Sewable soft shields for the γ-ray radiation

Soft shields are required to protect the human body during a radioactive accident. However, the modulus of most soft shields, such as HDPE and epoxy, is high, thereby making it difficult to process them in wearable forms like gloves and clothes. We synthesized a soft shield based on a hydrogel that is very compliant, stretchable, and biocompatible. The shields were fabricated by integrating γ-ray-shield particles into hydrogels with an interpenetrating network. The soft shields containing 3.33 M of PbO2 exhibited a high attenuation coefficient (0.284 cm−1) and were stretched to 400% without a rupture. Furthermore, the fabricated soft shield can be sewn without a fabric support due to its high energy-dispersion ability. A wearable arm shield for the γ-ray radiation was demonstrated using a direct sewing of the soft-shield materials.

the integration of hydrogels and metal oxides, for which 1 g of sodium alginate and 8 g of acrylamide were dissolved in deionized water (86 wt% water contents) and stored at 4 °C for 3 days to obtain a homogeneous solution. N,N,N′,N′-tetramethylethylenediamine and 0.1 M N,N-methylenebisacrylamide (MBAAm) were added as a crosslinking accelerator for the polyacrylamide and a crosslinker for the polyacrylamide, respectively. A metal-oxide (Fe 2 O 3 , WO 3 , and PbO 2 ) slurry was added into the alginate/acrylamide solution. Then, a solution comprising 0.2 M ammonium persulphate and 1.22 M calcium sulfate was added as a thermal initiator for the polyacrylamide and as an ionic crosslinker for the alginate. A uniformly distributed hydrogel solution was poured into a glass mold and cured with ultraviolet light (with 8 W of power and a 254-nm wavelength) for 1 hr before it was stabilized at room temperature for 2 days. The overall synthesis procedure of the soft shields is shown in Fig. 1.

Results and Discussion
The principle of the soft-shield γ-ray attenuation is shown in Fig. 2(a). The shielding of the γ-ray radiation was primarily induced by an interaction between the electrons in the shield particles and the γ-ray 5,23 . The γ-ray interacted with an atom resulting in the ejection of an electron. The electron then received energy from the γ-ray, and this may induce the secondary ionization of the electron. During the passing of the γ-ray through the shielding material, the γ-ray intensity was decreased. To estimate the ability of the γ-ray shield, it is important to quantify the transmitted γ-ray. The transmission rate and the attenuation coefficient are shown by Equation (1), as follows:

t
where I is the postshielding intensity, I 0 is the incident intensity, μ is an attenuation coefficient, and t is the shielding-material thickness 24 . The mass attenuation coefficient (μ m ) of the compound is shown by Equation (2), as follows: where ρ is the shield-material density, and w i and (μ m ) i are the weight fraction and the mass attenuation coefficient of the ith-constituent element, respectively. For the present work, metal oxides and hydrogel were used as the constituents.
To measure the transmission rate of the passing of the γ-ray through the shielding material, the device that is shown in Fig. 2(b) was customized for the present study. The radiation-source stand was designed with the inner, vertical, and horizontal diameters of 5 mm, 40 mm, and 25 mm, respectively. A γ-ray path from the source was sealed with a lead-metal shield to prevent the radiation scattering toward the detector. The soft shield was placed between the detector and the radiation-source stand. Then, the transmission rate of the soft shields was measured using the previously mentioned device. The radiation source of Cs-137 (0.662 MeV) was manufactured in November 2011, and the activity is 5 μCi. Various soft shields with a thickness of 5 mm were used in the transmission-rate measurements. During the measurements, 800 V of voltage were applied to the detector three times for 600 s each time. Figure 2(c) shows a logarithmic-scale plot of the γ-ray-transmission rates as a function of the soft-shield thickness. The shields contain 3.33 M of each shield particle. The γ-ray-transmission rate was decreased by an interaction between the orbital electrons of the metal oxide and the γ-ray. As shown in Fig. 2(c), the transmission rate was linearly decreased as the soft-shield thickness was increased. In addition, the transmission rate of the soft shields containing lead oxide (PbO 2 ) powder is much lower than that of the other soft shields containing tungsten trioxide (WO 3 ) and ferric oxide (Fe 2 O 3 ) powders, suggesting that as the atomic number of the metal-oxide powder was increased, the interaction probability between the γ-ray and the electron was increased proportionally. Therefore, the soft shield including heavy elements such as PbO 2 powder is more effective than those containing WO 3 and Fe 2 O 3 powders; accordingly, the soft shield including WO 3 powder is more effective than that including Fe 2 O 3 powder.
To obtain the attenuation coefficients for the soft shields including the metal-oxide powders, a slope was fitted with a graph, as shown in Fig. 2(c). The attenuation coefficient of the soft shield for the Cs-137 γ-ray at 0.662 MeV was evaluated using Equation (1). Figure 2(d) shows the attenuation coefficients of the various soft shields. The attenuation coefficient of the pristine soft shield without any metal-oxide powder is 0.216 cm −1 , which is higher than that of the soft shield with metal aluminum (0.2 cm −1 ) 25 . This result is attributed to the high mass attenuation coefficient and the suitable molecular structure of the water for the γ-ray-radiation shielding. In the cases of the soft shields including iron, tungsten, and lead oxides, the attenuation coefficients are 0.229, 0.251, and 0.284 cm −1 , respectively. For the soft shields with a metal oxide containing a high atomic number, the attenuation coefficients of the soft shields were increased. Accordingly, the volume of the heavy-metal particles per unit volume is a primary factor of the radiation-shield ability. Pure metals (i.e., Fe, W, and Pb) will show more favorable attenuation abilities than metal oxides because they contain more metal atoms per unit volume. But metals are unstable in hydrogel because they will be gradually oxidized. Therefore, the investigation of the metal oxides is only regarding the stability of the shield.
Using Equation (2), the attenuation coefficient for the added amount of lead oxide is shown in Fig. 2(e). Analytic calculations were made with values of hydrogel (ρ hydrogel = 1.13 g cm −3 , μ hydrogel = 0.216 cm −1 ) and bulk lead oxide (ρ Pbo2 = 9.38 g cm −3 , μ Pbo2 = 1.020 cm −1 ). The density and attenuation-coefficient measurements of the hydrogel are presented in Fig. 2(d). The lead-oxide attenuation coefficient at 0.662 MeV was calculated using the XCOM (National Institute of Standards and Technology, U.S.A.) program. The theoretical attenuation coefficient of the lead oxide composites at 0.662 MeV was compared with the measured values in Fig. 2(e). The experimental values are in a sound agreement with the theoretical calculations. The attenuation coefficient for the lead oxide composite sharply increased with the increasing of the weight fraction.
The half-value layer (HVL)-it was necessary to reduce the incident intensity of the γ-ray by half using the thickness of the radiation-shielding material-can be calculated using Equation (1), as follows: The effectiveness of the gamma-ray shielding is described in terms of the HVL of the PbO 2 composites, as shown in Fig. 2(f). The lower the HVL value, the more effective the radiation material in terms of the thickness requirement. The increase of the PbO 2 content in the soft shield decreased the HVL.
A tensile test was performed at room temperature using the Instron 3343 tensile machine (Instron, U.S.A.) with a 50 N load cell to determine the mechanical properties of the soft shield for the γ-ray radiation. The specimen size was adjusted to 10.0 × 10.0 × 3 mm 3 , as shown in Fig. 3(a,b). Each soft shield was mounted on the tensile tester and then stretched until a mechanical rupturing occurred with a loading velocity of 6 mm/min. Figure 3(c,d) show the tensile testing of the soft shield containing 3.33 M of lead oxide before and after the stretching up to 150% strain, respectively.
The stress-strain curves of the soft shields with various metal-oxide concentrations are shown in Fig. 3(e,g, and i). Regarding the soft shield including iron oxide, the shape of the stress-strain curve is similar within small differences. It can be seen that as the amounts of the tungsten oxide and lead oxide particles was increased, the ductility of the soft shield was decreased. Figure 3(f,h, and j) show the Young's modulus and the rupture strain of the soft shields with various shield-particle concentrations. As the soft shields contain particle quantities that are more than 3.33 M, the crosslink-formation of the soft shields becomes difficult due to the interaction between the crosslinking polymer and the metal-oxide particles. In the case of the soft shield containing iron oxide, the rupture strain is almost 1000%, and only a slight change is evident regarding the concentration of the shielding particles. In addition, a slight increase of the Young's modulus was observed as the concentration of shielding particle was increased. However, for the soft shields containing WO 3 and lead oxide, the rupture strain decreased as the concentration of the shielding particle was increased. Alternatively, the Young's modulus was increased as the concentration of the shielding particle was increased. It is expected that with a greater inclusion of the shielding particles, the soft shields will become more stiff but less stretchable.
The soft shields containing 0.33 M of lead oxide were irradiated with γ-rays. In order to evaluate the stability of the soft shields to γ-ray, a tensile test was conducted before and after irradiation of the γ-ray. The γ-ray source was Cs-137 and the soft shields were irradiated for 4 hours and 9 hours. The stress-strain curves of the soft shields containing 0.33 M of lead oxide are shown in Fig. 3(k). The shape of the stress-strain curves before and after the γ-ray irradiation is similar. The Young's modulus and rupture strain before and after irradiation of the γ-ray shows little difference within the error range as shown in Fig. 3(l). Therefore, the soft shields are stable in γ-rays.
The soft shields are soft but their mechanical toughness is sufficient for sewing. A stitch test was performed with the soft shield, as shown in Fig. 4(a-c). The specimen size was adjusted to 10.0 × 25.0 × 3 mm 3 , and a 100-µm silk-fiber diameter was sewed at the middle, 5 mm lower than the top surface, as shown in Fig. 4(a,b). The stitch test for the sewed gel was performed with a loading rate of 6 mm/min. As shown in Fig. 4(a,b), the stitched specimen was mounted on the tensile machine and then stretched until a mechanical rupture occurred from the stitching site.
A load-displacement curve of the stitched soft shields is shown in Fig. 4(c). A pristine soft shield was ruptured at the 128 mm displacement, but the soft shield containing 3.33 M lead oxide was ruptured at the 37 mm displacement. But interestingly, the soft shield containing lead oxide was able to withstand a load that is 1.5 times higher than that of the pristine soft shield by only one stitch. Due to the excellent energy dissipation in the soft shields from the interpenetration of the covalently crosslinked polyacrylamide with the ionically crosslinked alginate, a sewing may mean that the shield can withstand high stress concentrations. The soft shield was sewn several times, as shown in Fig. 4(d), and it was stretched with considerable power, as shown in Fig. 4(e); therefore, it is possible that they could provide resilience without the occurrence of a rupture. As shown in Fig. 4(f ), a wearable shield for the γ-ray radiation was simply made. The biocompatibility of the shield is expected to be high because the pristine hydrogel is biocompatible and the metal oxides that have been used in this work are nonreactive in a hydrogel matrix. Furthermore, it is expected that the shield will provide heat protection, since it contains a 51 wt% of water.

Conclusion
A sewable soft shield for radiation was synthesized through an integration of hydrogels and metal oxides. Sewable soft shields with a shielding ability and a wearability are applicable in areas of the nuclear industry such as transportation, the storage of radioactive materials, and the protection of the human body following a radioactive accident. In the case of the soft shields containing 3.33 M of Fe 2 O 3 , WO 3 , and PbO 2 , the attenuation coefficients are 0.229, 0.251, and 0.284 cm −1 , respectively, and they were stretched by more than 400% without the formation of a rupture. The stretchability and energy-dispersion ability of the fabricated soft shield are high so that sewing can be performed. If the soft shield contains greater amounts of metal-oxide particles or higher-atomic-number metals, the attenuation coefficient of the soft shield can be increased because the probability of the interaction between the γ-ray and the electron is increased. The attenuation coefficient can be calculated with the amount of the contained shielding material using analytic calculations, so the control of the attenuation coefficient and the mechanical properties of the soft shield can be achieved by adjusting the contained material and contents. Accordingly, the soft shield can be used as a wearable shield in a radioactive environment, enabling researchers to form a more comprehensive understanding of soft shields, thereby broadening the current soft-shield research and applications for radiation.