Author Correction: How to correctly estimate the electric field in capacitively coupled systems for tissue engineering: a comparative study

Capacitively Coupled (CCoupled) electric fields are used to stimulate cell cultures in Tissue Engineering. Knowing the electric field (E-Field) magnitude in the culture medium is fundamental to establish a relationship between stimulus strength and cellular effects. We analysed eight CCoupled studies and sought to corroborate the reported estimates of the E-Field in the culture medium. First, we reviewed the basic physics underlying CCoupled stimulation and delineated three approaches to estimate the E-field. Using these approaches, we found that the reported values were overestimated in five studies, four of which were based on incorrect assumptions. In all studies, insufficient information was provided to reproduce the setup exactly. Creating electrical models of the experimental setup should improve the accuracy of the E-field estimates and enhance reproducibility. For this purpose, we developed a free open-source tool, the E-field Calculator for CCoupled systems, which is available for download from an internet hosting platform.

www.nature.com/scientificreports/ those already mentioned for capacitive coupling. One aditional reported disadvantage is that the observed cellular effects result from a superposition of electric and magnetic fields. In that case the transformer like coupling (TLC) method can be used to isolate cellular effects due only to an E-Field 5 . We focused our analysis on CCoupled systems because they avoid the faradaic products that constitute a major disadvantage of DCoupled systems, and the concomitant application of a magnetic field that characterizes ICoupled systems. An extremely large span of E-Field strengths in the culture medium has been reported for CCoupled setups alone, ranging from 1.0 × 10 −5 V m −16 to 1.7 × 10 5 V m −17 . In these studies, different methods were used to estimate the E-Field strength, some of them clearly flawed. Yet, they all describe a positive effect of electrical stimulation on cell culture, and some of them are widely cited. The aim of this study is to determine the validity of the E-Field strength estimated in several CCoupled in vitro studies by comparing it with the predictions from three different modelling approaches. We aim also to present a solid methodology to estimate the E-field in CCoupled stimulation protocols, thus contributing to enhance reproducibility and helping to establish guidelines when CCoupled systems are used in TE applications.

Methods
Electric circuit model of CCoupled experimental setups. The geometry of experimental setups for capacitively-coupled electrical stimulation of cells can often be modelled as a cylindrical layered geometry, with two circular metallic plates separated from the culture medium by electrically insulating layers, typically plastic, glass or air, as shown schematically in Fig. 1a. Note that all layers have the same diameter in this model. Given the geometry of the setup, electric charge flows parallel to the axis of the cylinder. In general, each layer can be described in terms of a resistor and a capacitor in parallel (Fig. 1b) since both paths are available for flow of charge.
In this geometry, the E-Field within each layer is uniform so the resistance, R i , and capacitance, C i , of the ith layer are given by the familiar formulae, where ρ i is the resistivity of the material, ǫ r i its relative permittivity and ǫ 0 the permittivity of vacuum, A is the cross-sectional area of the cylinder and l i the thickness of the layer. The relation between the current, I, which is the same in all layers due to charge conservation, and the voltage drop in each layer, V, is given by Ohm's law (c) RC and impedance circuit models for the five layers; (d) The complete circuit can be reduced to its three most relevant components without significant loss of accuracy. Abbreviations: ele-electrode, ins-insulator, cm-culture medium, r-resistor, c-capacitor, z-impedance.
Then, the magnitude of the E-Field in a layer is given by where l i is the thickness of the ith layer.
The purpose of this section was to show that for simple geometries like the one considered here it is possible to predict the E-Field in the culture medium exactly provided that the physical parameters of the setup are known, namely the dimensions A i , l i and electrical properties ρ i , ǫ r i , and that the applied voltage has a sinusoidal waveform, which is characterized by a single frequency. In fact, the E-Field in the various layers is independent of the (constant) cross-sectional area A because the total impedance of every layer is inversely proportional to A and the E-Field is proportional to a ratio of impedances.
The model shown in Fig. 1c is also useful to understand some general features of CCoupled setups. It turns out that, in any one layer, the impedance of either the resistive or the capacitive arm is much larger than that of the other arm. For the insulating layers Z c i ≪ Z r i , whereas for the conductive layers Z r i ≪ Z c i (see Table 2 in Results section). In these cases, the equation for the impedance of the ith layer (Eq. 4) becomes Z i = Z c or Z i = Z r , respectively. In other words, in insulating layers charge flows almost exclusively through the capacitor whereas in conductive layers charge flows almost exclusively through the resistor. In addition, the impedance of the electrodes is very low due to the high conductivity of metals, so the voltage drop across them can be neglected. As a result of these considerations, the circuit in Fig. 1c can be represented, to a very good approximation, by a capacitor, a resistance, and a second capacitor in series, as in Fig. 1d and in the work of Fitzsimmons et al., Fig. 2 6 . The capacitors represent the insulating layers and the resistor the culture medium.
In setups commonly used in tissue engineering the impedance of the culture medium, Z r , is much lower than that of insulating layers, Z c , i.e., Z r ≪ Z c ≃ Z total . Consequently, the voltage drop across the culture medium is only a very small fraction of the applied voltage (see Eq. 11) and the E-Field in the culture medium is weak. This E-Field can be increased by reducing the impedance of the insulating layers, and hence the total impedance, either by decreasing the thickness of the insulating layers or by working at higher frequencies. It also follows from the equations presented above that, for a fixed capacitive impedance, the E-Field in the culture medium is practically independent of its height (reported as "thickness" in the tables ahead), provided that Z r ≪ Z c . This is because the impedance of the culture medium is proportional to the thickness of the layer, to a very good (4) www.nature.com/scientificreports/ approximation (Eq. 1), and the E-Field is proportional to the impedance (Eq. 11) and inversely proportional to the thickness of the layer (Eq. 12). Another important consequence of the low relative impedance of culture medium ( Z r ≪ Z c ≃ Z total ) is that the total impedance of the circuit is approximately equal to the impedance of the insulating layers. As a result, the circuit responds almost as a capacitor. For a capacitor with capacitance C, the relation between current and voltage is given by which is obtained by differentiating Q = CV with respect to time, where Q is the charge stored on the capacitor. The E-Field anywhere in the setup is proportional to the current I, so its magnitude is determined primarily by the rate of change of the applied voltage. For a sinusoidal applied voltage, the E-Field in the culture medium will also be sinusoidal with a phase lead of approximately 90° and a magnitude that is proportional to the product of the frequency of the sine wave and of its amplitude (Fig. 2a,b). In the case of a trapezoidal pulse, the E-Field will be non-zero only during the risetime and falltime of the pulse and is zero during the plateau. For a linear ramp, the E-Field will be proportional to the amplitude of the wave divided by the rise or fall time. Note that the rising and falling edges of the trapezoidal pulse will produce E-Fields with opposite directions (Fig. 2c,d).
More detailed information about the theory of AC circuits may be found in Physics or Electrical Engineering textbooks, [e.g., 9 Numerical approaches for calculating the electric field. Analytical. The electrical circuit model described in the previous section can be used to calculate the E-Field in the culture medium for a cylindrical geometry and a sinusoidal applied voltage. The described equations can be easily implemented in Excel, Matlab or Python, for example. When the waveform is not sinusoidal, an estimate of the maximum E-Field strength can be obtained by considering a frequency such that the maximum rates of change with time of the actual voltage The proposed analytical approach will yield estimates of the E-Field of the right order of magnitude even when the geometry is non-cylindrical, but care must be taken to choose equivalent dimensions for the cylindrical model appropriately. Specifically, the thickness of the insulating layers in the cylindrical model should be the same as in the original setup.
Circuit simulator. As an alternative to the analytical approach, it is possible to use software packages for the simulation of analogue circuits to view the temporal variation of the current or of the voltage drop in the culture medium and to estimate the E-Field strength in the region of interest. We used the freely distributed program LTspice (LTspice LVII, Analog Devices, USA) to draw a circuit like the one illustrated in Fig. 1c considering only the 3 central sections since the impedance of the electrodes is negligible. The voltage waveform was specified as a sinusoidal waveform using the SINE option, as a trapezoidal pulse using the PULSE option, or as an arbitrary waveform using the PWL (piece-wise linear) option. After running the simulation, a LTspice probe tool was used to obtain the current through the resistive branch of the culture medium, from which the voltage drop and hence the E-Field were calculated. Note that for these simulations the resistive and capacitive impedances of the various layers were calculated based on a single, matching frequency obtained as outlined in Eq. (14). The two approaches should therefore provide the same estimates for the E-Field. Additionally, this implies that the simulator does not consider the full frequency spectrum of the waveform and so the predicted temporal variations are not exact but rather good approximations of the true variations.
Finite element analysis. If the geometry of the setup makes it difficult to estimate the resistance and capacitance of the various layers, then a numerical method that considers the specific features of the geometry should be applied to obtain accurate estimates of the E-Field. In this study, we used the Finite Element (FE) method for this purpose. Specifically, the commercial program COMSOL Multiphysics (version 5.2a, www. comsol. com, Stockholm, Sweden) was used to import the setup geometry defined in SolidWorks (version 2018, Dassault Systemes SolidWorks Corporation, France) and to create an extra fine, physics-controlled volume mesh. The Electric Currents interface of the AC/DC module was used to solve the underlying partial differential equations, with the direct solver MUMPS. This interface solves Laplace's equation ∇ · (σ ∇φ) = 0 , where φ is the electrostatic potential and σ is the electric conductivity, and calculates the gradient of the scalar potential to determine the induced E-field. A Frequency Domain study was selected for sinusoidal voltages and a Time Dependent study for arbitrary waveforms. Note that no assumptions about the frequency spectrum of the voltage waveform are needed since the original waveform is used. The boundary conditions applied were Electric Potential and Ground for the two electrodes, Electric Insulation for other external boundaries and Current Conservation for internal boundaries. COMSOL can also handle ideal cylindrical geometries easily and efficiently as 2D axisymmetric models, as shown in Fig. 3. www.nature.com/scientificreports/ The three proposed approaches are based on well-known physics and well-established numerical methods and can produce accurate estimates of the E-Field for increasingly complex waveforms and geometries. They all assume that the quasi-electrostatic approximation holds.

Selection of studies and theoretical validation. A bibliographic search was performed on Sci-
enceDirect, Pubmed and Scopus databases to identify experimental studies using CCoupled stimulation. In order to narrow the search, only bone cell lineages were considered for this analysis taking into consideration our research group's interest in bone tissue engineering. The following search sentence and keywords were considered:"(capacitive stimulation) AND (bone OR osteogenic OR osteogenesis) AND (in vitro)", originating a total of 922 records, 881 in ScienceDirect, 30 in Pubmed and 11 in Scopus. After removal of duplicates, the remaining 883 records were screened considering the following exclusion (e) and inclusion (i) criteria: (e1) Publications consisting in reviews or studies in vivo, or involving implants or prosthetic device; (e2) Studies targeting biological tissues other than bone; (e3) Studies targeting cellular processes other than proliferation and differentiation; (e4) Studies using stimulation phenomena other than capacitive coupling; (i1) The geometry of the experimental setup and voltage waveform must be reported in sufficient detail to allow the construction of a reasonably accurate model; (i2) The cell culture chamber must be empty of any kind of construct and contain only cellular content and culture medium. This is because the presence of a scaffold can produce a highly non-uniform E-Field 22 ; (i3) The E-Field in the culture medium, measured or estimated, must be reported to allow a comparison with our model's predictions.
A total of 16 records fulfilled all criteria. 4 additional records fulfilling all criteria were found by hand searching the reference lists in the 16 records mentioned previously. Eight different setups for capacitive stimulation are reported in these 20 records. They are listed below and were named after the first author of the oldest reference. In all these studies the E-Field values reported were calculated, not measured. For each one of these setups, the E-Field in the culture medium was calculated using the three approaches described in the previous section. The analytical solutions were implemented in Matlab and Python. The use of LTspice is exemplified in Fig. 4 with the asymmetric sawtooth voltage waveform applied in Hartig's setup 17 . Rodan's 7 , Stephan's 19 and Khaw's 21 setups are clearly different from the ideal layered cylindrical geometry. For these setups a realistic geometry was implemented in COMSOL. Fig. 5 shows the realistic model for Rodan's setup [7], together with the layered cylindrical model with similar dimensions for analytical and circuit simulator calculations.

Results
Modelling data like the dimensions of the setup, the values of the electrical properties of the materials, and details of the voltage waveform for all eight studies are compiled in Table 1. Note that the inverse of resistivity, i.e., the conductivity, σ , is listed in this table. Reasonable estimates for missing values were obtained from the literature cited in the table. The resistance, capacitance, and reactance of the three central layers of each setup were calculated based on these values and are listed in Table 2. Khaw's setup is not listed in this table because at zero frequency the capacitive reactance of the insulators is infinite (Eq. 6), so the current through the setup and hence the E-Field in the culture medium will be zero. Note that values in this table are given with two decimal places for clarity but more decimal places were used in the calculations.
The comparisons between the values of the E-Field in the culture medium reported in the original papers and those obtained using the three approaches described in this paper methods section are listed in Tables 3 and 4. Table 3 shows that there is a good agreement between the original reported values and our theoretical estimates in the case of the studies by Brighton et al. 15 , Hartig et al. 17 and Stephan et al. 19 . In Brighton's study, the reported E-Field values obtained using analytical and FE approaches 34 agree with our estimates, for the two frequencies and applied voltages considered. The results are consistent with the fact that the E-Field is proportional to the applied voltage and that it is (approximately) proportional to the frequency. Hartig et al. reported a potential difference of 100 µ V across the cell monolayer. We assumed that the thickness of the monolayer was 25 µm 35 , which yielded an E-Field estimate of 4 V m −1 . We also had to assume a risetime of 45 ns for the asymmetric sawtooth voltage waveform, based on the specifications sheet of the function generator (Hameg HM1881-2, www. farne ll. com/ datas heets/ 318574. pdf). Given these and other uncertainties, the agreement between the reported value (4.0 V m −1 ) and our predictions (5.5 V m −1 ) is acceptable. Stephan et al. estimated the electric field strength in a 3D model of a single well using the FE approach. Since the authors did not report the thickness of the petri dish www.nature.com/scientificreports/ wall, which separates the electrodes from the cell culture medium, we assumed a typical wall thickness of 1 mm. Despite this uncertainty, a good agreement between our predictions and the reported E-Field values was found.
In general, small differences can be attributed to some of the model parameters not being described exactly in the original studies. Also, note that our three numerical approaches yield the same results, as expected.
The results concerning the studies where a discrepancy between the reported values and our estimates was observed are given in Table 4. In all cases, the E-Field in the culture medium was overestimated. In Rodan et al. 7 , no information on how the E-Field was estimated is provided. However, the slow risetime of 1.85 ms, which corresponds to a matched frequency of 86 Hz, seemed too low to produce an E-Field of 1.2 ×10 5 V m −1 . As the geometry of the setup differs from the layered cylindrical setup, a realistic model was implemented in COMSOL, as shown in Fig. 5. A layered cylindrical setup with similar dimensions was also designed to calculate resistances and capacitances for use in the analytical and circuit simulator approaches. All numerical approaches converged to a predicted field of about 6.0 ×10 −3 V m −1 , more than 7 orders of magnitude less than reported. Interestingly,    12 , only the relative permittivity of the various layers was taken into account, the electric resistivity of the culture medium was not considered. However, the resistance of the culture medium is the dominant factor affecting the E-Field in this layer. The other fundamental parameter that was missing was the risetime of the trapezoidal wave. We assumed a risetime of 7 ns based on the specifications sheet of the signal generator used Velonex 380 (https:// www. teste quipm entco nnect ion. com/ 4603/ Velon ex380. php). This assumption and others regarding the conductivity of the various layers (Table 1) lead to an estimate for the E-Field in the culture medium of 154 V m −1 for an applied voltage of 300 V by all numerical approaches used. This is one order of magnitude lower than the values reported by Korenstein et al. Estimates of the E-Field for voltages other than 300 V can be derived from the estimate presented here because the field is simply proportional to the applied voltage. In their paper, Korenstein et al. state that several experimental factors related to the electrical circuit distorted the voltage waveform, which suggest that the effective risetime may have been significantly longer than 7 ns. This would lead to a lower predicted E-field value.
The value of the E-Field reported in Fitzsimmons et al. (1.0×10 −5 V m −1 ) 6 also differs significantly from our estimate (3.0 ×10 −7 V m −1 ). This discrepancy arises from an incorrect estimate of the resistance of the culture medium: it seems that the resistivity of the culture medium (100 cm) was incorrectly assumed to be equal its resistance (100 ). We estimated the resistance of the culture medium to be about 30 times lower, which lead to a reduction in the estimated E-Field by the same factor. Also, Fitzsimmons et al. did not calculate the total impedance of the setup by summing the complex impedances of the various layers, which also lead to a small error in this value.
Griffin et al. 18 used the same setup as Hartig et al. but they did not consider the time-varying nature of the applied voltage, the Degenerate Wave (DW), nor the conductive nature of the culture medium (see 33 , supplementary Figure _ S1.docx, File _ S2.docx). To get an accurate estimate of the field we obtained values for the conductivity of the various materials from the literature and digitized the DW from figure 1 in 33 . For use in our analytical approach, we estimated that a sine wave with a frequency of 22 Hz and 100 mV amplitude would have approximately the same maximum rate of change with time as the DW. The amplitude was taken to be 100 mV because this is the amplitude of the first (positive) deflection of the DW. Our numerical approaches estimated the E-Field in the culture medium to be approximately 3.5 ×10 −8 V m −1 , more than 8 orders of magnitude smaller than the value reported by Griffin et al. Khaw et al. 21 reported to have applied E-Fields of 100 V m −1 and 200 V m −1 in their capacitively-coupled bioreactor by applying constant potential differences of 14.2 V and 28.4 V respectively. These estimates were obtained with a FE 3D model, using the electrostatics interface to compute the E-Field. The selected set of equations does not take into account the conservation of currents and Ohm's law, so it is insufficient to correctly model this CCoupled setup. As we stated in the methods section, the response of CCoupled systems is almost that of a capacitor, so the E-Field generated in the culture medium by continuous DC stimulation is effectively zero.

Discussion
The results from our comparative analysis showed an overestimation of the E-Field in the majority of the works selected for this study. It also identified some wrong assumptions regarding the physics underlying the calculation of the E-Field in the culture medium. Based on these findings we provide some general advice for future aplications of capacitive coupled E-Field stimulation in TE.
In the three studies where there was a good agreement between the reported values and our theoretical estimates, we found that the electrical response of the setup was modelled correctly. Brighton et al. 15 do not provide detailed information regarding the methods used to estimate the E-Field in the culture medium. However, in 34 they stated in a footnote that "The E-Field and the current density were calculated on a macroscopic continuum basis by solving the boundary value problem constructed from Maxwell's electromagnetic field equations. Comparable solutions were obtained using a two-dimensional closed-form solution technique and a three-dimensional computer-generated solution using finite element analysis". This approach is similar to ours, which, together with reasonable estimates of the missing physical parameters, predicted almost the same value for the E-Field as reported in the paper. Hartig et al. 17 based their E-Field estimates on an electric circuit described in 8 and that is essentially the same as the one shown in Fig. 1 of this paper. Unfortunately, the values of the resistances and capacitances were not specified, nor was the duration of the rising edge of the saw-tooth voltage waveform. In addition, a potential difference across a cellular monolayer was reported, not the E-field in the culture medium. Despite these unknowns, the agreement between the reported value and our calculations was good. In Stephan et al. 19 the E-Field was computed using the electric currents interface of the COMSOL FE software, based on the quasi-electrostatic approximation of Maxwell's equations. This FE approach is the same as ours and despite the uncertainty due to the absence of the exact petri dish wall thickness, a good agreement was found with a typical value for this missing parameter.
Fitzsimmons et al. 6 used an appropriate simplified electrical circuit to model the electrical response of the setup, but the resistance of the culture medium was likely overestimated, leading to an overestimate of the E-Field.
In the studies by Rodan et al. 7 , Korenstein et al. 12 , Griffin et al. 18 and Khaw et al. 21 the approach followed to estimate the E-Field was inappropriate because it did not consider the conductive nature of the culture medium Table 2. Values of the resistances, capacitances, reactances and frequencies for the three-layer analogue circuit models of the CCoupled setups. **Matched frequency.  www.nature.com/scientificreports/ or the temporal variation of the applied voltage. In CCoupled setups electric charge on the electrodes creates an E-Field in the culture medium which leads to the accumulation of charge of the opposite sign at the interface between the (conductive) culture medium and the insulator. This secondary charge distribution creates an E-Field that points in the opposite direction to the E-Field created by the charge on the electrodes and is such that, for a constant applied voltage (DC), the total E-Field in the culture medium would be zero. In Rodan et al. 7 , the reported value of 1.166 ×10 5 V m −1 was obtained by dividing the applied voltage (1750 V) by the distance between electrodes (15 mm) but this is physically incorrect given that the materials between the electrodes have very different conductivities and permittivities. In Korenstein et al. 12 , the resistive impedance of the culture medium is considerably lower than its capacitive reactance (Table 2), despite the high frequencies involved. It is therefore its resistive impedance that will determine the potential drop and hence the E-Field in the culture medium, thereby invalidating the assumption on which the calculations were based. In Griffin et al. 18 the low resistive impedance of the culture medium is also ignored, resulting in an overestimation of the E-Field by eight orders of magnitude. In Khaw et al. 21 the choice of the electrostatic interface for the FE analysis, which cannot take into account currents in conducting media, is the reason why a non-zero E-field was wrongly predicted.
The analysis of these eight studies, highlights the importance of accurate and detailed reporting of the physical parameters of the setup (dimensions, electrical properties) and the voltage waveform (particularly, risetimes of sharp edges) to enable replication of the electrical stimulation. When this information is available, a number of numerical approaches can produce sufficiently accurate estimates of the E-Field in the culture medium. The resulting computational model of the setup constitutes its digital twin, which has several useful characteristics. It can be shared, and it can be used to investigate the effect of changes in the setup parameters and voltage waveform on the E-Field in the culture medium. It can also be used to determine the changes in the setup required to achieve the desired E-Field. CAD files are a practical way of documenting and sharing the geometry of the setup.
Regarding the choice of the numerical approach, an analytical solution based on the simple series C-R-C circuit shown in Fig.1d should provide a useful first estimate of the E-Field in most cases. This approach can be extended to non-sinusoidal waveforms by estimating the frequency associated with the fastest rising or falling edges of the applied voltage. Alternatively, a circuit simulator like LTspice can provide a graphical illustration of the temporal variation of the E-Field in the culture medium for arbitrary waveforms. Note, however, that a single frequency must still be chosen to calculate the capacitance of the insulating layers. Also, a very good approximation to the temporal variation of the E-Field can also be obtained by simply plotting the first derivative of the voltage waveform with respect to time (Eq. 13).
If the geometry of the setup differs significantly from the ideal coaxial geometry of constant section that is assumed in the analytical solution, then the FE method may be used to take into account the complexity of the geometry. However, even in the case of the geometry implemented in Rodan et al. 7 and shown in Fig. 5a, it was possible to estimate the E-field using a simple cylindrical (coaxial) model (Fig. 5b) and still obtain almost identical values for the E-Field (Table 4). Another advantage of the FE method is that it makes no assumptions about the frequency spectrum of the applied voltage, which is not the case for the analytical and circuit simulator approaches. Nonetheless, our predictions of the E-Field for the eight studies analysed (Tables 3 and 4) are practically the same for all three independent approaches (less than 3% deviation from the mean value of the three prediction methods).
The E-Field values reported in the selected studies ranged from 1.0×10 −5 V m −1 to 1.0×10 5 V m −1 . According to our calculations the actual range of applied fields was 1.0×10 −8 V m −1 to 1.0×10 2 V m −1 , still a range of 10 Table 3. List of studies where an agreement was observed between the reported and predicted magnitude of the E-Field in the culture medium. www.nature.com/scientificreports/ orders of magnitude. This is explained in part by the wide range of frequencies used, from Hz to MHz, and the fact that E-Field strength is proportional to frequency in the setups described.
The effect of electrical stimulation on cell response is likely to be frequency dependent. For example, Brighton et al. 15 failed to reproduce the effects on cell proliferation reported in Fitzsimmons et al. 6 at 10 Hz and an E-Field strength of 1.0×10 −5 V m −1 (and note that Fitzsimmons probably applied a field some 30 times weaker). On the other hand, Krueger et al. 36 have recently reported an effect on chondrocytic differentiation capacity with fields of 5.2×10 −6 V m −1 and 5.2×10 −5 V m −1 at a frequency of 1 kHz. Thus, optimization of CCoupled electrical stimulation protocols should consider E-Field strength and frequency as independent parameters.
Overall, the results presented in Tables 3 and 4 show that the analytical and circuit simulator approaches outlined previously may give an estimate of the E-Field intensity with sufficient accuracy for most purposes. In this work we have assumed a homogeneous culture medium. The presence of a scaffold can introduce local variations of the E-Field (hotspots, coldspots) that may introduce localized effects on the cell culture 22 . In this case, the FE method should be applied to take into consideration the complex geometry of the scaffold.
In this study we analyzed the E-Field in eight CCoupled setups that were used in twenty studies, published between 1978 and 2021. The E-Field was correctly estimated in only 3 out of 8 setups and 8 out of 20 studies. We limited our analysis to bone and osteogenesis related studies but similar trends will probably be found in applications involving other tissues. Of course, the methods outlined here can used to predict the E-Field in CCoupled setups for electric stimulation of cell cultures of any type.
Based on the analytical approach presented in this work, we have developed an E-Field Calculator for CCoupled Systems with a layered cylindrical geometry. This calculator is free, open-source and is publicly available Table 4. List of studies where a disagreement was observed between the reported and predicted magnitude of the E-Field in the culture medium. . More details about the E-Field calculator and its operation are available in the supplementary materials. Even though the laws of physics enable a reasonably accurate prediction of the E-field in the culture medium, the model should still be validated experimentally. Ideally, the E-field strength in the culture medium should be measured, but it may be difficult to do it correctly and accurately in most setups. Alternatively, the applied voltage and the current through the setup should be measured and reported. The ratio of these two quantities gives the total impedance of the setup, which can be compared with the value predicted by the model.

Conclusion
This work has shown a predominant overestimation of the E-Field applied in capacitively coupled ES studies. Furthermore, the reported E-Fields were calculated and not measured at any stage of the experimental protocol. Errors in E-Field calculation may have lead to wrong conclusions regarding the influence of the E-Field on cell homeostasis, growth and differentiation. In future CCoupled studies, the setup for electric stimulation should be designed based on a numerical approach, such as the ones outlined in this paper, to estimate the E-Field in the culture medium previous to the construction of the experimental setup. This digital twin should contain all the information necessary to reproduce the experimental setup and should be made available on publication of the study. In addition, the predictions from the model should be validated to the largest possible extent, to confirm the E-Field characteristics that originated the cellular effects observed. These improvements would be crucial steps towards understanding how CCoupled stimulation modulates cellular behaviour, allowing to further optimize stimulation protocols for an effective translation of this technique to the clinical context.