Abstract
Plastic deformation and fracture of materials is accompanied by generation of elastic wave transients known as acoustic emissions (AE). A novel complex methodology combining the statistical analysis of distributions of time intervals between the successive AE events, and the unsupervised cluster analysis of the time series is proposed to test for possible correlations between emitting sources and to highlight their intrinsic dynamics. Aiming at revealing the essential temporal features of the twinning and dislocation dynamics, the proposed methodology was applied to the AE signals produced during plastic deformation in a magnesium alloy where both primary deformation modes  dislocation slip and twinning  operate concurrently. It has been undoubtedly demonstrated that the mechanical twinning belongs to a class of nonPoisson processes having a memory of the past in the millisecond range. As opposes to the correlated behaviour of twins, it was shown that the dislocation slip falls into the category of Poisson processes caused by independent sources.
Introduction
Motivation and Methodology
Plastic deformation in many metals and alloys with the hexagonal closepacked (HCP) lattice is mediated by a combination of dislocation slip and mechanical twinning  two primary mechanisms of plastic flow at low homologous temperatures. Local stress fields associated with twinning are pivotal in the deformation behaviour and fracture but are extremely difficult to characterize experimentally^{1}, particularly in dynamics whereby the twins interact with each other and/or with dislocations. Their mutual activity and interactions control the work hardening behaviour of magnesiumbased alloys. Both these mechanisms generate elastic waves commonly referred to as acoustic emissions (AE)^{2} reflecting the specific dynamics of the sources and allowing for unique access to realtime information on underlying deformation processes. Bearing a strong similarity to seismology^{3,4,5}, the AE technique, combined with multiparametric descriptive statistical analysis and pattern recognition methods^{6}, provides a powerful means of correlating the activity of elementary deformation processes  slip and twinning with the strain hardening behaviour^{7}. The influence of various metallurgical factors (texture, grain size, and solute content) on AE and underlying twinning and dislocation slip behaviour under different loading modes (tension or compression) has been investigated in significant detail^{8,9,10,11,12}. Similarly to pure FCC and BCC metals under uniaxial tensile loading, the AE activity in HCP Mg and its alloys commences at the very beginning of loading, peaks shortly after yielding and decays gradually with strain^{13,14}). Due to its inherent sensitivity to dynamic processes only, the AE technique is an ideal tool for probing intermittency of the plastic flow, which is spatially heterogeneous and temporally fluctuating in nature due to a discrete character of dislocations and their avalanches^{15,16}. AE stemming from dislocation mechanisms such as breaking away from unevenly distributed pinning points, motion between randomly spaced obstacles, escaping to a free surface at random locations along the gauge length, etc. involves a relatively large number of cooperatively moving dislocation segments and appears as an autoregressive stochastic process represented by a train of lowamplitude transients^{17,18}. The question remains if the same applies to mechanical twins arising as a result of the strongly correlated motion of twinning dislocations, and generating powerful AE bursts with the amplitude proportional to the length and velocity of the nucleating twin^{19,20}. The random AE time series can be fully characterised statistically in the multivariate space of features the shortest list of which includes the amplitude of transients and their interarrival times. In this way, the AE time series can be regarded as a point process. In fact, point processes can represent a wide variety of behaviours. The two most distinct types of underlying dynamics comprise a historyindependent behaviour of autonomous and uncorrelated sources, and a historydependent dynamics of interconnected, statistically correlated events. Thus, the temporal complexity of the collective dynamics of defects in solids during plastic flow is reflected in AE and can be made explicit through an adequate data analysis. While the statistical properties and the nonlinear dynamics of dislocation avalanches arising during both smooth and jerky plastic flow have been intensively studied using the AE amplitude distributions^{16,21,22,23,24}, the statistical behaviour of mechanical twins has not been explored to that extent^{25}.
The Poisson random process model is the first choice to assess the dynamics of the emitting sources and possible correlations between them. It has indisputably set the basis for modelling efforts in many fields. It has become a widespread tool in materials science and geoscience, aiming at characterising strongly localised deformation and fracture evolving on different scales in time and in different patterns ranging from the nanometrewide shear band in metallic glasses^{26,27} to rock mechanics^{4,28,29} and megaearthquakes^{30,31}. The Poisson distribution dominates the stochastic modelling philosophy whenever the sources are considered independent and it constitutes the grounds for a family of derivative renewal models accounting for deviations from the ideal Poissonian distribution due to the memory of the past and the correlation between the sources^{32,33,34} or due to inhomogeneity of the timedependent intensity λ which itself might be a stochastic process (c.f. Cox or Pólya processes and their generalisations)^{35,36}.
For the assessment of possible correlations in the behaviour of emitting defects, the AE time series is characterised by a single parameter – a set of arrival times of events \(\{{t}_{0},{t}_{1}\,\mathrm{...}\,{t}_{i}\,\mathrm{...}\,{t}_{N}\}\) as is commonly adopted for point processes. In practice, it is more convenient to investigate the distribution of time intervals between successive events \({\rm{\Delta }}{t}_{i}={t}_{i+1}{t}_{i}\), Fig. 1. Assuming that the sources of local stress relaxation resulting in the AE events are independent, one should observe a Poisson time series defined as a train of Dirac’s δimpulses \(\delta (t{t}_{k})\) with amplitudes U_{k}
and the interarrival time intervals Δt_{i} obeying an exponential distribution with the probability density function
where \(\overline{{\rm{\Delta }}t}\) is the average (over the time interval T) time interval between the pulses in a timeseries (or its chosen fragment) and \(\lambda =1/\overline{{\rm{\Delta }}t}\) is the average intensity (count rate or activity) of the pulse flow on the chosen time interval T.
Using the proposed robust statistical approach based on a blend of independent statistical procedures applied to the AE time series recorded during twinningmediated plastic deformation of the magnesium alloy ZK60, we endeavour to reveal (and make explicit) correlations in the collective dynamics of mechanical twins, and to demonstrate that twinning is a historydependent stochastic process.
Results and Data Analysis
Twin nucleation in HCP crystals occurs primarily from grain boundaries^{1,37} by simultaneous glide of multiple twinning dislocations^{38}. This cooperative dislocation motion produces strong AE transients rising to peak values within few microseconds since the twins nucleate very fast, at a sizable fraction of the velocity of sound^{39}, due to the fact that the stress required for twin propagation is lower than that for twin nucleation. Therefore, once nucleated, the twin propagates through the grain in both longitudinal and lateral directions until another twin variant, the opposite grain boundary or immobile dislocations impede twin movement. It has been well understood that AE results from rapid twin nucleation while the slow lateral twin growth (thickening) does not produce any measurable AE^{20,40,41,42}. The mutual interactions between twins can, therefore, be elucidated by the use of statistical analysis of transients in AE time series.
Raw data representing the typical AE time series recorded in the course of tensile testing of the Mgalloy ZK60 are shown in Fig. 1 at different scales revealing the discrete nature of AE signals mixed with continuous background noise. Similarly to most structural metals (c.f. Fig. 2 for wellannealed αFe), AE exhibits a broad peak after yielding, Fig. 1a, which then reduces as strain hardening proceeds. Figure 1b and c show that the AE stream in Mg alloy consists of a large number of randomly appearing wellseparated transient signals with broadly varying amplitudes. The AE arrival times \(\{{t}_{0},{t}_{1},\,\mathrm{...},\,{t}_{N}\}\) obtained from the continuously recorded AE signal constitute the point process as illustrated schematically in Fig. 1c,d. Since the properties of any random process are fully determined by a probability density function (PDF) of a descriptive random variable, the PDF \(\rho ({\rm{\Delta }}t)\) is obtained for each jth realisation, and the statistical goodnessoffit χ^{2} test is applied to probe the agreement between the interarrival times Δt and the Poisson distribution (2) with the count rate \({\lambda }_{j}={N}_{j}/T\) for each realisation \(j\in [1,K]\). Main findings of the statistical analysis are shown in Figs 2 and 3 for pure αFe and ZK60 alloy, respectively (for comparison, αFe is taken here as a representative of a class of materials deforming solely by intermittent dislocation slip mechanisms while the Mgbased alloy demonstrates profuse twinning). In these figures, the AE intensity \(\lambda \) is superimposed with the loading diagram and the original raw AE stream shown on a background.
It is instructive to notice that two generic types of AE behaviour – Poisson and nonPoisson, arise depending on the underlying deformation mechanism as highlighted in these figures. The individual slip lines, such as those reflecting the dislocationmediated AE response in pure well annealed Fe with mean grain size of 150 μm, Fig. 2, emerge on a free surface as a result of the collective dislocation behaviour which can be resolved by the modern AE technique revealing separated transients masked in the continuous noiselike signal^{17}. Even though every elementary slip event involves the correlated motion of a large number of atoms on a microscale, during strain hardening, numerous slip lines appear sporadically and independently in different grains of polycrystalline aggregates^{18}. The Poisson type AE is therefore reasonably expected unless the collective effects in dislocation ensembles come into force in the form of coarse slip bands or plastic instabilities^{43,44}. This can be nicely seen in Fig. 2, where the Poisson type AE is confirmed over the entire uniform hardening range in excellent agreement with the assumption made in^{18}, while the nonPoisson (correlated) behaviour is seen during the Lüders band propagation stage where the correlated dislocation behaviour is naturally anticipated. The collective dynamics of twins is notably different. Typical randomly chosen experimental distributions of interarrival times observed on different stages of deformation of the alloy ZK60 are shown in Fig. 4 where the expected ideal theoretical Poisson distributions with the count rate λ (same as that observed experimentally for a given sample) according to Eq. (1) are also displayed by solid lines. The χ^{2} test shows that at the very beginning of deformation, AE commences as the Poisson process, i.e. good agreement exists between the observed and expected exponential distributions of waiting times. The same can be said with high confidence for the mature stage of deformation (ca.12–20 s) before necking and fracture sets in. Similarly to Fig. 2, this is illustrated schematically in Fig. 3 by green squares. As opposes to this, the χ^{2} Pearson’s pvalue being much less than the 0.05 significance level suggests that we cannot accept the null hypothesis and that there is a significant difference between the observed and the expected Poisson distribution from approximately 5 to 12 s of the deformation process. This is highlighted by red on the intensity curve in Fig. 3. We should notice that this time interval corresponds to the appearance of the broad peak of AE intensity which is most commonly associated with the dominance of twinning in plastic deformation of Mg and its alloys^{41,45,46}.
To confirm the results of the \({\chi }^{2}\) hypothesis testing and to get a deeper insight into the nature of the event–event correlations, the independent Bitest^{47} was used. Originally proposed in astrophysics as a method for probing local correlations in time series, this test has been successfully used to characterise the statistics of the local fracture events during compression of shale rocks^{48}. As opposes to the Pearson’s the \({\chi }^{2}\) test, it is valid also for strongly nonstationary processes. The application of the Bitest with a floating window has fully confirmed the results of the \({\chi }^{2}\) test. In particular, in the realisations where the hypothesis of the exponential distribution of time intervals is rejected, the Bitest also suggests the presence of local correlations (the hypothesis of uniformity of B is rejected). Therefore, the consistency of the results of both independent tests can only lead one to conclude undeniably that there are local correlations in the studied stream of AE events.
As a matter of fact, two remarkably different statistics characterise AE data on different loading stages, and this has to be rationalised on the basis of operating deformation mechanisms. The observed significant deviation in the distribution of AE emitting sources from the Poissonlike behaviour is a prominent result since it expressly provides the evidence for the existence of a sort of statistical correlation between the defects underlying plastic flow in Mg and its alloys. To draw any conclusions on the nature of this correlation, one has (i) to identify the deformation mechanisms responsible for the observed correlations (e.g. dislocation slip, twinning, the interplay between these two, etc.), and (ii) to clarify its character by specifying an appropriate model of the nonPoisson process describing experimental data. To address the first problem, we employ the signal categorisation technique capable of distinguishing between different AE sources (see Methods for details).
Since the plastic strain associated with a single mechanical twin shooting through the grain is small^{49}, a part of plastic strain has to be accommodated by dislocation slip, and both mechanisms coexist in the course of plastic deformation. This implies that virtually any realisation of the AE random process contains contributions from both mechanisms and it is important to distinguish the respective contributions. This has been accomplished with aid from a quantitative statistical cluster analysis of AE time series in Mg and its alloys^{7,19,50,51}. This analysis is based on the premise that dislocation slip and twinning are significantly different in their dynamics and therefore they generate AE with different waveforms. Specifically, continuous lowamplitude waveforms produced by dislocation slip can be compared to high amplitude transients for twinning^{7,40}. Using the adaptive sequential kmeans (ASK) AE signal clusterisation algorithm^{6} (see also^{7,50,52,53} for details), the realisations of 4k samples with similar Fourier power spectral density (PSD) were grouped in the same category, while the realisations with statistically different PSDs were disjoined. This nonsupervised procedure reveals that the AE signals fall naturally into two primary categories with statistically different shapes of power spectra, as demonstrated in Fig. 5, representing the cluster centroids (mean PSD) for each AE source. Evidently, both clusters differ in the relative fraction of low and highfrequency components in their PSD. The noiselike Cluster 1 is characterised by the prevailing lower frequency content and low amplitude AE, which is typically associated with the dominance of dislocation slip in materials. Cluster 2 is composed of highfrequency transient signals with high peak amplitudes assuming from the preponderance of mechanical twinning. Thus, following the similar reasoning provided in^{7,50,53}, Cluster 1 was associated with dislocation slip while Cluster 2 was attributed to twinning which appeared to be predominant from 5 to 12 s of deformation, Fig. 3. One should bear in mind that, in fact, as deformation proceeds, both deformation mechanisms  dislocation slip and twinning  coexist contributing to the resultant AE throughout the entire loading process. The ASK algorithm makes it possible to identify the predominant mechanisms underlying the particular stages of strain hardening, and the contributions of each mechanism to the released AE energy have been found to be different depending on the strain, c.f. also^{7,50}.
The remarkable result is that both independent data processing methods (the analysis of the distributions of waiting times between transients and the cluster analysis) show a strikingly good agreement on the time domains where the AE time series has distinct statistical features, Fig. 3: the nonAE Poisson behaviour is observed when the twinning appears as a dominant deformation mode, whereas when dislocation slip prevails as the predominant mechanism of plastic deformation (after of 12 s deformation), the AE obeys the Poisson statistics. In other words, while the dislocation motion during uniform plastic flow can be regarded as a random process of independent, uncorrelated sources, the mechanical twinning is a stochastic process with intrinsic correlations or some memory of the past.
The most intriguing finding of the present work is the deviation of the experimental AE timeseries generated by mechanical twinning from the ideal Poisson process. The observed memory of the past can be short or long resulting in a conceptually different understanding of the background process. The short memory processes are grouped around a Poissonian background process with possible foreground dependants triggered by Poissondistributed precursors while emphasising the long memory in the temporal and spatial evolution leads to selforganised criticality, powerlaw behaviour and long tail distributions. In order to get a deeper insight into the nature of this phenomenon, one has to identify a model of the point process which adequately describes experimental data.
A broad variety of candidates belonging to different classes of stochastic processes can be considered as potentially appropriate for characterising the observed correlations. Generally speaking, a temporal point process is specified through its conditional intensity function \({\lambda }^{\ast }{(t)}_{{H}_{t}}\) defined as^{35,54,55};
where the subscript H_{t} denotes symbolically the history of the process to time t, containing the list of arrival times (i.e. \({\lambda }^{\ast }\) at the moment generally depends on all t_{i} < t), \({f}^{\ast }(t)\) is the conditional probability density function and \({F}^{\ast }(t)\) is the cumulative distribution function (CDF). Here the term “conditional” indicates that the process depends on the past and evolves. Hence, the conditional intensity function appears as a convenient means characterising how the present depends on the past in an evolutionary point process. For the Poisson process, the conditional intensity function is equal to the historyindependent intensity \(\lambda (t)\) entering Eq. (2), i.e. \({\lambda }^{\ast }{(t)}_{{H}_{t}}=\lambda (t)\).
Let us recall that a class of point processes, which are referred to as renewal processes, is defined via independent identically distributed intervals. The Poisson processes (both homogeneous with \(\lambda (t)=const\) and heterogeneous with \(\lambda (t)\ne const\)) belong to this class. Considering its alternative with the short memory of the past, the socalled Hawkes process introduced in 1971^{34,56} is admittedly one of the bestknown candidates. In this process, the parent events follow a Poisson process, and multiple generations of descendants are triggered, relative to their parent. In this sense, the Hawkes process can be regarded as the “autoregressive” point process^{35}. Modifications of this model have become the predominant models for earthquake aftershocks (ETAS) as well as for many other applications. Unlike Markovian processes disregarding the history of the process, the idea of the Hawkes process is centred on the premise that the memory of the past is an important intrinsic property of the generating process. Thus, the Hawkes process is the simplest extension of the Poisson point process, in which past events influence future events in such a way that the occurrence of any event increased the probability of further events occurring. It is therefore defined as a point process whose conditional intensity is a function of the past data \({H}_{t}\)^{34,56}:
where \(\mu \in (0,\infty )\) is the positively defined deterministic count rate providing a Poisson base level for the process, and \(\varphi (t{t}_{i})=a{e}^{C(t{t}_{i})}\) is the triggering/selfexcitation kernel, which regulates the intensity at time t that is made by an event that occurs in the past at a previous time \({t}_{i}\) (both a and C are the positive constants)^{57}. According to Eq. (4), each time a new event arrives, the conditional intensity increases sharply by a factor of a and then decreases exponentially back towards the μ value of the background Poisson process. Here a determines the magnitude of growth while С controls the rate of decay. One can notice that the conditional intensity (4) at the time moment t depends, indeed, on the whole time history t_{i} < t, and the set of model parameters includes μ, a, and C: \({\rm{\Theta }}=\{\mu ,a,C\}\).
The Hawkes model was tested for consistency with experimental AE data using the statistical procedure described in Methods section. The dataset shown in Fig. 1 was taken as a typical example for illustration. Assuming the Hawkes model, the optimal parameters determined by the NelderMead solver are given as \({{\rm{\Theta }}}_{opt}=\{\mu ,\,a,\,C\}=\{170,\,14.04,\,9.86\}\). The further detailed statistical analysis performed according to the scheme outlined above confirms that the Hawkes model provides an adequate firstorder fit to the investigated time series:

(i)
the cumulative distribution function, Fig. 6a, of the doubly transformed AE point process is linear for its U values;

(ii)
the QQ plot, Fig. 6b, showing the quantile of the distribution of \({\tau }^{\ast }\) in the rescaled AE time series against the quantile of the \(\exp (\,\,{\tau }^{\ast })\) distribution strongly suggests that both distributions are essentially the same;

(iii)
the points on the correlation plot \({U}_{i}{U}_{i1}\), Fig. 6c, are almost evenly distributed;

(iv)
the results of testing the null hypothesis that the distribution of interarrival times of the transformed process corresponds to the exponential distribution \(\exp (\,\,{\tau }^{\ast })\) with the pvalue greater than the criterial 0.05 while the initial distribution of interarrival times, Fig. 6d, cannot be considered Poissonian according to the same testing procedure.
In conclusion, the behaviour of AE produced primarily by mechanical twinning exhibits a short time correlation, and this memory of the past can be adequately described by the Hawkes type selfexcited point process.
Discussion
Virtually any modelling, including the probabilistic ones, inevitably exaggerates some aspects of the phenomenon of interest while disregarding others. An adequate model is supposed to highlight the essential aspects and shadow the less important details. In this sense, the Hawkes point process model of the observed AE behaviour is the first order approximation that adequately captures the most salient feature of mechanical twinning evolution in Mg and its alloys – it is a correlated process having the memory of the past not only at the initiation phase generating the AE pulse, but also during collective dynamics of twin ensembles generating pulse trains. It also suggests that this memory is caused by the influence of twinning events on the immediately following events on the submillisecond time scale. Figure 4(c–e) illustrate clearly that the largest deviation of the interarrival times from the exponential Poisson distribution is seen in the short time domain below 1 ms.
There is abundant literature regarding dislocationtwin and twintwin interactions^{58,59,60,61}, which helps to shed light on the observed temporal correlation between the twinninginduced events in AE time series. The possible reasons for that include (a) the twindislocation interaction revealing itself, for example, as the activation of dislocation slip ahead of the propagating twin^{58,62} to relieve the stresses that exist at the tip of the twin terminating within the crystal^{63,64} (Fig. 7a), (b) the relaylike “twin induced nucleation mechanism” (Fig. 7b) whereby the lenticular twin shoots through the grain, terminates at the grain boundary and promotes initiation of a new adjoined twin in the neighbouring grain due to the stress concentration at its tip^{65,66,67,68,69,70}, (c) lengthwise propagation of twin bundles (Fig. 7c) whereby several closely spaced parallel twin variants extend nearly concurrently in the same parent grain^{40} (see also^{71} for the evidence of twin clustering) and (d) autocorrelated jerky motion of the twin front (Fig. 7d) controlled by the intermittent flow of twinning dislocations^{72,73}. All of these scenarios are illustrated in Fig. 7 showing the consecutive snapshots of the specimen surface obtained by in situ highspeed video recording of deformation processes in Mg (the experimental setup has been described in^{74}). Although none of these three scenarios can be completely disregarded, the first three cannot be considered as leading contributors to the existing temporal correlations since their time scales do not match the relatively short characteristic times where the deviation of the observed process from the ideal Poisson distribution is observed in the AE signal. On the other hand, Fig. 7d illustrates that the thin twin lamella can advance rapidly in the longitudinal direction in the jerky “stopandgo” manner with short waiting times between jumps. It has been demonstrated experimentally and argued theoretically^{20} that even a micrometre scale advance of the twin with the velocity being of the order of the speed of sound, or a sizable fraction of it, induces measurable transient AE signals.
As a matter of caution, one should bear in mind that all the above considerations regarding the random data analysis have been originally developed for stationary (homogeneous) processes. One could reasonably suspect that the observed deviations of interarrival times from the Poisson distribution may not necessarily be caused by the longer memory of the past but might occur as a result of nonstationarity of the process at different points. Strictly speaking, the AE time series presented in Fig. 1, as well as other similar data we have obtained so far on Mg alloys, cannot be regarded as a “perfectly” stationary stochastic process, i.e. as a process whose unconditional joint probability distribution does not change in time. However, it can be considered as a weakly or “quasistationary” process on the time scale of individual realisations used for the analysis. Nevertheless, to make sure that the nonstationarity associated with varying AE activity cannot be the reason for the observed features, the same algorithm of signal detection and processing was applied to the synthetic time series simulating the strongly inhomogeneous Poisson process with the intensity \(\lambda (t)\) changing from 0 to 600 s^{−1} within 20 s according to the sine function. In all cases tested, the proposed algorithm correctly identifies the process as the nonstationary Poisson one even though the variation in λ was much stronger than that measured experimentally in our tests. Thus, the observed AE behaviour cannot be attributed to the nonstationarity of the slowly evolving timeseries.
Summary and Conclusions
The results of the present work provide new insights into the physics of the twinning generation process and the temporal evolution of plasticity in twinningprone materials through the proposed quantitative statistical analysis of the AE time series. The most intriguing result is that unlike dislocation slip, the mechanical twinning falls into a class of nonPoisson processes, i.e. it manifests itself as a process with a memory of the past. The AE time series were analysed statistically with independent methods from different angles, aiming at revealing fine features in the temporal dynamics of the underlying processes. The innovative thresholdless detection method was applied to determine the arrival times of events constituting the AE point process. The temporal event flow structure was described by the distribution of time intervals between successive events. Combining this analysis with the advanced adaptive sequential kmeans signal categorisation technique, the predominant contributions of both dislocation slip and twinning were separated in the AE signal. The dislocation slip appeared as the random Poisson process with the exponential distribution of waiting times between the points. As opposes to this, it was undoubtedly demonstrated that the mechanical twinning in Mg alloys did not belong to the same class. Rather it can be approximated by the Hawkes selfexcited process with the short memory of the past being of the order of 1 ms or less, and corresponding to the autocorrelated lengthwise propagation of the twin front.
As the additional outcome of this work, it can be concluded that the AE, when powered by modern signal detection, characterization and classification techniques, opens up a way to characterize the intimate details of the evolution of the dislocation and twin subsystems quantitatively. While each of the two proposed analytical methods  statistical analysis of the interarrival times and adaptive categorization of spectral density functions  taken in isolation offers access to the dynamics of the AE sources on different scales, employing them together yields a much more conclusive picture.
As a final note, we should notice that the observed nonPoisson type behaviour of the twinning–related AE sources during tensile deformation of the coarse grain alloy ZK60 is not specific to the alloy, its grain structure or the deformation mode. Although in the present work the conclusions were supported by the results obtained in monotonic tension of the specific alloy, essentially the same AE behaviour was ubiquitously observed whenever the twinning was a dominant deformation mode in pure Mg, Ti, Zn or in their alloys with different grain sizes subjected to either tensile, compressive of cyclic deformation.
Materials and Methods
Materials and testing
Commercial magnesium alloy ZK60 (Mg5.8Zn0.44Zr, in wt.%) with the average grain size of 70 ± 13 μm after hot pressing was used as a representative of materials prone to twinning. Further details of its microstructural characteristics can be found in^{7,75}. For the sake of comparison between the materials exhibiting twining and materials with dislocationmediated plasticity, a plate of high purity 99.99% αIron produced by Nilaco Corporation (Japan) was twostep annealed at 1250 °C and 900 °C for 1 h per step in vacuum to obtain a uniform microstructure with random texture and grain size of 100 ± 30 μm. Mechanical tests were conducted on flat dogbone shaped specimens having the gauge dimensions of 10 × 4 × 3 mm^{3}. The specimens from both metals were shaped by an electric wire cutter and mechanically polished to a mirrorlike finish. They were tensile tested to failure with a nominal strain rate of 5 × 10^{−3} s^{−1}. A miniature broadband AE sensor PICO was mounted securely on an unstrained shoulder part in close proximity to the gauge part of the specimen. Vacuum oil was used as a coupling medium to ensure efficient transfer of elastic waves from the surface to the transducer. The signal was amplified by 60 dB in the frequency band from 50 to 1200 kHz and transferred to the AE data acquisition system based on a 16 bits PCI2 (Physical Acoustics Corp., USA) board. AE recording was performed continuously in a thresholdless mode at a sampling rate of 2 MHz.
Data processing
Data processing includes the following steps:

(i)
signal detection and arrival time picking;

(ii)
analysis of the arrival time statistics by calculating the probability density function and performing its Chisquare goodnessoffit test for the Poisson distribution;

(iii)
independent Bitest for the same purpose;

(iv)
nonsupervised signal classification by the Adaptive Sequential Kmeans (ASK) clustering algorithm aiming at the discrimination between the signals mediated by dislocation slip and twinning;

(v)
modelling the nonPoissonian timeseries by a Hawkes type selfexciting process and its statistical verification vis à vis experimental data, using the random time change theorem.
Signal detection
To convert the continuously recorded AE data, Fig. 1a, into a sequence of arrival times, the signal detecting algorithm proposed in^{76} (see also^{77} for details) was used. The slidingwindow technique employed a time window of 4096 samples moving by 4 samples through the whole raw dataset. For each signal fragment, a Fourier power spectral density (PSD) function \(G(f)\) was calculated using a periodogram technique. The signal detector ϕ is constructed as:
with \({\rm{\Delta }}f={f}_{{\rm{\max }}}{f}_{{\rm{\min }}}\)  the frequency band. As long as the process is stationary, e.g., when no AE appears, and the recorded signal is due to noise, its spectral density does not change, \(G(f,t)=const\) and \(\phi (t)=0\). However, as soon as the burst AE signal arises and \(G(f,t)\) changes correspondingly, \(\phi (t)\ne 0\) and the signal is detected, Fig. 1c (inset). Due to the derivative nature of \(\phi (t)\), it is extremely sensitive even to the very subtle transient signals buried into the stationary background noise. To implement this algorithm, the raw streaming data were divided into K successive realisations of duration T, Fig. 1d, which is chosen to be long enough to ensure a sufficiently large number of events detected. For each jth realisation, the ϕtransform detects \({N}_{j}\) readings of arrival times \({t}_{j}\). Finally, a complete set of arrival times \(\{{t}_{0},{t}_{1}\,\mathrm{...}{t}_{i}\,\mathrm{...}\,{t}_{N}\}\) was obtained for the whole dataset.
Analysis of arrival times statistics
Since the properties of any random process are fully determined by the probability density function (PDF) of a descriptive random variable, the PDF \(\rho ({\rm{\Delta }}t)\) is obtained for each jth realisation, and the statistical goodnessoffit χ^{2} (Chisquare) test is applied to probe the agreement between the interarrival times Δt and the Poisson distribution according to Eq. (2). Note that for a Chisquare goodness of fit test, the null hypothesis states that the data are consistent with a specified distribution (Poisson distribution of interarrival times in our case). The alternative hypothesis is that the data are not consistent with the Poisson distribution. The null hypothesis is rejected if the computed Chisquare value is greater than the table critical value at a given level of significance. The process intensity (count rate) entering Eq. (1) is computed as \({\lambda }_{j}={N}_{j}/T\) for each realisation \(j\in [1,K]\).
Bitest
The advantage of this test is that it is applicable to strongly nonstationary processes. For each t_{k} event, a value \({B}_{k}=\frac{{{\rm{\Delta }}}_{k}}{{{\rm{\Delta }}}_{k}+{\delta }_{k}/2}\) is calculated^{47,48}, where \({{\rm{\Delta }}}_{k}=\,{\rm{\min }}\,[{t}_{k}{t}_{k1};{t}_{k+1}{t}_{k}]\) is the time distance to the nearest event, and \({\delta }_{k}=\{\begin{array}{c}{t}_{k1}{t}_{k2}\,if{{\rm{\Delta }}}_{k}={t}_{k}{t}_{k1}\\ {t}_{k+2}{t}_{k+1}\,if\,{{\rm{\Delta }}}_{k}={t}_{k+1}{t}_{k}\end{array}\) is the time distance to the second successive event. If the AE process obeys a local Poissonian behaviour, the variable B should be evenly distributed between 0 and 1 with the mean \(\langle B\rangle =1/2\). The deviation of the experimental cumulative distribution function F(B_{k}) from the theoretical uniform distribution according to the KolmogorovSmirnov test with the 95% confidence interval indicates the eventevent correlations.
Cluster Analysis
Mathematical details of this procedure are discussed in^{6} along with the benefits of this algorithm. The two most important features should be emphasised: (a) the number of clusters to be derived from a dataset is not specified a priori but is ‘datadriven’, and (b) the process is noniterative, i.e. the AE signals are associated with a certain cluster sequentially as they arrive one after another. The procedure starts with an evaluation of the power spectrum of a background noise, which serves as a first reference point for comparison and the first cluster creation^{6}. The symmetrised KullbackLeibler divergence \({d}_{KL}\) was chosen as a measure of pairwise similarity/dissimilarity between normalised discrete PSDs \({G^{\prime} }_{i}(f)\,\) and \({G^{\prime} }_{j}(f)\,\)^{6}:
Each signal is either assigned to the nearest cluster or is used as a seed of a new cluster. The algorithm tends to minimise intracluster distances and maximise intercluster distances.
Model verification (the goodness of the model fit testing)
When a candidate model for the process studied is considered (e.g. Pólya, Hawkes, Cox, or, etc.), it is necessary to check it against experimental data to verify how good it is. In statistics, the random time change theorem^{78} is often used for this purpose. This theorem is an important result of martingalebased point process theory demonstrating a fundamental possibility to transform a wide class of point processes into a homogeneous Poisson process. It states that if t_{1}, t_{2}, … t_{n} (\({t}_{i}\in [0,T],\forall i\)) is a realisation from a point process with the positive conditional intensity function \({\lambda }^{\ast }{(t)}_{{H}_{t}}\) and if the function
is strictly ascending and \({\rm{\Lambda }}(t) < \infty \), then the transformed timeseries \(\{{t}_{1}^{\ast },{t}_{2}^{\ast }\,\mathrm{...},{t}_{n}^{\ast }\}=\{{\rm{\Lambda }}({t}_{1}),{\rm{\Lambda }}({t}_{2})\,\mathrm{...},{\rm{\Lambda }}({t}_{n})\}\) called a residual (or rescaled residual) process form the Poisson process with unit rate^{55,79}. In other words, the distribution of rescaled timeintervals \(\{{\tau }_{1}^{\ast },{\tau }_{2}^{\ast },{\tau }_{3}^{\ast }\}=\{{t}_{1}^{\ast },{t}_{2}^{\ast }{t}_{1}^{\ast },{t}_{3}^{\ast }{t}_{2}^{\ast }\mathrm{..}\}\) should obey the exponential distribution with unit mean intensity \(\lambda =1\) and probability density \(f({\tau }^{\ast })=\exp (\,\,{\tau }^{\ast })\). This theorem yields a powerful means for both the diagnostics for point process models and/or simulation of various point processes. Since the point process is defined by the conditional intensity function:
which is a function of time t and the set of parameters Θ specific for a given model, c.f. Eq. (4) for the Hawkes model, it is plausible to start from the numerical computation of model parameters Θ_{opt} approximating the experimental count rate \(\lambda (t)\) using the NelderMead simplex optimization method^{80}. Optimal parameters Θ_{opt} are then used to compute the expected model intensity function \({\lambda }^{\ast }{(t)}_{{H}_{t}}\). Finally, the goodness of the model fit is verified on the basis of the random time change theorem with an aid from the following four independent statistical procedures which are commonly used to test the suitability of the candidate model.

(i)
The quantile of the \({\tau }^{\ast }\) distribution is plotted against the quantile of the \(\exp ({\tau }^{\ast })\) distribution for visual evaluation whether the two data sets come from populations with a common distribution.

(ii)
Transforming the intervals \({\tau }_{i}^{\ast }\) once again by applying the following transform
$${U}_{i}=1\,\exp ({\tau }_{i}^{\ast }),$$(9)one should obtain a set of uniformly distributed variables \(U\in [0,1]\). The mutual independence of variables U can be visually judged from the U_{i} vs U_{i−1} scatter plot. If the intervals \({\tau }_{i}^{\ast }\) are independent over the whole definition range, the uniform distribution of points is supposed to be seen. The irregular patterns such as dense clusters of points would assume a memory of the past or some sort of correlation between the events in the initial process.

(iii)
The CDF for the uniformly distributed variables U_{i} should be a straight line.

(iv)
The \({\chi }^{2}\) Pearson’s criterion can be used for quantitative comparison of the goodness of agreement between experimental interarrival times \({\tau }_{i}^{\ast }\) and the theoretical distribution \(\exp (\,\,{\tau }^{\ast })\).
References
 1.
Arul Kumar, M. et al. Deformation twinning and grain partitioning in a hexagonal closepacked magnesium alloy. Nature Communications 9, 4761 (2018).
 2.
Heiple, C. R. & Carpenter, S. H. Acoustic Emission Produced by Deformation of Metals and Alloys  A review: Part I and II. J. Acoustic Emission. 6, 177–237 (1987).
 3.
Aki, K. & Richards, P. G. Quantitative Seismology Theory and Methods. (W.H. Freeman and Company 1980).
 4.
Manthei, G. & Eisenblätter, J. In Acoustic Emission Testing: Basics for ResearchApplications in Civil Engineering 239310 (Springer Berlin Heidelberg 2008).
 5.
Weiss, M. & Louchet, F. Seismology of plastic deformation. Scripta Materialia 54, 747–751 (2006).
 6.
Pomponi, E. & Vinogradov, A. A realtime approach to acoustic emission clustering. Mech. Syst. Signal Proc. 40, 791–804 (2013).
 7.
Vinogradov, A., Orlov, D., Danyuk, A. & Estrin, Y. Effect of grain size on the mechanisms of plastic deformation in wrought Mg–Zn–Zr alloy revealed by acoustic emission measurements. Acta Materialia 61, 2044–2056 (2013).
 8.
Lamark, T. T., Chmelik, F., Estrin, Y. & Lukac, P. Cyclic deformation of a magnesium alloy investigated by the acoustic emission technique. Journal of Alloys and Compounds 378, 202–206 (2004).
 9.
Dobron, P. et al. Acoustic emission study of the mechanical anisotropy of the extruded AZ31 alloy. International Journal of Materials Research 100, 888–891 (2009).
 10.
Dobron, P., Chmelik, F., Bohlen, J., Letzig, D. & Kainer, K. U. Acoustic emission analysis of extruded AZ31 with varying grain size. Kovove MaterialyMetallic Materials 43, 193–201 (2005).
 11.
Bohlen, J. et al. Orientation effects on acoustic emission during tensile deformation of hot rolled magnesium alloy AZ31. Journal of Alloys and Compounds 378, 207–213 (2004).
 12.
Bohlen, J. et al. The effect of grain size on the deformation behaviour of magnesium alloys investigated by the acoustic emission technique. Advanced Engineering Materials 8, 422–427 (2006).
 13.
Lu, Y., Gharghouri, M. & Taheri, F. Effect of texture on acoustic emission produced by slip and twinning in AZ31B magnesium alloy  part II: clustering and neural network analysis. Nondestructive Testing and Evaluation 23, 211–228 (2008).
 14.
Li, Y. & Enoki, M. Twinning behavior of pure magnesium quantitatively investigated by acoustic emission. Materials Science and Engineering: A 536, 8–13 (2012).
 15.
Zaiser, M. & Seeger, A. In Dislocations in Solids Vol. Volume 11 Dislocations in Solids (eds Nabarro, F. R. N. & Duesbery, M. S.) Ch. 56, 1–100 (Elsevier 2002).
 16.
Miguel, M. C., Vespignani, A., Zapperi, S., Weiss, J. & Grasso, J. R. Intermittent dislocation flow in viscoplastic deformation. Nature 410, 667–671 (2001).
 17.
Vinogradov, A., Danyuk, A. V., Merson, D. L. & Yasnikov, I. S. Probing elementary dislocation mechanisms of local plastic deformation by the advanced acoustic emission technique. Scripta Materialia 151, 53–56 (2018).
 18.
Vinogradov, A., Yasnikov, I. S. & Estrin, Y. Stochastic dislocation kinetics and fractal structures in deforming metals probed by acoustic emission and surface topography measurements. Journal of Applied Physics 115, 233506 (2014).
 19.
Vinogradov, A., Vasilev, E., Merson, D. & Estrin, Y. A Phenomenological Model of Twinning Kinetics. Advanced Engineering Materials 19, 1600092 (2017).
 20.
Vinogradov, A. et al. On the limits of acoustic emission detectability for twinning. Materials Letters 183, 417–419 (2016).
 21.
Richeton, T., Weiss, J. & Louchet, F. Breakdown of avalanche critical behaviour in polycrystalline plasticity. Nature Materials 4, 465–469 (2005).
 22.
Richeton, T., Weiss, J. & Louchet, F. Dislocation avalanches: Role of temperature, grain size and strain hardening. ACTA MATERIALIA 53, 4463–4471 (2005).
 23.
Lebyodkin, M. A. et al. Role of superposition of dislocation avalanches in the statistics of acoustic emission during plastic deformation. Physical Review E 88, 042402 (2013).
 24.
Lebyodkin, M. A. et al. On the similarity of plastic flow processes during smooth and jerky flow: Statistical analysis. Acta Materialia 60, 3729–3740 (2012).
 25.
Shashkov, I. V. et al. Acousticemission study of intermittency of plastic flow during twinning and dislocation glide. Acta Phys Pol A 122, 430–434 (2012).
 26.
Vinogradov, A. & Leksovskii, A. Acoustic Emission in Amorphous Metals. Mater. Sci. Forum 210–213, 549–556 (1996).
 27.
Kovács, Z. et al. Statistical analysis of acoustic emission events in torsional deformation of a Vitreloy bulk metallic glass. Acta Materialia 70, 113–122 (2014).
 28.
Manthei, G. Application of the cluster analysis and time statistic of acoustic emission events from tensile test of a cylindrical rock salt specimen. Engineering Fracture Mechanics (2018).
 29.
Scholz, C. H. M. Microfractures, aftershocks, and seismicity. Bull. Seismol. Soc. Am. 58, 1117–1130 (1968).
 30.
Surkov, V. V. & Hayakawa, M. ULF geomagnetic perturbations due to seismic noise produced by rock fracture and crack formation treated as a stochastic process. Physics and Chemistry of the Earth 31, 273–280 (2006).
 31.
Parsons, T. & Geist, E. L. Were Global M ≥ 8.3 Earthquake Time Intervals Random between 1900 and 2011? Bulletin of the Seismological Society of America 102, 1583–1592 (2012).
 32.
Sornette, D. & Utkin, S. Limits of declustering methods for disentangling exogenous from endogenous events in time series with foreshocks, main shocks, and aftershocks. Physical Review E 79, 061110 (2009).
 33.
Barani, S. et al. Longrange dependence in earthquakemoment release and implications for earthquake occurrence probability. Scientific Reports 8, 5326 (2018).
 34.
Hawkes, A. G. Spectra of some selfexciting and mutually exciting point processes. Biometrika 58, 83–90 (1971).
 35.
Cox, D. R. & Isham, V. Point processes. (Chapman and Hall, 1980).
 36.
Minkova, L. D. IPólya Process and Applications. Communications in Statistics  Theory and Methods 40, 2847–2855 (2011).
 37.
Capolungo, L., Marshall, P. E., McCabe, R. J., Beyerlein, I. J. & Tomé, C. N. Nucleation and growth of twins in Zr: A statistical study. Acta Materialia 57, 6047–6056 (2009).
 38.
Wang, J., Hirth, J. P. & Tomé, C. N. Twinning nucleation mechanisms in hexagonalclosepacked crystals. Acta Materialia 57, 5521–5530 (2009).
 39.
Bowden, F. P. & Cooper, R. E. Velocity of Twin Propagation in Crystals. Nature 195, 1091–1092 (1962).
 40.
Máthis, K. et al. Effect of the loading mode on the evolution of the deformation mechanisms in randomly textured magnesium polycrystals – Comparison of experimental and modeling results. International Journal of Plasticity 72, 127–150 (2015).
 41.
Drozdenko, D. et al. Investigating a twinning–detwinning process in wrought Mg alloys by the acoustic emission technique. Acta Materialia 110, 103–113 (2016).
 42.
Drozdenko, D., Čapek, J., Clausen, B., Vinogradov, A. & Máthis, K. Influence of the solute concentration on the anelasticity in MgAl alloys: A multipleapproach study. Journal of Alloys and Compounds 786, 779–790 (2019).
 43.
Neuhäuser, H. Collective micro shear processes and plastic instabilities in crystalline and amorphous structures. International Journal of Plasticity 9, 421–435 (1993).
 44.
Shashkov, I. V., Lebyodkin, M. A. & Lebedkina, T. A. Multiscale study of acoustic emission during smooth and jerky flow in an AlMg alloy. Acta Materialia 60, 6842–6850 (2012).
 45.
Bohlen, J. et al. On the influence of the grain size and solute content on the AE response of magnesium alloys tested in tension and compression. Materials Science and Engineering: A 462, 302–306 (2007).
 46.
Čapek, J. et al. Study of the loading mode dependence of the twinning in random textured cast magnesium by acoustic emission and neutron diffraction methods. Materials Science and Engineering: A 602, 25–32 (2014).
 47.
Newman, R. C., Shahrabi, T. & Sieradzki, K. Filminduced cleavage of alphabrass. Scripta Metallurgica 23, 71–74 (1989).
 48.
Baró, J., Planes, A., Salje, E. K. H. & Vives, E. Fracking and labquakes. Philosophical Magazine 96, 3686–3696 (2016).
 49.
Kocks, U. F. & Westlake, D. G. Importance of twinning for ductility of hcp polycrystals. Transactions of the Metallurgical Society of Aime 239, 1107–& (1967).
 50.
Vinogradov, A., Orlov, D., Danyuk, A. & Estrin, Y. Deformation mechanisms underlying tension–compression asymmetry in magnesium alloy ZK60 revealed by acoustic emission monitoring. Materials Science and Engineering: A 621, 243–251 (2015).
 51.
Vinogradov, A., Vasilev, E., Linderov, M. & Merson, D. In situ observations of the kinetics of twinning–detwinning and dislocation slip in magnesium. Materials Science and Engineering: A 676, 351–360 (2016).
 52.
Takeda, R., Kaneko, Y., Merson, D. L. & Vinogradov, A. Cluster analysis of acoustic emissions measured during deformation of duplex stainless steels. Materials Transactions 54, 532–539 (2013).
 53.
Vinogradov, A., Lazarev, A., Linderov, M., Weidner, A. & Biermann, H. Kinetics of deformation processes in highalloyed cast transformationinduced plasticity/twinninginduced plasticity steels determined by acoustic emission and scanning electron microscopy: Influence of austenite stability on deformation mechanisms. Acta Materialia 61, 2434–2449 (2013).
 54.
Rasmussen, J. G. Temporal point processes: the conditional intensity function, http://people.math.aau.dk/~jgr/teaching/punktproc11/tpp.pdf (2009).
 55.
Daley, D. J. & VereJones, D. Introduction to the theory of point processes. (Springer, 2008).
 56.
Hawkes, A. G. & Oakes, D. A Cluster Process Representation of a SelfExciting Process. Journal of Applied Probability 11, 493–503 (1974).
 57.
Hawkes, A. G. Hawkes processes and their applications to finance: a review. Quantitative Finance 18, 193–198 (2018).
 58.
Zhang, J., Xi, G., Wan, X. & Fang, C. The dislocationtwin interaction and evolution of twin boundary in AZ31 Mg alloy. Acta Materialia 133, 208–216 (2017).
 59.
Christian, J. W. & Mahajan, S. Deformation twinning. Progress in Materials Science 39, 1–157 (1995).
 60.
Yu, Q. et al. Twintwin interactions in magnesium. Acta Materialia 77, 28–42 (2014).
 61.
Capolungo, L., Beyerlein, I. J., Kaschner, G. C. & Tomé, C. N. On the interaction between slip dislocations and twins in HCP Zr. Materials Science and Engineering: A 513–514, 42–51 (2009).
 62.
Roberts, E. & Partridge, P. G. The accommodation around {1012} 〈1011〉 twins in magnesium. Acta Metallurgica 14, 513–527 (1966).
 63.
Mahajan, S. & Chin, G. Y. The interaction of twins with existing substructure and twins in cobaltiron alloys. Acta Metallurgica 22, 1113–1119 (1974).
 64.
Arul Kumar, M., Kanjarla, A. K., Niezgoda, S. R., Lebensohn, R. A. & Tomé, C. N. Numerical study of the stress state of a deformation twin in magnesium. Acta Materialia 84, 349–358 (2015).
 65.
Beyerlein, I. J., McCabe, R. J. & Tomé, C. N. Effect of microstructure on the nucleation of deformation twins in polycrystalline highpurity magnesium: A multiscale modeling study. Journal of the Mechanics and Physics of Solids 59, 988–1003 (2011).
 66.
Cheng, J., Shen, J., Mishra, R. K. & Ghosh, S. Discrete twin evolution in Mg alloys using a novel crystal plasticity finite element model. Acta Materialia 149, 142–153 (2018).
 67.
Guo, Y., Abdolvand, H., Britton, T. B. & Wilkinson, A. J. Growth of {112^{−}2} twins in titanium: A combined experimental and modelling investigation of the local state of deformation. Acta Materialia 126, 221–235 (2017).
 68.
Basu, I., Fidder, H., Ocelík, V. & De Hosson, J. T. M. Local stress states and microstructural damage response associated with deformation twins in hexagonal close packed metals. Crystals 8, 1–15 (2018).
 69.
Culbertson, D., Yu, Q. & Jiang, Y. In situ observation of crossgrain twin pair formation in pure magnesium. Philosophical Magazine Letters, 1–8 (2018).
 70.
Kumar, M. A., Beyerlein, I. J., Lebensohn, R. A. & Tomé, C. N. Modeling the effect of neighboring grains on twin growth in HCP polycrystals. Modelling and Simulation in Materials Science and Engineering 25, 064007 (2017).
 71.
Nervo, L., King, A., Fitzner, A., Ludwig, W. & Preuss, M. A study of deformation twinning in a titanium alloy by Xray diffraction contrast tomography. Acta Materialia 105, 417–428 (2016).
 72.
Yoo, M. H. & Lee, J. K. Deformation twinning in h.c.p. metals and alloys. Philosophical Magazine A 63, 987–1000 (1991).
 73.
Messerschmidt, U. Dislocation dynamics during plastic deformation. (Springer, 2010).
 74.
Seleznev, M. & Vinogradov, A. Note: Highspeed optical imaging powered by acoustic emission triggering. Rev Sci. Instruments 85, 076103 (2014).
 75.
Orlov, D., Raab, G., Lamark, T. T., Popov, M. & Estrin, Y. Improvement of mechanical properties of magnesium alloy ZK60 by integrated extrusion and equal channel angular pressing. Acta Materialia 59, 375–385 (2011).
 76.
Vinogradov, A. & Ueno, H. Method of signal detection, patent of Japan JP4754651, B (2009).
 77.
Agletdinov, E., Pomponi, E., Merson, D. & Vinogradov, A. A novel Bayesian approach to acoustic emission data analysis. Ultrasonics 72, 89–94 (2016).
 78.
Brown, T. C. & Nair, M. G. A simple proof of the multivariate random time change theorem for point processes. Journal of Applied Probability 25, 210214 (2016988).
 79.
Brockwell, P. J. & Davis, R. A. Introduction to time series and forecasting (Springer Texts in Statistics). (SpringerVerlag New York, 2002).
 80.
Nelder, J. A. & Mead, R. A Simplex Method for Function Minimization. The Computer Journal 7, 308–313 (1965).
Acknowledgements
The support from the Ministry of Education and Science of RF through the State Assignment according to the contract No. 11.5281.2017/8.9 is gratefully appreciated.
Author information
Affiliations
Contributions
A.V. devised the concept of this study and wrote the paper, E.A. developed signal processing algorithms, performed data analysis and prepared the figures, D.M. carried out experiments and discussed the results. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Vinogradov, A., Agletdinov, E. & Merson, D. Mechanical Twinning is a Correlated Dynamic Process. Sci Rep 9, 5748 (2019). https://doi.org/10.1038/s41598019423174
Received:
Accepted:
Published:
Further reading

On the longterm correlations in the twinning and dislocation slip dynamics
Materials Science and Engineering: A (2020)

Analysis of kinking and twinning behavior in extruded Mg–Y–Zn alloys by acoustic emission method with supervised machine learning technique
Materials Science and Engineering: A (2019)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.