A kinetic descriptor for the electrolyte effect on the oxygen reduction kinetics on Pt(111)

Proton-exchange membrane fuel cells demand efficient electrode–electrolyte interfaces to catalyse the oxygen reduction reaction (ORR), the kinetics of which depends on the energetics of surface adsorption and on electrolyte environment. Here we show an unanticipated effect of non-specifically adsorbed anions on the ORR kinetics on a Pt(111) electrode; these trends do not follow the usual ORR descriptor, that is *OH binding energy. We propose a voltammetry-accessible descriptor, namely reversibility of the *O ↔ *OH transition. This descriptor tracks the dependence of ORR rates on electrolyte, including the concentration/identity of anions in acidic media, cations in alkaline media and the effect of ionomers. We propose a model that relates the ORR rate on Pt(111) to the rate of the *O to *OH transition, in addition to the thermodynamic *OH binding energy descriptor. Our model also rationalizes different trends for the ORR rate on stepped Pt surfaces in acidic versus alkaline media. The deployment of fuel cells demands more efficient electrode–electrolyte interfaces to catalyse the oxygen reduction reaction (ORR). A kinetic ORR descriptor is put forward, which is related to the rate of the *O ↔ *OH transition and includes electrolyte effects via the role of non-specifically adsorbed anions.

T he operating energy efficiency of proton-exchange membrane fuel cells (PEMFCs), an appealing power source for transportation, remains well below the thermodynamic value of 83%, primarily because of the high overpotential of the cathodic oxygen reduction reaction (ORR) [1][2][3][4][5] . Because of the high cost and low abundance of platinum-currently an indispensable catalytic element for ORR in PEMFCs-substantial efforts have been devoted to deliberately structuring Pt-based nanocatalysts in terms of composition 6,7 , architecture 8-10 and geometry 11,12 , having realized substantial enhancements in both fundamentally intrinsic activity and industry-relevant mass activity in acidic environments 13 .
Part of this progress was guided by a descriptor-based approach, in which the activity of the catalyst is related to the binding energy of the key adsorbed intermediates. A widely adopted ORR descriptor is the oxygen or hydroxyl adsorption energy. Using such a descriptor as the key catalyst property, catalyst-dependent ORR activities are arranged in a so-called volcano plot, with the best catalyst possessing the most optimal oxygen binding energy located at the top of the volcano [14][15][16] . However, the ORR has multiple oxygen-containing intermediates, and they cannot all be optimized independently because their binding energies exhibit a scaling relation: if one binding energy changes, the others change as well, often in a very predictable way. Such scaling relations eliminate the possibility of independent tuning of each intermediate, and yield a minimum thermodynamic overpotential that cannot be overcome by solely engineering the solid surface for optimum adsorption 17,18 . Thus, a formidable challenge is to break the scaling relation, with limited experimental success achieved to date 19 .
One important (often tacit) assumption in the volcano approach is that a catalytic reaction has a single descriptor. However, it is well known that (electro)catalytic reactions may have multiple descriptors; hydrogen evolution/oxidation in alkaline media is a good example, the multiple descriptors of which are currently much discussed in the literature 20,21 . For the ORR, it appears that oxygen binding energy is a good descriptor when it comes to the properties of the catalyst. However, as we will show here, there is also a significant effect of the electrolyte on ORR activity, which does not follow the predictions of this descriptor. ORR activities are routinely evaluated in 0.1 M HClO 4 environments, because of the quantitative agreement between activities of a benchmark nanoparticulate Pt catalyst measured in a half-cell and in a membrane electrode assembly 22 . Hydrated non-specifically adsorbed anions, located at the outer Helmholtz plane (OHP), are generally considered to be innocent to the intrinsic ORR activity, although hydrated cations have been reported to regulate ORR kinetics in alkaline media 23 .
We show here that non-specifically adsorbed (NSA) anions are in fact not innocent to the ORR activity, and that the ORR activity trend with anion concentration on Pt(111) cannot be rationalized on the basis of the thermodynamic oxygen binding energy descriptor. We therefore introduce a kinetic descriptor, related to the kinetics of the *O to *OH transition on Pt(111), which correlates well with the electrolyte-induced activity trends in both acidic and alkaline media. The kinetic descriptor also explains the effect of the perfluorosulfonic acid (PFSA) ionomer on ORR activity. We will then discuss how a combination of the traditional thermodynamic descriptor with our kinetic descriptor can rationalize the different ORR activity trends for stepped Pt surfaces in acidic and alkaline media. We believe that our enhanced model for what determines the ORR activity, including both thermodynamic and kinetic factors, pays more credit to the intrinsic complexity of the reaction compared to the traditional volcano model, and provides an avenue towards a more complete understanding of the various factors that determine the ORR rate on Pt surfaces.

Results
CVs and ORR activities of Pt(111) in 0.1 and 0.02 M HClO 4 . We first investigated how NSA anions affect the chemisorption of oxygen-containing species on Pt(111), which is relevant to the electrocatalytic performance for ORR. Figure 1a compares the blank cyclic voltammograms (CVs) of Pt(111) in HClO 4 for two concentrations, that is, the customary 0.1 M and a more diluted 0.02 M solution, both showing the typical voltammetric characteristics of a Pt(111) surface. Negligible differences in the hydrogen underpotential desorption (H upd , between 0.07 and 0.35 V) or double-layer charging (DL, between 0.35 and 0.55 V) regions were observed between the two electrolytes, indicating the absence of surface reconstruction or specific adsorption. On the other hand, a small but significant difference in the reversible OH adsorption A kinetic descriptor for the electrolyte effect on the oxygen reduction kinetics on Pt(111) Mingchuan Luo and Marc T. M. Koper ✉ Proton-exchange membrane fuel cells demand efficient electrode-electrolyte interfaces to catalyse the oxygen reduction reaction (ORR), the kinetics of which depends on the energetics of surface adsorption and on electrolyte environment. Here we show an unanticipated effect of non-specifically adsorbed anions on the ORR kinetics on a Pt(111) electrode; these trends do not follow the usual ORR descriptor, that is *OH binding energy. We propose a voltammetry-accessible descriptor, namely reversibility of the *O ↔ *OH transition. This descriptor tracks the dependence of ORR rates on electrolyte, including the concentration/identity of anions in acidic media, cations in alkaline media and the effect of ionomers. We propose a model that relates the ORR rate on Pt(111) to the rate of the *O to *OH transition, in addition to the thermodynamic *OH binding energy descriptor. Our model also rationalizes different trends for the ORR rate on stepped Pt surfaces in acidic versus alkaline media.
(OH ad , between 0.55 and 0.85 V) region is observed, with an overall higher charge of OH ad in 0.02 M compared with 0.1 M HClO 4 (Fig. 1b). The similar OH ad profiles between 0.1 M HClO 4 and a control electrolyte (0.02 M HClO 4 + 0.08 M KClO 4 ) suggest that OH ad formation is more sensitive to the anion concentration than to the electrolyte pH (see the corresponding curve in Fig.1b). This indicates that the saturation coverage of OH ad is electrolyte dependent (as it is known that perchlorate interacts with OH ad (refs. 24,25 ), it presumably interferes with the lateral interactions between adsorbed OH).
The OH ad adsorption energy of a Pt surface has been widely used to predict the corresponding ORR activity, on the basis of two proposed mechanisms. The first mechanism suggests that OH ad serves as a non-reactive spectator and blocks surface active sites for the adsorption of molecular O 2 (refs. 6,26,27 ). As a result, a lower OH ad coverage (Θ *OH ) at the potential of interest (ORR activity is customarily evaluated at 0.9 V versus Reversible Hydrogen Electrode (RHE)) results in a higher ORR activity because of a higher pre-exponential factor (1 − Θ *OH ) in the rate expression. Here, it is important to note the distinction between NSA (for example, ClO 4 − and methanesulfonate) and specifically adsorbed anions (for example, HSO 4 − , Cl − and Br − ); the latter (located in the inner Helmholtz plane) directly impact the ORR rate by contributing to the (1 − Θ ad ) term (where Θ ad includes both *OH and specifically adsorbed anions) of the rate expression given by Marković et al. 26,27 . The second mechanism is based on the notion that OH ad , as an intermediate, binds too strongly on Pt(111), and needs to be weakened by ~0.1 eV to reach the top of the volcano 28,29 . It has been proposed that an experimental measure of the OH ad adsorption strength can be indicated by the electrode potential required for a Θ *OH of 1/6 monolayer, that is, 40 μC cm −2 for Pt(111) (dashed line in Fig. 1b) 30 . A more negative (positive) potential then means stronger (weaker) OH ad adsorption strength. Both mechanisms predict a lower ORR activity for Pt(111) in 0.02 M HClO 4 compared with 0.1 M HClO 4 because of a higher Θ *OH and a more negative potential for 1/6 of Θ *OH .
Strikingly, we find the opposite trend experimentally. Figure Fig. 1c). We find that the Tafel slope increases slightly with the HClO 4 concentration, but is close to 60 mV dec −1 in all cases ( Fig. 1d and Supplementary Table 1), which agrees well with the literature and suggests that the ORR mechanism is independent of electrolyte 32 . We note here that, for ORR on Pt surfaces, derivation of the rate-determining step (RDS) from the measured Tafel slope is not straightforward and remains disputed 33   Supplementary Fig. 2 for corresponding Arrhenius plots), underscoring the negative impact of ClO 4 − on the ORR kinetics. The above observations suggest that ORR rate on a Pt surface cannot be solely described by the thermodynamic binding energy descriptor, and imply the existence of another factor that accounts for the above-observed electrolyte effect. To pursue the origin of this effect, we revisit the ORR mechanism on Pt surfaces, which can be simplified as follows 34,35 : where * represents an adsorption site on the surface. This mechanism involves three adsorbed reaction intermediates, that is, *OOH, *O and *OH. Probing these intermediates under reaction dynamics remains a huge challenge. However, existing experimental evidence from both ex situ and in situ ambient-pressure X-ray photoelectron spectroscopy (XPS) suggests that, within the mixed kinetic-diffusion potential region, the dominant surface species gradually change from *O to *OH with increasing ORR overpotential 36,37 .
This highlights the role of *O as a key surface adsorbate for ORR proceeding at the potential of interest, that is 0.9 V, and thus motivates us to investigate the voltammetry of *O and to further probe its functional link with the ORR kinetics on Pt surfaces.

A descriptor for electrolyte effect on ORR.
To study the kinetics of the *O to *OH transition, we recorded CVs of Pt(111) in an extended potential window (between 0.07 and 1.15 V) in HClO 4 of four concentrations (Fig. 2a). The upper potential limit of 1.15 V was chosen to avoid irreversible surface reconstruction of Pt(111) 38 . Following the traditional interpretation, we assigned the anodic peak located between 0.95 and 1.1 V as the oxidation of *OH to *O 38 . A typical characteristic of high-quality Pt(111) surface is the plateau between 0.85 and 1 V, which was previously interpreted as a high kinetic barrier to oxidize Pt(111) with a 1/3 monolayer of Θ *OH , based on density functional theory (DFT) calculations and electrochemical impedance spectroscopy (EIS) studies 39 . The most pronounced trend from Fig. 2a is that the *O peak shifts positively with the HClO 4 concentration, which suggests that *OH → *O conversion is easier in an electrolyte with a lower ClO 4 − concentration. The reverse reduction of *O to*OH (step 3 of ORR) is then expected to show the same electrolyte dependence. However, the kinetically slow *O → *OH reduction peak overlaps with the fast *OH desorption peak, giving rise to a broad reduction peak between 0.55 and 1 V in the CV (Fig. 2a), comprising both processes. Such a convolution poses experimental difficulties to probe the electrolyte-dependent kinetics of *O to *OH transition on Pt(111). To deconvolute these two processes, we performed experiments at different scan rates and different temperatures. Leveraging the kinetic difference of *O to *OH transition and *OH desorption on Pt(111), we can manipulate their respective positions by recording CVs at different scan rates from 200 to 10 mV s −1 (Fig. 2b). The two reductive processes were gradually deconvoluted with decreasing scan rate, and became fully separated at 10 mV s −1 . The forward and backward peaks corresponding to the *O ↔ *OH redox have a smaller peak-to-peak potential difference at a slower scan rate, proving that there is a kinetic barrier associated with this reaction. Another way to deconvolute the peak is to accelerate the sluggish *O ↔ *OH rate by increasing temperature. Recording CVs of Pt(111) as a function of temperature, we observe a gradual separation of the reduction peaks with increasing temperature (Supplementary Fig. 3). Notably, both scan-rate-and temperature-controlled experiments suggest an electrolyte dependence of the *O ↔ *OH kinetics, namely that it proceeds faster in more diluted HClO 4 .
In another typical NSA electrolyte, that is methanesulfonic acid (MSA), we observed the same concentration dependence of the ORR activity on Pt(111), suggesting generality of the suppression effect of NSA anions towards ORR (Fig. 2c). Figure 2c plots the specific activity of ORR on Pt(111), denoted by the kinetic current density at 0.9 V (j k , see Methods for calculation details), which decreases with HClO 4 and MSA concentration (Fig. 2c), or more specifically, with lower perchlorate and methanesulfonate concentration. The measured j k of Pt(111) in 0.1 M HClO 4 is 1.93 mA cm −2 , in good agreement with the literature 6 . The effect of the methanesulfonate concentration on the kinetics of the *O ↔ *OH process is also identical to the effect of the perchlorate concentration ( Supplementary Fig. 4).
The observation that the rate of both *O ↔ *OH and ORR depend on the concentration of NSA anions in the same way, suggests that they are related; or more specifically, the rate of the *O ↔ *OH process may act as a descriptor of the ORR rate. To provide quantitative support for this relation, we plot the kinetic current at 0.9 V of ORR versus peak-to-peak separation (ΔE peak ) of the *O ↔ *OH process in Fig. 3a,b. Increasing from 0.02 to 0.1 M HClO 4 , the anodic and cathodic peak shifts positively and negatively, respectively, by ~25 mV, very close to the E 1/2 change of ORR (Fig. 1c). The smaller the ΔE peak , the more reversible the *O ↔ *OH process, and the faster the ORR rate. We will discuss possible interpretations of this relation in the Discussion section.

Effects of alkaline cations and ionomers.
Having introduced a kinetic descriptor for the electrolyte effect on Pt(111) in acid solution, we now show its applicability in alkaline media, in which hydrated cations are the main electrolyte players. We recorded CVs of Pt(111) in 0.1 M and 0.02 M NaOH using a slow scan rate of 10 mV s −1 , to deconvolute the two cathodic processes ( Supplementary Fig. 5a). At a lower NaOH concentration of 0.02 M, the peaks related to *O ↔ *OH redox are more reversible. According to the proposed descriptor, Pt(111) would show a higher ORR activity in 0.02 M than in 0.1 M NaOH, which was verified experimentally by a positive shift of E 1/2 by 12 mV (Supplementary Fig. 5b). The kinetic descriptor also tracks the ORR dependence of monovalent cation identity in alkaline electrolytes. On Pt(111), the reversibility of *O ↔ *OH redox and ORR activity follow the same trend of LiOH < NaOH < KOH < CsOH (refs. 23,40 ). Our kinetic descriptor is also valid for the effect of bivalent cations, such as Ba 2+ , on the ORR kinetics of Pt(111) in alkaline solutions 41 .
In real fuel cells, Pt catalysts are generally surrounded with hydrated PFSA-based ionomer instead of anions or cations 42,43 . We investigated the effect of ionomers on CVs and ORR activities of Pt(111) by depositing a thin layer of the widely adopted Nafion ionomer (see Methods for details). The orientation of Pt(111) was well preserved after the deposition, as evidenced from the negligible change in H upd profile (Fig. 4a). We observed a higher peak potential for the *OH to *O transition, and a lower ORR activity on Nafion-covered Pt(111) relative to the unmodified Pt(111), validating our kinetic descriptor (Fig. 4b). Further experimental support can be found in the work from Kodama et al., who showed that the ORR activity decreases as bare Pt(111) > perfluorosulfonimide-coated Pt(111) > Nafion-coated Pt(111), while the peak potential for the *OH to *O transition follows the opposite trend 44 , in agreement with our kinetic descriptor. Our finding offers a plausible explanation for the counterintuitive observation that the addition of ionomers negligibly impacts the electrochemical surface area of nanoparticulate Pt catalyst, yet deteriorates its intrinsic activity 45 . This provides an important insight into the challenge of the performance transfer of advanced nanocatalysts from half-cell measurements to membrane electrode assembly (MEA) systems 46,47 .
Electrolyte effect on stepped surfaces and an enhanced model. Finally, we want to show how our kinetic descriptor can be used to offer an explanation for an unsolved puzzle in understanding ORR activity trends on stepped Pt surfaces in acidic and alkaline media. To show the relation between our kinetic descriptor and ORR activity on stepped Pt, we employed a series of Pt (111) Fig. 5b, which suggests that a single-crystal Pt surface with a higher step density is less sensitive to the electrolyte effect. We therefore deduce that the electrolyte effect mainly applies to the (111) terraces of Pt surfaces, but also that terraces still make a significant contribution to the overall ORR activity of stepped Pt surfaces.
Stepped Pt surfaces are known to show higher ORR activities than Pt(111) in 0.1 M HClO 4 (refs. 31,49 ). Previous studies have explained this phenomenon based on the oxygen binding energy descriptor. Two types of active sites, categorized by the so-called generalized coordination number, were proposed on stepped surfaces as illustrated in Fig. 5c. Site A (terrace atoms adjacent to steps) has a higher generalized coordination number than site B (basically equal to the terrace atom of Pt(111) electrode). This endows stepped Pt surfaces with lower oxygen binding energy and thus higher ORR activity than Pt(111) following the traditional thermodynamic descriptor, as supported by voltammetry and DFT calculation results 12,50 . However, previous studies rarely discussed the fact that sites of type B (less energetically favourable sites) also contribute to the ORR rate of stepped surfaces, which show a strong electrolyte effect as demonstrated above. Therefore, we propose an enhanced model for ORR electrocatalysis on Pt surfaces: the ORR rate is jointly governed by the electrode and electrolyte effect, which can be modelled by the traditional thermodynamic oxygen binding energy descriptor and our proposed kinetic descriptor of the *O to *OH transition rate, respectively (Fig. 5c). While the thermodynamic descriptor ascribed higher activities of stepped Pt surfaces to the presence of site A; the kinetic descriptor predicts higher ORR activities on site B of all Pt surfaces with a lower concentration of NSA anions, with Pt(111) being the most sensitive ( Fig. 5d and Supplementary Table 2).
With this model, we can understand the longstanding puzzle of the different structure sensitivity of ORR on Pt surfaces in acid versus alkaline media-compared with stepped surfaces, the ORR rate of Pt(111) is lower in acid, but higher in alkaline media 51 . In acid, site A serves as the dominant reactive site according to the thermodynamic descriptor, which explains the higher ORR rate of stepped surfaces. In alkaline media, previous studies found that alkali metal cations are preferentially located at the step sites 21,52 . This results in the blockage of site A and as a result site B provides the main contribution to the ORR activity on stepped Pt surfaces (Fig. 5c). In this scenario, the ORR rate is solely governed by the kinetic descriptor according to the above proposed model. Using E *O (Fig. 5a) as a kinetic descriptor, Pt(111) is then predicted to have a higher ORR activity than stepped Pt surfaces because of a faster *O to *OH transition on Pt(111) compared with stepped surfaces, in agreement with the experimental trend.

Discussion
The ORR is a complex multi-proton multi-electron transfer reaction. In the traditional approach for modelling the ORR activities of various electrocatalysts, this complexity is mapped onto a single thermodynamic descriptor, namely the binding energy of *OH or *O on the catalyst. This descriptor has a proven ability to predict and/or reproduce many experimental trends 14 , but there remain experimental observations for which this descriptor has no explanative or predictive power. In this paper, we have shown that one such experimental observation is the effect of the electrolyte composition on the ORR rate. Specifically, in acidic media the concentration of non-specifically adsorbed anions (such as perchlorate and methanesulfonate), and in alkaline media the concentration of non-specifically adsorbed cations (such as the alkali cations), have a significant effect on the ORR rate on Pt(111), which does not follow the traditional thermodynamic descriptor. To this end, we have introduced a kinetic descriptor, namely the kinetic rate of the *O to *OH transition, which can be estimated from the reversibility of the *O ↔ *OH transition on the (111) terrace. This kinetic descriptor tracks well the observed changes in the ORR rate with the concentration/identity of anions, cations and ionomers on Pt(111) surfaces ( Supplementary Fig. 8). We also measured a higher ORR activity on polycrystalline Pt electrodes in a lower concentration of HClO 4 ( Supplementary Fig. 9), showing that the effect also transfers to more practical surfaces.
This observation requires a discussion of the molecular basis for this kinetic descriptor. In the classical mechanism of ORR on Pt surfaces, equations 1-4, the transition from *O to *OH is the penultimate reaction step. In the prevalent thermodynamic model, the parameter that determines the rate of ORR is the thermodynamics of the last step, namely the conversion of *OH to water, that is the binding energy of *OH. The weaker this binding, the more free Pt sites will be available for the ORR reaction at a given potential. As mentioned, this descriptor works well when changes in the electronic structure, for instance by alloying, lead to changes in the potential of the *OH ↔ H 2 O transition 28 . However, it is important to note that the onset of ORR, say 0.95 V RHE , is in the potential window where the Pt(111) surface is still almost completely covered with the *O adsorbate. One may wonder what exactly this free site is on which ORR should take place, when this *O adsorbate just starts to be reduced to *OH. Also, as the onset of ORR is in the potential window where *O covers the surface, it becomes logical to expect that the rate at which this adsorbate is converted to *OH co-determines the ORR rate. Indeed, DFT calculations by Sakong et al. suggest that there is a competition between step 3 and step 4 for the RDS of ORR, and the energetics of step 3 is sensitive to electrochemical environment 53 . One could argue that although the final step may be the (main) potential-determining step of the overall reaction, the preceding step can still be partially rate-determining. In general, it is unlikely that only one step in a mechanism fully controls the overall rate 54 . If we accept that the rate of this step co-determines the overall rate, then it is reasonable that it is related to the rate of the *O ↔ *OH transition observed in the blank voltammetry, in the absence of oxygen. An important assumption here is that the *O ↔ *OH transition observed in the blank voltammetry is the same as the reaction in equation 3 in the ORR mechanism, or at least that these reactions have similar kinetic pathways. It is to be expected that under ORR conditions, the actual *O coverage is higher than in the absence of oxygen in solution, and it may therefore be that the *O intermediate formed during ORR is not exactly the same as the *O formed during the blank voltammetry. A second important question is why this *O ↔ *OH transition is slow or kinetically irreversible, and why this rate is influenced by the concentration of non-specifically adsorbed anions or cations? First of all, it is important to nuance the term non-specifically adsorbed. We generally consider anions such as perchlorate and methanesulfonate as non-specifically adsorbed because they do not chemically interact with the platinum metal surface. However, there are several reports that have shown that once an *OH adlayer is formed on Pt(111), this induces a weak but distinguishable interaction with perchlorate 24,25 . A similar statement holds for the effect of cations and their interaction with the *OH layer. Marković et al. have termed this latter interaction non-covalent 23 . In recent DFT calculations, we have shown that *OH and near-surface cations compete for water   56,57 . Clearly a more detailed study of the kinetics of the *O ↔ *OH transition will be needed to further elucidate the true nature of its slow kinetics. For the purpose of this paper, it suffices to reiterate our key assumption that its kinetics reflects the rate of equation 3 in the ORR mechanism, and this step is at least partially rate-determining in the overall ORR rate. Further microscopic understanding of ORR on Pt is limited by the lack of knowledge on the exact structure of *O reactant in step 3. DFT studies found there co-exists three different *O species on Pt(111) at the on-set potential 58 . It, however, remains unknown which of these O species is (directly or indirectly) involved in the ORR. Future experimental and computational clarification of this aspect would permit more realistic modelling for this reaction. Finally, our results on the stepped Pt surfaces show that the ORR rates on these surfaces can be understood as the sum or combination of the ORR rates on two different sites: A-type step-related sites and B-type terrace-related (111) sites. The ORR rate on the A sites is dominated by the traditional thermodynamic descriptor, and under acidic conditions, these sites are more active than B sites, and hence the thermodynamic descriptor works well in explaining the activity trends in acid. However, in alkaline solution, cations block the A sites, and render them less active than the B sites. The ORR rate on the B-type (111) sites are dictated by the kinetic descriptor as introduced here. As a result, in alkaline media, Pt(111) is more active than stepped Pt surfaces. This simple model of two different descriptors for the A and B sites solves the paradox of the different ORR activity trends on stepped Pt electrodes in acidic and alkaline conditions. In conclusion, we have reported here the role of non-specifically adsorbing anions in suppressing the kinetics of ORR on Pt surfaces in acid. This anion effect is rationalized by the proposed descriptor -the reversibility of the *O ↔ *OH transition on the (111) terrace, which is accessible from voltammetry. This descriptor tracks the ORR activity dependences on the concentration/identity of anions, cations and ionomers on Pt surfaces. We have proposed an enhanced model for ORR on the basis of the traditional thermodynamic descriptor and a kinetic descriptor, which rationalizes the different structure sensitivity of ORR activity on Pt surfaces in acid versus alkaline media. Our findings provide a more comprehensive model for ORR on Pt catalysts, which could potentially aid closure of the performance gap between half-cell and MEA measurements by considering the electrolyte effect and improvement of ORR activity using the upgraded ORR model.

Methods
Electrochemical cells and electrolytes. Electrochemical measurements were performed in a glass cell (for all acidic electrolytes) and a fluorinated ethylene propylene electrochemical cell (for all alkaline electrolytes). Prior to each measurement, all cell parts were cleaned by first immersing in a mix solution of H 2 SO 4 (Sigma-Aldrich, 95.0-97.0%) and KMnO 4 (Sigma-Aldrich, ≥ 99.0%) overnight, then storing in a mixed solution of H 2 SO 4 and H 2 O 2 (Merck KGaA, 35%) for at least 2 hours, and finally boiling in ultra-high purity water (Merck Milli-Q ® IQ 7000, 18.2 MΩ·cm at 298 K) at least five times. Electrolytes were prepared with ultra-high purity water and concentrated perchloric acid (traceSELECT, Fluka), concentrated methanesulfonic acid (Merck KGaA) or concentrated sodium hydroxide (Suprapur, Merck). Either disk-or bead-type platinum single-crystal electrodes were used as working electrodes in the hanging meniscus configuration. A flame-annealed platinum wire and a reversible hydrogen electrode were used as counter and reference electrode, respectively.
Single-crystal electrodes. Single-crystal Pt(111) and stepped electrodes, including Pt(151514), Pt(554) and Pt(553) were prepared by first flame-annealing with butane torches for 2 minutes, then quickly transferring to a cooling cell in an Ar/H 2 atmosphere of 3/1 (for Pt(111)) and 1/1 (for stepped Pt surfaces). After cooling to room temperature, the electrodes were dipped and covered with a droplet of ultra-high pure water for protection, before being transferred into the electrochemical cell for measurements. The Nafion coating solution was prepared by diluting commercial Nafion solution (Sigma-Aldrich, 5%) by 1,000 times. The coating solution (10 μl) was then added to the protective water droplet of Pt(111), and subsequently dried in a flow of Ar gas before electrochemistry tests.
Electrochemical measurements. Electrochemical tests were performed on a Biologic VSP-300 potentiostat using a three-electrode system. All potentials are reported against the RHE. The CVs were recorded in Ar-saturated electrolytes between 0.07 V and 0.9 V or between 0.07 V and 1.15 V (for extended CVs) at various scan rates, and reported after iR correction. A minimum scan rate of 10 mV s −1 was chosen to avoid interference from trace amounts of contaminants. A blank CV of Pt(111) was always pre-recorded to assure the cleanliness and reproducibility of testing set-ups. We plotted the charge profile of *OH peak by integrating blank CVs, after double-layer correction. Specifically, we subtracted the lowest current density located at ~0.55 V (chosen as double-layer charging current). For ORR experiments, the single-crystal electrodes were mounted on a commercial rotator (Pine Instruments) as the working electrode. The ORR performances were assessed by recording CVs from 0.1 V to 1 V at 20 mV s −1 in O 2 -saturated electrolytes at a rotating rate of 1600 rpm, with the positive-going curves being used for activity determination ( Supplementary Fig. 1). Kinetic currents were calculated via the Koutecky-Levich equation: I k = (I lim × I)/(I lim − I), where I lim is the limiting current and I is the measured current at a given potential (either 0.9 or 0.93 V were used in this study). Only polarization curves with I lim approaching the theoretical value (variation < 5%) were considered to be valid. The specific activity was obtained by normalizing the calculated kinetic current to the corresponding geometric surface area, assuming a roughness factor of 1 for all single-crystal electrodes.
The temperature-dependent measurements were performed by placing the electrochemical cell in a temperature-controlled water bath. A leak-free Ag/AgCl electrode was used as the reference electrode, which was calibrated with hydrogen evolution/oxidation polarization curve of a Pt electrode for each temperature. The calculation method for activation energy follows the work by Paulus et al. 59 . The ORR overpotential of each temperature was determined from the corresponding measured potential in RHE scale and the reversible H 2 :O 2 cell potential.

Data availability
The data that support the findings of this study are available from the corresponding author upon reasonable request.