Abstract
Recently, there have been significant efforts to guide mechanical energy in structures by relying on a novel topological framework popularized by the discovery of topological insulators. Here, we propose a topological metamaterial system based on the design of the Stewart Platform, which can not only guide mechanical waves robustly in a desired path, but also can be tuned in situ to change this wave path at will. Without resorting to any active materials, the current system harnesses bistablilty in its unit cells, such that tuning can be performed simply by a dial-in action. Consequently, a topological transition mechanism inspired by the quantum valley Hall effect can be achieved. We show the possibility of tuning in a variety of topological and traditional waveguides in the same system, and numerically investigate key qualitative and quantitative differences between them. We observe that even though both types of waveguides can lead to significant wave transmission for a certain frequency range, topological waveguides are distinctive as they support robust, back scattering immune, one-way wave propagation.
Similar content being viewed by others
Introduction
The discovery of topological insulators1,2, which are labelled as a new state of matter in the condensed matter physics, has galvanized research efforts in multiple fields. Topological framework enables us to understand fascinating phenomena such as quantum Hall effect (QHE)3,4, quantum spin Hall effect (QSHE)5, and quantum valley Hall effect (QVHE)6. These are special because of the intriguing directional and robust edge states they support. It is recent that these fundamental concepts have been extended to the fields of photonics7, acoustics8,9,10,11,12,13,14, and mechanics15,16,17,18,19,20,21,22,23,24,25,26. Such extension is of the fundamental interest to the research community as it has potential to set new design principles for topological metamaterials that aim to strategically tailor energy transport for waveguiding, isolating, switching, filtering, and related applications.
Acoustic and mechanical metamaterials that rely on QHE need active components (e.g., gyroscope and flow circulator) or applications of external fields (e.g., magnetic field) to break the time reversal symmetry8,9,10,16,17,18,19. This adds complexity to the system, and thus, these metamaterials based on QHE are challenging to be realized in practical environments. QSHE-inspired metamaterials employ only passive components, but usually mandate intricate ways to achieve a double Dirac cone in their dispersion relation11,12,20,21,22,23. Metamaterials based on QVHE13,14,24,25,26, however, rely on the breakage of the inversion symmetry to achieve topological properties, and these can be comparably easier to be designed and realized in practical settings. QVHE originates from the newly discovered valley degree of freedom (DOF) of electrons in the two-dimensional honeycomb lattice of graphene6. These valley DOFs are energetically degenerate but are largely separated in momentum space13,14. Due to this large separation, inter-valley scattering can be avoided, and valley DOFs constitute two pseudo-spins, which have opposite-directional and robust properties on the topological interfaces. On this principle, back-scattering immune and robust energy transport along topological waveguides with sharp bends have been proposed in acoustic13,14 and mechanical25,26 systems.
Though the aforementioned configurations have shown to be guiding energy in a specific path in the system, there remains a challenge; Can one change the path in situ and thus achieve a complete control over the waveguide? Once achieved, this will provide a fertile testbed for future experiments related to wave guiding capability of various types of topological interfaces, and at the same time those can be compared with traditional waveguides in the same system more closely than ever. However, adding such versatility into the system comes at a cost. Generally, in situ tunability requires complex components or mechanisms to be present in the system, so that the wave path in the lattice structure can be reconfigured in a controllable and versatile manner. But such complexity in design could again make the system cumbersome for practical use, and it would defeat the purpose of building a simple QVHE-based system to some extent.
Here we show that in situ tunability in the QVHE-based mechanical metamaterial can be achieved by utilizing nonlinearity of the constituent elements in the system. More specifically, we use an assembly of the Stewart Platform (SP), in which translation and rotational degrees of freedoms of each SP are judiciously tailored to achieve a bistable response. Consequently, a simple dial-in action changes its configuration from one stable state to the other, and this feature can be used for in situ control of the wave path in the system. The SP already has a wide range of engineering applications such as vibration control, precise positioning, and flight simulation27,28. Therefore, by integrating the elegant engineering of SP with the fascinating physics of QVHE, we propose a dial-in mechanical metamaterial for creating tunable topological waveguides. We use extensive numerical simulations and show that this metamaterial can be tuned in situ to design a variety of topological waveguides with robust wave propagation characteristics. The tunability allows us to also build traditional waveguides by suppressing topological variations in the same systems, making it possible to compare their performance with the topological counterpart to a remarkable detail. Such a comparison therefore plays a key role in extending our knowledge and appreciation towards the uniqueness of topological waveguides in the proposed system.
Results
Design of the tunable topological metamaterial
The tunable system we propose is illustrated in Fig. 1. Each SP is bistable, i.e., it has two stable configurations: Y-state (yellow) and P-state (purple) as shown in Fig. 1a,b. This unit is made of two parallel disks connected with six linear springs. The conventional SP unit has six DOFs for the top disk, while the bottom disk is fixed27. However, by judiciously choosing the connecting springs, one can decouple some DOFs and reduce the total DOFs (see Supplementary Note 1). In this study, for the sake of simplicity, we assume that the bottom disk in pinned at its center, such that it can only rotate about the z-direction. We denote this rotational DOF of the bottom disk by ϕb. The top disk can have only rotational (ϕt) and translational (wt) motions along the z-direction with respect to its equilibrium position. Note that these dynamic perturbation parameters, ϕb, ϕt, and wt, should not be confused with θ0 and h0, which denote the equilibrium parameters of the SP unit cell and vary depending on whether it is in the Y- or P-state (Fig. 1a). All three DOFs of these dynamic motions in terms of ϕb, ϕt, and wt are governed by the six springs between the plates. The detailed mathematical relationships – including the derivations of the bistability in the SP unit cell – are described in Supplementary Figure 1 and Note 2.
We design a hexagonal lattice by combining two stable states, such that the system breaks C6 symmetry but retains C3 symmetry (Fig. 1c). Only the bottom disk of each SP is connected with neighbouring SPs with springs (indicated with a torsional spring coefficient kcc). Note that this connection is a reverse spring, i.e., it induces opposite torque in the connected units (a similar setup can be found in a recent work22). Tunability comes from the fact that one can easily change the stable state of each SP—independently—to achieve a desired lattice configuration.
Band-inversion and topology
In this section, we evaluate dispersion characteristics of the system and observe a topological transition. For describing the dynamics of the (infinite) hexagonal lattice, we choose a periodic unit cell (highlighted in Fig. 1c), which consists of two SPs indexed as 1 and 2. Here, each SP can take either Y- or P-state by dial-in actions. Since a single SP has three DOFs, the unit cell would be represented by the following six parameters: [ϕ(1)b, ϕ(2)b, ϕ(1)t, ϕ(2)t, w(1)t, w(2)t].
First, we write the equations of motion for the periodic unit cell (index as i, j) as:
where I and m are the rotational inertia and the mass of the disks, respectively. kww, kϕϕ, kwϕ, and kϕw are the stiffness coefficients for the relative translation and rotations, and their coupling. The detailed expressions of these coefficients as a function of k1, k2, and geometric parameters are described in Supplementary Note 1.
For a lattice length of a, we invoke the Bloch’s theorem by using the periodicity in two directions: a1 = [1, 0]a and \({{\bf{a}}}_{2}=[\mathrm{1/2},\sqrt{3}\mathrm{/2}]a\), and obtain the following eigenvalue problem:
where ω is the angular frequency, and the generalized eigenvector \({\bf{U}}=[{{\varphi }}_{i,j}^{\mathrm{(1)}b},{{\varphi }}_{i,j}^{\mathrm{(2)}b},{{\varphi }}_{i,j}^{\mathrm{(1)}t},{{\varphi }}_{i,j}^{\mathrm{(2)}t},{w}_{i,j}^{\mathrm{(1)}t},{w}_{i,j}^{\mathrm{(2)}t}]\). B and M are the stiffness and mass matrices, respectively (see the detailed expressions in Supplementary Note 3).
There are two possible configurations of the C3 symmetric hexagonal unit cell: Y-P configuration and P-Y configuration. Figure 2 displays the dispersion properties and associated band-inversion when one state is transformed to the other. Due to the breakage of the inversion symmetry, a complete band gap emerges at the K point between the fifth and the sixth bands (see the highlighted red and blue bands in Fig. 2a,b. For details about Hamiltonian analysis of the system, see Supplementary Note 3). Note that these bands would have a degeneracy at the K point if the inversion symmetry is not broken (see the blue dashed lines). Although the dispersion curves for these two Y-P and P-Y configurations look similar, there is a difference in terms of the topology. The highlighted bands are inverted in these configurations — so-called band-inversion. We verify this by plotting in the left columns of Fig. 2c,d the mode shapes of the unit cell corresponding to the points K1 (744.5 Hz) and K2 (839.8 Hz) marked in the dispersion relations. For the Y-P configuration in Fig. 2c, we see that the low frequency vibration (K1 point) corresponds to the case when only the P-state is vibrating in the lattice. In Fig. 2d, the P-state vibrates in the P-Y configuration at the low frequency in the same way. This makes sense as the designed stiffness for the P-state is lower than that of the Y-state (see Supplementary Note 2). However, there is an inversion in terms of where in the unit cell the vibration is dominant due to the filpping of the Y- and P-states.
The aforementioned band-inversion resembles the one seen in the valley Hall effect. We can calculate the valley Chern number in order to track the topological transition associated with this effect. This is achieved by integrating its Berry curvature over half of the first Brillouin zone. Mathematically, the valley Chern number \({C}^{K(K^{\prime} )}=(\mathrm{1/2}\pi )\iint \varOmega ({\bf{k}})dk\), where the Berry curvature \({\Omega }({\bf{k}})=i{\sum }_{v=\mathrm{1,}v\ne u}^{6}[\langle {\bf{u}}|\partial {\bf{B}}/\partial {{k}}_{x}|{\bf{v}}\rangle \langle {\bf{v}}|\partial {\bf{B}}/\partial {k}_{y}|{\bf{u}}\rangle -c\mathrm{.}c\mathrm{.}]/\) \({({\omega }_{v}^{2}-{\omega }_{u}^{2})}^{2}\)25. Here, i is the imaginary unit, c.c. denotes complex conjugate, 〈·|·〉 represents the inner product, k = [kx, ky] is the wave vector, and ωu and ωv are the angular frequencies corresponding to the normalized eigen vectors u and v, respectively. The calculated Berry curvature in the first Brillouin zone is shown in the right columns of Fig. 2c,d. One notices that it is localized at K and K′ points in the Brillouin zone, and it changes its sign as we alter from the Y-P to the P-Y configuration—reflecting the band-inversion process. Therefore, the calculated valley Chern numbers CK (or CK′) for the fifth and the sixth bands of the Y-P configuration (highlighted red and blue bands in Fig. 2a) are −1/2 and 1/2 (or 1/2 and −1/2), respectively. These are reversed for the P-Y configuration, and this confirms that the two configurations are topologically distinct. The quantized difference of the valley Chern numbers of the two configurations, i.e., \(|{C}_{{\rm{Y}}-{\rm{P}}}^{K}-{C}_{{\rm{P}}-{\rm{Y}}}^{K}|=1\), indicates the emergence of a topologically protected edge state at the interface if these configurations are placed adjacently.
Topological defect and its manipulation
In this section, we will show how a topological defect can be created by placing topologically distinct lattices, P-Y (defined hereafter to be type-I for the sake of simplicity) and Y-P (type-II), adjacently. We will also show that this topological defect can easily be reconfigured to any other shapes—thanks to the extreme tunablity of the system. First, we confirm the existence of topologically protected interface modes for a linear topological defect (see Fig. 3a). To this end, we take a supercell of size 1 × 20 with the top and the bottom boundaries fixed, and we apply the periodic boundary condition in the x-direction.
The resulting dispersion of the supercell strip is plotted in Fig. 3b. We notice several bulk modes (curves in black color). These correspond to the bulk bands seen in the unit cell analysis done earlier (Fig. 2a,b). However, we also note some additional modes (dashed red and blue curves in Fig. 3b). In blue color are the two overlapping modes that appear at the top and the bottom of the supercell due to the identical boundaries on both sides. However, there is a distinguished mode (red color) inside the band gap. This corresponds to the interface mode emerging due to the distinct topological nature of the lattices I and II. Additionally, to the extreme top of the dispersion curve, we do observe another interface mode (red color) outside the cutoff frequency.
Now that we have shown the framework of creating a topological defect, it is also possible to achieve various complex shapes of the topological interfaces in a 2D lattice by strategic dial-in actions of the SP cells. In Fig. 3c–e, we assemble some of these shapes with various bends, showcasing the manipulation capability in the system. Below are the plots, obtained from the numerical experiments (see methods) for a harmonic excitation at 760 Hz applied to the 40 × 40 lattice. This frequency excitation, being inside the band gap, excites the topologically protected mode, and thus demonstrates a robust energy transport through various interfaces.
Topological vs. traditional waveguides
It is now natural to ask — in what ways the topological waveguide different from a traditional waveguide? Here, by a traditional waveguide, we refer to a waveguide that is created without incurring topological disparities in the same system. One way to create such a waveguide is by introducing a topologically trivial defect along the desired wave path so as to utilize the localized defect modes for wave transmission29. Figure 4a,b show the exemplary cases of topological and traditional waveguides, respectively, realized in the same SP settings. Note that given the initially uniform C3 symmetric hexagonal structure, we can achieve the creation of the traditional defect simply by transforming P-states into Y-states (i.e., in situ dial-in action) along the desired wave path (see the inset of Fig. 4b). However, the creation of the topological defects in the originally uniform lattice requires more actions, since it necessitates the border between the type-I and the type-II lattices. That is, we need to convert the one side of the SP cells (i.e., the upper side of the lattice with respect to the wave path in Fig. 4a) from the type-I to the type-II lattice, which demands the whole flipping (i.e., dial-in action) of the SP cells from the Y- to P-state and vice versa. The analogous operation in 1D lattice systems has been investigated by Chaunsali et al.24. The advantage of our system is that it can realize both types of traditional and topological waveguides in the same system by leveraging the bistable SP network and the in situ dial-in action on it. This provides an excellent opportunity to compare their transmission properties.
We perform an eigen analysis on a 40 × 40 structure (with 9600 DOF in total) for both types of waveguide structures. In Fig. 4c,d, we plot the eigen frequencies against the modal order for the topological and traditional waveguides, respectively. The blue and yellow curves correspond to the bulk bands, highlighted in the unit cell dispersion in Fig. 2a,b. Sandwiched between these two branches are the modes localized at the waveguide interfaces (red color, as magnified in the insets). We observe that the topological waveguide ensures that the entire band gap is populated by the interface modes. This affirms our observations in the previous sections where a robust transmission was shown along topological interfaces. The traditional waveguide, however, does not lead to the modes spanned over the entire band gap (Fig. 4d)—indicating its limitations in terms of constructing a wide range of defect modes. For the corresponding eigen shapes, see Supplementary Movies 1 and 2.
The aforementioned characteristics provide us with a deep insight into the differences of the topological and traditional waveguides, and these are now used to explain different transmission spectra along the waveguide channels. We perform numerical simulations and calculate the transmission spectra for a range of input frequencies (see methods). In Fig. 4e, we plot the obtained transmission. We can immediately notice a clear difference in the transmission inside the band gap (i.e., 744.5 Hz to 839.8 Hz). The topological waveguide leads to a superior transmission all along the band gap, however, the traditional waveguide yields a significant transmission only in a small range of frequencies (Δf). This transmission limited to a small frequency window is due to the presence of the defect modes, previously shown in Fig. 4d.
Even though the topological waveguide shows a superior transmission overall for the frequencies inside the band gap, we investigate if it has any qualitative differences from the traditional waveguide for the small range of frequencies (Δf in Fig. 4e). To answer this question, we perform a numerical experiment on the waveguides by sending a 50 ms long Gaussian packet at a frequency (757 Hz) lying inside the range of interest Δf. In Fig. 5, we compare the transient responses for topological and traditional waveguides. We observe that the topological waveguide in Fig. 5a shows that the wave packet does not back scatter at the multiple sharp bends, and it smoothly travels along the path. However, the traditional waveguide in Fig. 5b indicates the presence of scattering around the bends. Note that the wave packet still propagates along the path and would lead to a significant transmission as shown in Fig. 4e. Nonetheless, it is qualitatively different from the topological waveguide in terms of guiding a wave packet by allowing back scattering around bends. The difference of wave transmission efficiency between the traditional and topological waveguides is further investigated systematically for bends of various angles in Supplementary Figures 2 ∼ 4 and Note 4.
One-way waveguide
Lastly, we demonstrate that a topological waveguide constructed through our system can support one-way wave propagation if a valley-selective excitation is given at the source. To this end, we first extract the amplitude and phase information of the topologically protected mode from the supercell analysis done earlier (Fig. 3a,b). In Fig. 6a,b, we calculate the amplitude ratio (i.e., A1/A2) and phase difference (φ1 − φ2) of the bottom disks’ rotations between the Y-and P-states at the topological interface (see insets), and plot them as a function of reduced wavevector (kx) in the bandgap range. We observe that the trend can be categorized into two valleys. One corresponds to the forward propagation (data points indicated with the subscript F in Fig. 6a,b), and the other to the backward propagation (subscript B). These can be verified by looking at the slope (i.e., group velocity) of the protected mode (red color) in Fig. 3b. In this way, appropriate amplitude ratio and phase difference can be applied (i.e., valley-selection at either K or K′) to the disks at the interface to excite either forward or backward propagating waves. This is confirmed by a transient analysis performed at 778 Hz in Fig. 6c. If the lattice is excited in the middle point (marked with a star) with the amplitude of A1/A2 = 1.748 and the phase difference of φ1 − φ2 = 0.38π, we observe a forward propagating wave (left panel in Fig. 6c). However, if the excitation with the same amplitude but opposite phase (i.e., φ1 − φ2 = −0.38π) is applied, we observe a backward propagating wave (right panel). See Supplementary Movies 3 and 4 for more details. These numerical results attest that the bistable SP-based metamaterial system proposed in this study allows not only the in situ manipulation of wave paths via dial-in actions, but also a selective one-way propagation of mechanical waves by strategic excitations.
Discussion
Here, we propose a dial-in topological metamaterial system based on the bistable Stewart Platform (SP) and report robust one-way propagation of mechanical waves in it along tailorable wave paths. By arranging the bistable SP cells hexagonally in an alternating fashion, we can create two types of topologically distinctive lattices, which can be transformed to each other simply by a dial-in action. We prove that this transformation changes the topology of the system—quantified by the valley Chern numbers. When lattices with these two topologically distinct configurations are placed adjacently, we show the existence of a topologically protected mode at the interface. This idea is extended to tune the system in situ to create variety of waveguides, and we demonstrate a robust energy propagation along them using numerical simulations. We conduct eigenmode analysis and transient simulations of finite structures to highlight some key differences between topological and traditional waveguides in the same system. While the traditional waveguides also lead to significant wave transmission due to interfacial local modes inside the band gap, the edge modes generated in the topological waveguides are qualitatively different in that they support a wider range of frequencies and are immune to back scattering at sharp bends in the structure. We also show the strategy of giving valley-selective excitation to the system such that one-way wave propagation is achieved along the waveguide. Therefore, this tunable system opens up possibilities to realize various complex shapes of topological waveguides without resorting to external fields or adding/removing the masses from the system. Further studies including the experimental verification of the proposed tunable metamaterials would be reported in authors’ future publications.
Methods
Numerical experiment
We employ the Runge-Kutta method (step size =10−4 s) to get the response at any time instant for a variety of input signals: harmonic, Gaussian pulse, and sinusoidal frequency sweep.
Calculation of the transmission spectrum
We perform a numerical experiment and calculate the transmission spectra. A sweep frequency signal (20 Hz to 1000 Hz in 5 s) is used as a rotational perturbation applied to the bottom disk at the input location. The transient rotation of the bottom disk is measured at the output location. Thus, the transmission \(T(\omega )=20\,\log [{\varPhi }_{output}^{b}(\omega )/{\varPhi }_{input}^{b}(\omega )]\), where Φ(ω) represents the power spectral density (PSD) of the transient rotation ϕ(t) of the disk.
Data availability
The data that support the findings of this study are available from the corresponding author upon request.
Change history
10 January 2020
An amendment to this paper has been published and can be accessed via a link at the top of the paper.
References
Hasan, M. Z. & Kane, C. L. Colloquium: topological insulators. Rev. Mod. Phys. 82, 3045 (2010).
Qi, X. L. & Zhang, S. C. Topological insulators and superconductors. Rev. Mod. Phys. 83, 1057–1110 (2011).
Thouless, D. J. Quantization of particle transport. Phys. Rev. B 27, 6083–6087 (1983).
Klitzing, K. The quantized Hall effect. Quantization of particle transport. Rev. Mod. Phys. 58, 519 (1986).
Kane, C. L. & Mele, E. J. Quantum spin Hall effect in graphene. Phys. Rev. Lett. 95, 226801 (2005).
Xiao, D., Yao, W. & Niu, Q. Valley-contrasting physics in graphene: magnetic moment and topological transport. Phys. Rev. Lett. 99, 236809 (2007).
Lu., L., Joannopoulos, J. D. & Soljačić, M. Topological photonics. Nat. Photon. 8, 821–829 (2014).
Khanikaev, A. B., Fleury, R., Mousavi, S. H. & Alù, A. Topologically robust sound propagation in an angular-momentum-biased graphene-like resonator lattice. Nat. Commun. 6, 8260 (2015).
Yang, Z. et al. Topological acoustics. Phys. Rev. Lett. 114, 114301 (2015).
Chen, Z. G. & Wu, Y. Tunable topological phononic crystals. Phys. Rev. Appl. 5, 054021 (2016).
He, C. et al. Acoustic topological insulator and robust one-way sound transport. Nat. Phys. 12, 1124–1129 (2016).
Zhang, Z. et al. Topological Creation of Acoustic Pseudospin Multipoles in a Flow-Free Symmetry-Broken Metamaterial Lattice. Phys. Rev. Lett. 118, 084303 (2017).
Lu, J., Qiu, C., Ke, M. & Liu, Z. Valley vortex states in sonic crystals. Phys. Rev. Lett. 116, 093901 (2016).
Lu, J. et al. Observation of topological valley transport of sound in sonic crystals. Nat. Phys. 13, 369–374 (2017).
Huber, S. D. Topological mechanics. Nat. Phys. 12, 621–623 (2016).
Nash, L. M. et al. Topological mechanics of gyroscopic metamaterials. Proc. Natl. Acad. Sci. USA 112, 14495–14500 (2015).
Wang, P., Lu, L. & Bertoldi, K. Topological phononic crystals with one-way elastic edge waves. Phys. Rev. Lett. 115, 104302 (2015).
Chaunsali, R., Li, F. & Yang, J. Stress Wave Isolation by Purely Mechanical Topological Phononic Crystals. Sci. Rep. 6, 30662 (2016).
Ong, Z. Y. & Lee, C. H. Transport and localization in a topological phononic lattice with correlated disorder. Phys. Rev. B 94, 134203 (2016).
Süsstrunk, R. & Huber, S. D. Observation of phononic helical edge states in a mechanical topological insulator. Science 349, 47–50 (2015).
Mousavi, S. H., Khanikaev, A. B. & Wang, Z. Topologically protected elastic waves in phononic metamaterials. Nat. Commun. 6, 8682 (2015).
Pal, R. K., Schaeffer, M. & Ruzzene, M. Helical edge states and topological phase transitions in phononic systems using bi-layered lattices. J. Appl. Phys. 119, 084305 (2016).
Chaunsali, R., Chen, C. W. & Yang, J. Subwavelength and directional control of flexural waves in plates using topological waveguides. arXiv preprint arXiv 1708, 07994 (2017).
Chaunsali, R., Kim, E., Thakkar, A., Kevrekidis, P. G. & Yang, J. Demonstrating an in situ topological band transition in cylindrical granular chains. Phys. Rev. Lett. 119, 024301 (2017).
Pal, R. K. & Ruzzene, M. Edge waves in plates with resonators: an elastic analogue of the quantum valley Hall effect. New J. Phys. 19, 025001 (2017).
Liu, T. W. & Semperlotti, F. Acoustic Valley-Hall Edge States in phononic elastic waveguides. arXiv preprint arXiv 1708, 02987 (2017).
Wu, Y., Yu, K., Jiao, J. & Zhao, R. Dynamic modeling and robust nonlinear control of a six-DOF active micro-vibration isolation manipulator with parameter uncertainties. Mech. Mach. Theory 92, 407–435 (2015).
Dasgupta, B. & Mruthyunjaya, T. S. The Stewart platform manipulator: a review. Mech. Mach. Theory 35, 15–40 (2000).
Khelif, A., Choujaa, A., Benchabane, S., Djafari-Rouhani, B. & Laude, V. Guiding and bending of acoustic waves in highly confined phononic crystal waveguides. Appl. Phys. Lett. 84, 4400–4402 (2004).
Acknowledgements
The authors are grateful to Rui Zhu, Linyun Yang, and Xiaotian Shi for fruitful discussions. R.C., H.Y., and J.Y. are grateful for the financial support from the U.S. National Science Foundation (CAREER-1553202 and EFRI-1741685). Y.W. and K.Y. acknowledge the support from the Harbin Institute of Technology and the China Scholarship Council (Grant No. 201606120065).
Author information
Authors and Affiliations
Contributions
Y.W., J.Y., and K.Y. conceived the original idea. Y.W. performed the numerical simulations. H.Y. calculated the bistable characteristic of SP. Y.W. and R.C. analyzed the results and wrote the manuscript. J.Y. and K.Y. supervised the project.
Corresponding authors
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Wu, Y., Chaunsali, R., Yasuda, H. et al. Dial-in Topological Metamaterials Based on Bistable Stewart Platform. Sci Rep 8, 112 (2018). https://doi.org/10.1038/s41598-017-18410-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-017-18410-x
This article is cited by
-
Heterogeneous origami-architected materials with variable stiffness
Communications Materials (2021)
-
Anticancer and Apoptotic-Inducing Effects of Rutin-Chitosan Nanoconjugates in Triple Negative Breast Cancer Cells
Journal of Cluster Science (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.