Experimental study on ultrasonic irradiation for enhancing coalbed methane recovery

The present study proposes the use of a new ultrasonic irradiation method to enhance permeability and desorption for gas recovery from low-permeability coal reservoirs. A triaxial stress ultrasonic irradiation test apparatus was developed specifically for coal, considering the properties of gas adsorption, migration, and sound intensity, and providing a simultaneous measurement of gas flux, to investigated the deformation and temperature of coal samples obtained from the Fuxin coal field by permeability and desorption experiments. With the ultrasonic irradiation duration, the permeability of coal improved gradually with unequal variation, accompanied by the Klinkenberg effect where it decreased rapidly and then increased slowly with increasing gas pressure. The ability to desorb coal was enhanced by higher sound intensity ultrasound irradiation, and the volume of gas desorption was much greater than that of the sample without mange, the temperature and strain were demonstrated as a “J shaped” curve. An X-ray computer tomography (CT) technique was used to visualise the meso- or macro-cracks in the coal sample at pre- and post- ultrasonic irradiation, consequently, fractures expanded under the irradiation of ultrasonic waves. A permeability and desorption model was developed to describe the improvement of coal seam gas production capacity under ultrasonic irradiation, which introduced effective sound pressure.

www.nature.com/scientificreports/ in non-uniform deformation during ultrasonic irradiation, which promotes crack propagation in rocks and increases fluid migration space 31 , accelerating gas desorption on the surface of the coal matrix 32,33 . Therefore, ultrasonic irradiation can be used as a new method to improve the gas permeability of coal and promote the gas seepage capacity, for underground gas in-situ extraction after roadway excavation.
In the present study, further investigations into the permeability of coal samples with ultrasonic irradiation and gas flux tests were conducted using a triaxial stress test apparatus at different confining and gas pressures. The simultaneous strain and temperature were also measured. The internal fractures in coal before and after ultrasonic irradiation were observed by computer tomography (CT). Mechanical models were then developed to describe the permeability and desorption of reservoirs under the influence of the sound intensity. Based on this, coal source exploitation can eliminate gas anomaly accumulation and improve the efficiency of coalbed methane reservoirs, which reduces greenhouse gas emissions and contributes to more natural gas production.

Experiments
Sample preparation. The bottle coal bulks were collected from the Wulong Colliery to a depth of 950 m and immediately sealed with valve bags. The study area is located in the middle of Fuxin Coalfield, Liaoning Province, China, which is one of the most successful areas for the commercial development of coalbed methane in China. The coal reservoir gas content was 11,167 m 3 /t, with an average porosity of 4.7% and average density of 1189 kg/m 3 . Cylindrical specimens measuring ϕ 50 mm × 100 mm were prepared in the laboratory, in which the coring direction was perpendicular to that of bedding development, and to weaken the influence induced by the difference between the two ends, both ends of each specimen were polished to ensure that the flatness error was less than ± 0.02 mm, using a drill bit to obtain a hole with 8 mm diameter and 50 mm depth at the centre of the sample end to place the thermocouple, as shown in Fig. 1a and b. Table 1 summarises the physicochemical composition of the coal. X-ray diffraction (XRD) showed that more minerals were observed, mainly quartz and clay, pyrite, and calcite, as secondary compositions in the coal. The aim of this study was to investigate whether ultrasonic stimulation increases permeability; therefore, the effect of clay swelling on the strain of coal under water-saturated conditions is negligible.  www.nature.com/scientificreports/ Experimental setup. A triaxial ultrasonic irradiating test apparatus was developed specifically for stressed coal, taking the properties of gas adsorption, migration, and sound intensity into consideration under stress conditions and providing a simultaneous measurement of gas flux. The test system includes five parts, as shown in Fig. 2: (1) A pressure chamber applies hydrostatic pressure to the coal sample Steel pressure vessel was cut from manganese steel and dimensions was height 300 mm, outer diameter 200 mm, inner diameter 150 mm, with a safety design pressure resistance of 50 MPa. A hydrostatic loading apparatus was used to pump in fluid medium to the axial and circumferential directions to bring the coal sample to hydrostatic pressure and the power source was a hydraulic pump by using water, which has a pressure transmission capacity of 40 MPa, digital gauges recorded the pressure (full scale 25 MPa, with a resolution of the number of impressions at 5‰), and a capsule accumulator stabilised the pressure in the system. The device has good sealing and experimental accuracy in the temperature range of 10-50 °C.
(2) A gas monitoring system applied gas adsorption and directional flow while recording gas migration.
As nitrogen and methane have similar properties in coal adsorption and migration 34 , a stable pure nitrogen gas source with purities of 99.999% is used for seepage and adsorption in the coal for safety during testing. An air regulator, a high-accuracy digital gauge (full scale 25 MPa, with a precision of 0.05%), and an air valve are connected sequentially by a stainless-steel pipeline, then to a gas channel on the pressure cell. Gas seepage through the coal occurs via a stainless-steel pipeline and enters a six-way valve, which is connected to a gas flowmeter to monitor the gas pressure, and the flux data are recorded per second and resolution is 0.001 m/s. The other method includes a connection to a vacuum pump to remove gas impurities from the coal samples before the trials.
(3) A strain monitoring system detected and recorded axial and circumferential strains.
The axial and circumferential deformations of the sample were measured by two BX120-15AA resistance strain gauges that were perpendicular to each other and attached to the surface of the sample, which test accuracy of strain is 10 −6 , the digital signals of the axial and circumferential strains were collected using a DHC 5995 h dynamic strain indicator for real-time observations, manufactured by Donghua Technology, Ltd., display, and recorded by a high-speed computer. The average tolerance of the strain gauge was 0.1%, and the sensitivity coefficient was 1%. The sampling frequency was set to 0.1 Hz.
(4) A temperature monitoring system recorded the temperature variation of the coal sample.  www.nature.com/scientificreports/ A thermocouple was fixed on the lower gripper, the heat sensitive part probed the hole in the sample (measuring range − 20 to 130 °C, thermal response time is 0.01 s, and error is 0.005 °C), as shown in Fig. 1b, and the wire external temperature display module recorded every 30 s.
(5) An ultrasonic generating system applied ultrasonic irradiation with different sound intensities to the sample. The ultrasonic generating system contained an ultrasonic generator and an ultrasonic irradiation probe. The ultrasonic irradiation probe was fixed on the upper gripper, and a high-strength steel disc was placed between it and the specimen to prevent local stress concentration on the surface of the sample. The ultrasonic generator provides three sound intensities to the probe, according to Eq. (1) and listed in Table 2, which can be shifted by a gear as needed. The system has a fixed ultrasonic frequency, in the paper is 30 kHz, and the sound intensity of ultrasonic does not change with frequency, so it was not included in present study. In addition, the sound intensities were determined according to the basic performance parameters, the equipment we used had 3 current gears for selection.
Experimental program and procedure. The experiment involved gas adsorption and flux testing of coal samples at different confining and gas pressures, ultrasonic sound intensities, and irradiation durations; the confining and gas pressures and the sound intensity gear positions are shown in Table 3. The experiment in the present study consists of two parts: one constitutes permeability measurement, as shown in Table 3 test types I and II, the other constitutes desorption measurement as shown in Table 3 test type III. The following procedure was conducted: (1) Sample pretreatment and installation: Strain gauges of electrical resistance were mutually perpendicular to each other and placed on the surface of the coal. The thermocouple was fixed on the lower sample holder and in close contact with the upper and lower holder with a thermoplastic sleeve covered on the surface to separate the confining pressure from the pore and placed in the pressure cell. The ultrasonic irradiation probe was placed on the top of the steel pressure vessel and connected to all instruments and sensors. (2) Pressure was applied, and gas adsorption occurred. First, the steel pressure vessel was filled with water with alternating axial loads equal to the confining pressures of the hydrostatic pressure state as predetermined (σ 1 = σ 3 = 4, 8, and 12 MPa). After closing the inlet switch and opening the six-way valve connected to the vacuum pump, the coal sample was placed under a vacuum for 8 h to extract the impure gases. Subsequently, the inlet switch was opened, the six-way valve was closed, and the gas flowed into the coal sample to a predetermined pressure (P a = 1.0 MPa) and was adsorbed for 24 h to saturation.   www.nature.com/scientificreports/ temperature. After different ultrasonic irradiation durations (t = 2, 4, and 12), the inlet opening switch and the six-way valve were turned to the flowmeter, the gas pressure (P a = 0.2, 0.5, 0.8, 1.0, 1.2, and 1.5 MPa) was gradually adjusted, and the gas pressure and flux data were recorded. (4) Desorption: The sample was kept under hydrostatic pressure, the inlet switch was closed, and the six-way valve was opened to the air until the free gas in the coal was discharged and then entered the flowmeter. Simultaneously, the irradiating gear of the ultrasonic generator increased to the predetermined values, or no irradiation, recording the deformation of coal and the temperature, and obtaining gas desorption by drainage gas collection. (5) The tests were repeated by changing the confining pressure, gas pressure, and sound intensity according to the testing scheme. Procedures (1), (2), and (3) were repeated after replacing the coal sample for permeability measurement, and procedures (1), (2), and (4) were repeated after replacing the coal sample for desorption measurement.
It is worth noting that all experiments were conducted in the laboratory at room temperature (20 °C), which was maintained at a constant by air conditioning. In addition, the internal pore structure of the coal before and after ultrasonic irradiation was observed using CT. We assume that gas permeation through specimens is an isothermal process, and that coal can be regarded as an isotropic homogeneous material. Therefore, the gas permeability can be expressed by Darcy's law: where k is the permeability (mD); Q is the velocity of the gas flow (cm 3 /s); A is the average cross-sectional area of the specimen (cm 2 ); L is the length of the specimen (mm); Pa is the inlet gas pressure (MPa); Pb is the outlet gas pressure (MPa); and μ is the gas viscosity (Pa s, μ (N 2 ) = 10.093 Pa s).
As shown in Fig. 3, there are similar trends of permeability for coal samples under different hydrostatic pressures; permeability decreases rapidly at first and then increases slightly, displaying "V shaped" variation characteristics with increasing gas pressure. The main reason for this phenomenon is the Klinkenberg effect in coal, under low gas pressure, the coal acts as a type of porous medium, and there is no significant difference in the velocity of gas molecules between the centre of the channel and the wall, furthermore, the mean free path of the gas molecules reaches the sides of the channel, and the diffusion of gas molecules freely occurs without collision, resulting in considerable initial permeability. However, this effect faded as the gas pressure increased, and the permeability gradually declined, even under ultrasonic irradiation. As the ultrasonic irradiation duration increased, the permeability of coal gradually improved at each gas pressure with unequal variation. By conducting quotients on the change and initial permeability, the quantitative results of the permeability growth rate were obtained and are listed in Table 4. This clearly indicates that the growth rate increases with increasing irradiation duration; for example, the growth rates of sample # 1 were 22.4%, 44.25%, and 110.34% after 4, 8, and 12 h of irradiation, respectively. However, it also demonstrated that the growth rate of permeability decreases with improving gas pressure and higher hydrostatic pressure; for example, the growth rates of sample # 3 were 23.48%, 19.58%, 13.92%, 13.89%, 11.26%, and 15.94% after 12 h of irradiation with increasing gas pressure, respectively. For samples # 1, # 2, and # 3, the growth rates were 71.8-110.34%, 50.00-94.27%, and 23.94-48.48% after 12 h of irradiation with increasing gas pressure, respectively. It means that, ultrasonic irradiation did improved the permeability of coal, for the mechanical effect periodic of loading and unloading during ultrasonic transmission, cracks were formed between coal particles, which has been confirmed by research 35 , provided much new effective channels for gas migration and the longer irradiating duration, the better cracks formation in coal. However, the promotion slows down with the inhibition of external confining pressure, for the increase of critical crack growth stress. In general, the impact of a longer irradiation duration is quite beneficial for increasing the permeability of the coal reservoir, however, it generated much small fractures and cannot change the fundamental seepage law of the reservoir, which is related to the Klinkenberg effect, and the higher hydrostatic pressure inhibiting it. In this part, the variation of permeability with gas pressure under ultrasonic irradiation can be expressed as: where a, b, c, are the fitting parameters (mD, mD/MPa, mD/MPa 2 ,) and related to the ultrasonic duration.
The temperature was recorded by the thermocouple and is expressed as an "S shaped" curve and dived into 4 stages, as demonstrated in Fig. 4: (1) initial temperature stabilisation, (2) stable warming, (3) slow warming, and (4) constant temperature phase during the 12 h of irradiation. In the initial temperature stabilisation phase (1), the curve was approximately a straight line where the temperature recorded only a slight rise at 17.1-17.3 °C. In the stable warming phase (2), the temperature increased with a relatively stable growth rate. The slow warming phase (3), wherein the curve improved with a gradually diminishing growth rate, trended to 0, and was concave    There are two effects in coal with ultrasonic irradiating, which the fatigue effect and thermal effect, former is dissipated as crushing energy to promotes cracks development, and the latter is converted into heat to increase the temperature of the coal. When the input energy caused by ultrasonic irradiating was constant in unit time, according to the previous results that the permeability increment was small at high stress, it means more energy was converted into heat and less to dissipation as cracks development. As a result, the samples with a higher stress state shown a shorter warming duration lasted and faster the temperature rose. The axial, circumferential, and volumetric strains are shown in Fig. 5, and all the values were positive, which implies that the entire behaviour of coal under irradiation exhibited swelling deformation. A similar variation was seen based on the volumetric strain, in general. The micro-expansion phase (a) of the samples has a smaller value and growth rate in the first few hours, and the duration is gradually prolonged by the effect of the hydrostatic pressure increase. The measurements of samples # 1, # 2, and # 3 were 1.4, 2.5, and 4.8 h, respectively. Thereafter, the slope of the strain curve increased, and the total strain gradually recovered with little fluctuation to enter the stable macro-expansion stage (b) represented by the dotted red line, where a smaller strain growth rate takes shape with a larger hydrostatic pressure. As a result, the volumetric strain of sample # 3 was 0.00982, and that of sample # 1 was 0.01324. In addition, it is clearly seen that the axial strain was always shorter than that formed by the circumferential strain in all experiments, and the latter entered the stable macro-expansion stage before the former. On the one hand, for the reasons of this phenomenon, numbers of cracks emerged and opened in coal for the fatigue effect of ultrasonic irradiating, and then expansion deformation was caused, the relationship between cracks and deformation was confirmed by the article 8 . On the other hand, it was easy to found that, the deformation formed lag behind the change of temperature, compared with the results in the previous, with the increased of temperature, the thermal expansion of a large number of matrix particles forms macro deformation www.nature.com/scientificreports/ was monitored. However, the higher the pressure, the greater the inhibition of deformation, as well as the coal at low confining pressure, the faster the deformation speed, the greater the deformation. Figures 6 and 7, in combination with Figs. 4a and 5a, demonstrate that when the permeability and strain of samples were under a hydrostatic pressure of 4 MPa at different ultrasonic irradiation gear positions, the sound intensities were 41.45, 58.04 and 60.80 W cm −2 for samples # 1, # 5 and # 6, respectively.
The evolution of permeability with gas pressure still conformed to the seepage law influenced by the Klinkenberg effect, except that the spacing between curves of different irradiation durations increased with a higher sound intensity and enabled coal to pass gas more easily. As shown in Table 5, the growth rate increased with higher sound intensity, with that of samples # 1, # 4, and # 6 being 71.81-110.34%, 106-136.09%, and 105.81-133.85%, respectively, after 12 h of irradiation.
As presented in Fig. 7, the performance curve was "S shaped", with 4 stages. For the irradiation performed with an increasing sound intensity, the sample curves were observed with a larger growth rate in the stable warming process, shorter slow warming phase, and higher temperature continued. The observed temperatures for samples # 1, # 5, and # 6 were 22.97 °C, 22.73 °C, and 22.35 °C, respectively. Thus, we can see that under the irradiation at higher sound intensity, it is easier for the sample to reach a higher equilibrium temperature in a short time.  www.nature.com/scientificreports/ As shown in Fig. 8, the strain of the samples can be divided into 2 phases: micro-expansion and stable macroexpansion. The former was gradually shortened as the sound intensity improved, and the growth rate of the latter increased. For samples # 4 and # 5, the first phase lasted 1.3 h and 0.8 h, respectively. In addition, the sample with a higher sound intensity showed a larger strain growth rate and developed more overall strain, especially in the circumferential direction.
It can be found that, for the two effects of ultrasonic irradiation improved as the effective sound pressure increased, where the permeability, temperature and strain turn faster and larger, for there was much more ultrasonic energy is converted into heat through the friction between the particles, the interface, and the absorption of the medium. And the grater mechanical vibration accompanied by the relative displacement of the matrix and mutual friction. It is worth noting that the mechanical effect is the main mechanism of material fracture, by which tensile stress is generated by transverse waves and shear stress is generated by longitudinal waves between the matrix, where the cracks of types I and II are initiated and developed 36 . In the present experiments, when the effective sound pressure was constant, at a certain value of the total energy input, for samples with a higher pressure state, a larger fracture toughness, and increased critical expansion stress, few cracks developed, surface energy dissipated, and most of the energy was converted to heat, resulting in a larger rate of temperature increase  www.nature.com/scientificreports/ and lower recorded strain; when the heat transfer from the coal to the outside was the same as the energy generated by the ultrasonic wave, the temperature tended to be a fixed value. Conversely, a higher sound intensity irradiation had more energy input into the coal, and a larger stress formed between the matrix; thus, a larger growth rate and higher equilibrium of temperature and strain were recorded. As shown in Fig. 9, the gas desorption volume increased rapidly at first, and as time progressed, the slope of the curves decreased gradually, resulting in a lower desorption rate. The total desorption volume decreased to an approximate stable value, and the major desorption of the samples used in the present study was concentrated in the first 8000 s, more than 95% of the total. It can be seen that the desorption volume of the irradiated sample was greater than that of the sample without irradiation, and it increased with higher sound intensity. This demonstrates that the ability to gas desorb from coal is enhanced by ultrasound irradiation. More adsorbed gas molecules deviate from the surface of the coal matrix and move to the lower gas pressure in the free state, through the pores and fissures inside the coal, displaying a higher rate of desorption and greater total volume for the macro phase. Figure 10 shows the temperature of the samples with and without irradiation. It is noteworthy that, the temperature of the sample without irradiation recorded during the gas desorption is shown as a "V shape" that decreases after the subsequent increase in the range of 0.1 °C, and the inflexion point is approximately 7000-9000 s. The other results were "J shaped" curves, in which the growth gradient increased gradually, and the www.nature.com/scientificreports/ temperature gradient and the final were improved with a larger sound intensity. The process of gas sorption and desorption from the coal matrix is accompanied by temperature fluctuations, which has been confirmed in many studies 37,38 and is caused by the release and absorption of energy. More energy was transformed from coal into gas due to its initial free energy with a larger desorption rate, then, the recorded temperature decreased and was lower than normal. As resolution gradually decreased, less energy was needed, the outsider energy transformed into samples, and the temperature of the sample rose and drew towards normal. In contrast, the ultrasonic thermal effect provides more energy for the adsorbed gas molecules to move freely and desorb from the coal matrix, more free gas transport into the outer free space. Moreover, ultrasonic irradiation causes significant thermal effects in coal and increases with longer duration and higher sound intensity, and the recorded temperature curve in coal has smaller growth gradients in the early stages and higher growth gradients in the later stages, when the gas desorption endotherm is considered. Furthermore, there was much small cracks emerged, result in the fatigue effect caused by a high number of periodic irradiation, which provided storage space and migration channel for gas desorption to free, and it had more gas desorption amount per unit time and total amount. The strain of the samples can be seen in Fig. 11, which shows a similar pattern of axial and circumferential strain variation; the strain variation of sample # 7 without irradiation had an obvious negative value and shrinkage with gas desorption from the coal, which showed a larger shrinkage rate in the first 6000-8000 s and gradually slowed down in the latter stage. In contrast, the strains of the samples with irradiation all were positive and expanded over the entire process, where a smaller growth rate initially and slowly increased, and then, the strain presented a steady expansion after 6000 s. The strain of the samples increased with sound intensity, both axially and circumferentially, and the circumferential strain was much greater than the axial strain, as that shown before on gas seepage. With ultrasonic irradiation, in general, the strain of coal with gas desorption is lower than that of samples with gas-saturated adsorption. www.nature.com/scientificreports/ Due to the occurrence of the phenomenon during gas desorption in this part, the matrix shrinkage of coal is accompanied by gas desorbed from the surface of the coal matrix 39 , especially at the initial rapid desorption stage, where the negative strain of shrinkage characteristics came into being. A small decrease in temperature with gas desorption was recorded at present, which produced more shrinkage. On the one hand, the thermal effect gradually increased with the positive strain during the ultrasonic irradiation of the sample, as we concluded before in this paper, and it also inhibited gas desorption, while on the other, the fracture was caused by mechanical effects, in which more strain and cracks were created for the free gas swarm and migration, promoting the dynamic balance of desorption to the positive development. During the gas desorption of coal with ultrasonic irradiation, coupling not only shrinks but also swells. The strain is the comprehensive result of the shrinkage and swelling effect in the macro scale. As a result, in the first period with a high desorption rate, the axial and circumferential strain experienced little increase, and it will take longer with a lower sound intensity irradiation; in the second period with a low desorption rate, the strain variation increased as the growth rate continued to rise. For a larger temperature growth rate caused by a higher sound intensity, it is easier to reach a higher temperature of the sample with shorter irradiation duration, larger strain emerged at the same time, and eventually more gas was collected.

Discussion of the mechanism promoting the permeability and desorption enhancement by ultrasonic irradiation
To further verify the fundamental mechanism promoting the permeability and desorption of gassy coal using ultrasonic irradiation, the cleat properties of the samples before and after ultrasonic irradiation were scanned by CT analysis. The CT scans were performed using a 225-kV FCB μCT scanner (Institute of Applied Electronics, CAEP) with a magnification of 1 × to 400 ×. We selected a diameter of 50 mm for each coal sample section, where six layers were divided along the axial direction, as shown in Fig. 1c, and the resolution under the operational conditions stated here was approximately 250 × 250 μm 2 . A list of CT images of the samples is presented in Fig. 12.
For the result presented in Fig. 12, significant changes have occurred in these areas before and after irradiation, as marked with red and named "a" and "b". With the increase in the area or length of the black, the fractures had expanded under the irradiation of ultrasonic waves, which is the result of the dynamic evolution of cracks from meso to macro caused by the stress concentration formed at the original damage, as confirmed by the Griffith strength criterion and damage mechanics. This damage provides much temporary storage spaces after gas desorption, and more effective penetration channels for gas migration, the gas has a higher flow rate at the same pressure gradient. Moreover, with an increase and communicate of the voids in coal, there is a smaller gas pressure during desorption, and more adsorptive gas is transformed into a free state and migrates into the open areas. In general, the higher sound intensity caused the grate-irradiating force on the sample, and a larger channel formed for gas migration, which is beneficial for gas recovery in coalbeds.
The relationship between the permeability of coal under ultrasound irradiation and gas pressure can be expressed in the form of Eq. (4) combined with Eq. (3), where a 1 , b 1 , c 1 , a 2 , b 2 , and c 2 are the fitting parameters (mD, mD/MPa, mD/MPa 2 , mD W/cm −2 , mD W/cm −2 MPa −1 , and mD W/cm −2 MPa −2 ); k 0 is the absolute permeability without ultrasound, and the second is the permeability increment caused by the intensity of the ultrasound, both of which are associated with gas pressure. Further simplified, the permeability of coal with ultrasound irradiation can be expressed by Eq. (4). This demonstrates that, in the range of ultrasonic influence, the increase in coal sample permeability is mainly caused by ultrasonic sound intensity and extra increment, the gas permeability rate increases significantly with the increase in pore pressure 40 , and also with a longer irradiation duration with more energy input. As the measurement result in the present paper shows in Figs. 3 and 6, with a higher sound intensity and longer irradiation duration, the permeability of the samples increased, and the corresponding fitting parameters improved. Thus, the ultrasonic waves have a significant effect on improving the permeability in low coal reservoirs.
In previous studies 41 , the relationship between the gas desorption volume (Q t ) and time was similar to the Langmuir adsorption curve, as shown in Eq. (5), where d is the saturated desorption and e is the parameter (mL and s −1 ). For the desorption of coal under ultrasound irradiation, the saturated desorption can be defined as the product of the proportional coefficient (A), mL cm 2 /W, and the effective sound intensity (J 0 ). Then, the relationship between volume and duration can be expressed in the form of Eq. (7). This demonstrates that, with a higher sound intensity irradiation, the kinetic energy of the gas is increased, and the gas adsorbed internally and on the surface are more easily desorbed and freed. In addition, as the irradiation duration increases, more cracks emerge in the coal for transport, and more gas is collected.

Conclusion
In this study, a triaxial stress ultrasonic irradiating test apparatus was developed specifically for coal, considering the properties of gas adsorption, migration, and sound intensity, providing simultaneous gas flux measurements, and enhancing the permeability and desorption for gas recovery from a coal reservoir. The entire deformation and temperature of the coal samples obtained from a depth of 950 m in an underground mine with high gas pressure and content were investigated by permeability and desorption experiments with or without ultrasonic irradiation. The former included three levels of confining pressure, six gas pressure, three irradiation durations and three sound intensities. The variation in the internal structure before and after irradiation was observed using CT scanning. Based on the findings of this study, we draw the following conclusions: 1. With ultrasonic irradiation, the gas permeability of coal is still accompanied by the obvious Klinkenberg effect, as the ultrasonic irradiation duration increases, the permeability of coal improves gradually at each gas www.nature.com/scientificreports/ pressure with unequal variation. The growth rate of permeability increases with longer irradiation and larger sound intensity but decreases with higher gas and hydrostatic pressure. The variation of temperature was "S shaped" with four stages, with the increase in sound intensity and hydrostatic pressure, which had a higher stable value and greater growth gradient, result in the difference of fracture toughness under hydrostatic stress conditions. Moreover, the strain evolution also developed with a growth rate and final value, which were shown as two phases of micro-and macro-expansion. 2. The desorption of coal is enhanced by the cracks development due to mechanical effect, and thermal effect provided additional energy to increase molecular kinetic energy thermal of ultrasound irradiation, the volume of gas desorption was much greater than that of the sample without mange, and it increased with the sound intensity. The changes in temperature and strain simultaneously displayed a "J shaped" change that increased rapidly following an initial slow increase, which was affected by the gas desorption attracting volumetric shrinkage and temperature reduction. 3. CT scans demonstrated that the fractures had expanded under the irradiation of ultrasonic waves, the resulting dynamic evolution of cracks from meso to macro caused by the stress concentration formed at the original damage, which provides the channel for gas desorption and migration under a pressure gradient. A model of permeability and desorption developed to describe the improvement of coal seam gas production capacity, which introduced effective sound pressure and described the enhancement mechanism of ultrasonic irradiation. Further studies should focus on investigating the influence of the quantified ultrasonic intensity and excitation frequency on the permeability of coal and its engineering applications.
Ethical statement. I certify that this manuscript is original and has not been published and will not be submitted elsewhere for publication. And the study is not split up into several parts to increase the quantity of submissions and submitted to various journals or to one journal over time. No data have been fabricated or manipulated (including images) to support your conclusions. No data, text, or theories by others are presented as if they were our own. The submission has been received explicitly from all co-authors. And authors whose names appear on the submission have contributed sufficiently to the scientific work and therefore share collective responsibility and accountability for the results.