Correction to: Scientific Reports https://doi.org/10.1038/s41598-020-65073-2, published online 15 May 2020
This Article contained errors in the order of the Figure legends.
The Figure 1 legend was incorrectly given as the Figure 2 legend; The Figure 2 legend was incorrectly given as the Figure 3 legend; The Figure 3 legend was incorrectly given as the Figure 4 legend; The Figure 4 legend was incorrectly given as the Figure 5 legend; The Figure 5 legend was incorrectly given as the Figure 6 legend; The Figure 6 legend was incorrectly given as the Figure 7 legend; The Figure 7 legend was incorrectly given as the Figure 8 legend; The Figure 8 legend was incorrectly given as the Figure 9 legend; The Figure 9 legend was incorrectly given as the Figure 10 legend; The Figure 10 legend was incorrectly given as the Figure 11 legend; The Figure 11 legend was incorrectly given as the Figure 12 legend; The Figure 12 legend was incorrectly given as the Figure 13 legend; The Figure 13 legend was incorrectly given as the Figure 1 legend.
The correct order of the Figure Legends is listed below:
Figure 1. Elemental distribution analysis results of as-built equiatomic CoCrFeMnNi high-entropy alloy using back scattered electron (BSE) – energy dispersive X-ray spectroscopy (EDS) mapping.
Figure 2. (a) X-ray diffraction (XRD) patterns and (b) EBSD phase map of as-built sample (HAGB: high angle grain boundary).
Figure 3. Three-dimensional EBSD IPF/BD maps of selective laser-melted equiatomic CoCrFeMnNi high-entropy alloy.
Figure 4. Electron channeling contrast images showing (a) the cellular structure and (b) the columnar structure in the as-built sample.
Figure 5. (a) Scanning transmission electron microscopy (STEM) image and corresponding Mn-O elemental distribution maps and (b) high resolution TEM (HR-TEM) images and FFT pattern of the selected square region in the HR-TEM image.
Figure 6. (a) Typical compressive stress-strain curves and (b) yield strengths at various temperatures.
Figure 7. Enlarged compressive stress-strain curves showing the serrated flow.
Figure 8. True stress-strain curves of selective laser-melted equiatomic CoCrFeMnNi high-entropy alloy at various temperatures.
Figure 9. Typical EBSD IPF maps showing the deformation microstructure of SLM-built equiatomic CoCrFeMnNi high-entropy alloy.
Figure 10. Typical EBSD RF maps showing the deformation microstructure of SLM-built equiatomic CoCrFeMnNi high-entropy alloy. The fraction of deformed, substructured, and recrystallized grains was calculated using a recrystallization map component in Tango after keeping a minimum misorientation angle of 2 deg. to separate sub-grains and 15 deg. to separate grains.
Figure 11. ECC images of SLM-built HEAs after compressive deformation at various temperatures.
Figure 12. EBSD IPF map (a), GNDs distribution maps (b), and RF map of deformed sample at 700 °C.
Figure 13. Raw equiatomic CoCrFeMnNi HEA pre-alloyed powders: (a) SEM morphology, (b) SEM-EDS mapping results, and (c) particle size distributions.
These errors have now been corrected in the HTML and PDF version of the Article.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kim, YK., Yang, S. & Lee, KA. Author Correction: Superior Temperature-Dependent Mechanical Properties and Deformation Behavior of Equiatomic CoCrFeMnNi High-Entropy Alloy Additively Manufactured by Selective Laser Melting. Sci Rep 10, 18006 (2020). https://doi.org/10.1038/s41598-020-69894-z
Published:
DOI: https://doi.org/10.1038/s41598-020-69894-z
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.
