Performance of wild-Serbian Ganoderma lucidum mycelium in treating synthetic sewage loading using batch bioreactor

The fluctuation of domestic wastewater characteristic inhibits the current conventional microbial-based treatment. The bioremediation fungi has received attention and reported to be an effective alternative to treat industrial wastewater. Similar efficient performance is envisaged for domestic wastewater whereby assessed performance of fungi for varying carbon-to-nitrogen ratios in domestic wastewater is crucial. Thus, the performance of pre-grown wild-Serbian Ganoderma lucidum mycelial pellets (GLMPs) was evaluated on four different synthetic domestic wastewaters under different conditions of initial pH (pH 4, 5, and 7) and chemical oxygen demand (COD) to nitrogen (COD/N) ratio of 3.6:1, 7.1:1, 14.2:1, and 17.8:1 (C3.6N1, C7.1N1, C14.2N1, and C17.8N1). The COD/N ratios with a constant concentration of ammonia–nitrogen (NH3–N) were chosen on the basis of the urban domestic wastewater characteristics sampled at the inlet basin of a sewage treatment plant (STP). The parameters of pH, COD, and NH3–N were measured periodically during the experiment. The wild-Serbian GLMPs efficiently removed the pollutants from the synthetic sewage. The COD/N ratio of C17.8N1 wastewater had the best COD and NH3–N removal, as compared to the lower COD/N ratio, and the shortest treatment time was obtained in an acidic environment at pH 4. The highest percentage for COD and NH3–N removal achieved was 96.0% and 93.2%, respectively. The results proved that the mycelium of GLMP has high potential in treating domestic wastewater, particularly at high organic content as a naturally sustainable bioremediation system.

Performance of fungi at initial pH of 7. The preliminary study of GLMP was conducted using the influent synthetic wastewater at the pH of 7.2 to 7.5, set at the mean pH value of the real sewage pH range, often measured to be between 6.5 and 8.5. In general, the results showed that the fungi successfully removed the pollutants from the synthetic wastewater and that the trends of pollutant removal were similar for all the tested COD/N ratios. The data shown in Fig. 1(C) indicate that within the first 12 h of treatment, the pH of the synthetic wastewater was maintained at its initial value, whereas the concentration of both COD and NH 3 -N ( Fig. 1(A,B), respectively) showed a slightly increasing pattern.
The increasing pollutant concentration was believed to be influenced by the residual from the fungi growth medium during the pre-culturing process. The inoculum was pre-grown mycelial biomass for 10 days (stationary) fermentation whereas it is in the most active state. Yeast extract (1 g/L), Glucose (30 g/L), salts, and Ammonium chloride (source of Nitrogen, NH4Cl, 4 g/L) were the initial media used 19 and has caused higher initial concentration of COD and nitrogen compounds. After 10 days, fungal residue has been detected by COD analysis due to catabolite repression or so-called "glucose effect 20 " which may give high pollutant concentration during the first hours of treatment at pH7.Beside that, the fungi can grow at initial hour as it consumed the pollutants as their carbon source, after the first hour the growth stopped due to unfavourable fungal growth conditions such as pH (G. lucidum grow best at pH 4 19,21 ), cocktails of bacteria in the wastewater competing the same nutrients 22 , and natural G. lucidum survivability which caused pellet autolysis (cell death and cryptic growth) 23 and samples were not 100% homogenous which lead to higher COD values in the initial treatment time.
After 24 h of treatment, the pH of the wastewater decreased for all the tested influents. The decreasing pH value was consistent with the increasing percentage removal of COD and NH 3 -N. The highest pollutant removal achieved followed the order of C17.8N1 > C14.2N1 > C7.1N1 > C3.6N1. In the case of the high COD/N ratio of C17.8N1, the percentage of COD and NH 3 -N removed was 40.3% and 62.7%, respectively, which was achieved after 24 h at a pH value of 3.24. The optimum condition was achieved at treatment time of 72 h with 93.8% and 93.2% of COD and NH 3 -N removal, respectively, at pH 3.28. After 72 h, the pH remained at 3.28, and the percentage removal of the pollutant showed no significant changes in COD over the next 48 h of treatment with 94.1% and 93.9% removal at 96 h and 120 h, respectively. However, the opposite trend was observed for ammonia where the performance of ammonia removal dropped to 86.4% at 96 h before continuously decreasing to 76.2% at 120 h. The decrease in the performance of ammonia removal was attributed to the cell death caused by the accumulation of metabolic waste 15 .
After a day, with the pH value at 4.82, the low COD/N ratio of C3.6N1 recorded a low percentage of COD removal with 18.4% of the organic content removed; however, a slightly higher NH 3 -N ammonia removal was observed (i.e. 33.9%). After three days, the pH was only reduced to 4.18, which was less than that in the case of the high COD/N ratio (C17.8N1) with a pH value of 3.28, and the performance of the fungi was not as expected as only 61.4% of COD and 53.6% of NH 3 -N were removed. The medium COD/N ratio of COD 213 (C7.1N1) and COD 427 (C14.2N1) showed moderate percentages of removal. For wastewater with C7.1N1, 23.0% COD removal and 42.1% NH 3 -N removal were recorded at pH 4.70 after 24 h. In contrast, an almost similar efficiency was observed for the C14.2N1 flask with 35.3% of COD and 36.5% of NH 3 -N removed at pH 4.25. However, when the treatment time was increased to 72 h, the treatment efficiency increased to the highest value of 88.5% COD removal and 56.1% NH 3 -N removal for C7.1N1 and 90.0% COD removal and 80.8% NH 3 -N removal for C14.2N1. Note that the pH value was logged at 3.65 and 3.32 for C7.1N1 and C14.2N1, respectively.
The data indicated that although fungi have the potential to treat organic and ammonia at the commonly measured pH of sewage, the treatment time required is rather long, reaching up to 48 h for all the COD/N ratios. GLMP took time to acclimatise to the ambient surroundings and only started to be efficient after 24 h, when the pH gradually decreased to below 4. This is quite consistent with the findings of a previous study on the removal of humic acid (monitored by colour reduction) 12 , wherein the acclimatisation of fungi T. versicolor was about 2 days and most of the colour was removed after 8 days. In another study, 24 h was needed for P. chrysosporium to be effective in removing phenol from synthetic oil refinery wastewater 24 . From here, fungi was adjusted the environmental pH for the fungi to utilised the pollutant and lead to a reduction in the pollutant concentration. The acidic environment obviously favoured the fungi 25 , who reported that effective fungal treatment was found within the pH range of 4.5. www.nature.com/scientificreports www.nature.com/scientificreports/ Performance of fungi at initial pH of 5. Previous experiments (with initial pH of 7) have shown that GLMP took approximately 48 h to stabilise and acclimatise. To further investigate the ability of GLMP to self-modify its environmental pH and a possible reduction of treatment time, the initial pH of 5 in the reactor was introduced to the GLMP. The changes in the pH values within the reactor with an initial pH of 5 are plotted in Fig. 2(C). In general, the pH is visibly consistent from the kick-off until t = 6 h before it started to decrease between 4.77 and 4.13 at t = 12 h. During the acclimatisation period, the COD concentration increased (which describes the negative COD reduction in Fig. 2(A)) due to as previously discussed. However, the concentration of NH 3 -N remained consistent throughout the acclimatisation period for all the COD/N ratios ( Fig. 2(B)). The data visibly showed that there was a time lag when the GLMP started to degrade NH 3 -N (with a notable exception of the highest COD/N ratio).
After 12 h of treatment, the pH started to decrease for all the considered ranges of the COD/N ratio discussed in this study. Corresponding to the decreasing pH at t = 24 h, the percentage removal of COD began to hit positive numbers. The decreasing trend of pH was consistent with the increasing percentage removal of COD and NH 3 -N. Similar findings (to those of the pH 7 experiments) were obtained where the highest pollutant removal was achieved for the reactor with the highest COD/N ratio (C17.8N1) and was sequentially followed by those for C14.2N1, C7.1N1, and C3.6N1. In the case of the highest COD/N ratio of C17.8N1, the percentages of COD removal and NH 3 -N removal were 15.3% and 37.3%, respectively, after 24 h of treatment at the recorded pH of 3.13. The maximum reduction was achieved at t = 48 h with 91.0% and 61.1% removal of COD and NH 3 -N, respectively at a much lower pH value of 2.47. After 48 h, the percentage removal of the pollutants reached its maximum potential with a steady pattern over the next 72 h of the treatment (88.6% COD removal and 61.0% NH 3 -N removal at 72 h, 89.1% COD removal and 64.4% NH 3 -N removal at 96 h, and 89.6% COD removal and 61.0% NH 3 -N removal at 120 h). www.nature.com/scientificreports www.nature.com/scientificreports/ In contrast, the lowest COD/N ratio (C3.6N1) recorded 57.0% and 17.7% of COD and NH 3 -N removal, respectively, at t = 24 h with a measured pH of 3.33. On the basis of these data, the COD reduction followed a consistent pattern rather early after 24 h of treatment (with a maximum value of 67.0% at the end of the experiment). The removal of NH 3 -N was evidently lower than that at the other COD/N ratios and only reached a maximum value of 29.0% at t = 48 h. The medium wastewater strength of COD 200 mg/L (C7.1N1) and COD 400 mg/L (C14.2N1) showed a moderate percentage removal, particularly for NH 3 -N. After 24 h of treatment, 40.6% of COD and 11.9% of NH 3 -N were removed for C7.1N1, while a much lower percentage of 2.0% and 8.2% for COD and NH 3 -N removal, respectively, was observed for C14.2N1. Both the reactors recorded decreasing pH values within the range of 3.41 to 3.60 when increasing treatment time to 72 h increased the percentage of COD removal, where both the medium wastewater strengths recorded 87.9% and 89.7% for C7.1N1 and C14.2N1, respectively. Note that the C14.2N1 reactor produced 89.36% removal at t = 48 h, much earlier than when the C7.1N1 reactor had a lower percentage of removal (at t = 72 h).
The percentage of NH 3 -N removal was only 40.7% and 70.5% for C7.1N1 and C14.2N1, respectively, even though the pH was significantly reduced even to less than 3 (at 2.6) at t = 48 h. In this pH 2 environment, the fungi were believed to be in a non-detected growth activity phase 26 . In general, the potential of GLMP to reduce the NH 3 -N concentration was visibly much lower than that in the experiments with initial pH 7 for all the COD/N ratios. In the first 24 h of treatment, the percentage of removal was low, probably because the surrounding pH in the reactor was yet to achieve its desired optimum value.
Performance of fungi at initial pH of 4. Another experiment was conducted to investigate the effect of the initial pH on the performance of GLMP at the lowest pH value of 4. We acknowledged that a more acidic environment at pH 4 was completely undesirable for possible large-scale applications, but we wanted to investigate the possibility of reducing the treatment time if the initial pH in the reactor was similar to the optimised pH of the GLMP growth. Our hypothesis, however, was proven to be inaccurate, as the GLMP still required 12 h to acclimatise with a visible reduction only observed at t = 24 h.
The recorded monitoring pH in the reactor is shown in Fig. 3(C), with a slight increase in pH visible at t = 6 h, before it started to decrease to the range of 3.29 to 3.47 at t = 24 h. After 12 h of treatment, a fast decrease in the pH value was observed for all the COD/N ratios discussed in this study. The initial pH of 4 provided an acidic environment to the fungi to adapt to, and their response to induce the changes to a preferred pH value was much faster than that of pH 7. The rapid decrease in pH was consistent with the fast increasing percentage removal of COD and NH 3 -N. At the end of the experiment at t = 48 h, the lowest pH was measured for the C17.8N1 reactor, and the highest was for C3.6N1. Note that the duration of the experiment was shortened to 48 h, as the pH value was below 3. The rapid decrease in pH was consistent with the fast increasing percentage removal of COD and NH 3 -N.
The initial pH for the treatment obviously played no important role in accelerating the GLMP reaching its phase for the fungi to intake the pollutants. Interestingly here, the lowest COD/N ratio reactors improved its capability of reducing COD up to 79.7% and 88.2% for C7.1N1 and C3.6N1, respectively, at t = 48 h, as shown in Fig. 3(A). A significant increase in the COD removal was observed within 36 h of treatment for all the reactors. The trend in this experimental setup differed from that in the profile shown in the previous initial pH experiments, where a fast organic removal with 68.87% and 66.97% for the C3.6N1 and C7.1N1 reactors, respectively, was visible after 24 h of treatment, much faster than that in the case of the higher COD/N ratio wastewaters. However, both C3.6N1 and C7.1N1 were not able to achieve a similar percentage removal as shown in the C17.8N1 and C14.2N1 reactors at the end of the experiment at 96.0% and 94.1%, respectively. Interestingly, the reduction of NH 3 -N followed suit with the highest percentage recorded at 92.4% for C17.8N1 (Fig. 3(B)). According to the results obtained in the pH 7 and 5 experiments, the highest COD/N ratio (at C17.8N1) showed the most efficient percentage pollutant removal and was the fastest the considered COD/N ratios. High COD/N ratios in the wastewater can be considered mimicking the ligninolytic conditions (representing the real condition as wood has high C/N ratio). This scenario leads to increasing fungal production of lignin modifying enzymes 10,27 and consequently increased the consumption of nutrient. In this experiment, high percentage of ammonia removal by the fungal pellets was observed.
Although an excellent removal of COD was observed for the C3.6N1 and C7.1N1 reactors, a contrasting profile of the NH 3 -N reduction was noticed. After 24 h of treatment, only 16.4% and 24.2% of NH 3 -N removal were calculated for C3.6N1 and C7.1N1, respectively, even though the pH in these reactors fell into the range of 3.29 to 3.47. A rather disappointing final NH 3 -N reduction was obtained for both the reactors where only 25.3% and 39.1% of the removal was achieved for C3.6N1 and C7.1N1, respectively. The medium COD/N ratio of C14.2N1 showed a better percentage removal where after 24 h: 40.6% COD removal and 25.1% NH 3 -N removal. Although the COD removal may be within the same range as that of the C17.8N1 reactor, the C14.2N1 wastewater achieved a much lower NH 3 -N reduction at 70.9%.
Although the performance of GLMP in reducing COD and NH 3 -N varied and can be considered carbon-dependent, the huge potential of utilising GLMP even at low wastewater strength (i.e. a low COD/N ratio) was predicted. Based on the results of the highest percentage of both COD and NH 3 -N removal with the shortest treatment time, the best condition of GLMP-based wastewater treatment was high COD at an initial pH of 4. The best condition of pH 4 in the pure culture of GLMP is comparable to the findings by Xu et al. 15 which discussing the application of mixed algal-fungal strain (palletisation between C. vulgaris and G. lucidum 5.765) to treat synthetic domestic wastewater with different C/N ratio influents. The experiment was presented as low (100 mg/L), medium (200 mg/L), and high (400 mg/L) levels of COD (where the TN/TP level was fixed at medium strength). Wastewater strength at corresponding C/N ratios of C2.5N1-COD100, C5N1-COD200 and C10N1-COD400 was tested in a photobioreactor, set up in batch experiment for a much longer treatment time at 10 days.
The optimal condition achieved for the algal-fungal culture was for the C/N ratio C5N1 with a percentage removal for COD and total nitrogen (TN) of 74.41% and 79.35%. With respect to the C/N ratio, the C2.5N1 and C10N1 treatments had a significantly lower percentage removal with COD (74.79%) and TN (75.08%) for C2.5N1 and COD (71.60%) and TN (75.54%) for C10N1. The optimal pollution removal efficiency was achieved for treatment using the algal-fungal culture on day 8 with the pH of the synthetic wastewater consistent with the pH in the influent with the range of 6.0-7.5. The pure culture of G. lucidum showed advantages in the self-immobilisation of the pellet system and the long-activity maintenance of the secretion of bioactive metabolites 28 .
Our experimental work indicated that the culture of G. lucidum in the treatment of synthetic wastewater had a higher potential than the mixed culture. The pre-culture of the preparation of mycelium pellets for the pure fungus required 9-11 days as compared to the culturing condition for the algal-fungal culture, which required 14 days. Moreover, a higher percentage removal of organic pollutants, particularly COD, of about 96.0% was achieved as compared to 74.4% for the mix culture condition. The treatment with the pure culture of G. lucidum also had a short treatment time: under the optimal condition, the same results were achieved at 48 h of treatment under the initial acidic condition as those achieved after 8 days under the algal-fungal culture condition.

Morphological observation.
Like any other medicinal mushrooms, the Ganoderma species feed by the absorption of nutrients from their growth surroundings, such as synthetic nitrogen (N) 23 , ammonia nitrogen (NH 3 -N) 29 , atmospheric N 30 , and industrial dyes 31 . In a wastewater treatment application, adsorption has long been used for NH 3 -N removal 32 using costly non-biological materials, and is insufficient to meet the current www.nature.com/scientificreports www.nature.com/scientificreports/ market demand. The use of biological materials such as medicinal mushrooms offers a better alternative as the fungal source can be produced in bulk, using a cheap and safe process, and to a consistent quality 33 .
In the current study, the morphological verification of the wastewater-GLMP interaction was performed using a light microscope (LM) and a variable pressure scanning electron microscope (VPSEM) to evaluate the fungal adsorption on the NH 3 -N contaminants (Fig. 4). GLMP showed NH 3 -N absorption in an increasing COD/N gradient manner (C3.6N1; C7.1N1; C14.2N1 and C17.8N1) as compared to the untreated GLMP (transparent mycelial pellet: green arrow: Fig. 4(A)), which corresponded to an increasing grey-pellet coloration ( Fig. 4(B)-6(E): purple arrows). In Fig. 4(A), GLMP has an undisrupted (green arrow in LM; smooth pellet surface for VPSEM) spherical shape of the intertwined hyphae (indicating healthy pellets), which is in agreement with the findings of Espinosa-Ortiz et al. 34 and Veiter et al. 35 , and the SEM mycelial surface of the medicinal mushroom Coriolus versicolor 36 .
Although the GLMP retained its spherical shapes and oval masses after the treatment, changes on the hairy hyphae were much more visible in the LM and in the craters in the VPSEM (indicating unhealthy pellets with longer protuberances), as stated by Wan-Mohtar et al. 23 , due to the fungal autolysis possibly indicating NH 3 -N adsorption. For the treated GLMP, the blue arrow (craters) shows the pollutant deposited on the pellet surfaces; this bowl-shaped depression shows the balance residual ammonia deposited on the fungal pellet. There was not much difference in the pellet morphology between the low COD/N and the high COD/N ratios; however, Fig. 4 (C17.8N1) shows the highest grey-pellet coloration. Together, the morphological observations revealed that GLMP successfully adsorbed NH 3 -N in the tested synthetic wastewater.

conclusion
The wild-Serbian G. lucidum strain BGF4A1 (GLSB) had the potential to remove pollutants from the synthetic domestic wastewater. Among all of the tested parameters, the highest carbon to nitrogen (COD/N) ratio showed the best result with a percentage removal of COD and NH 3 -N of 96.0% and 93.2% respectively. This experiment also proved that the fungi worked efficiently under a favourable pH condition, which was in the acidic environment within a pH range of 2.5 to 3.5, consistent with the literature study. The results for the synthetic wastewater revealed the preliminary potential of wild-Serbian GLMPs in treating domestic wastewater, and further studies are necessary on the effect of this fungus on the treatment of real domestic wastewater in order to fully adapt the medicinal mushroom to real-world applications.

Materials and Methods
Domestic wastewater characteristics. The temporal characteristics of influent urban Malaysian domestic wastewater into STP with the population equivalent (PE) of 60000 were studied 37,38 . The wastewater was collected using the autosampler ISCO 3700 at intervals of 1 h, where each sampling campaign lasted 24 h. Note that 300 mL of each sample was filled into polyethylene bottles pre-preserved with 0.3 mL of 50% sulphuric acid (H 2 SO 4 ) 39 during each interval and was immediately brought to the laboratory after the sampling collection. The samples were transferred into 50-mL sterile centrifuge tubes, stored in a refrigerator (at 4 °C) until the analysis. The data collection was conducted in the year 2018, and the wastewater was consistently sampled on weekdays between April and August in the inter-monsoon season and at the start of the Northeast monsoon. Figure 5 shows the mean temporal concentration for COD and NH 3 -N. The data evidently show that the organic content in the incoming wastewater fluctuated over the 24-h period. The COD concentration showed a trend with two distinct peaks where the highest concentration was observed either early morning between 8:00 am to 9:00 am or early night around 8:00 pm. The range of COD concentration was between 117 mg/L and 612 mg/L. The early morning peak had a considerably higher concentration, ranging between 50 and 100 mg/L more than the evening peak. The lowest COD concentration was found late at night between around 0:00 am and 5:00 am. In contrast, when compared with the temporal pattern of the NH 3 -N concentration, the trend for ammonia was somewhat irregular with no common feature observed, except a slightly higher concentration early in the morning around 7:00 am to 10:00 am. The highest and the lowest NH 3 -N concentrations were 49 mg/L and 17.0 mg/L, respectively. The mean temporal concentration for NH 3 -N showed that the concentration did not fluctuate as much as the organic content. Thus, the main parameter that influenced the fluctuating COD/N ratio was the COD concentration.
Fungal culture and mycelial pellet cultivation. The wild-Serbian medicinal mushroom Ganoderma lucidum strain BGF4A1 (GLSB) stock culture was obtained from University of Belgrade, Serbia. The mushroom was isolated from the mountain of Avala (511 m above the sea level) located 16 km southeast of downtown Belgrade City. It was sub-cultured onto a potato dextrose agar (PDA, Sigma-Aldrich, Dorset, UK) slant, incubated at 28 °C for 7 days, and then, stored at 4 °C to avoid any contamination and to maintain its viability. The composition of the medium in grams per litre was as follows: Glucose 10, Yeast Extract (YE) 1, KH 2 PO 4 (mono-potassium  www.nature.com/scientificreports www.nature.com/scientificreports/ phosphate) 0.5, K 2 HPO 4 (di-potassium phosphate) 0.5, MgSO 4 (magnesium sulphate) 0.5, and NH 4 Cl (ammonium chloride) 4, unless otherwise stated. The isolation process was conducted based on the procedure optimised by Hassan et al. 19 .
Two seed culture stages were involved in the inoculum preparation of GLSB. Mycelial agar squares (5 mm × 5 mm) were extracted using a sterile scalpel from a 10-day-old plate and inoculated in a 250-mL Erlenmeyer flask containing 100 mL of the optimised medium solution (first seed culture). To produce additional growing hyphae tips, mycelium from the first seed culture were homogenised aseptically by using a hand blender for 10 s. This process was performed under a laminar flow, and then, 20% (20 mL) of the homogenised inoculum for the second seed culture was transferred into a 500-mL Erlenmeyer flask containing 200 mL of the medium. Throughout the process, the inoculum was inoculated into the fresh medium during the late exponential phase (from day 9 to day 11), as the cells were biochemically in their most agile and vital physiological state in this phase. The fungal culture was cultivated for 11 days at 25 °C and 100 rpm with the initial pH of 5, according to the optimum procedures suggested by Lai et al. 40 , Supramani et al. 21 , and Wan-Mohtar et al. 33 .
Experimental set-up of batch bioreactor for wastewater treatment. Four 1000-mL reactors were filled with 800 mL of synthetic domestic wastewater as per the set-up shown in Fig. 6. The medium of synthetic wastewater was prepared per 1000 mL volume for the following compounds: 100, 200, 400, and 500 mg of glucose, 73 mg of NH 4 Cl (ammonium chloride), 15 mg of Na 2 HPO 4 (disodium phosphate), 1.5 mg of KH 2 PO 4 (di-potassium phosphate), 4 mg of CaCl 2 (calcium chloride), and 2 mg of MgSO 4 .7H 2 O (magnesium sulphate heptahydrate). The same amount of pre-grown wild-Serbian GLMP with an estimated working volume of about 0.1% was inoculated with a sterile pipette into the filled synthetic wastewater at room temperature (approximately 25 °C) in the reactor. The reactor was constantly supplied with 3 L/min of air, creating an aerobic condition and homogenisation to avoid fungal cementation at the reactor wall, because it was run under a static condition with no agitation (Fig. 6). The treatment time for the first cycle was set to 120 h, before being varied for subsequent experiments on the basis of the performance of the organic and ammonia reduction of each cycle.
The experiments consistently used the same synthetic wastewater, prepared according to the modified recipe 15 to create similar conditions in all the experiments. On the basis of the measured COD shown in Fig. 5, different COD concentrations were prepared to represent the variability in the organic loading, denoted as low (107 mg/L), medium (213 mg/L and 427 mg/L), and high (534 mg/L) with a fixed amount of NH 3 -N of 30 mg/L. The reactors were prepared in duplicates. Theoretically, the COD value corresponds to the concentration of glucose, with 1.067 mg/L COD is equivalent to 1.000 mg/L glucose and the variation of COD allows for a systematic investigation of the influence of COD/N ratios ranging from C3.6N1, C7.1N1, C14.2N1, and C17.8N1. As domestic wastewater is commonly measured at pH 7 41 , whereas fungi are known to be most efficient at pH 4 42,43 , this study investigated the effect of the initial pH of 7, 5, and 4. The pH of wastewater was adjusted by adding 0.1-M HCl to the synthetic wastewater until the desired pH was achieved. Table 1 shows the influent values for all the tested parameters.
Sampling and analytical analysis. Throughout the experiment, the daily monitoring values of temperature and pH (using the pH meter, Eutech pH300) were recorded. In the first 24 h of treatment, the wastewater was frequently sampled to investigate the outset reaction of fungi towards the synthetic wastewater as per the set interval specified in Table 2. After 24 h, samples were extracted every 24 h (i.e. on a daily basis). By using a clean pipette, we extracted 15 mL of the liquid during sampling. All the samples were filtered using the Whatman filter paper Cellulose Nitrate Membrane Filters 0.45 µM prior to the analysis to remove the suspended mycelium. The filtered wastewater was then analysed for COD and NH 3 -N. The concentration of COD was estimated by closed  www.nature.com/scientificreports www.nature.com/scientificreports/ reflux, a colorimetric method using HACH vial high-range reactor digestion method (20-1500 mg/L) using the standard protocol from the manufacturer (Method 8000). Meanwhile, NH 3 -N concentrations were measured using HACH nitrogen, ammonia Test 'N Tube vials salicylate method high range (0.4-50.0 mg/L) using the standard protocol from the manufacturer (Method 10031). Both the methods were viewed using the UV spectrophotometer HACH DR6000. All the analysis was carried out in triplicates and the respective mean ± S.D represented in the graph is shown as error bars. It is noted that those error bars that are not visible in the graph are believed due to their symbols are much smaller than the size of the (data). Once the treatment is completed, the fungi were removed from the system through filtration and became another fungal biomass. The wild-Serbian G. lucidum, just like any other mushrooms, is the most efficient natural decomposers for organic matter and it can be applied into food and biomass chain 44 . The filtrates can be reusable into value-added biomass and incorporated as rich food-protein resources in landless food production concept 45 for circular food chains. In addition, fungal biomass has been applied as animal feed ingredients; Shiitake mushroom-Rainbow trout 46 , fingerlings of Carps-Shiitake mushroom 47 , shiitake mushroom-chicken 48 . GLMP observation under scanning electron microscope. The morphology details of the fungi were assessed under a light microscope (Labomed Lx 400) (LABOMED (USA)) connected to a digital camera (iVu 1500) and a Variable Pressure Scanning Electron Microscope (VPSEM) analysis (CARL ZEISS EVO MA 10 (UK) with EDAX APOLLO X (USA)). The fungi before and after treatment with synthetic wastewater were dried in a dehydrator at 35 °C for 2 h to strictly ensure that there was no water in the sample prior to the analysis. The microscopic and VPSEM analysis images for different fungal pellets before and after the treatment with the synthetic wastewater used in the experiments were then compared.