Abstract
We propose and analyze a superluminal ring laser gyroscope (RLG) using multilayer optical coatings with huge group delay (GD). This GD assisted superluminal RLG can measure the absolute rotation with a giant sensitivity-enhancement factor of ~103; while, the broadband FWHM of the enhancement factor can reach 20 MHz. This superluminal RLG is based on a traditional RLG with minimal re-engineering and beneficial for miniaturization according to theoretical calculation. The idea of using GD coatings as a fast-light medium will shed lights on the design and application of fast-light sensors.
Similar content being viewed by others
Introduction
Controlling the speed at which light propagates has been the focus of numerous studies during the past two decades1,2,3. In addition to its fundamental importance, the tunability of light speed also opens up new avenues for diverse applications ranging from optical data buffering to enhanced precision in interferometry. Recently, it has been shown that a fast-light medium can be used to realize an absolute rotation sensor whose sensitivity is enhanced with an enhancement factor as high as 1064. In this case, the fast-light enhanced gyroscope might be able to detect the gravitational frame-dragging effect terrestrially via measuring the Lense-Thirring rotation4,5. This enhancement is induced by a frequency dependent phase shift within a Ring Laser Gyroscope (RLG), which has been shown both theoretically5,6 and experimentally7,8 by means of increased “mode pushing” or “mode pulling” effects. Various systems have been investigated in order to achieve optimal performances for superluminal gyroscope applications, including alkali metal vapor cells7,8, coupled optical resonators9, photorefractive crystals10, optical fibers (dual-pumped Brillouin gain in a fiber or fiber-coupled whispering gallery resonators)11, spectral hole burning12 and rare atomic gases13.
Alkali metal vapor cells have been widely investigated as anomalous dispersion system. However, additional components are requested facing significant engineering challenges, which is disadvantageous for precise measurement. Moreover, since the operating wavelength is confined by the alkali metal atoms, the applications for alkali metal vapor cells are limited. For example, it is unable to realize a White-Light-Cavity that operates at 1064 nm in the application of a LIGO-like gravitational wave detector10. Coupled optical resonators9,14 can be conveniently employed to provide critical anomalous dispersion within a narrow-band spectral range with the assistance of some passive elements. However, the FWHM bandwidth for the sensitivity enhancement factor is narrow and the gyro is often too complex with a coupled cavity to accurately control its cavity length14. The photonic structures such as photorefractive crystals and optical fibers are more suitable to integrate with practical systems, but they all suffer from fundamental limitations to provide long delays of short pulses15,16,17. The nonlinear effect via spectral hole burning has been employed to induce dispersion which results in a scale factor enhancement of only 0.33~2 and an additional laser is needed12. In general, existing anomalous dispersion systems are still far from practical applications. Additional components such as a vapor cell, a pumping laser or a coupled cavity are needed, which makes the gyroscope complex and unstable, leading to additional errors such as backscattering. Therefore, to reach the full potential of fast-light enhanced RLG, novel materials or systems for fast-light are needed which are compact and request minimal re-engineering; the FWHM bandwidth of the enhancement factor should be large (broadband); and the novel materials or systems for fast light should not induce additional backscattering.
Multilayer optical coatings are most effective systems to modulate both the amplitude and phase of light18 by means of inducing group delay (GD) and group delay dispersion (GDD). For phase modulation, compared with other dispersive medium, multilayer coatings are compact, low-loss and convenient to be integrated with other systems. Thus, they have been widely used in the field of dispersion enhancement and dispersion compensation, such as Chirped mirrors and Gires-Tournois mirrors19,20,21,22,23. In this paper, we demonstrate a new design of a broadband superluminal ring laser gyro by employing multilayer optical coatings with huge GD on one of the mirrors while keeping its high-reflectivity property. Meanwhile, we have computed the enhancement factor (Senh) of the superluminal gyro and examined a number of parameters including the FWHM bandwidth for Senh, the scale factor linearity and the cavity length dependence for miniaturization issues. This GD involved superluminal RLG can greatly enhance the sensitivity of rotation measurement by a factor of 103; while, the broadband FWHM can reach 20 MHz. On contrast to all its merits, this superluminal RLG is compact and beneficial for miniaturization.
Results
The transformation function for multilayer optical coatings can be written as:
where |H(ω)| is the light amplitude, ϕ(ω) is the phase shift when light propagates through the multilayer coatings. ϕ(ω) can be expanded using Taylor series around ω022:
where is defined as the group delay, is the group delay dispersion, f and ω are the frequency and angular frequency. Let us consider a square RLG with four high-reflectivity mirrors (M1, M2, M3 and M4), in which M4 is the one with a huge GD induced by multilayer coatings and M3 is the output mirror, as illustrated in Figure 1. The lead zirconium titanate (PZT) plate on M1 is used to control the laser cavity length. Compared to traditional RLGs, the only change is the multilayer coatings on M4, which requires minimal re-engineering for practical updating from old designs. Due to the huge GD induced by M4, Sagnac effects of the system need to be re-calculated as follows:
For an active RLG shown in Figure 1, the clockwise (CW) and counter-clockwise (CCW) ring laser modes have different frequencies (Δf = f− − f+) because of the difference in effective round-trip optical path lengths caused by the rotation of the cavity. Here, we denote f±, λ± and 〈L±〉 as the frequencies, wavelengths and effective optical cavity lengths seen by the CW and CCW propagating beams, respectively. 〈L±〉 can be expressed as follows:
where 〈L〉 is the round-trip optical path length of the RLG without rotation, r0 is the radius of the beam path for ring cavities, Ω is the angular velocity rotating about the normal axis through the center of the interferometer, c is the speed of light. When considering the huge GD effects of M4, the frequency difference Δf will induce additional phase difference. Thus, the resonance conditions for the CW and CCW propagating beams can be rewritten as:
where α is a factor valued between 0 and 1, q1 and q2 are integers, λ+ = c/f+, λ− = c/f−. Combining equation (3) and (4), we can obtain equation (5):
where m = q1 − q2. Assuming m = 0 and r0Ω ≪ c, we can express equation (5) using Taylor series and the first order terms can be expressed by:
Under such approximation, we have f+ + f− = 2 f0, where f0 is the frequency of the CW and CCW beams in RLG without rotation. Then we can obtain the following result:
where is the area enclosed by the beam path, λ is the wavelength of the CW and CCW beams at zero rotation. For , , equation (7) becomes the formula for a usual RLG. For (the case shown in our design), a sensitivity enhancement factor Senh for the superluminal RLG can be calculated as
Therefore, when , |Senh| > 1, the scale factor of RLG is enlarged. For , the enhancement factor reaches its maximum. Therefore, it is critical to design multilayer optical coatings with GD around , while maintaining the high-reflectivity property of the coatings for RLG. For multilayer optical coatings, there are many designs meeting above requirements. Considering practical applications, we choose the quarter-wave multilayer structure as follows:
where H and L indicate quarter-wave optical layers with high and low refractive-index at 45° angle of incidence at a center wavelength of 632.8 nm. Figure 2(a) shows the theoretical refractive-index profile of a high-reflectivity Ta2O5-SiO2 multilayer coatings (G/(HL)25H2L(HL)14/A). In the case of ion beam sputtering (IBS) for the high-reflectivity mirrors, Ta2O5 is usually selected as high refractive-index material (n = 2.125) and SiO2 as low refractive-index material (n = 1.46). In fact, the multilayer structure of G/(HL)25H2L(HL)14/A is composed of a 23-layer high-reflectivity mirror ((HL)11H) and a 57-layer narrow bandpass filter ((LH)142L(HL)14). Figure 2(b) and (c) show the computed reflectivity and GD curves as functions of wavelength for the RLG design illustrated in Figure 2(a). The calculated results suggest that this is a broadband high-reflectivity multilayer-coating system with huge GD (964228.61851 fs at maximum) at the central wavelength of 632.8 nm. At the maximum GD, for the cavity optical length of 289.55 mm, the enhancement factor Senh can reach as high as 1029 according to equation (8). Both the high-reflectivity mirrors in RLG and the bandpass filters in dense wavelength division multiplexing (DWDM) are widely used and the technology is mature, therefore this kind of superluminal RLG should be achievable.
Considering practical applications of the superluminal RLG, the FWHM bandwidths of GD and Senh are very important, which need to be larger than the linewidth of the laser cavity, otherwise extremely accurate control of cavity length is required14. Figure 3(a) shows the computed GD (in green) and Senh (in black) versus detuning of laser frequency Δf using parameters provided above. The peak value of Senh ≈ 1029 occurs at Δf = 0 (ω = ω0 = 2πc/λ0, where λ0 = 632.8 nm) and the FWHM bandwidth of enhancement factor Senh is ~20 MHz. For a regular round trip loss σ ~ 300 ppm of the RLG, the linewidth of the ring laser cavity is . Thus, the FWHM bandwidth of Senh of our design is two orders of magnitude higher than the linewidth of ring laser cavity. We have also calculated the beat frequency fb of fast-light enhanced RLG with respect to angular rotation rate Ωr. The relationship between the beat frequency of a standard RLG and the rotation rate is fb = 4AΩr/(Lrλ) according to equation (7), neglecting the effects of frequency lock-in. For a fast-light enhanced RLG, this expression needs to be modified to include the increased sensitivity term Senh: fb = 4ASenhΩr/(Lrλ). Figure 3(b) shows the beat frequency of both fast-light enhanced (black curve) and standard HeNe (red curve) RLGs with respect to the angular rotation rate. The inset gives an expanded view of the fb vs Ωr plot for fast-light enhanced RLG with a rotation rate ranged from −30 to 30 rad/s. It shows a perfect linear relation within this rotation speed range with its linear fitting shown in dashed blue line. This linear dynamic range of fast-light enhanced gyroscope is more than enough for usual navigation applications.
More importantly, equation (8) indicates that, in order to reach the same Senh, for shorter optical cavity length, the GD value required is smaller, which reduces the number of layers in the mirror coatings and greatly lowers the design and fabrication difficulty in applications. Figure 4(a) shows the calculated GD curves with respect to the wavelength for ring lasers at various optical cavity lengths of 289.55 mm (black line), 30.47 mm (red line), 3.206 mm (blue line) and 0.3371 mm (green line), respectively. The corresponding multilayer coatings are 80 (G/(HL)25H2L(HL)14/A), 70 (G/(HL)232H(LH)11L/A), 60 (G/(HL)20H2L(HL)9/A) and 50 layers (G/(HL)182H(LH)6L/A), respectively. This suggests that, when the optical cavity length <L> decreases, the required number of layers in the mirror coatings and their GD value decease. Meanwhile, the bandwidth of GD(λ) increases (Figure 4(a)), so that this type of fast-light enhanced RLG is beneficial for miniaturization. Figure 4(b) shows the FWHM bandwidth of GD(λ) (in black), the FWHM bandwidth of Senh(Δf) (in red) and the layers of multilayer coatings (in blue) with respect to the laser optical cavity length <L>, respectively, where the maximum Senh is kept as constant at ~1000. It is obvious to see that, when the <L> decreases from 289.55 mm to 0.3371 mm, the number of layers required for the coatings deceases from 80 to 50; while, the GD(λ) FWHM bandwidth increases from ~0.01 Å to 7.64 Å. Therefore, the multilayer coatings with GD used for superluminal gyroscope can be realized more easily for RLGs with shorter optical cavity lengths. This multilayer optical coatings with a GD(λ) FWHM bandwidth of 7.64 Å can be easily realized by modern IBS method with optical monitoring of the central wavelength.
Discussion
Compared with other fast-light media or systems for superluminal gyroscopes such as alkali metal vapor cells7,8, coupled optical resonators9, photorefractive crystals10, optical fibers11, spectral hole burning12 and rare atomic gasses13, the GD induced superluminal gyroscope has significant advantages as follows. Firstly, the multilayer-coating system with GD is based on the traditional RLG with updating of only one mirror, which requires minimal re-engineering and will not introduce additional backscattering. Through optimizing the design of multilayer optical-coating systems, the operating wavelength of this GD induced RLG can be tunable to meet different applications. Secondly, the FWHM bandwidth of the enhancement factor Senh is much larger than the linewidth of the ring laser cavity, which increases the tolerance of the system for deviations in cavity length. Thirdly, this type of fast-light enhanced RLG is beneficial for miniaturization. With the development of micro-cavity technology such as vertical cavity emission lasers (VCSEL)24,25,26 and integrated micro RLGs27,28,29,30, micro fast-light enhanced RLG is promising to be realized in future with the idea of using multilayer coatings with huge GD.
In summary, we have proposed and analyzed a superluminal ring laser gyro using multilayer optical coatings with huge GD. This type of superluminal RLG has a strong sensitivity enhancement and a broadband enhancement factor that requires minimal re-engineering and advantageous for miniaturization. The idea of using GD coatings as fast-light media will shed lights on the design and application of fast-light sensors.
Methods
Considering the GD of multilayer coatings, Sagnac effects of the superluminal RLG are calculated according to the principle of laser physics directly as shown in the text, which is simple, clear and accurate. The design and computation of multilayer coatings are done by OptiLayer Thin Film Software, two targets (reflectivity and GD) are set for evaluation.
References
Hau, L. V., Harris, S. E., Dutton, Z. & Behroozi, C. H. Light speed reduction to 17 metres per second in an ultracold atomic gas. Nature (London) 397, 594 (1999).
Wang, L. J., Kuzmich, A. & Dogariu, A. Gain-assisted superluminal light propagation. Nature (London) 406, 277 (2000).
Bigelow, M. S., Lepeshkin, N. N. & Boyd, R. W. Superluminal and slow light propagation in a room-temperature solid. Science 301, 200 (2003).
Shahriar, M. S. et al. Ultrahigh enhancement in absolute and relative rotation sensing using fast and slow light. Phys. Rev. A 75, 053807 (2007).
Shahriar, M. S. & Salit, M. Application of fast-light in gravitational wave detection with interferometers and resonators. J. Mod. Opt. 55, 3133 (2008).
Smith, D., Chang, H., Arissian, L. & Diels, J. C. Dispersion-enhanced laser gyroscope. Phys. Rev. A 78, 053824 (2008).
Smith, D., Myneni, K., Odutola, J. A. & Diels, J. C. Enhanced sensitivity of a passive optical cavity by an intracavity dispersive medium. Phys. Rev. A 80, 011809(R) (2009).
Pati, G. S., Salit, M., Salit, K. & Shahriar, M. S. Superluminal ring laser for hypersensitive sensing. Opt. Comm. 281, 4931 (2008).
Terrel, M. A., Digonnet, M. J. F. & Fan, S. Coupled resonator gyroscopes: what works and what does not. Proc. SPIE 7612, 76120B (2010).
Yum, H. N. et al. Fast-light in a photorefractive crystal for gravitational wave detection. Opt. Express 16, 20448 (2008).
Yum, H. N., Liu, X., Jang, Y. J., Kim, M. E. & Shahriar, M. S. Pulse Delay Via Tunable White Light Cavities Using Fiber-Optic Resonators. J. Lightwave Technol. 29, 2698 (2011).
Salit, M., Salit, K. & Bauhahn, P. E. Increasing the scale factor of a ring laser gyro via spectral hole burning. Proc. SPIE 8273, 82730H (2012).
Salit, M., Salit, K. & Bauhahn, P. Prospects for enhancement of ring laser gyroscopes using gaseous media. Opt. Express 19, 25311 (2011).
Schaar, J. E., Yum, H. N. & Shahriar, S. M. Theoretical Description and Design of a Fast-Light Enhanced Helium-Neon Ring-Laser Gyroscope. Proc. SPIE 7949, 794914 (2011).
Khurgin, J. B. Dispersion & loss limitations on the performance of optical delay lines based on coupled resonant structures. Opt. Lett. 32, 133 (2007).
Khurgin, J. B. Performance limits of delay lines based on optical amplifiers. Opt. Lett. 31, 948 (2006).
Khurgin, J. B. Optical buffers based on slow light in electromagnetically induced transparent media and coupled resonator structures: comparative analysis. J. Opt. Soc. Am. B 22, 1062 (2005).
Bruce, C. F. & Ciddor, P. E. Phase Dispersion in Multilayer Films. J. Opt. Soc. Am. 50, 295 (1960).
Bennett, J. M. Precise method for measuring the phase change on reflection. J. Opt. Soc. Am. 54, 612 (1964).
Szipocs, R. & Ferencz, K. Chirped multilayer coatings for broadband dispersion control in femtosecond lasers. Opt. Lett. 19, 201 (1994).
Tikhonravov, A. V., Baumeister, P. W. & Popov, K. V. Phase properties of multilayers. Appl. Opt. 36, 4382 (1997).
Chen, L. J. et al. Broadband dispersion-free optical cavities based on zero group delay dispersion mirror sets. Opt. Express 18, 23204(2010).
Pervak, V., Fedorov, V., Pervak, Y. A. & Trubetskov, M. Empirical study of the group delay dispersion achievable with multilayer mirrors. Opt. Express 21, 18311 (2013).
Passaro, V. M. et al. Recent Advances in Integrated Photonic Sensors. Sensors 12, 15558 (2012).
Weng, W., Chow, K. D., Choquette, M. H., Kevin, L. L. & Hadley, G. R. Design, Fabrication and Performance of Infrared and Visible Vertical-Cavity Surface-Emitting Lasers. IEEE J. Quantum Elect. 33, 1810 (1997).
Kent, D. C. & Hong, Q. H. Vertical-Cavity Surface Emitting Lasers: Moving from Research to Manufacturing. Proceedings of the IEEE 85, 1730 (1997).
Zhang, T. et al. Integrated optical gyroscope using active Long-range surface plasmon-polariton waveguide resonator. Sci. Rep. 4, 3855 (2014).
Mignot, A. et al. Single-frequency external-cavity semiconductor ring-laser gyroscope. Opt. Lett. 34, 97 (2009).
Zhang, R., Ren, Z. & Yu, S. Loss-Reduction in Flexibly Vertical Coupled Ring Lasers Through Asymmetric Double Shallow Ridge and ICP/ICP Cascade Etching. IEEE Photonics Technol. Lett. 20, 1821 (2008).
Ciminelli, C., DellOlio, F., Campanella, C. E. & Armenise, M. N. Photonic technologies for angular velocity sensing. Adv. Opt. Photon. 2, 370 (2010).
Acknowledgements
This work was supported by the National Science Foundation of China (Grant No. 11304384), Research Project of National University of Defense Technology (Grant No. JC13-07-02) and Open Research Fund Program of the State Key Laboratory of Low-Dimensional Quantum Physics.
Author information
Authors and Affiliations
Contributions
T.L.Q. designed the superluminal gyroscope and performed the calculation. K.Y.Y. directed the research. X.H. carried out the calculation of Sagnac effects of the superluminal RLG when considering the GD of multilayer coatings. S.Y.W. assisted in the design and computation of multilayer coatings by Optilayer Software. T.L.Q. and K.Y.Y. prepared the manuscript and refined the paper. Y.H. and H.L. provided advices and helpful theoretical discussion. All authors discussed the results and contributed to the refinement of the paper.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article's Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder in order to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Qu, T., Yang, K., Han, X. et al. Design of a superluminal ring laser gyroscope using multilayer optical coatings with huge group delay. Sci Rep 4, 7098 (2014). https://doi.org/10.1038/srep07098
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep07098
This article is cited by
-
On-chip modulation for rotating sensing of gyroscope based on ring resonator coupled with Mach-Zehnder interferometer
Scientific Reports (2016)
-
On-chip tunable dispersion in a ring laser gyroscope for enhanced rotation sensing
Applied Physics A (2016)
-
Practical Considerations on the Multi-layer Mirrors for Superluminal Ring Laser Gyroscopes
Scientific Reports (2015)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.