Extrapolation of cell culture-based test results to in vivo effects is limited, as cell cultures fail to emulate organ complexity and multi-tissue crosstalk. Biology-inspired microphysiological systems provide preclinical insights into absorption, distribution, metabolism, excretion, and toxicity of substances in vitro by using human three-dimensional organotypic cultures. We co-cultured a human lung equivalent from the commercially available bronchial MucilAir culture and human liver spheroids from HepaRG cells to assess the potential toxicity of inhaled substances under conditions that permit organ crosstalk. We designed a new HUMIMIC Chip with optimized medium supply and oxygenation of the organ cultures and cultivated them on-chip for 14 days in separate culture compartments of a closed circulatory perfusion system, demonstrating the viability and homeostasis of the tissue cultures. A single-dose treatment of the hepatotoxic and carcinogenic aflatoxin B1 impaired functionality in bronchial MucilAir tissues in monoculture but showed a protective effect when the tissues were co-cultured with liver spheroids, indicating that crosstalk can be achieved in this new human lung–liver co-culture. The setup described here may be used to determine the effects of exposure to inhaled substances on a systemic level.
The often-limited translatability of data obtained in preclinical in vivo studies to the human situation and the restricted physiological relevance of current in vitro assays call for more predictive test methods. Microphysiological systems are in vitro models that better reflect the cellular microenvironment found in vivo. In comparison with conventional static in vitro organ models, medium flow in microphysiological systems removes microenvironments that can form around the cultures, improving nutrient and oxygen supply. Moreover, organ perfusion enables the creation of microenvironmental biomolecular gradients and relevant mechanical cues. These systems are regarded as ground-breaking in preclinical validation of substances and have the potential to change and accelerate drug development significantly. The number of publications on this topic has increased steadily since the first single-organ-on-a-chip study published by Michael Shuler’s group in 20041. In addition to a wide variety of publications on single-organ-on-a-chip systems2,3,4, reports of multi-organ chips (MOCs) are increasing, as they can also emulate organ–organ crosstalk. Here, several organ equivalents are connected by microfluidic channels and can interact through the flow of culture medium. This, furthermore, allows investigation of pharmacokinetic parameters, such as absorption, distribution, metabolism, and excretion5,6,7,8. Successful homeostatic long-term organotypic co-cultures of human skin samples with three-dimensional (3D) human liver spheroids on a commercially available MOC platform have already been described9. Other MOC-based long-term co-cultures of various organ combinations have been established, such as liver spheroids with human 3D intestinal10, neuronal11, and pancreatic islet12 tissue models and a skin–intestine–liver–kidney13 chip for complex multi-tissue testing of substances. We recently reported a first repeated-dose test for simultaneous generation of safety and efficacy data using a MOC platform adapted for co-culturing human H292 lung cancer microtissues and human full-thickness skin equivalents14.
Here, we describe a novel MOC connecting a 3D air–liquid interface bronchial model with liver spheroids to assess the potential toxicity of inhaled substances under conditions that permit organ crosstalk. Such 3D bronchial models can be generated by cultivating human primary bronchial epithelial cells on porous carriers at the air–liquid interface15. Once exposed to air, the cells will differentiate and pseudostratify, forming a 3D tissue resembling the in vivo tissue. These models have been widely used to mimic human respiratory diseases, such as chronic obstructive pulmonary disease, asthma, rhinosinusitis, and cystic fibrosis16. Because of the latest developments in microphysiological system engineering, it is now also possible to imitate blood circulation and physical movements of the tissues, which, for example, influence the permeability of bronchial epithelium17,18,19. In the context of toxicological assessment, these 3D lung models cultured under conventional static conditions are inaccurate, as they only replicate the primary effects of inhaled substances, and the toxicity of these substances can be influenced by other organs once in the bloodstream.
The liver expresses approximately 30 cytochrome P450 (CYP) enzymes and, therefore, plays a decisive role in metabolizing substances20. Several groups have developed platforms to mimic the human liver in combination with other organs such as the lungs1,21,22. Major efforts in this area have been directed towards drug metabolism and toxicity studies by using primary human liver cells or hepatoma cell lines23,24. In this study, we used spheroids formed from HepaRG cells and primary human hepatic stellate cells (HHSteCs). HepaRG is a carcinoma cell line that bears characteristics similar to those of primary human hepatocytes and has been used successfully in drug metabolism and toxicity studies25,26,27. These cells have also been shown to form 3D spheroids with better functional performance than that of standard two-dimensional models in static cultures27,28,29.
In the present study, we demonstrated the stability and functionality of the two models cultured in a specifically designed MOC over 14 days. This MOC included a large medium reservoir and an air-permeable membrane above the lung culture compartment to ensure optimal air circulation. The surface area of the bronchial MucilAir model used was 0.33 cm2, corresponding to 1/100,000 of the surface area of the entire respiratory tree without the alveolar surface area. The number of liver cells used per chip represents a similar proportion in a normal human liver. Aflatoxin B1 (AFB1) was used to demonstrate organ interaction. We found that the toxicity of 5 µM AFB1 decreased in the presence of the liver spheroids, confirming that this lung–liver co-culture system can be used to evaluate the toxicity of inhaled substances.
Oxygen pressure (pO2) dynamics in the Chip3plus
A HUMIMIC Chip3plus (TissUse GmbH, Berlin, Germany) was designed which allows for the co-culture of lung and liver tissues to obtain more complex and physiologically relevant tissue responses after exposure to inhaled toxicants (Fig. 1). Tissue culture conditions such as pH, temperature, and oxygen supply affect cell behaviour and, therefore, emulation of the in vivo situation. We, therefore, monitored the pO2 and its dynamics using oxygen sensors (PreSens Precision Sensing GmbH, Regensburg, Germany) at various locations inside the Chip3plus. The pO2 was measured at the bottom of the medium reservoir to determine partial pO2 within the medium and underneath the lid of the lung culture compartment to monitor pO2 in the air inside the chip (Fig. 2A). First, baseline levels in a cell-free Chip3plus were investigated over 5 days, and the pO2 remained stable at both locations over the cultivation period. The pO2 was measured as 200 hPa in the air under the lid and 210–220 hPa in the culture medium, indicating that the atmospheric pO2 value outside the incubator (approximately 215 hPa, 21% oxygen at an average pressure of about 1 atm) was maintained in the Chip3plus over the testing period. We noted that the pO2 values did not decrease to match the pO2 value in the incubator (185–192 hPa, depending on the air pressure). It can, therefore, be assumed that gas diffusion from the incubator air through the polydimethylsiloxane (PDMS) channel walls of the chip did not occur. This indicates the presence of oxidized PDMS, which was reported to have a significant smaller diffusion coefficient of the oxygen compared to non-oxidized PDMS30.
The experiment was repeated over a period of 14 days with the lung–liver co-culture (Fig. 2B). The cell culture medium was exchanged three times a week to ensure sufficient nutrient supply to the tissues. This required opening of the culture compartments under sterile conditions. Consequently, the air inside the chip was replaced with fresh room air at each medium renewal, and the pO2 returned to atmospheric levels. The air pO2 dropped rapidly in the lung culture compartment between medium exchanges. Within 2 days, we observed a decrease from 200 hPa to below 130 hPa, which is the lowest pO2 detected in the lungs in vivo at sea level and occurs in the alveoli31. The pO2 in the medium reservoir remained relatively constant between medium exchanges, at around 200 hPa.
Given the rapid decrease in pO2 observed in the air of the lung culture compartment (Fig. 2B), we investigated the effect of a gas-permeable membrane covering the compartment instead of using an airtight lid on oxygenation (pO2). In the first setting, the pO2 was measured only in the presence of the bronchial MucilAir culture, followed by an experiment where both tissue models—a bronchial MucilAir culture and 40 liver spheroids—were in the chip. Again, the pO2 in the medium was measured at the bottom of the medium reservoir and underneath the lid/membrane of the lung culture compartment. The results for the air pO2 underneath the lid obtained previously were reproduced in the lung monoculture with lid (Fig. 2C). In contrast to the airtight lid, the gas-permeable membrane maintained the air pO2 inside the lung culture compartment stable at about 200 hPa. In addition to the pO2 drop in the lung culture compartment air, the airtight lid also caused a decrease in the pO2 in the medium below the bronchial MucilAir culture. The use of a membrane stabilized the pO2 in the culture medium to a value of 160 hPa, which is below the pO2 values described above for the air and in the medium reservoir. This indicates that oxygen consumption by the bronchial MucilAir culture exceeded the reoxygenation achievable by medium circulation and O2 diffusion.
Subsequently, we investigated the pO2 dynamics in the liver culture compartment. Two replicates of a lung–liver co-culture were used. These were initially cultivated for 3 days with tight plastic lids on the lung culture compartment and then with membranes for 6 days. Over time, the pO2 in the culture medium remained stable on each chip at a comparatively low level of 70–87 hPa for replicate 1 and 40–50 hPa for replicate 2 (Fig. 2D). After starting the pump, the pO2 value in both chips increased by 30%. In contrast, the variability between the chips in the liver culture compartment was quite large. Furthermore, the difference in pO2 observed between the medium reservoir (Fig. 2B) and liver compartment (Fig. 2D) confirmed that the cells in the liver compartment were metabolically active and consumed oxygen. From these measurements, it can also be assumed that spatial pO2 gradients were present in the medium circulating in the chip. No differences in pO2 were observed between liver culture compartments under the airtight lid and the gas-permeable membrane.
Evaluation of liver monocultures in the Chip3plus
We then evaluated various culture conditions using liver spheroids in the Chip3plus (Fig. 3A). When cultivated on the glass surface of the Chip3plus (standard condition), the liver spheroids adhered after a few days, visible as a spread of cells across the glass surface. In some cases, the free-floating liver spheroids also fused, forming large tissues and possibly leading to the formation of necrotic cores. For this reason, we developed a novel approach to maintain the liver spheroids in the Chip3plus: A disk made from polyethylene glycol and containing 40 cavities, each with a diameter of 500 µm, was used as an inlay in the liver culture compartment of the Chip3plus; this was termed SpheroidBrick (Cellbricks GmbH, Berlin, Germany). This inlay is large enough for liver spheroids, while keeping each one separated by the cavity walls. The polyethylene glycol substrate also prevents the liver spheroids from adhering to the surface. As shown by adenosine triphosphate (ATP) measurement, the liver spheroids cultured in the SpheroidBricks were more homogeneous at harvesting than those cultured by using conventional culture methods (Fig. 3B). Lactate dehydrogenase (LDH) release, used as a marker of cytotoxicity, confirmed that the polyethylene glycol-based SpheroidBricks had no major effect on cytotoxicity, as it remained below 10% and even decreased under both conditions over 14 days (Fig. 3C).
Long-term stability of lung–liver co-cultures
Following the initial characterization and adaptation, the suitability of the chip for maintaining mono- or co-cultures for 14 days was assessed. Functional markers and the viability of the liver spheroids were assessed by albumin production, ATP content, and tdT-mediated dUTP-digoxigenin nick-end labelling (TUNEL)/Ki67 staining. The Chip3plus co-cultures were compared with statically cultured liver spheroids in monoculture and baseline (day 0) controls. The liver spheroids were cultured in SpheroidBricks to maintain their 3D morphology, and the HHSteCs were omitted from the spheroids, as HHSteC activation was assumed from upregulation of HHSteC markers (e.g., collagen I) after SpheroidBrick culturing (data not shown). Albumin production was relatively stable over the 14-day test period, at about 6 ± 2 pg/day per HepaRG cell, regardless of whether the cultures were maintained under static or dynamic conditions (Fig. 4A). Lung–liver co-cultures showed lower variability in albumin production over time than static liver monocultures. Moreover, the ATP levels in co-cultured liver spheroids were not substantially different from those in the statically maintained liver spheroid monocultures (Fig. 4B); however, a 35% decrease from baseline was observed under both conditions. These findings support the morphological (data not shown) and immunohistochemical (Fig. 4C) observations that the spheroids cultured under both conditions appeared to become smaller and less dense during culturing. However, liver spheroids from both conditions showed comparable numbers of proliferating cells positively stained for Ki67 and low numbers of apoptotic cells positively stained for TUNEL.
Bronchial MucilAir cultures evaluated through ATP measurement showed that the culturing method (static liver monoculture vs. Chip3plus lung–liver co-culture vs. Chip3plus lung monoculture) and 14-day culturing period had no impact on tissue viability (Fig. 5C). The functionality of bronchial MucilAir cultures was assessed by measuring the ciliary beating frequency and transepithelial electrical resistance. Ciliary beating is a key mechanism of mucociliary clearance and airway defence against inhaled particles and pathogens32. Transepithelial electrical resistance is a marker of tight junctions and biological barrier integrity33. Bronchial MucilAir tissues cultured alone in the Chip3plus were compared with tissues co-cultured with liver spheroids and those cultured under static conditions. The ciliary beating frequency of bronchial MucilAir tissues in static monoculture decreased by approximately 20% from baseline (Fig. 5A), while the transepithelial electrical resistance increased by about 20% at the same time (Fig. 5B). The tissues maintained in the chip under medium flow exhibited no significant changes in transepithelial electrical resistance or ciliary beating frequency over the 14-day culturing, regardless of whether they had been cultured alone or in co-culture.
LDH release into the culture medium was assessed for all four conditions (static lung and liver monocultures, Chip3plus lung–liver co-culture, and Chip3plus lung monoculture). LDH release is widely used as a measure of cell death, as this soluble cytoplasmic enzyme is present in almost all cell types and released into the extracellular space when the plasma membrane is damaged34. A release of about 50 mU LDH/day was detected on the second day of co-culturing, and decreased continuously from day 4 to a 50% lower LDH release on day 14. The same was observed in the liver monocultures, whereas lung monocultures, regardless of their culturing method (static vs. on-chip), exhibited almost no release of LDH into the basolateral medium. It can, therefore, be assumed that the LDH measured in the co-cultures originated primarily from the liver spheroids.
These findings demonstrated that both models could be maintained in co-culture over the 14-day period and that specific organ functions remain relatively stable.
Assessment of AFB1 toxicity in lung–liver co-cultures
AFB1 was selected to demonstrate the crosstalk of the lung–liver co-culture in Chip3plus and its suitability for substance testing. AFB1 is a hepatotoxic compound produced by Aspergillus moulds. Its cytotoxicity and subsequent detoxification are mediated via metabolic activation by drug-metabolizing CYP enzymes24,35,36,37 and has also been shown to occur in human airways38. Moreover, this compound was used recently in a lung–liver chip described by Bovard et al., where cytotoxicity in normal human bronchial epithelial cells cultured at the air–liquid interface was delayed by co-culture with liver spheroids21. We exposed the lung–liver co-cultures and lung monocultures to 5 µM AFB1 after two days of culture in the chip to allow the tissues to adapt to the flow conditions and investigate the short-term effects after 24 h of exposure. This concentration was selected because it is in the range of the half-maximal threshold concentration described for AFB1 treatments of HepaRG cultures24,39. After 24 h of exposure to 5 µM AFB1, a decrease of 1 pg/day/cell in albumin production was observed in the lung–liver co-cultures, indicating impairment of liver function (Fig. 6B). In contrast, intracellular ATP levels in co-cultured liver spheroids treated with AFB1 (Fig. 6C) and LDH release into the co-culture medium (Fig. 6A) were unchanged from those in vehicle controls. Co-cultured bronchial MucilAir cultures treated with AFB1 showed a slight decrease in transepithelial electrical resistance (Fig. 6E) and a moderate increase in ATP content (Fig. 6D) compared with those observed in vehicle controls. Monocultured bronchial MucilAir cultures treated with 5 µM AFB1 exhibited a much stronger decline in transepithelial electrical resistance (Fig. 6E) than pre-treatment cultures and vehicle controls, and a higher LDH release into the medium than cultures before treatment (Fig. 6A), indicating a greater decrease in functionality and viability than that observed in co-cultured bronchial MucilAir cultures. Interestingly, increased ATP content was observed in monocultured bronchial MucilAir cultures treated with AFB1, similar to that seen in the co-cultured models (Fig. 6D).
Inhaled substances do not only have an influence on the lungs. Their potential biological impact also depends on an interplay with the other organs, especially the liver, which is a key metabolizer, transforming compounds into metabolites with new properties. We present here a HUMIMIC Chip3plus that combines a physiologically relevant 3D lung model previously used for assessment of aerosol toxicity40,41 with liver spheroids acting as a metabolizing compartment.
Oxygen pressure is important for differentiation and maintenance of cellular models, as it has been shown to modulate differentiation of both ciliated cells and hepatocytes42,43. Hence, we characterized partial pO2 in the Chip3plus. In the lung compartment, we found that atmospheric pO2 decreased to 100 hPa within 3 days when the compartment was closed with an airtight lid. As this value is below physiological levels (130 hPa in the alveoli to 153 hPa in the upper airways at sea level)31, the Chip3plus lung compartment was modified. Using a gas-permeable membrane as a lid helped stabilize the pO2 close to physiological levels. Moreover, the pO2 in the liver compartment was in the range of 40–87 hPa. Blood entering the periportal zone of a human liver sinusoid contains oxygen with a pO2 of 80–87 hPa44; by the time the blood leaves the pericentral zone, the pO2 would have decreased to 40–47 hPa44. Thus, the pO2 values recorded in the culture medium around the liver spheroids were in the range of in vivo pO2. Because of the large variations in pO2 values measured in the liver compartment, the existence of special gradients within the compartment can be presumed. Therefore, measurements performed at one location can only be considered as an estimate of the pO2 for the whole compartment. Measurement variability may result from the non-homogeneous spreading of liver spheroids when they were cultured, in accordance with our standard protocol, at the bottom of the culture compartment. The number of liver spheroids between the microfluidic channel transporting medium from the direction of the lung compartment and the oxygen sensor may influence the pO2 measured at the centrally located sensor. Lower pO2 measurements, therefore, would indicate more oxygen-consuming liver spheroids located before the sensor. The variability in pO2 measurements could be improved in the future by using the SpheroidBrick inlays for culturing liver spheroids in chips. These have been shown here to result in a defined and more homogeneous distribution of liver spheroids in the liver compartment. Moreover, the SpheroidBricks prevented the adhesion of liver spheroids to the glass surface of the chip. The future use of SpheroidBricks for other spheroid-based tissue models is envisioned to yield higher reproducibility and reliability in multi-organ studies. Similarly, the use of oxygen sensors is applicable to other MOC-based cultures and will result in a better understanding of culture conditions and tissue behaviour. Additionally, the use of floating sensor beads in future studies may allow for spatially resolved oxygen measurements within the chip.
The present study yielded a robust microfluidic chip-based co-culture of human bronchial tissue and liver spheroids maintained for 14 days in a standardized cell culture medium. Chips have been described previously that enabled 14- to 28-day bronchial and liver tissue co-cultures21,22. Our chip differs in many respects including size, pump mechanism, and material. Although the use of PDMS is controversial because of its ability to absorb hydrophobic substances45,46,47, it renders our chip compatible with tissue imaging by its transparency and enables more rapid prototyping. Hence, the HUMIMIC Chip platform can be easily adapted to other organ combinations or to the addition of organs such as the kidney to replicate absorption, distribution, metabolism, excretion, and toxicity testing of inhaled compounds. Although the liver model used here is a robust proxy for human hepatocytes, replacing the HepaRG cells with primary human hepatocytes would improve the model and better reflect the functions of a human liver, enabling the selection of specific genotypes for studying inhaled substances48. Furthermore, the integration of other relevant cell types into the 3D models, such as Kupffer cells into the liver model or fibroblasts into the MucilAir culture, would provide a more accurate simulation of the pathophysiological response to a substance49,50.
The functional coupling of lung and liver models was evaluated by exposing the co-culture to AFB1. Decreased functionality was shown exclusively for the bronchial MucilAir culture in chip-based monocultures. It is widely accepted that the carcinogenic and acute toxic responses to AFB1 are dependent on its metabolic activation35,36. The major metabolites formed in the liver are AFB1–8,9-epoxide, aflatoxin M1–8,9-epoxide, and aflatoxin Q151. Aflatoxin M1−8,9-epoxide and AFB1−8,9-epoxide have been shown to be cytotoxic, whereas aflatoxin Q1 is considered a detoxification product52,53,54. It is assumed that bioactivation in bronchial cells results exclusively in the production of cytotoxic metabolites38,55,56. We cannot conclude with absolute certainty that the AFB1 was metabolized because we did not assess the presence of metabolites in the chip microfluidics, and proof of activation-based AFB1 toxicity would require inhibition of all CYP enzymes in the tissues. Nonetheless, a protective decrease in AFB1 toxicity in the bronchial MucilAir culture by the metabolic capacity of the liver spheroids was shown following treatment with 5 µM AFB1. This finding demonstrates crosstalk in the new human lung–liver MOC system and reproduces the findings reported by Bovard et al.21, although the concentration of AFB1 for which an effect could be demonstrated was lower (5 µM vs. 100 µM). However, comparison of the data is difficult because of the different test conditions (e.g., composition and volume of cell culture medium). The use of other test substances will assist in evaluating the performance of the individual MOC platforms. In this regard, exposure of the lung tissue to an aerosol would be preferable for testing the MOC platform under a realistic exposure scenario. This will enable assessment of not only the toxicity but also the bioavailability of inhaled substances and could, therefore, become an important tool in drug discovery and personalized medicine.
Materials and Methods
Chip design and fabrication
A new design of the commercially available microphysiological HUMIMIC Chip platform14, Chip3plus, was developed to contain three consecutive culture compartments—one of a 96-well format and two of a 24-well format—thereby allowing an increase in the medium volume to up to 4 mL per circuit (Fig. 1A). In this study, the Chip3plus was used to co-culture one 24-well hanging Transwell insert-based bronchial MucilAir culture with 3D HepaRG-based liver spheroids (Fig. 1B). The device was fabricated as described by Wagner et al.9. Briefly, a PDMS layer of 2-mm height, containing the microfluidic channel, culture compartment openings, and micropump membranes, was cast against a polycarbonate adapter plate by replica moulding. The PDMS layer was then bonded to a microscopic glass slide by using low-pressure oxygen plasma, closing the channels at a height of 100 µm. A commercially produced batch of the Chip3plus was used for the experiments after passing quality control. Pulsatile fluid flow in the tissue-connecting circuit is driven by an on-chip micropump, modified after Wu and colleagues57. An external control unit (HUMIMIC Starter, TissUse GmbH) maintains a pulsatile flow in each circuit of the Chip3plus through alternating application of compressed air and vacuum to the pump membranes at a defined frequency. Each control unit can operate eight Chip3plus simultaneously. The on-chip peristaltic micropump was operated at a pumping frequency of 0.5 Hz and pressure of 50 kPa, enabling continuous pulsatile flow. At this frequency, the medium flow rate corresponded to 5.32 ± 1.46 µL/min. Microscopic inspection from the bottom of the Chip3plus permitted daily monitoring of tissue integrity.
Cell sources and maintenance
Differentiated HepaRG cells (lot HPR116259-TA08 or HPR116NS080003) were obtained from Biopredic International (Rennes, France). The HHSteCs were purchased from ScienCell (Carlsbad, CA, USA). Bronchial MucilAir cultures were purchased from Epithelix Sàrl and consisted of tissues from a non-smoking healthy man (41-year-old Caucasian; batch MD072001) or a non-smoking woman (59-year-old Caucasian; batch MD076801). The differentiated HepaRG cells were thawed and seeded 7 days before spheroid formation. Standard HepaRG culture medium consisted of Williams’ E medium (PAN-Biotech, Aidenbach, Germany) supplemented with 10% foetal calf serum (Corning Life Sciences, Tewksbury, MA, USA), 5 μg/mL human insulin (PAN-Biotech), 2 mM L-glutamine (Corning), 5 × 10−5 M hydrocortisone hemisuccinate (Sigma-Aldrich, St. Louis, MO, USA), and 1% penicillin/streptomycin (Corning). Dimethyl sulfoxide (0.5%; Carl Roth GmbH, Karlsruhe, Germany) was added to the medium to maintain the HepaRG cells in a differentiated state. The following day, the medium was renewed with HepaRG medium containing 2% dimethyl sulfoxide. The cells were maintained in this medium for 6 days until spheroid formation.
HHSteCs were expanded in stellate cell medium (ScienCell). The cells were used between passages 3 and 8. Pre-culture was commenced at least 2 days before spheroid formation.
Bronchial MucilAir cultures were received in 24-well plates, treated in accordance with the manufacturer’s protocol, and maintained in MucilAir maintenance medium (Epithelix) for 5–7 days before transfer to the Chip3plus. The medium was changed every 2–3 days, with visual inspection at each feeding to confirm tissue integrity and the presence of beating cilia.
Liver spheroid production
Human liver spheroids were formed by combining differentiated HepaRG cells and HHSteCs in 384-well spheroid microplates (Corning) in standard HepaRG culture medium, as described by Bauer et al.12, with minor modifications. Briefly, 50 μL of medium containing 24,000 hepatocytes and 1,000 HHSteCs were pipetted into each well of an ultra-low-attachment spheroid microplate (Corning). The plate was centrifuged for 2 min at 300 × g and incubated at 37 °C in 5% CO2. Liver spheroids without HHSteCs were thawed and formed directly after thawing in HepaRG culture medium. Compact spheroids formed within 3 days. Forty spheroids were collected in a 24-well ultra-low-attachment plate (Corning) in standard HepaRG culture medium. The plate was placed on a 3D rotator (PS-M3D; Grant Instruments, Royston, UK) for 1 day before the spheroids were used for the experiments.
Co-culture of a bronchial MucilAir culture and liver spheroids in the Chip3plus
The Chip3plus cultures were all cultivated in MucilAir maintenance medium. Forty liver spheroids were loaded into the 96-well culture compartment and cultured on glass or in a polyethylene glycol-based SpheroidBrick inlay purchased from Cellbricks. One bronchial MucilAir culture was transferred into the middle 24-well culture compartment. The third culture compartment of each circuit was used as a medium reservoir. An additional Chip3plus was loaded with one bronchial MucilAir culture only. The Chip3plus was filled with a total volume of 4 mL medium: 400 µL of medium was added below the bronchial MucilAir culture, 700 µL of medium was added to the liver culture compartment, and the culture compartment used as a medium reservoir was filled with 2.9 mL of medium. The lung culture compartment was then sealed with a special screw (Fig. 1A) containing a gas-permeable cellulose fibre based membrane (non-woven white Rayon, Corning). Half of the medium was replaced every 2–3 days. Cultivation ended after 14 days, and the organ equivalents were collected from the culture compartments.
On-line oxygen measurement with PreSens technology
D2 sensors were placed at the bottom of the chip during chip production directly after the bonding procedure to measure partial pO2 in the medium. D7 sensors were placed onto the inward-facing side of the lid for measurements in the air above the bronchial MucilAir culture. Gas-permeable membranes were used with D7 or D5 sensors. The pO2 at the measurement locations was determined from the other side of the glass slide, lid, or gas-permeable membrane by using a fluorescence spectrometer (PreSens Precision Sensing GmbH) connected to fibre optics and analysed by using the PreSens Measurement Studio 2 software. Two-point calibration was performed for each measurement condition, and linear regression was applied. Measurements of pO2 were conducted for up to 14 days at various locations inside each Chip3plus (including a blank chip without any tissues). The gas-permeable lid above the bronchial MucilAir cultures was replaced by a standard lid for some experiments.
Chip cultures were set up and maintained with MucilAir medium for 2 days to enable the tissues to adapt to the dynamic culturing. The medium was replaced entirely with MucilAir medium containing 5 µm AFB1 (VWR, Radnor, PA, USA) dissolved in 0.1% dimethyl sulfoxide in all three culture compartments for AFB1 exposure. The medium was replaced with MucilAir medium containing 0.1% dimethyl sulfoxide for the vehicle control. The tissue cultures were harvested for further analysis after 24 h of AFB1 treatment.
Analysis of medium samples
Medium samples were collected during the medium exchange every 24–72 h for albumin and LDH analysis. A commercially available ELISA kit was used to measure albumin concentrations (E80–129; Bethyl Laboratories, Montgomery, TX, USA). Absorption was determined by using the FLUOstar Omega microplate reader (BMG Labtech, Ortenberg, Germany) at 450 nm. LDH release into the medium was analysed by using the Indiko Plus analyser (Thermo Fisher Scientific, Waltham, MA, USA). Positive controls (maximum LDH release values) were generated by addition of 1% (v/v) Triton X-100 (VWR).
Measurement of transepithelial electrical resistance
Transepithelial electrical resistance in the bronchial MucilAir cultures was measured by using an STX-2 electrode connected to an EVOM2 epithelial volt/ohm meter (World Precision Instruments, Sarasota, FL, USA) in accordance with the manufacturer’s instructions. The value was multiplied by the surface of the inserts (0.33 cm2) to obtain the resistance value in the total area (ohm × cm2).
Measurement of ciliary beating frequency
Ciliary beating frequency was measured in bronchial MucilAir™ cultures on days 0 and 7 and at the end of the experiment. The cultures were placed on a heating plate pre-warmed to 37°C on an inverted phase-contrast microscope (Axio Ver. A1, Carl Zeiss, Oberkochen, Germany) equipped with a 10 × objective and connected to a high-speed digital video camera (acA1300, Basler AG, Ahrensburg, Germany). Ciliary beating frequency was recorded at 120 frames per second in short movies composed of 512 frames and analysed by using the SAVA analysis software (Ammons Engineering, Clio, MI, USA).
Liver spheroids from each culture were embedded in Tissue-Tek O.C.T. compound (Sakura Finetek, Torrance, CA, USA) and subsequently snap-frozen for immunohistochemical analysis. Representative central cryostat sections of the liver spheroids were stained with a combined TUNEL/Ki67 immunofluorescence stain to detect proliferating and apoptotic cells. The 8-µm sections were stained by using the Apo-Direct apoptosis detection kit (Thermo Fisher Scientific) in accordance with the manufacturer’s instructions. The slides were then blocked with 10% (v/v) goat serum in phosphate-buffered saline for 20 min, treated with primary mouse anti-human Ki67 antibody (Thermo Fisher Scientific, Clone 20Raj1) overnight, washed twice, and developed by goat anti-mouse CF594 (Biotium, Fremont, CA, USA) for 45 min. DAPI (Roche Diagnostics, Basel, Switzerland) was added for nucleus staining. Images were obtained by using a Keyence fluorescence microscope (Osaka, Japan).
ATP-based cell viability assay
The CellTiter-Glo 3D cell viability assay (Promega, Madison, WI, USA) was used to measure the total ATP content of the tissues. The bronchial MucilAir cultures were transferred to an empty 24-well plate, and 150 µL of CellTiter-Glo reagent was added on the apical side of the cultures. Single liver spheroids were collected in a 96-well clear-bottom white polystyrene microplate in 50 µL of medium, and 50 µL of CellTiter-Glo reagent was added. The plates were shaken vigorously for 5 min to induce cell lysis and then incubated for an additional 25 min at room temperature. Control wells containing culture medium without cells were prepared to obtain a value for background luminescence. Aliquots (50 µL) of each lysate were collected in a 96-well clear-bottom white polystyrene microplate for the bronchial MucilAir samples. Luminescence was measured by using the FLUOstar Omega microplate reader (BMG Labtech).
Statistical significance was tested by using the Brown–Forsythe and Welch ANOVA tests with the Dunnett’s T3 post-hoc test (ATP values) or mixed-effects analysis with Tukey’s post-hoc test in Prism v. 8.0 (GraphPad, La Jolla, CA, USA). p < 0.05 was considered statistically significant.
Viravaidya, K., Sin, A. & Shuler, M. L. Development of a microscale cell culture analog to probe naphthalene toxicity. Biotechnol. Prog. 20, 316–323 (2004).
Huh, D. A human breathing lung-on-a-chip. Ann. Am. Thorac. Soc. 12, S42–S44 (2015).
Ataç, B. et al. Skin and hair on-a-chip: in vitro skin models versus ex vivo tissue maintenance with dynamic perfusion. Lab Chip 13, 3555 (2013).
Schimek, K. et al. Integrating biological vasculature into a multi-organ-chip microsystem. Lab Chip 13, 3588 (2013).
Marx, U. et al. Biology-inspired microphysiological system approaches to solve the prediction dilemma of substance testing. ALTEX 33, 272–321 (2016).
Dehne, E.-M., Hasenberg, T. & Marx, U. The ascendance of microphysiological systems to solve the drug testing dilemma. Futur. Sci. OA FSO185 https://doi.org/10.4155/fsoa-2017-0002 (2017).
Lee, H. et al. A pumpless multi-organ-on-a-chip (MOC) combined with a pharmacokinetic-pharmacodynamic (PK-PD) model. Biotechnol. Bioeng. 114, 432–443 (2017).
Oleaga, C. et al. Multi-organ toxicity demonstration in a functional human in vitro system composed of four organs. Sci. Rep. 6, 20030 (2016).
Wagner, I. et al. A dynamic multi-organ-chip for long-term cultivation and substance testing proven by 3D human liver and skin tissue co-culture. Lab Chip 13, 3538 (2013).
Maschmeyer, I. et al. Chip-based human liver-intestine and liver-skin co-cultures - A first step toward systemic repeated dose substance testing in vitro. Eur. J. Pharm. Biopharm. 95, 77–87 (2015).
Materne, E. et al. A multi-organ-chip co-culture of human liver equivalents and neurospheres for long- term substance testing. 13355
Bauer, S. et al. Functional coupling of human pancreatic islets and liver spheroids on-a-chip: Towards a novel human ex vivo type 2 diabetes model. Sci. Rep. 7, 14620 (2017).
Maschmeyer, I. et al. A four-organ-chip for interconnected long-term co-culture of human intestine, liver, skin and kidney equivalents. Lab Chip 15, 2688–2699 (2015).
Hübner, J. et al. Simultaneous evaluation of anti-EGFR-induced tumour and adverse skin effects in a microfluidic human 3D co-culture model. Sci. Rep. 8, 1–12 (2018).
Karp, P. H. et al. An In Vitro Model of Differentiated Human Airway Epithelia: Methods for Establishing Primary Cultures. In Epithelial Cell Culture Protocols 115–137 https://doi.org/10.1385/1-59259-185-X:115 (Humana Press, 2002).
Leclercq, B. et al. Differential responses of healthy and chronic obstructive pulmonary diseased human bronchial epithelial cells repeatedly exposed to air pollution-derived PM 4. Environ. Pollut. 218, 1074–1088 (2016).
Huh, D. et al. Reconstituting organ-level lung functions on a chip. Science (80-.). 328, 1662–1668 (2010).
Benam, K. H. et al. Small airway-on-a-chip enables analysis of human lung inflammation and drug responses in vitro. Nat. Methods 13, 151–157 (2015).
Stucki, J. D. et al. Medium throughput breathing human primary cell alveolus-on-chip model. Sci. Rep. 8, 1–13 (2018).
Zanger, U. M. & Schwab, M. Cytochrome P450 enzymes in drug metabolism: Regulation of gene expression, enzyme activities, and impact of genetic variation. Pharmacol. Ther. 138, 103–141 (2013).
Bovard, D. et al. A lung/liver-on-a-chip platform for acute and chronic toxicity studies. Lab Chip https://doi.org/10.1039/C8LC01029C (2018).
Coppeta, J. R. et al. A portable and reconfigurable multi-organ platform for drug development with onboard microfluidic flow control. Lab Chip 17, 134–144 (2017).
Godoy, P. et al. Recent advances in 2D and 3D in vitro systems using primary hepatocytes, alternative hepatocyte sources and non-parenchymal liver cells and their use in investigating mechanisms of hepatotoxicity, cell signaling and ADME. in. Archives of toxicology 87, 1315–530 (2013).
Yokoyama, Y. et al. Comparison of Drug Metabolism and Its Related Hepatotoxic Effects in HepaRG, Cryopreserved Human Hepatocytes, and HepG2 Cell Cultures. Biol. Pharm. Bull. 41, 722–732 (2018).
Kanebratt, K. P. & Andersson, T. B. Evaluation of HepaRG Cells as an in Vitro Model for Human Drug Metabolism Studies. Drug Metab. Dispos. 36, 1444–1452 (2008).
McGill, M. R. et al. HepaRG cells: A human model to study mechanisms of acetaminophen hepatotoxicity. Hepatology 53, 974–982 (2011).
Gunness, P. et al. 3D organotypic cultures of human heparg cells: A tool for in vitro toxicity studies. Toxicol. Sci. 133, 67–78 (2013).
Takahashi, Y. et al. Three-dimensional (3D) spheroid cultures improve the metabolic gene expression profiles of HepaRG cells. Biosci. Rep. 1–7 https://doi.org/10.1042/BSR20150034 (2015).
Bell, C. C. et al. Characterization of primary human hepatocyte spheroids as a model system for drug-induced liver injury, liver function and disease. Sci. Rep. 6, 25187 (2016).
Markov, D. A., Lillie, E. M., Garbett, S. P. & McCawley, L. J. Variation in diffusion of gases through PDMS due to plasma surface treatment and storage conditions. Biomed. Microdevices 16, 91–96 (2014).
Silbernagl, S., Draguhn, A. & Despopoulos, A. Taschenatlas Physiologie. (Georg Thieme Verlag, 2018).
Lee, W. L. et al. Muco-ciliary transport: Effect of mucus viscosity, cilia beat frequency and cilia density. Comput. Fluids 49, 214–221 (2011).
Srinivasan, B. et al. TEER measurement techniques for in vitro barrier model systems. J. Lab. Autom. 20, 107–126 (2015).
Burd, J. F. & Usategui-Gomez, M. A colorimetric assay for serum lactate dehydrogenase. Clin. Chim. Acta 46, 223–227 (1973).
Ziglari, T. & Allameh, A. The Significance of Glutathione Conjugation in Aflatoxin Metabolism. In Aflatoxins - Recent Advances and Future Prospects i, 13 (InTech, 2013).
Neal, G. E. et al. Toxicology and Applied Pharmacology - Metabolism and Toxicity of Aflatoxins M1and B1in Human-Derivedin VitroSystems. 158, 152–158 (1998).
Kamdem, L. K., Meineke, I., Gödtel-Armbrust, U., Brockmöller, J. & Wojnowski, L. Dominant contribution of P450 3A4 to the hepatic carcinogenic activation of aflatoxin B1. Chem. Res. Toxicol. 19, 577–586 (2006).
Vleet, T. R. V., Klein, P. J. & Coulombe, R. A. Metabolism of aflatoxin b 1 by normal human bronchial epithelial cells. 1997, 525–540 (2001).
Ramaiahgari, S. C. et al. Three-dimensional (3D) HepaRG spheroid model with physiologically relevant xenobiotic metabolism competence and hepatocyte functionality for liver toxicity screening. Toxicol. Sci. 159, 124–136 (2017).
Hoffmann, W. et al. Establishment of a Human 3D Tissue-Based Assay for Upper Respiratory Tract Absorption. Appl. Vitr. Toxicol. 4, 139–148 (2018).
Iskandar, A. R. et al. A systems toxicology approach for comparative assessment: Biological impact of an aerosol from a candidate modified-risk tobacco product and cigarette smoke on human organotypic bronchial epithelial cultures. Toxicol. Vitr. 39, 29–51 (2017).
Gerovac, B. J. et al. Submersion and Hypoxia Inhibit Ciliated Cell Differentiation in a Notch-Dependent Manner. Am. J. Respir. Cell Mol. Biol. 51, 516–525 (2014).
Guo, R., Xu, X., Lu, Y. & Xie, X. Physiological oxygen tension reduces hepatocyte dedifferentiation in in vitro culture. Sci. Rep. 7, 5923 (2017).
Kietzmann, T. Metabolic zonation of the liver: The oxygen gradient revisited. Redox Biol. 11, 622–630 (2017).
Toepke, M. W. & Beebe, D. J. PDMS absorption of small molecules and consequences in microfluidic applications. Lab Chip 6, 1484 (2006).
Wang, J. D., Douville, N. J., Takayama, S. & Elsayed, M. Quantitative analysis of molecular absorption into PDMS microfluidic channels. Ann. Biomed. Eng. 40, 1862–1873 (2012).
Nianzhen, L., Schwartz, M. & Ionescu-Zanetti, C. PDMS Compound Adsorption in Context. J. Biomol. Screen. 14, 194–202 (2009).
Hart, S. N. et al. A comparison of whole genome gene expression profiles of HepaRG cells and HepG2 cells to primary human hepatocytes and human liver tissues. Drug Metab. Dispos. 38, 988–994 (2010).
Kolios, G., Valatas, V. & Kouroumalis, E. Role of Kupffer cells in the pathogenesis of liver disease. World J. Gastroenterol. 12, 7413–20 (2006).
Marrazzo, P. et al. 3D reconstruction of the human airway mucosa in vitro as an experimental model to study NTHi infections. PLoS One 11, 1–15 (2016).
Dohnal, V., Wu, Q. & Kuča, K. Metabolism of aflatoxins: Key enzymes and interindividual as well as interspecies differences. Arch. Toxicol. 88, 1635–1644 (2014).
Palanee, T., Dutton, M. F. & Chuturgoon, A. A. Cytotoxicity of aflatoxin B1 and its chemically synthesised epoxide derivative on the A549 human epithelioid lung cell line. Mycopathologia 151, 155–9 (2001).
Bujons, J., Hsieh, D. P., Kado, N. Y. & Messeguer, A. Aflatoxin M1 8,9-epoxide: preparation and mutagenic activity. Chem. Res. Toxicol. 8, 328–32
Hsieh, D. P. H., Salhab, A. S., Wong, J. J. & Yang, S. L. Toxicity of aflatoxin Q1 as evaluated with the chicken embryo and bacterial auxotrophs. Toxicol. Appl. Pharmacol. 30, 237–242 (1974).
Van Vleet, T. R., Coulombe, R. A. & Mace, K. Comparative aflatoxin B1 activation and cytotoxicity in human bronchial cells expressing cytochromes P450 1A2 and 3A4. Cancer Res. 62, 105–112 (2002).
He, X.-Y. et al. Efficient activation of aflatoxin B1 by cytochrome P450 2A13, an enzyme predominantly expressed in human respiratory tract. Int. J. Cancer 118, 2665–2671 (2006).
Wu, M.-H., Huang, S.-B., Cui, Z., Cui, Z. & Lee, G.-B. A high throughput perfusion-based microbioreactor platform integrated with pneumatic micropumps for three-dimensional cell culture. Biomed. Microdevices 10, 309–319 (2008).
We gratefully acknowledge Philip Saunders and Edanz Editing for critical editing of the article, Sindhoora Bhargavi Gopala Reddy (from PMI) for the excellent manuscript review and Cellbricks for developing the SpheroidBricks.
U.M. is the founder, shareholder, and CEO of TissUse GmbH, which produces and markets microphysiological systems. S.F., K.L., D.B. and J.H. are employees of Philip Morris International.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Schimek, K., Frentzel, S., Luettich, K. et al. Human multi-organ chip co-culture of bronchial lung culture and liver spheroids for substance exposure studies. Sci Rep 10, 7865 (2020). https://doi.org/10.1038/s41598-020-64219-6
Stem Cell Research & Therapy (2021)
Biologia Futura: the importance of 3D organoids—a new approach for research on neurological and rare diseases
Biologia Futura (2021)