Abstract
In this paper, we propose a method of designing ultrawideband singlelayer metasurfaces for crosspolarization conversion, via the introduction of Fano resonances. By adding subbranches onto the unit cell structure, the induced surface currents are disturbed, leading to coexistence of both bright and dark modes at higher frequencies. Due to the strong interaction between the two modes, Fano resonance can be produced. In this way, five resonances in all are produced by the singlelayer metasurface. The first four are conventional and are generated by electric and magnetic resonances, whereas the fifth one is caused by Fano resonance, which further extends the bandwidth. A prototype was designed, fabricated and measured to verify this method. Both the simulated and measured results show that a 1:4.4 bandwidth can be achieved for both x and ypolarized waves, with almost all polarization conversion ratio (PCR) above 90%. This method provides an effective alternative to metasurface bandwidth extension and can also be extended to higher bands such as THz and infrared frequencies.
Similar content being viewed by others
Introduction
Metamaterials refer to artificial objects exhibiting intriguing properties which do not exist in nature^{1,2,3,4}. Metamaterials can achieve a mass of exotic physical effects, such as polarization conversion^{5,6,7}, negative refraction^{8}, perfect absorber^{9,10} and so on. In order to reduce bulky volume and be more suitable for application, a twodimensional form of metamaterial is generated, called as metasurface, which is a planar array composed of subwavelength metamaterial units. In the past decade, study of polarization converter is quite familiar to scientific community, but it is still a key issue in electromagnetic (EM) wave. Many meaningful and excellent works have been proposed such as lineartolinear, lineartocircular and dualband polarization^{11,12,13,14,15}. If a facile structure can achieve more wideband and higherefficiency simultaneously, it will further promote the development of various polarization manipulating devices such as highefficient circularly polarized antennas^{16,17}, more reduction of radar cross section (RCS)^{18,19}, and even to construct more complex EM waves^{20}.
Many polarization converters based on anisotropic metasurfaces^{21,22} and chiral metasurfaces^{23,24} have been accounted. However, these polarizers suffer from either the narrow bandwidth or the lowefficiency, which extremely limit their practical applications. One method to extend the bandwidth is to stack multilayers^{25}, which will lead to bulky thickness and difficult preparation. The other method is to use multiple resonances. Chen et al.^{6} have indicated that an ultrawideband metasurface can achieve a 1/4 3 dB bandwidth through four electric and magnetic Lorentzian resonances but the polarization conversion ratio (PCR) is only above 50%. Therefore, it is a priority for us to expand bandwidth under the condition of maintaining the highefficiency.
Fano resonances have been research hotspots recently, due to their capability of providing ultranarrow spectral linewidth and hence various potential applications such as sensing, slow light, and nanolasing^{26,27,28}. Fano resonances is viewed as a quantum interference between a discrete state and a continuum state in atomic physics^{23,29,30}. The shape of Fano resonance is distinctively different from the most common observed spectral line shapes known as symmetric Lorentzian line shapes. It is characterized by an asymmetric spectral shape and have been achieved in various electromagnetic metamaterial structures^{31}.
At present, most wideband polarization rotators are created by increasing the number of Lorentzian resonances but seldom involve Fano resonances^{5,6,18,19,32,33}. In this paper, we aim to further extend the bandwidth via the introduction of Fano resonance. To this end, we first give an optimized doublehead arrow (hereafter called unit 1) that consist of one long straight cutwire and two oblique Vshaped wires, according to multiple plasmon resonances of Chen et al.^{6}. Next, two subbranches are added to the unit 1, generating a composited structure (hereafter called unit 2). When combine them together, the canceling current will be formed between the branch and subbranch, which can be regarded as dark mode, as shown in Fig. 1. Due to the strong interaction between the bright and dark modes, Fano resonance can be produced. Ultimately, after optimization design, a singlelayer ultrawideband linear polarization conversion is proposed. It is demonstrated that five resonances in all are produced by the singlelayer metasurface. The first four are conventional and are generated by electric and magnetic resonances, whereas the fifth one is caused by Fano resonance, which further extends the bandwidth for crosspolarization reflection. Both the simulated and measured results show that a 1:4.4 bandwidth can be achieved for both x and ypolarized waves, with almost all polarization conversion ratio (PCR) above 90%.
Theory design
Chen et al.^{6} have indicated that the bandwidth can be broadened through multiple plasmon resonances. On the basis of it, we give the unit 1 shown in Fig. 2a. The periodicity of unit 1 is 12.2 mm. Unit 1 can be divided into four layers. The thickness of the top copper pattern and background sheet is 0.018 mm with a conductivity of \(5.8\times {10}^{7} \)S/m. There are 0.5 mm F4B dielectric layer (a dielectric constant 2.65 and a loss tangent 0.001) and 8.0 mm foam layer (a dielectric constant 1) in the middle of them. The other parameters are e = 13.7 mm, f = 6.95 mm, g = 0.70 mm, m = 0.30 mm, r = 0.5 mm. Then, fullwave simulations are performed using the frequency domain solver in CST Microwave Studio with periodic boundary conditions in x and ydirections and open conditions along the zdirection. The polarization conversion properties are studied by the reflection coefficients. \({r}_{yy}\)(\({r}_{xx}\)) is the copolarization reflection coefficient and \({r}_{xy}\)(\({r}_{yx}\)) is the crosspolarization reflection coefficient under y (x) polarized wave. As shown in Fig. 2b, unit 1 has a 10 dB bandwidth from 2.91 GHz to 11.88 Hz with four Lorentzian resonances.
On the other hand, hoping to get Fano resonance to broaden bandwidth of polarization conversion, two subbranches are added to the unit 1, generating the unit 2 depicted in Fig. 2c. The unit 2 is periodically arranged along the x and ydirections with a periodicity of p = 12.2 mm. Top layer is a 0.018 mm metal pattern, whose geometrical parameters are illustrated as follows: a = 6.95 mm, b = 2.82 mm, c = 13.7 mm, d = 0.5 mm, k = 0.7 mm, l = 2.51 mm, r = 0.5 mm. The second layer is F4B dielectric spacer with a thickness \({h}_{1}\)=0.5 mm. The third layer is foam substrate with a thickness \({h}_{2}\)=7.6 mm. And the bottom layer is a 0.018 mm copper ground sheet. Figure 2d shows the simulated crosspolarized reflection coefficients is more than − 1 dB from 3.01 GHz to 13.40 GHz for both ypolarized and xpolarized incident waves. Compared with Fig. 2b, we find that unit 2 does have one more resonance after adding two subbranches and the bandwidth is further expanded, indeed.
The PCR is used to evaluate the performance of the polarization conversion, which is defined as \(PCR={r}_{yx}^{2}/{(r}_{yx}^{2}+{r}_{xx}^{2})\). Therefore, we calculate the simulated PCR shown in Fig. 2h and find that almost all PCR is above 90% in the frequency range from 3.05 GHz to 13.40 GHz (about 1:4.4 bandwidth). The PCR can reach 100% in the frequency of 3.25 GHz, 4.81 GHz, 8.24 GHz, 11.69 GHz, and 13.30 GHz, respectively.
To better understand the principle of polarization conversion, u and vcoordinate system is introduced. The vaxis is along 45° direction with respect to the yaxis and uaxis is perpendicular to vaxis, as shown in Fig. 2e. Then, we consider that the incident EM wave is polarized along the yaxis. The electric field can be decomposed into two orthogonal components (directions u and v). Hence, the electric field of the incident EM wave can be expressed as \(\overrightarrow{\mathrm{E}}=\overrightarrow{u}{\mathrm{E}}_{iu}{e}^{j\varphi }+\overrightarrow{v}{E}_{iv}{e}^{j\varphi }\), where \(\overrightarrow{u}\) and \(\overrightarrow{v}\) are the unit vectors in the u and vaxes, respectively. The electric field of the reflected wave can be written as \(\overrightarrow{{E}_{r}}={r}_{u}\overrightarrow{u}{\mathrm{E}}_{iu}{e}^{j\varphi }+{r}_{v}\overrightarrow{v}{E}_{iv}{e}^{j\varphi }\), in which \({r}_{u}\) and \({r}_{v}\) are the reflection coefficients along the u and vaxes, respectively. Due to the anisotropic characteristic of the metasurface, a different phase change \(\mathrm{\Delta \varphi }\) can be generated. Therefore, when \(\mathrm{\Delta \varphi }\approx\uppi \) and amplitude satisfy \({\mathrm{r}}_{\mathrm{u}}\approx {\mathrm{r}}_{\mathrm{v}}\), the field synthesized by \({E}_{ru}\) and \({E}_{rv}\) will be along the xdirection. The incident polarization is rotated by 90°. To verify the polarization conversion performance of the unit 2, we carried out numerical simulations of reflection phase and amplitude characteristics. As displayed in Fig. 2(f), the reflection amplitudes of u and vpolarized waves are basically equal and we get 180°−39°\(\le \mathrm{\Delta \varphi }\le \) 180° + 39° in Fig. 2(g) from 3.01 GHz to 13.40 GHz. Moreover, the minimum value of \({r}_{yy}\) almost appears at the frequency where \(\mathrm{\Delta \varphi }\) is equal to 180°, further proving the correctness of the proposed criterion.
Simulated results analysis
The curve of Fano resonance is asymmetry, which is a typical feature different from that of conventional symmetric resonance curves. As shown in Fig. 2d, the fifth resonance is asymmetry because of the dramatically decrease at the fifth resonance. Therefore, we can predict that unit 2 has a Fano resonance. In order to validate this, we study the resonance eigenmodes of unit 2 using CST Microwave Studio. The electric field component along u and vaxes can excite resonant eigenmodes. Figure 3a,b present the simulated results, indicating that there are five dips. The three eigenmodes (i), (iii) and (v) are excited by upolarized EM waves while the other two eigenmodes (ii) and (iv) are excited by vpolarized EM waves. Thus, when the ypolarized waves are incident, five resonances can be excited simultaneously because the ypolarized waves have both u and vcomponents. However, there is a special resonance, the eigenmode (v). We find that copolarization reflection in (v) is far less than others. It means the resonance in (v) is fundamentally different from the other resonances.
In order to judge what type of each resonance, it is better to analyze surface current distributions. Therefore, we monitor the surface currents at each eigenfrequency as shown in Fig. 4. The first four resonances are analyzed firstly in Fig. 4a. Meanwhile, the surface current distributions of unit 1 are given in Fig. 4b regarded as comparisons. At the end of this section, the fifth resonance will be discussed.
Magnetic resonances are generated by antiparallel currents coupling between top metal pattern and the background sheet. Electric resonances are generated by parallel currents. Fano resonance can be introduced by the strong interaction between bright and dark modes. More intuitively, Fano resonances can be caused by the interaction between the electric dipoles^{34,35}.
Aiming to make it more intuitive, the partial surface current is shown by the arrows painting in the Fig. 4. We can regard Vshaped resonator as evolvement from cutwire resonator and the Vshaped resonator will function as an extended cutwire resonator in the vdirection. Therefore, in Fig. 4a, the magnetic resonance is generated by antiparallel surface currents induced by extended cutwire resonator and the ground sheet for (i) and (ii). And the electric resonance is generated by parallel surface currents induced by extended cutwire resonator and the ground sheet for (iii). In (iv), according to the vector synthesis principle, two red arrows can be combined into a blue one and two blues constitute one black. The overall direction of surface current is still down to the left, which means it is parallel surface currents induced along resonator and the ground sheet. Therefore, it is still an electric resonance.
Besides, we also simulate the surface current distributions of unit 1 shown in Fig. 4b aiming to figure out what causes the Fano resonance. As is indicated by the above analysis, (i) and (ii) are magnetic resonance while (iii) and (iv) are electric resonance. Compared with the Fig. 4a (i)–(iv), the four resonance types of the unit 1 are basically same as the first four resonance of unit 2. Hence, it is the two subbranches resonators that cause the Fano resonance.
Fano resonances suggest a good approximation of constructive and destructive interference of discrete states and continuum states, which are viewed as dark modes and bright modes^{36,37}. From the Fig. 5a, the part that is circled in the middle can be seen as a “bright mode” for the parallel currents on both sides of the cutwire. The other two circled parts can be regarded as “dark modes” because the opposite currents cancel each other out. The special structure of unit 2 leads to coexistence of both bright and dark modes at higher frequencies. Due to the strong interaction between the two modes, Fano resonance can be produced.
On the other hand, Fano resonances also can be intuitively explained by the coupledmode theory of two classical Lorentzian oscillators with electromagnetic waves as driving force. In a case of two coupled oscillators, there are effectively two driving forces acting on the first oscillator, which are out of phase and cancel each other^{38,39,40}. It can be seen from the Fig. 5b, there are both u and vdirection of the surface current components in the ground sheet. In the vdirection of Fig. 5a, the surface current component is parallel to that in the middle part of unit 2 (green arrow), which will form an electrical resonance. In the udirection, it is different for the surface currents between both sides of the cutwire structure. From the color we can realize that the redder the color, the greater the current. Main surface currents are centralized on one side while there's almost nothing on the other side. Therefore, according to the vector synthesis principle, the main surface currents in vdirection are the two red arrows, which are parallel to vdirection surface current component in the ground sheet. Then, electrical resonances in the udirection are formed. It is the interaction between the electric dipole and the quadrupole that causes Fano resonance with an asymmetrical spectrum. In conclusion, the first four resonances result in expansion of the operating frequency range because they are generated by electric and magnetic resonances. The fifth resonance is Fano resonance caused by interaction between dark modes and bright modes, which leads to further expansion of bandwidth.
It is worth mentioning that the length of oblique Vshaped wires (parameter b) is a critical factor affecting the bandwidth and the performance of Fano resonance. As exhibited in Fig. 6a,b, we simulate the co and crosspolarization reflection when parameter b is 0, 1.5, 2.0, 2.3, 2.8, 3.3. Compared b = 1.5 with b = 0 in Fig. 6a,b, we find that an obviously asymmetric spectral shape appears from 16 to 18 GHz and it is a typical characteristic of the Fano resonance. It is proofed again that the two Vshaped subbranches resonators cause the Fano resonance. Furthermore, we find that the adjustment of parameter b can almost independently change the frequency of Fano resonance, and the resonant frequency will decrease with the increase of parameter b while have almost no effect on the first four resonances. Although the Fano resonance has a characteristic of narrow band, it still can be regarded as a method to further expand bandwidth on the basis of an ultrawideband polarization conversion metasurface. Hence, in the principle of ensuring high efficiency while maximizing bandwidth, we successfully connect the narrow band of the Fano resonance with the wide band caused by the first four Lorentz resonances by adjusting parameter b to 2.8, as shown in the green lines of Fig. 6a,b. In Fig. 6b, the cross polarization of b = 2.8 does increase by a peak around 13.3 GHz compared with b = 0 and b = 1.5. Meanwhile, in the process of changing parameter b as shown in Fig. 6c, we find that the effect of Fano resonance will achieve best when the line between points A and B is approximately perpendicular to the cutwire. This will provide a more intuitive strategy of the design in the future.
Experiment results
To further verify the properties, we fabricate an area of 427 mm*427 mm square prototype of the polarization conversion metasurface as shown in Fig. 7a. The sample is measured using two horn antennas and the Agilent E8363B network analyzer, which is surrounded by absorbing materials to avoid unwanted reflections from the environment. The experimental setup with measurements is shown in Fig. 7b. In the process of experiment, one horn antenna is used as the transmitting antenna and the other is used for receiving antenna. We can obtain the copolarization reflective coefficients by placing the both antenna on longer sides. The crosspolarization reflective coefficients can be obtained by placing one antenna on its longer side and placing the other antenna on its shorter side.
Both the simulated and measured results are presented in Fig. 7c. The simulated and measured PCR is also given in Fig. 7d. Compared with simulated results, we find that the measured copolarization reflection is a little bit higher than that of simulation and the measured PCR is less than theoretical value. After further simulation and experimental verification, the little difference between measurement and simulation is caused by the distance between F4B layer and copper ground sheet. When the distance is greater than \({h}_{2}\), the last peak will be above theoretical value leading to the decrease of PCR. It is the hardcontrollable thickness of foam and the interval between layers that lead to deviating from the theoretical value. On the other hand, the crosspolarization reflections are roughly the same as the theoretical value exhibiting a higher capacity of polarization conversion. In general, the experiment results are in agree with simulation results, which further verify that unit 2 has a wide and efficient bandwidth for both normally incident x and ypolarized waves.
Conclusion
The novelty in terms of mechanism of this paper is the introduction of Fano resonance to expand bandwidth because Lorentzian resonances are often used to expand bandwidth but Fano resonances are seldomly used. Besides, compared with Chen et al.^{6}, the structure proposed this paper has a better performance. Ref.^{6} has a 1:4 bandwidth with PCR above 50%, while we have a 1:4.4 bandwidth with almost all PCR above 90%. Table 1 presents a comparison between the proposed reflective linear polarization converter and other reported ones operated in microwave frequency ranges. From Table 1, it can be observed that the proposed converter has an ultrabroadband and highefficiency performance. In general, highefficiency comes at the decrease of bandwidth. But we achieve highefficiency and wideband simultaneously.
Furthermore, the linear polarization conversion metasurface is a very basic work and if the foundation work is improved, any practical application of the foundation work will be expanded. For example, it can be used to achieve more radar cross section (RCS) reduction by combining with its 90°, 180° and 270° rotated ones to create the destructive interferences cancellation. Meanwhile, the proposed structure is a potential candidate for many polarization control devices due to its ultrawideband and high efficiency performance or ultrasensitive sensors because the energy of Fano resonances is strongly confined which is suitable for switching devices, sensors, isolators, etc. This work also provides a notable avenue to metasurface bandwidth extension using Fano resonances and can also be extended to higher bands such as THz and infrared frequencies.
References
Pendry, J. B. Negative refraction makes a perfect lens. Phys. Rev. Lett. 85(18), 3966 (2000).
Smith, D. R. Composite medium with simultaneously negative permeability and permittivity. Phys. Rev. Lett. 84, 4184 (2000).
Chen, L. et al. Spaceenergy digitalcoding metasurface based on an active amplifier. Phys. Rev. Appl. 11(5), 054051 (2019).
Li, W. H., Qiu, T.S., & Qu, S. B. Programmable coding metasurface reflector for reconfigurable multibeam antenna application, https://doi.org/10.1109/TAP.2020.3010801 (2020).
Feng, M. D. & Wang, J. F. Broadband polarization rotator based on multiorder plasmon resonances and high impedance surfaces. J. Appl. Phys. 114, 074508 (2013).
Chen, H. Y. & Qu, S. B. Ultrawideband polarization conversion metasurfaces based on multiple plasmon resonances. J. Appl. Phys. 115, 154504 (2014).
Li, S. J., Cui, T. J. & Cao, X. Y. Multiband fractal metasurface with linear to linear and linear to circular polarization conversion. in Photonics & Electromagnetics Research Symposium  Fall (PIERS  Fall). (IEEE, New York, 2020).
Cheng, Q. & Cui, T. J. Negative refractions in uniaxially anisotropic chiral media. Phys. Rev. B 73(11), 3104 (2006).
Li, Y., Lin, J., Guo, H. A tunable metasurface with switchable functionalities: From perfect transparency to perfect absorption. Adv. Opt. Mater. (2020).
Huang, H., & Wang, W.J. Tunable ultrathin Pband absorber based on permeabilitynearzero metamaterial. in 2017 Sixth AsiaPacific Conference on Antennas and Propagation (APCAP). (IEEE, New York, 2018)
Sun, H. et al. Ultrawideband and broadangle linear polarization conversion metasurface. JAP 121(17), 174902 (2017).
Khan, M. I., Khalid, Z. & Tahir, F. A. Linear and circularpolarization conversion in Xband using anisotropic metasurface. Sci. Rep. 9(1), 1–11 (2019).
Lin, B. Q. et al. Multipleband linearpolarization conversion and circular polarization in reflection mode using a symmetric anisotropic metasurface. Phys. Rev. Appl. 9(2), 024038 (2018).
Yu, Y., Xiao, F., He, C., Jin, R. & Zhu, W. Doublearrow metasurface for dualband and dualmode polarization conversion. Opt. Exp. 28(8), 11797–11805 (2020).
Akram, M. R., Ding, G., Chen, K., Feng, Y. & Zhu, W. Ultrathin single layer metasurfaces with ultrawideband operation for both transmission and reflection. Adv. Mater. 32(12), 1907308 (2020).
Schwanecke, A. S., Fedotov, V. A., Khardikov, V. V. & Zheludev, N. I. Nanostructured metal film with asymmetric optical transmission. Nano Lett. 8(9), 2940–2943 (2008).
Menzel, C. et al. Asymmetric transmission of linearly polarized light at optical metamaterials. Phys. Rev. Lett. 104(25), 253902 (2010).
Wang, Z. X., & Wang, J. F. Multioctave RCS reduction via integrated dispersion engineering of polarizationconversion metasurface and metamaterial absorber. J. Phys. D Appl. Phys. 53(3) (2019).
Ameri, E., Esmaeli, S. & Sedighy, S. Ultra wideband radar cross section reduction by using polarization conversion metasurfaces. Sci. Rep. 9, 478 (2019).
Peng, N. & She, W. Asymmetric optical transmission through periodic arrays of cone air holes in a metal film. Opt. Exp. 22(23), 28452–28458 (2014).
Jin, R. Q. & Wang, S. Y. Ultrabroadband linear polarization converter based on anisotropic metasurface. Opt. Exp. (2018).
Long, F., Yu, S. & Kou, N. Efficient broadband linear polarization conversion metasurface based on %: Shape. Microw. Opt. Technol. Lett. 62(1) (2020).
Liang, P. Metamaterials: Giant asymmetric radiation from an ultrathin bianisotropic metamaterial. Adv. Sci. 5(7), 1870042 (2018).
Ma, Z. J. Alldielectric planar chiral metasurface with gradient geometric phase. Opt. Exp. 26(5), 6067 (2018).
Fu, X. M., Wang, J. F. & Fan, Y. Lightweight ultrawideband radar cross section reduction structure using doublelayer metasurfaces. J. Phys. D Appl. Phys. (2019).
Miroshnichenko, A. E. Fano resonances in nanoscale structures. Rev. Mod. Phys. 82(3), 2257–2298 (2010).
Joe, Y. S. Classical analogy of Fano resonances. Phys. Scr. 74(2), 259–266 (2006).
Lalanne, P., Yan, W. & Vynck, K. Light interaction with photonic and plasmonic resonances. Laser Photon. Rev. 12(5), 1700113.11700113.38 (2018).
Wang, X. B., Li, H. & Zhou, J. Asymmetric transmission in a Miebased dielectric metamaterial with Fano resonance. Materials 12(7), 1 (2019).
Wang, X. B. & Zhou, J. Magnetically tunable Fano resonance with enhanced nonreciprocity in a ferritedielectric metamolecule. Appl. Phys. Lett. 112(17), 174103.1174103.3 (2018).
Singh, R. Sharp Fano resonances in THz metamaterials. Opt. Exp. 19(7), 6312–6319 (2011).
Hoa, N. T. Q., Tuan, T. S. & Hieu, L. T. Facile design of an ultrathin broadband metamaterial absorber for Cband applications. Sci. Rep. 9(1), 1 (2019).
Khan, M. I. & Tahir, F. A. A broadband crosspolarization conversion anisotropic metasurface based on multiple plasmon resonances. Chin. Phys. B 27(1), 14101–014101 (2018).
Fu, X. M. & Wang, J. F. Merging bands of polarization convertors by suppressing Fano resonance. Appl. Phys. Lett. 113(10), 101901 (2018).
Fan, J. A. Fanolike Interference in selfassembled plasmonic quadrumer clusters. Nano Lett. 10(11), 4680 (2010).
Cirelli, C., Marante, C. & Heuser, S. Anisotropic photoemission time delays close to a Fano resonance. Nat. Commun. 9(1), 955 (2018).
Deng, Z. L. & Fu, T. Trimeric metasurfaces for independent control of bright and dark modes of Fano resonances. Appl. Phys. Lett. 108(8), 139–8034 (2016).
Guo, H. J. et al. Flat optical transparent window: mechanism and realization based on metasurfaces. J. Phys. D Appl. Phys. 51(7), 4001 (2018).
Huang, W. et al. A complete phase diagram for darkbright coupled plasmonic systems: Applicability of Fano’s formula. Nanophotonics 9, 3251 (2020).
Yang, B. W., Liu, T., Guo, H. J., Xiao, S. Y. & Zhou, L. Highperformance metadevices based on multilayer metaatoms: Interplay between the number of layers and phase coverage. Sci. Bull. 64(012), 823–835 (2019).
Acknowledgements
The authors are grateful to the supports from the National Natural Science Foundation of China under Grant Nos. 61971435, 61671466, 61601507, the National Key Research and Development Program of China (Grant No.: SQ2017YFA0700201).
Author information
Authors and Affiliations
Contributions
Z.Z. write the main text. J.W., H.C, M.F and S.Q provide theoretical guidance. X.F., Y.J. and R.Z. direct simulation and experiment. All authors reviewed the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhang, Z., Wang, J., Fu, X. et al. Singlelayer metasurface for ultrawideband polarization conversion: bandwidth extension via Fano resonance. Sci Rep 11, 585 (2021). https://doi.org/10.1038/s41598020799450
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598020799450
This article is cited by

Recent progress in Fanoresonant terahertz metasurface and its application
Discover Applied Sciences (2024)

Broadband and highefficiency polarization conversion with a nanokirigami based metasurface
Scientific Reports (2023)

Experimental demonstration of multiple Fano resonances in a mirrored array of splitring resonators on a thick substrate
Scientific Reports (2022)

A Terahertz Tunable Metamaterial Reflective Polarization Converter Based On Vanadium Oxide Film
Plasmonics (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.