The organic and mineralogical heterogeneity in shale at micrometer and nanometer spatial scales contributes to the quality of gas reserves, gas flow mechanisms and gas production. Here, we demonstrate two molecular imaging approaches based on infrared spectroscopy to obtain mineral and kerogen information at these mesoscale spatial resolutions in large-sized shale rock samples. The first method is a modified microscopic attenuated total reflectance measurement that utilizes a large germanium hemisphere combined with a focal plane array detector to rapidly capture chemical images of shale rock surfaces spanning hundreds of micrometers with micrometer spatial resolution. The second method, synchrotron infrared nano-spectroscopy, utilizes a metallic atomic force microscope tip to obtain chemical images of micrometer dimensions but with nanometer spatial resolution. This chemically “deconvoluted” imaging at the nano-pore scale is then used to build a machine learning model to generate a molecular distribution map across scales with a spatial span of 1000 times, which enables high-throughput geochemical characterization in greater details across the nano-pore and micro-grain scales and allows us to identify co-localization of mineral phases with chemically distinct organics and even with gas phase sorbents. This characterization is fundamental to understand mineral and organic compositions affecting the behavior of shales.
Shales are sedimentary rocks predominantly composed of fine grained mineral particles mixed with variable quantities of organic matter (OM), typically 5–20% w/w, including kerogen1. Shale rocks are effective traps and barriers for fluids, including methane and carbon dioxide (CO2), because the mineral and kerogen components form a low-permeability nanoporous network. Understanding the transport properties and reactivity of shale rock during oil and gas production, or during weathering reactions, requires knowledge of the nanoscale composition and mesoscale (nm–to–μm) heterogeneity. An adequate description of shale rock structure, mineralogy and chemistry, however, is currently beyond any single analytical or imaging approach2. Here we show that multiscale infrared spectroscopy and imaging, coupled to a neural network spectral classification algorithm, provides rich details of the chemical heterogeneity of shale.
Fourier transform infrared spectroscopy (FTIR) is a non-destructive method that can identify and quantify both mineral and organic substances. For example, FTIR analysis of bulk shale samples quantified the abundance of eight different minerals in shale samples in good agreement with X-ray diffraction analysis3. FTIR spectroscopy can also quantify measures of kerogen maturation. Specifically, the H/C ratio (A-factor) and O/C ratio (C-factor) derived from FTIR spectroscopy4,5 strongly correlate with elemental ratios obtained from the gaseous combustion method and the vitrinite reflectance value in a large number of shale samples6.
The long wavelengths of infrared light have traditionally limited the spatial resolution of the associated imaging method. Attenuated total reflection (ATR) FTIR microscopy can determine the mineral composition of a shale in two-dimensions but is limited to an approximately 100 μm spatial resolution7, and a recent study provides a considerably better characterization of the interconnected organic matter/mineral network, only limited to a 25 μm resolution8. An improvement of the ATR technique incorporates a large-radius germanium hemispherical crystal as the internal reflective element9,10 (Fig. 1a). The Ge hemisphere increases the numerical aperture of the micro-ATR technique and improves the spatial resolution by the index of refraction of the hemisphere, which is ~4 for Ge. We used the Ge micro-ATR technique coupled to a high-density focal plane array detector (FPA), which allows full spectral images with dimensions of 100 s µm and spatial resolution of detection approaching 1 µm without sample displacement or image distortion11.
An alternative and recently developed technique provides infrared imaging and spectroscopy with nanometer spatial resolution, nearly 1000 times smaller than the limit imposed by diffraction12,13. In this technique, a metallic atomic force microscope (AFM) tip enhances the intensity of infrared light at the near-field of the sample surface, and scattered light that has interacted with the sample is captured by an infrared detector (see Fig. 1b). After demodulating the detector signal at harmonics of the tip oscillation frequency, the near-field signal reveals information about the sample with tip-limited spatial resolution. When combined with a broadband synchrotron source in an asymmetric Michelson interferometer configuration, synchrotron infrared nano-spectroscopy (SINS) can span the mid- and far-IR14. Full spectral images are acquired by raster scanning over the sample surface which limits the throughput and applications, and as a result the 2D chemical image with nanometer resolution became available on a model sample just recently15. Although micro-ATR and SINS are both powerful approaches for microchemical analyses11,16,17, we show below that neither approach alone can provide mesoscale characterization of shale composition. Micron-scale spectroscopy does not permit unambiguous identification of nanoscale phases. Nanoscale spectroscopy cleanly resolves IR signatures of constituents but cannot generate chemical images at the necessary length scales. We show that a machine-learning method, in this case a single-layer neural network, can transfer spectroscopic information between techniques and hence across scales. We illustrate this approach with new insights into the distributions of organics, minerals and, surprisingly, gas-phase sorbents within a gas shale sample.
Results and Discussion
Infrared spectroscopy on bulk mineral standards and shale rock sample
Figure 2 shows the infrared signatures from bulk standard minerals and the shale rock sample in this study. The infrared spectrum of the shale indicates it contains many reference minerals. For example, kaolinite features a strong Si-O stretching vibration at ~1010 cm−1 and a strong Si-O-Al stretch at 1110 cm−1 18, while quartz features a single dominant peak at around 1090 cm−1 from Si-O asymmetric stretch19. Dolomite and related carbonates feature a strong peak at ~1450 cm−1 resulting from the asymmetric stretch of the CO3 anion20. Additional minor peaks at ~1720 cm−1, ~1650 cm−1, ~1400 cm−1 originated respectively from the carbonyl, aromatics and aliphatic groups from the kerogen21. However, the presence of multiple and overlapping spectral features in the bulk spectrum makes the confident identification of different minerals difficult.
Ge micro-ATR FTIR of shale rock
Clearer information on the content and distribution of organic and mineral materials is first obtained using the Ge micro-ATR method. Figure 3 shows 640 µm × 640 µm maps derived from FTIR spectra obtained from micron-scale areas in the cross-section of the shale rock and four spectra from selected locations. These maps (Fig. 3d,e) were reconstructed using the vibrational strengths for selected peak locations after a full-spectrum fitting with a multi-oscillator model. They highlight regions in which silicates, carbonates and organics contribute strong signals, as shown by the distinctive spectra (Fig. 3a) from selected locations within the mapped area. These micron-scale single-pixel data provide IR spectra in which individual contributions can be more clearly distinguished than in the bulk data. Notably, the broad silicate band at ~1000 cm−1 separates into distinct contributions from Si-O bonds in quartz and clays in these selected locations. In addition, different carbonates can be resolved through their contributions at 1390 cm−1 (calcite), 1410 cm−1 (dolomite) and ~1450 cm−1 (aragonite). Moreover, organic-rich area show contributions at ~1650 cm−1 (aromatic) and 1720 cm−1 (carbonyl) that were barely visible in the bulk data.
It is difficult to evaluate the accuracy of the peak fitting method in many locations because the vibrational features are overlapped in most of the mapped area despite micron scale resolution. We sought to apply a standard spectral analysis method, principal component analysis followed by a k-means clustering to the full data set to identify the contributions from individual phases. However, this approach failed to extract distinct and meaningful components (Fig. 4a), because of the mixtures of phases overwhelmingly present within individual micrometer scale pixels.
SINS imaging on shale rock
With the SINS method, much clearer mineralogical and chemical information is obtained. The SINS data (a total of 10,000 spectra) were successfully clustered and could be identified either as one of the mineral references (quartz, carbonate, clay), a strong-scattering class, or an organic-rich class. As illustrated in Fig. 4b, vibrational spectra obtained from single nanoscale pixels now show very close agreement with the data from standards, and the standard deviations of each group of the spectra are fairly narrow, much improved from the results of Fig. 4a. In particular, the SINS spectra allow weaker diagnostic vibrational modes to be detected, including the carbonate C-O out-of-plane bending (~880 cm−1, green curves) and the silicate symmetric Si-O stretch (~800 cm−1, red curves). We can now determine that the carbonate in this sample is mainly dolomite and that the silicate is quartz. Moreover, the precise location of the peak position at 1020 cm−1 (blue curves) indicates the likely existence of Mg-O-Si bonds. These conclusions could not be made from either the bulk or Ge micro-ATR data. There is also a group of spectra with signatures from organic chemicals, shown as cyan curves in Fig. 4b, which will be discussed in detail below.
The SINS data may show spectral evidence of spectral enhancement not observed in Ge-ATR data. First, SINS spectra from some areas contained no or few evident vibrational bands but were dominated by a very broad and strong scattering. This response is typically observed in SINS studies of conductive materials22,23 and hence we infer that these regions contain pyrite. Pyrite does not have any strong vibrational bands in the 800–3000 cm−1 range24 accessible by Ge or SINS and we did not include this mineral as a reference. Pyrite’s spectrum is therefore featureless using the Ge method, but the strong optical scattering signals in SINS were used for mapping this mineral. Note that since pyrite has distinct signatures at ~400 cm−1, a Si- or diamond-ATR method incorporating far-IR detection25 could be used to directly identify the pyrite content in future studies. The electric field enhancement at conductive pyrite surfaces may increase the vibrational signal from associated minerals and organics, and indeed reconstructed chemical maps show an apparent imprint of this enhanced signal, especially visible in the maps reconstructed from the generally weak organic peak (Fig. 4f). Modelling the full tip-sample interaction with recently developed models26 could be used to establish the full influence of this near-field enhancement effect.
In order to confirm our identification of all the minerals, we performed scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) on the same sample surface. The results are summarized in the Supplementary Figures 3 and 4. Although the EDX was not capable of detecting the molecular bonding information as we can with the infrared spectroscopy, the concentration of elements detectable in different locations confirmed the existence of pyrite, indicated by relatively enhanced emission signals of Fe and S co-localized at the same spots, carbonates (Ca and C), silicates (Si and O) and organics (C and O).
Second, energy transfer between closely–spaced vibrational bands can increase the signal from a weak resonance that lies on or near a dominant absorption27. Consistent with this mechanism, organic signatures in the 1200–1400 cm−1 region that lie close to the strong carbonate feature around 1450 cm−1 are overall stronger than for any other curve (Fig. 4b) while the organic signatures around 1650 cm−1 (used for mapping the organic distribution) are significantly weaker.
We constructed chemical maps using the vibrational strengths of selected peaks, and also mapped the high-scattering signal attributed to pyrite (Fig. 4c–f). The chemical maps show that even single morphological structures imaged by the SINS AFM tip (Fig. 4g) are of highly heterogeneous composition even within the mapped 1 μm area.
Classification with neural network
The chemical distribution maps of Figs 3 and 4 are not unbiased interpretations of the data because they are generated by intensities in manually selected peak regions that may contain contributions from different constituents. Moreover, the signal intensity varies significantly, likely due to surface topography, hiding chemical information from regions of low SINS scattering. For improved, unbiased data interpretation we developed a neural network (NNet) model. A large number of spectra in these blue areas included vibrational modes from organic molecules (e.g., 1300, 1350, and 1650 cm−1) as well as small peaks associated with silicate and carbonate (shown in the blue cluster in Figure S1); they are therefore classified as organic-rich. We used this data set, labeled as quartz, clay, carbonate and organic-rich, to train a 10-node NNet and then used the NNet to classify all the spectra in both the SINS for cross-validation and Ge data sets for prediction. We left out the pyrite class in the model because this phase is not detectable using the Ge micro-ATR method. The analysis flowchart is given in Fig. 5a and the predicted mineral distribution images for the nanoscale and microscale data are given in Fig. 5 b and c.
The map showing the classification of the SINS data provides a much more complete analysis of the shale distribution because is removes the intensity variations that are inevitable in the peak-fitting approach. Thus, the areas of low-intensity imaging (blue regions of Fig. 4c–f) are now fully interpreted. This approach also significantly improved the interpretation of the Ge dataset. Notably the chemical map of silicates (Fig. 3b) can be further classified into two maps of quartz and clay respectively in the classification map (Fig. 5c), and their matched locations further validate our model prediction in the microscale data. The classification procedure also helps to eliminate possibly misleading imprints from the near-field enhancement effect of conductive regions (Fig. 4c–f). Figure 5 shows that high-accuracy IR spectrum labeling and classification performed on a dataset with nanoscale spatial dimensions and resolution can be used to interpret a dataset with microscale resolution. This cross-scale molecular analysis method is not limited to IR spectroscopy of shale rock, but could be applied in the other many applications such as hyperspectral remote sensing or live cell imaging.
Kerogen Distribution and Maturity
Two-dimension mineral distribution maps are commonly obtained for shale and other rocks using scanning electron microscopy (SEM) but this approach cannot obtain chemical information on the organic components28,29. Here we show that IR imaging combined with spectral analysis and classification can provide new insights into the relationships between mineral and organic components.
First, we observed evidence of the co-localization of organics with carbonate minerals. Although the Ge and SINS chemical imaging maps both display a highly heterogeneous distribution of organic functional groups, including OM not associated with any mineral phase, both approaches showed OM co-localized with carbonates more than any other mineral. This observation is in accord with the recent Raman/STXM study that found kerogen to associate with carbonates in a Mesozoic gas shale from northern Germany30.
Second, we observe substantial spatial heterogeneity in chemical signatures that have been used in bulk samples to determine kerogen maturity. The ratio of aromatic to aliphatic content (i.e., aromaticity) increases with maturity and with increasing carbon content in coals. Elemental ratios, such as the organic H/C ratio (called the A-factor) and the O/C ratio (C-factor) that quantify kerogen maturity can be measured directly through pyrolysis or indirectly through vitrinite reflectivity or FTIR analysis of bulk kerogen. In Fig. 6a and b we show possibly the first chemical distribution maps for IR-derived proxies for kerogen maturity at a micron scale. These maps show that bulk analyses provide averages over organic inclusions that can exhibit significantly different chemistry and apparent maturity. We find that kerogen with a high C-factor is selectively co-localized with carbonate minerals suggesting a link between organic matter oxidation, CO2 evolution and local precipitation of carbonate minerals. Further calculation using the averaged area values of corresponding peaks yields a C-factor of 0.26 and an A-factor of 0.70, which indicate the bulk material is a type II kerogen. This compares to the smaller values that we derived from the bulk measurement, 0.14 and 0.34 respectively, reflecting better resolved organic content because of the better resolved C-H and carbonyl bonds at high resolution (Figure S2).
Our micro-ATR analysis revealed a signal from molecular CO2 that was associated with the shale rock and not due to atmospheric interference. We generated a CO2 distribution map (Fig. 6c) using the absorbance strength from the antisymmetric CO2 stretching vibrations at 2350 cm−1 and 2360 cm−1. Over 5000 spectra in the map showed detectable CO2 absorption features in a somewhat preferred arrangement along the vertical direction of the image, with the mean of these and single-pixel examples given in Fig. 6d. This observation is in accord with recent studies31,32,33,34 showing that layered silicates in either controlled or natural settings, particularly in swelling clays, can adsorb or intercalate, and retain CO2. However, please note that this spatial correlation with CO2 is not at all unique, as we show in Fig. 3a, which suggests that the CO2 peaks correlates with the features of organics too. We did not observe any signal from methane in this gas shale, indicating CO2 to be higher affinity than CH4 to clay surfaces and interlayers. The infrared signatures of water which is important for shale heterogeneity are in general weak and narrow (e.g the O-H bending mode at ~1650 cm−1), or very broad (e.g. the O-H stretching mode at ~3300 cm−1) in this sample, as shown in Figure S5, so it’s difficult to retrieve its distribution map by fitting the peaks. However, by integrating the total absorbance in the frequency region related to the broadband O-H stretching mode, we were able to reconstruct a somewhat reasonable distribution map (right panel of Figure S5). In general the water concentration is fairly low in our sample, and concentrated in two confined regions. The potential contribution of the O-H bending mode to our observed infrared absorbance peak from organics (as we used in the SINS method) is therefore negligible as we show in the left panel of Figure S5.
We used SINS to reveal the heterogeneous distribution of mineral and organic phases at nanoscale spatial resolution, and showed that a single-layer neural net that is trained using SINS spectroscopy can accurately classify spectra obtained from micron-scale analysis, thereby enabling representative rock areas to be characterized. This cross-scale molecular imaging methodology can be applied to shale rock and any other material with nanoscale organic and inorganic heterogeneity, and a multi-layer neural net, e.g. a convolutional neural network35, could be used to further quantify the pixel-level chemistry. The studies of a gas shale revealed kerogen maturity to be heterogeneous and show selective mineral associations, information on shale diagenesis difficult to obtain through any other non-destructive method. The Ge method will facilitate future studies of the influence of temperature and stress on the chemical and mineralogical structure of shale rock. Moreover, the ability to map the distribution of molecular CO2 adsorbed to clay minerals illustrates the potential for real-time studies of fluid interactions with nanoporous shale rock.
Materials and Methods
We obtained Marcellus shale rock samples from a depth of 6306 feet in a gas-producing zone from a natural gas resource company. Using the infrared spectroscopic method, we determine that these shale samples are of the first type of kerogen with H/C ratio and C/O ratio around 1.2 and 1.1, respectively. The shale sample is rather soft in mechanical strength and we polished the surface across the cleaving lines, and the sample is then mounted on a metal plate by epoxy on the unpolished side.
Standard minerals and their reference spectra
Some of the mineral standards were obtained from Glenn Waychunas at Lawrence Berkeley National Laboratory. The others are a collection by BG at different field sites in North America. Some of them were powdered and those that were not were powdered by a tissuelyzer (Tissuelyzer II, QIAGEN) with a stainless steel ball at 1400 rpm for 10 minutes. The resulted fine powders of minerals were used as infrared standards for feature identification and extraction. The spectra of these mineral powders were obtained on a diamond ATR crystal in an infrared spectrometer (Nicolet IS50, Thermal Fisher Scientific Inc.) with 128 scans.
Infrared Hyperspectral Image Data Acquisition
Ge-hemisphere enhanced imaging
A hemisphere of Germanium with diameter of one inch is used for near-field enhancement of infrared imaging. The infrared light from a globar infrared source is modulated by an interferometer, and then focused through a reflective 15× objective of a microscope (Cary 620 FTIR microscope and Cary 670 Spectrometer, Agilent Technologies) onto the top of the hemisphere. The 15× objective was used for imaging a large field of view, ~700 µm × 700 µm. The flat surface of the hemisphere is in contact with the solid shale sample, and the light from the microscope is further focused through the hemisphere to the flat interface. The reflected light from the solid sample is collected by the Ge hemisphere and then imaged back to a focal-plane array mercury cadmium telluride (MCT) detector (128 × 128 pixels) cooled with liquid nitrogen.
Because of the high refractive index of Ge, ~4, and enhanced collection of the evanescent waves at near-field, this setup allows us to image at very high resolution of around half of the wavelength of the light, ~1 to 4 micrometer in this study. By coupling to a FPA detector with 128 × 128 elements, we can increase the throughput by more than a thousand times than that with a conventional point detector. The further enhancement at near-field allows highly sensitive measurement on the heterogeneous surface on the shale rock sample, otherwise very difficult to collect due to the omnidirectional scattering light from grain boundaries with a far-field setup. During the measurement, the hemisphere’s flat surface is screwed tightly down to the polished surface of the shale sample. Since shale samples are soft in mechanical strength, we believe a very good contact had been maintained during the measurement, which can be proved by the overall satisfactory signal strength throughout the map.
A background image was first collected without sample contact, and then the infrared image of the sample surface was collected. Each image were averaged for 3 minutes, a truly high-throughput imaging method.
The SINS instrument at the Advanced Light Source (ALS) combines the brightness and spectral bandwidth of synchrotron infrared light with the sensitivity and spatial resolution of scattering type, s-SNOM to obtain broadband infrared spectra with AFM tip limited spatial resolution, which is typically less than 25 nm. The instrument is based on a customized atomic force microscope (AFM, Innova, Veeco Instrument Inc.) combined with a modified Fourier Transform infrared spectrometer (FTIR, Nicolet 6700, Thermo-Scientific) in an asymmetric Michelson interferometer configuration. Briefly, half the light from the synchrotron source is transmitted through a 50:50 KBr/Ge beamsplitter and focused on a conductive AFM tip with a parabolic mirror. The back-scattered light is collected by the same parabolic mirror and reflected toward an MCT detector by the beamsplitter. The other half of the incident light is directed toward the moving mirror in the FTIR bench and retro-reflected back to the beamsplitter and onto the detector. Movement of the reference mirror creates an interference signal on the detector and the corresponding interferogram is Fourier-transformed to extract the amplitude and phase spectra of the scattered signal. The AFM tip is operated in non-contact mode and the scattered signal is demodulated at twice the tapping frequency of the tip in order to extract the near-field signal from the far-field background. For the measurements presented here, an area was selected on the same sample that was scanned for the Ge-micro-ATR measurement. Hyperspectral maps were collected with 100 × 100 pixels over an 8 hour period with a step size of 64 nm to create an area map with total dimensions of 6.4 um × 6.4 um. Each pixel contains a broadband infrared spectrum from a ~20 nm spot, which is acquired at 16 cm−1 spectral resolution and averaged for 3 s. A template stripped gold surface was used to collect the background spectrum before mapping on the shale sample. The detailed data process afterward can be found in the reference14.
Data Processing and Analysis
Quantification of spectral intensities in portions of the IR spectra was performed by fitting the full spectra with a series of Lorentzian peaks using the custom software, KFit Pro, written in C++ and compiled with Microsoft Visual Studio 2013. This multi-oscillator fit does not consider any reference spectra and allows images to be reconstructed based upon any fitted peak intensity.
We used standard methods available in the R environment36 for classifying spectra obtained from the micro- and nano-IR. Following baseline correction and data smoothing37, we performed principal component analysis (PCA) and chose the top components that covered 98% or more over the data variance (typically 3 or 4). Subsequently, IR spectra from individual pixels were classified according to their similarity to the components by k-means clustering.
We use R environment for data analysis and machine learning. A number of R packages were used to perform baseline correction and data smoothing, principal component analysis, partial least squared regression (PLSR)38, and neural network (NNET)39.
Neural network model
The spectral classification of nano-IR data provided 4 chemically and mineralogically meaningful example spectra that clustered in distinct branches in PCA space (Figure S1). The data in the last group contained mostly organic and mixed mineral peaks, therefore they concentrated in the center of the PCA plots, and were not used for training to avoid overfitting but labeled as organic-rich in the reconstructed images. We used ~10,000 spectra that were labeled based on the reference data for unsupervised training of a neural network (NNet) model implemented in R. We composed a 10–node NNet with a single hidden-layer which allows us to run the model on a personal computer (16GB memory with one Intel i7-4790 CPU). The spectra were first reduced to contain only 10 uniformly spaced frequency bands by multi-point linear interpolation and then fed into the NNet model as inputs. The NNet quickly converged after ~40 iterations to a 100% accuracy rate of prediction achieved on the labeled data to within 10−8 relative tolerance.
The NNet outperformed alternative computational methods to classify spectra according to the principal components. For example, we evaluated the use of PLSR that identifies the dominant contribution of reference spectra to a new spectrum. The PLSR model built with 10 components only achieved 86% accuracy.
All the spectral data were then fed in the NNET model to be classified into different groups of minerals. We then render the classification data together at the corresponding peak positions into the reconstructed images, after the data were digitized into 32 bit and imported to imageJ software40.
Kerogen maturity analysis
We followed the approach of Ganz et al.5 who demonstrated that quantitative analysis of selected vibrational bands from FTIR data of bulk kerogen can provide a useful proxy for kerogen maturity, similar to a traditional van Krevelen diagram. Specifically, the A-factor was derived by finding the ratio of the peak area of C-H stretches (~2850, ~2920 cm−1) to the sum of this area and the peak area of the aromatic C=C bond (~1650 cm−1), and the C-factor was derived correspondingly by the ratio of the carbonyl (1710 cm−1) to the sum of the carbonyl and the aromatic C=C bond.
We calculated the Pearson’s correlation coefficients41 respectively between A- and C-factors, peak area of CO2 and the mineral classes identified by the NNet to find the significant co-locations described in the main text.
Speight, J. G. The chemistry and technology of petroleum (CRC Press, Taylor & francis Group, Boca Raton, 2014).
Charlet, L., Alt-Epping, P., Wersin, P. & Gilbert, B. Diffusive Transport and Reaction in Clay Rocks: A Storage (Nuclear Waste, CO2, H2), Energy (Shale Gas) and Water Quality Issue. Advances in Water Resources.
Craddock, P. R. et al. Evolution of Kerogen and Bitumen during Thermal Maturation via Semi-Open Pyrolysis Investigated by Infrared Spectroscopy. Energy & Fuels 29, 2197–2210 (2015).
Ballice, L., Yuksel, M., Saglam, M., Schulz, H. & Hanoglu, C. Application of Infrared-Spectroscopy to the Classification of Kerogen Types and the Thermogravimetrically Derived Pyrolysis Kinetics of Oil Shales. Fuel 74, 1618–1623 (1995).
Ganz, H. & Kalkreuth, W. Application of Infrared-Spectroscopy to the Classification of Kerogen-Types and the Evaluation of Source Rock and Oil-Shale Potentials. Fuel 66, 708–711 (1987).
Lis, G. P., Mastalerz, M., Schimmelmann, A., Lewan, M. D. & Stankiewicz, B. A. FTIR absorption indices for thermal maturity in comparison with vitrinite reflectance R-0 in type-II kerogens from Devonian black shales. Organic Geochemistry 36, 1533–1552 (2005).
Washburn, K. E., Birdwell, J. E., Foster, M. & Gutierrez, F. Detailed Description of Oil Shale Organic and Mineralogical Heterogeneity via Fourier Transform Infrared Microscopy. Energy & Fuels 29, 4264–4271 (2015).
Gasaway, C., Mastalerz, M., Krause, F., Clarkson, C. & Debuhr, C. Applicability of micro-FTIR in detecting shale heterogeneity. Journal of Microscopy 265, 60–72 (2017).
Lewis, L. L. & Sommer, A. J. Attenuated total internal reflection infrared mapping microspectroscopy of soft materials. Applied Spectroscopy 54, 324–330 (2000).
Patterson, B. M. & Havrilla, G. J. Attenuated total internal reflection infrared microspectroscopic imaging using a large-radius germanium internal reflection element and a linear array detector. Applied Spectroscopy 60, 1256–1266 (2006).
Patterson, B. M., Havrilla, G. J., Marcott, C. & Story, G. M. Infrared microspectroscopic imaging using a large radius germanium internal reflection element and a focal plane array detector. Applied Spectroscopy 61, 1147–1152 (2007).
Huth, F. et al. Nano-FTIR Absorption Spectroscopy of Molecular Fingerprints at 20 nm Spatial Resolution. Nano Letters 12, 3973–3978 (2012).
Muller, E. A., Pollard, B. & Raschke, M. B. Infrared Chemical Nano-Imaging: Accessing Structure, Coupling, and Dynamics on Molecular Length Scales. Journal of Physical Chemistry Letters 6, 1275–1284 (2015).
Bechtel, H. A., Muller, E. A., Olmon, R. L., Martin, M. C. & Raschke, M. B. Ultrabroadband infrared nanospectroscopic imaging. Proceedings of the National Academy of Sciences of the United States of America 111, 7191–7196 (2014).
Amenabar, I. et al. Hyperspectral infrared nanoimaging of organic samples based on Fourier transform infrared nanospectroscopy. Nature Communications 8 (2017).
Dominguez, G. et al. Nanoscale infrared spectroscopy as a non-destructive probe of extraterrestrial samples. Nature Communications 5 (2014).
Centrone, A. Infrared Imaging and Spectroscopy Beyond the Diffraction Limit. Annual Review of Analytical Chemistry 8(8), 101–126 (2015).
Wei, S. Y., Liu, F., Feng, X. H., Tan, W. F. & Koopal, L. K. Formation and Transformation of Iron Oxide-Kaolinite Associations in the Presence of Iron(II). Soil Science Society of America Journal 75, 45–55 (2011).
Muller, C. M. et al. Infrared Attenuated Total Reflection Spectroscopy of Quartz and Silica Micro- and Nanoparticulate Films. Journal of Physical Chemistry C 116, 37–43 (2012).
Kraft, S., Knittle, E. & Williams, Q. Carbonate Stability in the Earths Mantle - a Vibrational Spectroscopic Study of Aragonite and Dolomite at High-Pressures and Temperatures. Journal of Geophysical Research-Solid Earth 96, 17997–18009 (1991).
Parikh, S. J., Goyne, K. W., Margenot, A. J., Mukome, F. N. D. & Calderon, F. J. Soil Chemical Insights Provided through Vibrational Spectroscopy. Advances in Agronomy 126(126), 1–148 (2014).
Hillenbrand, R. & Keilmann, F. Optical oscillation modes of plasmon particles observed in direct space by phase-contrast near-field microscopy. Applied Physics B-Lasers and Optics 73, 239–243 (2001).
Aizpurua, J., Taubner, T., de Abajo, F. J., Brehm, M. & Hillenbrand, R. Substrate-enhanced infrared near-field spectroscopy. Optics Express 16, 1529–1545 (2008).
Soong, R. & Farmer, V. C. Infra-Red Spectra of Sulfides - M17 Identification of Sulfide Minerals by Infrared Spectrometry. Mineralogical Magazine 42, M17–M20 (1978).
Heath, C., Pejcic, B., Delle Piane, C. & Esteban, L. Development of far-infrared attenuated total reflectance spectroscopy for the mineralogical analysis of shales. Fuel 182, 771–779 (2016).
McLeod, A. S. et al. Model for quantitative tip-enhanced spectroscopy and the extraction of nanoscale-resolved optical constants. Physical Review B 90 (2014).
Hillenbrand, R., Taubner, T. & Keilmann, F. Phonon-enhanced light-matter interaction at the nanometre scale. Nature 418, 159–162 (2002).
Saif, T., Lin, Q. Y., Bijeljic, B. & Blunt, M. J. Microstructural imaging and characterization of oil shale before and after pyrolysis. Fuel 197, 562–574 (2017).
Chalmers, G. R., Bustin, R. M. & Power, I. M. Characterization of gas shale pore systems by porosimetry, pycnometry, surface area, and field emission scanning electron microscopy/transmission electron microscopy image analyses: Examples from the Barnett, Woodford, Haynesville, Marcellus, and Doig units. Aapg Bulletin 96, 1099–1119 (2012).
Bernard, S. et al. Multi-scale detection of organic and inorganic signatures provides insights into gas shale properties and evolution. Chemie Der Erde-Geochemistry 70, 119–133 (2010).
Michels, L. et al. Intercalation and Retention of Carbon Dioxide in a Smectite Clay promoted by Interlayer Cations. Scientific Reports 5 (2015).
Taifan, W., Boily, J. F. & Baltrusaitis, J. Surface chemistry of carbon dioxide revisited. Surface Science Reports 71, 595–671 (2016).
Schaef, H. T. et al. Surface Condensation of CO2 onto Kaolinite. Environmental Science & Technology Letters 1, 142–145 (2014).
Quiroz-Estrada, K. et al. N-2 and CO2 Adsorption by Soils with High Kaolinite Content from San Juan Amecac, Puebla, Mexico. Minerals 6 (2016).
LeCun, Y., Bengio, Y. & Hinton, G. Deep learning. Nature 521, 436–444 (2015).
R Development Core Team. (R Foundation for Statistical Computing, Vienna, Austria, 2014).
Beleites, C. S., Valter, Hyperspec: a package to handle hyperspectral data sets in R, R package version 0.98-20161118 (2016).
Mevik, B.-H. W., Ron; Hovde Liland, K., pls: Partial Least Squares and Principle Component Regression, R package version 2.6-0 (2016).
Venables, W. N., Ripley, B. D. & Venables, W. N. Modern applied statistics with S (Springer, New York, 2002).
Schindelin, J. R., C. T. & Hiner, M. C. (Molecular Reproduction and Development, 2015).
Dunn, K. W., Kamocka, M. M. & McDonald, J. H. A practical guide to evaluating colocalization in biological microscopy. American Journal of Physiology-Cell Physiology 300, C723–C742 (2011).
The authors thank Dr. Glenn Waychunas for providing us some of the mineral standards, Dr. Michael Martin for discussion on Ge-hemisphere applications, Dr. Hang Deng for comments on the impact of our work to the fracture evolution, Dr. Eoin Brodie for useful discussions on the machine learning models and support with his lab equipment, and Dr. Marco Voltolini for imaging and elemental detection with SEM/EDX. This work is supported by the Department of Energy, Laboratory Directed Research and Development funding, under contract DE-AC02-05CH11231. The development of the SINS instrument at the ALS was the result of a collaboration between beamline scientists at the ALS and Markus B. Raschke’s group at the University of Colorado, Boulder. The SINS measurement was performed at the Berkeley Synchrotron Infrared Structural Biology (BSISB) Program’s BL 5.4 at the Advanced Light Source. The BSISB program is supported by the US Department of Energy, Office of Science, and Office of Biological and Environmental Research and the Advanced Light Source is supported by the Director, Office of Science, and Office of Basic Energy Sciences under Contract DE-AC02-225 05CH11231.
The authors declare no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
About this article
Cite this article
Hao, Z., Bechtel, H.A., Kneafsey, T. et al. Cross-Scale Molecular Analysis of Chemical Heterogeneity in Shale Rocks. Sci Rep 8, 2552 (2018) doi:10.1038/s41598-018-20365-6
Spectro-Mechanical Characterizations of Kerogen Heterogeneity and Mechanical Properties of Source Rocks at 6 nm Spatial Resolution
Analytical Chemistry (2019)
Nanoparticles-mediated Brain Imaging and Disease Prognosis by Conventional as well as Modern Modal Imaging Techniques: a Comparison
Current Pharmaceutical Design (2019)
RSC Advances (2019)
Energy & Fuels (2018)
Science Bulletin (2018)