Introduction

Recently, GaN-based materials have attracted much interest as a material suitable for use in optoelectronic and electronic devices due to their excellent properties1,2,3. However due to the immature GaN freestanding substrate technology, current commercial GaN-based devices are fabricated by epitaxy onto foreign substrates. The large lattice mismatch and difference in thermal expansion coefficient between the substrate and the layer results in high defect density (107–1010/cm2), which degrades its optical and electrical properties4,5,6. Thus, freestanding GaN wafers are in urgent need. Hydride vapor phase epitaxy (HVPE) is supposed to be the most promising method to acquire freestanding GaN with the advantages of simple equipment, low cost and quick growth speed7. GaN bulk growth using HVPE is started in most cases on c-oriented Al2O3 substrates. Due to the high lattice mismatch (13.8%), a high dislocation density is formed. In order to improve the crystal quality of GaN film, SiC is considered to be promising substrate material because of small lattice match (3.4%) and similar thermal expansion coefficient. GaN grown on SiC instead of sapphire has better crystal quality and smaller residual stress8. Several papers about the direct growth of GaN layers on Si- face SiC substrates by HVPE9 have been reported. However, there have been few papers about the direct growth of GaN layers on C-face SiC substrates by HVPE as the growth of high quality GaN on C- face SiC is much more difficult10.

In this paper, we successfully obtained high quality, stress-free GaN layer which directly self-separated from the SiC substrate. This method avoids ex situ processing to separate GaN layer from substrate before or after the growth. This is very different from the ones reported before such as mechanical lapping of sapphire11, laser lift-off12, chemical etching13, void assisted separation14 and ELOG15. Moreover, due to the small interaction stress between GaN and the SiC substrate, the SiC substrate was excellent without damage after the whole process so that it can be repeatedly used in the GaN growth.

Experimental

The growth was done in a home-built vertical HVPE reactor at atmospheric pressure. The precursors and carrier gases were delivered from the bottom. GaCl, NH3 and N2 were used as gallium source, nitrogen source and carrier gas, respectively. The C-face 6H-SiC substrate was employed in the subsequent HVPE growth. HCl gas reacted with liquid Ga at 500-800 °C to form GaCl, which was then transported to the template where it reacted with NH3 to form GaN.

Figure 1 shows the different growth steps. First, the substrate was heated to 600 °C for deposition of low temperature GaN (LT-GaN) buffer layer, which was grown with 1800 sccm of NH3 and 10 sccm of GaCl for 30 min. Thereafter, the temperature was increased to 1080 °C and kept constant for 10 min. The layer was annealed in this step in presence of NH3 to improve the crystallinity. Then, thick high temperature GaN (HT-GaN) was grown at 1050 °C with 1800 sccm of NH3 and 20 sccm of GaCl. Finally, the temperature was cooled down with 300 sccm of NH3.

Figure 1
figure 1

Schematic diagram of the growth process.

The morphologies of GaN were investigated by a field emission scanning electron microscope (FE-SEM, Hitachi S-4800). A cross-sectional EBSD measurement was carried out by an EBSD system (Oxford Instruments INCA Crystal EBSD system, Nordlys EBSD Detector and HKL CHANNEL5 software) in the FE-SEM. Structural characterization of LT-GaN buffer was carried out with a Burker AXS X-ray system using Cu-Kα radiation. The Raman spectroscopy (LabRAM HR system of Horiba Jobin Yvon) at room temperature using a 532 nm solid state laser as the excitation source was employed to identify the stress of the freestanding GaN. The accuracy during the Raman measurements was 0.5 cm−1 with a spot size of approximately 2.0 mm. High-resolution X-ray diffraction (HRXRD) characterizations were performed on a Bruker D8 Discover High Resolution X-Ray Diffractometer using symmetrical (002) and asymmetrical (102) reflections, which provided a resolution of about 13 arcsec and a slit width of 0.6 mm. The optical property was determined by room temperature photoluminescence (PL) measurements with a 325 nm He–Cd laser as the excitation source.

Results and discussion

The morphology of LT-GaN buffer before annealing with randomly oriented three dimensional GaN islands formed at onset of nucleation is shown in Fig. 2a. The image demonstrates a clear Volmer-Weber island growth mode because of the poor surface wetting between GaN and SiC16,17. The subsequent annealing step recrystallizes the layer. After annealing, the morphology changes and some flat regions appear as shown in Fig. 2c. Figure 2b shows 2θ − ω XRD diffraction pattern of LT-GaN buffer on SiC before annealing. From Fig. 2b, the LT-GaN buffer studied in this work has a single crystalline structure. The position of the peaks corresponds to wurtzite GaN and 6H-SiC, with the epitaxial relationship (0001) GaN//(0001) 6H-SiC.

Figure 2
figure 2

SEM images of LT-GaN buffer before annealing (a), after annealing (c,d) and 2θ − ω XRD diffraction pattern of LT-GaN buffer (b).

After cooling down process, a mirror-like GaN layer with a thickness of about 100 μm and area of about 4 cm2 was spontaneously separated from SiC substrate. The picture of freestanding GaN is shown in Fig. 3c. The separation occurred at the interface of the buffer and the SiC. The LT-GaN buffer and the annealing process are responsible for the separation of the GaN and the SiC. At high temperature, GaN is decomposed into liquid gallium and nitrogen gas. The threshold temperature for the thermal decomposition of GaN is known to be 830 °C18 and the decomposition rate rises with temperature19. LT-GaN buffer was grown on 6H-SiC directly. The crystallographic orientation relationship between GaN and 6H-SiC is shown as follows:

Figure 3
figure 3

SEM images of cross-section of LT-GaN buffer before annealing (a) and after annealing (b), backside of freestanding GaN (c).

Though the LT-GaN buffer studied in this work has a single crystalline structure, the crystal quality is poor which can be seen from Fig. 2b. This made the decomposition much easier. LT-GaN buffer before annealing was not separated from SiC. Figure 3a shows the cross-section of LT-GaN buffer before annealing. There are many small voids at the interface between LT-GaN buffer and SiC. The voids at the interface are confined, as a result, the supply of source materials for GaN, i.e., NH3 and GaCl, is virtually stopped. During annealing process, decomposition of GaN in the confined space begins as a result of the high temperature. The decomposition is significant on the N-face of the islands and buffer layer separated from SiC. Fig. 3b shows the cross-section of the LT-GaN buffer after annealing. The buffer is separated with the substrate though the buffer is very thin (about 500 nm) which indicates a very small interaction force between GaN and the substrate. This can also be seen from the bird’s-eye view of the LT-GaN buffer after annealing with many swell and drop off. (Figure 2d)

The freestanding GaN was etched in phosphoric acid at 240 °C for 30 min.The morphologies of the surface (Fig. 4a) and the back surface (Fig. 4b) after etching were shown in Fig. 4. GaN polarity can be identified after hot phosphoric acid etching since the etching rate and the resulting surface morphology is polarity dependent. Only N-polar GaN epilayers can be etched in phosphoric acid at 100 °C20. When the etching temperature is higher than 220 °C, the N-polar GaN films etched quickly, with either a drastic change in the surface morphology or complete film removal while only hexagonal etch pits associated with defects formed on Ga-polar films, leaving the defect-free GaN areas intact and the morphology unchanged21,22,23,24,25,26. According to Fig. 4, the GaN layer grown on C face 6H-SiC in this study is Ga-polar GaN.

Figure 4
figure 4

SEM images of the surface morphology and back surface morphology of freestanding GaN after hot phosphoric acid etching.

Raman spectroscopy has been widely used to identify the property of III-nitrides. In GaN, the E2 (high) phonon of Raman spectroscopy is used to characterize the in plane stress state of the GaN epilayer. The stress can be calculated by equation (1)27:

Where σ is the biaxial stress and ω is the E2 phonon peak shift. The E2 phonon of stress-free GaN is believed to be 566.2 cm−1 28. Figure 5a depicts the Raman spectra of the freestanding GaN grown on C face 6H-SiC. The position of E2 (high) phonon is at 566.2 cm−1, which indicates that the freestanding GaN grown on C face 6H-SiC is stress-free. Figure 5b shows the the back surface morphology of freestanding GaN. The decomposed area is more than 50%, which explains the stress state of the freestanding GaN.

Figure 5
figure 5

Raman spectroscopy of freestanding GaN (a) and SEM image of the back surface morphology (b).

The electron backscatter diffraction (EBSD) technique in a scanning electron microscope (SEM) is an effective technique for studying the crystal phase, orientation and lattice strain variation that are typical in semiconducting materials29,30. This technique allows us to probe the mechanism of the crystal quality improvement at the microstructural level with high spatial resolution and good strain sensitivity31,32,33. The Kikuchi patterns in EBSD is widely used to identify the crystallographic orientation of crystalline by conform the Miller index of the surface. Figure 6a showed the Kikuchi patterns in cross-sectional surface of freestanding GaN, the patterns were clear which means that the surface was flat and the crystal structure of GaN was perfect. The result indicates that the GaN cross-sectional surface is (11-20) plane.

Figure 6
figure 6

EBSD Kikuchi patterns (a), pole figures (b) and band slope (c) detected in cross-sectional GaN.

The EBSD mapping measurement was carried out at the cross-section of freestanding GaN. The polar figures of this section (Fig. 6b) were calculated by the HKL CHANNEL5 software depending on the mapping results, which confirm that the surface detected is (11-20) plane. The band slope (BS) was a measure of the quality of the original electronic backscattering patterns (EBSP) used in the indexing procedure. BS value is derived from the mean gradient of detected peaks in the Hough transform and is a measure of the sharpness of bands, with higher values representing better EBSP quality. The BS value is strain sensitive, especially in measurement of single crystals. Meanwhile, it reflects local dislocation concentrations. Figure 6c shows the BS from EBSD mapping data for cross-sectional surface of freestanding GaN. The BS value is small near the interface and increases when the distance to the interface becomes large. This predicts a decrease of strain and dislocation concentration upon growth. To be clear, the BS varies with surface polish or damage34, so the BS valve increases acutely near the surface corresponding to the rough area.

Figure 7 shows the ω-scans spectra from the symmetric (002) and asymmetric (102) planes of the freestanding GaN layers. HRXRD characterizations were performed to examine the misorientation between sub-grains, which mitigated by generation of dislocations. mosaic tilt reflects screw and mixed type TD density while twist indicates edge and mixed TD density. The full width at half maximum (FWHM) on the (002) reflection probes tilt which represents misorientation of sub-grains out-of-plane. The FWHM on the (102) reflection is sensitive to both tilt and twist. Thus, the FWHM of the (002) peak is usually used to evaluate the screw or mixed TDs density while the (102) peak is sensitive to all TDs. The FWHM of (002) peak is 261 arcsec (Fig. 7a) and the FWHM of (102) peak is 272 arcsec (Fig. 7b). The dislocation density can be calculated from equation (2)35:

Figure 7
figure 7

HRXRD rocking curves of the freestanding GaN films: (a) (002) ω-scans and (b) (102) ω-scans.

Where β is the FWHM and b is the Burgers vector. The calculated TD density in GaN layer is 1.17 E + 08 cm−2.

Figure 8 shows the room temperature PL spectra of the freestanding GaN grown on C face 6H-SiC. A strong band edge emission of GaN is found at 362 nm (3.425 eV), which confirms that the GaN layer is a hexagonal phase rather than cubic phase (excitonic emission around 3.2 eV).

Figure 8
figure 8

PL spectra of the freestanding GaN.

The TDs in the GaN film play the role of non-radiative recombination centers to deteriorate the luminescence efficiency36. The strong band edge emission demonstrates that the optical quality of the HVPE GaN layer is good and the TDs density is low. The FWHM of the band-edge emission is 123 meV. The very weak yellow luminescence band at 500–600 nm implies a low density of native defects, such as vacancies, interstitials and anti-sites in the sample37,38,39.

For a semiconductor, the band gap energy is changed by the stress applied to the layer. The band gap energy of GaN at room temperature under c-plane was reported as equation (3)40:

According equation (3), the strain of the freestanding GaN is approach to zero, which quite fits in with the result of the Raman spectroscopy.

Conclusion

The direct growth of GaN on the C-face 6H-SiC by HVPE has been demonstrated. The GaN was self-seperated from the 6H-SiC which can save both time and money to separate GaN layer and substrate. Moreover, the SiC substrate was excellent without damage after the whole process so that it can be repeatedly used in the GaN growth. The self-separation was attributed to the LT-GaN buffer and the annealing process. According to the hot phosphoric acid etching results, the obtained layer was Ga-polar GaN. According to the HRXRD results, the FWHM of (002) peak was 261 arcsec and the The FWHM of (102) peak was 272 arcsec. EBSD carried out at the cross-section of the freestanding GaN proved a high crystal quality and a decrease of strain and dislocation concentration upon growth. The Raman measurements and PL spectra showed that the freestanding GaN film grown on the C-face 6H-SiC was stress-free. The PL spectra also indicated good optical quality of the freestanding GaN layer.

Additional Information

How to cite this article: Tian, Y. et al. Direct growth of freestanding GaN on C-face SiC by HVPE. Sci. Rep. 5, 10748; doi: 10.1038/srep10748 (2015).