Single-molecule junctions have been extensively used to probe properties as diverse as electrical conduction1,2,3, light emission4, thermoelectric energy conversion5,6, quantum interference7,8, heat dissipation9,10 and electronic noise11 at atomic and molecular scales. However, a key quantity of current interest—the thermal conductance of single-molecule junctions—has not yet been directly experimentally determined, owing to the challenge of detecting minute heat currents at the picowatt level. Here we show that picowatt-resolution scanning probes previously developed to study the thermal conductance of single-metal-atom junctions12, when used in conjunction with a time-averaging measurement scheme to increase the signal-to-noise ratio, also allow quantification of the much lower thermal conductance of single-molecule junctions. Our experiments on prototypical Au–alkanedithiol–Au junctions containing two to ten carbon atoms confirm that thermal conductance is to a first approximation independent of molecular length, consistent with detailed ab initio simulations. We anticipate that our approach will enable systematic exploration of thermal transport in many other one-dimensional systems, such as short molecules and polymer chains, for which computational predictions of thermal conductance13,14,15,16 have remained experimentally inaccessible.
Subscribe to Journal
Get full journal access for 1 year
only $3.90 per issue
All prices are NET prices.
VAT will be added later in the checkout.
Tax calculation will be finalised during checkout.
Rent or Buy article
Get time limited or full article access on ReadCube.
All prices are NET prices.
The data that support the findings of this study are available from the corresponding authors on reasonable request.
Smit, R. H. M. et al. Measurement of the conductance of a hydrogen molecule. Nature 419, 906–909 (2002).
Nitzan, A. & Ratner, M. A. Electron transport in molecular wire junctions. Science 300, 1384–1389 (2003).
Xu, B. & Tao, N. J. Measurement of single-molecule resistance by repeated formation of molecular junctions. Science 301, 1221–1223 (2003).
Reecht, G. et al. Electroluminescence of a polythiophene molecular wire suspended between a metallic surface and the tip of a scanning tunneling microscope. Phys. Rev. Lett. 112, 047403 (2014).
Reddy, P., Jang, S. Y., Segalman, R. A. & Majumdar, A. Thermoelectricity in molecular junctions. Science 315, 1568–1571 (2007).
Cui, L. et al. Peltier cooling in molecular junctions. Nat. Nanotechnol. 13, 122–127 (2018).
Garner, M. H. et al. Comprehensive suppression of single-molecule conductance using destructive σ-interference. Nature 558, 415–419 (2018).
Miao, R. et al. Influence of quantum interference on the thermoelectric properties of molecular junctions. Nano Lett. 18, 5666–5672 (2018).
Lee, W. et al. Heat dissipation in atomic-scale junctions. Nature 498, 209–212 (2013).
Ward, D. R., Corley, D. A., Tour, J. M. & Natelson, D. Vibrational and electronic heating in nanoscale junctions. Nat. Nanotechnol. 6, 33–38 (2011).
Lumbroso, O. S., Simine, L., Nitzan, A., Segal, D. & Tal, O. Electronic noise due to temperature differences in atomic-scale junctions. Nature 562, 240–244 (2018).
Cui, L. et al. Quantized thermal transport in single-atom junctions. Science 355, 1192–1195 (2017).
Segal, D., Nitzan, A. & Hänggi, P. Thermal conductance through molecular wires. J. Chem. Phys. 119, 6840–6855 (2003).
Sadeghi, H., Sangtarash, S. & Lambert, C. J. Oligoyne molecular junctions for efficient room temperature thermoelectric power generation. Nano Lett. 15, 7467–7472 (2015).
Klöckner, J. C., Bürkle, M., Cuevas, J. C. & Pauly, F. Length dependence of the thermal conductance of alkane-based single-molecule junctions: an ab initio study. Phys. Rev. B 94, 205425 (2016).
Henry, A. & Chen, G. High thermal conductivity of single polyethylene chains using molecular dynamics simulations. Phys. Rev. Lett. 101, 235502 (2008).
Aradhya, S. V. & Venkataraman, L. Single-molecule junctions beyond electronic transport. Nat. Nanotechnol. 8, 399–410 (2013).
Shen, S., Henry, A., Tong, J., Zheng, R. T. & Chen, G. Polyethylene nanofibres with very high thermal conductivities. Nat. Nanotechnol. 5, 251–255 (2010).
Dubi, Y. & Di Ventra, M. Heat flow and thermoelectricity in atomic and molecular junctions. Rev. Mod. Phys. 83, 131–155 (2011).
Xiang, D., Wang, X., Jia, C., Lee, T. & Guo, X. Molecular-scale electronics: from concept to function. Chem. Rev. 116, 4318–4440 (2016).
Rincón-García, L., Evangeli, C., Rubio-Bollinger, G. & Agraït, N. Thermopower measurements in molecular junctions. Chem. Soc. Rev. 45, 4285–4306 (2016).
Wang, R. Y., Segalman, R. A. & Majumdar, A. Room temperature thermal conductance of alkanedithiol self-assembled monolayers. Appl. Phys. Lett. 89, 173113 (2006).
Wang, Z. et al. Ultrafast flash thermal conductance of molecular chains. Science 317, 787–790 (2007).
Meier, T. et al. Length-dependent thermal transport along molecular chains. Phys. Rev. Lett. 113, 060801 (2014).
Wang, X., Ho, V., Segalman, R. A. & Cahill, D. G. Thermal conductivity of high-modulus polymer fibers. Macromolecules 46, 4937–4943 (2013).
Majumdar, S., Malen, J. A. & McGaughey, A. J. H. Cooperative molecular behavior enhances the thermal conductance of binary self-assembled monolayer junctions. Nano Lett. 17, 220–227 (2017).
Mosso, N. et al. Heat transport through atomic contacts. Nat. Nanotechnol. 12, 430–433 (2017).
Jang, S. Y., Reddy, P., Majumdar, A. & Segalman, R. A. Interpretation of stochastic events in single molecule conductance measurements. Nano Lett. 6, 2362–2367 (2006).
Klöckner, J. C., Cuevas, J. C. & Pauly, F. Transmission eigenchannels for coherent phonon transport. Phys. Rev. B 97, 155432 (2018).
Pauly, F. et al. Cluster-based density-functional approach to quantum transport through molecular and atomic contacts. New J. Phys. 10, 125019 (2008).
Bürkle, M., Hellmuth, T. J., Pauly, F. & Asai, Y. First-principles calculation of the thermoelectric figure of merit for [2,2]paracyclophane-based single-molecule junctions. Phys. Rev. B 91, 165419 (2015).
Krüger, D., Fuchs, H., Rousseau, R., Marx, D. & Parrinello, M. Pulling monatomic gold wires with single molecules: an ab initio simulation. Phys. Rev. Lett. 89, 186402 (2002).
Cui, L. et al. Study of radiative heat transfer in Ångström- and nanometre-sized gaps. Nat. Commun. 8, 14479 (2017); correction 9, 16225 (2018).
Sadat, S., Meyhofer, E. & Reddy, P. High resolution resistive thermometry for micro/nanoscale measurements. Rev. Sci. Instrum. 83, 084902 (2012).
Malen, J. A. et al. Identifying the length dependence of orbital alignment and contact coupling in molecular heterojunctions. Nano Lett. 9, 1164–1169 (2009).
Wang, J. S., Wang, J. & Lü, J. T. Quantum thermal transport in nanostructures. Eur. Phys. J. B 62, 381–404 (2008).
Li, N. et al. Phononics: manipulating heat flow with electronic analogs and beyond. Rev. Mod. Phys. 84, 1045–1066 (2012).
Deglmann, P., Furche, F. & Ahlrichs, R. An efficient implementation of second analytical derivatives for density functional methods. Chem. Phys. Lett. 362, 511–518 (2002).
Deglmann, P., May, K., Furche, F. & Ahlrichs, R. Nuclear second analytical derivative calculations using auxiliary basis set expansions. Chem. Phys. Lett. 384, 103–107 (2004).
TURBOMOLE version 7.1, http://www.turbomole.com (TURBOMOLE GmbH, Karlsruhe, 2016).
Perdew, J. P., Burke, K. & Ernzerhof, M. Generalized gradient approximation made simple. Phys. Rev. Lett. 77, 3865–3868 (1996).
Perdew, J. P. & Wang, Y. Accurate and simple analytic representation of the electron-gas correlation energy. Phys. Rev. B 45, 13244–13249 (1992).
Weigend, F. Accurate Coulomb-fitting basis sets for H to Rn. Phys. Chem. Chem. Phys. 8, 1057–1065 (2006).
Weigend, F. & Ahlrichs, R. Balanced basis sets of split valence, triple zeta valence and quadruple zeta valence quality for H to Rn: design and assessment of accuracy. Phys. Chem. Chem. Phys. 7, 3297–3305 (2005).
Paulsson, M., Krag, C., Frederiksen, T. & Brandbyge, M. Conductance of alkanedithiol single-molecule junctions: a molecular dynamics study. Nano Lett. 9, 117–121 (2009).
P.R. and E.M. acknowledge funding from the US Office of Naval Research (N00014-16-1-2672, instrumentation), the US Department of Energy (DE-SC0004871, scanning probe microscopy) and the US National Science Foundation (1803983). P.R. and E.M. acknowledge the Lurie Nanofabrication Facility and the Michigan Center for Materials Characterization for facilitating the fabrication and calibration of devices. S.-Y.J. gratefully acknowledges support from a National Research Foundation (NRF) grant funded by the Korean Government (no. 2016R1A5A1012966). J.C.K. and F.P. thank the Collaborative Research Center (SFB) 767 of the German Research Foundation (DFG) for financial support. A large part of the numerical modelling was carried out using the computational resources of the bwHPC programme, namely, the bwUniCluster and the JUSTUS HPC facility.
The authors declare no competing interests.
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Peer review information Nature thanks Victor Manuel Garcia Suarez and the other, anonymous, reviewer(s) for their contribution to the peer review of this work.
Extended data figures and tables
Step 1, ‘T’-shaped cantilever patterning. Step 2, deposition of Pt for the serpentine heater-thermometer, pads and the tip. Step 3, SiNx layer deposition for front side KOH etching. Step 4, probe cantilever release. Step 5, aligning each probe on the first shadow mask using a thin low-temperature crystal bond layer. Step 6, SiNx sputtering on the serpentine Pt heater-thermometer. Step 7, aligning each probe on the second shadow mask. Step 8, Au sputtering on the tip region. Step 9, detaching the scanning probe from the shadow mask and removing the residual crystal bond by ‘piranha’ cleaning.
Extended Data Fig. 2 Characterization of thermal and electrical properties of the scanning thermal probes.
a, Measured electrical resistance of the Pt heater-thermometer as a function of temperature. b, Measured thermal response of the scanning probe as a function of the heating frequency. c, Calibration of the thermal conductance of the probe (input heating power provided to the Pt heater-thermometer plotted against the temperature rise of the probe). The slope of the dashed fitted line corresponds to the thermal conductance of the probe.
Extended Data Fig. 3 Evaluation of mechanical properties and spatial temperature variation of the scanning thermal probes.
a–c, A force of 50 nN was applied either in the normal or the transverse directions of the beams, and the deflection for each case was computed (‘Displacement’, colour key). The stiffness of the probe was calculated to be 14,000 N m−1 (a), 275 N m−1 (b) and 12.5 N m−1 (c), respectively, for the normal and two transverse directions. d, e, Calculated temperature field (colour key at right) of the scanning thermal probe when a 10-µA d.c. current was applied to the embedded serpentine Pt heater-thermometer (d) and a 10-µW heat current was input from the tip (e). The spatial temperature distribution on the island is very uniform (<5% change across locations), supporting the expectation that the distributed Pt heater-thermometer accurately measures the temperature of the suspended region.
Extended Data Fig. 4 Sample electrical and thermal conductance traces for Au–C6–Au molecular junctions.
a, b, Two independent sample recordings. Top and bottom panels show electrical and thermal conductance, respectively. The green- and yellow-shaded regions mark portions of the recordings that capture the rupture of a single-molecule junction to which the time-averaging scheme is applied, while the blue-shaded regions during the earlier portions of the withdrawal cycle represent recordings that contain events involving multi-molecule junctions. A clear last step can be identified in the electrical conductance traces (green-yellow region), indicating the breakdown of a single-molecule junction. As can be seen, there are also additional steps before the last step in the blue-shaded region. The corresponding thermal conductance traces that are shown below each electrical conductance trace do not reveal any thermal conductance steps, owing to the low signal-to-noise ratio. Insets, schematics of single-molecule junctions before and after rupture.
Extended Data Fig. 5 Simulated thermal conductance as a function of electrode displacement for C2, C6 and C10 single-molecule junctions.
The computed thermal conductance data are shown as black dots, coloured regions have the same meaning as in Fig. 4, and snapshots of junction structures are displayed as insets. The initial junction geometries before displacement of the electrodes differ from those used to generate the corresponding plots in Fig. 4, but the procedure employed for stretching the junctions is the same.
Extended Data Fig. 6 Influence of the contact geometry on computed phonon transmission for Au–C10–Au single-molecule junctions.
a, Different junction types that are used to evaluate the effect of contact geometry on the phonon transmission functions. Each terminal sulphur atom in the junction is attached to a single Au tip atom (JT1), to two Au tip atoms (JT2, JT3) or to three Au atoms (JT4). In these geometries, electrodes are oriented along the (111) crystallographic direction (JT1, JT4), the (110) direction (JT2) and the (100) direction (JT3). b, Phonon transmission as a function of energy for the different junction geometries illustrated in a.
a–c, Displacement patterns associated with the mode shapes of the most transmissive eigenchannel i = 1 for C2, C6 and C10, respectively, evaluated at energies of 13.5 meV, 14 meV and 18 meV. d, Phonon transmission associated with each of the three eigenchannels i = 1, 2, 3 for C2, C6 and C10 molecular junctions. A peak in the transmission of eigenchannel i = 1 is found to occur at energies of around 13.5 meV, 14 meV and 18 meV for C2, C6 and C10 junctions, respectively, and is indicated by the green bars. The displacement patterns of transmission eigenchannel i = 1 in a–c have been evaluated at these energies.
About this article
Cite this article
Cui, L., Hur, S., Akbar, Z.A. et al. Thermal conductance of single-molecule junctions. Nature 572, 628–633 (2019). https://doi.org/10.1038/s41586-019-1420-z
Scientific Reports (2021)
Nature Nanotechnology (2021)
Nature Nanotechnology (2021)
Side-group-mediated thermoelectric properties of anthracene single-molecule junction with anchoring groups
Scientific Reports (2021)
Nature Materials (2021)