Structural rationalities of tapered hollow cylindrical beams and their use in Japanese traditional bamboo fishing rods

Bamboo has historically been used in Japan as a structural material and for building tools such as fishing rods owing to its remarkable structural properties. In recent years, the materials used for manufacturing fishing rods have changed greatly owing to the development of composite materials; however, the basic slender tapered hollow cylindrical fishing rod design has remained unchanged throughout the long history of fishing. However, the mechanical rationale behind this structural design has not yet been sufficiently verified, and this study clarifies this. The analysis was performed by solving the nonlinear bending equation of a slender tapered cantilever beam with a concentrated load at the tip, which causes large deflection, using the Runge–Kutta method. The deflection curves and bending stresses were obtained, and the structural design to minimize the stresses was explored. Our results may prove useful for bamboo-inspired bionic design and bring to light our ancestors’ deep knowledge of natural materials and their advanced technological capabilities.


Results
Derivation of basic equations. In this study, a slender tapered rod of length l is considered as a cantilever beam with a fixed end at the large end, as shown in Fig. 2a. The intersection point of the neutral axis and fixed end is designated the origin; the fixed end of the neutral axis is defined at s = 0 and the free end at s = l . The free end is subject to a concentrated load P in the horizontal direction, and the member is assumed to be an isotropic elastic body with a constant longitudinal modulus of elasticity E . The cross-sectional forces acting on an arbitrary cross-section are the axial force T (positive for tension), shear force F , and bending moment M (Fig. 2b).
The cross-sectional diameters of the rod at the fixed and free ends are D 1 and D 2 , respectively. D 1 is assumed to be proportional to D 2 , and the proportionality constant is called the taper ratio, denoted by ξ ( = D 2 /D 1 ). In this study, the diameter D(s) of the model is expressed by Eq. (1).
The cross-sectional area A(s) and cross-sectional second moment I(s) are functions of s , and the diameter varies as a linear function of s . The following Eqs. (2) and (3) are obtained.
The volume V 12 of the slender tapered rod can be expressed by Eq. (4). Therefore, if this tapered rod is converted into an untapered rod under the same volume and height conditions, its diameter D o can be expressed by Eq. (5) using D 1 . Photographs of kisyuu-herazao, a type of Japanese bamboo rod, which has a history exceeding 100 years and is designated as one of Japan's traditional crafts (Courtesy of Hashimoto-City, Wakayama, Japan), (c) Bamboo grove of species Sasamorpha borealis, which is used to make the kisyuu-herazao because of its hardness and rigidity (Courtesy of Hashimoto-City, Wakayama, Japan). The theoretical analysis is conducted in the elastic region and the members are assumed to be inextensible; thus, the Euler-Bernoulli assumption is valid. The effects of shear force and the Poisson effect are neglected. The basic equation for bending is given by Eq. (6). Differentiating Eq. (6) with respect to s , we obtain Eq. (7).
The ratio s/l is defined as η . Furthermore, if the cross-sectional second moment of the untapered rod is I o and the dimensionless load is α o = Pl 2 /EI o , the second-order nonlinear differential equation can be obtained as shown in Eq. (8). In this study, the deflection due to the weight of the rod is assumed to be smaller than that due to the concentrated load P , and the effect of its own weight is ignored. Equation (8) was solved by direct numerical analysis using the Runge-Kutta method. From the analysis, the deflection angle θ(η) and curvature dθ(η)/dη at point η were determined, and the large deflection curve and bending stress were derived as described below. The coordinates x/l, y/l at point η are expressed by Eq. (9), and the dimensionless bending stress lσ M /ED o is expressed by Eq. (10). www.nature.com/scientificreports/ Large deflection deformation. Figure 3 illustrates the aspects of large deflection deformation when the dimensionless load α o is varied between 2, 4, 6, and 8, with taper ratios ξ of 0.2, 0.6, and 1.0. The dimensionless load α o used in this study is based on the values used in previous studies 20,21,26 . When the taper ratio was large and the shape was close to a cylinder, the rod deflected greatly from the root, while the deformation behavior changed as the diameter ratio decreased and the shape approached a cone, bending considerably near the tip.
Ohtsuki and Takeuchi 21 showed that the analytical large deformation behaviors of tapered rods are in agreement with the experimental solutions. Figure 4 illustrates the bending stress lσ M /ED o versus relative height η curve obtained by varying the taper ratio ξ between 0.2, 0.6, and 1.0 and the dimensionless load α o between 2, 4, 6, and 8. When the taper ratio is large and the shape is close to cylindrical, the stress decreases monotonically with increasing height. However, when the taper ratio is small and the shape is close to conical, the stress tends to increase and then decrease, and as α o increases, the maximum value moves toward the large end where the stiffness is large. This extreme value shift is the result of flexure, which effectively suppresses the increase in bending stress in response to an increased load. Figure 5a shows the maximum value of the dimensionless bending stress lσ M /ED o | max for each taper ratio obtained by varying the dimensionless load α o as 2, 4, 6, and 8. The analysis yielded a taper ratio with the minimum lσ M /ED o | max corresponding to α o . We refer to this taper ratio as the optimal taper, [D 2 /D 1 ] opt . Furthermore, [D 2 /D 1 ] opt is proportional to α o , and Eq. (11) is derived using the linear approximation with the least-squares method (Fig. 5b).

Shape optimization of tapered solid rods.
Shape optimization of tapered hollow rods. In this section, the mechanical rationality of slender tapered hollow rods is examined from the viewpoint of the optimal taper mentioned above. Let D ′ (s) be the outer diameter of a tapered solid rod when it is transformed into a tapered hollow rod under equal volume and height   Transforming the right-hand side of Eq. (8) to obtain Eq. (12) gives a nonlinear differential equation (Eq. 13). Therefore, taking the effect of the hollow into account, we can derive an expression for the optimal taper (Eq. 14). Figure 6 shows a 3D plot of the optimal taper of a tapered hollow rod from Eq. (14). The smaller β and the more hollow it is, the smaller the variation of the optimal taper [D 2 /D 1 ] opt with load change. In other words, the hollow structure exhibits mechanically superior structural properties in that it minimizes the bending stress equally over a wide range of loading conditions.

Mechanical properties of bamboo and their use in fishing rods
Surrounded by the sea on all sides, Japan has one of the world's most prosperous fishing cultures. Bamboo is abundant, light, strong, rigid, and easy to work and meets all the requirements of materials for fishing rods. It is needless to say that the high affinity of bamboo as a material for fishing rods blossomed as a popular culture in the Edo period and played a role in the unique development of bamboo rods up to the present day (Fig. 1).  www.nature.com/scientificreports/ Present-day fishing rods are typically made of CFRP and GFRP, however, bamboo rods are still treasured, and the techniques have been handed down from generation to generation. Of course, in terms of "unbreakable", bamboo rods will never surpass CFRP or GFRP fishing rods. So why have bamboo rods been loved for so long? This is because there is an affinity between bamboo and fishing as a structure that goes beyond the material. As shown in this study, the tapered shape of the slender rod effectively suppresses the increase in bending stress with increasing load, and the hollow structure provides not only their own weight reduction but also flexible response to a wide range of loading conditions. In addition, the thinner the hollow structure, the more likely it is to be affected by geometric nonlinearity and cause local buckling. However, actual bamboo has a relatively thick-walled cylindrical structure with a hollow ratio of approximately 0.1, although there are some differences among species and individuals 27 . As a result of repeated self-optimization over a long period of time, bamboo has acquired an exquisite structural balance that is ideal for slender tapered hollow rods with highly refined strength and weight, and can be applied to fishing rods for various fish species and fields.
To reveal and utilize the inherent mechanical rationality of living things is no mean feat even with modern technology, and we have great respect for the deep knowledge of natural materials and advanced technology of our ancestors that made this possible.

Method
Equation (8) is a nonlinear differential equation with η as a variable and is difficult to solve analytically. Therefore, the Runge-Kutta method was used to obtain a direct numerical solution, as in previous studies 20,21,26 . The numerical program Mathematica was used for the analysis.

Conclusions
This study revealed the mechanical advantages of bamboo rods from the viewpoint of material mechanics. The findings of this study are summarized as follows.
(1) The shape of the deflection curve and bending stress curve depends on the taper ratio and dimensionless load. (2) Slender tapered rods effectively suppress the stress increase by moving the position of maximum bending stress generation toward the root, which has higher rigidity, in response to an increase in external force. (3) The shape of the slender rod was optimized by changing the taper and dimensionless load under equal volume and height conditions. In addition, considering the hollowing of the rods, the optimal taper was derived from the dimensionless load and hollowing ratio. (4) It was shown that the bending stress could be minimized equally for various ranges of loading conditions by hollowing out slender tapered rods. (5) In the regions where bamboo flourished, the origin of the fishing rod was bamboo rods. This is because there is an affinity between the two as a structure that goes beyond the material.
In this study, only simulations were conducted, and no experimental studies using actual bamboo rods were performed. The specifications of bamboo rods vary greatly depending on the target fish species and fields. Therefore, experimental verification of the findings of this study will be achieved in future.