Waveguide amplifiers have always been significant key components for optical communication. Unfortunately, the low concentration of rare earth ions doped in the host material and the inadequate optimization of the waveguide structure have been the common bottleneck limitations. Here, a novel material, NaYF4/NaLuF4: 20% Yb3+, 2% Er3+ nanoparticle-Polymeric Methyl Methacrylate covalent-linking nanocomposite, was synthesized. The concentrations of Er3+ and Yb3+ doping increased an order of magnitude. Under a 980 nm laser excitation, highly efficient emission at 1.53 μm was obtained. The characteristic parameters of the single mode waveguide were carefully designed and optimized by using a finite difference method. A formulized iteration method is presented for solving the rate equations and the propagation equations of the EYCDWA, and both the steady state behavior and the gain were numerically simulated. The optimal Er3+ and Yb3+ concentrations are 2.8 × 1026 m−3 and 2.8 × 1027 m−3, and the optimal waveguide length is 1.3 cm. Both theoretical and experimental results indicated that, for an input signal power of 0.1 mW and a pump power of 400 mW, a net gain of 15.1 dB at 1530 nm is demonstrated. This result is the highest gain ever reported in polymer-based waveguide amplifiers doped with inorganic Er3+-Yb3+ codoped nanocrystals.
In the past two decades, erbium-doped fiber amplifiers have been extraordinarily successful because the infrared emission wavelength of the Er3+ ion corresponds to the low-loss telecommunication window in the wavelength range approximately 1530 nm in optical communication1,2,3. With continued progress in information technology, the miniaturization of such fiber amplifiers is of considerable interest for the development of on-chip photonic integration and chip-scale optical communication. The continuous decrease in both size and cost has provided a motivation for utilizing erbium-doped waveguide amplifiers (EDWAs)4. EDWAs can be integrated with other optical devices, such as splitters, couplers, and switches as active integrated optical waveguide devices networks, which have important applications in optical communication, phase array antennas, optical computers, and optical systems. Erbium-doped waveguide amplifiers could offer a unique highly integrated optical signal processing platform with benefits of low loss, compact, flexible design of optical properties, and cost-effective features for high density integrated devices5,6. Various materials have been investigated to fabricated EDWAs, including Er3+ doped in Al2O37,8, Y2O3, LiNbO3 crystal9,10, phosphate glass11, and polymeric materials12. Compared with the other hosts, organic polymers are exemplary, with their excellent properties in terms of simple processing, low-cost, high bandwidth, and good thermal stability13,14.
EDWAs have recently received considerable attention as a potential high-gain medium for optical amplification in the communication band. To increase the absorption cross section, ytterbium ions (Yb3+) are usually codoped as a sensitizer. Er3+-Yb3+ codoped waveguide amplifiers (EYCDWAs) are therefore expected to be an attractive high-gain medium material for optical amplification15,16,17,18. With the development of optical communication, optical waveguide amplifiers with high gain are required urgently. In particular, according to the current reports, developments in the net gain are expected. Anh Quoc Le Quang et al. fabricated an EDWA based on erbium-complex-doped Polymeric Methyl Methacrylate (PMMA) thin films and demonstrated a net gain of 1.34 dB at 1540 nm for a 1.6 cm long single mode waveguide amplifier19. Er3+-Yb3+ doped ENR polymer optical amplifiers with optical gains approaching 4.85 dB/cm−1 were also reported20. Obviously, such characteristics do not meet the modern optical communications requirements; thus, the current efforts in improving the gain properties of the EYCDWAs are not sufficient. The low concentration and poor dispersion of the inorganic Er3+ and Yb3+ ions doped directly in organic polymeric matrices have become the bottleneck for progress. Simultaneously, more attention should be paid to optimize the device structures. In 2015, Tianjiao Wang et al. synthesized NaYF4:Er3+, Yb3+ NPs-PMMA covalent-linking nanocomposites with core only using a high temperature thermal decomposition approach, and fabricated the waveguide amplifiers. A relative optical gain of 7.6 dB was obtained at 1540 nm in a 15 mm-long waveguide21. In this case, the doping mass concentration of NPs in the polymer matrix could be up to 1%, which is larger than previously published results. While their luminescence quantum yield was generally low due to nonradiative energy losses caused by the surface defects as well as from vibrational deactivation ascribed to solvent molecules and ligands adsorbed on the NPs. To overcome this deficiency, one effective strategy to improve the luminescence of NPs is the construction of core–shell architectures, where a shell is grown around the luminescent core with similar lattice constants.
In this paper, we report a new strategy to improve the dispersibility of nanoparticles (NPs) in a polymer matrix, in which the core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs were copolymerized with methyl methacrylate (MMA) and NPs-PMMA covalent-linking nanocomposites were synthesized. Using the NPs-PMMA covalent-linking nanocomposites as the core material, we constructed optical waveguide amplifiers with a structure of an embedded waveguide. A formulized iteration method is presented for solving the rate equations and the propagation equations of the EYCDWA under the conditions of uniform doping and both the steady state and the gain were numerically simulated. The characteristic parameters were optimized. The device was fabricated and characterized using the conventional semiconductor processes. A comparison of the experimental results with the theoretical model is presented. Both simulation and analysis were performed for this material. For an input signal power of 0.1 mW and a pump power of 400 mW, a net gain of 15.1 dB at 1530 nm was demonstrated for waveguide lengths of 1.3 cm; the concentration of Er3+ was 2.8 × 1026 m−3 and the concentration of Yb3+ was 2.8 × 1027 m−3. This net gain result is the highest ever reported in polymer-based EYCDWAs containing erbium doped inorganic nanocrystals.
Results and Discussion
In our experiment, a novel type of active material, NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA, was synthesized. The core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs has not only improved the intensity of the 1.53 µm fluorescent band but also suppressed surface quenching. NaYF4/NaLuF4: Yb3+, Er3+ coated with oleic acid (OA) was synthesized using a mild hydrothermal method in a water-ethanol-OA mixed solvent system. The surface of NPs was modified by the unsaturated functional groups. Next, these NaYF4/NaLuF4: Er, Yb NPs were copolymerized with methyl methacrylate (MMA), and then the NPs-PMMA covalent-linking nanocomposites were synthesized. Distinguished from the physical doping, this novel material has a higher concentration of dopant and its performance is more stable. Under 980-nm laser excitation, highly efficient emission at 1.53 μm was obtained.
Taking into account the high concentrations of dopant in the NaYF4/NaLuF4:Yb3+, Er3+ NPs-PMMA films, it is very difficult to directly etch the film to form rib or rectangular waveguides. Therefore, we choose the embedded waveguide as the structure. The cross-section view of the waveguide is shown in Fig. 1(a). The NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA was used as a core, and the PMMA was used as a cladding. The refractive index of the core and upper cladding were measured using an ellipsometry method (J. A. Woollam., Co.M2000). The measured values of the core layer were 1.49 and 1.5001 at 1530 nm and 980 nm, respectively. The refractive indices of the cladding were 1.478 and 1.486 at 1530 nm and 980 nm, respectively. The dimension of the waveguide and the refractive index of the core layer and cladding often determine the single-mode confinement condition. Signal-mode field22 simulations at the pump and signal wavelengths were conducted using the finite difference method (FDM). The relations based on the eigenvalue equations between the core thickness band mode effective refractive indices Neff of the rib waveguide are shown in Fig. 1(b), where the waveguide width a = 1.5b and the rib height h = 0.7b. As visible, we can realize single-mode propagation of the mode when b was between 0 and 3 μm at 980 nm and 0 to 5 μm at 1530 nm realize in the rib waveguide. b = 5 μm (a = 7.5 μm and h = 3.5 μm) was chosen as the total core thickness. Figure 1(c) shows the optical field distribution at 1530 nm of this size of waveguide calculated using the beam propagation method (BPM).
Optimization of the parameters of the waveguide is very important. To achieve a more accurate simulation of the gain characteristics, it is necessary to consider as many levels as possible of the Er3+–Yb3+ co-doped systems shown in Fig. 2(a). The upconversion effect between erbium ions and the cross relaxation effect between erbium-ytterbium ions were considered. The operation principle of the EYCDWA is described as follows. Yb3+ ions are excited by the pump light from the ground state 2F7/2 to the excited state 2F5/2, followed by the transfer energy to the nearby ground state Er3+ ions 4I15/2. Next, these Er3+ ions are excited to the excitation level 4I11/2. Because the excitation level 4I11/2 is unstable, Er3+ ions quickly decay to the metastable level 4I13/2. Meanwhile, upconversion occurs between two Er3+ ions from the signal level 4I13/2 to both 4I9/2 and 4I15/2. Population inversion occurs from 4I13/2 to 4I15/2, followed by relaxation to the ground level 4I15/2 via emission of photons, the frequency of which is the same as that of the signal; thus, the device achieves amplification of the signal. Here, the amplified spontaneous emission was neglected. Therefore, the rate equations were established and then solved using a formulized iteration method. Combining the signal and the pump propagation equations, the gain characteristics were analyzed using the Runge-Kutta method under the conditions of the uniform doping and the steady state. The gain G was defined as follows23,24:
The gain curves were simulated accordingly. Figure 2(b) shows the gain versus coordinate pump power at 980 nm for different overlapping factors. The overlap integral factor plays a decisive role on the gain. The formula is given as follows25:
where ΓP and ΓS are the overlap factors of the pump and the signal, respectively. A is the area of the cross-section of the waveguide core. Figure 2(b) shows that as the overlap integral factors increase, the gain increases and then saturates at the pump power of 400 mW. When the overlap factors change from 0.8 to 0.9, the gain does not change significantly. The overlap factors of the embedded waveguide with the size we designed are 0.848 at the signal wavelength and 0.87 at the pump wavelength. The overlap factors change to different waveguide cross-section dimensions. The simulation results shown above indicate that the gain highly depends on the overlapping factors related to the waveguide cross-section dimensions. The results provide further verification that the dimensions of the waveguide cross-section we designed are valid and that the pump power is sufficient.
Based on the above analysis, we choose 400 mW as the pump power because the gain curve tends to saturation around this level. Thus, the erbium ion concentration and the waveguide length are optimized. Figure 2(c) shows the gain versus Er3+ concentration NEr for different waveguide lengths. Figure 2(c) indicates that as the Er3+ concentration increases, the gain increases to a maximum. The Er3+ concentration corresponding to the maximum gain is called the optimal Er3+ concentration, which has different values under different waveguide lengths. When the length of the waveguide increases from 1 cm to 4 cm, the gain corresponding to the optimal Er3+ concentration also increases. Moreover, for the length of the waveguide of 5 cm, the gain decreases under the pump power of 400 mW. Therefore, to obtain high gain, the Er3+ concentration cannot be excessively high. Its, value can be chosen in the range of 1.6–2.8 × 1026 m−3 for the waveguide length of 1–2 cm. The optimal Er3+ concentration is 2.8 × 1026 m−3 with waveguide length of approximately 2 cm. The gain of which is 35 dB. Ytterbium ions codoped as a sensitizer can increase the concentration of Er3+ to prevent quenching. Thus, the Yb3+ concentration has a substantial impact on the gain. For the pump power of 400 mW, the Er3+ concentration is 2.8 × 1026 m−3 and the waveguide length is 2 cm, and then the Yb3+ concentration is optimized. The gain versus Yb3+ concentration NYb curves for different pump powers are shown in Fig. 2(d). Figure 2(d) indicates that the gain increases with the pump power increasing. As the Yb3+ concentration increases, the gain increases to a maximum and then decreases. The optimal Yb3+ concentration is 2.8 × 1027 m−3 under the 400 mW pump power. From the above analysis we obtained the optimized waveguide range of 1–2 cm; to obtain an optimized value of the waveguide length accurately, the gain versus waveguide length for different pump powers were simulated, as shown in Fig. 2(e). We know from Fig. 2(e) that as the pump power increases, the maximum gain also increases. As the waveguide length increases, the gain increases to a maximum and then decreases. The waveguide length corresponding to the maximum gain is called the optimal waveguide length, which has different values for different pump powers. When the pump power is 400 mW, the optimal waveguide length is 1.3 cm. All the optimal parameters from the above analysis are summarized in Table 1.
Comparison of the experimental results with the simulation
The NaYF4/NaLuF4:Yb3+, Er3+ NPs-PMMA was used as a core, and the PMMA was used as the cladding. The dimensions of the waveguide were determined by the above simulation. The width of the groove is 7.5 μm, and the depth is 3.5 μm. We used conventional semiconductor processes to fabricate the embedded waveguide. Figure 3 shows the scanning electron microscopy (SEM) micrograph of the cross-section of a groove. The ridge wall is smooth and almost vertical. The width of the groove is 7.7 μm, and the depth of the groove is 3.8 μm. These dimensions are basically consistent with the dimensions we designed. The thickness of the upper cladding and the under cladding is 3 μm and 7 μm, respectively.
The propagation losses of the waveguide amplifier were measured by the cut-back method26. The cutback method relies on assuming identical fiber-to-waveguide coupling conditions and comparing the losses at1530 nm through waveguides of different lengths in the same waveguide, as shown integrated radially in Fig. 4(a). A linear fit to the experimental data is shown as a continuous line, and its slope provides the propagation-loss coefficient in dB/cm. The propagation loss is approximately 5.3 ± 0.3 dB/cm at 1530 nm. This value is relatively high because the absorption cross-section of the Er3+ is high, and the corresponding strong absorption was considered in the simulation. The gain characteristics of the EYCDWA were tested. Figure 4(b) shows the measured data and the simulated curve as a function of pump power at 980 nm in a 1.3-cm long waveguide. The solid line shows the simulated results based on the theoretical models, and the solid square dots are the measured data. When the input signal power was 0.1 mW and the pump power was 400 mW, a high relative gain of 29.2 dB at 1530 nm was achieved. Compared with the simulated result, the measured data were close to the theoretical estimates. Figure 4(c) shows the tested sample of waveguide amplifiers for the optical gain measurement. Under 980-nm laser excitation, a clear green light from the phenomenon of upconversion occurs, which we have considered the upconversion in our above models. Next, the total insertion losses were measured to estimate the coupling loss immediately after each gain measurement. Because the launching and collecting fibers have exactly the same characteristics for the gain measurements and index-matching-fluid (diphenyl ether) was used in between the fiber and waveguide facets during all the experiments, it was assumed that similar coupling efficiencies were achieved in both the input and output ports. The coupling loss calculated by subtracting the previously determined propagation loss from the total insertion loss was approximately 3.6 dB per facet. Subtracting the propagation loss and the coupling loss, a net gain of 15.1 dB was achieved in a 1.3-cm long waveguide. Polymer optical waveguide amplifiers based on NaYF4/NaLuF4: 20% Yb3+, 2% Er3+ NPs-PMMA covalent-linking nanocomposites with 15.1 dB net gain is the highest net gain ever reported for polymer optical waveguide amplifiers doped with nanocrystals. But there is still a difference between the obtained results and the simulated amplifier performance. One of the reasons was the large coupling loss of the end faces. The large coupling loss could lead to the small power of the signal light and pump light coupled into the waveguide. Even though the coupling loss was subtracted in the simulated results, the small power of the signal light and pump light could decreased the gain. Besides, the ridge wall in simulation was more smooth and vertical than the waveguide fabricated. Then the propagation loss of the waveguide was larger than theoretical simulation. In addition, the fabrication tolerances can also result in the difference.
In conclusion, we designed an EDWA with a structure of an embedded waveguide using the NaYF4/NaLuF4: 20% Yb3+, 2% Er3+ NPs-PMMA covalent-linking nanocomposite as the core material. The concentrations of Er3+ and Yb3+ doping increased by an order of magnitude. Under 980-nm laser excitation, highly efficient emission at 1.53 μm was obtained. The characteristic parameters of the single mode waveguide were carefully designed and optimized using a finite difference method. A formulized iteration method was presented for solving the rate equations and the propagation equations of the EYCDWA under the conditions of uniform doping, and both the steady state behavior and the gain were numerically simulated. The optimal Er3+ and Yb3+ concentration is 2.8 × 1026 m−3 and 2.8 × 1027 m−3, respectively, and the optimal waveguide length is 1.3 cm. Both theoretical and experimental results indicated that, for an input signal power of 0.1 mW and a pump power of 400 mW, a net gain of 15.1 dB at 1530 nm is demonstrated for waveguide lengths of 1.3 cm. This result is the highest net gain ever reported in polymer-based on Er3+-Yb3+ codoped waveguide amplifiers doped inorganic nanocrystals.
We use the conventional semiconductor processes of spin-coating, standard photolithography and inductively coupled plasma (ICP) etching technology to fabricate the EYCDWA. Figure 5 shows a complete fabrication process diagram. A 7-μm-thick PMMA film was first spin-coated onto a 2-μm-thick silicon dioxide layer based on silicon substrate as the bottom cladding layer and then baked at 120 °C for 2 h. On the cladding layer, the standard pattern exposure was performed at a wavelength of 365 nm using the 350 mW Hg lamp through a contact chromium mask. And ICP etching technique was operated using oxygen. Then the NaYF4/NaLuF4:Yb3+, Er3+ NPs-PMMA was embedded into the grooves to form the core waveguides via spin-coating, and then the device was baked at 120 °C for 2 h. Finally, a 3-μm-thick PMMA film was spin-coated as the upper cladding and then baked at 120 °C for 2 h.
Figure 6 shows a schematic of the experimental setup for the optical gain measurement. The relative gain of the waveguide amplifiers was performed by using a tunable laser source (Santec TSL-210) with working wavelength range of 1510 nm to 1590 nm as the signal source and a 976 nm continuous wave laser diode as the pump source, with an output power of 400 mW. Signal and pump light were launched into the channel waveguides by a 976/1535 nm wavelength division multiplexing (WDM) coupler. A polarization controller was used to guarantee the input light was operated under TM mode. The output light from the device was collected and coupled to an optical spectrum analyzer (OSA, Ando AQ-6315A). Next, the relative gain was calculated via a computer using formula 14, where Ps(z) is the output signal power amplified by the waveguide, and Ps(0) is the input signal power.
How to cite this article: Zhang, M.L. et al. High-gain polymer optical waveguide amplifiers based on core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA covalent-linking nanocomposites. Sci. Rep. 6, 36729; doi: 10.1038/srep36729 (2016).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Wong, W. H. et al. Ultraviolet direct printing of rare-earth-doped polymer waveguide amplifiers. Appl. Phys. Lett. 87, 011103 (2005).
Bo, S. et al. LaF3: Er,Yb doped sol–gelpolymeric optical waveguide amplifiers. Appl. Phys. B 91,79–83 (2008).
Ye, H. Q. et al. Organo-erbium systems for optical amplification at telecommunications wavelengths. Nature Mater . 13, 382–386 (2014).
Jonathan, D. B. et al. Erbium implanted thin film photonic materials. Laser Photonics Rev . 5, 368–403 (2011).
Zheng Y. et al. Metal-cladding directly defined active integrated optical waveguide device based on erbium containing polymer. RSC Adv. 6, 3224–3230 (2015).
Yi Y. J. et al. Multilayer Hybrid Waveguide Amplifier for Three-Dimension Photonic Integrated Circuit IEEE Photonic Tech l . 27, 2411–2413 (2015).
Bradley, J. D. B. et al. Gain bandwidth of 80 nm and 2dB/cm peak gain in Al2O3:Er3+ optical amplifiers on silicon. J. Opt. Soc. Am. B 27, 187–196 (2010).
Hoven, G. N. et al. Upconversion in Er-implanted Al2O3 waveguides. J. App. Phys . 79, 1258–1266 (1996).
Huang, C. H. & McCaughan, L. 980 nm-pumped Er- doped LiNbO3 waveguide amplifiers: a comparison with 1484-nm pumping. J. Sel. Top. Quant. Electron 2, 367–372 (1996).
Huang, C. H. & McCaughan, L. Photorefractive-damage-resistant Er-indiffused MgO: LiNbO3 ZnO-waveguide amplifiers and lasers. Electron. Lett. 33, 1639–1640 (1997).
Zhao, R. T. et al. Bent channel design in buried Er3+/Yb3+ codoped phosphate glass waveguide fabricated by field-assisted annealing. Opt. Eng. 50, 04460 (2011).
Kumar, G. A. et al. Chalcogenide-bound Erbium complexes: paradigm molecules for infrared fluorescence emission. J. Chem. Mater. 17, 5130–5135 (2005).
Liu, Y. F. et al. Improved performance of thermal-optic switch using polymer/silica hybrid and air trench waveguide structures. Opt. Lett. 40, 1888–1891 (2015).
Zhao, P. C. et al. Optical amplification at 1525 nm in BaYF5:20% Yb3+, 2%Er3+ nanocrystals doped SU-8 polymer waveguide. J. Nanomater. 153028 (2014).
Vázquez-Córdova, S. A. et al. Erbium-doped spiral amplifiers with 20 dB of net gain on silicon. Opt. Express 22, 25993–26004 (2014).
Chen, C. et al. Erbium-ytterbium codoped waveguide amplifier fabricated with solution-processable complex. J. Appl. Phys. Lett. 94, 041119 (2009).
Liu, X. Y. et al. NaYF4 Nanocrystals with Intense 1530 nm Fluorescence for Polymer Optical Waveguide Amplifiers. J. Nanosci. Nanotechnol. 14, 3499–3502 (2014).
Zhai X. S. et al. Enhancement of 1.53 μm emission band in NaYF4: Er3+, Yb3+, Ce3+ nanocrystals for polymer-based optical waveguide amplifiers. Opt. Mater. Express 3, 270–277 (2013).
Le Quang A. Q. et al. Demonstration of net gain at 1550 nm in an erbium-doped polymer single mode rib waveguide. Appl. Phys. Lett. 89, 141124 (2006).
Pun, E. Y. B. & Wong, W. H. City University of Hong Kong, Doped polymeric optical waveguide amplifiers. United States Patent US 7,826,133 B2 (2010).
Wang, T. J. et al. Optical waveguide amplifiers based on NaYF4:Er3+,Yb3+ NPs-PMMA covalent-linking nanocomposites. Opt. Mater. Express 5, 469–478 (2015).
Wang, X. B. et al. 650-nm 1 × 2 polymeric thermo-optic switch with low power consumption. Opt. Express 22, 11119–11128 (2014).
Liao, J. K. et al. Polarization dispersion characteristics analysis of optical rib wave-guides in organic/polymer photonic devices. Opt. Commun. 350, 241–247 (2015).
Li, T. et al. Gain Characteristics of LaF3:Er, Yb Nanoparticle-Doped Waveguide Amplifier. J. Nanosci. Nanotechnol. 11, 9409–9414 (2011).
Zhao, P. C. et al. Gain and noise characteristics of phosphate glass Er3+–Yb3+ co-doped waveguide amplifiers. Opt. Quant. Electron. 46, 153028 (2014).
Bradley J. D. B. et al. Fabrication of low-loss channel waveguides in Al2O3 and Y2O3 layers by inductively coupled plasma reactive ion etching. Appl. Phys. B 89, 311–318 (2007).
This work was supported by the National Natural Science Foundation of China (Nos 61475061, 61405070 and 61575076) and the Science and Technology Development Plan of Jilin Province (No. 20140519006JH).
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhang, M., Zhang, W., Wang, F. et al. High-gain polymer optical waveguide amplifiers based on core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA covalent-linking nanocomposites. Sci Rep 6, 36729 (2016). https://doi.org/10.1038/srep36729
This article is cited by
Anti-escaping of incident laser in rare-earth doped fluoride ceramics with glass forming layer
Scientific Reports (2019)
Polymer-Silica Hybrid On-Chip Amplifier with Vertical Pumping Method
Scientific Reports (2018)
Low Loss Nanostructured Polymers for Chip-scale Waveguide Amplifiers
Scientific Reports (2017)
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.