We introduce the application of microbial-induced calcite precipitation via the ureolytic soil bacterium Sporosarcina Pasteurii in freeze-dried form, as a means of enhancing overall MICP efficiency and reproducibility for geotechnical engineering applications. We show that the execution of urea hydrolysis and CaCO3 precipitation persist as a “cell-free” mechanism upon the complete breakdown of rehydrated cell clusters. Further, strength and stiffness parameters of bio-cemented sands are determined. Medium-grained bio-cemented sand yields compressive strengths up to 12 MPa while, surprisingly, fine-grained sand yields up to 2.5 MPa for similar bond contents. To understand the observed discrepancies, we undertake a systematic study of the bio-cemented material’s microstructure, by combining a series of microstructural inspection tools. The study extends beyond conventional qualitative and textural characterization and provides with new insight into the material’s peculiar 3D micro-architecture. We apply a new methodology towards quantifying crucial microscopic characteristics such as the particle sizes of the crystalline bond lattice, the bond-grain contacts and particle orientations. Bonds are found to exhibit distinctive geometries and morphologies when MICP applies to different base materials. We thus contribute to the debate on the importance of factors affecting: (i) MICP efficiency, (ii) the mechanical response and (iii) peculiar micro-architecture of bio-improved geo-materials.
The quest for novel, performant materials and solutions in engineering problems is driven nowadays by coupling technical innovation with economic efficiency and positive environmental impact. This quest is more current and pertinent than ever in the construction industry. Especially in urban areas “good” soils are already taken and the remaining land often requires extensive soil stabilization and strengthening works to secure the integrity of engineering projects and mitigate long-term risks related to failures and environmental threats.
This study puts the focus on bio-mediated soil cementation, an emerging technology which alters substantially the structure of geo-materials and endows the subsurface with improved overall mechanical behaviour. The technique integrates bacterial metabolic activity in soil-permeation solutions, to ultimately induce the formation of calcite (CaCO3) mineral crystals which act as binders among particles of granular soils. Quite unlike most applications targeting the artificial cementation of soils for improving their overall mechanical properties and bearing capacity1,2 microbial-induced calcite precipitation (MICP)3,4,5,6,7 via the ureolytic soil bacterium Sporosarcina Pasteurii8 is applied via non-erosive, low-pressure propagation of bio-chemical solutions. MICP at its core is urea hydrolysis with the catalyzing activity of the enzyme urease, which is found in several bacterial strains9 or other fungi and algae9,10. Due to the presence and activity of urease, urea hydrolysis completes 1014 times faster compared to the non-catalysed reaction11. The bio-improved geo-material can be, hence, produced in-situ at ambient temperature, with limited energy requirements from the relatively inexpensive combination of urea and calcium. The new, enhanced, lattice of mineral bonds among soil particles forms between several hours and few days, depending on the desired final bond content. It comprises calcite crystals which grow in number and size following hierarchical plane expansion with their dimensions ranging from few, up to hundreds of micrometers12. The resulting material is lightweight cemented soil which retains the permeability of its matrix4,13 exhibits significant enhancement of strength and stiffness14 and is difficult to produce by any other synthetic means.
There is still uncertainty, however, about the design and application of a controlled, large-scale soil improvement mechanism based on MICP, despite the extensive knowledge established via laboratory experimentation15,16,17,18,19,20,21. Few attempts have been made at large scale targeting real geo-technical problems22,23,24 and in some cases failed to reproduce the desired precipitation mechanism25. A crucial takeaway from such attempts is the improved understanding of the effect of the provided bio-chemical treatment conditions on the material’s improved mechanical response. However, the role of the intrinsic properties of the base material on the formation of the bond lattice remains relatively underexplored.
To this purpose, in the present study we adopt two different base materials and subject them to identical external treatment conditions to ultimately evaluate whether and how complex bio-chemical and transport phenomena adapt to the different available porosities. Additionally, we focus on the study of kinetics of urea hydrolysis for the case of MICP induced via utilizing lyophilized cells. The use of this cell state, which is an alternative to the direct use of vegetative cells, is considered to facilitate significantly MICP applications by overcoming the need for complex on-site bacteria cultivation26. It further incorporates elements of economic efficiency by lowering energy requirements and needs in resources and equipment for in-situ applications. Moreover, it ensures that quality control tests are carried out prior to propagating solutions in the targeted soil volume. Overall, MICP is rendered easier to reproduce, since the most crucial elements of the process, i.e. the bacterial agents, can be stored, transported and become ready to use.
Finally, although the bio-cemented geo-material was brought into focus over a decade ago4,9 its peculiar structure, result of bio-chemical and transport processes, has been treated solely in qualitative approaches, via surface and textural observations. In the context of the current knowledge27,28,29 microstructural information has been captured and outlined mainly through scanning electron microscopy (SEM). More precisely, the chemical composition of treatment solutions27, the environmental conditions28 and the degree of saturation29 during MICP improvement are all found to yield distinctive precipitation behaviors and correspond to varying obtained mechanical properties. Moreover, microstructural evidence provided in the literature is often limited to the scale of few grains and bonds and thus it remains unclear whether such evidence can be considered representative of the macro-scale.
To overcome such uncertainties regarding the limited validity of textural observations, micro-computed tomography (micro-CT) is considered herein as the ultimate tool which allows providing with a robust determination of micro-scale quantities. The goal is to capture spatial and morphological heterogeneities of micro-scale properties. Recent work in this direction has been reported in30 where micro-CT is mobilized for capturing microstructural quantities and their evolution with respect to changes in rheological properties, such as the porosity, permeability and effective diffusion. In the same work, comparison between the experimentally measured bond volumetric fraction and that obtained through micro-CT image processing is reported, with the mean error between the two reaching 20%. Contrary to30, the work presented herein deals with the micro-architecture of bio-cemented materials by implementing micro-CT to isolate and analyze individual bond particles which compose the calcite lattice in two different base materials. Results on the geometrical and spatial characteristics are interpreted and evaluated with respect to the captured strength and stiffness parameters. Moreover, complementary microstructural inspection tools are mobilized to further shed light on the bond growth mechanism and on the previously underexplored internal state of calcite bonds.
Kinetics of cell-free MICP
Previous studies reported in the literature5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24 have utilized extensively whole vegetative cells of Sporosarcina Pasteurii which are introduced in soils to ultimately induce their bio-cementation. Herein, we obtain ureolytic cells in dry powder form through a freeze-drying process and evaluate their ureolytic capacity upon rehydration, as described in the methods section. When re-suspended in urea- and calcium-rich solutions, the lyophilized cells of S. Pasteurii are found to reactivate their hydrolysis mechanism and CaCO3 precipitates are immediately formed.
Electrical conductivity serves herein as an indicator of the produced ammonium concentration, and thus of the amount of urea hydrolysed according to9. A maximum urea hydrolysis rate of 104 mmol/L−1/h−1 is obtained (Fig. 1a), which is within the same range as that reported in31 and as that found for similar biomass concentrations in9. These two latter studies refer to the use of vegetative cells harvested from liquid growth media and directly introduced into soils. The study of Fig. 1a reveals a continuous increase of the electrical conductivity despite complete cell lysis, which is found to occur in the first 5 hours following cell resuspension. Figure 1b reveals cubic-shaped CaCO3 crystals exhibiting hierarchical precipitation patterns, with traces of encapsulated cells being captured in Fig. 1c. Similar hierarchical expansion of bond particles which reproduce distinctive plane geometries has been also reported by the authors in12. Lysis is monitored through optical density measurements (Fig. 1a) and photomicroscopy analyses (Fig. 1d). A hypothesis based on the provided evidence is that while bacteria decay, their urease enzymes are released in the surrounding environment, carrying and executing the genetic sequences of urea hydrolysis. This “cell-free” mechanism of urea hydrolysis, captured herein, can potentially replace in vivo hydrolysis and facilitate real-field MICP applications by reducing installation costs and by overcoming the need of biosafety approvals according to26. This alternative use of freeze-dried cells is therefore expected to set the basis for the design of overall reproducible, “mainstream” soil-improvement solutions based on bio-mediated CaCO3 precipitation.
Mechanics of the bio-improved geo-materials
We provide with results referring to the unconfined compressive strength (UCS) of fine- and medium-grained sand, with their identification properties listed in Table 1. It should be noted that the cumulative 50% point diameter (D50) of the former is almost half of that of the latter. Both materials are subjected to MICP to achieve various calcite bond contents in the range between 3–10%, by altering the number of the provided reactant batches which are rich in urea and calcium. Further details on specimen preparation are available in12. Same external treatment conditions are provided to sand columns where the materials are packed as a means of minimizing uncertainties related to the influence of bio-chemical and environmental conditions on the precipitated bond lattice. Thus, the morphology of the crystalline assembly of bonds, result of MICP, will be attributed only to the influence of the base materials’ initial porosity.
Interestingly, our data reveal a more pronounced strength (Fig. 2a) and stiffness (Fig. 2b) improvement for the more porous material. It should be noted that both materials yield the same peak and residual strengths in the untreated state32 under confinement. The UCS of medium-grained bio-improved sand falls between 3 and 12 MPa for calcite bond contents in the range of 5% to 10%. Meanwhile, the fine bio-improved sand reaches approximately 2.5 MPa for similar bond contents (Fig. 2a). The variation of the bio-improved Young’s moduli are found to exhibit similar trends with respect to increasing calcium carbonate content for both materials. For comparison, the elastic modulus of the untreated materials during unloading-reloading is estimated in the range of 200 MPa32. Medium-grained bio-cemented sand is found to yield higher stiffness values for all samples with their bond content greater than 5% (Fig. 2b).
The discrepancy observed in the achieved strength of bio-improved materials, which yielded similar response in their untreated state, suggests that in order to provide with a robust description of the enhanced behavior, the overall bulk mass of bonds cannot be considered as the sole factor governing the level of improvement. A better understanding of microstructural properties is hence required.
Qualitative and quantitative microstructural characterization
The present section comprises a description of the distinctive CaCO3 precipitate behaviours through 3D microstructural characterization. Figure 3 shows the process of volume reconstruction through combination of 2D X-Ray scans, where sand particles (brown) and calcite bonds (green) can be distinguished and analyzed individually. As a starting point we postulate that higher initial porosity (medium-grained sand) favors precipitation of bond particles which grow their sizes upon continuous infiltration of reactive media throughout the porous network. Furthermore, the nature of the precipitation and bond growth mechanisms is analyzed via mobilizing complementary inspection tools. Observations through qualitative inspection aim, on one hand, to serve as additional means of validation of the parameters determined via micro-CT33 and subsequent analysis34 of the reconstructed 3D solid matrix. On the other hand, alternative tools allow, for example, observing in real-time the precipitation and bond growth mechanisms, as well as better understanding the internal state of crystals.
To address the quantification of microscale parameters with respect to the calcite bond content herein is presented a methodology towards capturing the contacts between bonds and grains, as well as expressing the numbers, sizes, and particle orientations. A workflow is established and presented in the methods section referring to analyses through micro-CT. This workflow allows investigating the representary elementary volume (REV) scale to identify microstructural characteristics which are considered representative of the material’s macroscale. To this purpose, the analyzed volumes via micro-CT refer to dimensions at least ten-times the D50 values of the investigated materials (Table 1).
The core of this digital image based approach consists in passing from a raw image obtained via micro-CT (Fig. 4e) to a segmented one (Fig. 4f) where the different solid phases, as well as the pore space, are identified. Subsequently, soil grains need to be separated since they often appear interconnected in the raw images, which hinders the accurate determination of their numbers and volumes. This separation method with distance transformation34 allows splitting individual soil particles. Further, by observing the intersection of bond particles with the produced split lines which divide sand particles, it becomes possible to identify the number of active bonds and the active area of contact (Fig. 4f). More precisely, bond particles which intersect with the imaginary lines splitting individual soil grains are considered as active, contributing with their planes to the transmission of normal forces and to the development of shear resistance. Active contact areas, which represent the intersection of bonds with the split lines in the three-dimensional space, are illustrated, under the same scale, in Fig. 5 for fine- and medium- grained bio-cemented sand.
We further suggest a bond particle analysis which expresses the particle size distribution with respect to the cumulative bond volume. This analysis follows the principle of the well-established experimental procedure for determining the grain size distribution of soils35. More precisely, the minimum and maximum bond diameters are used as indicators of the size range exhibited by the precipitated bond particles with respect to the cumulative fraction of the bond volume (Fig. 2e,f). In Fig. 2e and f the mean minimum (D50 min) and mean maximum (D50 max) diameters are determined as the cumulative 50% points of diameter. These values are plotted for both materials in Fig. 4d. In addition to these parameters, we define the average contact diameter (Fig. 4d) per bond as the ratio of the overall contact area between bonds and sand grains over the total number of active bonds. The average contact diameter per bond is thus a direct function of the total number of particles, contrary to the aforementioned D50 diameters which incorporate the notion of the cumulative volume of the bond phase. It is noteworthy to consider herein that active bonds are those which are found to bridge neighbouring soil particles. The remaining bonds are characterized as inactive since they do not contribute with their planes to inter-granular force transmission. A typical example of a real geometry and texture of active and inactive bonds is captured through scanning electron microscopy (SEM) and illustrated in Fig. 6.
The mean minimum and maximum diameters of bonds precipitated in medium-grained sand are found to range between 80–370 micrometres for calcite volumetric contents in the range between 3–7.5% (Figs 2f and 4d). Contrary, MICP treatment in fine-grained sand yields bonds with mean diameters in the range between 100–200 micrometres for calcite contents between 9–13% (Figs 2e and 4d). We postulate that larger bond particle diameters result in lower values of inter-particle stresses, in larger plane surfaces for the development of forces resisting shearing and in increased particle interlocking. This explains why increased overall resistance is captured for the medium-grained bio-cemented sand for similar bond contents with respect to fine-grained sand.
The particle orientation theta of the major inertia axis of individual bond particles is used to determine the spatial orientations of population of bonds (Fig. 2c and d). For MICP-treated medium-grained sand (Fig. 2d), bonds are found to exhibit a relatively homogenous distribution in the theta-orientation space compared to calcite bonds that precipitate in fine-grained sand (Fig. 2c). In this latter case, populations of grains yield preferential orientations around approximately 45° and 235°. We postulate that the homogeneity in the spatial distribution of crystals, and therefore of intergranular contacts along all directions, results in increased overall resistance. However, lack of particles which resist transmitting forces in a given directional range, results to weaker force chain distributions, a term commonly confronted in discrete element method (DEM) simulations36 and thus to lower overall shear resistance.
Results further reveal that the fraction of active bonds is estimated between 77–84% for the 6 samples analyzed through micro-CT and reconstructed numerically. The bonds per soil particle ratios are found to range between 4.3 and 3.2 for fine- and medium-grained sand respectively, independently of the overall calcite content.
We further provide a qualitative description of precipitation behaviours to understand the evolution of bond geometries with respect to the crucial overall bond content. To this purpose we perform observations via time-lapse video microscopy to obtain real-time monitoring of the evolution of MICP within a Polydimethylsiloxane (PDMS)37,38 physical model of a microporous medium. Observations reveal the immediate precipitation of CaCO3 nuclei upon the introduction of reactants and their gradual deposition on the PDMS grains’ surfaces (Fig. 4a,b). This finding suggests a growth mechanism for precipitated CaCO3 nuclei owing to the gradual accumulation of individual CaCO3 layers in areas of the porous medium that are less exposed to advective fluxes. An additional inspection tool employed herein relates to the investigation of a cross sectional area of a calcite bond through the back-scattered electron detector of a SEM microscope. The sample is previously subjected to ion-beam bombardment to ultimately obtain a planar, smoothened surface. Observation of the inner structure of calcite bonds reveals distinctive individual layers which compose a single crystalline bond (Fig. 4c). These observations validate, on one hand, the hypothesis of gradual deposition of precipitated nuclei which results to bond growth, previously observed via time-lapse video microscopy (Fig. 4a,b). On the other hand, the observed layers, as well as the traces of encapsulated bacterial cells within the CaCO3 bond, represent crystalline defects. The presence of defects and dislocations suggest that the engineering properties of calcite bonds in bio-improves soils, result of bio-mediated precipitation, are lower than those of pure geological calcite.
As far as the validity of the obtained results from micro-CT and image processing is concerned, we compare the geometrical characteristics determined via micro-CT and subsequent 3D volume reconstruction with parameters measured directly in the laboratory under standardized experimental procedures. More precisely we generate the 3D packing of sand particles and analyze their grain size distribution. Results, shown in solid red lines in Fig. 2e and f, are then compared against the experimentally measured curves of the particle size distribution34, shown in dashed red lines in Fig. 2e and f, with good agreement found between the two. Moreover, since micro-CT is a non-destructive inspection technique, the samples can be further subjected to post-scanning analyses, such as acid digestion12, for ultimately determining directly the crucial calcite bond content. When comparing the indirect, numerical measurements of the bond contents with direct measurements performed in the laboratory on the same samples, results reveal an error range between 2.2% and 15.1% in the total calcite content. Finally, this error between direct and indirect measurements of the calcite content confirms similar range as that reported in30, found to reach 20%. Such discrepancies are expected given the limitations in the maximum resolution achieved by the micro-CT equipment.
The study condenses a multi-disciplinary approach to the investigation of bio-cemented geo-materials. More precisely notions of: (i) kinetics of precipitation, (ii) mechanics and (iii) microstructural inspection are brought together to provide with new insight into the contributing mechanisms and efficiency of the MICP process. The contributions of this study are summarized below based on these three principal axes.
Firstly, an alternative application of MICP for soils was introduced and discussed. Kinetics analyses showed that urea hydrolysis and calcium carbonate precipitation persist in a “cell-free” mechanism, after complete breakdown of the cell clusters of rehydrated calcifying bacteria. Additionally, the efficiency of the urease enzyme is not found to vary after application of freezing-drying and rehydration cycles or after the degradation of the cell cluster. This fundamental evidence provides with a preliminary step towards the conception of an efficient and reproducible mechanism for soil improvement based on MICP where given dry biomass yields known ranges of hydrolysis and precipitation efficiencies.
Moreover, strength and stiffness parameters are obtained for fine- and medium-grained bio-cemented samples of various overall bond contents. By applying two base materials, which yield similar response in their untreated state, to identical external treatment conditions we minimize uncertainties related to the influence of bio-chemical factors on the obtained mechanical response. Results reveal a more pronounced improvement for the medium-grained material, for similar range of the final calcite bond content. This finding confirms that the average bulk mass of bonds is not sufficient to determine the level of improvement and thus the contribution of the crystalline skeleton of bonds needs to be better understood.
In light of the captured mechanical response the study extended to cover the investigation of the three-dimensional micro-architecture of bio-cemented geo-materials. A new approach was presented which allows estimating the crucial contact area between bonds and sand grains through micro-CT analyses and subsequent 3D volume reconstruction. Microscopic parameters, such as bond sizes, numbers and orientations are determined in the representary elementary volume scale. This allows considering that the quantified parameters reflect the fabric of the material at the macroscale. Distinctive trends were obtained for the geometrical and spatial distributions of microbial-induced calcite precipitates, forming the crystalline lattice of bonds within fine- and medium-grained soils. These distinctive morphological characteristics were discussed in relation to the mechanical behaviour of the material at the macroscale.
Moreover, microscale inspection goes beyond traditional textural observations and provides with new, real-time insight into the nature of the growth mechanism and into the internal state of crystalline bonds. Deposition of precipitated nuclei was identified as a principal bond growth mechanism.
Overall, the study contributes towards an advanced characterization of the peculiar bio-cemented geo-material. A passing from qualitative approaches towards the quantification of critical parameters of its micro-architecture was presented. The improved understanding provided herein forms a new basis for the conception of modelling formulations which incorporate notions of contact mechanics or other parameters to unify microscopic quantities as a means of interpreting macroscale phenomena. Thus, the provided insight can be used to improve predictive theoretical modelling and numerical simulations. For example, a practical application of the provided insight into the peculiar architecture of the bio-improved geo-material would be to design and perform simulations using DEM36,39,40,41 on 3D particle packings where bonds represent realistic geometries and microstructural characteristics of the material. Finally, the introduced workflow to investigate, reproduce and analyse the fabric of the material can be adopted and extended to similar, natural or composite, materials with distinctive fabric properties.
Sporosarcina Pasteurii8, which was obtained from the ATCC bacteria culture collection, is grown under sterile conditions in a liquid broth medium with its composition listed in ATCC Medium 1376. Images are collected via photomicroscopy (Nikon NI-U Microscope) at several intervals during the growth phase to evaluate the cell state and associate it with the optical density that was measured at 600 nm and ensure that no contamination occurs. An optical density equal to 1 yields 108 colony-forming units (cfu) per millilitre (ml), which is determined via plating an aliquot of the liquid culture on an agar plate (with its composition mentioned in ATCC Medium 1376) using the spread plate technique.
Subsequently, the cells are centrifuged at 4 °C at 4000 g for 20 minutes. The supernatant is removed and the pellet is resuspended in liquid yeast extract medium and stored at 4 °C. Alternatively, the pellet is resuspended in the lyophilisation solution, which includes Milli-Q water, 10% NH4Cl and 10% sucrose. NH4Cl is provided at the same concentration as in the culture broth to alter the osmotic neutrality of Milli-Q water and to avoid cell lysis upon resuspension of the pellet. Sucrose is provided to maintain the integrity of the bacterial cells upon dehydration during the freeze-drying process. Upon resuspension in the lyophilisation solution, cells are stored at −80 °C for 1 hour. Subsequently, the frozen stock is placed in a vacuum chamber (Christ LCG Lyo Chamber Guard) at a minimum pressure of 0.014 bars for 24 hours. The obtained freeze-dried cultures in powder form are subsequently maintained in closed vials to protect them from atmospheric humidity and stored upon rehydration for application of MICP.
Batch experiments are carried out for measuring the electrical conductivity which corresponds to the production of ammonium and can thus be associated with the mass of urea hydrolysed. The hydrolysis of 1 mole of urea corresponds to the release of two moles of ammonium (NH4+), which results in increased electrical conductivity and alkalinity of the solution. The relationship between the total urea hydrolysed and total increase in electrical conductivity of the solution is given in9:
As far as the microstructural analyses are concerned, we introduce a bond analysis presented in Figs 2 and 3 which uses the cumulative bond volumetric fraction as a weighting parameter. We thus follow the similar principle with the traditional determination of the grain size distribution, where the particle minimum diameters are expressed with respect to the cumulative mass fraction of population of grains35.
Scans were performed with the X-ray μ-CT SkyScan 1173 high energy micro-tomography scanner (Bruker MicroCT) which is equipped with a Hamamatsu 130/300X-ray beam source and a camera detector which yields images of resolutions equal to 2,240 × 2,240 pixels. Samples that are subjected to micro-CT have diameters up to 5 mm and heights up to 15 mm (micro-columns). The voxel size of the obtained images is 6.41 μm and 7.12 μm for samples of fine- and medium-grained MICP-treated sands, respectively.
A step adopted during the image processing approach shown in Figs 3, 4 and 5 lies in separating individual sand grains. As observed in Fig. 3e and f, individual contact points between soil grains are not detected via micro-CT scans due to the limitations in resolution provided by the equipment. Sand grains in the obtained raw images are connected with several pixels, hindering the estimation of their number, volume and diameters. We therefore implement a particle separation technique based on the principle of watershed lines coupled with distance transformation34 for ultimately obtaining the lines that split individual sand particles. An advantage of the particle separation operation performed herein is that there is no deletion of pixels, thus the particle volume remains unchanged. Upon particle separation, we perform a logical operation on the obtained binary images referring to the lines separating sand grains (namely A) and that of the segmented bond phase (namely B). For every pixel x which belongs to images A and B we obtain a new image C upon the logical operation described as follows:
Image C, resulted from the superposition of A and B, allows determining in quantitative terms the total active contact area by analyzing the length of the split lines intersecting with bond particles in the two-dimensional space and the total area in the three-dimensional space (Fig. 5). Bonds that do not cross the split lines are considered as inactive.
The datasets generated and analysed during the current study related to the microstructural characterization of the materials will become available on Re3data prior to publication date. Data series obtained and analysed for the kinetics and mechanics studies are available from the corresponding author on reasonable request.
Mihalis, I. K., Tsiambaos, G. & Anagnostopoulos, A. Jet grouting applications in soft rocks: the Athens Metro case. Geotechnical Eng. 157, 219–228 (2004).
Vilarrasa, V., Carrera, J., Jurado, A., Pujades, E. & Vázquez-Suné, E. A methodology for characterizing the hydraulic effectiveness of an annular low-permeability barrier. Eng Geo. 120(1), 68–80 (2011).
Whiffin, V., van Paassen, L. & Harkes, M. Microbial carbonate precipitation as a soil improvement technique. Geomicrobiol J. 24(5), 417–423 (2007).
Mitchell, J. K. & Santamarina, J. C. Biological considerations in geotechnical engineering. J Geotech Geoenviron. 131(10), 1222–1233 (2005).
DeJong, J. T. et al. Biogeochemical processes and geotechnical applications: progress, opportunities and challenges. Geotechnique. 63(4), 287 (2013).
Umar, M., Kassim, K. A. & Chiet, K. T. P. Biological process of soil improvement in civil engineering: A review. J Rock Mech Geo Eng. 8(5), 767–774 (2016).
Mujah, D., Shahin, M. A. & Cheng, L. State-of-the-Art Review of Biocementation by Microbially Induced Calcite Precipitation (MICP) for Soil Stabilization. Geomicrobiol J. 34(6), 524–537 (2017).
Yoon, J. H. et al. Sporosarcina aquimarina sp. nov., a bacterium isolated from seawater in Korea, and transfer of Bacillus globisporus (Larkin and Stokes 1967), Bacillus psychrophilus (Nakamura 1984) and Bacillus pasteurii (Chester 1898) to the genus Sporosarcina as Sporosarcina globispora comb. nov., Sporosarcina psychrophila comb. nov. and Sporosarcina pasteurii comb. nov., and emended description of th. Int J Syst Evol Micr. 51(3), 1079–1086 (2001).
Whiffin, V. Microbial CaCO3 precipitation for the production of biocement (PhD dissertation, School of Biological Sciences and Biotechnology, Murdoch University, Perth, Australia, 2004).
Hamdan, N. & Kavazanjian, E. Enzyme-induced carbonate mineral precipitation for fugitive dust control. Geotechnique. 66(7), 546–555 (2016).
Hausinger, R. P. Biochemistry of nickel Vol. 12 (Springer Science & Business Media, 2013).
Terzis, D., Bernier-Latmani, R. & Laloui, L. Fabric characteristics and mechanical response of bio-improved sand to various treatment conditions. Géotech Lett. 6(1), 50–57 (2016).
Zamani, A. & Montoya, B. M. Permeability Reduction Due to Microbial Induced Calcite Precipitation in Sand. Paper presented at Geo-Chicago 2016: Sustainable Environmental Systems, Chicago, Illinois. Place of publication: Geotechnical Special Publication 271, Geo-Institute (August, 14–18) 2016.
Harkes, M. P. et al. Microbial induced carbonate precipitation as ground improvement method–bacterial fixation and empirical correlation CaCO3 vs strength. Paper presented at the 1st International Conference on Bio-Geo-Civil Engineering, Delft, The Netherlands (2008).
Harkes, M. P., Van Paassen, L. A., Booster, J. L., Whiffin, V. S. & van Loosdrecht, M. C. Fixation and distribution of bacterial activity in sand to induce carbonate precipitation for ground reinforcement. Ecol Eng. 36(2), 112–117 (2010).
Van Paassen, L. A. Biogrout, ground improvement by microbial induced carbonate precipitation (PhD dissertation, TU Delft, Delft University of Technology, 2009).
DeJong, J. T. et al. Bio-mediated soil improvement. Ecol Eng. 36(2), 197–210 (2010).
Venuleo, S., Laloui, L., Terzis, D., Hueckel, T. & Hassan, M. Microbially induced calcite precipitation effect on soil thermal conductivity. Geotech Lett. 6(1) (2016).
Al Qabany, A. & Soga, K. Effect of chemical treatment used in MICP on engineering properties of cemented soils. Géotechnique. 63(4), 331–339 (2013).
Carmona, J. P., Oliveira, P. J. & Lemos, L. J. Biostabilization of a Sandy Soil Using Enzymatic Calcium Carbonate Precipitation. Procedia Engineer. 143, 1301–1308 (2016).
Cheng, L. Innovative ground enhancement by improved microbially induced CaCO3 precipitation technology (PhD dissertation, Murdoch University, 2012).
Filet, A. E., Gadret, J. P., Loygue, M. & Borel, S. Biocalcis and its applications for the consolidation of sands. Grouting and deep mixing. 1767–1780 (2012).
Gomez, M. G. et al. Field-scale bio-cementation tests to improve sands. P I Civil Eng-Ground Improvement. 168(3), 206–216 (2015).
Van Paassen, L. A. et al. Scale up of BioGrout: a biological ground reinforcement method. Paper presented at the 17th international conference on soil mechanics and geotechnical engineering, Alexandria, Egypt. Lansdale IOS Press. 2328–2333 (2009).
Van Paassen, L. A. Bio-mediated ground improvement: from laboratory experiment to pilot applications. Paper presented at the Geo-Frontiers 2011: Advances in Geotechnical Engineering, Dallas, Texas (March, 13–16) 2011.
Volodymyr, I. & Chu, J. Applications of microorganisms to geotechnical engineering for bioclogging and biocementation of soil in situ. Reviews in Environmental Science and Bio/Technology. 7(2), 139–153 (2008).
Al Qabany, A., Kenichi, S. & Santamarina, C. Factors affecting efficiency of microbially induced calcite precipitation. J Geotech Geoenviron. 138(8), 992–1001 (2011).
Mortensen, B. M., Haber, M. J., DeJong, J. T., Caslake, L. F. & Nelson, D. C. Effects of environmental factors on microbial induced calcium carbonate precipitation. J Appl Microbiol. 111(2), 338–349 (2011).
Cheng, L., Cord-Ruwisch, R. & Shahin, M. A. Cementation of sand soil by microbially induced calcite precipitation at various degrees of saturation. Can Geotech J. 50(1), 81–90 (2013).
Dadda, A. et al. Characterization of microstructural and physical properties changes in biocemented sand using 3D X-ray microtomography. Acta Geotech 12(5), 955–970 (2017).
Lauchnor, E. G. et al. Whole cell kinetics of ureolysis by Sporosarcina pasteurii. J Appl Microbiol. 118(6), 1321–1332 (2015).
Terzis, D. & Laloui, L. On the Application of Microbially Induced Calcite Precipitation forSoils: A Multiscale Study (eds Ferrari, A. & Laloui, L. Springer Series in Geomechanics and Geoengineering, Springer, Cham 2017).
Ketcham, R. A. & Carlson, W. D. Acquisition, optimization and interpretation of X-ray computed tomographic imagery: applications to the geosciences. Comput Geosci. 27(4), 381–400 (2001).
Avizo user’s guide. FEI company – Thermoscientific (2009).
ASTM D6913/D6913M-17. Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis. ASTM International, West Conshohocken PA. (2017).
Wang, Y. H. & Leung, S. C. A particulate-scale investigation of cemented sand behavior. Can Geotech J. 45(1), 29–44 (2008).
Yang, W. et al. Fabrication of a Hydrophilic Poly (dimethylsiloxane) Microporous Structure and Its Application to Portable Microfluidic Pump. Jpn J Appl Phys. 49(6S), 06GM01 (2010).
Jiménez-Martínez, J. et al. Pore-scale mechanisms for the enhancement of mixing in unsaturated porous media and implications for chemical reactions. Geophys Res Lett. 42(13), 5316–5324 (2015).
Evans, T. M., Khoubani, A. & Montoya, B. M. Simulating mechanical response in bio cemented sands. Paper presented at the 14th international conference of the international association for computer methods and recent advances in geomechanics: IACMAG 2014, Kyoto, Japan (Taylor and Francis, Balkema, 2015).
Feng, K., Montoya, B. M. & Evans, T. M. Discrete element method simulations of bio-cemented sands. Comput Geotech. 85, 139–150 (2017).
Yang, P., O’Donnell, S., Hamdan, N., Kavazanjian, E. & Neithalath, N. 3D DEM Simulations of Drained Triaxial Compression of Sand Strengthened Using Microbially Induced Carbonate Precipitation. Int J Geomech. 17(6), 04016143 (2017).
The authors would like to acknowledge the support of the Lombardi Foundation (Switzerland). The authors would like to further acknowledge the support of Prof. Pietro de Anna from the Geosciences Faculty of the University of Lausanne (UNIL) for his contribution in conducting the time-lapse video microscopy analysis. Additionally, the authors express their sincere thanks to the Swiss National Science Foundation (SNSF) (grant 200021_140246) and Swiss Federal Commission for Scholarships for Foreign Students (Swiss Government Excellence Scholarship ESKAS-Nr: 2014·0276) for their financial support.
The authors declare that they have no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
About this article
Cite this article
Terzis, D., Laloui, L. 3-D micro-architecture and mechanical response of soil cemented via microbial-induced calcite precipitation. Sci Rep 8, 1416 (2018). https://doi.org/10.1038/s41598-018-19895-w
Journal of Transportation Engineering, Part B: Pavements (2020)
Assessing the Kinetics and Pore‐Scale Characteristics of Biological Calcium Carbonate Precipitation in Porous Media using a Microfluidic Chip Experiment
Water Resources Research (2020)
Applied Clay Science (2020)
Investigation of pore-scale CaCO3 distributions and their effects on stiffness and permeability of sands treated by microbially induced carbonate precipitation (MICP)
Soils and Foundations (2020)
Mathematical modelling and simulation of microbial carbonate precipitation: the urea hydrolysis reaction
Acta Geotechnica (2020)