Nowadays, optical tweezers have undergone explosive developments in accordance with a great progress of lasers. In the last decade, a breakthrough brought optical tweezers into the nano-world, overcoming the diffraction limit. This is called plasmonic optical tweezers (POT). POT are powerful tools used to manipulate nanomaterials. However, POT has several practical issues that need to be overcome. First, it is rather difficult to fabricate plasmonic nanogap structures regularly and rapidly at low cost. Second, in many cases, POT suffers from thermal effects (Marangoni convection and thermophoresis). Here, we propose an alternative approach using a nano-structured material that can enhance the optical force and be applied to optical tweezers. This material is metal-free black silicon (MFBS), the plasma etched nano-textured Si. We demonstrate that MFBS-based optical tweezers can efficiently manipulate small particles by trapping and binding. The advantages of MFBS-based optical tweezers are: (1) simple fabrication with high uniformity over wafer-sized areas, (2) free from thermal effects detrimental for trapping, (3) switchable trapping between one and two - dimensions, (4) tight trapping because of no detrimental thermal forces. This is the NON-PLASMONIC optical tweezers.
Recently, there has been rapid development in plasmonics1,2,3,4,5. The electric-field-enhancement effect of plasmon can be employed as an optical force to trap a small nano/micro-object with great efficiency. It is called plasmonic optical nano-tweezers (POT)6,7,8,9. Most POT realisations are based on “gap-mode” surface plasmons, with which the electric field of the incident light (and accordingly the optical force) can be amplified by a factor of >103 10. While POT is a powerful tool with number of advantages compared with conventional optical tweezes11,12,13,14, there are some obstacles to further development. First, it is rather difficult to fabricate such plasmonic nanogap structures (i.e., the plasmonic dimer geometry) with high reproducibility and uniformity over large areas at low cost. Electron beam lithography10,15,16 is forbiddingly expensive and angular-resolved nanosphere lithography (ARNSL)17,18,19 needs complicated procedures. Second, gold and silver, which are the typical materials used in plasmonics, are expensive and increase number of processing steps for POT devices. Thus, these limitations will possibly hinder the further development of POT.
Furthermore, we and other groups previously showed that local heat generation accompanying POT cannot be regarded as negligible and that it acts as a repulsive force seriously affecting POT10,20,21,22,23. Although the temperature rise (ΔT) by plasmon excitation is not large, several tens of Kelvins frequently generate a huge temperature gradient (\(\nabla T\)) around the area: \(\nabla T\)≈1 K/μm. Such a huge temperature gradient leads to transport of nanoparticles and molecules along the temperature gradient (thermophoresis)24,25,26. In addition, thermal convection (Marangoni flow) always takes place in such situations, making the trapping behavior complex. Thus, suppression and control of the thermal forces are indispensable if POT is to progress.
Here, we present an alternative approach using a nano-structured material that can enhance the optical force. This approach uses a metal-free black silicon (MFBS) made by plasma etching27,28,29,30,31,32. Generally the surface of black silicon (BS) is completely covered with nano-protrusions. The optical reflection of BS is only a few percent over visible and near-IR spectral ranges due to the refractive index gradient around pyramidal nano-spikes28. Based on this unique non-reflecting BS platform, hence, enhanced absorbance, BS has the function of light harvesting and was used to produce high efficiency >21% solar cells30,31,32. One of the great advantages of BS is that the fabrication procedure for the nanotextured surfaces can be extended over large areas. Furthermore, we recently showed that MFBS has a small enhancement effect of electric field (E) of light with a factor of <5 in E 2 33. The origin of this enhancement is due to a multiple light scattering resulting in a light localisation predominantly between the pyramidal pillars. In this study, by overcoming the listed disadvantages of POT, we demonstrate that MFBS-based optical tweezers can be used to efficiently manipulate small particles with characteristic behaviours of one and two-dimentional (1D/2D) switchable trapping and manipulation. We also showed that this optical trapping is not affected by thermal effects even at the used high intensity. This technique has various advantages, and is expected to open a new chapter in advanced optical trapping.
The trapped particles were fluorescent polystyrene nanospheres with diameters d = 500 nm dispersed in water. The trapping behavior was monitored using a fluorescence microscope. Prior to the optical trapping of polystyrene nanospheres using MFBS, we tested optical trapping using our conventional optical tweezers with a laser beam (808 nm laser diode) tightly focused by an oil-immersion objective lens (100 × , N.A. = 1.40). However, trapping was not stable even at the maximum output power of the laser, at which light intensity (I) reached 800 kW/cm2 at the focus. The threshold value of I (I tsd ) for stable trapping was estimated to be >1000 kW/cm2 for our conventional optical trapping system. POT using a ARNSL substrate for these polystyrene beads has previously been investigated and I tsd was evaluated to be ~ 1 kW/cm2 34. It is obvious that the value of I tsd for stable trapping is much less when the plasmonic effect is utilized.
We examined MFBS-assisted optical trapping of polystyrene beads using the same optical trapping system as the conventional optical tweezers and POT noted above. Figure 1(a–d) shows the results of an experiment with the polystyrene beads; a series of optical micrographs (fluorescence images) at various times, t, after switching on light irradiation (808 nm LD) with an intensity, I, of 320 kW/cm2 focused on the surface of the MFBS. A scanning electron microscopy (SEM) image of the MFBS used here, which was fabricated by 15 min dry etch of Si in SF6/O2 plasma, is also shown in Fig. 1(e). The height of nano-pillar was 250 nm on average and the diameter was 40–240 nm35. Fig. 1(b–d) clearly show trapping of polystyrene beads at the illuminated area (marked by a circular dashed-line) on the surface. The polystyrene beads were trapped one by one after the start of illumination, and the number reached 8 at t = 60 s. The particles were assembled on the surface of the MFBS, meaning this was a 2D-trapping. When the illumination was stopped, these trapped beads were immediately released, and spread out from the area by Brownian motion. When we replaced the MFBS with a simple glass or silicon substrate, no sign of trapping was observed at the same value of I (irradiation intensity) . This clearly shows the efficient optical trapping on MFBS.
A video of the above described behavior is given in the supplement information (SI) section. Although hardly apparent in the micrographs (Fig. 1), the movie revealed a unique characteristic of the trapping. In POT (see a movie in SI), the transport of a microparticle to a metallic nanostructure from some distance by Marangoni convection due to local plasmonic heating has frequently been observed20,34,36. However, no such transportation was observed in the present case with MFBS, confirming a thermal-effect-free character of trapping. As derived below, we estimated temperature elevation by laser irradiation on the substrates.
Figure 2 shows the dependence of the trapping polystyrene beads on MFBS on I . Below I = 30 kW/cm2, no sign of trapping was found. At I = 30 kW/cm2 (Fig. 2(a)), trapping of a single nanosphere in the irradiated area can clearly be seen. This means that the value of I tsd for MFBS-assisted optical trapping is ca. 30 kW/cm2. This is much lower than that for conventional optical trapping (I tsd ~ 1000 kW/cm2), and higher than that for POT (I tsd ~ 1 kW/cm2) for the same particles34,37,38,39. That is, we were able to verify that enhancement of the optical force by MFBS greatly assists optical trapping, although the degree of enhancement is lower than that for POT.
As I increases, 2D-trapping with an increasing number of trapped particles can be observed on the surface of the MFBS (Fig. 2 (b,c)), indicating that the trapping potential (U) becomes deeper with increasing I. This result also signifies the important fact that optical trapping can be accomplished using a wide range of I from 30 to 740 kW/cm2 (Trapping at 740 kW/cm2 is 1D-trapping as described later). Note that the maximum value of I (740 kW/cm2 focused on 1 μm2) was the limit of our laser source and that trapping would be possible using even more intense irradiation. Such behavior is in contrast to POT, where stable trapping is possible only over a narrow range of I. For instance, ARNSL-based POT for the same polystyrene beads is possible only when 1 < I < 5 kW/cm2 34. Stable trapping is no longer possible when I > 5 kW/cm2. This is prevented by thermal effects: thermophoresis and Marangoni convection. To reiterate, we suggest that MFBS-assisted optical trapping is free from thermal disturbance.
In the aforementioned optical trapping, a 2D assembly of polystyrene nanospheres on the MFBS substrate was achieved and the site where they were trapped was circular in shape with d = 3 μm. Next, we show that the trapping behavior can be switched from the 2D-mode to a 1D-mode just by reducing the trapping site to 1 μm2. Figure 3 shows a series of optical micrographs for such trapping of polystyrene beads. In the early stage of irradiation, a single particle (marked by a white arrow in the figure) was stably trapped with no fluctuation in the illuminated area (Fig. 3(c)). When another particle (marked by a yellow arrow) happened to pass the illuminated area (Fig. 3(d,e)), it was trapped not next to the particle trapped first but on the top of it (Fig. 3(f)). This 1D trapping behavior, the “snowman structure formation” as illustrated in the figure, is shown by an increase in brightness of the fluorescence at the site (Fig. 3, from (c) to (f)).
Upon maintaining the irradiation, a third particle (marked by a purple arrow) was trapped not next to the two particles but on top of the second trapped (Fig. 3(g–i)), as illustrated. The second or third particle were presumably fluctuate with respect to the adjacent particle, leading to the slight growth in fluorescence of the trapped particles ((c) -(f)- (i) in Fig. 3). The trapping behavior shown in Fig. 3 can more clearly be seen in the video of the supplement. Figure 4 shows a temporal profile of the fluorescence intensity (FI) during 1D trapping, recorded at the center of the irradiated area. It is clear that FI is well correlated with the trapping behavior. FI abruptly increases just at the start of irradiation, corresponding to the first trapped bead. After a few seconds, there is an approximately 2-fold increase in FI corresponding to the second trapped bead. By continuing irradiation, FI remains almost constant, while a third was frequently trapped during this period. The fluorescence when a third particle was trapped barely increased due to shielding of light to the particles. A vertical 1D-trapping of 3 particles along with the optical axis can be achieved, which is a peculiar and unique to MFBS-assisted trapping/binding.
Examination of all the experimental results presented here strongly implies that thermal effects are almost negligible in MFBS-assisted trapping. To explore this further, we quantitatively evaluated the temperature distribution around the excitation area during irradiation at 808 nm by means of spatially-resolved fluorescence microspectroscopy. The sample was a Tris-buffer solution of a probe dye (2′,7′-bis(2-carboxyethyl)-5-(6)-carboxyfluorescein) (BCECF), which has a fluorescence intensity very sensitive to temperature40,41. The fluorescence intensity of the dye decreases by 10% when the temperature increases by 15 K (see the Supplement). Using this technique, we precisely determined the rise in temperature of the irradiated area on MFBS surface. Our results showed that the fluorescence intensity of the dye was not affected by irradiation at 808 nm, indicating that the rise in temperature (ΔT) was negligible (ΔT ~ 0, and hence the gradient \(\nabla T\approx 0\)) over a wide range of I (0 < I < 320 kW/cm2). These data are also available in the Supplement. This is reasonable since crystalline silicon has an increasingly smaller optical absorption at wavelengths (λ > 800 nm) and a good thermal conductivity. Thus, we verified that the present MFBS-assisted optical trapping is completely free from thermal effects which are detrimental for a stable trapping.
Before we discuss the trapping mechanism, we evaluated the trap stiffness (i.e. how tightly the particle is trapped on the surface) on MFBS comparing with POT. Figure 5 shows trajectories of trapped particles for POT using ARNSL as a reference (Fig. 5(a))34 and the present MFBS-assisted trapping (Fig. 5(b) and (c), corresponding to Fig. 1 and 3, I = 320 kW/cm2). As seen in the Fig. 5(a) for POT, trapped particles were fluctuated on a ARNSL surface over ca. 1 μm within 1.0 s. This implies that trapping force is not much higher than but marginal to Brownian motion. As we previously pointed out, both the plasmon-enhanced optical force (attractive force) and the thermophoretic force (repulsive force) lay in the order of sub-pN42. They should cancel with each other, resulting in a small attractive force and hence the fluctuation seen in Fig. 5(a). On the other hand, it is obvious that such fluctuation was much suppressed in MFBS-assisted trapping (Fig. 5(b)). Trapped particles were fluctuated on a MFBS surface within ca. 0.5 μm. In particular, when we reduce the irradiation spot size (corresponding to Fig. 3), fluctuation of the trapped particles is negligible (Fig. 5(c)). Namely, the MFBS-assisted trapping is much tighter than POT (stiffness is strong). For this tight trapping, we can evaluate a spring constant k obeying Hooke’s law in the trapping potential by analyzing displacement of the particle from the center (Δx or Δy). As explained in the supplement, we obtained the value of k = 67 pN/nm at 1 W light intensity. This value is considerably larger than that of conventional optical tweezers (it ranges in the order of 10−6−100 pN/nm for submicron~micron-sized polymer beads). This means that stiffness of the MFBS trapping is much high (a tight trapping). Such tighter grip would also contribute to the 1D-trapping.
Next, the mechanism underlying the demonstrated trapping is discussed. The origin of the MFBS-assisted optical trapping is an effect of multi-scattering of the incident light which is additionally enhanced in the case of close proximity of a bead. The spatial distribution of electric field intensity of light around the surface of MFBS was calculated in the absence and presence of the polystyrene beads. Figure 6 shows the results of finite-difference time-domain (FDTD) simulation. In the absence of a particle (Fig. 6(a)), the enhancement effect is very small and is limited to the surface of the MFBS. By contrast, when the particle is placed on the surface, the electric field intensity (E 2) is significantly enhanced at the contact location (Fig. 6(b)). This strongly suggests that the origin of the enhancement is analogous to SIBA (self-induced back action)39,43,44 observed in plasmonic trapping. The SIBA effect would result in the stable trapping seen in Figs. 1~3. The enhanced electric field around a trapped particle is modified45, and can facilitate a 1D-trapping, the tendency recognizable in Fig. 3. Figure 3(c) shows a simulation result for 1D-trapping - a snowman structure. The electric field is slightly enhanced at the interface between two particles. It is also revealed that the first particle is stronger gripped on the MFBS surface by the presence of the second particle. This SIBA-like action contributes to the tight 1D-trapping – the snowman structure.
It should be noted, that the presented FDTD modeling is for a plane wave illumination and it is not capturing focusing as well as nonlinear effects which begin to be important at high intensities; also, optical aberrations strongly dependent on the actual optics used and usually favors axially elongated focal volumes. Since polystyrene has a slightly larger refractive index than water, any bead entering 1D trapping geometry will facilitate to create light concentration due to locally augmented refractive index. This explains qualitatively well the observed 2D and 1D trapping.
Finally, we describe advantages of MFBS-assisted optical trapping. It is easy to fabricate MFBS as compared to plasmonic nanogap structures. Accordingly, rapid fabrication over a large area is possible at much lower cost than plasmonic structures. Since MFBS-assisted optical trapping is never accompanied by real electronic excitation of silicon when λ > 800 nm, it is free from thermal effects and does not suffer from thermophoresis and Marangoni convection. Thus, while POT is possible only over a narrow range of intensities I (1–5 kW/cm2 for 500 nm polystyrene beads for POT using an AR-NSL substrate34) due to these thermally induced localized flows, a more intense irradiation is available for MFBS-assisted optical trapping (MW/cm2) and opens a unexplored area of material behavior in strongly localized high intensity light fields. Such situation would enable a nonlinear optical trapping46 and new applications. Furthermore, while the wavelength of the light for POT is limited to a resonant plasmon band, a wide wavelengths spectrum can be used for MFBS-assisted optical trapping because anti-reflection action of tapered pyramids is inherently broadband. The switchable trapping between 1D- and 2D-trapping is also a unique feature of MFBS-assisted optical trapping.
On the other hand, MFBS has been believed to show no enhancement effect for optical trapping. It should be noted that Kotsifaki et al. has very recently reported POT using metal-coated BS (MCBS) (metal; gold)47. MCBS is an intriguing novel plasmonic material which is easy to fabricate35,48,49. The plasmonic functions of MCBS such as surface-enhanced Raman scattering (SERS) have been examined by several research groups, including ours35,48. Kotsifaki et al. fabricated black-Si on a Si wafer by means of femtosecond pulsed laser processing50,51. They quantitatively analysed trapping force and thermal effect on MFBS substrate, and showed that trapping efficiency for 400 nm polystyrene beads on the MFBS substrate was one order of magnitude higher than that on the flat silicon substrate50. Furthermore, optical trapping efficiency became higher by coating Au/Cu on the MFBS substrate, indicating evanescent plasmonic enhancement. Recently, they developed MCBS(gold-coated black silicon) assisted optical trapping, showing wavelength-dependent characterization of the trapping47. They fabricated BS by means of ultrafast (fs) laser processing which provides a slightly different morphology with rounded tips, while we employed dry etching which results in nano-sharp pyramidal surface texture. This indicates performance of MFBS-assisted optical trapping is sensitive to the actual nanostructure of silicon surface.
In conclusion, we succeeded in the MFBS-assisted optical trapping and binding of polymer nanospheres. The origin of this trapping phenomenon is multiple scattering and a SIBA-like effect which is demonstrated for dielectric (non-plasmonic) structure for the first time. MFBS-assisted optical trapping and binding have several advantages as compared with POT. Moreover, although MFBS-assisted trapping has a weaker optical force as compared to POT, MFBS-assisted trapping can perform tighter trapping than POT because it is free from the detrimental thermal effects. Namely, the total trapping force of MFBS-trapping should be higher than that of POT. By optimizing the surface nanostructure it should be possible to realize stiffer traps optimized for specific wavelengths. MFBS-assisted optical trapping mean that it can potentially be developed and applied to the manipulation of a variety of nanomaterials. MFBS-assisted optical trapping and POT should play complementary roles in the future manipulation of nanomaterials and research of nanoscale temperature and optical nonlinearities.
The experimental methods are described in the Supplement information. Briefly, observation of POT was carried out using a fluorescence microscope, the details of which have previously been described elsewhere34,37,42,52. Near-infrared (NIR) laser light (λ = 808 nm) and visible laser light were used for trapping and fluorescence excitation, respectively. These laser beams were introduced co-axially into an inverted optical microscope to irradiate the sample solution. We carried out optical trapping on a surface of a substrate, since trapping force decreased of large distance from the surface50. Fluorescence from the dye solution was detected with a photodetector (a spectrometer with a cooled CCD camera). All the experiments were carried out at room temperature under ambient conditions.
Kühler, P. et al. Plasmonic DNA-Origami Nanoantennas for Surface-Enhanced Raman Spectroscopy. Nano Lett. 14, 2914–2919 (2014).
Zhong, Y. et al. Plasmon-assisted water splitting using two sides of the same SrTiO3 single-crystal substrate: Conversion of visible light to chemical energy. Angew. Chemie Int. Ed. 53, 10350–10354 (2014).
Galloway, C. M. et al. Plasmon-Assisted Delivery of Single Nano-Objects in an Optical Hot Spot. Nano Lett. 13, 4299–4304 (2013).
Lal, S., Link, S. & Halas, N. J. Nano-optics from sensing to waveguiding. Nat. Photon. 1, 641–648 (2007).
Simoncelli, S. et al. Quantitative Single-Molecule Surface-Enhanced Raman Scattering by Optothermal Tuning of DNA Origami-Assembled Plasmonic Nanoantennas. ACS Nano 10, 9809–9815 (2016).
Juan, M. L., Righini, M. & Quidant, R. Plasmon nano-optical tweezers. Nat. Photonics 5, 349–356 (2011).
Quidant, R. Plasmonic tweezers—The strength of surface plasmons. MRS Bull. 37, 739–744 (2012).
Shoji, T. & Tsuboi, Y. Plasmonic Optical Tweezers toward Molecular Manipulation: Tailoring Plasmonic Nanostructure, Light Source, and Resonant Trapping. J. Phys. Chem. Lett. 5, 2957–2967 (2014).
Shoji, T. & Tsuboi, Y. Plasmonic optical trapping of soft nanomaterials such as polymer chains and DNA: micro-patterning formation. Opt. Rev. 22, 137–142 (2015).
Grigorenko, A. N., Roberts, N. W., Dickinson, M. R. & Zhang, Y. Nanometric optical tweezers based on nanostructured substrates. Nat. Photon. 2, 365–370 (2008).
Ashkin, A., Dziedzic, J. M., Bjorkholm, J. E. & Chu, S. Observation of a single-beam gradient force optical trap for dielectric particles. Opt. Lett. 11, 288 (1986).
Arita, Y., Mazilu, M., Vettenburg, T., Wright, E. M. & Dholakia, K. Rotation of two trapped microparticles in vacuum: observation of optically mediated parametric resonances. Opt. Lett. 40, 4751 (2015).
Yuyama, K., Marcelis, L., Su, P.-M., Chung, W.-S. & Masuhara, H. Photocontrolled Supramolecular Assembling of Azobenzene-Based Biscalixarenes upon Starting and Stopping Laser Trapping. Langmuir 33, 755–763 (2017).
Kudo, T., Ishihara, H. & Masuhara, H. Resonance optical trapping of individual dye-doped polystyrene particles with blue- and red-detuned lasers. Opt. Exp. 25, 4655 (2017).
Tanaka, Y., Kaneda, S. & Sasaki, K. Nanostructured potential of optical trapping using a plasmonic nanoblock pair. Nano Lett. 13, 2146–50 (2013).
Zhang, W., Huang, L., Santschi, C. & Martin, O. J. F. Trapping and sensing 10 nm metal nanoparticles using plasmonic dipole antennas. Nano Lett. 10, 1006–1011 (2010).
Hulteen, J. C. Nanosphere lithography: A materials general fabrication process for periodic particle array surfaces. J. Vac. Sci. Technol. A 13, 1553–1558 (1995).
Haynes, C. L., McFarland, A. D., Smith, M. T., Hulteen, J. C. & Van Duyne, R. P. Angle-resolved nanosphere lithography: Manipulation of nanoparticle size, shape, and interparticle spacing. J. Phys. Chem. B 106, 1898–1902 (2002).
Takase, M. et al. Selection-rule breakdown in plasmon-induced electronic excitation of an isolated single-walled carbon nanotube. Nat. Photonics 7, 550–554 (2013).
Roxworthy, B. J., Bhuiya, A. M., Vanka, S. P. & Toussaint, K. C. Understanding and controlling plasmon-induced convection. Nat. Commun. 5, 3173 (2014).
Shoji, T., Kitamura, N. & Tsuboi, Y. Resonant Excitation Effect on Optical Trapping of Myoglobin: The Important Role of a Heme Cofactor. J. Phys. Chem. C 117, 10691–10697 (2013).
Niinomi, H. et al. Plasmonic Heating-Assisted Laser-Induced Crystallization from a NaClO3 Unsaturated Mother Solution. Cryst. Growth Des. 17, 809–818 (2017).
Babynina, A. et al. Bending Gold Nanorods with Light. Nano Lett. 16, 6485–6490 (2016).
Piazza, R. & Parola, A. Thermophoresis in colloidal suspensions. J. Phys. Condens. Matter 20, 153102 (2008).
Duhr, S. & Braun, D. Why molecules move along a temperature gradient. Proc. Natl. Acad. Sci. 103, 19678–19682 (2006).
Jiang, H.-R., Wada, H., Yoshinaga, N. & Sano, M. Manipulation of Colloids by a Nonequilibrium Depletion Force in a Temperature Gradient. Phys. Rev. Lett. 102, 208301 (2009).
Ivanova, E. P. et al. Bactericidal activity of black silicon. Nat. Commun. 4, 2838 (2013).
Nishijima, Y. et al. Anti-reflective surfaces: Cascading nano/microstructuring. APL Photonics 1, 76104 (2016).
Steglich, M. et al. The structural and optical properties of black silicon by inductively coupled plasma reactive ion etching. J. Appl. Phys. 116 (2014).
Yuan, H.-C. et al. Efficient black silicon solar cell with a density-graded nanoporous surface: Optical properties, performance limitations, and design rules. Appl. Phys. Lett. 95, 123501 (2009).
Garnett, E. & Yang, P. Light trapping in silicon nanowire solar cells. Nano Lett. 10, 1082–1087 (2010).
Oh, J., Yuan, H.-C. & Branz, H. M. An 18.2%-efficient black-silicon solar cell achieved through control of carrier recombination in nanostructures. Nat. Nanotechnol. 7, 743–748 (2012).
Komatsu, R. et al. Plasmonic photo-thermoelectric energy converter with black-Si absorber. Sol. Energy Mater. Sol. Cells 143, 72–77 (2015).
Shoji, T. et al. Reversible Photoinduced Formation and Manipulation of a Two-Dimensional Closely Packed Assembly of Polystyrene Nanospheres on a Metallic Nanostructure. J. Phys. Chem. C 117, 2500–2506 (2013).
Gervinskas, G. et al. Surface-enhanced Raman scattering sensing on black silicon. Ann. Phys. 525, 907–914 (2013).
Wang, K. & Crozier, K. B. Plasmonic trapping with a gold nanopillar. Chemphyschem 13, 2639–2648 (2012).
Shoji, T. et al. Plasmon-Based Optical Trapping of Polymer Nano-Spheres as Explored by Confocal Fluorescence Microspectroscopy: A Possible Mechanism of a Resonant Excitation Effect. Jpn. J. Appl. Phys. 51, 92001 (2012).
Roxworthy, B. J. et al. Application of plasmonic bowtie nanoantenna arrays for optical trapping, stacking, and sorting. Nano Lett. 12, 796–801 (2012).
Juan, M. L., Gordon, R., Pang, Y., Eftekhari, F. & Quidant, R. Self-induced back-action optical trapping of dielectric nanoparticles. Nat. Phys. 5, 915–919 (2009).
Garcés-Chávez, V. et al. Extended organization of colloidal microparticles by surface plasmon polariton excitation. Phys. Rev. B 73, 85417 (2006).
Duhr, S., Arduini, S. & Braun, D. Thermophoresis of DNA determined by microfluidic fluorescence. Eur. Phys. J. E 15, 277–86 (2004).
Toshimitsu, M. et al. Metallic-Nanostructure-Enhanced Optical Trapping of Flexible Polymer Chains in Aqueous Solution As Revealed by Confocal Fluorescence Microspectroscopy. J. Phys. Chem. C 116, 14610–14618 (2012).
Mestres, P., Berthelot, J., Aćimović, S. S. & Quidant, R. Unraveling the optomechanical nature of plasmonic trapping. Light Sci. Appl. 5, e16092 (2016).
Chen, C. et al. Enhanced optical trapping and arrangement of nano-objects in a plasmonic nanocavity. Nano Lett. 12, 125–132 (2012).
Kudo, T., Wang, S.-F., Yuyama, K. & Masuhara, H. Optical Trapping-Formed Colloidal Assembly with Horns Extended to the Outside of a Focus through Light Propagation. Nano Lett. 16, 3058–3062 (2016).
Jiang, Y., Narushima, T. & Okamoto, H. Nonlinear optical effects in trapping nanoparticles with femtosecond pulses. Nat. Phys. 6, 1005–1009 (2010).
Kotsifaki, D. G., Kandyla, M. & Lagoudakis, P. G. Plasmon enhanced optical tweezers with gold-coated black silicon. Sci. Rep. 6, 26275 (2016).
Asiala, S. M., Marr, J. M., Gervinskas, G., Juodkazis, S. & Schultz, Z. D. Plasmonic color analysis of Ag-coated black-Si SERS substrate. Phys. Chem. Chem. Phys. 17, 30461–7 (2015).
Chen, Y. et al. Improved SERS Intensity from Silver-Coated Black Silicon by Tuning Surface Plasmons. Adv. Mater. Interfaces 1, 1–9 (2014).
Kotsifaki, D. G., Kandyla, M. & Lagoudakis, P. G. Near-field enhanced optical tweezers utilizing femtosecond-laser nanostructured substrates. Appl. Phys. Lett. 107, 1–6 (2015).
Kotsifaki, D. G. et al. Optical tweezers with enhanced efficiency based on laser-structured substrates. Appl. Phys. Lett. 101, 011102 (2012).
Shoji, T. et al. Permanent Fixing or Reversible Trapping and Release of DNA Micropatterns on a Gold Nanostructure Using Continuous-Wave or Femtosecond-Pulsed Near-Infrared Laser Light. J. Am. Chem. Soc. 135, 6643–6648 (2013).
This work was supported by JGC-S Scholarship Foundation, and JSPS KAKENHI Grant Numbers JP26288011, JP16K17922, and JP16H06506/JP16H06507 in Scientific Research on Innovative Areas “Nano-Material Manipulation and Structural Order Control with Optical Forces”. SJ is grateful for a partial support via PLASENS Consortium FNR C15/MS/10459961 and the Australian Academy of Science Senior Fellowship for a research visit to Japan. FDTD simulations were performed on the swinSTAR supercomputer at Swinburne University of Technology.
The authors declare that they have no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Shoji, T., Mototsuji, A., Balčytis, A. et al. Optical tweezing and binding at high irradiation powers on black-Si. Sci Rep 7, 12298 (2017). https://doi.org/10.1038/s41598-017-12470-9