Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Towards Laser-Textured Antibacterial Surfaces


Escherichia coli and Staphylococcus aureus bacterial retention on mirror-polished and ultrashort pulse laser-textured surfaces is quantified with a new approach based on ISO standards for measurement of antibacterial performance. It is shown that both wettability and surface morphology influence antibacterial behavior, with neither superhydrophobicity nor low surface roughness alone sufficient for reducing initial retention of either tested cell type. Surface structures comprising spikes, laser-induced periodic surface structures (LIPSS) and nano-pillars are produced with 1030 nm wavelength 350 fs laser pulses of energy 19.1 μJ, 1.01 μJ and 1.46 μJ, respectively. SEM analysis, optical profilometry, shear force microscopy and wettability analysis reveal surface structures with peak separations of 20–40 μm, 0.5–0.9 μm and 0.8–1.3 μm, average areal surface roughness of 8.6 μm, 90 nm and 60 nm and static water contact angles of 160°, 119° and 140°, respectively. E. coli retention is highest for mirror-polished specimens and spikes whose characteristic dimensions are much larger than the cell size. S. aureus retention is instead found to be inhibited under the same conditions due to low surface roughness for mirror-polished samples (Sa: 30 nm) and low wettability for spikes. LIPSS and nano-pillars are found to reduce E. coli retention by 99.8% and 99.2%, respectively, and S. aureus retention by 84.7% and 79.9% in terms of viable colony forming units after two hours of immersion in bacterial broth due to both low wettability and fine surface features that limit the number of available attachment points. The ability to tailor both wettability and surface morphology via ultrashort pulsed laser processing confirms this approach as an important tool for producing the next generation of antibacterial surfaces.


The ability to create passive antibacterial surfaces on industrial components has profound implications for human health services and food production1,2,3. To achieve this, an appropriate scalable technology must be identified based on clear parameters for reducing biofouling under real operating conditions. The self-cleaning lotus leaf has inspired attempts to mimic hierarchical micro and nanoscale surface structures responsible for superhydrophobicity and removal of contaminants via the rolling action of individual water droplets, the so-called “lotus effect”4,5,6,7,8. Other approaches have examined surface structures found on insects that promote self-cleaning and direct rupture of bacterial cell membranes9,10,11. Ultrashort pulsed laser irradiation is a strong candidate for producing surfaces of this kind due to the reliability with which nano- and micro-scale features can be created over large areas with a single process12,13,14,15,16. Superhydrophobic and antibacterial laser-textured surfaces have been demonstrated in the literature17,18; however, the relative importance of wettability and morphology in reducing bacterial retention in this context has not always been distinguished. Differentiation of these aspects for laser-textured surfaces is important from a process point of view as the feasibility of upscaling for high throughput is strongly influenced by the choice of process parameters and therefore optimization strategy. The effects of wettability and morphology on bacterial retention in the context of laser-textured surfaces must therefore be more clearly established to provide precise guidelines for future manufacturing of antibacterial surfaces.

The ability of a bacterial cell to remain attached to a surface reflects the nature of non-covalent interactions between the substrate and cell wall functional groups during the initial phases of attachment. According to attachment point theory, organisms smaller than the characteristic surface feature size can achieve higher attachment strength due to the large available contact area and sheltering effect of surface roughness, while those that are not are more limited in their ability to remain in contact with the surface19. Such a representation is based on direct interaction between the substrate and cell wall, where cell stiffness limits its capacity to adapt to very small surface features20,21. Experimental investigations have shown that retention is strongly limited where the spacing between surface features is smaller than the cell size19,22. This effect has been shown to be particularly evident for engineered surfaces with well-defined features and dimensions23. In some cases, fine surface features are more effective at reducing bacterial retention than extremely smooth surfaces, where biofilm formation has been shown to increase for very low roughness24. The preferential alignment of microorganisms to valley and pillar structures demonstrates that cells seek to maximize contact area for improved attachment25,26,27. It is therefore expected that the presence of small features relative to cell size can reduce cell retention by limiting the number of attachment points.

The role of wettability on cell attachment, adhesion and retention has been demonstrated for polymers and impregnated fabrics whose static water contact angle is modified via changes in chemical composition28,29,30. It has been shown that superhydrophobic surfaces produced by aerosol-assisted chemical vapor deposition can reduce Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) cell attachment by up to 79% and 63%, respectively31. Superhydrophobic and superhydrophilic surfaces with identical surface morphology have been shown to create regions of preferential attachment for specific cell types32. Micromonospora purpurea adhesion has also been found to decrease for duplicated dried-gel superhydrophobic surfaces with a static water contact angle of 150° compared to surfaces with the same topography and contact angles in the range 54°–130°33.

In studies relating to laser-treated metallic surfaces, wettability has been shown to be of lesser influence on bacterial retention than surface morphology for certain cell types. Laser-textured titanium surfaces with micro-bumps larger than 10 µm have been shown to favor S. aureus cell attachment despite a static water contact angle of 166°18. Colonization of Pseudomonas aeruginosa has instead been found to diminish under the same conditions. Laser-textured stainless steel surfaces with laser-induced periodic surface structures (LIPSS) of period 0.7 µm yielded contrasting results for E. coli and S. aureus, with bacterial retention decreasing in the former case and increasing in the latter compared to untreated samples with the same wettability17. Reductions in S. aureus have instead been observed for hydrophilic titanium surfaces with LIPSS and nano-pillars34. Recent studies have found that surface roughness, morphology, chemistry and wettability all play a part in E. coli attachment, adhesion and retention on LIPSS produced via picosecond pulsed laser irradiation35,36. These works have also shown that surfaces displaying lowest bacterial adhesion are not necessarily the most hydrophobic. Dependence of bacteria retention on surface structure dimensions has furthermore been demonstrated for fine surface structures produced via direct laser interference patterning (DLIP), irrespective of surface wettability37,38. Though it is clear that wettability plays a role in influencing cell attachment where other properties remain unchanged, adhesion, retention and biofilm formation on laser-treated metallic surfaces with well-defined surface morphology appears to be strongly dependent on cell type and surface structure size.

Ultrashort pulsed laser irradiation is a well-established method for producing changes in surface morphology and wettability on metallic and semi-conductor surfaces. Interference effects between laser radiation and resulting surface plasmon polaritons on time-scales shorter than the electron-phonon relaxation time lead to formation of self-organized LIPSS with surface feature dimensions close to the laser wavelength for low spatial frequency LIPSS and down to one tenth of the wavelength or smaller for high spatial frequency LIPSS12,39. The physical mechanisms responsible for LIPSS have received extensive attention in the literature13. With increasing energy dose, the effects of ablation, heat accumulation and hydrodynamic instability lead to hierarchical micro-scale bumps and spikes with superimposed LIPSS12,15,40,41,42. It has been proposed that ultrashort pulsed laser irradiation of stainless steel also leads to oxygen deficiency in the form of active magnetite, which is initially hydrophilic before becoming hydrophobic over a period of several weeks due to dissociative absorption of carbon dioxide from air43. It has been observed experimentally that this transition can be inhibited by submerging the treated surface in boiling water for 48 hours43. Laser parameters and post-treatment procedures can therefore be tailored to achieve a wide range of surface structures and wettability characteristics that may be appropriate for creating antibacterial surfaces in healthcare and food production machinery.

The present work clarifies factors influencing E. coli and S. aureus retention on laser-textured specimens by quantifying the performance of several representative surface structures and examining the individual effects of wettability, morphology and topography through discrete manipulation and analysis of these properties. Mirror-polished and superhydrophobic laser-textured surfaces with large surface features are firstly produced to demonstrate limitations associated with low surface roughness and low wettability alone. Laser-textured surfaces with fine features of similar size to bacterial cells are then produced with the aim of minimizing available attachment points. Hydrophobic and hydrophilic specimens with the same surface texture are both considered by ageing laser-treated samples in different environments. Bacterial retention is then assessed based on ISO standards for measurement of antibacterial performance and sampling techniques using contact plates and swabs. Tests are performed with upward-facing horizontal specimens and fluid agitation to ensure bacterial cells are continuously brought into contact with the surface during the exposure period and are not limited to the fluid-surface interface44. Wettability, SEM and topography analyses are performed on all specimens to correlate initial bacterial retention with distinct surface properties. The advantages of this approach are two-fold; firstly, the effects of wettability, morphology and topography on bacterial retention are differentiated for laser-textured stainless steel surfaces, allowing emphasis to be placed on development of laser technology and scanning strategies that favor characteristics directly influencing bacterial retention. Secondly, a measurement approach for antibacterial performance is developed based on ISO standards already of widespread use within the food production industry to facilitate direct technology transfer to end-users. Further to demonstrating that both wettability and morphology are fundamental in driving biofilm formation over a wide spectrum of cell types, the present work confirms laser technology as a valid approach for manufacturing the next generation of antibacterial surfaces.

Materials and Methods

Sample preparation

316 L stainless steel samples supplied by LIMDES were employed for all experiments. Specimens were 50 mm (w) × 50 (l) mm × 2 (h) mm in size and mechanically polished by the supplier to an average areal surface roughness (Sa) of 30 nm. Additional polished samples were also utilized directly for bacterial retention tests to assess the effects of low surface roughness on biofilm formation. Control specimens were rolled 316 L stainless steel with an average areal surface roughness of 0.37 µm, chosen to represent present-day practices within the food handling industry and meet current industry standards45.

Laser treatment

Laser irradiation was performed with an Amplitude Systemes Satsuma HP3 laser source with emission wavelength of 1030 nm and pulse duration of 350 fs. The laser output was firstly directed through a polarizer and half-wave plate for fine adjustment of the laser pulse energy, prior to a beam expander to achieve an appropriate beam size. A galvanometric scanning head and a 100 mm focal length f-theta lens were then employed to focus the laser beam on the specimen surface. LIPSS, spikes and nano-pillars were generated over the entire 50 mm × 50 mm surface of each individual specimen utilizing the process parameters given in Table 1, which had been optimized in a previous work40. Specimens were aged in ambient air for 30 days to ensure complete transition from a hydrophilic to a hydrophobic state40,43. An additional set of LIPSS samples was prepared and held in water at 90 °C for 48 hours immediately following laser treatment to achieve a permanent hydrophilic state43.

Table 1 Laser parameters utilized in experiments.

Morphology and topography

All laser-treated samples were analyzed with a scanning electron microscope (SEM) to confirm their morphology and assess the resulting surface structures. Topography measurements were carried out on spikes with a Taylor Hobson Talysurf CCI optical profiler equipped with a 50× objective. This configuration gave a 336 µm × 336 µm sampling area with nominal horizontal and vertical resolutions of 0.4 µm and <1 nm, respectively. Topography measurements were instead carried out on LIPSS and nano-pillars with shear force microscopy (ShFM), a high-resolution non-contact scanning probe technique that was necessary due to the fine surface features of these specimens. The ShFM setup comprised an electrochemically etched tungsten wire with a nominal diameter of 50 nm joined to a quartz tuning fork with adhesive and maintained in oscillation parallel to the sample surface at 32 kHz. A RHK SPM-100 controller and Physik Instrumente P-517.3 three-axis nano-positioner with horizontal and vertical resolutions of 1 nm and 0.1 nm, respectively, were utilized to scan a sampling area of up to 100 µm × 100 µm while maintaining the tip within a few nanometers of the surface. The oscillation amplitude and phase resulting from friction within the air layer between the tip and surface during ShFM were monitored continuously and applied in a feedback loop to measure the profile in a non-contact manner46,47.

Areal topography parameters, including average areal surface roughness (Sa), skewness (Ssk), kurtosis (Sku) and density of peaks (Spd), were calculated in accordance with ISO 2517848 based on the acquired topography data from the optical profiler and ShFM analysis. Sa represents a commonly used parameter to assess the average deviation of the local surface height from the mean plane21. It is known, however, that the average roughness is not sufficient to uniquely describe a surface in relation to bacterial attachment49,50. Ssk and Sku, representing the second and third order moments of the height distribution over the evaluation area, were therefore also determined. Spd is instead defined as the number of peaks per unit surface area. For calculation of this parameter, application of the watershed algorithm was required to segment the surface into hills or motifs. All relevant definitions for calculation of topography parameters are given in ISO 2517848.


Surface wettability was quantified in terms of the static water contact angle and sliding angle51 as measured via the sessile drop method with a Dataphysics Instruments OCA20 goniometer. A water droplet volume of 6 µL and syringe diameter of 310 µm were employed for all tests. Sliding angle measurements were performed with a stationary deposited droplet at a rotation rate of 1 °/s. The sliding angle was taken as the angle at which the droplet completely detached from the surface.

Bacterial retention

E. coli and S. aureus were chosen as representative rod-like gram-negative and spherical gram-positive bacteria strains, respectively. Cell retention tests were performed on three identical 50 × 50 mm samples for all combinations of surface type and bacteria. Additional tests were performed with E. coli on hydrophilic LIPSS that had been held in hot water for 48 hours immediately after laser treatment. Finally, hydrophobic LIPSS subject to prior contamination and sterilization were tested a second time to assess the robustness of the developed treatments. An equal number of control samples of the same size were tested simultaneously in the same bacteria solutions to provide reference values, monitor solution stability and account for possible differences in bacteria density. Control samples had a surface roughness of 0.37 µm, chosen to represent present-day practices within the food handling industry and meet current industry standards for food handling equipment45.

The method employed for quantifying bacterial retention was developed based on ISO 2219652 and ISO 2744753 standards for measurement of antibacterial performance. Samples were ultrasonically cleaned in acetone for 15 minutes before being sterilized in pure ethanol for 10 minutes and dried in a UV hood until all residue was eliminated. E. coli (ATCC 8739) and S. aureus (ATCC 6538 P) colonies supplied by Microbiologics were transferred separately into Nutrient Agar (NA) with inoculation loops and incubated for 24 hours at 37 °C before being transferred into NA and incubated for a further 18 hours. This procedure was performed in line with ISO 27447 to ensure that the bacteria were in an appropriate growth phase and free from environmental stress. The stock was then diluted to N/500 with an optical density of 0.5 to achieve isotonic cell properties and allow transfer from NA to solution. The resulting fluid was transferred into 200 mL sterile containers in which individual samples were submerged and held horizontally with the laser-treated surface facing upwards for two hours at 24 °C. During this period, containers were agitated with a translating mechanical agitator at a frequency of 1.5 Hz and a stroke of 30 mm to ensure bacterial cells were continuously brought into contact with the surface44. The cell density of fluids employed for each set of tests is given in Table 2. Upon completion, samples were held in a vertical position for 120 s to remove excess liquid from the surface. Residual micro-organism numbers were then quantified in line with ISO 18593 for horizontal sampling methods. Orthogonal surface swabs were taken from each sample over an area of 50 × 40 mm, diluted in solution and seeded in NA prior to incubation at 37 °C for 48 hours. Colony forming units per swab (cfu/swab) were then quantified with a colony counter for each sample.

Table 2 Cell density of fluids employed for each set of tests.

Data availability

The datasets generated during and/or analyzed during the current study are available from the corresponding author on reasonable request.


Laser treatment

Laser exposure with the parameters given in Table 1 successfully led to development of spikes, LIPSS and nano-pillars. As reported in the literature, LIPSS and spikes are easily obtained via ultrashort pulsed laser irradiation. The characteristics of LIPSS are strongly dependent on the properties of the incident laser beam, including the polarization orientation and wavelength. Linearly polarized ultrashort laser pulses produce LIPSS that are perpendicular to the polarization orientation. Spikes develop at higher energy dose due to the onset of ablation, heat accumulation effects and hydrodynamic instability12,15,40,41,42. Nano-pillars instead exploit the possibility of modifying LIPSS geometry by varying the polarization type14. Figure 1a presents a CDD camera image of the beam shape obtained with azimuthal polarization (Altechna s-waveplate polarizer). The initial Gaussian beam was converted into a donut shape that produced the surface structure shown in Fig. 1b. LIPSS extended from the center of the beam to the border, perpendicular to the laser light polarization direction (indicated for several positions with arrows). Figure 1c shows a representative line obtained on samples after scanning with this setup at 1 m/s and a repetition rate of 250 kHz. It is possible to observe that the resulting LIPSS have different directions at the edges of the line than at the center. When irradiating several subsequent lines with a specific separation hatch distance (Table 1), the geometric intersection between each set of LIPSS led to the formation of distinct nano-pillars for a given set of process parameters.

Figure 1

(a) Beam shape after s-waveplate polarizer as recorded by CDD camera (b) surface structure produced on steel after irradiation with azimuthal polarized beam and (c) scanned line with azimuthal polarized beam at 250 kHz repetition rate.

Morphology and topography

SEM images and topography maps of the laser-treated surfaces are presented in Figs 2 and 3. Areal surface roughness parameters are given in Table 3 for all tested surfaces, including control and mirror-polished specimens. Large differences in dimensions can be observed between each laser-textured structure type in terms of lateral dimensions, topography and form. The attainment of LIPSS following ultrashort pulsed laser irradiation with linear polarization at low energy dose and spikes at high energy dose is in line with the literature12,15,40,41,42. These characteristics were sought after to directly assess the effects of surface morphology on bacterial retention. Spikes produced at high energy dose were characterized by elongated asperities or homogeneous columnar structures with a peak separation of 20–40 µm and an average areal surface roughness of 8.6 µm. Skewness (−0.10) and kurtosis (2.0) indicated an even height distribution. LIPSS produced at low energy dose were characterized by elongated parallel ridges perpendicular to the laser polarization orientation with a ridge separation of 0.5–0.9 µm. Nano-pillars presented a relatively homogeneous surface with a peak separation of 0.8–1.3 µm. Average areal surface roughness was 90 nm for LIPSS and 60 nm for nano-pillars, marginally higher than mirror-polished specimens (30 nm). Skewness (LIPSS: 0.13, nano-pillars: 0.54) and kurtosis (LIPSS: 2.9, nano-pillars: 3.9) indicated a relatively symmetrical height distribution for LIPSS and a prevalence of sharp peaks for nano-pillars. Average areal surface roughness for control samples was 0.37 µm.

Figure 2

SEM images of laser-treated surfaces: (a) Spikes (left: 1000×, right: 5000×), (b) LIPSS (left: 5000×, right: 50000×), (c) Nano-pillars (left: 5000×, right: 50000×).

Figure 3

Surface topography of laser-treated surfaces: (a) Spikes (acquired with optical profiler), (b) LIPSS (acquired with ShFM) and (c) Nano-pillars (acquired with ShFM).

Table 3 Measured topography parameters for control, mirror-polished and laser-treated surfaces.


After 30 days of ageing in ambient air, spikes were superhydrophobic with a static water contact angle of 160° and a sliding angle of 14°. This outcome is consistent with other works, where a transition from a hydrophilic to a superhydrophobic state has been observed over several weeks following ultrashort pulsed laser irradiation of stainless steel43. The wettability of aged LIPSS and nano-pillars was somewhat higher than spikes, with static contact angles of 119° and 140°, respectively. Water droplet sliding did not take place on these specimens for angles up to 90°. LIPSS and nano-pillars were therefore hydrophobic but not superhydrophobic. The static contact angle of hydrophilic LIPSS, held in water at 90 °C for 48 hours following laser irradiation, was instead 26°. This result is consistent with the findings of Kietzig et al.43, who suggested that oxygen ions from water deactivate active magnetite sites to form hydrophilic iron oxides. All measured wettability data are provided in Table 4.

Table 4 Measured static water contact angle and sliding angle for laser-treated surfaces.

Bacterial retention

The geometric average of normalized residual E. coli and S. aureus bacteria counts are shown in Fig. 4 for all tested surfaces. The developed method based on ISO 22196 and ISO 27447 was effective at quantifying bacterial retention over a diverse range of conditions. Results are normalized against control samples tested under the same conditions; values below unity represent a reduction in bacterial retention compared to present-day practices and values above unity represent a worse outcome. Results are presented on a logarithmic scale to better account for large differences in performance between surface types. Mirror-polished surfaces display strong dependence on bacteria type. These specimens performed worse than untreated samples for E. coli, with cell numbers almost doubling compared to the control samples. The same surface structure instead yielded an 82.4% reduction in S. aureus. Similarly, laser-induced spikes strongly promoted E. coli retention, with an almost three-fold increase in residual bacteria count. The same structure was instead found to reduce S. aureus retention by 69.8%. LIPSS and nano-pillars exhibited low residual bacteria counts for both tested cell types, with very large reductions attained for E. coli. Best performance was achieved with LIPSS, yielding reductions of 99.8% for E. coli and 84.7% for S. aureus. Nano-pillars performed similarly, with reductions of 99.2% and 79.9%, respectively. Hydrophilic LIPSS instead exhibited a 98.5% reduction in E. coli cell numbers but somewhat greater data dispersion. Finally, hydrophobic LIPSS samples subject to a second contamination cycle exhibited a 99.1% reduction in E. coli retention compared to the control samples, indicating a minor reduction in antibacterial performance compared to initial exposure (99.8%) but nonetheless robust behavior.

Figure 4

Geometric average of normalized residual E. coli and S. aureus bacteria counts for mirror-polished and laser-treated surfaces with spikes, LIPSS and nano-pillars. Three variations of LIPSS are presented: hydrophobic specimens contaminated separately with E. coli and S. aureus (“LIPSS”), hydrophilic specimens contaminated with E. coli (“LIPSS H.PHILIC”) and hydrophobic samples contaminated a second time with E. coli (“LIPSS REPEAT”). Values are normalized against residual bacteria counts for untreated control samples (Sa: 0.37 µm) tested under the same conditions, chosen to represent present-day practices within the food handling industry and meet current industry standards for stainless steel surfaces45. Error bars display maximum and minimum measured values.


Morphology and topography

The laser-treated surfaces can be divided into two broad categories based on their morphology (Fig. 2); spikes that present features much larger than bacterial cells (20–40 µm), and LIPSS and nano-pillars that present features similar in size (0.5–0.9 µm and 0.8–1.3 µm, respectively). The density of peaks, Spd, quantified during topography analysis (Table 3), can be considered a simple indicator of the number of available contact points for bacterial cells based on their dimensions. Rod-shaped E. coli, with a diameter of approximately 0.5 µm and a length of approximately 2 µm, occupy approximately 1 µm2/cell. A reduction in the number of contact points is therefore expected for Spd > 1 µm−2. It has been shown that larger structures (Spd < 1 µm−2) lead to a reduction in E. coli coverage54, for which the criterion Spd > 1 µm−2 is a conservative indicator for reducing the number of available attachment points. Spherical S. aureus cells, with a diameter of approximately 0.5 µm, instead occupy approximately 0.25 µm2/cell. A reduction in the number of contact points in this case is therefore expected for Spd > 4 µm−2. Though such values are based purely on geometric considerations and do not account for asymmetry of the cell or surface, they provide approximate threshold values that can be compared with readily measurable topography data. In the case of spikes, the density of peaks is 1.7 × 10−3 µm−2 (Table 3), some three orders of magnitude lower than the threshold value for E. coli. The density of peaks of LIPSS and nano-pillars are instead 1.1 µm−2 and 1.3 µm−2, respectively (Table 3), greater than the threshold value of 1 µm−2 for E. coli but below 4 µm−2 for S. aureus.


The laser-treated surfaces can also be divided in terms of wettability based on the measured static water contact angle and water sliding angle (Table 4); spikes that are superhydrophobic (contact angle of 160° and sliding angle of 14°), LIPSS and nano-pillars that are hydrophobic (contact angles of 118° and 140°, respectively, with no droplet sliding), and LIPSS held in hot water that are hydrophilic (contact angle of 26° with no droplet sliding). Spikes are therefore superhydrophobic but with a large feature size, a configuration chosen to allow assessment of the prevalence of morphology or wettability on cell retention. LIPSS and nano-pillars instead present only moderate water repellency but features that are similar in size to E. coli and S. aureus. Hydrophilic LIPSS present the same morphology as hydrophobic LIPSS but do not display water repellency at all, allowing direct assessment of the influence of wettability on bacterial retention.

Bacterial retention

Dominance of surface morphology over wettability is evident for E. coli, with water repellency playing a very limited role in influencing initial cell retention. This is seen in both the large residual bacteria count for spikes and the relatively minor difference in residual bacteria count between hydrophobic and hydrophilic LIPSS (Fig. 4). It is instead clear that surface morphology strongly influences E. coli retention. LIPSS and nano-pillars, both with a density of peaks above the critical value of 1 µm−2, display marked antibacterial performance, even after a second contamination cycle for LIPSS. Spikes, with a density of peaks well below the critical value, instead perform poorly. Mirror-polished surfaces also perform poorly for E. coli, representing a worse outcome than current industrial practice. These results highlight the importance of surface structure over average surface roughness and hydrophobicity for E. coli. This is consistent with the findings of Epperlein et al.17, who observed a large reduction in cell retention on LIPSS-covered stainless steel surfaces compared to polished specimens.

The response of S. aureus appears to be more strongly influenced by wettability and average surface roughness. In this case, both mirror-polished and laser-induced spikes provide improvements over control samples (Fig. 4), the former achieving relatively large reductions in cell retention. In contrast to E. coli, the superhydrophobicity of spikes may have influenced S. aureus attachment and self-cleaning of the surface. The low surface roughness of mirror-polished samples (Sa of 30 nm) also leads to improvements. Based on these observations, LIPSS and nano-pillars perform well due to both low surface roughness (Sa of 90 nm and 60 nm, respectively (Table 3)) and moderate hydrophobicity. Epperlein et al.17 reported preferential attachment of S. aureus on LIPSS with a static water contact angle of 79°. This apparent difference may have been due to higher wettability and static bacteria cultivation. Fadeeva et al.18 observed increases in S. aureus retention on superhydrophobic laser-treated titanium surfaces with large 10–20 µm features compared to polished samples. These results are consistent with the present study, where laser-induced spikes performed worse than mirror-polished samples. Cunha et al.34 instead observed reductions in S. aureus biofilm formation on LIPSS and nano-pillars compared to polished titanium samples. Similar results were obtained in the present study for LIPSS on stainless steel.


Though the capacity to create passive antibacterial surfaces via ultrashort pulsed laser irradiation has now been demonstrated on several occasions, the underlying mechanisms leading to this behavior have not always been distinct. The introduction of a new approach for evaluating antibacterial performance based on existing ISO standards represents an important step towards a unified approach for comparing and verifying outcomes achieved with new surface treatments and structure types. In the present study, E. coli and S. aureus, chosen to represent gram-negative and gram-positive bacteria strains with dissimilar geometry, are shown to exhibit very different responses to laser-treated surfaces after two hours of immersion in bacterial broth. Retention of the former depends almost exclusively on the relationship between surface morphology and cell dimensions, while that of the latter exhibits dependence on wettability and average surface roughness. Neither very low surface roughness nor superhydrophobicity alone are therefore appropriate for reducing bacterial retention over a wide spectrum of cell types. LIPSS and nano-pillars obtained via ultrashort pulsed laser irradiation have been shown to provide characteristics that are appropriate for both E. coli and S. aureus. Both LIPSS and nano-pillars, comprising fine features similar in size to bacterial cells, limit available attachment points while exhibiting low surface roughness (Sa: 60–90 nm) and moderate hydrophobicity (static water contact angle: 119–140°). It is possible that LIPSS produced with shorter wavelengths, having yet finer features, could potentially improve performance with regards to S. aureus. Further investigation is therefore required into laser-treatment strategies that produce surfaces with smaller features and a density of peaks above 4 µm−2. Near infrared ultrashort pulsed laser irradiation, however, currently remains the most feasible solution and provides improvements over present-day practices. There are still a range of challenges to be addressed, including upscaling to match present-day manufacturing throughput, verification of longevity and wear resistance in real industrial environments, and longer bacterial retention observation times to more accurately reflect long-term biofouling. With appropriate development, however, ultrashort pulsed laser technology is likely to become a strong candidate for high-throughput production of antibacterial surfaces.


  1. 1.

    Leyland, N. S. et al. Highly efficient F, Cu doped TiO2 anti-bacterial visible light active photocatalytic coatings to combat hospital-acquired infections. Scientific Reports 6, 24770 (2016).

    ADS  Article  PubMed  PubMed Central  CAS  Google Scholar 

  2. 2.

    Srey, S., Jahid, I. K. & Ha, S.-D. Biofilm formation in food industries: A food safety concern. Food Control 31(2), 572–585 (2013).

    Article  Google Scholar 

  3. 3.

    Elbourne, A., Crawford, R. J. & Ivanova, E. P. Nano-structured antimicrobial surfaces: From nature to synthetic analogues. Journal of Colloid and Interface Science 508, 603–616 (2017).

    ADS  Article  PubMed  CAS  Google Scholar 

  4. 4.

    Patankar, N. A. Mimicking the lotus effect: influence of double roughness structures and slender pillars. Langmuir 20(19), 8209–8213 (2004).

    Article  PubMed  CAS  Google Scholar 

  5. 5.

    Feng, L. et al. Super-hydrophobic surfaces: from natural to artificial. Advanced Materials 14(24), 1857–1860 (2002).

    Article  CAS  Google Scholar 

  6. 6.

    Cheng, Y.-T. Is the lotus leaf superhydrophobic? Applied Physics Letters 86(14), 144101 (2005).

    ADS  Article  CAS  Google Scholar 

  7. 7.

    Li, Z. et al. Super-hydrophobic silver-doped TiO2 @ polycarbonate coatings created on various material substrates with visible-light photocatalysis for self-cleaning contaminant degradation. Scientific Reports 7, 42932 (2017).

    ADS  Article  PubMed  PubMed Central  CAS  Google Scholar 

  8. 8.

    Ma, J., Sun, Y., Gleichauf, K., Lou, J. & Li, Q. Nanostructure on taro leaves resists fouling by colloids and bacteria under submerged conditions. Langmuir 27(16), 10035–10040 (2011).

    Article  PubMed  CAS  Google Scholar 

  9. 9.

    Linklater, D. P., Juodkazis, S. & Ivanova, E. P. Nanofabrication of mechano-bactericidal surfaces. Nanoscale 9(43), 16564–16585 (2017).

    Article  PubMed  CAS  Google Scholar 

  10. 10.

    Watson, G. S. et al. Insect analogue to the lotus leaf: A planthopper wing membrane incorporating a low-adhesion, nonwetting, superhydrophobic, bactericidal, and biocompatible surface. ACS Applied Materials & Interfaces 9(28), 24381–24392 (2017).

    Article  CAS  Google Scholar 

  11. 11.

    Watson, G. S., Watson, J. A. & Cribb, B. W. Diversity of cuticular micro- and nanostructures on insects: Properties, functions, and potential applications. Annual Review of Entomology 62, 185–205 (2017).

    Article  PubMed  CAS  Google Scholar 

  12. 12.

    Bonse, J., Höhm, S., Kirner, S. V., Rosenfeld, A. & Krüger, J. Laser-induced periodic surface structures – a scientific evergreen. IEEE Journal of Selected Topics in Quantum Electronics 23(3), 9000615 (2017).

    Article  Google Scholar 

  13. 13.

    Gnilitskyi, I. et al. High-speed manufacturing of highly regular femtosecond laser-induced periodic surface structures: Physical origin of regularity. Scientific Reports 7, 8485 (2017).

    ADS  Article  PubMed  PubMed Central  CAS  Google Scholar 

  14. 14.

    Skoulas, E., Manousaki, A., Fotakis, C. & Stratakis, E. Biomimetic surface structuring using cylindrical vector femtosecond laser beams. Scientific Reports 7, 45114 (2017).

    ADS  Article  PubMed  PubMed Central  CAS  Google Scholar 

  15. 15.

    Mincuzzi, G., Gemini, L., Faucon, M. & Kling, R. Extending ultra-short pulse laser texturing over large area. Applied Surface Science 386, 65–71 (2016).

    ADS  Article  CAS  Google Scholar 

  16. 16.

    Long, J. et al. Superhydrophobic surfaces fabricated by femtosecond laser with tunable water adhesion: From lotus leaf to rose petal. ACS Applied Materials & Interfaces 7(18), 9858–9865 (2015).

    Article  CAS  Google Scholar 

  17. 17.

    Epperlein, N. et al. Influence of femtosecond laser produced nanostructures on biofilm growth on steel. Applied Surface Science 418B, 420–424 (2017).

    ADS  Article  CAS  Google Scholar 

  18. 18.

    Fadeeva, E. et al. Bacterial retention on superhydrophobic titanium surfaces fabricated by femtosecond laser ablation. Langmuir 27(6), 3012–3019 (2011).

    Article  PubMed  CAS  Google Scholar 

  19. 19.

    Scardino, A. J., Guenther, J. & de Nys, R. Attachment point theory revisited: The fouling response to a microtextured matrix. Biofouling 24(1), 45–53 (2008).

    Article  PubMed  CAS  Google Scholar 

  20. 20.

    Whitehead, K. A. & Verran, J. The effect of surface topography on the retention of microorganisms. Food and Bioproducts Processing 84(C4), 253–259 (2006).

    Article  Google Scholar 

  21. 21.

    Lazzini, G., Romoli, L., Blunt, L. & Gemini, L. Design and characterization of textured surfaces for applications in the food industry. Surface Topography: Metrology and Properties 5(4), 044005 (2017).

    ADS  Google Scholar 

  22. 22.

    Lorenzetti, M. et al. The influence of surface modification on bacterial adhesion to titanium-based substrates. ACS Applied Materials & Interfaces 7(3), 1644–1651 (2015).

    Article  CAS  Google Scholar 

  23. 23.

    Graham, M. V. & Cady, N. C. Nano and microscale topographies for the prevention of bacterial surface fouling. Coatings 4(1), 37–59 (2014).

    Article  CAS  Google Scholar 

  24. 24.

    Ivanova, E. P. et al. Differential attraction and repulsion of staphylococcus aureus and pseudomonas aeruginosa on molecularly smooth titanium films. Scientific Reports 1, 165 (2011).

    Article  PubMed  PubMed Central  CAS  Google Scholar 

  25. 25.

    Hochbaum, A. I. & Aizenberg, J. Bacteria pattern spontaneously on periodic nanostructure arrays. Nano Letters 10(9), 3717–3721 (2010).

    ADS  Article  PubMed  CAS  Google Scholar 

  26. 26.

    Vasudevan, R., Kennedy, A. J., Merritt, M., Crocker, F. H. & Baney, R. H. Microscale patterned surfaces reduce bacterial fouling-microscopic and theoretical analysis. Colloids and Surfaces B: Biointerfaces 117, 225–232 (2014).

    Article  PubMed  CAS  Google Scholar 

  27. 27.

    Perera-Costa, D. et al. Studying the influence of surface topography on bacterial adhesion using spatially organized microtopographic surface patterns. Langmuir 30(16), 4633–4641 (2014).

    Article  PubMed  CAS  Google Scholar 

  28. 28.

    Arima, Y. & Iwata, H. Effect of wettability and surface functional groups on protein adsorption and cell adhesion using well-defined mixed self-assembled monolayers. Biomaterials 28(20), 3074–3082 (2007).

    Article  PubMed  CAS  Google Scholar 

  29. 29.

    Berendjchi, A., Khajavi, R. & Yazdanshenas, M. E. Fabrication of superhydrophobic and antibacterial surface on cotton fabric by doped silica-based sols with nanoparticles of copper. Nanoscale Research Letters 6, 594 (2011).

    ADS  Article  PubMed  PubMed Central  Google Scholar 

  30. 30.

    Privett, B. J. et al. Antibacterial fluorinated silica colloid superhydrophobic surfaces. Langmuir 27(15), 9597–9601 (2011).

    Article  PubMed  PubMed Central  CAS  Google Scholar 

  31. 31.

    Crick, C. R., Ismail, S., Pratten, J. & Parkin, I. P. An investigation into bacterial attachment to an elastomeric superhydrophobic surface prepared via aerosol assisted deposition. Thin Solid Films 519(11), 3722–3727 (2011).

    ADS  Article  CAS  Google Scholar 

  32. 32.

    Ishizaki, T., Saito, N. & Takai, O. Correlation of cell adhesive behaviors on superhydrophobic, superhydrophilic, and micropattered superhydrophobic/superhydrophilic surfaces to their surface chemistry. Langmuir 26(11), 8147–8154 (2010).

    Article  PubMed  CAS  Google Scholar 

  33. 33.

    Dou, X.-Q. et al. Bioinspired hierarchical surface structures with tunable wettability for regulating bacterial adhesion. ACS Nano 9(11), 10664–10672 (2015).

    Article  PubMed  CAS  Google Scholar 

  34. 34.

    Cunha, A. et al. Femtosecond laser surface texturing of titanium as a method to reduce the adhesion of Staphylococcus aureus and biofilm formation. Applied Surface Science 360(B), 485–493 (2016).

    ADS  Article  CAS  Google Scholar 

  35. 35.

    Rajab, F. H. et al. Production of hybrid macro/micro/nano surface structures on Ti6Al4V surfaces by picosecond laser surface texturing and their antifouling characteristics. Colloids and Surfaces B: Biointerfaces 160, 688–696 (2017).

    Article  PubMed  CAS  Google Scholar 

  36. 36.

    Rajab, F. H. et al. Picosecond laser treatment production of hierarchical structured stainless steel to reduce bacterial fouling. Food and Bioproducts Processing 109, 29–40 (2018).

    Article  CAS  Google Scholar 

  37. 37.

    Helbig, R. et al. The impact of structure dimensions on initial bacterial adhesion. Biomaterials Science 4(7), 1074–1078 (2016).

    Article  PubMed  CAS  Google Scholar 

  38. 38.

    Valle, J. et al. Evaluation of surface microtopography engineered by direct laser interference for bacterial anti-biofouling. Macromolecular Bioscience 15(8), 1060–1069 (2015).

    Article  PubMed  CAS  Google Scholar 

  39. 39.

    Bonse, J. & Krüger, J. Femtosecond laser-induced periodic surface structures. Journal of Laser Applications 24(4), 042006 (2012).

    ADS  Article  CAS  Google Scholar 

  40. 40.

    Gemini, L., Faucon, M., Romoli, L. & Kling, R. High throughput laser texturing of super-hydrophobic surfaces on steel. Proc. SPIE 10092 (2017).

  41. 41.

    Fraggelakis, F., Mincuzzi, G., Lopez, J., Manek-Hönninger, I. & Kling, R. Texturing metal surface with MHz ultra-short laser pulses. Optics Express 25(15), 18131 (2017).

    ADS  Article  PubMed  Google Scholar 

  42. 42.

    Tsibidis, G. D., Fotakis, C. & Stratakis, E. From ripples to spikes: A hydrodynamical mechanism to interpret femtosecond laser-induced self-assembled structures. Physical Review B 92(4), 041405(R) (2015).

    ADS  Article  CAS  Google Scholar 

  43. 43.

    Kietzig, A.-M., Hatzikiriakos, S. G. & Englezos, P. Patterned superhydrophobic metallic surfaces. Langmuir 25(8), 4821–4827 (2009).

    Article  PubMed  CAS  Google Scholar 

  44. 44.

    Graham, M. V., Mosier, A. P., Kiehl, T. R., Kaloyeros, A. E. & Cady, N. C. Development of antifouling surfaces to reduce bacterial attachment. Soft Matter 9, 6235–6244 (2013).

    ADS  Article  CAS  Google Scholar 

  45. 45.

    Hofmann, J. et al. Hygienic design principles in EHEDG Guidelines (European Hygienic Engineering and Design Group, 2018).

  46. 46.

    Karrai, K. & Tiemann, I. Interfacial shear force microscopy. Physical Review B 62(19), 13174 (2000).

    ADS  Article  CAS  Google Scholar 

  47. 47.

    Tantussi, F. et al. Shear-force microscopy investigation of roughness and shape of micro-fabricated holes. Precision Engineering 41, 32–39 (2015).

    Article  Google Scholar 

  48. 48.

    ISO 25178 Geometrical product specifications (GPS) – Surface texture: Areal (International Organization for Standardization, 2016).

  49. 49.

    Crawford, R. J. et al. Surface topographical factors influencing bacterial attachment. Advances in Colloid and Interface Science 179-182, 142–149 (2012).

    Article  PubMed  CAS  Google Scholar 

  50. 50.

    Goodhand, M. N. et al. The limitations of using “Ra” to describe surface roughness. Journal of Turbomachinery 138(10), 101003 (2016).

    Article  Google Scholar 

  51. 51.

    Zimmermann, J., Seeger, S. & Reifler, F. A. Water shedding angle: a new technique to evaluate the water-repellent properties of superhydrophobic surfaces. Textile Research Journal 79(17), 1565–1570 (2009).

    Article  CAS  Google Scholar 

  52. 52.

    ISO 22196 Measurement of antibacterial activity on plastics and other non-porous surfaces (International Organization for Standardization, 2011).

  53. 53.

    ISO 27447 Fine ceramics (advanced ceramics, advanced technical ceramics) – Test method for antibacterial activity of semi-conducting photocatalytic materials (International Organization for Standardization, 2009).

  54. 54.

    Lu, N. et al. Fabrication of PDMS surfaces with micro patterns and the effect of pattern sizes on bacteria adhesion. Food Control 68, 344–351 (2016).

    ADS  Article  CAS  Google Scholar 

Download references


This project has received funding from the European Union’s Horizon 2020 Research and Innovation Programme under Grant Agreement No. 687613. The authors would like to thank Alessandra Carletti (Artest – Laboratori e Servizi – S.p.A.) for her assistance in developing and performing the bacterial adhesion tests.

Author information




A.L., L.G., L.R. and G.L. contributed equally to the scientific discussions, writing and revision of the manuscript. A.L. performed SEM, optical profiler and wettability analyses, and oversaw bacterial adhesion tests. L.G. developed and performed laser texturing strategies. L.R. oversaw development of the experimental protocol for bacterial adhesion tests. G.L. and F.F. performed ShFM analyses and processed all topographical data. L.R., M.F., R.K. directed the research.

Corresponding author

Correspondence to Adrian H. A. Lutey.

Ethics declarations

Competing Interests

The authors declare no competing interests.

Additional information

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Lutey, A.H.A., Gemini, L., Romoli, L. et al. Towards Laser-Textured Antibacterial Surfaces. Sci Rep 8, 10112 (2018).

Download citation

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing