiple periods. With the Iavg, Pavg, and lumens as the inputs, the PE, EQE, and CE of the (PnP-QLED)n can be obtained. As shown in Fig. 4b, by increasing the n from 26 to 30, the PE is gradually enhanced from 8.03 lm W−1 to 12.70 lm W−1. Such a trend is consistent with the calculation. The lower PE is due to the poor uniformity induced by the large size (over 1 cm2) of samples. By improving the laboratory fabrication conditions, a theoretically high PE of 20.46 lm W−1, which is similar to that of PnP-QLED, can be obtained.
Figure 4c shows the PE of (PnP-QLED)30 as a function of AC voltage. The PE is gradually decreased as the AC voltage is increased, which is consistent with the calculation and follows the same trend as conventional QLED. The PE, CE, and EQE of the (PnP-QLED)26~30 are also shown in Supplementary Fig. 25a–c. By varying the AC voltage, the brightness can be effectively tuned from 1000 cd m−2 to over 25,834 cd m−2, as shown in Supplementary Fig. 22d. The (PnP-QLED)30 outputs very uniform light emission and gradually enhanced brightness when the AC voltage is increased, as demonstrated in Fig. 4d and Supplementary Movie 3. The AC voltage can be simply tuned by changing the number of coils in the AC transformer (Supplementary Fig. 26), thereby providing an easy and cost-effective way for tuning the brightness of (PnP-QLED)n. This approach not only reduces the AC-DC circuit but also eliminates the complex current regulation circuit that is used to tune the brightness of DC LEDs. As a demonstration, we show that our developed red (n = 30), yellow (n = 28), and white (n = 26) (PnP-QLED)n can be directly plugged into a household 220 V/50 Hz power supply without needing any accessories, as shown in Fig. 4e and Supplementary Movie 4.
To investigate whether there is a luminance flickering that is commonly observed in AC-driven light sources such as incandescent bulbs or fluorescent lamps, the time-resolved electroluminescence (TrEL) of (PnP-QLED)30 under household AC electricity driving was measured. As shown in Fig. 4f, the driving voltage varies in a sinusoidal manner, and at low driving voltage, the device cannot be switched on and therefore there is no light output. For example, for the (PnP-QLED)30 driven by a 220 V household power supply, there is 1.56 ms in an AC cycle (20 ms) that the device is in a dark state. Because the light output during an AC cycle is not continuous and steady, the human eye perceives luminance flickering. The luminance flickering can be mitigated by improving the continuity of light output. By reducing the value of n, the turn-on voltage of (PnP-QLED)n can be reduced, and thus the duration of the dark period can be decreased. For example, when the n decreases from 30 to 16, the dark period of (PnP-QLED)n effectively decreases from 1.56 ms to 0.38 ms (Supplementary Fig. 27a), thereby leading to the suppression of luminance flickering. To achieve a more stable light output and further reduce luminance flickering, we connected two (PnP-QLED)30 devices in parallel and modified the phase of the AC electricity for one (PnP-QLED)30 device, as schematically illustrated in Supplementary Fig. 27b. The modification of the phase of the AC electricity can simply be achieved by using a capacitive delayer. By delaying 5 ms, the phase of the AC is altered by 90°. Under household AC electricity driving, the first (PnP-QLED)30 is rapidly powered on, while the second (PnP-QLED)30 is powered on 5 ms later. Due to the 90° phase difference of the AC driving, the EL of both (PnP-QLED)30 is different at a given time. For example, when the first (PnP-QLED)30 exhibit the maximum EL, the second (PnP-QLED)30 exhibit the minimum (dark) EL, as shown in Fig. 4f. Therefore, the total EL from both (PnP-QLED)30 is relatively stable and continuous, thus significantly reducing the luminance flickering.
Discussion
In summary, we have developed an innovative tandem QLED that can be directly driven by household AC electricity. By using the IZO as an intermediate electrode to vertically connect the B-QLED and T-QLED, the resulting tandem QLED can be operated under DC or AC mode. Under DC mode, the tandem QLED exhibits a high EQE of 42.16%. Under AC mode, the B-QLED and T-QLED are alternately turned on with an EQE of 20.09% and 21.51%, respectively. Compared to conventional AC-EL devices, our AC-QLEDs exhibit continuous light emission throughout the entire driving cycle. In addition, they can be operated over a wide frequency range (several Hz-MHz) while maintaining high performance similar to that of S-QLEDs. Moreover, they demonstrate an extended T95 at 10,000 cd m−2 lifetime of 216 h, which is two times longer than that of S-QLEDs. With the developed AC-QLED as a basic building block, (PnP-QLED)n with 2n AC-QLEDs connected in series can be constructed. By varying the number of AC-QLEDs, the operational voltage of (PnP-QLED)n can be tuned to match arbitrary AC voltage levels. We demonstrate that our developed (PnP-QLED)n can be directly plugged into a household 220 V/50 Hz power socket. By varying the AC voltage, the brightness can be tuned from 1000 cd m−2 to over 25,834 cd m−2. The developed (PnP-QLED)n can be directly driven by arbitrary AC voltage and frequency without the need for complex back-end driver circuitry and thus could enable the production of low-cost, compact, efficient, and stable solid-state light sources for various applications.
Methods
Materials
All materials used in this study were commercially available. ITO glass with a sheet resistance of 20 Ω sq−1 and a thickness of 80 nm was obtained from Wuhu Jinghui Electronic Technology Co., Ltd., while an IZO target consisting of 90 wt.% In2O3 and 10 wt.% ZnO was acquired from Hebei Gaocheng New Materials Technology Co., Ltd. Nanoparticles of ZnMgO (ZMO) were obtained from Guangdong Poly OptoElectronics Co., Ltd. The chemical 4,4′-Bis(9-carbazolyl)−1,1′-biphenyl (CBP) was acquired from Luminescence Technology Corp. Molybdenum trioxide (MoO3) and octane were procured from Aladdin Industrial Corp. Absolute ethanol was sourced from Shanghai LingFeng Chemical Reagent Co., Ltd. Colloidal quantum dots in red (CdZnSe/ZnS/oleic acid, core and shell ≈12.2 nm), green (CdZnSeS/ZnS/oleic acid, core and shell ≈11.6 nm), and blue (CdZnSeS/ZnS/oleic acid, core and shell ≈10.5 nm) varieties were sourced from Suzhou Xingshuo Nanotech Co., Ltd.
Device fabrication
Inverted QLEDs: glass/ITO (80 nm)/ZMO (x nm)/QDs (~15 nm)/CBP (50 nm)/MoO3 (10 nm)/Al (100 nm), where the thickness of ZMO layer ranged from 40 nm to 150 nm.
Tandem QLEDs: glass/ITO (x nm)/ZMO_B (y nm)/QDs (~15 nm)/CBP (50 nm)/MoO3 (10 nm)/IZO (z nm)/ZMO_T (k nm)/QDs (~15 nm)/CBP (50 nm)/MoO3 (10 nm)/Al (100 nm) were fabricated. Abbreviation: ZMO_B = bottom ZnMgO, ZMO_T = top ZnMgO. The thicknesses of bottom ITO, ZMO_B, intermediate IZO, and ZMO_T were optimized to maximize the light outcoupling efficiency. By simulations and experiments, the optimal thicknesses of bottom ITO, ZMO_B, intermediate IZO, and ZMO_T are fixed as 80 nm, 110 nm, 25 nm, and 90 nm, respectively.
For the inverted QLEDs, the ITO glass substrates were cleaned with detergent and deionized water in an ultrasonic bath for 30 min and then dried in an oven at 60 °C for 30 min. After cleaning, the ZMO solution (40 mg mL−1 in ethanol) and the QDs solution for red (R), green (G), blue (B), or yellow (Y) emission layers were layer-by-layer deposit by statically spin-casting at 3000 r.p.m. for 45 s, as shown in Supplementary Fig. 10a. The ZMO layer and QDs layer were then baked at 100 °C for 10 min and 5 min, respectively, to form the electron transport layer (ETL) and the respective emission layers (EML). For R-, G-, and B- QDs, the solutions were 15 mg mL−1 in octane. For the Y-QDs emission layer, a mixed QDs solution was prepared by combining R-QDs (15 mg mL−1 in octane) and G-QDs (15 mg mL−1 in octane) with a volume ratio of 1:10. Subsequently, under a base pressure of 4 × 10−4 Pa, the hole transport layer (HTL) of CBP and the hole injection layer (HIL) of MoO3 were sequentially deposited onto the QDs layer at rates of 1.5 Å s−1 and 0.2 Å s−1, respectively. Then, Al electrodes (100 nm) were deposited using the same method at a rate of 5 Å s−1. The device area defined by the overlapping of the ITO and Al electrodes is 1 mm2. Finally, the QLEDs were encapsulated with UV-resin and cover glass.
For tandem QLEDs, the fabrication processes for the first part, glass/ITO/ZMO_B/QD/CBP/MoO3, mirrored those of the inverted QLED. Following the MoO3 deposition, the samples were transferred to a magnetron sputtering system to deposit the IZO electrode at varying thicknesses under a working pressure of 0.45 Pa, a power of 50 W, and an Ar flow of 20 sccm. Subsequently, the ZMO solution (40 mg mL−1 in ethanol) and the QDs solution were layer-by-layer deposited by dynamically spin-casting at 3000 r.p.m. for 45 s, as shown in Supplementary Fig. 10b. The ZMO layer and QD layer were then baked at 60 °C for 20 min and 10 min, respectively, in a nitrogen-filled glovebox to form the ETL (ZMO_T) and EML. Following this, the CBP, MoO3, and Al were thermally deposited under the same conditions as the inverted QLEDs. The device area defined by the overlapping of the ITO, IZO, and Al electrodes is 1 mm2. Finally, the QLEDs were encapsulated with UV-resin and cover glass. Supplementary Fig. 11 illustrates the fabrication processes developed to achieve tandem QLEDs without damage.
Characterizations
The thicknesses of ITO, IZO, ZMO, and QD film were determined utilizing a Bruker DektakXT stylus profiler. In situ monitoring of the evaporation rates and thicknesses of CBP, MoO3, and Al electrodes was conducted using a quartz crystal microbalance. The EL spectra of QLEDs were recorded in the standard direction using a fiber-optic spectrometer (Ocean Optics USB 2000). The J-V-L, EQE, and PE characteristics of QLEDs were obtained using a home-built system comprising a dual-channel Keithley 2614B programmable source meter and a PIN-25D calibrated silicon photodiode (PD). To measure the performance of (PnP-QLED)n, the (PnP-QLED)n were driven by AC electricity at 50 Hz using an isolation transformer. The AC voltage dropped across the (PnP-QLED)n and the current flowing through the (PnP-QLED)n were recorded by a dual-channel oscilloscope (Tektronix, TBS1102). The luminous flux generated by the (PnP-QLED)n was measured by a PIN-25D calibrated silicon photodiode. The schematic measurement setup is shown in Supplementary Fig. 21. The average of PE, EQE, and CE of the (PnP-QLED)n were calculated by using the measured Iavg, Pavg, lumens, and spectra of the devices as the inputs.
Data availability
The data that support the findings of this study are available from the corresponding author upon request.
References
Tonzani, S. Lighting technology: time to change the bulb. Nature 459, 312–314 (2009).
Liang, J., Li, L., Niu, X., Yu, Z. & Pei, Q. Elastomeric polymer light-emitting devices and displays. Nat. Photonics 7, 817–824 (2013).
Chen, Z. et al. Color revolution: prospects and challenges of quantum-dot light-emitting diode display technologies. Small Methods 2, e2300359 (2023).
Schubert, E. F. & Kim, J. K. Solid-state light sources getting smart. Science 308, 1274–1278 (2005).
Chen, S. et al. On the degradation mechanisms of quantum-dot light-emitting diodes. Nat. Commun. 10, 765 (2019).
Gao, Y. et al. Minimizing heat generation in quantum dot light-emitting diodes by increasing quasi-Fermi-level splitting. Nat. Nanotechnol. 18, 1168–1174 (2023).
Wang, S. et al. A flicker-free electrolytic capacitor-less AC-DC LED driver. IEEE Trans. Power Electron. 27, 4540–4548 (2012).
Cho, Y. W., Kwon, J. M. & Kwon, B. H. Single power-conversion AC-DC converter with high power factor and high efficiency. IEEE Trans. Power Electron. 29, 4797–4806 (2014).
Chiu, H. J. et al. A high-efficiency dimmable LED driver for low-power lighting applications. IEEE Trans. Ind. Electron. 57, 735–743 (2010).
Zhang, F., Ni, J. & Yu, Y. High power factor AC-DC LED driver with film capacitors. IEEE Trans. Power Electron. 28, 4831–4840 (2013).
Pollock, A., Pollock, H. & Pollock, C. High efficiency LED power supply. IEEE J. Emerg. Sel. Top. Power Electron. 3, 617–623 (2015).
Malcovati, P., Belloni, M., Gozzini, F., Bazzani, C. & Baschirotto, A. A 0.18-µm CMOS, 91%-efficiency, 2-A scalable buck-boost DC-DC converter for LED drivers. IEEE Trans. Power Electron. 29, 5392–5398 (2014).
Yu, W., Lai, J. S., Ma, H. & Zheng, C. High-efficiency DC-DC converter with twin bus for dimmable LED lighting. IEEE Trans. Power Electron. 26, 2095–2100 (2011).
Lee, K., Nubbe, V., Rego, B., Hansen, M. & Pattison, P. 2020 LED manufacturing supply chain. Tech. Rep. https://www.researchgate.net/publication/351732644 (2021).
Lee, S. B., Fujita, K. & Tsutsui, T. Emission mechanism of double-insulating organic electroluminescence device driven at AC voltage. Jpn. J. Appl. Phys. 44, 6607 (2005).
Wang, Y. Z. et al. Alternating-current light-emitting devices based on conjugated polymers. Appl. Phys. Lett. 68, 894–896 (1996).
Hitt, J. C., Bender, J. P. & Wager, J. F. Thin-film electroluminescent device physics modeling. Crit. Rev. Solid. State 25, 29–85 (2000).
Xu, X. L. et al. Direct interband transitions in tris-(8-hydroxyquinoline) aluminum thin films. J. Appl. Phys. 89, 1082–1086 (2001).
Perumal, A. et al. Novel approach for alternating current (AC)‐driven organic light‐emitting devices. Adv. Funct. Mater. 22, 210–217 (2012).
Perumal, A., Lüssem, B. & Leo, K. High brightness alternating current electroluminescence with organic light emitting material. Appl. Phys. Lett. 100, 103307 (2012).
Fröbel, M., Hofmann, S., Leo, K. & Gather, M. C. Optimizing the internal electric field distribution of alternating current driven organic light-emitting devices for a reduced operating voltage. Appl. Phys. Lett. 104, 71105 (2014).
Zhang, L., Nakanotani, H., Yoshida, K. & Adachi, C. Analysis of alternating current driven electroluminescence in organic light emitting diodes: a comparative study. Org. Electron. 15, 1815–1821 (2014).
Liu, S. Y., Chang, J. H., Wu, I. W. & Wu, C. I. Alternating current driven organic light emitting diodes using lithium fluoride insulating layers. Sci. Rep. 4, 7559 (2014).
Wang, K. et al. Electroluminescence from μLED without external charge injection. Sci. Rep. 10, 8059 (2020).
Bozyigit, D., Wood, V., Shirasaki, Y. & Bulovic, V. Study of field driven electroluminescence in colloidal quantum dot solids. J. Appl. Phys. 111, 6607 (2012).
Bozyigit, D. & Wood, V. Challenges and solutions for high-efficiency quantum dot-based LEDs. MRS Bull. 38, 731–736 (2013).
Cho, S. H. et al. Extremely bright full color alternating current electroluminescence of solution-blended fluorescent polymers with self-assembled block copolymer micelles. ACS Nano 7, 10809–10817 (2013).
Sung, J. et al. AC field-induced polymer electroluminescence with single wall carbon nanotubes. Nano Lett. 11, 966–972 (2011).
Chen, Y., Xia, Y., Smith, G. M. & Carroll, D. L. Frequency-dependent, alternating current-driven, field-induced polymer electroluminescent devices with high power efficiency. Adv. Mater. 26, 8133–8140 (2014).
Chen, Y. et al. High-color-quality white emission in AC-driven field-induced polymer electroluminescent devices. Org. Electron. 15, 182–188 (2014).
Chen, Y. et al. Solution-processable hole-generation layer and electron-transporting layer: Towards high-performance, alternating-current-driven, field-induced polymer electroluminescent devices. Adv. Funct. Mater. 24, 2677–2688 (2014).
Chen, Y. et al. Solution-processed highly efficient alternating current-driven field-induced polymer electroluminescent devices employing high k relaxor ferroelectric polymer dielectric. Adv. Funct. Mater. 24, 1501–1508 (2014).
Xia, Y. et al. Alternating current-driven, white field-induced polymer electroluminescent devices with high power efficiency. Org. Electron. 15, 3282–3291 (2014).
Lee, J. H. et al. A field-induced hole generation layer for high performance alternating current polymer electroluminescence and its application to extremely flexible devices. J. Mater. Chem. C 4, 4434–4441 (2016).
Xia, Y. et al. High-performance alternating current field-induced chromatic-stable white polymer electroluminescent devices employing a down-conversion layer. J. Lumin. 161, 82–86 (2015).
Xu, J., Carroll, D. L., Smith, G. M., Dun, C. & Cui, Y. Achieving high performance in AC-field driven organic light sources. Sci. Rep. 6, 24116 (2016).
Xu, J. et al. Solution processing small-molecule organic emitter in field-induced, carrier gated lighting devices. Adv. Opt. Mater. 5, 798 (2017).
Cho, S. H. et al. High performance AC electroluminescence from colloidal quantum dot hybrids. Adv. Mater. 24, 4540–4546 (2012).
Xia, F., Sun, X. W. & Chen, S. Alternating-current driven quantum-dot light-emitting diodes with high brightness. Nanoscale 11, 5231–5239 (2019).
Chen, J., Liu, M., Ji, J., Ali, M. U. & Meng, H. Alternating current-driven quantum-dot light-emitting diodes with planar architecture. Appl. Phys. Lett. 118, 8133 (2021).
Xu, J. et al. Layered, nanonetwork composite cathodes for flexible, high-efficiency, organic light emitting devices. Adv. Funct. Mater. 25, 4397–4404 (2015).
Guo, F. et al. The fabrication of color-tunable organic light-emitting diode displays via solution processing. Light. Sci. Appl. 6, e17094 (2017).
Oh, N. et al. Double-heterojunction nanorod light-responsive LEDs for display applications. Science 355, 616–619 (2017).
Xu, J. et al. Polymer gating white flexible field-induced lighting device. Adv. Mater. Technol. 2, 1700017 (2017).
Xu, J. et al. Tailoring spin mixtures by ion-enhanced Maxwell magnetic coupling in color-tunable organic electroluminescent devices. Light. Sci. Appl. 7, 46 (2018).
Lee, S. et al. Alternating‐current MXene polymer light‐emitting diodes. Adv. Funct. Mater. 30, 168 (2020).
Liu, J. et al. Low power consumption red light-emitting diodes based on inorganic perovskite quantum dots under an alternating current driving mode. Nanomaterials 8, 974 (2018).
Song, S. H. et al. All-solution-processed colour-tuneable tandem quantum-dot light-emitting diode driven by AC signal. Nanoscale 12, 17020–17028 (2020).
Zhang, J., Tsai, H., Nie, W., Hu, B. & Enabling, A. C. electroluminescence in quasi-2D perovskites by uniformly arranging different-n-value nanoplates to allow bidirectional charge transport. Nano Energy 79, 105413 (2021).
Adão, R. M. R., Sun, T., Romeira, B., Alpuim, P. & Nieder, J. B. Spectral-temporal luminescence properties of colloidal CdSe/ZnS quantum dots in relevant polymer matrices for integration in low turn-on voltage AC-driven LEDs. Opt. Express 30, 10563–10572 (2022).
Fröbel, M. et al. Get it white: color-tunable AC/DC OLEDs. Light. Sci. Appl. 4, e247–e247 (2015).
Ji, J. et al. Three-phase electric power driven electroluminescent devices. Nat. Commun. 12, 54 (2021).
Zhao, C. et al. Alternating‐current-driven color-tunable organic light-emitting triodes. Adv. Opt. Mater. 9, 2001655 (2021).
Kim, E. H. et al. Organic light emitting board for dynamic interactive display. Nat. Commun. 8, 14964 (2017).
Xu, X. et al. Polar-electrode-bridged electroluminescent displays: 2D sensors remotely communicating optically. Adv. Mater. 29, 1703552 (2017).
Zhang, X., Liu, S., Zhang, L. & Xie, W. In‐planar-electrodes organic light-emitting devices for smart lighting applications. Adv. Opt. Mater. 7, 1703552 (2019).
Zhang, X. et al. Color-tunable, spectra-stable flexible white top-emitting organic light-emitting devices based on alternating current driven and dual-microcavity technology. ACS Photonics 6, 2350–2357 (2019).
Wang, T., Chen, Z., Zhang, H. & Ji, W. Color-tunable alternating-current quantum dot light-emitting devices. ACS Appl. Mater. Interfaces 13, 45815–45821 (2021).
Zhang, H., Wang, J. & Chen, S. 220 V/50 Hz compatible bipolar quantum-dot light-emitting diodes. Adv. Mater. 36, 2312334 (2024).
Zhang, H., Su, Q. & Chen, S. Quantum-dot and organic hybrid tandem light-emitting diodes with multi-functionality of full-color-tunability and white-light-emission. Nat. Commun. 11, 2826 (2020).
Dai, X. et al. Solution-processed, high-performance light-emitting diodes based on quantum dots. Nature 515, 96–99 (2014).
Shu, Y. et al. Quantum dots for display applications. Angew. Chem. Int. Ed. 59, 22312–22323 (2020).
Dai, X., Deng, Y., Peng, X. & Jin, Y. Quantum-dot light-emitting diodes for large-area displays: towards the dawn of commercialization. Adv. Mater. 29, 1604022 (2017).
García de Arquer, F. P. et al. Semiconductor quantum dots: technological progress and future challenges. Science 373, eaaz8541 (2021).
Liu, M. et al. Colloidal quantum dot electronics. Nat. Electron. 4, 548–558 (2021).
Zhang, H., Su, Q., Sun, Y. & Chen, S. Efficient and color stable white quantum-dot light-emitting diodes with external quantum efficiency over 23%. Adv. Opt. Mater. 6, 1800354 (2018).
Qian, L., Zheng, Y., Xue, J. & Holloway, P. H. Stable and efficient quantum-dot light-emitting diodes based on solution-processed multilayer structures. Nat. Photonics 5, 543–548 (2011).
Neyts, K. A. Simulation of light emission from thin-film microcavities. J. Opt. Soc. Am. A 15, 962–971 (1998).
Furno, M., Meerheim, R., Hofmann, S., Lüssem, B. & Leo, K. Efficiency and rate of spontaneous emission in organic electroluminescent devices. Phys. Rev. B 85, 115205 (2012).
Barnes, W. L. Fluorescence near interfaces: the role of photonic mode density. J. Mod. Opt. 45, 661–699 (1998).
Barnes, W. L. Electromagnetic crystals for surface plasmon polaritons and the extraction of light from emissive devices. J. Lightwave Technol. 17, 2170 (1999).
Acknowledgements
This work was supported by the National Natural Science Foundation of China, No. 62174075 (S.C.), Shenzhen Science and Technology Program, Nos. JCYJ20210324105400002 (S.C.), JCYJ20220530113809022 (S.C.) and JCYJ20230807093604009 (S.C.).
Author information
Authors and Affiliations
Contributions
S.C. conceived the idea, supervised the work, and wrote the majority of the final manuscript. J.W. conducted the experiments, collected the data, drew the figures, and wrote the original draft. C.Y. discussed the optical simulation results. All authors discussed the results and reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Cheolmin Park, Jangkun Song, and the other anonymous reviewer(s) for their contribution to the peer review of this work. A peer review file is available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Wang, J., Yuan, C. & Chen, S. Household alternating current electricity plug-and-play quantum-dot light-emitting diodes. Nat Commun 15, 3512 (2024). https://doi.org/10.1038/s41467-024-47891-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-024-47891-4
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.