Introduction

Air pollution is a momentous global issue, the greatest environmental hazard to human health, and responsible for approximately one in every nine deaths each year1. It is of particular concern in urban areas, where elevated pollutant concentrations and potential sufferers converge2,3,4. This is intensified by projected global population growth5, increased urbanisation1 and impacts of climate change on atmospheric conditions and weather variability6.

Beyond the myriad policy, technological and cultural changes required for the curtailment of emissions at the source, the mitigation of ongoing ambient air pollution is essential in order to reduce human exposure7. Appropriate green infrastructure (GI) is broadly recognised as one of several promising passive control systems for air pollution, and the literature detailing the positive effects that plants and vegetation may have on air quality is substantial (Table 1). Gallagher et al.8 highlight the concomitant benefits of employing porous (green) as opposed to solid barriers (including walls and parked cars) to mitigate air pollution where possible. Numerous studies involving GI corroborate its cost-effective multifunctionality by virtue of the variety of ecosystem services that may be achieved or enhanced, including ambient cooling and microclimate regulation (which bears additional gains in reducing local energy consumption and related emissions)9,10, storm water attenuation9, improved mental and physical health11,12,13,14,15, biodiversity support9, and climate change mitigation and adaptation16,17,18. This latter aspect is particularly significant with regards to air quality. In an article on the intricate, intertwined relationship between air pollution and climate change, Tibbetts6 suggests that combating one often supports abatement of the other.

Table 1 Summary of perspectives, review articles and reports on GI design and/or interactions with air pollution.

There are contrasting definitions of GI both between and within research disciplines19. This review concerns the use of trees and shrubs to form barriers between road traffic emissions and pedestrians. The terms ‘GI’ and ‘vegetation barrier’ are henceforth used interchangeably unless otherwise indicated. Similarly, for expediency, the term ‘species’ is used to distinguish between individual plants for selection, with recognition that the plant may be more properly described as, for example, a cultivar.

Transport emissions constitute a dominant source of urban air pollution20,21,22,23, and are characterised by a range of noxious gaseous pollutants, such as carbon monoxide (CO) and nitrogen oxides (NOx), and particulate matter (PM), including black carbon (BC)21,23,24. Beyond vehicle exhaust emissions, non-exhaust but traffic-related emissions (e.g. brake wear) are considered to be significant sources of PM, which is then re-suspended by traffic-related turbulence25,26. In an examination of air pollutant trends in London between 2005–2009 and 2010–2014, Font and Fuller27 found that abatement measures in some locations were offset by changes in traffic flow; that is, that increased non-exhaust sources of coarse PM, including road wear by heavier vehicles, offset reductions in exhaust emissions. This has implications for the assumed benefit of a move towards the use of electric vehicles for ambient air quality28. Similarly, for ultrafine particles (UFPs), the relative contribution from non-exhaust sources is projected to rise as cleaner fuels are adopted26. For both fine and coarse PM, real-time respiratory deposition doses are higher for pedestrians than for those travelling by public transport or by car23. To minimise pedestrian exposure, the placement of abatement measures as near as practicable to traffic-related PM sources (i.e. proximate to the road) is recommended7,20,29,30,31, particularly for UFP deposition28.

Vegetation can be utilised to form such a roadside barrier, limiting the exposure of pedestrians to air pollution8,20,32,33,34,35. The optimum physical structure of a vegetation barrier is context-dependent and should take into account the topography of each built environment7,20. Generic barrier shape recommendations have been provided for two typical urban environments: (i) open road and (ii) built-up street canyon20,31. However, these recommendations do not account for the influence of specific plant choice, which is, therefore, a central aspect of this review.

A number of studies highlight that the interactions between individual plants and ambient air quality are complex and that species can have both positive and negative effects18,36,37,38. Willis and Petrokofsky18 indicate that an understanding of the positive and negative aspects of each considered species is crucial to successful GI design. Generic recommendations regarding species choice for air pollution abatement are provided by several sources37,39,40. However, these recommendations do not account for the suitability of each plant’s expected morphology to the appropriate barrier shape with respect to its surrounding built environment.

A vast amount of data on the morphology of individual tree species is available. For example, Hirons and Sjöman41 presented a tree selection guide that includes species-specific information on expected morphology, drawing upon findings from relevant research to date as well as practitioner experience. This guide also includes some information on the observed environmental tolerance (e.g. regarding drought) exhibited by each species. However, this work does not include cost-benefit information regarding the potential effects of each particular species on ambient air quality, nor under contrasting urban conditions at a local scale (i.e. street canyon or open-road environments). Indeed, there is an apparent lack of published sources that provide holistic guidance for practitioners and planners on species selection and vegetation barrier design for improved air quality (Table 1). Such consolidated information is imperative for the successful implementation of research outputs in practice7. To fill this gap, this review synthesises the literature to indicate recommended design and management approaches for vegetation barriers under context-specific circumstances. In doing so, it forms a vital step towards creating a complete GI implementation framework and provides a template upon which ongoing research may build, for the benefit of optimised air pollution mitigation by GI. The novelty of this review lies in its holistic approach and the robust and practical recommendations achieved thereof, with reference not only to plant and leaf traits that influence air quality but also to significant considerations regarding barrier configuration and management for sustainable air pollution abatement at roadsides.

We identified relevant research papers and review articles in Web of Science, ProQuest and Scopus, using combinations of keywords, including ‘plant’, ‘species’, ‘air pollution’, ‘air quality’, ‘green infrastructure’ and ‘vegetation’, with no restrictions on the year of publication. The search results were then refined and selected for inclusion in this review if they were written in English and concerned interactions between ambient air pollution or air quality and GI, vegetation or individual plants, with a particular focus on species-specific studies undertaken in urban environments. Interactions between air quality, vegetation and climate change were considered to be beyond the scope of this review. Finally, this list was supplemented with a number of relevant papers and reports that were already known to us.

This review extends beyond the scope of recent studies regarding air pollution abatement by GI (Table 1), providing a synthesis of findings on three essential points for effective vegetation barrier design: (i) contextual barrier dimensions and configuration; (ii) disadvantageous and advantageous vegetation traits; and (iii) species-specific suitability under contrasting UK urban environments. This novel, three-pronged approach produced a wealth of data that was subsequently integrated and refined until a clear set of substantive findings were deduced to formulate context-specific design recommendations as an accessible, pragmatic framework. The formulation of this framework comprises an important, natural progression from several highly relevant studies (Table 1). Finally, knowledge gaps that have been addressed by this analysis of the literature are summarised, and important areas for future research are identified.

Interactions between GI and air quality at different spatial scales

City scale

Vegetation is regarded as generally beneficial to air quality18,42,43. However, the relationship between vegetation and ambient air quality is complex. For descriptive purposes, the potentially beneficial influences of vegetation on air quality are broadly categorised under the processes of dry deposition and atmospheric dispersion29,42. In line with complex system dynamics, the collective impacts of these processes are manifold and context-dependent, and related phenomena emerge at different scales44,45.

Dry deposition describes the process by which pollutants are at least temporarily removed from the ambient air by interception, sedimentation, capture, and other sub-processes (for PM) or by biochemical processes (for gaseous pollutants and UFPs). The influences of vegetation on this process are discussed later, under ‘Advantageous aspects of GI for air quality’. The capacity of vegetation for the direct removal of certain pollutants is considered to be negligible at city scale, with potential pollutant removal values of only a few percent under feasible greening scenarios42. For example, vegetation is a poor sink for several gaseous pollutants, including nitrogen dioxide (NO2), deposition of which is limited to stomatal uptake and therefore tends to occur during warmer months, when NO2 is less of a hazard42. Similarly, nitric acid (NO) is poorly mitigated by vegetation, partly due to significant NO emissions from vegetated soils when compared with bare soils42.

However, the spatial scale is key45; where the majority of urban infrastructure or surfaces are grey or impermeable at city scale, specific roadside locations (i.e. local-scale environments) offer ample opportunity for planting46, and the relative potential for pollution abatement at such sites may therefore be much higher47. Moreover, an important distinction exists between pollutant removal and exposure reduction, with the latter often achievable through local-scale manipulation of pollutant concentrations and air flows rather than extirpation of air pollution7,20,36,42. For roadside environments, this requires a context-specific account of the relationship between vegetation characteristics or form, street geometry, and meteorological conditions45.

Local scale

At local scale, the potential for air pollution exposure reduction by appropriate GI is well-supported (Table 1), particularly where GI involves the physical separation of people from pollutant sources, such as by the use of vegetation barriers42,48. Indeed, numerous studies have found that vegetation can act as a physical barrier between air pollution and potential sufferers, effectively extending the distance between source and receptor7,8,20,32,35, although this function is not without provisos (see ‘Trade-offs in plant selection’). Studies on the influences of such vegetation barriers on air quality have largely concerned atmospheric dispersion, and many have compared the dispersion effects of GI with those of grey infrastructure or other non-porous barriers (Table 1). For example, Gallagher et al.8 reported that porous (vegetation) barriers can act as a passive method of air pollution amelioration by adjusting dispersion patterns in a similar manner to that which may be achieved by solid barriers.

Results from a recent study involving spatial analysis suggest that roadside GI can be implemented with minimal necessary alterations to existing urban environments46. GI may therefore be utilised as one of many ‘bridge’ tools to mitigate exposure to air pollution while advancements in policy and technology work to reduce and resolve pollutant sources for the future7. The potential effectiveness of vegetation barriers to contribute towards such GI is significant. Effective barrier design, however, entails alignment with contextual conditions.

Local-scale conditions determine optimal barrier dimensions and configuration

The optimal physical structure of a vegetation barrier is context-dependent, and should take into account the topography of each built environment in relation to local meteorological conditions20,49. This principle recognises that the effects of a vegetation barrier on pollutant dispersion, in particular, are determined by the barrier’s interactions with airflow and turbulence42. The multifarious interactions between different forms of vegetation and wind conditions in relation to street geometry are discussed in several relevant reviews (Table 1), although research in this field is ongoing and the evidence base has grown over recent years (Supplementary Table S1).

Abhijith et al.20 provide a comprehensive overview of the effects that different forms of vegetation can have on ambient air quality, depending upon the physical environment. The authors differentiate between two typical urban environments: (i) open road and (ii) built-up street canyon. In Table 2, we extrapolate recommendations from major findings by Abhijith et al.20 with regards to the use of high-level (i.e. trees, with a canopy lifted from ground level) and low-level (i.e. shrubs and hedges, with leaf cover beginning at or near ground level) vegetation for air pollution abatement under each condition. The generic nature of these recommendations is necessitated by the key point that vegetation can both promote and disrupt pollutant dispersion, by exerting additional mechanical turbulence on the one hand and decreasing turbulent kinetic energy on the other20. Further research into this system is required in order to elucidate the influences of several related mechanisms, including feedback. For example, the fluidity of vegetation shape in relation to local meteorological conditions suggests that the effects of vegetation on dispersion are dynamic in situ42.

Table 2 Generic recommendations for the physical structure of vegetation in open-road and street canyon contexts, extrapolated from Abhijith et al.20.

A distinction may also be drawn between high- and low-level vegetation in street canyons, with each bearing divergent influences upon dispersion according to aspect ratio and wind conditions (Table 2). In such environments, high-level vegetation can limit the exchange of air from above, trapping pollution at ground level29,50. Although increased deposition may offset some of the decreases in dispersion potentially caused by trees in street canyons51,52, it is generally suggested that only low-level vegetation (or, in deep street canyons, only green walls) be implemented, in order to facilitate both dispersion and deposition20.

In open-road environments, however, woody plants may be implemented to form a continuous barrier. Baldauf34 suggests that such barriers can improve pedestrian-side air quality, but due consideration must be given to critical parameters, including barrier height, thickness and porosity. For example, highly porous (low-density) vegetation barriers can reduce wind speed as it penetrates gaps, potentially resulting in pollutant accumulation downwind (i.e. within and beyond the barrier)34,53. Conversely, very low-porosity vegetation can limit pollution removal by restricting infiltration and forcing air pollutants to flow above and around the barrier or to recirculate and accumulate on the upwind or source side29,54. An optimal porosity may therefore be inferred to exist between both extremes.

Vegetation barrier design for air pollution abatement requires a mechanistic understanding of how barrier form affects the movement of air pollutants55. The provision of generic recommendations by Baldauf34 regarding barrier design supports the generalisation made by Abhijith et al.20 that the effects of vegetation in open-road environments are more reliable than those of street canyon environments, due in part to the influences of complex street canyon geometry on airflows. To establish optimal GI configuration in street canyons, pilot modelling studies should therefore be undertaken before implementation, wherever possible7,20.

Trade-offs in plant selection

The diverse influences of individual species on air quality are reflected by the immeasurable range of phenotypes. As well as consideration of the planting environment, effective plant selection for air pollution mitigation requires an understanding of the balance between beneficial and detrimental aspects of vegetation at species level and below. In the following sub-sections, we critically evaluate major findings regarding the cost-benefit nature of species selection for urban air quality management.

Disadvantageous aspects of GI for air quality

Beyond potential interruptions to atmospheric dispersion within the urban boundary layer56, vegetation can be a source of additional air pollutants, primarily in the form of biogenic volatile organic compounds (bVOCs) and pollen. Indeed, the negative impacts upon air quality associated with such emissions may counteract or even outweigh any intended pollution abatement40. In order to minimise any disadvantageous aspects, careful and contextual species selection is critical42,57.

Biogenic volatile organic compounds

bVOC emissions from vegetation constitute a substantial global source of reactive hydrocarbon gases, including, most notably, isoprene, monoterpenes, and higher terpenoids58,59. bVOCs undergo atmospheric oxidation that, when combined with NOx, forms ground-level ozone (O3), a noxious gas with acute and chronic impacts on human respiratory and cardiovascular systems60. Secondary organic aerosols can also be produced on oxidation, potentially increasing ambient PM concentrations, whose negative impacts on human health are well-supported1,61. bVOC emissions are generally low below 20 °C, but increase with temperature until peaking between 35 °C and 40 °C (plant species-specific), at which point emission rates stabilise and begin to diminish42. The incidence of bVOC emissions in the United Kingdom may therefore increase over the coming decades under projected climate change scenarios59,62.

High bVOC emissions are particularly problematic in urban areas (e.g. Ren et al.63), where elevated temperatures and anthropogenic emissions converge38. bVOC emissions are also increased by other typical urban environmental stressors, including plant tissue damage by, for example, management interventions38. Plant tissue damage may instigate additional emissions in the form of green leaf volatiles (C6 aldehydes and ketones), implying the need to minimise pruning or other ‘wounding events’ (see ‘Sustainability and species suitability’). Moreover, a recent review by Fitzky et al.59 suggests the potential for positive feedback in the form of plant tissue damage by O3. The restriction of overall bVOC emissions from urban GI is therefore crucial38, and may be achieved by judicious plant selection.

Given that the atmospheric reactivity of many bVOCs is higher than that of comparable carbon number anthropogenic VOCs, it is important to consider not only the total amount but the individual type of bVOCs emitted42,64. The emission of bVOCs that exhibit higher reactivity should be avoided first and foremost, particularly in near-road environments. For example, some sesquiterpenes can have a lifetime of just a few minutes, enabling the generation of secondary aerosols in the ambient air even where dispersion from the source is unhindered42. However, there is limited available information on the causes, means and rates of production of specific bVOCs by individual plant species59. Relevant studies have tended to focus on the two most abundant bVOCs (isoprene and monoterpenes; e.g. Benjamin and Winer65), yet up to a hundred different bVOC species bear considerable influences in the atmosphere66. A comprehensive review by Laothawornkitkul et al.66 investigated the role of bVOCs at the global scale and found that anthropogenic environmental changes, including climate change, may perturb the natural relationship between the biosphere and the atmosphere, resulting in an overall increase in future bVOC fluxes. Primary sources of isoprene and monoterpenes include several genera of common UK urban vegetation, such as Populus, Salix and Platanus (for isoprene), and Quercus, Malus and Pinus (for monoterpenes)66. Other reactive bVOCs and less reactive bVOCs (with atmospheric lifetimes of <1 day and >1 day, respectively) were grouped and categorised as such, and major emission sources of both were identified as grassland as well as typical urban vegetation genera, including Betula66.

Beyond genus, bVOC emissions can vary by several orders of magnitude between species58. In a UK-based study, Donovan et al.40 developed an Urban Tree Air Quality Score (UTAQS) that ranks trees according to their potential for pollutant deposition versus bVOC emissions, based upon different modelled tree coverage and temperature scenarios. Resultant changes in O3 under each scenario were used to indicate that high bVOC emissions by some species lead to increased (0.8–2.9%) regional O3, whereas other species facilitated a modest decrease (0.3–0.8%) in O3 at the regional scale, due to a minimal increase in bVOC emissions relative to increased deposition40. Of the 30 tree species included in the study, 7 were found to have a ‘low’ UTAQS, defined as resulting in worsened air quality compared to the control scenario via increased concentrations (<3%) of O3 and NO2 despite enhanced HNO3 deposition: Populus tremula, Quercus petraea, Quercus robur, Quercus rubra, Salix alba, Salix caprea and Salix fragilis40. These seven species are considered to be high isoprene emitters. The highest-scoring (i.e. most beneficial) species were found to be: Acer campestre, Acer platanoides, Alnus glutinosa, Betula pendula, Chamaecyparis lawsoniana, Crataegus monogyna, Larix decidua, Prunus laurocerasus and Pinus nigra40. These nine high-scoring species are low isoprene emitters, but it should be noted that some (e.g. Pinus nigra) can release significant amounts of monoterpenes40,66.

As average UK temperatures increase and while anthropogenic emissions remain high, the development of comprehensive bVOC emissions profiles for viable GI species is recommended66. However, the strict classification of plant species as positive or negative according to bVOC emissions is highly problematic67, due in part to intraspecific variation under contrasting environmental conditions16,64. Indeed, Fitzky et al59. highlight that restricting the contribution of urban GI to O3 formation is further complicated by uncertainty in the influences that new plants will bear on future urban environments. It is projected, for example, that plants selected for contemporary urban environments will reach maturity when anthropogenic NOx concentrations are greatly reduced by the prevalence of cleaner transport, rendering bVOCs defunct as a precursor of O3 or, conversely, increasing the sensitivity of urban ozone chemistry to bVOC emissions59. Advanced air chemistry transport models that accommodate physiological models will be useful in describing bVOC-NOx-O3 relationships at different spatial scales, but such approaches to date have been incomplete59.

Pragmatic methods and principles, which encourage an overall restriction of bVOC emissions without absolute exclusion of certain plants, are therefore required (e.g. Simpson and McPherson67). Given that the majority of species are low bVOC emitting, with many presenting negligible or even indiscernible emissions64, the omission of species known to be generally high bVOC emitting may be sufficient for appropriate urban GI selection in the United Kingdom. However, this consideration is primarily for large-scale (i.e. city- or regional-scale) planting initiatives28,65. At local scale, plant diversity with respect to existing or planned GI in surrounding local areas is considered to be more important for long-term resilience under a changing climate and urban landscape7,68.

Pollen

Pollen collectively describes individual pollen grains, which carry the male reproductive cells of a plant. In angiosperms, pollen is produced in the anther, whereas gymnosperms produce pollen in the male cone. Human allergic reactions to airborne pollen are 20% more likely in urban areas than in rural areas, due in part to species homogeneity and interactions between pollen emissions and existing air pollutants69,70. Cuinica et al.71 exposed pollen from three tree species (Betula pendula, Carpinus betulus and Ostrya carpinifolia) in vitro to two low levels of NO2 (~0.034 and ~0.067 ppm), and found an associated increase in human allergenicity, as well as a significant decrease in pollen fertility. In a similar study, concerning the same species, Cuinica et al.72 found that exposure to low levels of CO, O3 and SO2 can also increase the allergenicity of pollen, to varying degrees in respect of pollutant type, exposure time and plant species. These findings supplement numerous studies that indicate that the viability and chemical composition of pollen are altered by exposure even at very low levels73. However, it also appears that pollen is less susceptible when exposed to pollution in vivo, rather than in vitro, and that the susceptibility of pollen differs among plant species73. It may therefore be inferred that judicious plant selection can, to some degree, limit pollen corruption. However, further research into the influences of pollution on pollen dispersion and allergenicity is required, particularly under climate change and contrasting environmental scenarios70,73.

Male cultivars of dioecious species that rely upon wind pollination comprise the most prolific source of atmospheric pollen from woody plants41,74. The selection of species that do not fit this profile is therefore recommended for planting programmes that aim to improve air quality, particularly where vulnerable people (e.g. schoolchildren) spend their time74. This may include the selection of female cultivars or insect-pollinated species (although insects can struggle to pollinate in polluted areas75). However, it should be noted that species diversity is paramount, not only in order to support ecosystem resilience and multifunctionality but also to minimise the emissions potential of any individual species41.

A comprehensive guide to landscaping for limited allergenic pollen emissions is provided by Ogren74. This guide includes the OPALS (Ogren Plant Allergy Scale) system, which currently ranks >3000 plants on a scale of 1 (least allergenic) to 10 (most allergenic) and according to >130 positive and negative factors. Ogren74 anecdotally suggests that tall vegetation barriers on the windward side of properties may be used to limit the exposure of inhabitants to allergenic pollen. Such vegetation barriers should be constructed of species with low OPALS ratings, which excludes many species that are commonly used for hedging, including Arborvitae spp., Cupressus spp., Ligustrum spp., and male cultivars of Juniperus, Salix and Taxus spp.74.

Advantageous aspects of GI for air quality

The primary mechanisms by which vegetation may be considered to improve air quality are those concerning dispersion and deposition29. Dispersion involves the transportation and dilution of pollutants from the pollutant source, and the various roles that vegetation may play in this process were outlined earlier (see ‘Local scale’ subsection). Dry deposition describes the process by which pollutants are deposited on solid surfaces, thereby reducing ambient atmospheric concentrations. It is through its influences on deposition that vegetation may be seen as passively filtering pollutants from the ambient air. The capability of vegetation to do so is relatively high in light of its high surface area and complexity in comparison with, for example, grey infrastructure29,76. However, the potential capacity of a species for pollutant deposition is determined by the quality and sum of its individual traits36,37,77,78.

Numerous review articles and technical papers have discussed the dry deposition process, including deposition schemes used in modelling systems, as well as methods used to describe or define deposition, deposition velocity and deposited amount29,48,79,80. Significant points regarding the influences of GI on dry deposition are summarised in Supplementary Section S1; the key message is that the influence of plant variation on deposition is largely determined by related variation in plant macromorphology and in the range of traits (including leaf physiology and micromorphology) that contribute toward surface resistance (Supplementary Section S1).

The immediate physical environment also influences the value and optimal form of GI as a pollutant sink. Under field conditions, dispersion bears an inextricable influence on deposition20,77,81. Recognising this, a number of recent studies have employed various integrated dispersion–deposition approaches to investigate impacts of GI52,82,83,84,85. For example, Morakinyo and Lam86 used such an approach in a CFD-based assessment of interactions between PM concentrations and vegetation barriers. The authors concluded that there may be trade-offs between vegetation barrier design for enhanced deposition and for enhanced dispersion86. Given the comparatively modest effects of deposition82,84,87, dispersion should be prioritised under such circumstances. However, where GI is appropriately positioned and managed, deposition is an important additional mechanism87.

Vegetation traits for enhanced pollutant deposition

Because the type and size of pollutant determine its means of deposition (Supplementary Section S1), different vegetation traits will be most effective for the deposition of different individual pollutants. A majority of studies have explicitly focussed on PM, and often only on particles >1 µm (Supplementary Table S1). Further research into the influences of individual plant traits on sub-micrometre PM and individual gaseous pollutant concentrations is highly recommended. However, empirical evidence from field experiments to date supports the generalisation drawn above that dry deposition to GI is influenced by specific traits, or inherited biophysical characteristics, the most significant of which concern leaf surface area and leaf properties or functions32,36,88,89,90. As mentioned, generic recommendations regarding plant selection for pollution (particularly PM) abatement are provided by previous works (e.g. Yang et al.37, Grote et al.77 and Sæbø et al.36). Appropriate species choice may also be gleaned from outputs generated by ecosystem service forecast models, such as the increasingly popular i-Tree tools. However, such models and associated outputs currently offer limited applicability at local scale48.

Yang et al.37 developed a ranking system for 100 tree species and evaluated each according to presumed PM2.5 removal efficiency, potentially detrimental aspects, and environmental tolerances. Although the methodology used by Yang et al.37 has limitations (see ‘Coordinated recommendations for enhanced vegetation barrier design’), the included set of determinant traits (particularly leaf complexity, size, surface feature and plant type (evergreen/deciduous)) is generally supported by findings from other studies. For example, Weerakkody et al.91 found a number of beneficial leaf traits for PM capture, including, most significantly, small size, complex shape and hairy or waxy surface. Earlier, Grote et al.77 found that foliage longevity is among the most important traits for air quality, along with canopy density, water-use strategy (an element of environmental tolerance) and bVOC emissions.

Foliage longevity and leaf phenology

Foliage longevity describes the length of time that a plant remains in leaf. Evergreen species retain functional leaves throughout the year, whereas deciduous species exist without functional leaves for part of the year and typically during the winter or dry season. The foliage longevity of deciduous species varies between and within species and is influenced not only by genotype but also by environmental conditions at microscale92. Due to the significance of leaves in pollutant deposition, the length of time during which GI may be most influential upon deposition is determined by its foliage longevity. In terms of deposition, evergreen species are therefore preferable to deciduous species, and deciduous species that generally exhibit longer in-leaf seasons are preferable to deciduous species that generally exhibit brief in-leaf seasons20,36,93. However, evergreen species may be more susceptible to certain stressors (e.g. climate warming94) than deciduous species, with potential implications for sustainable ecosystem service provision.

Leaf phenology describes the timing of leaf emergence and senescence and is also subject to inter- and intraspecific variation according to genotype and environmental conditions92. Indeed, variation is such that some species (e.g. Faidherbia albida) exhibit ‘reverse’ leaf phenology, where emergence occurs when senescence would typically occur95. Such a feature may be useful in mitigating air pollution during wintertime, when urban pollutant concentrations are often highest36,42, without restricting the palette of potential species to those that are evergreen. Given a comprehensive understanding of local-scale pollutant fluxes over time, it may even be possible to select species according to the most suitable leaf phenology. However, the selection of a species according to such narrow criteria would be to disregard the complex relationship between GI and air quality, as well as complementary services provided by GI, such as microclimate regulation during warmer seasons9. Furthermore, due consideration should be given to the suitability of each species to the anticipated environmental conditions. Many Pinus species, for example, are effective for PM deposition during wintertime, but susceptible to damage by salt spray from winter road conditioning, limiting their viability for many roadside locations36. The employment of alternative evergreen species that have exhibited tolerance to salt spray (such as Taxus spp.) may therefore be more appropriate at immediate roadsides36.

Density and porosity

The influence of a vegetation barrier on the movement of polluted air is determined by its density or, inversely, its porosity34. Abhijith et al.20 and Janhäll29 both summarise research findings on the effects of leaf area index (LAI), leaf area density (LAD) and vegetation porosity on pollutant concentrations. LAI is a dimensionless metric that describes the total leaf surface area per unit ground area (m2/m2)20,29. By contrast, LAD describes the total one-sided leaf area per unit canopy volume (m2/m3)20,96. LAI and LAD are the primary density parameters used to describe the available vegetation area for deposition29, and one or the other parameter is often used to estimate barrier porosity34. Despite the uncertainty introduced by this estimation method, and the lack of comparability between results from different studies due to variation in methods used29, a number of generalisations may be drawn regarding the influences of porosity on downwind pollutant concentrations.

Where vegetation is healthy its density is determined by leaf and branching morphology41, which varies greatly between species. A recent field investigation into the influence of GI in open-road conditions on PM10, PM2.5, PM1, BC and particle number concentration (PNC) found that downwind pollutant concentrations generally reduced with an increase in LAD32. This inverse correlation is corroborated by results from a CFD modelling study undertaken by Tong et al.55, which compared the influences of six vegetation and/or solid barrier configurations on near-road particle pollutant concentrations. Tong et al.55 found that wide vegetation barriers with a high LAD, as well as vegetation–solid barrier combinations, significantly reduced downwind particle concentrations. However, results from these studies32,55 suggest variation in concentration reduction efficiencies between particle sizes, which substantiates the conclusion by Steffens et al.97 that although reductions generally increase with the LAD of a barrier, the responses are non-linear. Similarly, based upon results from various studies, Abhijith et al.20 found that an optimal shelterbelt porosity may lie within the range of 20–40% for TSP and 10–20% for PM10, implying that optimal porosity is partly determined by target pollutant.

A higher vegetation barrier density generally results in lower downwind concentrations of both PM86,98,99 and gaseous pollutants54,100. However, CFD modelling undertaken by Ghasemian et al.54 found that a LAD of 3.33 m2/m3 reduced downwind concentrations of roadway emissions (represented by a tracer gas) by 10%, whereas a LAD of 1 m2/m3 increased downwind concentrations by 15%. These findings highlight that due to fluent penetration by pollutants and the introduction of the windbreak effect, very low-density (or very porous) vegetation barriers increase downwind pollutant concentrations until a critical point is reached at which further increases in LAD reduce downwind pollutant concentrations54. On the other hand, at very high densities (or low porosities), vegetation barriers can act as an impermeable obstacle, directing air above and around the barrier and restricting opportunities for pollutant deposition29,34. Therefore, optimal vegetation barrier density for deposition may be seen as permitting infiltration without throughflow101.

Abhijith et al.20 summarise that wide, tall and low-porosity vegetation barriers reduce downwind pollutant concentrations. The individual influences of these parameters (height, width and porosity), however, are relative not only to each other but to external factors. For example, meteorological conditions affect the porosity of different vegetation types in divergent ways; results from several studies indicate that, under high wind velocity, broadleaved and coniferous vegetation exhibit a decrease and an increase in porosity, respectively20,29. This reiterates the contextual nature of optimal porosity or density, as with all other aspects of GI. Barrier height, which should generally increase with distance from the road20, may be determined according to plant species choice or by planning requirements; barrier width is limited to available planting space; and optimal density can vary somewhat with barrier width34. In respect of the non-linear relationship between downwind pollutant concentrations and increasing LAD54,97, as well as the importance of semi-permeability101, optimal barrier density may be broadly described as above average density but below absolute. Given that the LAD of most naturally occurring vegetation is 1–5 m2/m3102, and in line with findings by Ghasemian et al.54, a LAD of ~4 m2/m3 may be recommended. Indeed, such a value would be in agreement with recent findings from CFD modelling undertaken by Deshmukh et al.53, which suggested that a LAD of 3 m2/m3 or higher is needed for downwind PM reductions. However, it should be noted that the density of a species that forms part of a barrier under active management may differ considerably from that exhibited by the same species under ‘natural’ or comparatively unmanaged conditions. Furthermore, the porosity of two barriers that contain the same species and are managed in the same way will differ according to site conditions (light availability, microclimate, soil conditions, root space, etc.). Therefore, it may be more feasible to regulate the porosity of a vegetation barrier by post-planting management interventions (e.g. thinning a hedge that is too dense) than by species choice alone, on the condition that the species chosen has a propensity to reach the required density (i.e. naturally exhibits at least a moderately dense crown).

Leaf size and shape or complexity

Differences in leaf size and complexity are significant predictors of deposition, particularly for PM91. Numerous field experiments have found that species with smaller leaves tend to be more effective than species with larger leaves, which may be partly attributed to the higher perimeter/surface area ratio of smaller leaves103. For example, a recent study into leaf characteristics for traffic-related PM (PM1, PM2.5 and PM10) capture found that leaf size inversely correlated with PM accumulation, whereas there were no leaf surface characteristics that showed a clear correlation with PM accumulation across species104. Interestingly, this study found that the needles of Juniperus chinensis were the most effective leaves, despite being without leaf hairs or rough surfaces, followed by small-leaved broadleaf species104. This finding is supported by results from similar studies, which also found that coniferous (needleleaf) species generally offer higher deposition velocities than broadleaf species36,37,102,105,106. Sæbø et al.36 suggest that the long and narrow shape of needle leaves offer a thinner quasi-laminar boundary layer than that of broadleaves, which offers comparatively less resistance to deposition via a shortened diffusional path length107. Chen et al.105 concur that many conifers are generally more effective for PM accumulation and post-rainfall re-capture due to their acicular, needle-like shape.

For broadleaf species, Chen et al.105 found that leaf shape and venation did not affect PM deposition, but that micromorphological surface characteristics did. However, Leonard et al.78 found that leaf shape does influence PM deposition, albeit to a lesser extent than leaf surface characteristics. Indeed, a number of studies have found that complex leaf shapes are generally more effective than simple leaf shapes78,89,90,91,107. In an evaluation of leaf traits for PM deposition, Weerakkody et al.91 erected experimental rigs containing both synthetic and natural leaves alongside a busy road, including synthetic leaves of different shapes but with identical surface areas and surface characteristics. Weerakkody et al.91 found that complex (lobed) leaf shapes demonstrated a greater potential for PM deposition than simple (elliptical or linear) leaf shapes. The authors suggest that differences in the effectiveness of leaf shapes are related to the influences of leaf shape on air patterns around the leaf, as a result of the variable drag forces upon the leaf due to wind conditions91. The comparatively poor accumulation on elliptical leaves, despite their larger perimeter, is explained by their pliancy under wind flows and lower levels of associated turbulence, indicating that the rigidity of needle leaves may be significant in their effectiveness for deposition91. A comparison of results from several wind tunnel studies concerning particle capture efficiencies of different species, formulated by Conroy et al.108, found that Pinus nigra and Cupressocyparis leylandii were the first and second (respectively) most effective species under wind speeds of 3 m/s, but that Pseudotsuga menzeisii was the least effective species, behind nine broadleaf species. These findings highlight that it cannot be concluded that needle leaves are necessarily more effective for deposition than broadleaves. However, for PM deposition, it may be generalised that needle-like and small, complex leaves are more effective than other leaf types. Further research into the comparative effectiveness of different coniferous leaf shapes (needle-like, awl-shaped, scale, etc.) is highly recommended.

Leaf surface features

Several leaf surface features are considered to positively influence deposition. Plants whose leaves present one or more of these features, as well as any of the above-described biophysical traits, are therefore considered to be relatively effective. However, functional traits may vary substantially not only between but within species, according to microclimatic and environmental conditions77,92. Additionally, the functionality of any individual trait under any given circumstance is subject to internal or plant-specific factors, such as phenology, as well as external factors, such as ambient temperature109.

Generally, rough leaf surfaces are more effective for deposition than smooth surfaces36,88,91,103,107,110,111. For example, Weerakkody et al.91 reported a number of beneficial traits for PM capture, including, most significantly, small leaf size and complex leaf shape (macromorphological features, discussed above), as well as trichomes, epicuticular wax and surface ridges (micromorphological features). An earlier study undertaken by Zhang et al.111 utilised atomic force microscopy and scanning electron microscopy to examine influential leaf features for particle capture, and found the same micromorphological features to be significant for deposition. However, Zhang et al.111 observed a difference in significance of individual features between broadleaved and coniferous species: increased leaf micro-roughness (characterised by grooves and ridges on the leaf surface) was found to correlate with increased deposition to broadleaves, whereas stomatal density and amount of epicuticular wax were found to positively correlate with deposition to coniferous (needle) leaves. These findings were corroborated by a similar, subsequent study112.

Epicuticular wax ultrastructures were also found to be significant in PM deposition to both conifers and broadleaves by a number of other studies36,90,103,113. Grote et al.77 suggest that this may be partly due to leaf wettability, with particle concentrations significantly reduced through reactions with wet surfaces, and water-soluble pollutants such as NO2 and SO2 subject to dissolution in a water film at the leaf surface. However, the influence of wax structure and chemical composition on variation in deposition is not well understood and requires further research113,114.

There is also uncertainty in the comparative significance of stomatal traits, with disagreement between findings that indicate the importance of stomatal density (e.g. Zhang et al.111) and those that indicate the importance of stomatal size (e.g. Liang et al.115). Stomatal uptake particularly concerns the diffusion of gaseous pollutants from the air as a result of plant photosynthetic and water management processes116, although particles <2 µm can enter the stomatal cavity110. Stomata open and close in response to environmental conditions, and air pollutant removal may be enhanced by the selection of species with extensive opening periods (anisohydric species, which include Populus and some Quercus species) rather than species that shorten their stomatal opening period in response to drought (isohydric species, which include Pinus and Platanus species)77. However, the benefit of plants that exhibit the appropriate water-use strategy may be offset in some cases by increased susceptibility to harsh urban conditions (see ‘Environmental tolerance’).

Regarding the above results by Weerakkody et al.91 and Zhang et al.111, a link between leaf grooves and/or trichomes and effective particle capture is well-supported by the literature36,88,90,105,113,117,118. Chen et al.105, for example, found a clear correlation between PM2.5 accumulation and grooves and trichomes in leaves. This is supported by a chamber study, which compared deposition velocities across five plant species (see Supplementary Table S1) and found that certain leaf features, including grooves and trichomes, improved particle capture for (NH4)2SO4117.

Both Weerakkody et al.91 and Leonard et al.78 conclude that trichomes are the most effective micromorphological feature for particle deposition. Liang et al.115 found instead that groove proportion and stomata size positively correlate with PM2.5 capture amount, whereas trichomes and stomatal density were not found to be significant. Disagreement between these and other findings highlights that the single most influential surface feature across leaf types (broadleaf, needle-like, scale-like, etc.) for individual pollutant types is currently unclear and an area for further research118. However, it may be generalised that rough leaf surfaces (including grooves, ridges and trichomes) are more beneficial than smooth surfaces for particle deposition, that epicuticular wax is beneficial (particularly for deposition to conifers111,112) and that stomatal traits play a significant role that warrants further investigation. These points conform to different processes outlined in Supplementary Section S1, which highlights that different surface features will vary in influence for different target pollutants.

Findings from a recent study undertaken by Zhang et al.119 indicate that genetic modification may enable the selection and enhancement of micromorphological features for air pollution removal, as previously suggested by Lawson and Blatt116. Due to their complex leaf surface micromorphology, broadleaf species are more effective for deposition than coniferous species per leaf area, whereas coniferous species are more effective at tree scale due to a larger total leaf area110,115. However, Tiwary et al.120 illustrate that deposition does not necessarily increase with leaf area for all pollutant types, that a range of different processes, counter-processes and feedback mechanisms are at all times in operation, and that holistic species assessment systems are therefore required.

Sustainability and species suitability

To minimise any potential trade-offs, it is necessary to understand the suitability of each considered plant species to the environmental conditions of the intended planting site. In a review of the multiplex effects of urban vegetation on air quality, Leung et al.57 conclude that a holistic approach to GI design is required in order to ensure long-term benefits. Considerations include environmental tolerance and ecophysiology, both of which are discussed below. However, to support plant health, additional site-specific information must be taken into account when utilising a species selection guide. Such information would include soil conditions, root and crown growth space, the likelihood of de-icing salt spray and other environmental factors relevant to plant health and with regards to the particular stresses of urban conditions41,120.

The support of plant health, by judicious selection and GI management, minimises interruption to the provision of any air pollution mitigation services, and maximises each plant’s capacity for such services22,121. For example, pollutant removal via leaf stomatal conductance is reduced, and bVOC emissions are potentially increased, when plants are stressed45,122. However, the support of plant health is also important in order to minimise costs (in both monetary and environmental terms) associated with plant establishment and management. Plant death generates emissions through decomposition57 and through anthropogenic emissions associated with replacement, a significant amount of which may have otherwise been reduced or avoided by appropriate species selection121,123. Furthermore, the creation of gaps in a vegetation barrier due to plant death could be detrimental to pedestrian-side air quality, with increased pollutant concentrations downwind caused by the aforementioned effects of barrier porosity on airflow.

Environmental tolerance

Urban roadside environments present extremely stressful conditions for vegetation41,120,124. In outlining a performance evaluation framework for urban GI development, Tiwary et al.120 suggest that a plant’s tolerance of relevant environmental stresses should be given priority over all other functionalities as an indicator of its suitability. This point is supported by findings from numerous studies into aspects of successful plant establishment in urban areas, all of which support the principle that the viability of individual species varies with planting site conditions41,68,123,125,126,127.

Environmental conditions vary considerably between sites at all scales. This is especially true of urban environments, where unnatural topographies and physical infrastructure can present an extreme heterogeneity of ground conditions and climates at local scale68,128. However, typical stressors in roadside environments include: pests and diseases; dry or nutrient-poor soil conditions; soil compaction and root space restrictions; crown growth restrictions; waterlogging; salt pollution associated with winter road conditioning; and air pollution41,68,120,123,124.

Plant diversity is crucial to urban forest resilience, and pest and disease outbreaks pose a significant threat to what is often a limited assemblage of tree species in European cities68. Indeed, Tiwary et al.120 highlight that more than half of all street trees across Europe comprises just three to five genera, including Acer, Aesculus, Platanus and Tilia. Sjöman et al.68 conclude that urban tree planting schemes should be open to the inclusion of non-native species, where ecologically appropriate, in order to ensure the survival of diverse plants in paved environments, which are characterised by dry soil conditions under impervious surfaces and warm microclimates due to solar energy absorption. Findings from a study undertaken by Roman et al.123, in California, USA, appear to corroborate this characterisation of typical planting conditions in temperate urban areas. By monitoring plant survival over five years as part of a tree give-away scheme, Roman et al.123 found that five-year survival was partly attributable to low water-use demand in certain species, as well as stable home ownership and tree aftercare. Sade et al.129 suggest that an anisohydric water-use strategy may be beneficial when water is available and under moderately stressful conditions, but that isohydric behaviour may offer greater resistance under extreme stress (i.e. drought). This observation supports the selection of anisohydric plants for enhanced stomatal uptake of pollutants, except where prolonged periods of soil water deficiency are projected to occasionally occur. Alternatively, and with a focus on continued ecosystem service provision under dry urban conditions, Sjöman et al.130 recommend the selection of species that employ drought tolerance mechanisms as opposed to water loss avoidance strategies. Sjöman et al.130 present leaf water potential at turgor loss as a reliable measure of a plant’s ability to maintain physiological function during drought conditions. Species-specific datasets based on this measure were used where possible to inform the primary source for the drought tolerance factor in Table 441.

To determine a plant’s viability, it is important to consider the specific environment of each proposed planting site121. Unlike other environmental stressors, however, it is inherent that the stressor of air pollution is present where plants are to be selected for the purpose of air pollution mitigation. Air pollution tolerance is therefore the only plant trait that may not be selected for on an ad hoc basis, but which should instead be exhibited by every plant to be considered, albeit to varying degrees according to context. For example, although Pinus species are considered to be particularly effective for PM collection, degradation of epicuticular waxes in Pinus needles by air pollution has been observed in several studies, suggesting that Pinus species may lack long-term viability at heavily polluted sites36,131,132. Similarly, plants with low stomatal conductance can tolerate relatively high levels of gaseous pollution, but are inefficient for gaseous pollutant removal, and may therefore be better suited to locations where PM attenuation is a significant focus93. Micromorphological structures around stomata, including waxy rings and cuticular arches, may also help to protect plants against PM pollution, although further research into this is needed112.

Major phytoxic air pollutants include O3, SO2 and PM, and damage is primarily presented by leaf abnormalities133,134. However, gaseous pollutants are very quickly metabolised unless photosynthesis and membrane permeability are damaged, which means that stomatal uptake remains high while the plant remains healthy and that pollution tolerance may therefore be considered a trait that influences gaseous pollutant removal77. Numerous studies have employed an Air Pollution Tolerance Index (APTI) based on leaf attributes that are associated with greater tolerance of air and water pollution stress120,135,136,137,138,139,140,141,142,143,144. APTI requires the determination of four biochemical parameters at leaf level, which are then subjected to a formula (Eq. 1) developed by Singh and Rao145:

$${\mathrm{APTI}} = \frac{{A\left( {T + P} \right) + R}}{{10}}$$
(1)

where A is the ascorbic acid content (mg/g), T is total chlorophyll (mg/g), P is leaf pH and R is the relative water content (%). Plants with APTI values of ≤11, between 12 and 16, and ≥17 are broadly classified as sensitive, intermediately tolerant or sensitive, and tolerant of air pollution, respectively136.

This method has been used to estimate air pollution tolerance for different species around the world. However, such studies have predominantly involved specimens whose provenance differs in environmental conditions (climate, soil water and/or nutrient content, and ambient air pollution concentrations) from those of typical urban planting sites in the United Kingdom134,135,136,137,138,140,141,142,143,144. Where the above APTI method has been applied in the United Kingdom (e.g. Tiwary et al.120) or under comparable conditions (e.g. Nadgórska–Socha139), the studied range of species has been limited, and this review found no single APTI dataset for the suggestion of species relevant to UK urban sites that offers sufficient diversity. The air pollution tolerance of individual species for UK planting schemes must therefore be inferred from observation or practitioner experience41. However, air pollution damage is diverse in effects, and different species exhibit different tolerances to different types and quantities of specific pollutants, with variation in tolerance due to variation in any of the four biochemical parameters measured (Eq. 1), implying that a standardised APTI dataset may be problematic or misleading in any case41,133,134,136.

Plant morphology and ecophysiology

The morphology of a plant concerns its physical form and structure as a component of its phenotype. For the purposes of this review, morphology is discussed in terms of external or readily observable characteristics, with a particular focus on whole plant size and form, rather than, for example, leaf micromorphology. The size and structural form of GI with respect to its surrounding physical environment influence its impact upon ambient air quality, and the expected morphology of a species should therefore be considered on a site-by-site basis to ensure effectiveness as well as plant health7,32. Plant ecophysiology concerns the relationship between the exhibited traits or physiology of a given plant species and its habitat preferences or geographical distribution41. Known ecophysiological features of a species may thereby be utilised to indicate its likely suitability for a planting site41. The subsequent text exclusively concerns the selection of plants for improved urban air quality according to morphological and ecophysiological characteristics.

Morphology

The projected growth form of a species may indicate its suitability for the appropriate barrier shape given the surrounding built environment. For example, a medium-sized and lighter-crowned tree may be suitable in shallow street canyons, whereas a more compact shrub may be more suitable in deeper street canyons (Table 2). Under open-road conditions, species capable of forming a tall, dense barrier with foliage from ground level are most suitable where planting space is restricted; where space allows, two or more complementary species may be planted strategically together, such as a low-growing species (with air pollution and salt tolerance) at the roadside that is followed by rows of taller vegetation32,34.

Considering anticipated size or form at maturity can support plant health (e.g. by ensuring that appropriate growth space is available124) and thereby support effective and sustainable ecosystem service provision41,93. Moreover, species whose growth patterns naturally conform to the desired GI shape will require less maintenance, which in turn will minimise both monetary and environmental cost (e.g. due to bVOC emissions). However, some formative pruning and similar post-planting interventions, where applicable, will support the development of an appropriate and healthy form, potentially reducing long-term maintenance costs associated with, for example, tree replacement41,123. It is also worth noting that although species (and particularly cultivars) may be broadly categorised by typical size or form at maturity, such aspects vary somewhat as a function of environment, and are influenced by site-specific conditions including wind exposure or light availability41.

Ecophysiology and succession

Urban planting sites are subject to a variety of environmental stresses as well as climatic and microclimatic conditions that are atypical of natural or rural areas of the same region146. This deviation complicates plant selection for such sites, with plants that may be described as native or even of local provenance potentially rendered unsuitable68. An understanding of the ecophysiology of a species can aid in anticipating its likely viability for a site41, and as already outlined, plant health is paramount in the effective performance of GI for air pollution mitigation.

Succession is the natural process of change in the species structure of an ecological community over time. Forest succession is often generally predictable for a given community and includes the order in which different species tend to become established in new areas or following an event that creates a clearing. Early successional species, such as Betula pendula, generally thrive in open sites that may be characterised by conditions of high light and wind exposure and poor soil quality41. Late successional species, such as Fagus sylvatica, tend to be shade tolerant and thrive in humid conditions with nutrient-rich soil; these species are generally capable of eventually out-growing early successional species of their respective communities41. Recognising the successional status of individual species for selection will optimise GI establishment success rates41, which, in turn, will minimise emissions, such as from re-planting and aftercare.

Coordinated recommendations for enhanced vegetation barrier design

Whereas the optimum physical dimensions of grey infrastructure can be calculated and manufactured to a highly specific standard, vegetation barriers are fluid entities that require careful consideration not only of the costs and benefits of each particular species but also of its suitability to the proposed planting site. To aid this process, Tables 3 and 4 present an initial investigation into viable woody plant species for vegetation barriers, with a particular focus on urban environments in the United Kingdom. A decision support tool developed by Hirons and Sjöman41 was selected as the principal source for two reasons: (i) it was created by investigating species that are currently used in urban forestry, as well as species whose ecoregion is similar in constraints to those of typical urban planting environments; and (ii) it contains internally consistent, species-specific information on several factors that had been identified as significant in air pollution mitigation, such as environmental tolerances and morphological characteristics.

Table 3 Viable tree species for vegetation barriers in the United Kingdom, with trait-specific information relevant to air pollution mitigation at roadsides (to be used in conjunction with Table 4).
Table 4 Viable tree species for vegetation barriers in the United Kingdom, with trait-specific information relevant to air pollution mitigation at roadsides (to be used in conjunction with Table 3).

For reasons outlined under ‘Environmental tolerance’ and ‘Species selection’, observed air pollution tolerance was the only prerequisite by which species were shortlisted for inclusion. Similarly, due to the established objective- and context-dependency of effective GI design, it was decided not to employ a ranking system (e.g. Yang et al.37) for species or for the considered factors, but instead to present information on a range of factors whose relative significance may be determined by the user. Supplementary Table S2 explains the categorisation of each factor and the primary sources used. Supplementary Section S2 also provides further information regarding the construction, terminology and limitations of Tables 3 and 4.

Colour-coding was initially considered in order to highlight species designated: (i) potentially useful for street canyons as low-level vegetation (e.g. due to small size at maturity and with a moderate- or high-density crown; Table 2); (ii) potentially useful for street canyons as high-level vegetation (e.g. due to small or medium size at maturity and a light crown; Table 2); or (iii) suitable or commonly used for hedging (e.g. see Gilman and Watson147). However, it was instead decided that employing a colour-coding system may unintentionally suggest that recommendations are dichotomous. Trees categorised as ‘moderate density’, for example, may in fact be pruned to offer a lighter or more ‘open’ crown. Similarly, trees that are categorised as having a ‘large’ mature size may in fact be slow-growing species that respond well to pruning, such as Taxus baccata, which can often be readily shaped according to objectives. Indeed, growth rate is an important additional factor that should be considered when selecting species for air pollution abatement. Other factors to consider, some of which may have been included in Table 3 or 4 had data been available, include: species tolerance of other environmental stresses (i.e. beyond salt and drought); leaf phenology (matching complementary species may enable more consistent air pollution mitigation over the year); leaf stomatal traits (for UFP and gaseous pollutant uptake); and other parts of the plant (e.g. the petioles and bark of Rhus typhia are characterised by velvety, grey hairs, which no doubt influence its value for particle deposition).

Further research into each species should be undertaken before implementation in order to avoid potential trade-offs with ecosystem services other than air pollution mitigation45. Furthermore, there may be trade-offs between intraspecific traits that influence the overall benefit of a species (e.g. the literature indicates that T. baccata may be a beneficial species, because it is evergreen, needleleaf, has a high LAI and can be readily trained into particular dimensions, but it may be that T. baccata is too dense for optimal infiltration of pollutants29. Similarly, trade-offs exist between the selection of evergreen broadleaved, evergreen conifer, deciduous broadleaved and deciduous conifer species, with needleleaf species offering a higher surface area per plant, broadleaf species generally offering a greater number of beneficial surface characteristics per leaf area, evergreen species offering year-round benefits (or costs, conversely) and deciduous species offering greater dispersion in street canyons in winter.

Optimal vegetation barrier composition for air pollution mitigation is a function of innumerable factors, some of the most recognised of which are reflected in Tables 3 and 4. The included species therefore require testing under field conditions. Different pollutants are influenced in different ways by different species and combinations of species, and according to site-specific conditions. Ensuring that the selected species contain a combination of beneficial traits can significantly improve deposition78, and incorporating a mix of different species where possible can help to target different pollutant types.

Unfortunately, the decision to form the initial species list from those that had some observed air pollution tolerance noted in Hirons and Sjöman41 meant that a great number of viable and well-established species for screening (such as Fagus sylvatica, Carpinus betulus, Ilex aquifolium, Buxus sempervirens, etc.) were not included. This species list should be expanded to include an increasing number of species and as further research data becomes available. Improving plant diversity in urban areas is imperative for increased urban ecosystem resilience to environmental hazards including and beyond air pollution7,11,68. Furthermore, several studies have demonstrated that diversity not only in species but in vegetation type and structure is important for air quality, carbon sequestration and the sustainable provision of diverse ecosystem services128,130,148. Discouragement of monoculture planting is another reason for which it was decided that the species in Tables 3 and 4 would not be ranked.

The individual leaf surface descriptions used in Table 3 were limited by an ostensible unavailability of detailed and internally consistent data on the micromorphology of all species concerned. Further research into the leaf micromorphology of different plants that may be viable for temperate urban environments is highly recommended. Moreover, it is recommended that where studies are undertaken on the influence of micromorphology on, for example, deposition, the associated species-specific data should, where feasible, be made readily available. Although such datasets on epicuticular wax structures were found to be available (e.g. Tomaszewski and Zieliński149), it was decided not to include this data in Table 3 for the sake of practicality, given that the relative influence of different epicuticular wax structures remains uncertain.

Species selection

The species list underpinning Tables 3 and 4 offers an initial investigation into relevant species and is not exhaustive. Additional species (i.e. not included in these two tables) should be considered, given that the relevant parameters are met. Figure 1 provides a schematic representation of the species selection process that may be undertaken. The final column in Fig. 1 contains a limited series of points to consider when finally selecting for beneficial plant traits. For brevity, these points are highly simplified; for example, ‘evergreen > deciduous’ should ideally be graded to reflect that evergreen species are generally more beneficial than deciduous species with longer in-leaf seasons, which are generally more beneficial than deciduous species with brief in-leaf seasons. The diagram was constructed with PM in mind, but other features (e.g. stomatal characteristics) may be more significant for gaseous pollutants. As the final column heading indicates, each point should be considered according to site-specific needs or constraints. For example, a narrow planting site may necessitate a species with a higher crown density, whereas a site that offers ample opportunity for rows of trees parallel to the road may allow for species with more open crowns to be chosen, broadening the palette of potential species and permitting a focus on other traits, such as leaf surface features (Table 3).

Fig. 1: Schematic representation of a plant species selection process for improved air quality, with a focus on vegetation barriers and particulate pollution.
figure 1

bVOC biogenic volatile organic compound, LAD leaf area density.

Due to the extremely stressful planting conditions found in urban environments and along roadsides, we suggest a rationale of negative selection, in order to deduce a base list of suitable candidates, before finally employing positive selection for species that are expected to enhance deposition. This rationale conforms with the principle that we can more confidently describe what would be detrimental than what would be beneficial, given the context-dependency of beneficial vegetation traits77. Furthermore, it is supported by the notion that ensuring no significant deterioration in air quality is a necessary antecedent in effective species selection for improved air quality105. The selection process (Fig. 1) therefore involves four fundamental questions in the following order:

  1. (1)

    Will the species thrive under the given environmental conditions?

  2. (2)

    Do the known ecophysiological and morphological characteristics of the species complement the conditions of the urban context (street canyon or open road)?

  3. (3)

    Will the species contribute minimal emissions?

  4. (4)

    Does the species bear traits that are deemed to be beneficial for pollution abatement?

This process is intended to ensure that all significant factors are considered before a plant is selected, in accordance with the principle that functional GI may be achieved only through targeted design based upon local assessments150. Taxus baccata, for example, may be beneficial if not planted where de-icing salt spray is known to be prevalent, and if female cultivars are selected for sites near vulnerable populations (Tables 3 and 4). Similarly, Quercus suber may be unsuitable for large-scale planting schemes due to its high bVOC emissions, despite its suite of beneficial leaf characteristics; Sorbus intermedia may be a notable alternative, and observation of the 5–10% diversity principle should ensure that a number of evergreen species are also identified, which may, if planted alongside Sorbus intermedia, provide the longevity in pollution abatement that Quercus suber may have otherwise offered (Table 3). The 5–10% species diversity principle reflects substantial research indicating that no individual species should comprise more than 5–10% of a population, which is most effectively observed at city scale146.

Conclusions

Interactions between GI and air quality are part of a complex socioecological system, which makes the isolation and manipulation of functions for a specific objective (i.e. improved pollution mitigation) highly problematic. However, if the spatial scale of the intervention, the context and conditions of the planting site, and the target air pollutant type are taken into account, the selection of plants that exhibit certain biophysical traits can optimise the dispersive and depositional effects of a roadside vegetation barrier (Fig. 2). The initial investigation discussed under ‘Coordinated reccomendations for enhanced vegetation barrier design’, understood in relation to recommendations made in earlier sections on ‘Interactions between GI and air quality’, ‘Trade-offs in plant selection’ and ‘Sustainability and species suitability’, may be used by practitioners as a starting point for appropriate plant selection when designing vegetation barriers (particularly in open-road environments) for improved urban air quality. Significant findings and recommendations include:

  • GI can be utilised to reduce pollution exposure at the local scale, but active control (reduced emissions) is the most effective strategy across scales.

  • City-scale analyses of interactions between GI and air quality may generate inappropriate planting recommendations, with limitations in down-scaling due to extreme heterogeneity in local-scale conditions and inherent context-dependency in the influences of different forms of GI on ambient air quality.

  • For street canyons, the aspect ratio is critical to the appropriate GI form151. In deep street canyons (H/W ≥2), only green walls are recommended; in mid-depth street canyons (H/W 0.5–2), low-level vegetation (shrubs and low hedges) may also be implemented; and in shallow street canyons (H/W ≤0.5), small and open-crowned trees may be additionally planted on the windward side of the canyon, spaced broadly apart (Table 2).

  • In open-road environments, vegetation barriers should be implemented at the immediate roadside, with a minimum height of ~2 m and greater height required with greater distance from the road, in order to screen the pollutant flux20,29,152. Where space permits, combinations of low- and high-level vegetation (e.g. a row of trees above a contiguous hedge) should be implemented32,152. Leaf coverage should begin at ground level and extend across the entirety of the barrier29,151. LAD >3 and <5 is recommended, although density should be greater where the planting site is narrower, ensuring low porosity, or above average barrier density152.

  • Potentially detrimental aspects of GI for ambient air quality include not only the propensity of inappropriate GI forms to inhibit dispersion but the tendency of certain plants to emit high amounts of bVOCs and/or pollen. bVOC emissions are of primary concern for large-scale planting schemes, whereas pollen emissions should be considered on a site-by-site basis.

  • Foliage longevity corresponds not only with annual longevity of GI performance, but with longevity of any potentially detrimental aspects and susceptibility to environmental stresses, such as air pollution and salt.

  • Small, stiff and complex leaves tend to be more effective than larger, less rigid and less complex leaves.

  • Beneficial leaf surface features include high stomatal density or size, high epicuticular wax content (particularly for needle-like leaves) and features that increase leaf roughness (e.g. hairs, ridges or grooves), although the comparative significance of different leaf surface features and for different pollutants is not yet clear.

  • The implementation of resilient and effective GI requires careful consideration of the suitability of each plant to each site, including tolerance of relevant stressors and projected growth form.

Fig. 2: A graphical overview of vegetation barrier design for air pollution abatement.
figure 2

H/W street canyon height (H) to width (W) ratio.

This review examined the literature on GI and urban air quality, with a focus on species-specific studies, and collated findings to date in order to identify recommendations and important considerations for effective vegetation barrier design. A plant selection system was thereby formulated, and an initial investigation into viable species for UK urban sites was undertaken (Tables 3 and 4). Building upon this investigation is highly recommended, with plant diversity integral to urban ecosystem resilience. A number of other areas for future research were also identified, including: the influences of air pollution on pollen dispersion and allergenicity associated with different plant species; the influences of individual plants and plant traits (e.g. coniferous leaf shapes) on air pollution, and particularly on sub-micrometre PM and gaseous pollutants; the comparative significance of different leaf micromorphological traits for pollutant deposition; and a systems perspective on the interconnections between aspects of GI, air quality and different urban environmental conditions.