We used x-ray absorption spectroscopy and x-ray magnetic circular dichroism to investigate the effects of inserting Cu into Co/Pt interfaces, and found that a 0.4-nm-thick inserted Cu layer showed perpendicularly magnetized properties induced by the proximity effect through the Co and Pt layers. The dependence of the magnetic properties on the thickness of the Cu layers showed that the proximity effects between Co and Pt with perpendicular magnetic anisotropy can be prevented by the insertion of a Cu layer with a nominal threshold thickness of 0.7 nm. Element-specific magnetization curves were also obtained, demonstrating that the out-of-plane magnetization is induced in the Cu layers of the Co/Cu/Pt structures.
Perpendicular magnetic anisotropy (PMA) in magnetic multilayers with a high anisotropy constant (K [J · m−3]) is strongly desired for the development of high-density magnetic recording media because large PMA values can overcome thermal energy (kBT) near room temperature, where kBT ≈ 4 × 10−21 J as long as KV/kBT ≥ 60, even with nanoscale volumes (V) on the order of 10−24 m3 1,2. CoPt alloys such as granular alloys and core-shell particles are candidates for demonstrating PMA through the large spin-orbit interaction of Pt atoms and the spin magnetic moments of Co atoms, which collaborate to enhance the PMA. There are many reports discussing PMA in Co/Pt interfaces, Co-Pt alloys, and granular thin films3,4,5,6,7,8, especially using x-ray magnetic circular dichroism (XMCD) to deduce the element-specific spin and orbital magnetic moments. Anisotropy of orbital magnetic moments is expected to play an important role in PMA. Recently, ultrathin Co/Pt layers have been extensively studied for the electric-field modulations of magnetic properties and spin-torque magnetic switching9,10,11. Moreover, the Co/Cu multilayer structures possessing in-plane anisotropy derived from the shape anisotropy in thin films have been investigated extensively because they are utilized for giant magneto-resistance devices12,13,14,15. The non-magnetic Cu spacer layers cause behavior similar to Ruderman-Kittel-Kasuya-Yosida (RKKY) oscillatory behavior in the exchange coupling between the magnetic Co layers15,16,17,18. Induced magnetism in Cu is also observed through the proximity effect with magnetic atoms19,20,21,22,23. Considering all of these physical phenomena, our present research had two goals: (i) the insertion of the Cu layer as an intermediate layer between Co and Pt in order to separate the magnetic coupling between them, and (ii) the attainment of induced PMA in Cu sandwiched between Co and Pt. To achieve these properties, we considered stacked structures of Co/Cu/Pt thin films with different Cu layer thicknesses.
There have been some prior efforts to insert a Cu layer into Co/Pt interfaces to prevent inter-diffusion at the interfaces and the resulting decrease of the PMA24,25. However, the problem of understanding the element-specific analysis in these structures remains unsolved. XMCD is a powerful technique to elucidate element-specific magnetic properties and to deduce the spin and orbital magnetic moments using the magneto-optical sum rules for each element26. Furthermore, it is well-accepted that PMA is proportional to the anisotropy of the orbital magnetic moments, as predicted by Bruno27. However, considering that the large spin-orbit interaction in Pt 5d states affects the PMA in the Co layer, the details of how to apply this formula are still being debated28,29,30,31,32, and the relationship between orbital magnetic moments and PMA is not completely understood. Therefore, a better understanding of the orbital moment anisotropy in the Co/Pt interface and its modulation by Cu insertion is required in order to implement novel material designs possessing PMA. Furthermore, the phenomena of induced PMA in non-magnetic elements have high potential for opening up a new research field considering the interfacial proximity effects. We emphasize that the detailed investigations for proximity-driven PMA using XMCD and theoretical calculation are the challenging subjects in spintronics research fields. In this paper, we investigate the element-specific spin and orbital moments of Co, Cu, and Pt in Co/Cu/Pt stacked structures using XMCD with element-specific magnetization curves in order to elucidate the origin of the proximity-effect-driven out-of-plane magnetization in the Cu inserted layer.
Measurements of total magnetic moments
Figure 1 shows the dependence of the remanent magnetic moment of the stacked samples as a function of the thickness of the Cu layer. Since the individual contributions of the induced magnetic moments in the Cu and Pt layers are not separated, we adopt the units of Amperes, where the remanent magnetic moment (mr [A · m2]) is divided by the sample area (S [m2]) for the ordinate of Fig. 1. For reference purposes, the cases in which the Cu layers were deposited on top of the Co/Pt layers are also displayed. The values of mr/S plotted in Fig. 1 for the Cu/Co/Pt structures are nearly constant, which demonstrates that the proximity effect between the Co and the Pt layers has a major influence on the PMA. However, when the Cu layer is inserted between the Co and Pt layers, mr decreases rapidly as soon as the Cu thickness passes the 0.6 nm, suggesting that the proximity effects for PMA are weakened by the insertion of Cu layers. For a Cu thicknesses less than 0.6 nm, the mr decreases slightly, and the line shapes in the hysteresis curves retain square features. Near the threshold thickness of 0.7 nm, the square shapes start to become broad, and mr decreases as shown in Fig. 1. For Cu layer thicknesses larger than the threshold, the in-plane magnetic moment of Co derived from the demagnetization field in the films becomes dominant. These systematic changes suggest the disconnection between Co and Pt layer at the nominal threshold thickness of Cu 0.7 nm.
Figure 2 shows the X-ray absorption spectroscopy (XAS) spectra and the XMCD spectra of Co, Cu, and Pt for Co/Cu/Pt structures with nominal thicknesses of 0.4, 0.4, and 2.0 nm, respectively, with surface capping layer of 2-nm-thick MgO. All XAS spectra were normalized at L3 edge intensities in order to compare the intensities of XMCD. In the Co L-edge spectra, clear metallic XAS line shapes and clear XMCD can be observed, suggesting that the Co atoms are not oxidized at the interface with the MgO capping layer. Asymmetry between L3 and L2 XMCD intensities brings the orbital magnetic moments within the framework of magneto-optical sum rules26. Angular dependence shows the difference in the intensity ratio. In the grazing incidence (GI) case, L3 intensities become smaller than those in the normal incidence (NI) case, suggesting that the orbital moment in GI is smaller than that in NI. On the other hand, extremely small XMCD intensities in the Cu L-edges were detected as shown in Fig. 2(b), which suggests that the XMCD signals in Cu are induced by the magnetic Co atoms with sign directions corresponding to the parallel alignments. Broad satellite structures in Cu L2,3-edge XAS are also observed at 931 eV and 952 eV corresponding to the transition from 2p to 4 s states, but these do not contribute to the XMCD signals. Similar satellite structures have been previously observed in the XAS spectra of Co/Cu multilayers22. In the case of Cu XMCD, very small differences in the intensity ratio between L3 and L2 can be observed, which suggests a small anisotropic orbital magnetic moment in Cu. In the Pt L2,3-edge XAS shown in Fig. 2(c), oscillatory line shapes appear above the main absorption edges due to the onset of extended X-ray absorption fine structure oscillation. The XMCD intensities in Pt L edges are weakened to half of maximum compared with those in the interface of Co (0.4 nm)/Pt (2.0 nm). This fact can be mainly explained by the insertion of Cu layers between Co and Pt because only the interfacial regions of Pt contribute to the magnetic properties through proximity with Co and Cu.
Next, we show the XAS and XMCD in the case of 2-nm-thick Cu sandwiched between 0.4-nm-thick Co and 2-nm-thick Pt layers (Fig. 3). This sample shows in-plane magnetization. All XAS spectra displayed are also normalized in the same manner as shown in Fig. 2 in order to compare the XMCD signal intensities. In Co L-edge XMCD, angular dependence remains unchanged in the L3 and L2 intensity ratio, which suggests that the difference in the orbital moments in the case of in-plane anisotropy is suppressed through the disconnection between Pt and Co layers by the 2-nm-thick Cu layer. The Cu L-edge XMCD intensities become almost half of those in the 0.4 nm case shown in Fig. 2. This is derived from the fact that the interfacial Cu layer is spin-polarized and the bulk component in the 2-nm-thick Cu layer does not contribute to the spin polarization. Furthermore, the Pt L-edge XMCD signals cannot be observed as shown in Fig. 3 (c). These results indicate that the intermixing between the layers is suppressed, and the Co and Pt layers are disconnected.
Through spectral analysis of XMCD, we deduced the spin and orbital magnetic moments for each element, which are listed in Table 1. The effective spin moments including the magnetic dipole terms were estimated from the spin sum rule at NI and the spin moments were deduced from the analysis of the GI case33. The magnetic dipole terms were derived from the difference between these two values. The spin moment values for each element were calculated to be 1.67, 0.05, and 0.07 μB for Co, Cu, and Pt, respectively, with uncertainties of ±20%. We adopted the hole numbers of nCo = 2.4, nCu = 0.4, and nPt = 1.8 which are estimated from the band-structure calculations. Suzuki et al. reported the spin and orbital moment values of Pt as 0.144 and 0.018 μB, respectively, for the Co/Pt interface8. Both spin and orbital moment values of Pt deduced in our case are half of those estimated for the Co/Pt interface4,8 because of the suppression of the direct proximity between Co and Pt atoms. The perpendicular components in orbital moments of each element taken at NI were calculated to be 0.15, 0.01, and 0.005 μB for Co, Cu, and Pt, respectively. The values in Co and Cu are slightly larger than those reported previously for in-plane Co/Cu multilayers17. Although the interfacial Pt layer is spin-polarized by proximity, the polarization decays rapidly in the bulk. Since XMCD analyses include both interfacial and bulk contributions, we cannot deduce the precise values for Pt. However, we compared with the case of the same system without the Cu layer insertion. XMCD intensity in Pt becomes twice as large as the results in Fig. 2. Therefore, we confirmed not only the decay in bulk components but also proximity at the interfaces. The anisotropy of orbital moments Δmorb = (morb⊥ − morb//) in Co sites was calculated and found to have a value of 0.02 μB. This quantity can be related to the PMA energy K arising from Co atoms by applying Bruno’s relationship: K = −(G/H) ξCoΔmorb/(4 μB), where ξCo is the spin-orbit coupling constant of Co, and G/H is a parameter depending on the band structure27. Since the setup in the GI case involved a 60° angle between the magnetic field and the sample surface normal directions, the precise in-plane morb// cannot be detected; this underestimates the in-plane components. From the above results, we conclude that the interfacial K values are less than the order of 102 μJ/m2 for Co sites. The anomalous Hall effect measurements represent the K value to be almost 102 μJ/m234,35. Therefore, orbital moment anisotropy for PMA can be adopted to Co sites where the large spin-orbit interactions of Pt atoms are responsible for PMA.
Figure 4 shows the element-specific magnetization curves taken at photon energies of the Co and Cu L3-edges. In the case of the Co L3 edges, the angular dependence clearly displays the existence of PMA because GI x-rays show behavior typical of hard-axis directions, i.e., magnetic fields greater than ±0.5 T are necessary to achieve the saturation of the magnetization. When considering the magnetization curves of the Co L3-edge in the case of 2-nm-thick Cu as shown in Fig. 4(c), the magnetic easy axis in the Co sites is changed from the perpendicular to the in-plane direction with increasing Cu layer thickness. The features of the magnetization curves measured by XMCD are almost consistent with the measurements obtained by superconducting quantum interference device (SQUID) shown in Fig. 1. Here, we emphasize that the magnetization curve of Cu XMCD also displays out-of-plane magnetization as shown in Fig. 4(b), which is induced by proximity effects operating on both Co and Pt. In the case of Co/Cu multilayers, in-plane induced magnetization in Cu has been observed previously in XMCD15,16,19. Therefore, the out-of-plane magnetization in Cu is derived not only from Co but also from Pt spin-orbit interactions. Clear magnetization features in XMCD provide evidence that the out-of-plane magnetization in Cu in Co/Cu/Pt stacked structures originates from the contribution of all layers.
The XMCD results clearly suggest that the thick Cu layer prevents PMA at the Co/Pt interface, resulting in in-plane magnetism in Co and eliminating XMCD intensity in Pt because of the disconnection of the proximity effects at the Co/Pt interface. However, in the case of a thin Cu layer, of less than 0.7 nm, the proximity among Co, Cu, and Pt contributes to the PMA. Element-specific magnetization curves in XMCD successfully detected the out-of-plane magnetism in Cu.
We carried out a first-principles calculation for the MgO/Co/Cu/Pt stacked structure as shown in Fig. 5(a). We recognize the thickness of Co 2 monolayer (ML) corresponds to the 0.4 nm. Element-specific electronic structures of each layer can be deduced from the band-structure calculation. The density of states (DOS) of Co 3d states at the Co/Cu interface is clearly split with the spin magnetic moment of 1.72 μB as shown in Fig. 5(b). We also evaluated the magnetic anisotropy energy projected into each atomic site in order to analyze the origin of the PMA. Using the analysis for each layer, the orbital moment anisotropy of Co atoms at the Co/Cu interfacial layer was estimated to be 0.007 μB, and the PMA of the Co layers can be augmented mainly by the contribution of the interface layer between Co and MgO. The 3dxz (dyz) orbital of Co atoms has a higher DOS around the Fermi level than the other 3d orbitals at the Co/MgO interface. Within the framework of second-order perturbation theory of the spin-orbit coupling27, the coupling between the dxz and dyz states above and below the Fermi level gives rise to the PMA. The DOS of Cu 3d states is also split as shown in Fig. 5(c) because of the proximity of the Co layers. Induced spin magnetic moments of 0.03 μB are also estimated in the Cu 3d states. However, induced orbital magnetic moments in Cu are estimated to be almost zero. Since the Cu 3d states are almost all occupied, the DOS at the Fermi level is quite small, which suggests that the Stoner conditions for ferromagnetism are not satisfied in Cu. The induced spin magnetic moment of Pt atoms at the Co/Pt interface was estimated to be 0.18 μB, but it was decreased to 0.025 μB by inserting two-monolayer (ML) Cu because of the small spin splitting of Pt 5d DOS as shown in Fig. 5(d). The induced magnetic moments are caused by the d-orbital hybridization between neighbor Co and Pt atoms, which qualitatively coincides with the fact that the Pt XMCD intensities are suppressed by inserting Cu, in addition, the proximity effects are drastically suppressed by inserting Cu layer.
In order to investigate the interfacial and bulk components, the magnetic anisotropy energy (MAE) in each layer is resolved and shown in Fig. 6. We performed the calculations for the Cu 1–3 ML cases. Positive MAE values stabilize the PMA. With increasing Cu layer thickness, PMAs in the Cu and Pt interfaces decrease. In the Cu 2 ML case, the Cu layers clearly contribute to the PMA. Note that the top Co shows a large PMA because of the contact with the artificial MgO interface. Furthermore, the lattice constants for Cu and Co are adjusted to that in Pt, which might induce strain effects for the magnetic layers. The theoretical calculations show the induced magnetism in Cu is derived from proximity with the Co layer, which supports the XMCD intensity in the Cu L-edges displayed in Fig. 2.
Considering the above results, we discuss the origins of out-of-plane magnetization in Cu. First, spin-orbit coupling constants ξ of Co and Pt are estimated by the first-principles calculations to be almost 60 and 550 meV/atom, respectively29. Since the orbital moment anisotropy in Co sites is derived from the spin-orbit interaction, the contribution of Pt atoms for the appearance of PMA becomes essential30. On the other hand, the exchange coupling between Co and Cu aligns the spin directions parallel to each other. As demonstrated in the Co/Cu multilayers with in-plane magnetization, RKKY-like oscillatory behaviors in the exchange coupling strength can be expected depending on the spacer-layer thicknesses15. Bruno’s relation using the orbital moment anisotropy is based on the assumption that the perturbation energy of the spin-orbit interaction is much weaker than the exchange splitting energy. The oscillatory behaviors of exchange coupling in the PMA cases might be stabilized by the competition between interfacial PMA energy K and exchange coupling constants, which introduces new physics to the modeling of the orbital magnetic moments. Interfacial PMA energy of Co sites is also estimated from the first-principles calculation. The calculation suggests an interfacial PMA energy of about 102 μJ/cm2, on the same order as the results of the magnetization measurements and XMCD analysis. However, the calculation suggests that not only orbital moment anisotropy assuming the large exchange splitting but also the independent spin-flip contribution has to be treated at the interfaces in the MgO/Co/Cu/Pt system32.
Second, the relationship between proximity and exchange coupling in Cu must be discussed. PMA in Co/Pt is derived from the hybridization between Co 3d and Pt 5d wave functions, but that is disconnected by the Cu layer because the Cu 3d orbitals interrupt the Co-Pt proximity. Since the electronic structures of the three monolayers of Cu are different from those in the bulk, the exchange splitting in Cu can be induced through the hybridization with Co 3d states, which arises not from the Stoner conditions between para- and ferromagnetism but from proximity effects among Co/Cu/Pt layers. Therefore, the PMA energies in systems with inserted Cu are weakened.
Third, we comment on the comparison of spin magnetic moments as determined by the analysis of XMCD and by the band-structure calculation listed in Table 1. Band-structure calculation suggests that the magnetic moment values strongly depend on the layer structures. The subtle interfacial roughness affects the magnetic properties. The systematic Cu layer thickness dependence in the magnetization shown in Fig. 1 reveals the formation close to abrupt interfaces, which cannot be detected even by cross-sectional transmission electron microscopy for ultrathin films. Discrepancy in magnetic moments between the analysis of XMCD and the band-structure calculation might be derived from the interfacial roughness that is inevitably formed in the atomic scale, although physical pictures are reproduced qualitatively.
Fourth, we discuss the crystal structures of the thin Cu layer. The Fe/Cu interface showed body-centered-cubic, and the Co/Cu interface showed face-centered-cubic structures21. In both cases, induced XMCD in Cu layers was observed, suggesting that the proximity effects connected with ferromagnetic layers derive an induced magnetism in Cu that is independent of crystal structure.
Finally, we discuss the interfacial and bulk components in PMA. In the case of Cu 2 ML, both layers contact other elements. Although XMCD cannot distinguish these contributions, the layer-specific first-principle calculations depict the interfacial components. Although abrupt interfaces are assumed in the calculation, the qualitative tendency can explain the variation of XMCD results with Cu layer thicknesses.
In conclusion, we investigated the effect of inserting Cu into Co/Pt interfaces using XMCD along with the analysis of the element-specific spin and orbital magnetic moments in each element by means of magnetization curves in XMCD. We found that a 0.4-nm-thick inserted Cu layer shows perpendicularly magnetized properties that are induced by the proximity effect through the Co and Pt layers. Thickness dependencies of the Cu layers suggest that the proximity effects between Co and Pt with PMA can be prevented by insertion of a Cu layer with a nominal threshold thickness of 0.7 nm.
Samples were prepared by RF sputtering. The stacked structures consisting of MgO (2.0 nm)/Co (0.4 nm)/Cu (t nm)/Pt (2.0 nm)/Ta (2.8 nm) layers were deposited at room temperature on Si (001) substrates (with the Ta next to the Si, and the MgO on top). The Pt layer is oriented normal to the  direction34. Here, the Cu layer thicknesses, t, of 0.4 and 2.0 nm were used for the PMA and for the in-plane anisotropy, respectively, in the XMCD measurements. The thicknesses of the layers were calibrated by the deposition rate of each material for the growth of precisely controlled stacked structures34. The MgO layer acted as a capping layer, preventing the oxidization of the sample surfaces. Magnetic properties of the samples were measured with a SQUID magnetometer.
XAS and XMCD measurements for Co and Cu L-edges were performed at BL-7A and 16A in the Photon Factory high-energy accelerator research organization (KEK) using the total electron yield mode. Photon helicity was fixed, and a magnetic field of ±1.2 T was applied parallel to the incident circularly polarized soft x-ray beam. For the Pt L-edge XMCD measurements, we employed the partial fluorescent yield mode at SPring-8 BL39XU8. All measurements were carried out at room temperature. Angular-dependent XMCD was performed by rotating the angle between the incident beam and the direction of the sample’s surface normal from the surface normal to 60°; these geometries are defined as NI and GI, respectively. In the case of the NI setup, where both the photon helicity and the magnetic field directions are normal to the surface, the X-ray absorption processes involve the normal direction components of the orbital angular momentum (morb⊥). The GI setup mainly allows the detection of only the in-plane orbital momentum components (morb//).
A first-principles band-structure calculation on the basis of density-functional theory was performed using the Vienna ab initio simulation package36,37 with the spin-polarized generalized gradient approximation (GGA)38. We constructed a supercell containing three layers of Mg, O, Co, and Cu atoms and five layers of Pt atoms. All atomic positions were relaxed until the Hellman-Feynman force was below 0.02 eV/Å with the in-plane lattice constant fixed to that of face-centered-cubic Pt (0.26 nm). The plane-wave cutoff energy was set to 500 eV and a 24 × 24 × 1 k-points Monkhorst-Pack mesh was used for sampling in the Brillouin zone. The magnetic anisotropy energy was evaluated using the magnetic force theorem. The atomic site projected magnetic anisotropy energy of i atom was calculated by the following equation:
where εn,k, ψn,k and βi are the eigenvalue, the Bloch wave function with band index n, and the projector function on the atomic spheres, respectively.
How to cite this article: Okabayashi, J. et al. Induced Perpendicular Magnetization in a Cu Layer Inserted between Co and Pt Layers Revealed by X-ray Magnetic Circular Dichroism. Sci. Rep. 7, 46132; doi: 10.1038/srep46132 (2017).
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Weller, D. & Moser, A. Thermal Effect Limits in Ultrahigh-Density Magnetic Recording, IEEE Trans. Magn. 35, 4423 (1999).
Ikeda, S. et al. A perpendicular-anisotropy CoFeB–MgO magnetic tunnel junction. Nat. Mater. 9, 721 (2010).
Nakajima, N. et al. Perpendicular magnetic anisotropy caused by interfacial hybridization via enhanced orbital moment in Co/Pt multilayers: Magnetic circular x-ray dichroism study. Phys. Rev. Lett. 81, 5229 (1998).
Ishimatsu, N. et al. Orbital contribution to perpendicular magnetic anisotropy in Co80Pt20 thin films. J. Appl. Phys. 106, 033902 (2009).
Grange, W. et al. Experimental and theoretical x-ray magnetic-circular-dichroism study of the magnetic properties of Co 50 Pt 50 thin films. Phys. Rev. B 62, 1157 (2000).
Grange, W. et al. Magnetocrystalline anisotropy in (111) CoPt3 thin films probed by x-ray magnetic circular dichroism. Phys. Rev. B 58, 6298 (1998).
Zhang, W. et al. Magnetocrystalline anisotropy of magnetic grains in Co80Pt20:oxide thin films probed by x-ray magnetic circular dichroism, J. Appl. Phys. 109, 113920 (2011).
Suzuki, M. et al. Depth profile of spin and orbital magnetic moments in a subnanometer Pt film on Co. Phys. Rev. B 72, 054430 (2005).
Chiba, D. et al. Electrical control of the ferromagnetic phase transition in cobalt at room temperature. Nature Materials 10, 853 (2011).
Shimamura, K. et al. Electrical control of Curie temperature in cobalt using an ionic liquid film. Appl. Phys. Lett. 100, 122402 (2012).
Miron, I. M. et al. Current-driven spin torque induced by the Rashba effect in a ferromagnetic metal layer, Nature Materials 9, 230 (2010).
Shinjo, T. & Yamamoto, H. Large Magnetoresistance of Field-Induced Giant Ferrimagnetic Multilayers J. Phys. Soc. Jpn. 59, 3061 (1990).
Mosca, D. H. et al. Oscillatory interlayer coupling and giant magnetoresistance in Co/Cu multilayers. J. Mag. Mag. Mater. 94, L1 (1991).
Weber, W. et al. Magnetic switching in cobalt films by adsorption of copper. Nature 374, 788 (1994).
Parkin, S. S. P., Bhadra, R. & Roche, K. P. Oscillatory magnetic exchange coupling through thin copper layers. Phys. Rev. Lett. 66, 2152 (1991).
Yuasa, S., Nagahama, T. & Suzuki, Y. Spin-polarized resonant tunneling in magnetic tunnel junctions. Science 297, 234 (2002).
Thiyagarajah, N. et al. Effects of perpendicular anisotropy on the interlayer coupling in perpendicularly magnetized [Pd/Co]/Cu/[Co/Pd] [Pd/Co]/Cu/[Co/Pd] spin valves. Appl. Phys. Lett. 92, 062504 (2008).
Bruno, P. & Chappert, C. Ruderman-Kittel theory of oscillatory interlayer exchange coupling. Phys. Rev. B 46, 261 (1992).
Samant, M. G. et al. Induced spin polarization in Cu spacer layers in Co/Cu multilayers. Phys. Rev. Lett. 72, 1112 (1994).
Swaminathan, P. et al. Induced magnetism in Cu nanoparticles embedded in Co. Appl. Phys. Lett. 91, 202506 (2007).
Held, G. A. et al. X-ray magnetic circular dichroism study of the induced spin polarization of Cu in Co/Cu and Fe/Cu multilayers. Z. Phys. B 100, 335 (1996).
Ebert, H. et al. L-edge x-ray absorption in fcc and bcc Cu metal: Comparison of experimental and first-principles theoretical results. Phys. Rev. B 53, 16067 (1996).
Ohkochi, T., Hosoito, N., Mibu, K. & Hashizume, H. Induced magnetic polarization in Cu layers of Gd/Cu multilayers studied by x-ray magnetic circular dichroism. J. Phys. Soc. Jpn. 73, 2212 (2004).
Bandiera, S., Sousa, R. C., Rodmacq, B. & Dieny, B. Enhancement of perpendicular magnetic anisotropy through reduction of Co-Pt interdiffusion in (Co/Pt) multilayers. Appl. Phys. Lett. 100, 142410 (2012).
Bandiera, S. et al. Effect of a Cu spacer between Co and Pt layers on the structural and magnetic properties in (Co/Cu/Pt)5/Pt type multilayers. J. Phys. D: Appl. Phys. 46, 485003 (2013).
Stohr, J. Exploring the microscopic origin of magnetic anisotropies with X-ray magnetic circular dichroism (XMCD) spectroscopy. J. Mag. Mag. Mater. 200, 470 (1999).
Bruno, P. Tight-binding approach to the orbital magnetic moment and magnetocrystalline anisotropy of transition-metal monolayers. Phys. Rev. B 39, 865 (1989).
Andersson, C. et al. Influence of ligand states on the relationship between orbital moment and magnetocrystalline anisotropy. Phys. Rev. Lett. 99, 177207 (2007).
Kota, Y. & Sakuma, A. Relationship between magnetocrystalline anisotropy and orbital magnetic moment in L10-type ordered and disordered alloys. J. Phys. Soc. Jpn. 81, 084705 (2012).
Solovyev, I. V., Dederichs, P. H. & Mertig, I. Origin of orbital magnetization and magnetocrystalline anisotropy in TX ordered alloys (where T = Fe, Co and X = Pd, Pt). Phys . Rev. B 52, 13419 (1995).
Bartolomé, J. et al. Magnetic polarization of noble metals by Co nanoparticles in M-capped granular multilayers (M = Cu, Ag, and Au): An x-ray magnetic circular dichroism study. Phys Rev. B 77, 184420 (2008).
van der Laan, G. Microscopic origin of magnetocrystalline anisotropy in transition metal thin films. J. Phys.: Condens. Matter 10, 3239 (1998).
Koyama, T., Obinata, A., Hibino, Y. & Chiba, D. Sign reversal of electric field effect on coercivity in MgO/Co/Pt system. Appl. Phys. Express 6, 123001 (2013).
Koyama, T. et al. Dependence of Curie temperature on Pt layer thickness in Co/Pt system. Appl. Phys. Lett. 106, 132409 (2015).
Koide, T. et al. Direct determination of interfacial magnetic moments with a magnetic phase transition in Co nanoclusters on Au(111). Phys. Rev. Lett. 87, 257201 (2001).
Kresse, G. & Hafner, J. Ab initio molecular dynamics for liquid metals. Phys. Rev. B 47, R558 (1993).
Kresse, G. & Furthmuller, J. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set. Phys . Rev. B 54, 11169 (1996).
Perdew, J. P., Burke, K. & Ernzerhof, M. Generalized gradient approximation made simple. Phys. Rev. Lett. 77, 3865 (1996).
This work was partly supported by a Grant-in-Aid for Scientific Research (B) (Grant No. 15H03562) and (S) (Grant Nos 25220604, 16H06332) from the Japan Society for the Promotion of Science and Spintronics Research Network of Japan. Synchrotron radiation experiments were performed under the approval of the Photon Factory Program Advisory Committee, KEK (Nos 2013G195, 2015G090) and the Japan Synchrotron Radiation Research Institute (JASRI, SPring-8, 2014B1853 and 2015A0117).
The authors declare no competing financial interests.
About this article
Cite this article
Okabayashi, J., Koyama, T., Suzuki, M. et al. Induced perpendicular magnetization in a Cu layer inserted between Co and Pt layers revealed by x-ray magnetic circular dichroism. Sci Rep 7, 46132 (2017). https://doi.org/10.1038/srep46132
Critical role of orbital hybridization in the Dzyaloshinskii-Moriya interaction of magnetic interfaces
Communications Physics (2022)
Hyperfine Interactions (2021)
Scientific Reports (2018)