Influence of AgVO3 incorporation on antimicrobial properties, hardness, roughness and adhesion of a soft denture liner

The objective of this in vitro study was to investigate the effect of nanostructured silver vanadate decorated with silver nanoparticles (AgVO3) on antimicrobial activity, hardness, roughness, and adhesion of a soft denture liner. The antimicrobial efficacy of the Trusoft (Boswoth) liner incorporated with different concentrations of AgVO3 against Enterococcus faecalis, Pseudomonas aeruginosa, Candida albicans, and Staphyloccocus aureus (n = 5) was evaluated by the agar diffusion method. Roughness, hardness, and adhesion properties were also evaluated. The data were analyzed by analysis of variance (ANOVA) and Tukey’s multiple comparison test with significance at the p < 0.05 level. At concentrations of 1 and 2.5%, AgVO3 incorporation was effective only against E. faecalis, and at 5 and 10%, against E. faecalis, P. aeruginosa, and C. albicans. None of the concentrations was effective against S. aureus. A decrease in hardness was found for the 1, 2.5, and 10% AgVO3 concentrations (p < 0.001) and at 5%, hardness was not affected. None of the concentrations affected the roughness of the material. A significant increase in tensile values was observed between the liner and heat-curing acrylic resin for 2.5% (p < 0.001) and 10% (p = 0.042) concentrations. AgVO3 incorporation to a soft denture liner promoted antimicrobial activity against E. faecalis, P. aeruginosa, and C. albicans without affecting roughness, maintaining the hardness properties recommended for soft and extra soft liners, and improving the adhesion between the liner and the acrylic resin used for dentures.

reduction of surface roughness was observed with the incorporation of essential oils 20 . The addition of silver nanoparticles to a tissue conditioner in concentrations varying between 0.1 and 3.0% was effective against S. aureus, S. mutans (at 0.1%), and C. albicans (at 0.5%) after a period of 24 and 72 h 16 .
To add antimicrobial properties to denture liners while maintaining good physical and chemical properties, this study tested the incorporation of nanostructured silver vanadate, since its use was shown to be efficient in acrylic resin 21,22 .
Nanostructured silver vanadate decorated with silver nanoparticles (AgVO 3 ) is formed by a precipitation reaction between silver nitrate and ammonia vanadate and was described by Holtz et al. 23,24 . This substance showed promising antibacterial activity against strains of gram-positive bacteria, including methicillin-resistant S. aureus.
Therefore, the objective of this study was to incorporate AgVO 3 at 1, 2.5, 5, and 10% to a resin denture liner and evaluate the antimicrobial capacity, adhesion properties, hardness, and roughness. The null hypothesis was that there is no significant difference in the properties of the liner and antimicrobial effectiveness as a function of AgVO 3 concentration.

Material and Method
Synthesis of nanostructured silver vanadate. The nanostructured silver vanadate is synthesized through a precipitation reaction between silver nitrate (AgNO 3 , Merck 99.8%) and ammonium vanadate (NH 4 VO 3 , Merck 99%), as described previously [21][22][23][24] . After the solubilization of 0.9736 g of NH 4 VO 3 and 1.3569 g of AgNO 3 in 200 mL of distilled water, the AgNO 3 solution was added dropwise to the NH 4 VO 3 solution under constant stirring at 65 °C. The obtained precipitate was washed with distilled water and absolute alcohol, filtered, and dried under vacuum for 10 hours 23,24 . Materials characterization. Analysis of transmission electron microscopy (TEM). The presence and morphology of silver nanoparticles (AgNPs) on the surface of the crystals formed was verified by transmission electron microscopy (TEM) using the JEOL microscope JEM-100CX II (Fig. 1).
Analysis of Fourier Transform Infrared (FTIR) spectroscopy. The chemical composition of AgVO 3 was evaluated by Fourier Transform Infrared (FTIR) spectroscopy; that was performed using ATR technique with a diamond crystal detector coupled to the FTIR Spectrometer Nicolet 380 (Thermo Fisher Scientific Inc.; Waltham, MA, USA). For the measurement, the AgVO 3 were positioned in contact with the diamond crystal of the ATR setup. The infrared absorbance spectrum of the samples was obtained over the range of 4000-400 cm −1 at 1 cm −1 resolution using 32 scans and was recorded using the OMNIC Spectra Software (Fig. 2).
For the peak identification we employ the second derivative to the absorption spectrum to identify precisely the band position.
Analysis of X-ray diffraction (XRD). The structural changes were evaluated by x-ray diffraction (XRD) patterns. The patterns were collected using a Bruker AXS D2 diffractometer equipped with a Cu tube, using Cu Kα radiation (λ = 1.54 Å); in the range of 5-50°, with steps of 0.05°, with 0,5 s for each step (Fig. 3).
Preparation of the resin liner and specimens containing AgVO 3 . The powder of Trusoft (Boswoth) denture liner was weighed to obtain the amount of nanomaterial to be added. Fractions from 1 to 10% of the liner weight were subtracted to incorporate that amount of the nanomaterial, as described in Table 1.
For the antimicrobial, hardness and roughness analyses, the AgVO 3 + liner combinations were mixed for 30 to 40 seconds on an unpolished glass slab. The mix was placed in a metal mold (Ø 8 mm × 3 mm) and pressed between two glass plates to create sample disks. The entire procedure was done according to the manufacturer's recommendations.
For the adhesion analysis, a mold with 10 mm diameter and 20 mm height was used to obtain specimens in wax that were invested with plaster in metal flasks, creating a matrix for packing with heat or self-curing acrylic resin (Clássico Produtos Odontológicos, SP, Brazil). One hundred disks of each acrylic resin were obtained, which www.nature.com/scientificreports www.nature.com/scientificreports/ were polished under water with 320-grit sandpaper. Two disks of each resin type were positioned in a spacer and joined with the liner, generating 50 specimens for each resin (Ø10 mm × 43 mm, n = 10 for each percentage of nanomaterial).

Analysis of antimicrobial activity. The microorganisms Staphylococcus aureus (ATCC 6538),
Pseudomonas aeruginosa (ATCC 27853), Candida albicans (ATCC 90028), and Enterococcus faecalis (ATCC 29212) were obtained from thawed strains and cultured at 37 °C for 24 hours in a microbiological oven. Cultures were centrifuged at 6,000 g for 5 minutes, the supernatant was discarded, and the pellet was washed twice with 10 mL of PBS (Phosphate Buffered Saline, containing NaCl, KCl, Na 2 HPO 4 , KH 2 PO 4 ). The inoculum suspensions were made in BHI medium and the concentration confirmed by optical density using a spectrophotometer (BEL Photonics, model 1105, Piracicaba, SP, Brazil), with absorbance reading of 0.120 for P. aeruginosa, 0.150 for E. faecalis, 0.8 for S. aureus at 625 nm wavelength, which corresponds to 10 8 cells/mL. For C. albicans, cells were counted in the Newbauer chamber due to the variable morphology of the genus. After standardization of the suspensions, the inocula were diluted to 10 6 CFU/mL. TSA (tryptic soy agar) culture medium was used for P. aeruginosa and E. faecalis, Saboraud Dextrose Agar was used for C. albicans, and BHI (Brain Heart Infusion) was used for S. aureus.   www.nature.com/scientificreports www.nature.com/scientificreports/ To evaluate the 4 microorganisms, the agar diffusion method was performed with 5 specimens for each percentage of nanomaterial. Denture liner disks (Ø 8 mm × 3 mm) were exposed to UV light in a laminar flow hood for 30 min on each side for disinfection and then placed in petri dishes containing the culture media. The culture media for diffusion were heated to 50 °C for addition of the microorganisms. After 2-h rest, dishes were stored for 24 hours in an oven at 37 °C.
Hardness and roughness tests. The surface hardness analysis was performed using the microdurometer Microtest SD 300 (Moema, SP, Brazil) with five random equidistant measurements in each specimen using a Shore A indenter. The roughness was analyzed using the Mitutoyo analogue roughness tester (Mitutoyo Suzano, São Paulo, Brazil) with three measurements in each specimen: one in the center and two 1-mm from the central measurement.
The failure types of the test groups were observed and classified as adhesive failure -total separation at the interface between the liner and the acrylic resin; cohesive failure -separation within the liner; and mixed failurea mix of adhesive and cohesive failures.
Tensile bond strength was calculated using the equations below: where σ = stress (MPa), F = maximum recorded strength at failure (N), and A = original cross sectional area (mm 2 ).

Data analysis. After verifying the normal distribution of the data (Kolmogorov-Smirnov test), ANOVA with
Tukey's Multiple Comparison test (α = 0.05) was applied for comparisons and the Two Proportions Equality test to analyze the distribution of the relative frequencies (percentages). The software used was SPSS v 20.0.

FTIR, SEM and X-ray diffraction (XRD) analysis. The AgVO 3 morphology was examined by TEM, and
it shows that the synthesized sample is mostly rod-like particles (Fig. 1). The AgVO 3 are composed of nanowires with length in the order of micrometers. The wires are coated with semispherical metallic silver particles (Ag). Figure 4 shows the fourier transform infrared (FTIR) spectrum of AgVO 3 nanorods acquired in the range of 400-4000 cm −1 which is very similar to that reported for AgVO 3 22,23 . It was observed absorption bands at 908 cm −1 , 892 cm −1 , 860 cm −1 (broad band), 827 cm −1 , 817 cm −1 and 809 cm −1 . We didn't find the same bands in the literature, but for the same Ag/V molar ratio of the two used in this work, it was observed bands at 964, 915, 895, and 849 cm −1 23 . These absorption bands area was assigned to stretching vibration mode of the V = O bound.
In Fig. 3 it is observed the x-ray diffraction pattern of the silver vanadate. The x-ray diffraction pattern is a mean value of silver vanadate nanowires who are decorated with Ag nanoparticles. The data depicts that the sample is crystalline, but we didn't identify in this work its crystalline structure, remembering that we have certainly at least two-phase as suggested by the literature 23 , metallic Silver (Ag°) and silver vanadate (AgVO 3 ).
Antimicrobial activity. Antimicrobial activity was tested by the Kirby Bauer agar diffusion method. The incorporation of 1 and 2.5% AgVO 3 to the denture liner did not result in antimicrobial activity for P. aeruginosa and C. albicans, but it was effective at 5 and 10%; for P. aeruginosa, the 10% showed higher antimicrobial capacity. For C. albicans, both 5 and 10% concentrations showed similar antimicrobial effect. All preparations showed antimicrobial activity for E. faecalis in a concentration-dependent manner (with 10% having the highest effect). None of the concentrations was effective against S. aureus (Fig. 4).
Mechanical properties. The incorporation of 1, 2.5, and 10% AgVO 3 promoted a decrease in Shore A values (p < 0.001), while the 5% dose had no effect. The incorporation of 1% AgVO 3 produced specimens with a lower Shore A hardness value (average of 43.77), which is within the ISO standard of 40 units (DIN 53505 and ASTM D2240 / 75) for soft denture liners (Fig. 5).
The addition of the nanomaterial at all concentrations did not significantly affect the roughness of the denture liner. (Table 2).
For the heat-curing acrylic resin, a significant increase in tensile values was found for 2.5% (p < 0.001) and 10% AgVO 3 (p = 0.042), showing that the nanomaterial caused an increase in the adhesive property of the liner ( Table 3). The 2.5% concentration promoted the highest adhesion with a mean of 0.664 MPa. For the self-curing acrylic resin, no significant effect was found in strenght (N/cm and Kgf) and tension (MPa) in any of the groups evaluated (Table 4).
Regarding the type of failure for the heat-curing resin, a significant difference was found in the 2.5% group, with 50% of mixed failures and the 10% group with 60% of adhesive failures. For the self-curing resin, a difference was found only in the 10% group, with 80% of adhesive failures (p = 0.007) ( Table 5). When comparing the two resin types, a significant difference was found only for the 2.5% group (p = 0.010), with 50% of failures within the heat-curing resin.

Discussion
The AgVO 3 formed had acicular morphology and length in the order of micrometers, and they are decorated with AgNPs, similar to the pattern observed in the images obtained by transmission electron microscopy (TEM) by de Castro et al. 22 and Holtz et al. 24 . The characterization showed a vanadate wire with a heterogeneous distribution   www.nature.com/scientificreports www.nature.com/scientificreports/ and few AgNPs decorating the surface of the nanowires, and both vanadate and Ag present antibacterial effect, which characterizes the antibacterial potential of the material.
The infrared absorption bands show very broad bands, and different works from the literature diverge from the nominal values of the bands position observed in this work. These differences can be assigned for different Ag/V molar ratio and also to the synthesis. AgVO 3 is a promising alternative to provide antimicrobial capacity to various materials 23 such as water-based paints 24 and, in dentistry, acrylic resin 21,22 .  Table 3. Mean, median, and standard deviation (SD) for tensile values between a denture liner incorporated with nanostructured silver vanadate at different concentrations and a heat-curing acrylic resin.   www.nature.com/scientificreports www.nature.com/scientificreports/ In relation to the efficacy of silver vanadate antimicrobial properties it was seen that the antimicrobial mechanism of AgVO3 is attributed to the contact between the hybrid nanomaterial and bacteria 22 and occurs when Ag + is absorbed and released from the Ag nanoparticles through a direct dissociation between the nanoparticle and the bacterial cell wall, causing toxic effects 23,24 . Besides that, the AgVO 3 maintains a large surface area in contact with microorganisms, promoting changes in bacterial membranes morphology and loss of DNA's ability to replicate, which can cause cell death 23 . The surface of the bacterium has a negative charge at biological pH due to the dissociation of a large number of functional groups, including carboxylic and other chemical groups on the membrane. According to Li et al. 25 the semiconductor antibacterial mechanism is attributed to the oxidative stress caused by the production of OH*, O 2 and and O 2 H *, that is, when reactive species with complex groupings such as AgO 3 VO are formed a cluster in the reaction where O 3 decomposes into hydroxyl radicals and protons. At the same time, an electron transferred to the molecule of O interacts with the proton, forming an O 2 H* radical. Thus, bacterial death occurs through collaboration between surfaces 26 .
In this study, nanostructured silver vanadate was incorporated into a resin denture liner and the following properties were evaluated: antimicrobial effectiveness, roughness, hardness, and adhesion. The null hypothesis that the addition of AgVO 3 does not significantly affect the properties of the liner and antimicrobial effectiveness in a concentration-dependent manner was partially accepted.
Soft resins used for denture lining can serve as reservoirs for microorganisms 1 even when hygienized 10 due to their porous and irregular surface. Thus, research has been carried out for finding antimicrobial possibilities 1,6,20,26-28 to simultaneously treat infected mucosa and decrease denture fungal infections 29 . However, antimicrobial agents generally affect the physicochemical and mechanical properties of the material 6,18 . Denture liners contamination favors numerous diseases of the respiratory tract that cause serious health problems 14,17 . Even with the proven effectiveness of silver nanoparticles (AgNPs) 16,30,31 , silver nanoparticles aggregation reduces the surface area of the nanoparticles and the emission of silver ions, reducing the antimicrobial effect of the particles 27,31-33 . Holtz et al. 24 found that, in addition to a possible antibacterial action, silver vanadate acts as a carrier for the silver nanoparticles, allowing a continuous release of silver ions, and avoiding possible accumulations of AgNPs, and consequently maintaining a large surface area.
In this study, the resin liner incorporated with 1 and 2.5% AgVO 3 showed antimicrobial activity for E. faecalis, and 5 and 10% for E. faecalis, P. aeruginosa, and C. albicans. None of the concentrations was effective against S. aureus (Fig. 4).
The cell wall of Gram-negative bacteria comprises a fine peptidoglycan sacculus which is covered by an outer membrane. In contrast, Gram-positive bacteria have the much thicker cell wall, with multiple layers of peptidoglycan, and the presence of additional glycolipers in addition to other protective surface structures 34,35 . These additional glycopolymers are essential in maintaining the bacterial architecture, replication and other major cell functions, are highly diversified and generally species or strain-specific. Most Gram-positive bacteria have two types of glypolymers, one peptidoglycan-attached and one lipid-attached, although some bacterial species have three or four different glypolymers 35 .
Our research evidenced the presence of a different antibacterial effect for two of the gram positive bacteria tested, with effect for E. faecalis and no effect for S. aureus. This difference may be related to the presence of different additional glypolymers in the cell wall of both bacteria. The effect of AgVO 3 on P. aeruginosa is probably due to the thin cell wall, characteristic of gram negative bacteria.
According to Holtz et al. 23 the contact of AgNPs change the bacterial membrane morphology, and when bound to DNA, they affect bacterial metabolic processes, in particular cell division, causing cell death. As for C. albicans, AgNPs function by breaking down the membrane potential and forming pores, causing leakage of ions and other materials inducing apoptosis and causing ultrastructural changes 36,37 .
In one of our previous studies 22 where cell metabolism analysis was performed using the XTT method, a decline in the metabolism of C. albicans was observed with the incorporation of 5 and 10% b-AgVO 3 and in the present study, 5 and 10% promoted antimicrobial effect.
Comparisons of the mechanical properties of modified denture liners among studies are difficult because of the various methods used to evaluate the properties 7,18,39,40 . Trusoft has been tested for different properties such as porosity 7 , hardness 18,39 , absorption 39 , solubility 39 , and traction 39 . Although the composition of Trusoft is not specified by the manufacturer, its liquid component contains ethyl alcohol and low concentration of plasticizers, which guarantees a clinically acceptable smoothness for up to 6 months.
Soft denture liners should exhibit low hardness levels 18,39 , however, during use, they are susceptible to changes related to the leaching of plasticizers 40 . Mancuso et al. 39 found that thermocycling exerted a significant effect on the hardness of Trusoft due to the hydrophilic character of the material, which can lead to hardening through ethanol loss, water absorption, and loss of the plasticizer 7,41 . Urban et al. 18 observed a hardness increase of Trusoft when antimicrobial drugs were added, but the change was insufficient to interfere with clinical use. In the present study, the incorporation of 1% AgVO 3 produced specimens with hardness values in compliance with ISO requirements for soft liners (ISO 10139-2: 2009) 40  The bond strength of AgVO 3 -modified Trusoft to the heat-curing resin was higher for the 2.5 and 10% concentration, compared to the control group. In the attempt to elucidate this difference in the tensile strengh values, the tensile test was repeated for the 5% group, however, the same results were found. We suggest in a future study the accomplishment of the microstructural characterization proposing to analyze the structure-properties correlation in the attempt to find the answer for this difference in tensile strength means values for groups 2.5 and 10%.
Similar results were reported with the addition of 40 ppm silver nanoparticles (1.33 ± 0.22 MPa) compared to control (1.18 ± 0.17 MPa) 19 . In contrast, different results have also been found, where the control group (0.91 ± 0.52 N) presented greater tensile strength compared to the modified group (0.16 ± 0.05 N) 6 .
A previous study has reported a decrease of adhesive strength and changes in the type of failure with the increase of silver nanoparticles concentration 13 . In this study, the heat-curing resin had 50% of mixed failures in the 2.5% AgVO 3 group and 60% of adhesive failures in the 10% group. Takahashi et al. 38 found cohesive and mixed failures and a lower tensile strength for Trusoft without additives, compared to our results. The authors believed the findings were related to the high elasticity of the liner rather than bonding deficiencies. They also associated the failure of the liner to the low cohesive resistance of the material, which in turn provides information on the strength of the liner, rather than an accurate measure of the bond strength between liner and denture material 38 .
In the present study, the incorporation of different concentrations of AgVO 3 did not affect roughness, which is an important parameter, since the incorporation of antimicrobials to denture liners may increase the recommended roughness parameter of 0.2 μm 42, 43 .
The properties evaluated in this study were selected due to their clinical influence. An appropriate hardness allows the material to provide cushioning for the supporting mucosa. Adequate adhesion to the prosthesis and low levels of roughness are important to avoid the adhesion and proliferation of microorganisms.

Conclusions
The incorporation of 5% AgVO 3 to a soft denture liner was efficient in the control of P. aeruginosa, E. faecalis, and C. albicans, and 2.5 and 10% improved the adhesion properties between the liner and the denture base material. There was no effect on roughness and the 1% concentration maintained the recommended hardness properties of a soft material (ISO 10139-2: 2009). In conclusion, the AgVO 3 -incorporated denture liner is an efficient, practical, effective and accessible alternative for denture users with an oral infection.