Hybrid collagen–cellulose–Fe3O4@TiO2 magnetic bio-sponges derived from animal skin waste and Kenaf fibers for wastewater remediation

Water pollution from synthetic dyes and oil spills has a significant impact on the environment and living species. Here, we developed a low-cost, environmentally friendly and easily biodegradable magnetic hybrid bio-sponge nanocomposite from renewable resources such as collagen and cellulose (Kenaf fibre cellulose–collagen, KFCC). We loaded it with magnetic bimetallic Fe3O4@TiO2 (BFT) NPs to produce a photocatalyst material (KFCC-BFT) for the treatment of colored wastewater as well as a sorbent for oil–water separation. The characterization of the bimetallic BFT NPs by XRD, HRTEM and VSM showed the deposition of TiO2 particles onto the surface of Fe3O4 with lattice interlayers spacing of 0.24 and 0.33 nm for Fe3O4 and TiO2, respectively with ferromagnetic property. The UV–vis diffuse reflectance spectra result indicated that the band gap energy of bio-sponges decreases with the increase of the bimetallic moiety. The photocatalytic efficiency of the as-prepared magnetic hybrid bio-sponge in the degradation of crystal violet dye was up to 91.2% under visible light conditions and 86.6% under direct sunlight exposure. Furthermore, the magnetic hybrid bio-sponge was used to separate motor oil from water (> 99%) and had a high oil sorption capacity of 46.1 g/g. Investigation of the recyclability and reusability performance for 9 cycles revealed that the bio-sponge had a high sorption capacity for up to 5 cycles. Our results suggest that the bio-polymer-supported BFT hybrid nanocomposite is a cost-effective and easily biodegradable photocatalyst and has great potential for real-field environmental remediation applications.


Materials and methods
Materials.Kenaf fiber was extracted from the kenaf tree (cultivated traditionally by farmers for making ropes to tie piles of rice after harvest for storage) collected in Issakaha village, from the Korhogo region, Côte d'Ivoire (Ivory Coast).All the plant experiments were in compliance with relevant institutional, national and international guidelines and legislation.Freshly flayed hides was purchased from the local slaughterhouse, Chennai, India.Raw cowhide trimming wastes were collected from the leather processing unit at CSIR-Central Leather Research Institute, Chennai, India.Hide powder was prepared from raw cowhide trimming wastes and were treated using the conventional process to remove the unwanted hair and flesh based on our previous report 37 .All chemicals were of analytical grade and were used without any further purification.Chemicals used were sodium hydroxide (SD Fine Chem Limited, 98%), sodium chlorite (LOBA Chemie, 80%), sodium sulfite anhydrous (EMPARTA, 98%), acetic acid (SRL, 99.9%), acetone (SD Fine Chem Limited), citric acid, titanium (IV) isopropoxide (Sigma Aldrich, 97%), iron (II) sulphate (SD Fine Chem Limited, 99%), iron (III) sulphate (SD Fine Chem Limited, 75%), ammonia (Rankem), isopropanol (Qaligens, 70%), ethanol (Hayman, 100%) and nitric acid (SD Fine Chem Limited, 69-72%).
Extraction of cellulose from Kenaf fibers.Kenaf fibers were dried and cut into small pieces.20 g of dried fibers were boiled with 300 mL of 6% NaOH (w/v) for 1 h.The pre-treated fibers were washed and ground in a laboratory mixer for 3 min to produce pulp-like fibers.Then, the delignification process was carried out by bleaching the pulp-like fibers with 300 mL 0.7% (w/v) sodium chlorite at pH 4, adjusted with 5% acetic acid and boiled for 3 h.The partially lignin-free fiber residue was washed with distilled water to neutral pH.The neutralized fiber residue was boiled with 300 mL 5% (w/v) sodium sulfite for 5 h to remove the lignin completely as well as hemicellulose partially.The obtained holocellulose was boiled with 300 mL 17.5% (w/v) sodium hydroxide solution for 5 h to remove the hemicelluloses.The isolated cellulose was washed with distilled water until neutral pH and air-dried 38 .
Synthesis of magnetic BFT nanoparticles.Synthesis of Fe 3 O 4 nanoparticles.The Fe 3 O 4 NPs were synthesized by the co-precipitation method.Briefly, 250 mL of the Erlenmeyer flask containing 100 mL of 0.1 M FeCl 3 and 100 mL of 0.05 M FeSO 4 .7H 2 O were stirred for 30 min at 60 °C.Then, 25% of ammonia solution was added drop by drop until the pH reaches 10, leading to dark yellow precipitate.The obtained Fe 3 O 4 NPs were washed thoroughly with distilled water to neutral pH and separated using centrifugation for 20 min at 10,000 rpm.The purified NPs were dried in a hot air oven at 100 °C for 8 h and calcinated at 500 °C for 2 h under a nitrogen environment.
Synthesis of TiO 2 nanoparticles.For the synthesis of TiO 2 NPs using the sol − gel method, 5 mL of titanium (IV) isopropoxide was added to 20 mL of ethanol and the mixture was stirred at 500 rpm at 60 °C for 30 min.Then, a mixture of 20 mL of ethanol/water (1:1) and 2 mL of HNO 3 (72%) was added dropwise.The resulting mixture was stirred at 1000 rpm for another 3 h at 100 °C to form a gel.The obtained product was centrifuged at 10,000 rpm for 20 min.The collected pellet was washed with distilled water and then with ethanol and kept at 100 °C in a hot air oven for 8 h and calcinated at 500 °C for 2 h under a nitrogen environment.
Synthesis of magnetic BFT nanoparticles.Magnetic bimetallic Fe 3 O 4 @TiO 2 NPs were synthesized through the chemical reduction method.In this procedure, 5 mL of titanium (IV) isopropoxide was dissolved in 25 mL isopropanol.Subsequently, 0.2 g of the pre-synthesized Fe 3 O 4 NPs were added under vigorous stirring at 600 rpm for 1 h at 80 °C.To this, 100 mL of 0.1 M citric acid solution was added dropwise under continuous stirring at 300 rpm for 3 h to yield brown color precipitate (magnetic bimetallic Fe 3 O 4 @TiO 2 NPs).The obtained magnetic NPs were purified by centrifugation at 10,000 rpm for 20 min, washed with ethanol and kept at 100 °C in a hot air oven for 8 h and calcinated at 500 °C for 2 h under a nitrogen environment.
Fabrication of hybrid magnetic Kenaf fiber cellulose-collagen sponge embedded with bimetallic Fe 3 O 4 @TiO 2 NPs (KFCC-BFT).The weighed amount of organic fibers (collagen and kenaf fiber cellulose) in 1:1 proportion was dissolved in 90 mL of 0.5 M glacial acetic acid using a homogenizer (Ika, T25) at 4 °C for 10 min.The wt.% of magnetic BFT NPs was calculated based on the weight of the organic fibers and three bio-sponges were fabricated namely KFCC, KFCC-BFT5, and KFCC-BFT10 corresponding to 0, 5 and 10% (wt./wt.) of BFT in the mixture.The BFT was sonicated using Lark Probe Sonicator for 2 min and added to the organic collagen-cellulose mixture.The mixture was homogenized at 4 °C for 1 h and transferred into 12 well plates and kept in a freezer (− 40 °C) for 2 h.Then, frozen products were kept in a lyophilizer (Delvac freeze drier) for 24 h to obtain hybrid magnetic KFCC-BFT bio-sponges.
Crystal violet degradation.The photocatalytic activity of the hybrid bio-sponges was investigated by analyzing the degradation of water-soluble crystal violet (CV) dye under visible light and sunlight irradiation under ambient environmental conditions.The initial concentration of CV is 2.5 × 10 −5 mol/L.The photodegradation reaction was carried out in a 100 mL glass beaker containing 30 mL of CV dye.Before the photodegradation reaction, the glass beaker containing 30 mL of CV dye and bio-sponge was stirred for 30 min in the dark to establish adsorption-desorption equilibrium.Then, the solution was irradiated using 200 W Hg (Xe) with a medium pressure lamp (66,454 Newport Oriel Instrument) at room temperature or exposed directly to sunlight at ambient temperature for 180 min at neutral pH.The glass beaker holding the sample was held 20 cm from the light source during the irradiation procedures.At regular intervals of 10 min, samples of up to 1 mL were taken out for UV-visible examination.
Motor oil removal.The oil adsorbency of the nanocomposite was determined according to ASTM: F726-12 method 39 .A weighed dry bio-sponge (m 0 ) was placed in a beaker containing excess used motor oil and allowed to immerse for 15 min.Then, the sponge was removed and drained for 2 min and the wet weight was taken (m 1 ).The oil adsorbency as the ratio of oil adsorbed to the dry sponge weight was calculated as below.
With m 0 the initial dry sponge weight, m 1 weight of the sponge at end of the oil test and m = (m 1 − m 0 ) net oil adsorbed.The recyclability and reusability performance of the hybrid bio-sponge was also investigated according to ASTM:F726-12 using the centrifugation method.The centrifugation was carried out at 5000 rpm for 5 min at 25 °C.Additionally, the bio-sponge was added to a petri dish containing excess distilled water and 0.5 g of used motor oil in order to test the sponge's ability to absorb oil from an oil-water mixture and track the sponge in a magnetic field.With the help of a strong magnet, the sponge was moved through the petri-dish for 15 min to adsorb the oil.Then, the sponge was removed and drained for 2 min and the adsorbed oil was squeezed out.Digital photographs were taken during each stage of the process.where, k represents the constant (0.89), λ stands for the wavelength of X-ray (1.5418 nm), β denotes full width at half the maximum of the diffraction peak and θ is the Bragg angle.Dynamic light scattering measurements (DLS) of the prepared NPs were analyzed using Zetasizer Nano ZS, series ZEN 3600, Malvern Instruments to obtain the particle size.UV-vis spectra of the NPs were obtained using a UV-visible spectrophotometer (Shimadzu UV-1800).The spectrum was taken from 200 to 800 nm with a 0.5 nm scanning interval.UV-vis diffusion reflectance spectra (UV-vis DRS) of bimetallic NPs and bio-sponges were obtained in a UV-Vis-NIR spectrophotometer (Agilent technologies) to determine the band gap energy.
The morphologies of the samples were examined with a field emission scanning electron microscope (FESEM, TESCAN, model-CLARA, Czech Republic) equipped with an energy-dispersive X-ray (EDX) spectroscopy.For high-resolution transmission electron microscopy (HRTEM, JEOL JEM 3010) analysis of BFT NPs, 5 µL of the sample was dispersed in 1 mL HPLC grade ethanol using water bath sonication for 30 min and 20 µL of the dispersed NPs was coated over the copper grid and dried at room temperature.The sample was observed at 200 kV voltage using LaB6 filament.To analyze the surface compositions of the nanocomposites, X-ray photoelectron spectroscopy (XPS) was performed using the ESCALAB 250 xi, Thermo Scientific.While pore size and pore diameter were determined using the Barrett-Joyner-Halenda (BJH) approach, the surface area was estimated using the Brunauer-Emmett-Teller (BET) theory.Fourier-transformed infrared (FT-IR) spectroscopic analysis was carried out using a Jasco spectrometer (Model No-4700) for the extracted cellulose, collagen, and synthesized bio-sponge samples.The surface wettability of sponges was characterized by water contact angle and oil (hexadecane) contact angle with a 5µL droplet.The measurements were obtained with a contact angle meter (Holmar, series HO-IAD-CAM-01) at room temperature.The magnetic properties of BFT, KFCC-BFT5 and KFCC-BFT10 were measured at room temperature using a vibrating sample magnetometer (VSM, Lakshore VSM 7410S).Furthermore, the interplaner spacing value was calculated as 0.25 and 0.34 nm, which was resulting from the intense peak of the Fe 3 O 4 (311) plane and TiO 2 (101) plane, respectively.However, it is interesting to note the intensity of the peaks corresponding to the Fe 3 O 4 is lower than those of TiO 2 .This could be due to the higher amount of TiO 2 present in the bimetallic NPs compared to the Fe 3 O 4 .
The morphology of the magnetic BFT NPs was investigated by HRTEM. Figure 2a shows randomly dispersed Fe 3 O 4 NPs coated with the TiO 2 NPs.The result suggests that the magnetic BFT NPs are in aggregated form in contact with one another rather than the typical core-shell configurations.The Fe 3 O 4 and TiO 2 particles present in the bimetallic NPs seem to in the order of 20-25 nm although they are in contact aggregates.The particle size range observed here is comparable to the pristine Fe 3 O 4 and TiO 2 NP crystallite size obtained from XRD data.The HRTEM image (Fig. 2b) indicates that the lattice interlayer spacing of Fe 3 O 4 and TiO 2 is 0.24 and 0.33 nm, respectively coinciding with the (311) and (101) planes of the respective oxides, as revealed by XRD patterns 42 .The average particle size of TiO 2 NPs, Fe 3 O 4 NPs and uncalcined BFT NPs measured through DLS is 41, 250 and 391 nm, respectively as shown in Figure S1.After calcination at 500 °C for 2 h, it seems that BFT NPs got agglomerated with the increase in particle size to 703 nm.Overall, the particle size observed by DLS is much larger than the values obtained by XRD and HRTEM owing to the interaction of water molecules on the NP surface during DLS measurement.The UV-Vis absorption spectra of pristine TiO 2 , Fe 3 O 4 and BFT NPs are shown in Fig. 2c.The absorption band of pure TiO 2 NPs is in the range of 300-350 nm, which is in the UV region, while the magnetite Fe 3 O 4 NPs exhibit the absorption band at 350-450 nm between UV and visible regions.In contrast, it should be noted that the BFT NPs are characterized by a wide band between 350 and 530 nm, which appears relatively high absorption in the visible region (400-800 nm).The addition of magnetite moiety induces a red shift in the absorption edges to a longer wavelength compared to pristine TiO 2 .Fe 3 O 4 promotes the movement of electrons from the valence band to the conduction band, thus leading to a shift in TiO 2 absorption in the range of its photocatalytic response 5,17 .
Bimetallic NPs and magnetic hybrid organic-inorganic bio-sponges were characterized for their magnetic behavior using room temperature magnetization by VSM. Figure 2d shows typical S-like curves with perfect saturation magnetization indicating the ferromagnetic behavior of the bimetallic NPs and the bio-sponges.Compared to pure BFT NPs (with a saturation magnetization of 8.60 emu/g), the saturation magnetization values of bio-sponges were reduced to 1.44 and 0.86 emu/g, respectively for KFCC-BFT10 and KFCC-BFT5 nanocomposites as a function of dosage of BFT.The hysteresis loops are shown in Figures S2a and b.It is seen that both the pure BFT NPs and bio-sponges exhibit coercivity of about 118 Oe.Whereas the remanent magnetization for the BFT NPs is about 1.4 emu/g and 0.16 and 0.24 emu/g for the KFCC-BFT5 and KFCC-BFT10 nanocomposites, respectively, which behaves similar to the saturation magnetization trend.
Characterization of KFCC, KFCC-BFT5, and KFCC-BFT10.FTIR spectrum of the extracted cellulose from kenaf fiber is shown in Fig. 3a.The band at 3336 cm −1 is attributed to the O-H stretching vibration and hydrogen bond of the hydroxyl groups.The band at 2889 cm −1 is the characteristic peak for alkanes exhibiting C-H stretching vibration of CH and CH 2 asymmetric stretching in the cellulose backbone.The adsorbed water binding H-O-H band is observed at 1636 cm −1 .The absorption peak at 1341 cm −1 corresponds to CH 3 deformation.The intense band, centered at 1031 cm −1 is associated with the C-O stretching modes of the hydroxyl and ether groups in the cellulose.The band at 900 cm −1 can be attributed to the presence of β-glycosidic linkages and the small peak at 666 cm −1 is associated with the C-OH out-plane bending.It is interesting to note the disappearance of characteristics peaks at 1725 cm −1 and 1505 cm −1 corresponding to C=O stretching vibration of the acetyl groups in the hemicelluloses and the C=C stretching of the benzene ring of the lignin, respectively, indicating successful removal of these components during the cellulose extraction process.
The FT-IR spectrum of pristine collagen in Fig. 3b depicts the characteristics peaks including the amide I (C=O stretching) at 1664 cm −1 , the amide II (N-H bending couple to C-N vibration) at 1546 cm −1 , the amide III (C-N stretching and N-H bending) at 1244 cm −1 , the amide A (C-N stretching and N-H bending vibration) at 3343 cm −1 and the amide B (C-H stretching) at 3081 cm −16 .The KFCC bio-sponge spectrum shows (Fig. 3c) characteristic peaks for both pristine collagen and cellulose with few changes in some peaks.The broad band at 3343 cm −1 corresponds to the N-H stretching vibration of amide A of collagen changed as a sharp band and present at the lower wavelength of 3322 cm −1 .This result suggests that the N-H group of collagen may be involved in hydrogen bonds 43 .Interestingly, the characteristics peaks of pristine collagen corresponding to the amide I group shifted from 1664 to 1644 cm −1 , from 1546 to 1536 cm −1 for the amide II group, and the amide III group from 1244 to 1237 cm −1 , thus, indicating a blue shift of 20 cm −1 , 10 cm −1 and 7 cm −1 , respectively.These downshifts indicate a possible hydrogen bond interconnection between N-H groups of collagen and the hydroxyl OH group of cellulose 43 .
In the FTIR spectrum (Fig. 3d) of the magnetic hybrid bio-sponge KFCC-BFT10, we can observe key characteristic peaks of pure collagen and cellulose.Meanwhile, new peaks are observed at 549, 583 and 660 cm −1 corresponding to Fe-O stretching vibration of magnetite Fe 3 O 4 , Ti-O, and O-Ti-O bonds, respectively 5,12 .The presence of oxide bond peaks in the bio-sponge indicates the successful incorporation of the metal nanoparticles in the organic sponge.The surface morphology of the bio-sponges (Fig. 4a-c) shows a multi-layered sheath-like spongious architecture and a highly linked porous network structure when probed through FESEM (Fig. 4a-c).It is clearly shown from the insert images (5 μm) that the hybrid bio-sponges (Fig. 4b and c) depict relatively dense and compact structures compared to the pristine KFCC bio-sponge (Fig. 4a).Further, it can be seen from Fig. 4c that the bimetallic Fe 3 O 4 @TiO 2 NPs are tightly anchored to the surface and interior of the bio-sponge fibers possibly through hydrogen bond interaction with Fe-OH or Ti-OH 25 .In comparison to the KFCC bio-sponge (Fig. 4d), the EDX mapping images show that both organic (C, N, O) and inorganic (Ti, Fe) elements are present in the hybrid bio-sponges (Fig. 4e,f).To investigate the elemental composition, a selected region of the SEM image was taken and the EDX spectral analysis was carried out.EDX spectra results displayed in Figure S3a-c confirm the presence of Fe and Ti in the KFCC-BFT nanocomposites.The presence of C, N and O peaks indicates the main elements in the KFCC (Kenaf fiber and collagen) as shown in Figure S3a.As can be seen, the intensity of the Fe and Ti peaks is higher in the KFCC-BFT10 nanocomposite (Figure S3c) when compared to KFCC-BFT5 (Figure S3b) corresponding to the dosage of the BFT.There were no other peaks in the spectra that may be attributed to contaminants.These findings prove the high adhesion of Fe and Ti-based bimetallic nanoparticles to the KFCC surface.
The N 2 adsorption-desorption technique was employed to investigate the pore size, pore diameter and pore volume of the KFCC-BFT10 bio-sponge.As shown in Fig. 5a, KFCC-BFT10 bio-sponge exhibited characteristic hysteresis loop in the adsorption-desorption isotherm.According to IUPAC classification, the N 2 adsorption-desorption isotherm of the KFCC-BFT10 bio-sponge show type IV isotherm pattern with H3 hysteresis  www.nature.com/scientificreports/loop, which means that the KFCC-BFT10 bio-sponge belongs to typical mesoporous material.The KFCC-BFT10 bio-sponge possesses a specific surface area of 40.9 m 2 /g according to Brunauer-Emmett-Teller (BET).Pore size distribution of the KFCC-BFT10 bio-sponge (Fig. 5b) shows two maxima.A very narrow peak at 2.2 nm and a broad pore size distribution from 3 to 6 nm indicate fairly wide distribution of pores.The prepared KFCC-BFT10 bio-sponge shows pore volume of 0.042 cm 3 /g (Fig. 5c).The high surface area and pore volume obtained may provide adequate surface sites for increased photocatalytic activity and oil sorption.
The chemical composition and electronic structure of the developed photocatalyst were determined by the XPS spectra.The XPS survey spectra of KFCC, BFT and KFCC-BFT10 bio-sponge are illustrated in Fig. 6a and the core level spectra of Fe 2p and Ti 2p are shown in Fig. 6b-e.As can be seen in Fig. 6a, Fe 2p, Ti 2p, C 1s, N 1s, O 1s, and O 2s peaks are visible in the spectra of pristine BFT, KFCC and KFCC-BFT10 bio-sponge.These elemental compositions obtained for the nanoparticles, hybrid biopolymer matrix and nanocomposites through XPS analysis are concurrent with the FESEM − EDX data and further confirm that the samples are devoid of any impurities.The pristine BFT and KFCC-BFT10 bio-sponge showed two distinctive peaks of Fe 3+ 2p 3/2 and Fe 3+ 2p 1/2 in the Fe 2p spectra at 710.6 and 724.1 eV, respectively (Fig. 6b and c).It shows that the predominant form of Fe species in the nanocomposites is Fe 3+ state.Additionally, the binding energies at 713.7 and 718.4 eV in the Fe 2p spectra of pure BFT could be attributed to Fe 3+ in the spinel structure and the binding energy at 727.4 eV could be attributed to Fe 3+ bound with a hydroxyl group.However, the binding energy in the Fe 2p spectra of the KFCC-BFT10 bio-sponge is slightly changed to 713.4,719.0, and 727.5 eV, respectively.This meant that in the KFCC-BFT10 bio-sponge, the electrons could have more influence towards Fe 3+ .In the Ti 2p core level spectra of the pristine BFT10 and KFCC-BFT10 bio-sponge (Fig. 6d and e), two unique peaks at 458.4 and 464.3 eV are seen, which are attributed to Ti 2p 3/2 and Ti 2p 1/2 , respectively, indicating that the titanium is mainly presented as Ti 4+ in the anatase TiO 2 form.This is in concurrence with our XRD data and also various literature values 44,45 .www.nature.com/scientificreports/Thus, it is determined that Fe in Fe 3 O 4 @TiO 2 has an oxidation state of + 3, whereas Ti is present as tetravalent and therefore both the Fe 3+ and Ti 4+ are in oxide form rather than in pure metallic form.The O 1s core level XPS spectra of pristine BFT, KFCC and KFCC-BFT10 bio-sponges are shown in Fig. 7.The binding energy range for the O 1s peak is 528-534 eV.Oxygen can exist in two different molecular states namely O 2− and O 2 − with binding energy values of about 530 and 531.5 eV, respectively.For KFCC and KFCC-BFT10 bio-sponge, the O 1s peak appears at 530.7 and 531.5 eV, respectively.This component typically results from surface oxygen that is non-stoichiometric or OH from air.The surface O 2 present in the oxides is responsible for the existence of a peak at 532.2 eV.In the case of BFT, two peaks are observed in the core-level spectra of O 1s.The low binding energy component observed at 529.7 eV is attributed to the O 2− forming oxide whereas the peak at 530.8 eV is assigned to OH − .As can be seen, XPS data show that iron is present in the chemical state of Fe 3+ and oxygen is predominantly in the state of O 2− , thereby verifying the formation of Fe 2 O 3 .In brief, the Fe element in the KFCC-BFT10 bio-sponge is more positively charged, which would help in the regeneration of Fe 3+ and thus may stimulate the photocatalytic degradation reaction.
The band gap energy of as-prepared bio-sponges was also investigated.From Fig. 8a, it is seen that the band gap energy of collagen and KFCC sponges are similar around ~ 5.1 eV and much higher than that of the hybrid KFCC-BFT10 bio-sponge, which is ~ 2.5 eV.It is seen that the band gap energy of bio-sponge without bimetallic nanoparticles is double the band gap energy of KFCC-BFT10.The possible reason for the decrease in band gap energy could be the effective interactions of Ti-O-Fe bonds in the KFCC matrix 5,17 .This reduced bandgap energy along with the red-shifted absorption in the visible region indicates that the hybrid KFCC-BFT10 bio-sponge can be excited under visible light or direct sunlight illumination to produce more electron-hole pairs for enhanced photocatalytic degradation activity of organic pollutants.
The water contact angles of the hybrid bio-sponges are shown in Fig. 8b and c and relatively high water contact angle values were achieved after the interaction with the bimetallic nanoparticles.As the percentage of bimetallic NP in the sponge increases, the water contact angle also increases.This finding suggests that the as-prepared bio-sponges are reasonably hydrophobic.On the other hand, during the oil contact angle measurement, the oil droplet penetrated quickly into the hybrid bio-sponges and the contact angle could not be recorded.The wettability tests prove that the hybrid bio-sponges exhibit selective wettability towards water and oil.These hybrid bio-sponges can easily adsorb oil and repel water.The water contact angle for the pristine collagen-cellulose (KFCC) sponge could not be recorded because the water droplet was immediately absorbed by the sponge due to the hydrophilic property of cellulose and collagen.

Photocatalytic activity.
As-prepared bio-sponges were used to study the degradation of aqueous crystal violet (CV) dye under visible light and sunlight in the presence of H 2 O 2 .Hydrogen peroxide plays a vital role in the degradation of CV by the generation of two strong hydroxyl radicals (HO • ) [46][47][48] .The mechanism for the degradation of CV in presence of magnetic bimetallic Fe 3 O 4 @TiO 2 NPs has been described by Vinosel et al. 5 As seen in Fig. 9a, the adsorption capacity of the bio-sponge is primarily responsible for the removal of roughly 12.4% of the CV in 30 min under dark conditions, which was realised until adsorption equilibrium is established.It is observed that the sharpness and the intensity of the maximum absorption peak of CV at 590 nm decreased with extended visible illumination time followed by slight blue-shifting for the samples treated with KFCC-BFT5 and KFCC-BFT10 bio-sponges (Fig. 9b and c).The photocatalytic degradation efficiency of CV dye under visible light irradiation is 85.4 and 91.2% for KFCC-BFT5 and KFCC-BFT10 bio-sponges, respectively.After 1 h of irradiation (Fig. 10a), about 50% of CV dye has been degraded and more than 60% dye in the case of KFCC-BFT10 bio-sponge.The hybrid KFCC-BFT10 bio-sponge photocatalyst shows greater degradation efficiency of 91.2% compared to 86% using 500 mg of pure Fe 3 O 4 @TiO 2 powder photocatalyst in 500 mL water as reported by Vinosel et al. 5 As can be seen, KFCC-BFT10 bio-sponge exhibited higher degradation capability owing to the higher BFT content and hence further subjected to photocatalytic degradation under sunlight exposure.The results demonstrate 86.6% degradation of CV dye for KFCC-BFT10 bio-sponge under sunlight (Fig. 9d).As shown in Table 1, the photocatalytic degradation of the KFCC-BFT10 bio-sponge photocatalyst synthesised in this study is comparable to other similarly reported  www.nature.com/scientificreports/photocatalysts with the added advantage of easy biodegradability of the photocatalyst support.The better photocatalytic degradation obtained with KFCC-BFT10 bio-sponge can be explained by the 3D macroporous structure and the floatability behavior (low density ~ 9 mg.cm −3 ), which provide the photocatalyst the ability to ease photocatalytic oxygenation activity in the air-water interface with high induced photon and increased interaction between the hybrid magnetic NPs catalyst and CV dye due to the presence of BFT on the surface as well as the inner layers of the bio-sponge support.
Oil removal efficacy.To evaluate the sorbent performance characteristic of bio-sponge as a bio-based, easily biodegradable and eco-friendly material for oil spill removal (Fig. 10b-d), the oil adsorption capacity was investigated.From Fig. 10b, it is clearly seen that both hybrid bio-sponges exhibit a higher adsorption capacity of 41.4 and 46.1 g/g for KFCC-BFT5 and KFCC-BFT10 bio-sponges, respectively, compared to KFCC bio-sponge (37.2 g/g).This high adsorption capacity of the hybrid sponge can be corroborated by its 3D macroporous network structure and hydrophobicity.An added advantage of the developed magnetic hybrid bio-sponge is the ability to track the motion of the sponge on the surface of oil-water emulsion under a magnetic field (Fig. 10c).
It is well established that the oil sorption capacity of a sorbent is mainly governed by some physical sorption properties such as the capillary effect due to the porous structure, van der Waals forces and the hydrophobic interactions between the sorbent and oils 54 , and in the present case the tracking under magnetic field is considered as an additional factor that controls the adsorption capacity of sorbent.
The recyclability and reusability of sorbent after oil removal is an important aspect to be considered during the evaluation of performance characteristics of an adsorbent such as adsorption capacity after repeating cycles of adsorbing-removing and waste management of the sorbent after being used in the environment.The as-prepared sponges are green and easily biodegradable and thus waste management after use can be done naturally without causing any harm to human beings and the environment.The recyclability and reusability data reveal that the hybrid bio-sponge exhibits high sorption capacity even after 5 cycles, showing only a small decrease from 46.1 g/g to around 40 g/g, after which the oil sorption efficiency decreases up to around 30 g/g and remains relatively constant up to 9 cycles (Fig. 10d).During recycling, it has been noticed that the hybrid bio-sponge still contains trapped oil rendering it sticky, highly packed, and dense material after centrifugation.After each cycle, the sponge was immersed in ethanol solution 2 times for 1 h, freeze-dried and lyophilized for 24 h. Figure 10c shows that the adsorbed oil may be easily removed by squeezing out and only a small amount of oil is left in the KFCC-BFT10 nanocomposite.The KFCC-BFT10 nanocomposite could be easily separated from the oil/water mixture by forceps and used for the next run thereby demonstrating its potential for oil removal applications with recyclability.

Conclusion
In summary, an easily biodegradable collagen-cellulose-based magnetic bio-sponge loaded with bimetallic Fe 3 O 4 @TiO 2 NPs was fabricated with high potency for dye and oil removal.The structural morphology analysis by HRTEM revealed no core-shell structure but the deposition of TiO 2 nanoparticles onto the surface of magnetite Fe 3 O 4 nanoparticles.From room temperature magnetization measurement, it is found that the saturation magnetization value of bio-sponge was decreased compared to the value of pure BFT NPs and hysteresis loops with an S-like curve indicating ferromagnetic behavior of the bimetallic nanoparticles and bio-sponge.The morphology of the magnetic hybrid bio-sponge showed a 3D macroporous interconnection network with the BFT NPs bound on the surface and interior of the collagen-cellulose fibrous network as visualized through HRSEM.The wettability tests proved that the incorporation of the bimetallic NPs enhanced the hydrophobicity and roughness of the hybrid bio-sponges.The as-prepared bio-sponge exhibited high photodegradation activity by the removal of crystal violet dye up to 91.2 and 86.6% under visible light and direct sunlight irradiation, respectively.It is also demonstrated that a high oil sorption capacity of 46.1 g/g was achieved and the bio-sorbent can be recycled and reused up to 9 cycles.Based on the results, the as-prepared magnetic hybrid bio-sponge has a dual potential ability in wastewater remediation for dye removal and oil spill management thereby suggesting effective visible-light-driven photocatalytic application at an industrial scale. https://doi.org/10.1038/s41598-023-40520-y

Figure 2 .
Figure 2. (a) Low and (b) high magnification HRTEM images of the magnetic BFT NPs.Lattice interlayer spacings originated by the (101) crystal planes of TiO 2 and (311) crystal planes of Fe 3 O 4 are clearly observable in the high magnification HRTEM image.(c) UV-vis spectra of pristine and BFT NPs and (d) M-H curves of BFT10 (powder Fe 3 O 4 @TiO 2 ) and hybrid bio-sponges (KFCC-BFT5, KFCC-BFT10) analyzed using VSM.

Figure 10 .
Figure 10.(a) Degradation rate of crystal violet dye as a function of time.(b) Oil sorption capacity of biosponge and (c) Digital photographs demonstrating the removal of oil using the hybrid bio-sponge from oilwater mixture.(d) Recyclability of the hybrid bio-sponge for oil removal.
The crystalline structure of TiO 2 , Fe 3 O 4 and BFT NPs were examined by using a Rigaku Miniflex (II) desktop diffractometer with Ni filtered Cu Kα radiation source (λ = 1.5418 nm) in the angular range of 20° to 80° at goniometer speed of 5 °C /min at room temperature.To identify the phase of the samples, XRD results were uploaded to the Joint Committee on Powder Diffraction Standards (JCPDS) software and the report was generated.The average crystallite d-size of NPs was determined using Debye-Scherrer Equation.

Table 1 .
Comparison of different similarly reported photocatalysts and the KFCC-BFT10 bio-sponge reported in this study on the degradation performance towards dyes.