Abstract
Subwavelength structural color filtering and printing technologies employing plasmonic nanostructures have recently been recognized as an important and beneficial complement to the traditional colorant-based pigmentation. However, the color saturation, brightness and incident angle tolerance of structural color printing need to be improved to meet the application requirement. Here we demonstrate a structural color printing method based on plasmonic metasurfaces of perfect light absorption to improve color performances such as saturation and brightness. Thin-layer perfect absorbers with periodic hole arrays are designed at visible frequencies and the absorption peaks are tuned by simply adjusting the hole size and periodicity. Near perfect light absorption with high quality factors are obtained to realize high-resolution, angle-insensitive plasmonic color printing with high color saturation and brightness. Moreover, the fabricated metasurfaces can be protected with a protective coating for ambient use without degrading performances. The demonstrated structural color printing platform offers great potential for applications ranging from security marking to information storage.
Similar content being viewed by others
Introduction
Plasmonic metasurfaces1,2,3,4,5,6 have emerged as an exciting class of subwavelength architectures that exhibit extraordinary enhancement and confinement of optical fields with well-controlled intensity, phase and polarization of light beyond the diffraction limit7,8,9. By appropriately adjusting the structural geometries of metasurfaces, the plasmonic resonances of metasurfaces can be tuned from the visible regime through the infrared, serving as the foundation of many fascinating applications such as biochemical sensing10,11, photovoltaic solar cells12, optical imaging13 and color filtering14,15,16,17. Structural color printing based on plasmonic metasurfaces not only provides a much higher (about two-orders of magnitude) printing spatial resolution18 but also gives an attractive approach with reduced number of the needed materials19, compared to the traditional pigment-based color printing. Besides, structural color printing also has the advantages of lower cost, easier recycling and higher reproduction fidelity and stability20.
Recently several strategies have been employed to realize structural colors, including interference effects induced by dielectric single layer21 or multilayers22, extraordinary optical transmission23 based plasmonic color filters14,24,25,26 and various kinds of plasmonic resonators above metallic reflectors15,20,27,28,29. Despite their potentials as next-generation color-printing technologies, however, the color printing performance of the previously reported approaches are limited by several factors, which will hinder their usage in practical applications. From the respect of materials used, for example, the interband transitions of gold limit the rendering of colors at wavelengths less than around 500 nm20,30 and the uncoated silver structures are susceptible to oxidation and sulphidation which may degrade the colors29. While aluminum nanostructures affords longer stability benefiting from impermeable natively coated oxide layer18,19,30,31,32,33, the higher loss of aluminum in the visible regime is a drawback for the color printing due to the fact that plasmonic resonances with broad bandwidth and low intensity contrast decrease severely the color brightness and saturation (or purity)18,19,24,25,26. From the respect of structures adopted, for example, reflection configurations based on localized plasmonic resonances exhibit weak angular dependence19 but suffer from the relatively large radiative damping due to low quality factor (Q-factor) dipolar resonances18,19,27. In general, in the existing approaches, plasmonic resonances with broad resonance peaks and low optical intensity contrasts significantly limit the performance of structural color printing.
For practical color printing applications where a high color brightness and saturation are preferred, it is necessary to achieve color filtering with low cross-talk25 and reasonably high optical reflection efficiency for three primary colors (cyan-magenta-yellow, CMY system). To meet this end, in this paper a simple but efficient structural color printing platform is introduced based on plasmonic metasurface with a thin-layer metal-dielectric-metal (MIM) structure, by which pure perfect absorption resonances with high Q-factor are tailored throughout the entire visible frequency range. Here silver is selected as the metallic material due to its low absorption loss in visible frequencies so that relatively sharper plasmonic resonances can be obtained for achieving better color saturation which is desirable in practical color printing applications. As a mechanical protection layer is always desired for use in exposed ambient color printing applications, the issues of oxidation and sulphidation of silver can be readily solved by coating the metasurface with a thin transparent polymer overlayer without significantly influencing the color performance. The resonance wavelength redshift induced by the polymer layer can be easily compensated by the geometrical adjustment.
Results
Plasmonic metasurfaces of perfect light absorption for color printing
Figure 1(a) illustrates the schematic diagram of the proposed plasmonic metasurfaces of perfect absorption consisting of three functional layers, including the top 25 nm silver thin film and the bottom 100 nm silver mirror, which are separated by a 45 nm silica dielectric spacer. Circular hole arrays of triangular lattice with period P and hole radius r are patterned on the top silver film. Figure 1(b) shows a cross-sectional scanning electron micrograph (SEM) image of a selected metasurface with P = 320 nm and r = 90 nm. The presence of the bottom silver mirror totally eliminates the transmittance (T = 0) of the metasurface due to the small penetration depth in silver (~20 nm at visible frequencies). The bottom 100 nm silver is deposited with the electron-beam evaporation system on top of a silicon wafer and subsequent layers are deposited with Kurt Lesker sputterer. A 5 nm silica overlayer is deposited finally to protect the triple-layer structure from degradation in air. The dependence of optical absorption resonance on the thickness of either the dielectric spacer or the top silver layer is investigated numerically as shown in Supplementary Figure S1. The top silver layer is patterned with circular hole arrays of triangular lattice by using the focused ion beam (FIB) milling (FEI Helios Nanolab 600 DualBeam system). Highly confined surface-plasmon polaritons (SPPs) will be excited by the periodic holes on the top silver thin film while the intermediate dielectric spacer will function as a bridge to couple the SPPs on two metal-dielectric interfaces34 to form an optical magnetic dipole resonance11,35. The coexistence of electric dipole resonance and magnetic dipole resonance in the plasmonic metasurfaces will result in matched impedance to the free space, leading to perfect light absorption and negligible reflection36. Additionally, it has been suggested that the hole array of a triangular lattice has a larger wavelength interval between the first two plasmonic resonances compared to a square lattice at the same lattice period25,26, which means the metasurface with triangular-lattice hole array will reduce the color cross-talk between different plasmonic resonances and therefore produce a purer color. Each fabricated hole array has a structural footprint of 20 × 20 μm2 area which is sufficient for the optical reflection measurements. Representative SEM images of three metasurfaces with different geometrical parameters are shown in Fig. 1(c–e) and optical images obtained using bright-field microscope are shown in the insets. The SEM images reveal that the fabricated metasurfaces have well-defined circular holes with very low edge roughness. The optical images show a high degree of color saturation and homogeneity for bright colors of yellow, magenta and cyan, respectively.
The optical reflection spectra of the fabricated metasurfaces are characterized in the visible frequency range (400 −750 nm) with a home-built optical measurement system. At first the effects of the hole size on the optical absorption efficiency and color appearance are investigated. Seven metasurface structures consisting of triangular-lattice hole arrays with a constant period (P = 200 nm) but different hole radius (r = 45 −75 nm) are fabricated. Figure 2(a) gives the measured optical reflection spectra (red solid curves). As the hole radius increases from 45 to 75 nm in a 10-nm step, the absorption resonance wavelength is blue-shifted linearly from 527 to 473 nm and the full-width at half-maximum (FWHM) increases gradually, while the optical absorption at the resonance is always high. Especially, a narrow, near perfect absorption resonance (A ≈ 98%) is observed around the wavelength 520 nm for r = 50 −55 nm, which has a small FWHM of approximately 55 nm. Meanwhile, the corresponding optical image for each metasurface is shown as the inset along with the measured optical reflection curve. It is shown that the color changes gradually from bright magenta to orange as the hole radius increases from 45 to 75 nm. Note that such large absorption contrast within a narrow wavelength range leads to bright colors with high saturation. Numerical simulations (black solid curves) based on finite element method are used to identify the absorption resonance in the measured optical reflection spectra. Measured permittivities of silver and silica are employed in the simulations, resulting in a good agreement to the experimental results. The influence of different loss factors multiplied onto the imaginary part of the silver permittivity can be seen in Supplementary Figure S2.
In order to achieve a large tunable color range in the visible spectrum, the hole radius and lattice period are then varied simultaneously. Figure 2(b) shows the measured optical reflection spectra (red solid curves) with the period increases from 130 to 260 nm and the optimized hole radius from 35 to 65 nm. The unit cell with the period smaller than 300 nm is chosen here to reduce the influence of diffraction and to allow for wider viewing angles20. A rich color appearance is obtained as shown as the inset of each subfigure. Besides the bright magenta presented by the metasurface with 200 nm period shown in Fig. 2(a), another two primary colors of yellow and cyan as well as the intermediate colors between them are achieved by the metasurfaces with 130 nm period (top panel in Fig. 2(b)) and 260 nm period (bottom panel), respectively. All the simulated and measured optical reflection spectra have been converted to the CIE1931 chromaticity coordinates as shown in Fig. 2(c,d), illustrating the color gamut of the method. It is noticed that there are points all around the achromatic point, demonstrating the large degree of color range tuning ability19 and scaling property of the designed plasmonic metasurfaces.
High-resolution plasmonic color printing with high brightness and saturation
To demonstrate the suitability of the proposed metasurface platform and its visual performance in structural color printing related applications, the colored images of the athletics mark of Missouri University of Science and Technology are realized in Fig. 3. Both a miniature replication (51.6 × 33.3 μm2, Fig. 3(d)) of the original pattern and a more colorful image (Fig. 3(e)) are prepared. By choosing the appropriate lattice period and hole radius in each pixel, the desired image colors (green and yellow) are reproduced with high fidelity and visual homogeneity. Moreover, another four distinct colors (symbol ‘&’: orange, character ‘S, T’: magenta, pickaxe shape: cyan and word ‘MISSOURI’: navy blue) displayed in Fig. 3(e) reveal high purity, brightness and large visual contrast in the produced colored image, benefiting from the strong absorption resonance supported in the fabricated metasurfaces. Furthermore, it is shown that bright colors can be produced by a tiny area containing only two pixels (as small as about 300 nm in width shown in Fig. 3(d,e)) and distinct colors are well preserved even at the sharp corners and boundaries of neighboring areas, exhibiting the ultrahigh color printing resolution and a high degree of reproducibility. This color demonstration proves that the proposed structural color printing based on metasurfaces of perfect absorption is capable of creating high-resolution pixels with sizes beyond the optical diffraction limit.
Influence of protective polymer coating on the color printing
In order to illustrate the applicability and flexibility of the plasmonic color printing platform for ambient use, the metasurfaces are further protected by spin-coating a 100 nm thick poly(methyl methacrylate) (PMMA) layer from chemical degradation (oxidization, sulphidation) and mechanical damages (scratching, fingerprints). Figure 4 shows a direct comparison between three selected uncoated metasurfaces and the PMMA-coated ones, including both the measured (Fig. 4(a,b), related bright-field microscope images shown in the insets of each figure) and simulated (Fig. 4(c,d)) optical reflection spectra. The additional PMMA protection layer does have limited influence on the observed colors, where an increase of the effective refractive index of the surrounding material leads to an observable redshift of the absorption resonance wavelength and a corresponding color change with extracted CIE 1931 chromaticity coordinates shown in Fig. 4(e,f). It should be noted that although the addition of protective coating induces some broadening of the absorption resonance bandwidth due to a weaker confinement of the optical field in the dielectric spacer20 as compared to the uncoated metasurface (Fig. 4(g,h)), the optical resonance properties including both the absorption magnitude and the Q-factor are almost unchanged. As an example for the metasurface with period 200 nm and radius 45 nm (red solid curves in Fig. 4(a,b)), the measured optical absorption at the resonance wavelength increases from 94% to 98% and the Q-factor (defined as λres/FWHM) extracted from a Lorentz fitting decreases from 8.4 to 7.8, which are remarkable in plasmonic resonances37.
To further demonstrate the effect of PMMA coating on perceived color appearance, Fig. 5 shows the comparison of bright-field microscope images of color palettes for the uncoated metasurfaces and the PMMA-coated metasurfaces with hole radius between 25 −115 nm and period ranging from 120 to 360 nm, where more than 100 unique colors are included. It is shown that while the protective PMMA coating induces an influence on the perceived colors, there is no degradation of color brightness and saturation in the resultant color images. The gamut of the color palettes demonstrates that by appropriate design of hole size and lattice period, an ideal color production can be achieved with polymer protection20. Based on this idea, a structural color printed copy of a pastel painting from a public domain resource38 is fabricated in micrometer scale. For each color in the original painting shown in Fig. 5(c), an appropriate combination of lattice period and hole radius is selected to create the desired color by taking into account the influence of spectral redshift induced by the PMMA coating. The optical image of the PMMA-coated print reveals a high-quality color appearance (Fig. 5(e)) with a better color fidelity than the uncoated one (Fig. 5(d)). By taking the advantage of the high Q-factor of near perfect absorption of the metasurface structure, a relative broad color palette with high brightness and saturation is obtained by only changing the period and hole radius of the triangular lattices, without employing complicated color generation and mixing strategies such as in the case of aluminum color pixels18, where multiple nanostructures within a single pixel are included in order to compensate for the low Q-factor of the resonance. It is emphasized that the polymer-protected color printing method demonstrated here is well suited for practical applications, such as anti-counterfeit tag and security marking where color stability under mechanical or chemical influence is of paramount importance. As shown in Supplementary Figure S4, metasurfaces including three primary colors are exposed to ambient conditions for more than three months as a test of their durability and no signs of visible deterioration are observed.
Angle-insensitive light absorption and color printing
The angular dependence of the optical reflection spectral response of the metasurface is investigated numerically for a selected structure with P = 160 nm and r = 45 nm for both s-polarized (electric field parallel to y axis) and p-polarized (magnetic field parallel to y axis) light (Supplementary Figure S3). The angle resolved chromaticity coordinates have also been calculated from the obtained optical reflectance spectra. It is shown that although a small absorption resonance splitting due to the lattice period is observed at incident angles larger than 30°, the maximum absorption remains higher than 95% even at large incident angles (70°) under both polarizations. Although the excitation of SPPs via grating coupling inherently constitutes a limitation on the angle independence of the resonance wavelength, the effect of lattice period on the spectral response is less pronounced for the designed metasurfaces as compared to the single layer transmission color filters39 due to the following reasons. According to the optical field distribution at the resonance wavelength shown in Fig. 4(g) (uncoated metasurface) and 4(h) (PMMA-coated metasurface), a strong magnetic dipole resonance resulting from anti-symmetric current flow is introduced35 in the metasurface structure which is responsible for the observed perfect light absorption when the thickness of dielectric spacer is small40. The magnetic dipole resonance is expected to remain robust at large incident angles for both s-polarized and p-polarized light for the adopted triangular lattices. This expectation is confirmed by the numerically obtained angle-resolved optical reflection spectra shown in Supplementary Figure S3 (a,b) which exhibit high absorption at wide angle range. As a result, the colors of selected reflection spectral curves (Supplementary Figure S3 (d,e), retrieved from angle resolved chromaticity coordinates using a MATLAB code) are demonstrated to be stable under large viewing angles up to 70°.
Discussion
We have demonstrated the realization of high-performance structural color printing with high resolution, brightness and saturation by utilizing plasmonic metasurfaces of perfect light absorption. Due to the matched impedance to free space at the designated wavelength range, the metasurfaces present narrow-band and near unity absorption resonances in visible frequencies, yielding pure colors with high brightness and exhibiting in the meantime low dependences on polymer protection, incidence angles and polarizations. By simply scaling the period and hole radius of the triangular lattice in the metasurface design, wide color tunability across the entire visible frequency range has been achieved. We believe the demonstrated structural color printing platform based on the above plasmonic metasurfaces will open up the possibility of realizing high-performance, pigment-free color printing and relevant applications such as security marking and information storage.
Methods
Material deposition
The Ag-SiO2-Ag three-layer structure is deposited on top of a silicon wafer. The bottom 100 nm Ag layer is deposited using an electron-beam evaporator system. The SiO2 spacer and the top Ag layer are then deposited with sputtering method (Kurt J. Lesker), where Ag is deposited at the rate of 0.4 Å/sec and SiO2 is deposited at 0.2 Å/sec. The optical constant of both materials and the film thicknesses are characterized with the variable angle spectroscopic ellipsometry (VASE, J. A. Woollam Co. VB400/HS-190). The VASE measurements show that the optical constant of Ag matches the standard data of Johnson and Christy41 based on the fitting from a general oscillator model. The dielectric constant of SiO2 is fitted from the Cauchy dispersion relation.
Device fabrication
The triangular lattices of circular holes are patterned on the top of the first metallic layer of the MIM structure via a one-step focused ion beam milling (FEI Helios Nanolab 600 DualBeam) with a gallium ion current of 9.7 pA and an accelerating voltage of 30 KeV. Then a thin layer of PMMA (950-A2 in anisole, Michrochem), a commonly used positive electron-beam resist, is spin-coated (2,000 rounds per min) on top of the fabricated nanostructures. We choose PMMA in the present work due to its chemical and mechanical stability and the accurate control of the thickness via control of the spin speed or molecule concentration used. The thickness of the coated PMMA polymer layer is also determined through X-ray reflectivity (Philips X’Pert-MRD) measurement.
Optical characterization
We characterize the optical reflection spectra of all samples in the visible range (400 −750 nm) with a home-built optical measurement system. Halogen illumination is directed to the lattice area through a × 50 objective lens (numerical aperture of 0.42) and the reflected light from the metasurfaces is collected by the same objective lens and collimated through a pinhole defining the lattice area. Subsequently, the collected signal is directed to a fiber-coupled optical spectrometer (LR1, ASEQ instruments). The measured reflection spectra of all samples are then normalized by that of a silver coated mirror (THORLABS) which has optical reflection larger than 97.5% in the visible range.
Numerical simulations
Finite element method (FEM) simulations are performed to obtain the optical reflection spectra and field distributions using the software (COMSOL Multiphysics). In the simulations, periodic boundary conditions are employed along the x and y axes to account for the periodic arrangement of the unit cells. Perfectly matched layers (PMLs) surrounded by scattering boundary condition faces are utilized along the propagation direction (perpendicular to the planar metasurfaces) to avoid multiple reflections due to geometry truncation. Measured values of the permittivity of Ag (imaginary part multiplied by factor of 2 to account for surface irregularities and additional losses induced by fabrication) and SiO2 are employed in the simulations. Besides, finite-difference time-domain (FDTD) simulations are also carried out to check the results obtained by FEM method and to calculate the angle resolved reflection spectra shown in Supplementary Figure S3.
Additional Information
How to cite this article: Cheng, F. et al. Structural color printing based on plasmonic metasurfaces of perfect light absorption. Sci. Rep. 5, 11045; doi: 10.1038/srep11045 (2015).
References
Yu, N. et al. Light Propagation with Phase Discontinuities: Generalized Laws of Reflection and Refraction. Science 334, 333–337, 10.1126/science.1210713 (2011).
Ni, X., Emani, N. K., Kildishev, A. V., Boltasseva, A. & Shalaev, V. M. Broadband Light Bending with Plasmonic Nanoantennas. Science 335, 427, 10.1126/science.1214686 (2012).
Huang, L. et al. Three-dimensional optical holography using a plasmonic metasurface. Nat Commun 4, 10.1038/ncomms3808 (2013).
Mousavi, S. H. et al. Inductive Tuning of Fano-Resonant Metasurfaces Using Plasmonic Response of Graphene in the Mid-Infrared. Nano Letters 13, 1111–1117, 10.1021/nl304476b (2013).
Monticone, F., Estakhri, N. M. & Alù, A. Full Control of Nanoscale Optical Transmission with a Composite Metascreen. Physical Review Letters 110, 203903, 10.1103/PhysRevLett.110.203903 (2013).
Lin, D., Fan, P., Hasman, E. & Brongersma, M. L. Dielectric gradient metasurface optical elements. Science 345, 298–302, 10.1126/science.1253213 (2014).
Schuller, J. A. et al. Plasmonics for extreme light concentration and manipulation. Nat Mater 9, 368–368, 10.1038/nmat2630 (2010).
Kildishev, A. V., Boltasseva, A. & Shalaev, V. M. Planar Photonics with Metasurfaces. Science 339, 10.1126/science.1232009 (2013).
Yu, N. & Capasso, F. Flat optics with designer metasurfaces. Nat Mater 13, 139–150, 10.1038/nmat3839 (2014).
Adato, R. et al. Ultra-sensitive vibrational spectroscopy of protein monolayers with plasmonic nanoantenna arrays. Proceedings of the National Academy of Sciences 106, 19227–19232, 10.1073/pnas.0907459106 (2009).
Liu, N., Mesch, M., Weiss, T., Hentschel, M. & Giessen, H. Infrared Perfect Absorber and Its Application As Plasmonic Sensor. Nano Letters 10, 2342–2348, 10.1021/nl9041033 (2010).
Atwater, H. A. & Polman, A. Plasmonics for improved photovoltaic devices. Nature Materials 9, 205–213, 10.1038/nmat2629 (2010).
Kawata, S., Inouye, Y. & Verma, P. Plasmonics for near-field nano-imaging and superlensing. Nature Photonics 3, 388–394, 10.1038/nphoton.2009.111 (2009).
Xu, T., Wu, Y.-K., Luo, X. & Guo, L. J. Plasmonic nanoresonators for high-resolution colour filtering and spectral imaging. Nat Commun 1, 59, 10.1038/ncomms1058 (2010).
Wu, Y.-K. R., Hollowell, A. E., Zhang, C. & Guo, L. J. Angle-Insensitive Structural Colours based on Metallic Nanocavities and Coloured Pixels beyond the Diffraction Limit. Sci. Rep. 3, 10.1038/srep01194 (2013).
Zeng, B., Gao, Y. & Bartoli, F. J. Ultrathin Nanostructured Metals for Highly Transmissive Plasmonic Subtractive Color Filters. Sci. Rep. 3, 10.1038/srep02840 (2013).
Rajasekharan, R. et al. Filling schemes at submicron scale: Development of submicron sized plasmonic colour filters. Sci. Rep. 4, 10.1038/srep06435 (2014).
Tan, S. J. et al. Plasmonic Color Palettes for Photorealistic Printing with Aluminum Nanostructures. Nano Letters 14, 4023–4029, 10.1021/nl501460x (2014).
Clausen, J. S. et al. Plasmonic Metasurfaces for Coloration of Plastic Consumer Products. Nano Letters 14, 4499–4504, 10.1021/nl5014986 (2014).
Roberts, A. S., Pors, A., Albrektsen, O. & Bozhevolnyi, S. I. Subwavelength Plasmonic Color Printing Protected for Ambient Use. Nano Letters 14, 783–787, 10.1021/nl404129n (2014).
Kats, M. A., Blanchard, R., Genevet, P. & Capasso, F. Nanometre optical coatings based on strong interference effects in highly absorbing media. Nat Mater 12, 20–24, 10.1038/nmat3443 (2013).
Chung, K. et al. Flexible, Angle-Independent, Structural Color Reflectors Inspired by Morpho Butterfly Wings. Advanced Materials 24, 2375–2379, 10.1002/adma.201200521 (2012).
Ebbesen, T. W., Lezec, H. J., Ghaemi, H. F., Thio, T. & Wolff, P. A. Extraordinary optical transmission through sub-wavelength hole arrays. Nature 391, 667–669, 10.1038/35570 (1998).
Lee, H.-S., Yoon, Y.-T., Lee, S.-s., Kim, S.-H. & Lee, K.-D. Color filter based on a subwavelength patternedmetal grating. Opt. Express 15, 15457–15463, 10.1364/OE.15.015457 (2007).
Chen, Q. & Cumming, D. R. S. High transmission and low color cross-talk plasmonic color filters using triangular-lattice hole arrays in aluminum films. Opt. Express 18, 14056–14062, 10.1364/OE.18.014056 (2010).
Inoue, D. et al. Polarization independent visible color filter comprising an aluminum film with surface-plasmon enhanced transmission through a subwavelength array of holes. Applied Physics Letters 98, 093113, 10.1063/1.3560467 (2011).
Kumar, K. et al. Printing colour at the optical diffraction limit. Nat Nano 7, 557–561, 10.1038/nnano.2012.128 (2012).
Pors, A., Nielsen, M. G. & Bozhevolnyi, S. I. Broadband plasmonic half-wave plates in reflection. Opt. Lett. 38, 513–515, 10.1364/OL.38.000513 (2013).
Si, G. et al. Reflective plasmonic color filters based on lithographically patterned silver nanorod arrays. Nanoscale 5, 6243–6248, 10.1039/C3NR01419C (2013).
Zhang, J. et al. Continuous metal plasmonic frequency selective surfaces. Opt. Express 19, 23279–23285, 10.1364/OE.19.023279 (2011).
Yokogawa, S., Burgos, S. P. & Atwater, H. A. Plasmonic Color Filters for CMOS Image Sensor Applications. Nano Letters 12, 4349–4354, 10.1021/nl302110z (2012).
Qin, C. et al. CMOS Photodetectors Integrated With Plasmonic Color Filters. Photonics Technology Letters, IEEE 24, 197–199, 10.1109/LPT.2011.2176333 (2012).
Ellenbogen, T., Seo, K. & Crozier, K. B. Chromatic Plasmonic Polarizers for Active Visible Color Filtering and Polarimetry. Nano Letters 12, 1026–1031, 10.1021/nl204257g (2012).
Fang, Z., Zhen, Y.-R., Fan, L., Zhu, X. & Nordlander, P. Tunable wide-angle plasmonic perfect absorber at visible frequencies. Physical Review B 85, 245401, 10.1103/PhysRevB.85.245401 (2012).
Cai, W. et al. Metamagnetics with rainbow colors. Opt. Express 15, 3333–3341, 10.1364/OE.15.003333 (2007).
Cheng, F., Yang, X. & Gao, J. Enhancing intensity and refractive index sensing capability with infrared plasmonic perfect absorbers. Opt. Lett. 39, 3185–3188, 10.1364/OL.39.003185 (2014).
Melli, M. et al. Reaching the Theoretical Resonance Quality Factor Limit in Coaxial Plasmonic Nanoresonators Fabricated by Helium Ion Lithography. Nano Letters 13, 2687–2691, 10.1021/nl400844a (2013).
http://pixabay.com/en/art-frame-pastel-95850/. Free Illustration Art, Frame, Pastel - Free Image on Pixabay - 95850., (2012) Date of access: 23/02/2015.
Xu, T. et al. Structural Colors: From Plasmonic to Carbon Nanostructures. Small 7, 3128–3136, 10.1002/smll.201101068 (2011).
Wu, C. et al. Large-area wide-angle spectrally selective plasmonic absorber. Physical Review B 84, 075102, 10.1103/PhysRevB.84.075102 (2011).
Johnson, P. B. & Christy, R. W. Optical Constants of the Noble Metals. Physical Review B 6, 4370–4379, 10.1103/PhysRevB.6.4370 (1972).
Acknowledgements
The authors acknowledge the financial support from the University of Missouri Interdisciplinary Intercampus Research Program, the Ralph E. Powe Junior Faculty Enhancement Award and the National Science Foundation under grant CBET-1402743. The authors also acknowledge the facility support from the Materials Research Center at Missouri S&T. This work was performed, in part, at the Center for Integrated Nanotechnologies, an Office of Science User Facility operated for the U.S. Department of Energy (DOE) Office of Science. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-AC04-94AL85000.
Author information
Authors and Affiliations
Contributions
X.Y., J.G. and F.C. conceived the idea and designed the project. F.C. is responsible for the numerical simulation, device fabrication and optical measurement. T.L. is responsible for the deposition of metal and dielectric layers. X.Y. and J.G. directed the project. All authors discussed the results and contributed to the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Electronic supplementary material
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Cheng, F., Gao, J., Luk, T. et al. Structural color printing based on plasmonic metasurfaces of perfect light absorption. Sci Rep 5, 11045 (2015). https://doi.org/10.1038/srep11045
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep11045
This article is cited by
-
Cost-Effective and Environmentally Friendly Mass Manufacturing of Optical Metasurfaces Towards Practical Applications and Commercialization
International Journal of Precision Engineering and Manufacturing-Green Technology (2024)
-
Nanoscale modeling of dynamically tunable planar optical absorbers utilizing InAs and InSb in metal-oxide-semiconductor–metal configurations
Discover Nano (2023)
-
Electrically programmable solid-state metasurfaces via flash localised heating
Light: Science & Applications (2023)
-
A novel plasmonic metal–semiconductor–insulator–metal (MSIM) color sensor compatible with CMOS technology
Scientific Reports (2023)
-
Flash-Induced High-Throughput Porous Graphene via Synergistic Photo-Effects for Electromagnetic Interference Shielding
Nano-Micro Letters (2023)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.