Arterial and venous peripheral vascular assessment using wearable electro-resistive morphic sensors

Peripheral vascular diseases (PVDs) represent a significant burden on global human health and healthcare systems. With continued growth in obesity and diabetes, it is likely that the incidence of these conditions will increase. As many PVDs remain undiagnosed, low-cost and easy to use diagnostic methods are required. This work uses newly developed wearable electro-resistive morphic sensors to assess venous and arterial competence in the lower limbs of 36 healthy subjects. Comparison of this HeMo device was made to currently available benchtop light reflection rheography and photoplethymography devices. Results indicate that HeMo can detect the physiological signals of interest for both chronic venous insufficiency and peripheral arterial disease and all subjects were interpreted as healthy by each system. However, measurement repeatability of HeMo was highlighted as an issue that requires further system development. Furthermore, as HeMo captures changes in a section of limb circumference due to changes in underlying blood movement, rather than at a single point, the recorded signal is typically damped by comparison. This factor should be considered in any future developments.


Qualitative analysis and comparison
A cursory comparison of PPG and HeMo recordings was performed by visually inspecting the APW for the presence of a dicrotic notch.The dicrotic notch was seen in all 108 PPG and HeMo recordings.It should be noted that presence of the dicrotic notch was expected as the arterial pulse waves were recorded from healthy subjects.None-the-less, both HeMo and PPG showed agreement and classified all subjects as healthy.Figure 4 illustrates an example of simultaneously recorded PPG and HeMo arterial pulse waves.Although the overall shape of APW looks similar for PPG and HeMo, we found that the HeMo arterial pulse recording generally look slightly damped compared to PPG arterial pulse recordings resulting in increased rise time values for HeMo recordings.

Quantitative analysis and comparison
To provide a quantitative comparison of the two methods, we compared eight features (rise time, half pulse width, three quarters pulse width, dicrotic notch to diastolic peak time, systolic peak to diastolic peak time, stiffness index, augmentation index and pulse width) of both PPG and HeMo arterial pulse recordings.Details of calculation are in the Methods section of the paper.Three APWs were averaged for each of the 36 participants for both PPG and HeMo.
Table 3 summarises extracted HeMo and PPG arterial pulse features providing the comparison of minimum (min), maximum (max), mean, standard deviation (Std), 1st quartile (1st Qu), 3rd quartile (3rd Qu), median (Med) and 95% confidence interval (95% CI) of HeMo and PPG APW features.The correlation coefficients (CC) and p value from paired t-test between HeMo and PPG APW features are also given.
Barring Pulse Width, none of the features are strongly correlated.Indeed, HeMo values are significantly different to PPG features in each case except for Pulse Width.Among the extracted features pulse width of the two sensors tend to have a very similar distribution.The broadened shape of HeMo APWs (Fig. 4) is reflected in the  Agreement between the APW features of HeMo and PPG are visualised using Bland-Altman plots, in which the mean differences of each HeMo and PPG APW feature is plotted versus their mean value (Fig. 5).The bias (mean difference of the two measurements) presents the systematic error between two measurements, and the 95% confidence intervals.Table 4 provides a summary of the bias, SD, upper and lower limits of the presented Bland-Altman plots.
No appreciable trend was found for any of the features except for half pulse width.However, due to lack of any reported threshold value for the extracted features we cannot make any claim on the agreement of HeMo and PPG features.This is because making any statement about the agreement of two variables requires the comparison of limits of agreement with a priori defined clinical limit criteria 30 .
Two separate local maximums on the distribution of half pulse width differences (Fig. 5b) can be explained with reference to the HeMo recordings in Fig. 4. The relatively dampened signal causes a discontinuity where the half pulse width could be calculated before or after the dicrotic notch in different subjects.In contrast, a better agreement is found for three quarters pulse width as it has a narrower limit of agreement, a smaller bias, and the distribution of differences more similar to a normal distribution.
The repeatability of APW features extracted from HeMo and PPG were calculated using the intra-class correlation coefficient for each feature.Table 5 provides the calculated intra-class correlation coefficients and their 95% confidence interval for the extracted features of HeMo and PPG arterial pulses.The calculated correlation coefficients show the arterial pulse features extracted from PPG are much more repeatable than HeMo.

Discussion
Venous Filling Time (VFT) was measured in thirty-six healthy volunteers using HeMo and a Light Reflection Rheography (LRR) sensor simultaneously.Qualitative comparison of the two measurements revealed similar results, with all subjects classified as healthy based on a threshold VFT of 25 s, the borderline selected to distinguish healthy and unhealthy venous systems.Quantitative comparison of VFT measurements from the two sensors showed only a moderate correlation (r = 0.47) with a mean difference of − 1.66 (Fig. 1b).A paired t-test of the two measurements highlights a systematic difference between HeMo and the LRR sensor (p = 0.01).However, this does not mean one measurement is wrong.LRR is sensitive to only one area of skin whereas HeMo effectively examines the entire leg section it encloses.
Bland-Altman plots of HeMo and LRR VFT values demonstrated a small mean bias.Limits of agreement were wide, but acceptable for the presented dataset, as it did not affect the decisions of HeMo in classifying a subject as healthy/unhealthy.
The moderate correlation coefficient between devices and the statistical significance difference found between them can be attributed to a variety of factors.The HeMo measurement area on the leg was different from the LRR sensor location.Further, HeMo uses electro-resistive polymer sensors and measures blood volume changes of the area on the leg inscribed by the cuff, whereas the LRR uses optical-based sensor and measures the amount of blood volume variation underneath the area of skin where the LRR sensor is placed.
Both LRR and HeMo suffer from repeatability and inter-rater reliability issues.As the experiment is quite short, it is feasible to take the mean of multiple measures as we have done here and ameliorate the repeatability   The inter-rater reliability problem is more difficult to solve.Automated computer selection of the start and end points may be the most effective means of ensuring a reliable reproducible measure, as even with extensive instruction the raters were quite different at times.It should also be noted that the reference method in this experiment is not the gold standard method for venous assessment.This is one of the major limitations of the presented study and comparison of HeMo with the gold standard should be applied in future validation steps of this prototype.Of course, HeMo needs to be studied in clinical settings extending our current VFT dataset to one including both control and patient subjects to define the optimal threshold/ranges to separate healthy and CVI limbs.
Arterial Pulse Waves (APWs) from thirty-six healthy volunteers were also collected simultaneously using HeMo and a photoplethysmography (PPG) sensor.The APW recordings of the two methods were visually compared and the dicrotic notch was found in all HeMo and PPG APW recordings.
To provide a quantitative comparison of recordings of the two methods, eight APW features were extracted from HeMo and PPG arterial pulse recordings and they were statistically compared.The pulse width/pulse interval extracted from the APW of the two sensors were highly correlated (r = 0.99), and their difference was not statistically significant (p = 0.62) showing that HeMo can provide an estimate of heart rate similar to the PPG estimate of heart rate.In contrast, poor or moderate correlation was found between other APW features of HeMo and PPG, and they showed statistically significant differences between each pair of APW features.
The poor/moderate correlation is due to a difference in the HeMo and PPG APW contours.This is likely due to a variety of factors, however, primary among them are the different recording locations and sensor types.HeMo APWs are recordings of changes in limb blood volume due to the pulse passing through all vessels in the recording region, whereas the PPG APW is a localised recording at the big toe.The difference in the size/ lumen of the arterial vessels in these regions can affect the shape of arterial pulse 31 .Furthermore, as HeMo is a summation of all arterial flow in the area, whereas PPG is highly specific to one region, any difference in arterial flow in adjacent vessels in the measurement region of HeMo will lead to temporal dispersion and flattening of the compound signal.The difference seen in the contours of PPG and HeMo may be partially explained by the wave steepening effect, a steepening of arterial pulse and decreasing in mean pressure with distance from the heart [32][33][34] .In other words, the shape of arterial pulse recordings at two different points of body would have looked differently even if they were both recording using the same type of sensor.Further discrepancies may be expected, as the PPG is an optical sensor while HeMo is mechanical, incorporating electro-resistive sensors.
The statistically significant difference found in the APW features of HeMo and PPG does not undermine the potential of HeMo in diagnosing of PAD.However, it does highlight that APW features may not be used interchangeably.This indicates that if HeMo is to be used to diagnose PAD, its location is important and reference values will need to be calculated as thresholds for diagnosis.
This comparison allowed us to explore the APW features of HeMo and understand how each APW feature of HeMo differs from PPG arterial pulse features.The damped shape and higher diastolic amplitude seen in the arterial pulse of HeMo resulted in higher values for most of the extracted HeMo APW features, except for stiffness index, which was lower than PPG.It should be noted that the half pulse width values for HeMo clustered in two groups and was explained by the shape of the HeMo APW in which the dicrotic notch occurs at a height close www.nature.com/scientificreports/ to the half-height of the pulse (Fig. 5).This discrepancy should be accounted for in future work, for example, by using the three quarters pulse width, which provides a more homogenous feature.Among the extracted features, rise time is the only APW feature which has been previously used to distinguish limbs with and without PAD 48 .A 95% confidence interval of PPG rise time was previously reported for healthy control subjects by Allen et al. (0.172-0.278 s) 48 .The PPG rise time 95% confidence interval was lower in our study (0.148-0.164 s).This may be due to our younger population group (age range: 18-56) compared Vol:.( 1234567890 There are a number of limitations for this work.While the stretch response of the electro-resistive sensors used here have been examined in prior work (120mm stretch) 35 , it was not focused on the expansion/contractions expected in the current work (< 10mm).However, the prior work did demonstrate good performance in the region of interest for this work.We were not able to make any statement about the agreement between the APW features of the two sensors due to lack of a priori defined clinical limit criteria for the extracted features.We also were not able to provide a comparison between the systolic amplitude of HeMo and PPG due to their different measurement units.Among the extracted features only half pulse width and rise time have been shown to correlate with vascular resistance and the clinical value of other extracted features is not yet known for PAD.There is clearly a repeatability issue for HeMo that could be improved, potentially by averaging more pulse waves or improving the sensor sensitivity.Another limitation of the presented study is that the reference method is not the gold standard for diagnosis of PAD.The gold standard is the Ankle Brachial Index and was not used in this study as its output would have merely identified the subjects as healthy and not provided a richer comparison.However, while PPG is not the gold standard, other researchers have shown that it has sensitivity of 90.6%, specificity of 88.9% and accuracy of 90.2% in diagnosing PAD in comparison to the Ankle Brachial Index 36 .The presented study only provides the comparison of APW features of HeMo and PPG in a group of healthy volunteers and does not include patients in the study population.A clinical trial with patients diagnosed with PAD and agematched controls is required to have a better understanding of its APW features, to define threshold values for each, and to investigate the diagnostic value of each feature.Additionally, the LRR device uses only one 950 nm wavelength, which, while extensively used in the community due to higher skin penetration is not an isosbestic point, nor were we able to find any conclusive comparative data to gold standard VFT measurement.Finally, the volume of tissue measured by LRR, PPG and HeMo are quite different, complicating interpretation of the results.
Overall, this work highlights the potential of wearable technologies like HeMo to provide low-cost and simplified diagnosis of both CVI and PAD.However, extensive clinical trials will be required to assess the legitimacy of this hypothesis.While the available diagnostic methods are expensive and usually reserved for patients with symptoms, HeMo is wearable, low-cost and theoretically would require minimal time and training in practice, ).All participants were provided with a participant information sheet and provided their written consent to participate in the study.All volunteers were asked to participate in the experiment wearing shorts and barefoot.Weight and height of all subjects were measured before the experiment setup, and date of birth was noted.The right leg was examined in all cases.

Hemodynamic monitor (HeMo)
A HeMo device consists of two electro resistive bands made of carbon-black impregnated rubber with a resting resistance of ~ 150 Ohms/cm (Fig. 6).The bands were sewn into the top and bottom of a stretchable fabric cuff, polarised with 100 µA, and the voltage across them summated using a differential amplifier 28 .All HeMo data has a 50 th order software non-causal (zero phase lag) IIR low-pass filter applied with a cut-off frequency of 10 Hz.HeMo arterial pulse wave data had an additional 2nd order high pass filter with a cut-off frequency of 1.4 Hz to remove any potential baseline wander.The resulting waveforms for venous filling and arterial pulse wave measurement are shown in Fig. 6.

Venous measurements
Venous Filling Time (VFT) is defined as the required time for the venous volume to reach a steady baseline after completion of an exercise [37][38][39][40][41] and is highly correlated with foot vein pressure recovery time, which requires the use of invasive measurements 42 .More accurately, VFT is the time taken from the beginning of post-exercise relaxation until the venous volume reaches an endpoint which is stable for at least five seconds 43 .A typical VFT recording is depicted in Fig. 6b.Normally, contraction of the calf muscle pump empties blood out of the venous system and results in an immediate reduction in venous pressure.Relaxation of the muscle pump allows refilling of the venous system via arterial inflow.With valvular dysfunction, refilling of the venous system occurs as a result of both arterial www.nature.com/scientificreports/inflow and the retrograde venous flow 8 .Therefore, the refill time will decrease in the presence of CVI.In other words, a shortened venous filling time represents venous incompetence 37,38,41,[44][45][46] .
It should be noted that instead of VFT, other parameters such as half refilling time, 90% refilling time, 95% refilling time and the venous filling index could be used for the assessment of venous function 24,37,39,42,44,46,[49][50][51] .Half refilling time is defined as the required time for the venous volume to reach fifty percent of its final volume, and 90% and 95% refilling time are similarly described.The Venous Filling Index (VFI) is measured by dividing venous volume, or a percentage of venous volume, by refilling time 37,39,44,49,51,52 .
HeMo was worn on the middle calf (thickest part of the calf) (Figs. 6, 7).Light Reflection Rheography (LRR) (VasoScreen 5000, Medis Medizinische Messtechnik GmbH, Ilmenau, Germany) was used as a comparator device with the LRR sensor attached to the inner side of the same leg, 10 cm above the malleolus as recommended by the device manual (Fig. 7).This positioning was optimal for recordings from HeMo and the LRR sensor and it also allowed simultaneous venous filling time measurement with the two sensors at a minimum distance from each other.Each subject was requested to sit, with the foot relaxed on the floor such that the knee created an angle of ~ 110 degrees with the chair seat.
The participants were instructed to follow an audible metronome generated by the VasoScreen device and perform ten consecutive dorsiflexion manoeuvres in a timeframe of 20 s.To reduce the likelihood of signal artefacts, participants were asked to breathe normally and refrain from talking or moving during the experiment which included the pre-exercise, exercise, and post-exercise periods.Venous filling traces were recorded simultaneously from HeMo and the LRR sensor.The experiment was repeated three times for each subject.Table 6 summarises the measurement protocol.

Arterial pulse wave measurements
Arterial Pulse Wave (APW) analysis is a non-invasive method to evaluate arterial blood flow and identify peripheral arterial insufficiency in the lower limbs.The arterial pulse signal shows the variation in blood flow with each heartbeat that goes from the heart to the limbs with a wave-like pattern 53 .The APW can be separated into three main components which, correspond to different phases of a cardiac cycle (Fig. 8a), a steep upstroke and sharp peak occurring during systole (anacrotic phase), the dicrotic notch (reflective wave) representing the closure of the aortic valve, and a gradual downslope occurring during diastole (catacrotic phase) 54 .

Qualitative interpretation of the arterial waveform
Normally, the APW appears with a dicrotic notch on the catacrotic phase and the pulse becomes delayed, distorted and diminished in the presence of PAD 36,54,55 .The amplitude of the systolic peak and the shape of the APW are two key aspects, which are commonly considered for a qualitative interpretation of the arterial waveform 8,54 .The disappearance of the dicrotic notch often represents arterial obstruction, while reduced systolic amplitude shows poor local perfusion 8,54 .Qualitative interpretation of the APW is simply done by visually comparing the   www.nature.com/scientificreports/APW to a four-level grading system (Fig. 8b), which enables the classification of the APW as normal, mild PAD, moderate PAD, and severe PAD 54,56 .

Quantitative interpretation of the arterial pulse waveform
Quantitative interpretation of the APW involves extracting a range of pulse characteristics.While patients with PAD usually have reduced systolic amplitude, which can be attributed to reduced blood volume in the microvascular bed resulting from a drop in blood pressure across a stenosis 34,36,57 , specific amplitude measurements are unreliable.As a result, our work focused on time and ratioed amplitude metrics (Fig. 6c).
Crest time or foot-to-peak rise time is defined as the time from the beginning of the APW to its systolic amplitude (Fig. 9a) and has proven to be a useful feature in diagnosis of PAD 36,53 .Delayed rise time is expected in the presence of PAD due to increased vascular resistance and reduced blood pressure as a result of stenosis 36 .
Half pulse width is the width of APW at its half height (Fig. 9b).As the systolic peak reduces and the APW becomes damped with PAD, the half pulse width is expected to become wider.Awad et al. found a positive correlation between the half pulse width and vascular resistance suggesting that the half pulse width is increased with the severity of PAD 58 .
Pulse interval or pulse width is the time between the beginning and the end of the APW (distance between two consecutive APW minimums) (Fig. 9a) 53 .Augmentation index is measured by dividing the amplitude of diastolic peak by the amplitude of systolic peak (Fig. 9c).Large artery stiffness index is defined as the ratio of a patients' height to the time interval between the systolic and diastolic peaks (Fig. 9d) 53 .It is not yet known if these three APW features (pulse width, augmentation index and stiffness index) can reveal information about the presence/absence of PAD.However, each of these features have other proven diagnostic value.For example, pulse interval represents a complete heart cycle and could be used to monitor heart rate variability 53,[59][60][61][62] .Augmentation index and large artery stiffness index have been reported to be useful for the assessment of arterial elasticity 53,63 .Additionally, the second derivative of the APW has been reported as a potential candidate for assessment of arterial distensibility 53,64,65 .Other features including three quarters pulse width (Fig. 9e) and dicrotic notch to diastolic peak time (Fig. 9f) can also be extracted from the APW..PAD Grade A is attributed to an APW with a prominent dicrotic notch and sharp systolic peak; Grade B to an APW in which the dicrotic notch has disappeared; in a Grade C APW, the dicrotic notch is absent, the systolic peak is flattened, the upslope and downslope time are decreased and almost equal.In the most severe PAD cases, Grade D, the APW amplitude is significantly decreased, upslope and downslope times are equal, or the pulse is absent.Adapted from 54 .www.nature.com/scientificreports/ Volunteers were asked to wear HeMo on the thickest part of the calf and the PPG sensor was placed on the great toe.Each subject was then asked to sit on a chair with the foot relaxed on the floor.To reduce the potential of respiration induced artifacts, participants were asked to refrain from talking or moving and asked to breathe normally throughout the experiment.
Recordings were made simultaneously from both HeMo and the PPG sensor.To synchronize data from the two devices, we asked each participant to perform a single dorsiflexion manoeuvre.The dorsiflexion manoeuvre induced artefact on both recordings providing a marker to synchronize the recordings.Two minutes of data were captured in each instance and participants were asked to perform an additional dorsiflexion to mark the end of the recording.Table 7 summarises the experiment protocol.

Data acquisition
Data from HeMo were acquired using a PowerLab data acquisition unit and LabChart software (AD Instruments Pty Ltd, Dunedin, New Zealand).LRR data were recorded with the inbuilt data acquisition unit of the VasoScreen device and associated VascularLab software.HeMo sampling rate was 1 kHz while the VasoScreen device had a sampling rate of 224 Hz.Both PowerLab and VasoScreen devices were connected to a laptop via USB.HeMo recordings were exported from LabChart to ".mat" format.The data from the LRR sensor was saved via VascularLab in a format, which could be only opened with VascularLab.Screenshots of the LRR recordings were converted to an image type dataset for further analysis.PPG APW data were saved with Vascularlab software, exported in ". csv" format and imported into MATLAB for further analysis.

Data analysis
Although the VascularLab software automatically measured the VFT of LRR recorded venous filling traces, these measurements were not necessarily correct as the software could not detect the starting point, or in most cases the endpoint, of the venous filling accurately.The VasoScreen device manual noted this issue and suggested manual editing of the auto-selected start and end points of venous refilling.
To ensure fair comparison between devices, we developed a custom Graphic User Interface (GUI), which enabled importing of the LRR and HeMo datasets and manual selection of the venous refilling start and end points.The resulting VFT measurements were automatically calculated and saved based on the selection of these points.Using this GUI, all venous filling traces recorded by the LRR sensor were imported, opened in the GUI window one by one allowing data annotation (Supplementary Fig. 1).
A similar GUI was created for APW annotation, enabling importing of the APW dataset, plotting both the APW beat and its first derivative, selecting five key points (the start and end points, systolic and diastolic peaks and the dicrotic notch) of each beat, and finally saving the coordinates of the selected points for each beat.Of note, since the dicrotic notch is the inflection point of APW, the first derivative of APW was provided to assist localisation of dicrotic notch by simply visualizing it as a local maximum (Supplementary Fig. 1).
Imported HeMo traces underwent a 50 th order software non-causal (zero phase lag) IIR low-pass filter designed using MATLAB with a cut-off frequency of 10 Hz to eliminate high frequency noise.Filtered HeMo VFT data were then opened sequentially and annotated in a similar manner to the LRR data (Supplementary Fig. 1).HeMo APW data had an additional 2nd order high pass filter with a cut-off frequency of 1.4 Hz to remove any potential baseline wander.Three arterial beats from HeMo and three corresponding arterial beats from PPG were then selected to create a dataset including 138 HeMo and 138 PPG matched epochs.As manual annotation can vary between raters and to assess inter-rater reliability, three individuals were asked to independently annotate the recordings.

Data analysis
VFT data A VFT threshold value of 25 s was used to determine if the subject exhibited evidence of CVI, this threshold was recommended by the VasoScreen Device manual.As a cursory comparison we determined if both HeMo and LRR similarly categorise the study participant.As all subjects were healthy and without any diagnosed peripheral vascular condition; we anticipated that all subjects would be classed as not having venous reflux.
Summary statistics including minimum, maximum, quartiles, mean, and standard deviation of VFT were calculated for both HeMo and LRR recordings.HeMo and LRR VFT measurements were correlated to establish the strength of connection between the two methods.Scatter plots and box-whisker plots of the measured VFT values are presented to visualize the relationship and difference between VFT measurements with the two Table 7. Summary of APW recording protocol for HeMo and PPG sensor.
Step Task

Figure 1 .
Figure 1.LRR versus HeMo VFT.(a) LRR and HeMo VFT values compared to cut-off threshold for detecting reflux.(b) Bland-Altman plot of differences between LRR and HeMo VFT measurements versus their mean values.Horizontal dotted lines represent and upper/lower 95% confidence intervals.The distribution curve shows the distribution of the mean difference between LRR and HeMo measurements.

Figure 2 .
Figure 2. VFT measurements from (a) LRR and (b) HeMo annotations for all measurements.

Figure 3 .
Figure 3. (a) LRR and (b) HeMo measurements for each subject.Values are mean of annotated values.Note: The recording time for the LRR sensor was limited to 60 s by the manufacturer.Therefore, all VFT values larger than 60 s were rounded down to 60 s to enable equivalent comparison.

Figure 4 .
Figure 4. Illustrative APW from PPG and simultaneous HeMo recording from one subject.

Figure 5 .
Figure 5. Bland-Altman plots of PPG and HeMo arterial pulse wave features.The dashed horizontal lines in each plot represent bias and 95% confidence intervals.

Figure 6 .
Figure 6.(a) HeMo device.(b) Typical venous refilling curve measured by HeMo indicating volume change due to exercise and subsequent refilling.(c) Typical arterial pulse wave measurement by HeMo with key reference points highlighted.

Step Task 1
Subject sits with the knee flexed at ~ 110-degree angle and the foot relaxed on the floor 2 HeMo placed around the middle calf of right leg 3 LRR sensor attached to the inner side of the same leg and about 10 cm above malleolus 4 Start Recording and continue recording with no manoeuvres for at least 10 s 5 Participant performs ten consecutive dorsiflexion manoeuvres synchronous with metronome audio 6 Continue recording after the exercise while the subject is asked to breathe normally and to avoid moving and talking, until refilling is complete 7 Repeat steps 4, 5 and 6 two more times Vol.:(0123456789)Scientific Reports | (2024) 14:1327 | https://doi.org/10.1038/s41598-023-50534-1

Figure 8 .
Figure 8.Typical and atypical arterial pulse waveforms (APW).(a) Indicating systolic peak (SP), dicrotic notch (DN) and diastolic peak (DP).(b) Arterial pulse wave grading system46 .PAD Grade A is attributed to an APW with a prominent dicrotic notch and sharp systolic peak; Grade B to an APW in which the dicrotic notch has disappeared; in a Grade C APW, the dicrotic notch is absent, the systolic peak is flattened, the upslope and downslope time are decreased and almost equal.In the most severe PAD cases, Grade D, the APW amplitude is significantly decreased, upslope and downslope times are equal, or the pulse is absent.Adapted from54 .

1
Ask the subject to sit on a chair with the foot relaxed on the floor 2 Place HeMo around the middle calf of right leg 3 Place PPG sensor on the big toe of the same leg 4 Start Recording 5 Ask the participant to perform one dorsiflexion manoeuvre and continue recording for two minutes 6 Ask the participant to perform one dorsiflexion manoeuvre and stop the recording

Table 1 .
Inter-rater reliability of annotations for Venous Filling Time.
difference in time-based metrics.The relative amplitude of the diastolic peak would have a corresponding effect on augmentation index values.
MethodIntra-class correlation 95% Confidence interval LRR 0.72 0.57 < ICC < 0.84 HeMo 0.33 0.13 < ICC < 0.55 Vol.:(0123456789) Scientific Reports | (2024) 14:1327 | https://doi.org/10.1038/s41598-023-50534-1 issue to some degree.However, it is clear that LRR and PPG have much better intra-class correlations.The cause of the poor performance of HeMo in this regard could be due to several factors including movement of the HeMo band during test, change in HeMo response characteristics, or increased observed physiological variation by HeMo.Either way, more detailed experimentation is required to determine and ameliorate the cause if needed.

Table 3 .
Statistical summary of PPG and HeMo arterial pulse wave features.*Denotes the p value from paired t-test of HeMo and PPG APW features.

Table 4 .
Summary of HeMo and PPG arterial pulse wave features.

Table 5 .
Repeatability of the APW features.whichmay potentially lead to its widespread use as a screening tool for the assessment of vascular function in the leg.

Subjects
Thirty-six healthy volunteers were recruited (Age 32.5 ± 10 years, Male: 26 and Female = 10).Study inclusion criteria included no history of seizures or fainting, cardiovascular disease, chronic venous insufficiency (CVI), epilepsy, deep vein thrombosis (DVT), pulmonary embolism (PE), or other haematological clotting pathologies.This study was approved by the Human Research Ethics Committee of Western Sydney University (Approval No: H11268

Table 6 .
Summary of VFT measurement protocol with HeMo and LRR.