Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

# Electrical Conductivity Distribution in Detonating Benzotrifuroxane

An Author Correction to this article was published on 01 August 2018

## Abstract

Electrical conductivity profile behind the detonation front in the benzotrifuroxane (BTF) was measured using high-resolution technique. BTF is a peculiar high explosive which is completely hydrogen-free: its molecular formula is C6N6O6. Results are compared with the conductivity distributions in detonating hexogen (RDX, C3H6N6O6) and triaminotrinitrobenzene based explosive (TATB, C6H6N6O6). The conductivity in BTF was found to be similar to that observed in the common explosives which contain hydrogen. Thus, the contribution of hydrogen (e.g., ions produced by the dissociation of water) in the conductivity is minor, both in the reaction zone and in the final detonation products. The characteristics of the conductivity profiles generally support the idea of contact conductivity through the connected structures of carbon particles formed in the detonation wave.

## Introduction

Benzotrifuroxane is a powerful high explosive with several important features which might affect the electrical conductivity of the detonating explosive. Thus, a study of the conductivity distribution in the detonation of BTF is of certain interest.

One possible mechanism of rather high electrical conductivity in explosion was suggested by Dremin,Yakushev and Antipenko1,2. They pointed out that the most typical detonation product is water. Dissociation of water enhanced by the extreme parameters of detonation might produce ions which are regarded as main charge carriers. BTF molecule does not contain hydrogen, therefore water is absent in the detonation products. According to the ionic hypothesis, the conductivity in BTF should be essentially different from that in more common explosives which contain hydrogen.

A number of thermodynamic calculations report quite high detonation temperature in BTF (4900 K3, 5700 K4). However, recent measurements5 demonstrated a lower value (about 4100 K). Given the significant discrepancy between the theory and the experiments, the actual temperature may have some intermediate value, higher than that measured in other explosives, which might affect the conductivity distribution.

Finally, an important detonation product is solid carbon. A broad range of explosives was studied in this connection and many different structures were found (amorphous carbon, diamond, onion-like structures, filaments), with typical size of several nanometers6,7,8,9,10,11. The carbon particles formed in the detonation of BTF are much larger and they have rather complex inner structure. The carbon grains found in the detonation products of TATB, TNT/RDX 50/50 and BTF12 are compared in Figs 1, 2 and 3. The content of carbon in the source molecules of TATB and BTF is about the same, but the solid product differs both in size and in form. For BTF, the solid particles are large (from tens to hundreds of nanometers) and more or less spherical. For TATB, the characteristic diameter is under 20 nm, and one can see rather long fibers. Finally, for TNT/RDX mixture, the particles are still smaller, several nm in diameter, and mostly compact. A certain part of the solid product of TNT/RDX composition consists of the carbon which came from RDX molecules, so Fig. 2 is to some extent representative as illustration of RDX solid residuum. More electronic microscopy data can be found in http://ancient.hydro.nsc.ru/srexpl/detcarbon/index.html.

Authors of work13 suggested that the pecularities of the solid carbon produced by BTF are the consequence of high detonation temperature which may correspond to the liquid state at the phase diagram of carbon14,15. According to work16, large particles are formed owing to the absence of hydrogen. The conductivity profile might reflect these factors because the conductivity in the detonation wave depends strongly on the carbon content17,18,19,20.

In this paper, the measurements of electrical conductivity distribution in the detonating BTF are presented. BTF is a powerful explosive which contains 28.6 mass percent of carbon. The oxygen balance of BTF is −38.1%, while for TATB it is −55.8% and for RDX −21.6%. Results obtained with BTF are compared with those measured in other explosives.

## Elecrtical Conductivity Measurements

The experimental procedures are described in detail in works21,22. Here, merely short description is presented. The explosive was pressed into a massive coaxial copper cell (Fig. 4). The outer electrode consisted of two parts 1 and 2 coupled with the thread connection. The central electrode 3 was mounted in the polymethyl methacrylate plug 4, supported by the hollow bolt 5. The charge diameter was b = 8 mm, and the diameter of the inner electrode was c = 2 mm. Toroidal coil 7 placed within the cavity formed in the outer electrode served as the conductivity gauge. Thin slit which connected the cavity with the coaxial was fixed by the dielectric layer 6 (0.3 mm thick for bulk density and 0.6 mm for pressed explosive).

BTF was pressed by equal portions whose masses corresponded to desired density. The length of each increment (5 mm) was controlled by special washers. Low density charges (1.1 g/cm3) were prepared by pouring 2.5 mm explosive portions into the coaxial, with slight compaction by the fixed weight. The experimental records demonstrate acceptable level of uniformity.

The charge was initiated through the axial channel in the PMMA stopper 8, filled with RDX. The constant feeding current I was supplied by the capacitor through the ballast resistor. The shunt Rs was connected in parallel with the cell. The feeding voltage V(t) and the gauge signal U(t) were measured. The conductivity at the slit plane is roughly proportional to the coil signal:

$$\sigma (x)=\frac{\mathrm{ln}(b/c)U(t)}{2\pi DMV(t)}\,\mathrm{.}$$

Here, x = Dt is the distance the detonation front moved after the slit at a time t, D is the detonation velocity, V is the voltage between the cell electrodes, M is the mutual inductance between the gauge contour and the surrounding cavity. Actually, the signal U(t) was corrected to eliminate the distortion caused by the coil inductance. The spatial resolution was estimated to be about a quarter of the width of a slit 621,22. The instrumental error was estimated to be below 12%. Three shots were performed for each density of the BTF. Detailed description of the method and an animation illustrating the measurement can be found in supplementary materials.

Typical experimental record is shown in Fig. 5. The negative U peak at t = 34.8 μs is induced by the starting cell current as the detonation wave reaches the central electrode. At the same moment, the voltage V falls down to the almost constant operating level (which indicates a good uniformity of the charge). The main signal U of positive polarity starts at about 37.5 μs. At 40 μs, the detonation wave reaches the end of the charge.

It was demonstrated earlier23,24 that the width of the conductivity peak at bulk initial density depends on the dispersity of the explosive. For the present experiments, characteristic grain size was around 150 μm. The photographs of the BTF powder are shown in Fig. 6. Naturally, at higher density (after pressing) the initial grains are destroyed and fine grained structure is formed.

## Results

The effect of initial density on the conductivity is shown in Fig. 7. As for all other explosives peak conductivity increases with density. For all densities, the conductivity profile starts with the sharp peak, which presumably corresponds to the chemical reaction zone. After the peak, lower conductivity is observed in the Taylor wave. At ρ = 1.1 g/cm3, this residual conductivity is much lower than that in dense charges.

Experimental data are reported in the Table 1. Here, ρ is the initial density in g/cm3, D is the detonation velocity in km/s, σmax is the peak conductivity in Ohm−1 cm−1, and τ is the duration of the peak in ns.

The procedure of determining the peak duration (the same as that used in works21,22) is illustrated in Fig. 7 for ρ = 1.1 g/cm3. Note that for any given density, higher σmax corresponds to shorter peak duration τ. Apparently, this correlation indicates distortion of the detonation front because of the charge non-uniformity. A slight inclination of the front, e.g. for 1 or 2 degrees, can extend the peak for 15–30 ns, with corresponding decrease of σmax. Thus, the minimal values of τ are the most reliable, so the reaction time in BTF can be estimated as 40 ns. At ρ = 1.8 g/cm3, maximal value of 20.5 Ohm−1 cm−1 was obtained. This value is similar to the data measured for other high explosives22,23,25,26,27,28.

It was found that in high density shots, the drop of the voltage V(t) after the contact of the detonation front with the central electrode was not monotonous. Instead, the transition to the new level of voltage was accompanied by oscillations of ≈6 ns peak to peak time, which died down after about 100 ns. These oscillations were generated in the low-impedance line (not shown in Fig. 4) which connected the coaxial cell to the shunt Rs. The line was made of two bands of copper foil 20 cm long and 2 cm wide separated by 200 μm plastic; it was used to protect the shunt from destruction (and hence the oscilloscope from dangerous voltage). The line capacitance was about 400 pF and inductances of both line and shunt were around 3 nH. To excite the oscillations, the measuring circuit should be closed fast enough (at least, faster than the period of oscillations). This means that the front of the conductivity profile in BTF is rather steep and the region of high conductivity is quite close to the detonation front (not more than 50 μm distance). Other explosives studied earlier do not exhibit such behavior because of more gradual increase of the conductivity profile.

## Discussion

Conductivity profiles in BTF are compared with those measured in RDX21,29 and TATB30 in Fig. 8. For all explosives, the profiles start with a distinct peak. It is reasonable to relate this peak to the reaction zone, as shown in works22,28,31. For instance, one can see that the conductivity peak in RDX is the narrowest while in TATB it is wider, in agreement with the expected difference in the reaction dynamics. On the contrary, the flow after the peak is considered to be basically equilibrium one, and the conductivity may depend on the chemical composition of the detonation products and on the thermodynamic parameters. The data presented in Fig. 8 call for discussion of the importance of various factors for the electrical conductivity.

### Role of temperature

The detonation temperature in TATB is 2750 K3, well below than that in BTF (4100 K according to the lowest estimate5). Nevertheless, peak conductivity in TATB is slightly higher than that in BTF. In RDX, the temperature value is intermediate (3600 K3) but the peak conductivity is lower than in both BTF and TATB. Thus, the temperature does not play a significant role, and processes such as thermal ionization of the detonation gases and thermal emission from the solid products are of secondary importance. It was shown earlier in work32 that the temperature effect on the conductivity is weak.

### Role of hydrogen

The electrical conductivity in detonation explosives was associated with the dissociation of water1,2. The water content in the detonation products of the CHNO explosives TNT, RDX, PETN, HMX, TATB is around 20%3. Since the conductivity of water shocked to the typical detonation pressure is $${\sigma }_{{H}_{2}O}\approx 10\,{{\rm{Ohm}}}^{-1}\,{{\rm{cm}}}^{-1}$$33,34, this mechanism could explain the value of conductivity of several Ohm−1 cm−135. A notable fact is that the conductivities of RDX and BTF outside the reaction zone (t > 0.1 μs) are quite close (see Fig. 8). In contrast with RDX, BTF produces no water, thus, contribution of hydrogen ions in chemically equilibrated detonation products is minor at best. The same can be said about the reaction zone. The largest peak is in TATB, in BTF, the conductivity is slightly lower and the lowest value is found in RDX. This means that within the chemical peak, hydrogen and water do not prevail as well, and carbon is clearly much better candidate as the universal source of conductivity.

It should be noted that the authors of the “water-ionic” concept also studied the conductivity of hydrogen free explosive–liquid tetranitromethane CN4O836. They found rather low conductivity within a reaction zone (~0.1 Ohm−1 cm−1) and much lower in the subsequent flow. To explain the results, dissociation of NO2 was suggested. Comparison with BTF case makes this idea doubtful because BTF clearly produces less NO2, but its conductivity, even at low density, is about 10 times higher. Again, the conductivity correlates rather with the carbon content, as discussed below.

### Role of carbon

First, let us discuss the post-reaction conductivity. The lower conductivity of BTF as compared with that of TATB may be considered as a confirmation of the contact model suggested by B. Hayes18 in which the grains of free carbon form conducting chains, or nets. There is less free carbon in the detonation products of BTF due to its better oxygen balance (−38.1% vs −55.8% in TATB). Moreover, the larger carbon particles produced in BTF detonation should be less inclined to form contacts and conducting structures. Smaller particles in TATB detonation products can form more contacts and hence provide higher electrical conductivity. The conductivity in RDX is still lower than in BTF, also in agreement with oxygen balance of RDX (−21.6%). So, the conductivity in detonation products is in good correlation with free carbon content and can be explained by the contact model.

All profiles exhibit the sharp conductivity peak. For all explosives discussed in the present work (RDX, BTF, TATB), the peak conductivity correlates with the mass content of carbon in the explosive molecule. For instance, TATB and BTF give close values of σmax, and their carbon mass fractions are almost identical: 0.279 and 0.286, respectively. For RDX, σmax is about two times lower, at carbon mass fraction of 0.162. Role of the total molecular carbon content can be understood assuming that the carbon is released in the reaction zone in over-equilibrium quantities37,38. This view is based on the analysis of the experimental data on destruction of the shocked hydrocarbons. According to39, the molecules of hydrocarbons subjected to the strong shocks break out into condensed carbon and methane. In explosives, one may expect similar process (without methane in the case of BTF) followed by oxidation of these initial products. Thus, the quantity of carbon in the reaction zone may be higher than in detonation products. As a result, the conducting structures should be formed more effectively than in the subsequent flow. Besides, higher density in the reaction zone should further increase the conductivity. Preliminary considerations about the role of molecular carbon content were suggested in work40. A good correlation between the carbon mass fraction and the peak conductivity was shown in work20.

Thus, the results of experiments presented above strongly support the contact model of electrical conductivity of the carbon rich explosives. Formation of the conducting net from fine carbon particles can explain the conductivity both in the reaction zone and in the following flow.

## Conclusions

Despite the exotic chemical composition of BTF, its electrical conductivity distribution is generally similar to that measured in more common explosives (TATB, RDX, HMX, PETN). The conductivity profile starts with a sharp peak about 40 ns wide. The peak conductivity increases with density. The conductivity after the peak (t > 100 ns) is around 1 Ohm−1 cm−1 for high density explosive, and much lower for bulk density. Comparison with other explosives did not reveal any correlation between the temperature and the conductivity.

A sole special feature of BTF is a quite steep conductivity front. The rise time (no more than several ns) is beyond the resolution limit of our method (about 20 ns) and it manifested itself as rapidly damping noise at the start of the work of the experimental cell. As the absence of hydrogen did not produce other qualitative differences, dissociation of water or other compounds containing hydrogen into ions does not make a decisive contribution to the conductivity of common CHNO explosives.

The most probable mechanism of the conductivity in detonating BTF, as for other carbon rich explosives, is formation of conducting nets, or chains, from the carbon particles produced behind the detonation front.

## Change history

• ### 01 August 2018

A correction to this article has been published and is linked from the HTML and PDF versions of this paper. The error has not been fixed in the paper.

## References

1. 1.

Yakushev, V. V. & Dremin, A. N. Electrical conductivity nature in detonation products of condensed explosives. Doklady Academii Nauk SSSR 221, 1143–1144 (1975).

2. 2.

Antipenko, A. G., Dremin, A. N. & Yakushev, V. V. On electrical conductivity zone in detonation of condensed explosives. Doklady Academii Nauk SSSR 225, 1086–1088 (1975).

3. 3.

Tanaka, K. Detonation Properties of Condensed Explosives Computed Using the Kihara-Hikita-Tanaka Equation of State (National Chemical Laboratory for Industry, Tsukuba Research Center. Tsukuba, Japan, 1983).

4. 4.

Kondrikov, B. N. & Sumin, A. I. Equation of state for gases at high pressure. Combustion, Explosives, and Shock Waves 23, 105–113 (1987).

5. 5.

Dolgoborodov, A. Y., Brajnikov, M. A., Makhov, M. N., Safronov, N. E. & Kirilenko, V. G. Detonation parameters of pressed charges of benzotrifuroxane. Combustion, Explosives, and Shock Waves 49, 723–730 (2013).

6. 6.

Lyamkin, A. I. et al. Diamond production from explosives. Doklady Academii Nauk SSSR 302, 611–613 (1988).

7. 7.

Greiner, N. R., Phillips, D., Johnson, J. D. & Volk, F. Diamonds in detonation soot. Nature 333, 440–442 (1988).

8. 8.

Krüger, A. et al. Unusually tight aggregation in detonation nanodiamond: identification and disintegration. Carbon 43, 1722–1730 (2005).

9. 9.

Titov, V. M., Anisichkin, V. F. & Malkov, I. Y. Synthesis of ultradispersed diamond in detonation waves. Combustion, Explosives, and Shock Waves 25, 372–379 (1989).

10. 10.

Bagge-Hansen, M. et al. Measurement of carbon condensation using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene. Journal of Applied Physics 117 (2015).

11. 11.

Ten, K. A. et al. Measurements of SAXS signal during TATB detonation using synchrotron radiation. Proceedings of the 14th International Detonation Symposium, Coeur d’Alene, ID, (Office of Naval Research, Arlington, VA) 387–391 (2010).

12. 12.

Kashkarov, A. O. et al. Transmission electron microscopy and X-ray diffraction studies of the detonation soot of high explosives. Journal of Physics: Conference Series 774, 012072 (2016).

13. 13.

Mal’kov, I. Y. et al. Formation of diamond from the liquid phase of carbon. Combustion, Explosives, and Shock Waves 29, 542–544 (1993).

14. 14.

Viecelli, J. A., Bastea, S., Glosli, J. N. & Ree, F. H. Phase transformations of nanometer size carbon particles in shocked hydrocarbons and explosives. Journal of Chemical Physics 115, 2730–2736 (2001).

15. 15.

Danilenko, V. V. Phase diagram of nanocarbon. Combustion, Explosives, and Shock Waves 41, 460–466 (2005).

16. 16.

Batsanov, S. S. et al. Synthesis and properties of hydrogen-free detonation diamond. Propellants, Explosives, Pyrotechnics 40, 39–45 (2015).

17. 17.

Brish, A. A., Tarasov, M. S. & Tzukerman, V. A. Electrical conductivity of explosion products of condensed explosives. Elektroprovodnost’ produktov vzryva kondensirovannykh vzryvchatykh veshchestv. Zhournal Eksperimental’noi i Teoreticheskoi Fiziki 37, 1543 (1959).

18. 18.

Hayes, B. On the electrical conductivity in detonation products. In Proceeding 4th Symposium (Internat.) on Detonation, White Oak, MD, 595 (1965) 595–601 (1965).

19. 19.

Satonkina, N. P. The dynamics of carbon nanostructures at detonation of condensed high explosives. Journal of Applied Physics 118, 245901 (2015).

20. 20.

Satonkina, N. P. Correlation of electrical conductivity in the detonation of condensed explosives with their carbon content. Combustion, Explosives, and Shock Waves 52, 488–492 (2016).

21. 21.

Ershov, A. P., Satonkina, N. P. & Ivanov, G. M. High-resolution conductivity profile measurements in detonating pressed explosive. Technical Physics Letter 30, 1048–1050 (2004).

22. 22.

Ershov, A. P., Satonkina, N. P. & Ivanov, G. M. Electroconductivity profiles in dense high explosives. Russian Journal of Physical Chemistry B 1, 588–599 (2007).

23. 23.

Ershov, A. P. & Satonkina, N. P. Electrical conductivity distributions in detonating low-density explosives - grain size effect. Combustion and Flame 157, 1022–1026 (2010).

24. 24.

Ershov, A. P. et al. Nonideal detonation regimes in low density explosives. Journal of Applied Physics 119, 075903 (2016).

25. 25.

Loboiko, B. G. & Lubyatinsky, S. N. Reaction zones of detonating solid explosives. Combustion, Explosives, and Shock Waves 36, 716 (2000).

26. 26.

Satonkina, N. P. Duration of the zone of high electrical conductivity at the detonation of RDX of different density. Journal of Physics: Conference Series 894, 012136 (2017).

27. 27.

Dobratz, B. M. & Crowford, P. C. LLNL Explosives Handbook Properties of Chemical Explosives and Explosive Simulants -LLNL University of California (Livermore, California - (UCRL - 52997) (1985).

28. 28.

Orlenk, L.P., editor Explosion Physics [Fizika vzryva], vol. 1 (Moscow: Fizmatlit, 2002).

29. 29.

Ershov, A. P. & Satonkina, N. P. Investigation of the reaction zone in heterogeneous explosives substances using an electrical conductivity method. Combustion, Explosives, and Shock Waves 45, 205–210 (2009).

30. 30.

Satonkina, N. P. & Rubtsov, I. A. Electrical conductivity distribution during detonation of a TATB-based explosive. Technical Physics 61, 142–145 (2016).

31. 31.

Shall, R. Detonation Physics. Collected Works: Physics of High-Speed Processes [Sbornik statey: Fizika bystroprokayushchikh protsessov], vol. 2 (Moscow, Mir Publ., 1971).

32. 32.

Satonkina, N. P. & Medvedev, D. A. The mechanism of carbon nanostructures formation at reaction of organic compounds at high pressure and temperature. AIP Advances 7, 085101 (2017).

33. 33.

Mitchell, A. C. & Nellis, W. J. Equation of state and electrical conductivity of water and ammonia shocked to the 100 GPa (1 Mbar) pressure range. Journal of Chemical Physics 74, 6273–6281 (1982).

34. 34.

Yakushev, V. V., Postnov, V. I., Fortov, V. E. & Yakusheva, T. I. Electrical conductivity of water at quasi-isentropic compression up to 130 GPa. Journal of Experimental and Theoretical Physics 117, 710 (2000).

35. 35.

Satonkina, N. P. Chemical composition of detonation products of condensed explosives and its relationship to electrical conductivity. Journal of Physics: Conference Series 946, 012059 (2018).

36. 36.

Antipenko, A. G., Yakushev, V. V. & Dremin, A. N. Electrical conductivity nature in detonation products of condensed explosives. Combustion, Explosives, and Shock Waves 16, 458–461 (1980).

37. 37.

Anisichkin, V. F. Mechanism of carbon release during detonation decomposition of substances. Combustion, Explosives, and Shock Waves 30, 667–673 (1994).

38. 38.

Anisichkin, V. F. Isotope studies of detonation mechanisms of TNT, RDX, and HMX. Combustion, Explosives, and Shock Waves 43, 580–586 (2007).

39. 39.

Voskoboinikov, I. M. To the conversion of hydrocarbons behind shock fronts. Russian Journal of Physical Chemistry B 5, 697–701 (1986).

40. 40.

Gilev, S. D. & Trubachev, A. M. Study of physical-chemical transformations in detonation wave by the electric conductivity method. In Proceedings of the 12th international Detonation Symposium 240–252 (2002).

## Acknowledgements

The reported study was funded by RFBR according to the research project N 18-03-00227, and partially by RFBR under grant N 18-03-00441.

## Author information

Authors

### Contributions

Satonkina N.P., Ershov A.P., Kashkarov A.O., Rubtsov I.A. carried out the experiments. Satonkina N.P., Ershov A.P., Pruuel E.R. did the analysis of the results. Satonkina N.P., Ershov A.P., Pruuel E.R., Mikhaylov A.L., Spirin I.A., Titova V.B. wrote the paper. Satonkina N.P., Ershov A.P. prepared the illustrations. All authors reviewed the manuscript.

### Corresponding author

Correspondence to Nataliya Satonkina.

## Ethics declarations

### Competing Interests

The authors declare no competing interests.

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

## Rights and permissions

Reprints and Permissions

Satonkina, N., Ershov, A., Kashkarov, A. et al. Electrical Conductivity Distribution in Detonating Benzotrifuroxane. Sci Rep 8, 9635 (2018). https://doi.org/10.1038/s41598-018-28028-2

• Accepted:

• Published:

• ### Dynamics of carbon nanostructures in the benzotrifuroxan detonation

• N P Satonkina
•  & A P Ershov

Journal of Physics: Conference Series (2021)

• ### Observation of Variations in Condensed Carbon Morphology Dependent on Composition B Detonation Conditions

• Joshua A. Hammons
• , Michael H. Nielsen
• , Michael Bagge‐Hansen
• , Lisa M. Lauderbach
• , Ralph L. Hodgin
• , Sorin Bastea
• , Laurence E. Fried
• , Matthew R. Cowan
• , Daniel A. Orlikowski
•  & Trevor M. Willey

Propellants, Explosives, Pyrotechnics (2020)

• ### Elongated conductive structures in detonation soot of high explosives

• Nataliya P. Satonkina
• , Alexander P. Ershov
• , Alexey O. Kashkarov
•  & Ivan A. Rubtsov

• ### Influence of the grain size of high explosives on the duration of a high conductivity zone at the detonation

• Nataliya P. Satonkina

Scientific Reports (2019)

• ### Chemical reaction zone and electrical conductivity profile in detonating high explosives

• Nataliya P. Satonkina
• , Alexander P. Ershov
• , Andrey V. Plastinin
•  & Alexander S. Yunoshev

Combustion and Flame (2019)