Structural determination of Enzyme-Graphene Nanocomposite Sensor Material

State-of-the-art ultra-sensitive blood glucose-monitoring biosensors, based on glucose oxidase (GOx) covalently linked to a single layer graphene (SLG), will be a valuable next generation diagnostic tool for personal glycemic level management. We report here our observations of sensor matrix structure obtained using a multi-physics approach towards analysis of small-angle neutron scattering (SANS) on graphene-based biosensor functionalized with GOx under different pH conditions for various hierarchical GOx assemblies within SLG. We developed a methodology to separately extract the average shape of GOx molecules within the hierarchical assemblies. The modeling is able to resolve differences in the average GOx dimer structure and shows that treatment under different pH conditions lead to differences within the GOx at the dimer contact region with SLG. The coupling of different analysis methods and modeling approaches we developed in this study provides a universal approach to obtain detailed structural quantifications, for establishing robust structure-property relationships. This is an essential step to obtain an insight into the structure and function of the GOx-SLG interface for optimizing sensor performance.

The graphene-based sensors are expected to aid direct and effective electron transfers by eliminating the use of redox mediators and oxidation overpotential [5][6][7][8] . Graphene, a two dimensional single-atom-thick crystalline nanomaterial, has engaged a wide range of markets due to its superlative qualities 9 . Unlike semiconductors that are reaching fundamental limitations for device fabrication, graphene based electronic devices hold an immense potential for future electronics 6,8,10 . Proteins confer exceptional stereospecificity to graphene when covalently attached in the design of biosensors. Glucose oxidase (GOx), a redox enzyme that increases the rate of glucose oxidation, has been extensively employed in biosensors to determine the concentration of glucose in biofluids by estimating the number of electrons released during the redox reaction [11][12][13][14][15] . GOx in conjunction with graphene interface acts as an efficient conveyor belt, receiving the electrons from flavin adenine dinucleotide (FAD) cofactors in GOx and ballistically transporting them as output, to give a direct quantitative measure of glucose in biofluids 8 . The graphene-protein interface is the gateway through which electrons shuttle from the FAD centers in GOx 4 .
Structural details of immobilized GOx on pristine graphene are hard to derive, and at present, the repertoire of structural methods are available to investigate interfaces which are largely limited to in silico molecular dynamics 4 , small-angle scattering, and 3D NMR imaging. Small-angle neutron scattering (SANS) probes structural features in the region from 1 nanometer to hundreds of nanometers. The prime objective of the present SANS study is to establish a detailed understanding of the GOx matrix structure deposited on graphene and relating the structural modifications to different sample conditions, and in future relating this information with the functionality of sensors in different applications.
Recent enhancements in capabilities of small-angle scattering techniques for biological samples have occurred in parallel with new methods for analyzing and modeling of data 16,17 . SANS provides unique capabilities to determine the organization and hierarchical structures of different characteristic length scales in a single measurement 18 . In the present study we have applied a novel scaling approach to Unified Fit 19 based analytical method to simultaneously extract the structure of individual GOx macromolecules in the biosensor and the architecture of assemblies that it forms within the sensor material. We use the Unified Fit in combination with ab initio methods provided by tools in the openly available ATSAS software suite and rigid body docking to obtain biologically relevant structural models for different structural levels 20,21 . The scaling approach overcomes the limitations of ab initio models in order to evaluate average models of the hierarchical assemblies. The results of this study demonstrate the ability of SANS to differentiate between changes in hierarchical structures in sensor matrices, which correlates well with the individual manufacturing processes. Figure 1 shows a brief layout of the approach for sample preparation and data analysis. The details of the sample preparation are discussed in the beginning of Materials and Methods section. It is followed by the details of small angle neutron scattering methods and data analysis. The next section discusses the information extracted from the SANS results and ab-initio models, that are compared with the electrostatic potential on the GOx crystal structure evaluated using continuum electrostatics calculations.

Results and Discussions
We have investigated the structural details of GOx-graphene sensor material on a length scale spanning 1-200 nm by small-angle neutron scattering (SANS). Figure 2(a,b) shows SANS data for two samples prepared by incubating graphene with recombinant GOx in buffer solution at pH 7 and pH 9, respectively. The scattering intensity shows several distinct bends which were analyzed with the help of a 3-level Unified Fit using Eq. (1) 19 . This analysis approach yields a set of parameters that describe the average topological arrangement at each level of the The samples composed of functionalized GOx matrix that is investigated using a multi-physics approach for SANS data analysis as discussed.
www.nature.com/scientificreports www.nature.com/scientificreports/ hierarchical structure. The parameters extracted from these fits are given in Table 1. We discuss the significance of these structural parameters in the following section, beginning at the smallest level of structure.
A size parameter in the form of apparent radius of gyration, R g of 25 to 26 Å is observed in both samples at the largest measured scattering angles (q > 0.04, see materials and methods for the relation between scattering angle, scattering vector q, and observed length scale). This size matches with the length scale of individual GOx enzymes and interpretation of this feature as stemming from GOx enzymes is therefore very plausible. The overall envelope shape of individual enzyme molecules in solution can successfully be obtained from small-angle scattering data 21 . For a dense packing of enzymes as encountered in the GOx sensor material, such a detailed analysis is obstructed by the additional scattering features that arise from the higher-levels of structure. In order to overcome this limitation, we have subtracted the higher-level scattering features, which were determined by their corresponding 3-level fit parameters. The residual scattering was then used for generating shape models of GOx enzyme by applying tools from the ATSAS suite as described in detail in the methods section 22,23 .
The final DAMAVER density maps for GOx enzymes in the sensor matrix of sample 1 and 2 are shown as blue surface in the central column of Fig. 3(e,f). GOx models for both the samples show a narrowed waist region in the center21,22. This feature is more prominent in sample 2. A comparison of these shape models with the known crystal structure of GOx is shown in Fig. 3(g,h), which depicts a quantitative rigid-body docking of the high-resolution structure into the low-resolution DAMAVER density map of sample 1 and 2 respectively. The resulting docked complex was inspected and visualized using PyMOL 24 . Apparently, the GOx dimer high-resolution structure, which was obtained through crystallizing GOx from a dilute solution, describes the conformation of GOx in the graphene sensor material rather well, especially for the sensor material prepared at neutral pH 7. Intriguingly, the sensor material that was prepared at basic pH 9 shows a somewhat increased separation between the subunits-note that some residues on the left side of Fig. 3(h) do not fit well into the more separated envelope structure.
Since the differences in sample preparation are in the pH environment, the pronounced neck region for sample 2 can be further examined using electrostatic potential (EP) evaluation employing continuum electrostatics calculations, shown in Fig. 3(i,j). The output has been generated using Jmol by PBD2PQR on a linear red-green-blue colour scale representing EPs of −7.5−0K B T/e. The EP over the structure differs markedly in the neck region of the dimer structure. The marked differences in the electrostatic potential distribution in the neck region may alter the electrostatic interactions at the dimer interface, and hence, induce greater separation of the dimer subunits at the elevated pH level 25 . Importantly, changes of the electrostatic potential may lead to altered glucose recognition and loss of its catalytic abilities. We note that this spatial separation is permanently retained in the final sensor material, since the SANS data was acquired after washing the material with neutral buffered saline solutions after functionalization at higher pH. The graphene functionalized GOx sensor material is organized into nano-to mesoscale clusters with an average diameter of just above 1000 Å. This is evident from the observed gyration radii at low scattering angles (q < 0.01 Å). The Unified Fit here yields overall size parameters R g of 590 Å and 550 Å for sample 1 and 2 respectively. The steep drop-off in intensity, which was fit by a q −4 power-law supports the notion of 3-dimensionally extended dense clusters that are bound by a well-defined surface. The inferred dimension and nature of the clusters compare well with the reported ESEM micrographs of surface morphology of immobilized GOx on chitosan supported mesoporous carbon 26 and cross-linked enzyme aggregates of horseradish peroxidase and GOx reported previously 27 . The limitations of the surface morphology information from the ESEM micrographs are testimony to the utility of the present work where (submicron) cluster morphology is deciphered using SANS.
In this same context, it is appealing to extend the envelope shape modeling approach to the larger structural features of the GOx sensor material. Such an approach is generally not possible with modeling software that is optimized for the smaller scales of enzyme structures. We introduced here a new approach to circumvents this limitation. We used structural models obtained from SANS using the ATSAS dummy atoms model (DAM) where the shape was calculated from the individual level scattering contributions obtained from the 3-level Unified Fit using Eqs (6-8). As shown in Fig. 2(c,d), we rescaled the two larger-scale structural levels along the q-axis to match the overall size of the GOx dimer using Eq. (10). This step of demagnification is necessary to allow fitting 1 . An exhaustive 6D conformational fitting was preformed on the high-resolution crystal structure into the modeled low-resolution averaged molecular envelopes to derive the docked complexes of sample 1 (g) and sample 2 (h). Comparison of surface electrostatic potentials under pretreatment conditions of pH 7 for sample 1 (i) and pH 9 for sample 2 (j). The blue-green-red linear color scale below (i) and (j) represents EPs in units of k B T/e (T = 298.15 K). the larger structural levels into the limits of the volume of the search box of the dummy atom-modeling program. Of course, this approach implies a coarsening of the model resolution with increasing levels of structural hierarchy, such that the size of details as represented by the rescaled dummy 'atoms' of each structural level is proportional to the overall size of that structural level.
The dummy 'atom' models obtained for the clusters look similar for both samples as shown in envelope structures in Fig. 3(a,b). We emphasize that the cluster structure models are derived from scattering intensities as parameterized by the respective Unified Fit curves and taking into account experimental error bars using Eqs 7 and 10. These models consequently do not contain more information than what is represented in the Unified Fit parameters. Moreover, the DAMMIN algorithm was developed for compact globular proteins and utilizes a built-in bias that favors connected, compact structures. Generally, the conversion of a scattering intensity curve in to a 3-dimensional real space model does not have a unique solution. Thus, the models generated by our new scaling approach need to be interpreted cautiously. Even so, the generated envelope structures are valuable as an intuitive illustration of plausible real-space structural features which are consistent with the SANS data.
Independent of any models, the SANS data allows in estimating additional quantities of interest: The ratio of absolute scattering intensity of the cluster to that of the individual GOx enzyme gives an estimate of the number of GOx dimers in the cluster. This number is about 9500 in sample 1 and 4600 in sample 2. Moreover, from the comparison of the size parameters of the cluster and GOx dimer we can estimate that the cluster volume is approximately 12400 times larger than the GOx volume in sample 1 and 9300 times larger than in sample 2. From this we can estimate a packing density of GOx enzymes of 0.76 in sample 1 and 0.50 in sample 2. These are rough estimates as uncertainties accumulate in the combination of fit parameters and anisometric shape of particles was not taken explicitly into account when estimating volume scaling from R g scaling. Nonetheless, these results suggest that GOx is packed quite densely in the sensor material prepared at neutral pH while preparation at higher pH leads to a somewhat less dense sensor material at the nanoscale. A lower packing density in the material prepared at pH 9 is consistent with repulsive surface charges on the GOx discussed above. Lower packing density of the sensor material provides a second plausible explanation for the lower performance observed in sensors prepared at higher pH.
Additional details of the spatial arrangement of GOx molecules inside clusters of graphene sensor material can be extracted from the central region of the scattering curves . < < . q (0 01 0 04). The 3-level fit represents here mass fractals of similar overall size R g of 108 to 110 Å for both samples but with differing power law exponents d f of 2.34 and 2.86 respectively. The presence of this intermediate length scale of scattering signifies additional spatial correlations in the material that would not be observed by a simple, homogeneous, random arrangement of GOx within the large clusters of the material. Rather, it signifies specific structural arrangement at an intermediate scale. This feature is more pronounced in sample 2 prepared at pH 9. The 3-level Unified Fit implies that this intermediate scattering level represents aggregates composed of the smaller scale level GOx dimers. Following this interpretation, we find the number of GOx enzyme molecules in these mass-fractal aggregates, z a , evaluated from the absolute scattering intensity to be 10 and 17 for sample 1 and sample 2 respectively. On the other hand, if we assume that volume scales as R g 3 , then we find that the volume spanned by the aggregates is 70 to 80 times larger than that of GOx, which leads to a low space filling of GOx molecules of 0.12 and 0.24 for sample 1 and 2 respectively.
On the other hand, the comparison of size parameters of aggregates and the larger clusters yields large numbers of several hundred aggregates within a cluster (z c , Table 1), which would require packing fractions greater than 1 (6 and 2 for sample 1 and 2 respectively). A packing fraction of 1 represents complete space filling and numbers greater than 1 are not physically feasible. One possible explanation for this observation is that aggregates are not isometric but rather spatially extended in one or two dimensions, such as forming rods or platelets. Scaling as R g 3 would then grossly misrepresent the aggregate volume. In this scenario, R g would initially grow fast as GOx packs for example into aggregate platelets, and then slow, as platelets stack to form clusters, in agreement with the observed SANS data. Platelets would exhibit a scaling exponent = d 2 f in the q-range that corresponds to length scales larger than their thickness but smaller than their radius 28 . The unified fit yields power law exponents d f of 2.34 and 2.86 which are not quite consistent with platelets but which would allow anisometric fractal objects that grow slower in volume than R g 3 . The lower exponent for sample 1 suggests that such aggregates may be more flattened for samples prepared at neutral pH rather than basic pH.
Dummy atom models of aggregates representing the intermediate structural level are shown in Fig. 3(c,d), which is composed of z a GOx dimers. As pointed out earlier, these envelope models should not be overinterpreted. Nonetheless, the differences in the morphology of the two samples, as expected from their respective fractal exponents d f , clearly stand out in these models. Sample 1 exhibits a thick two-dimensional fractal structure, while sample 2 points towards a more branched, 3-dimensionally packed structure that encompasses a considerable concentration of cavities. Importantly, the presence of pores in sample 2 is consistent with the observation presented earlier that clusters in sample 2 are less densely packed with GOx than in sample 1.
Low aggregate mass density structures typically show lower conductivities [29][30][31][32] due to the presence of lower connectivity 18,33,34 . A general dependence of resistivity on fractal topology can be evaluated using simple Cates scaling theory 35 , which would appear to be appropriate in the context of the present investigation. For example, a random walk upon a lattice of native mass fractal dimensions of d f , results in a path of fractal dimension d /2 f . Then the resulting resistances can be expected to scale as ΩR R ( ) 1/ d /2 f . This confirms that the resistivity contribution from aggregate arrangement would typically be higher for lower fractal dimension structures.
In conclusion, we have shown here the use of SANS to probe structural features of GOx proteins in solid form of sensor matrices. The methodology to generate representative spatial models for the hierarchical structures of enzymes on glucose sensor surface by combining Unified Fit analysis with the widely used ATSAS suite has been demonstrated. The overall performance of the sensor material is expected to result from a combination of the average enzymatic functionality of matrix-embedded GOx dimers and the conductance of graphene-functionalized GOx topologies at different length scales. This work demonstrates the power of SANS-based analysis for obtaining structural information that can help understand these competing factors in bio-composite sensor materials. The modeling methodology introduced here can be generically used in device configurations or other bio-macromolecule based functional materials. The methodology brings to light some unique opportunities for the application of SANS to predict or infer the performance of bio-hybrid sensor matrices in solid form on complex substrates.

Materials and Methods
Recombinant GOx expression and purification. The gene encoding a glucose oxidase from Aspergillus niger BT18 (Target species: ASPNG; Uniprot ID P13006) was cloned into a replicative plasmid vector and expressed in Kluyveromyces marxianus var. marxianus CBS 6556 strain as described previously 36 . A partially purified enzyme (Medium grade GOx) obtained from cell-free supernatant prepared by culture centrifugation (13,000 rpm, 30 mins, 4 °C) was concentrated and exchanged by Prep/Scale Spiral Wound Ultrafiltration with a pore size of 10 kDa (Millipore) in 20 mM Tris buffer (pH 7.4) with 100 mM NaCl. The pure enzyme (High grade GOx) was subjected to a second purification step with Q-Sepharose F.F. column (strong anion exchanger) equilibrated with the same buffer, and a linear gradient of 0-0.5 mM NaCl in 20 mM Tris buffer (pH 7.4) was used to elute the column at a flow rate of 0.5 ml.min −1 . Enzyme activity recovery and purification factor were 89% and 1.5 for the Medium grade GOx, and 17.3% and 17 for the High grade GOx. Both Medium grade and High grade GOx were lyophilized to achieve higher stability at room temperature. All steps of purification were assayed for their enzyme activity and protein content. GOx's activity was determined by the o-dianisidine reduction method using a commercial glucose oxidase from Aspergillus Niger (G6125, Sigma, USA) as standard at 37 °C and pH 4.5 37 . The homogeneity of the partially and highly purified protein was confirmed by SDS-PAGE analysis (Fig. S1) and the protein concentration was determined by Bradford method using BSA as standard 38,39 . Single layer graphene deposition. Single layer graphene film was synthesized on a 25 μm thick clean copper (Cu) foil by the chemical vapor deposition technique using hexane as the carbon source 40 . The Cu foil was loaded in a quartz tube and the tube was pumped down to 10 −2 Torr using a vacuum pump, before flowing in Ar/ H 2 mixture gas at a pressure of ∼8-9 Torr with a flow rate of ∼400 standard cubic centimeters per minute (sccm). The Cu foil was then heated to 950 °C in Ar/H 2 atmosphere. When the temperature becomes 950 °C, Ar/H 2 flow was stopped and hexane vapor is passed through the quartz tube maintaining the tube pressure of 500 mTorr for 4 min. The flow rate of hexane was maintained at ~ 4 mL/h (~2-3 sccm). The furnace was then suddenly cooled to room temperature. The graphene growth has taken place over Cu foil and this film was further processed for PMMA based transfer process. functionalization of Gox. A graphene device (CVD Graphene or Graphene Foam) was incubated with a 5 mM linker molecule (1-pyrenebutanoic acid succinimidyl ester, Santa Cruz Biotechnology, SC-213409) in dimethylformamide (DMF) for 2 hours at room temperature and washed with pure DMF and deionized (DI) water for three times. The linker-modified graphene was then incubated with 10 mg/mL of recombinant GOx in Na 2 CO 3 -NaHCO 3 buffer solution (pH 7.0 for Sample 1 and pH 9.0 for Sample 2) overnight at 4 °C followed by rinsing with DI water and phosphate buffered saline solution (PBS, pH 7.2). To deactivate and block the excess reactive groups remaining on the surface, the device was further incubated with 0.1 M ethanolamine solution (pH 7.0 for Sample 1 and pH 9.0 for Sample 2) for 30 min and then rinsed with DI water. Raman spectrum of GOx immobilized on single layer graphene (SLG) collected at ~ pH 7 (blue), after subtraction of SLG, is shown in Fig. S2, which shows well-resolved amide I, III regions, confirming that GOx was successfully immobilized on Graphene surface. The enhancement of the G band assigned for the sp 2 carbon is an indication of reconstruction of the carbon network after immobilization of GOx on the graphene surface 26 .
Sample geometry. The device has a stack of single layer graphene sandwiched between two gold pads deposited on top of Silicon Dioxide layer on a silicon wafer. A few microns thick layer constituting of an estimated 600-1,000 layers of functionalized GOx deposited over the single layer graphene layer constitutes the activated matrix investigated using SANS. A schematic of the active matrix under investigation is shown in Fig. 4(a).

Small-angle neutron scattering. SANS experiment. SANS experiments were performed at the
Bio-SANS instrument at the High-Flux Isotope Reactor in Oak Ridge National Laboratory 41 . The instrument schematic is shown in Fig. 4(b). The sample, GOx sensor matrix was held on a silicon wafer by sandwiching between two quartz slides. The GOx sensor matrix was positioned to have the neutron beam transmit as used for transmission mode measurements. A 2D position sensitive neutron detector housed in a vacuum tank acquired the scattered neutrons carrying structural information of the protein. Three different instrument configurations of sample-to-detector distances (SDD) of 1.13 m, 6.83 m and 15.33 m were employed to acquire SANS data in a wide range of positions (0.003 Å −1 < q < 0.5 Å −1 ), at a wavelength of 6 Å with a wavelength spread, Δλ/λ of 0.15. The data acquisition time was 5 hours for each sample at each SDD configuration.
The SANS − I q profile was obtained by performing an azimuthal averaging of the 2D detector images on a 256 × 192 pixel matrix, normalized to incident beam monitor counts, corrected for detector dark current, pixel sensitivity, sample transmission and silicon wafer with SiO 2 and gold depositions as background.
Small-angle neutron scattering data reduction and analysis. In isotropic small-angle scattering as in present case, an azimuthally averaged intensity in units of cm −1 is plotted against a reduced angle, called the scattering wave vector q. www.nature.com/scientificreports www.nature.com/scientificreports/ used to quantify topological features in complex materials 20,42 . SANS from a hierarchical system displays multiple structural levels which can be evaluated using scattering laws for mass/size and surface/density properties 2,18,43,44 . In each structural level, a Guinier's law, − ( ) , and a power-law, − I q Bq ( ) d f , are observed at the lower and higher q-regions respectively, where G, R g , B and d f are the Guinier's law prefactor, radius of gyration, power-law prefactor and fractal dimension respectively 18,[43][44][45] . A Guinier-law is an exponentially decaying function, which decays near qRg = 1 region and the actual shape of the decay, also known as the Guinier knee, depends on the shape and size of a particle. On the other hand, the topological features of a particle can be inferred from the surface scattering via Power-law with two variables, B i and d f , at higher q. B i is directly proportional to the surface area of the particle while d f provides a measure of mass to size scaling or density of an average particle. These local scattering laws can be combined using the Unified Function to describe multiple levels of structures. The choice of the number of the levels used for the data interpretation depends on the features in the SANS curve.
Owing to the presence of three distinct bend/hump in the SANS curve (at q ~ 0.004, 0.02 and 0.07 Å −1 ), the GOx dimer system is fitted with a three level Unified Fit, as: 2,18,44,[46][47][48][49]  , and erf is the error function. The subscripts c, a and G indicate different levels of GOx organizations namely the clusters, aggregates and GOx dimer levels, respectively. The power-law prefactor 18,19,43,44,50 , where, n i and S i are the number and surface area of particles in a structural level while Δρ is the contrast factor. The power law exponent, more widely called the fractal dimension, is the mass to size scaling parameter. It is a direct measure of density whence a higher fractal dimension translates to a higher mass density. The Guinier prefactors 20,43,44,50 where, V i is the volume of particles in a structural level. Few GOx dimers constitute a larger average aggregate and several of such aggregates then form much larger clusters. Since the contrast, Δρ, remains the same across all the levels, the relation www.nature.com/scientificreports www.nature.com/scientificreports/ gives the number of dimers in an average aggregate, or the degree of aggregation in the aggregate structure. Similarly the number of these aggregates in the cluster can be evaluated by 47 , The ′ z s i are independent of absolute data calibration with the assumption that the i th level is composed of − i ( 1) th level structures.
Ab initio modeling of SAnS Data. Small-angle scattering techniques such as SANS are widely used to evaluate three dimensional protein structures by implementing ab initio modeling approaches such as the DAMMIN program in the ATSAS suite, developed by Svergun's group 20,21 . The program generates dummy bead coordinates of structures consistent with isotropic SANS experimental data 51 using finite volume ensembles with the help of parameterized envelope functions. The algorithm used to generate the individual volume elements is bound by constraints of compactness, which takes size and distribution inputs from GNOM fits of SANS data 21,52 .
The GNOM program can be conveniently used to fit single structural levels but presently has limitations with respect to hierarchical topologies.
In the present study, the total scattering intensity has been separated into a set of three distinct intensities such that, where, s q ( ) exp is the error from the experimental SANS intensity, I q ( ) exp . For ab initio modeling, the size ranges of the larger hierarchical structures were scaled to that of the GOx dimer in order to limit the search volume to generate appropriate dummy atom models using the GNOM fits. This was achieved by scaling the q-range of cluster and aggregate structures as, The result of application of Eqs (10,11) are shown in Fig. 1(c,d) for SANS data from sample 1 and samples 2 respectively. In the present study, the intensities obtained from using Eqs (7-9) were fit using GNOM which uses the distance distribution function, p(r), that may be calculated from the intensity using a Fourier transform, ∫ π = ∞ p r r I q sin qr qr q dq ( ) 2 ( ) ( ) In practice, the integration is over r = 0 to a maximum distance = r D max . In general, the D max is selected in the range of 2.5-3 times R g , depending on the feasibility of shape of the distribution function. We started with a D max of 70 and adjusted thereafter as required. The P(r) plots for the two samples for the GOx, aggregate and cluster levels are shown in the Fig. S3. The details of the D max are in the Table S1. The GNOM 52 output file is used to generate 20 low-resolution ab initio models using the DAMMIN program 21 . Thereafter, these set of 20 ab initio models were sorted, aligned and averaged using the DAMAVER program suite to generate final models 53 . Table S1 has the statistical details of the ab-initio modeling using ATSAS package including the normalized spatial discrepancy (NSD), the number of reconstruction included in the final model generated by DAMAVER and Dmax used for generating GNOM fits.