Abstract
The pursuit of superconductingbased quantum computers has advanced the fabrication of and experimentation with custom lattices of qubits and resonators. Here, we describe a roadmap to use present experimental capabilities to simulate an interacting manybody system of bosons and measure quantities that are exponentially difficult to calculate numerically. We focus on the twodimensional hardcore Bose–Hubbard model implemented as an array of floating transmon qubits. We describe a control scheme for such a lattice that can perform individual qubit readout and show how the scheme enables the preparation of a highly excited manybody state, in contrast with atomic implementations restricted to the ground state or thermal equilibrium. We discuss what observables could be accessed and how they could be used to better understand the properties of manybody systems, including the observation of the transition of eigenstate entanglement entropy scaling from arealaw behavior to volumelaw behavior.
Introduction
Analog quantum simulators have evolved in the last two decades from a theoretical concept to an experimental reality (see e.g., refs ^{1,2,3}). Initial experimental success was predominantly achieved with atomic systems, including neutral gases and trapped ions^{4,5,6,7,8}. More recently, superconducting circuits have emerged as a viable quantum simulation platform^{9,10,11,12,13}. This modality—based on “artificial atoms”—features a high degree of experimental controllability and stability^{14}. The flexibility of the superconducting platform has enabled several successful quantum simulation experiments^{15,16,17,18,19,20}.
Here, we show how to realize the twodimensional (2D) hardcore Bose–Hubbard model (HCB) illustrated in Fig. 1 using an array of transmon qubits^{21}, the current workhorse qubit design in superconducting circuits. The HCB is a strongly interacting system that displays some of the critical properties of interacting quantum systems, including the arealaw to volumelaw transition of the entanglement spectrum that has been extensively studied in manybody systems^{22}. Outside of one dimension (1D), this system has no known analytical solution, and its study has been conducted mostly through numerical methods limited in their scope. The most successful approach has been the use of tensornetwork methods, which focus on finding the ground state energy^{23,24}. An experimental realization of a 2D HCB could offer new and complementary insights about the eigenstates and dynamics of manybody systems. It could also be used to validate the results of tensornetwork methods in large systems, and test their underlying assumptions on the nature of manybody wavefunctions. An experimental realization also offers access to the system’s entire spectrum, allowing one to measure the manybody properties of its excited states.
Previous experiments have realized the HCB in 1D^{15,25}, where the model can be solved by analytical methods^{26,27} and has the dynamics of a free fermion gas. Recent realizations have also explored entanglement propagation in ladders and a 3 × 7 array^{20}. Here, we propose the implementation of the 2D HCB with stateoftheart transmon qubits. We calculate the requirements on qubit uniformity and lifetime, and describe the control systems required to measure the array’s manybody properties. Finally, we propose a technique to generate highly excited states that enable one to more completely explore the system’s spectrum and observe its manybody properties.
Superconducting quantum manybody physics simulator
We consider the implementation of a quantum manybody physics simulator (QMBS) with a superconducting quantum circuit made up of multiple repetitions of small basic circuits implementing qubit and coupling elements. Note that while here and throughout the paper we take each site to be a qubit, i.e., a twolevel system, the discussion here applies equally to systems of spins or particles on a lattice. We describe the system with the Hamiltonian
where summation is over all qubits i and over all coupled pairs 〈i, j〉. The terms \({\hat{H}}_{i}^{{\rm{Q}}}\) and \({\hat{H}}_{i,j}^{{\rm{J}}}\) describe the basic qubit and coupling circuits, respectively. The system in Fig. 1 is one example of the Hamiltonian of Eq. (1), with circles (qubits) representing \({\hat{H}}_{i}^{{\rm{Q}}}\) and diamonds (coupling elements) representing \({\hat{H}}_{i}^{{\rm{J}}}\).
We note that the QMBS can be characterized by four energy scales derived from these Hamiltonians, outlined in Table 1. The qubit frequency ω_{q} and hopping strength J are the typical energy scales of the qubit and coupling, respectively, and the anharmonicity A describes the deviation of the qubits from harmonic level spacing. The frequency mismatch Δω is the scale of nonuniformity across the system, including, e.g., variation introduced during fabrication. We neglect deviations in the coupling strength, and assume that the deviations in the first level spacing are typical of the rest of the spectrum.
The behavior of the QMBS depends on the ratio of J to the other three scales. At J ≪ Δω, exchange of energy between different qubits is suppressed, and the system will behave as a collection of uncoupled circuits. In this case, there is no manybody physics to speak of, and the system decomposes into multiple systems with a single degree of freedom each. Thus J ≳ Δω is required for manybody dynamics to appear in the lattice. The ratios \(J/\leftA\right\) and J/ω_{q} then determine which states are effectively coupled and thereby which theoretical models are accessible^{28}. These features are collected in the form of a phase diagram in Fig. 2 and discussed in further detail below.

Hopping dominant: In the regime at the top right corner of Fig. 2, the dominant energy scale is J, the coupling energy. This describes systems such as quantum rotor models in the paramagnetic phase. We note that generally, for a large number of sites, these have a large density of states, and it may be difficult to prepare the system in a lowtemperature quantum state. In that case, the system can be understood by a semiclassical description, and it is hard to observe uniquely quantum dynamics. Such experiments have been performed for large numbers of Josephson junctions^{29,30}.
We note that this regime can be avoided by choosing a different basis of states to describe the Hamiltonian, i.e., by switching the choice of which circuits describe the qubits \({\hat{H}}_{i}^{{\rm{Q}}}\) and the coupling elements \({\hat{H}}_{i,j}^{{\rm{J}}}\).

Particlelike models: In the central portion of the phase diagram, the hierarchy of scales is
$$\Delta \omega\;\lesssim\;J\ll {\omega }_{{\rm{q}}}.$$(2)Here, the rotating wave approximation is valid, and the coupling elements can move an excitation between sites but will not change the total number of excitations. This regime is equivalent to models of bosonic particles, and we may describe the system with the Bose–Hubbard Hamiltonian,
$${\hat{H}}_{i}^{{\rm{Q}}}={\omega }_{{\rm{q}}}{\hat{n}}_{i}+\frac{1}{2}A{\hat{n}}_{i}\left(\hat{{n}_{i}}1\right),$$(3)$${\hat{H}}_{i,j}^{{\rm{J}}}={J}_{xx}\left(\hat{{a}}_{i}^\dagger {\hat{a}}_{j}+{\hat{a}}_{j}^\dagger {\hat{a}}_{i}\right)+{J}_{zz}{\hat{n}}_{i}{\hat{n}}_{j},$$where \({\hat{a}}_{i}^\dagger\) is the creation operator for site i and \({\hat{n}}_{i}={\hat{a}}_{i}^\dagger {\hat{a}}_{i}\) is its energy level. Here, the anharmonicity plays the role of the onsite interaction strength, while interqubit coupling generates transverse hopping terms (J_{xx}) and longitudinal interaction terms (J_{zz}).
The subregime where \(J\;<\;\leftA\right\ll {\omega }_{q}\)—the working point of the transmon qubit^{21}—is the most experimentally accessible parameter regime and is widely adopted by the superconducting circuit community in a multitude of experiments (see e.g., ref. ^{17}), including recent implementations of 1D Bose–Hubbard lattices^{25,31}. In this manuscript, we focus on this regime.
We note that a subset of the particlelike regime, where Δω ~ J, can be used to simulate disordered systems. This can be achieved either by intentionally varying the qubit frequency across the lattice, or by decreasing the hopping energy at a constant residual disorder.

Spinlike models: At the bottom right corner of Fig. 2, the energy scales are given by
$$\Delta \omega \ll {\omega }_{{\rm{q}}}\lesssim J\ll \leftA\right.$$(4)Here, the anharmonicity dominates the coupling term, ensuring that each unit cell remains within the qubit manifold. However, the coupling elements are strong enough to change the qubit state in a nonexcitationconserving way. The rotating wave approximation then breaks down, and the system is best understood by a spinlike model,
$${\hat{H}}_{i}^{{\rm{Q}}}=\frac{{\omega }_{{\rm{q}}}}{2}{\hat{\sigma }}_{i}^{z},\qquad {\hat{H}}_{i,j}^{{\rm{J}}}=\mathop{\sum }\limits_{\mu ,\nu }{J}_{\mu ,\nu }{\hat{\sigma }}_{i}^{\mu }{\hat{\sigma }}_{j}^{\nu }$$(5)where \({\hat{\sigma }}_{i}^{\mu }\) are the Pauli operators on site i.
This regime, where the coupling strength becomes similar to the transition frequencies of the coupled systems, is known as the ultrastrong or deepstrong coupling regime^{32,33} and it is more challenging to realize experimentally. However, superconducting artificial atoms are more suitable for its realization than natural atoms coupled to an electromagnetic cavity, as their coupling strength to a harmonic oscillator mode is not necessarily limited by the fine structure constant^{34,35}. In general, physical couplings in the deepstrong coupling regime can be achieved with strongly nonlinear qubits and highimpedance circuits^{35}. A promising qubit modality to reach such high couplings is the flux qubit, where \({\omega }_{{\rm{q}}}\ll \leftA\right\), as demonstrated experimentally^{36,37}. The fluxonium qubit^{38}, an extension of the flux qubit, has recently been demonstrated to preserve long coherence times while in the high anharmonicity regime^{39}.
Results
For the remainder of this article, we focus our attention on the regime
This combines the two constraints mentioned in our analysis of the possible working regimes: the system operated with these parameters both conserves the number of excitations and remains within the qubit manifold. This is a bosonic model, where each site can be either empty or occupied by a single particle. The system is then described by the effective Hamiltonian
where \({\hat{\sigma }}_{i}^{z},{\hat{\sigma }}_{i}^{\pm }={\hat{\sigma }}_{i}^{x}\pm i{\hat{\sigma }}_{i}^{y}\) are the Pauli z, raising and lowering operators on site i.
As the Hamiltonian is number preserving, its spectrum decomposes into N + 1 distinct sectors defined by the total excitation number n. Each sector is composed of \(\left( {\begin{array}{*{20}{l}}N\,\\\,n\end{array}}\right)\) levels, defined by their rotatingframe energy ϵ, with bandwidth proportional to J. The eigenstates of Eq. (7) are then given by \(\leftn,\epsilon \right\rangle\) where
where E_{G} is the ground state energy. This spectrum is sketched out in Fig. 3.
The HCB is difficult to solve except in some specific cases. The 1D chain can be solved through fermionization^{26,27}, and the case of n/N ≪ 1 (n/N ≈ 1) can be understood analytically by perturbative corrections to the free particle (free hole) problem^{40}; both regimes exhibit noninteracting behavior that is much simpler than what we describe below. In addition, small systems can be exactly diagonalized, as we do here for a 4 × 4 lattice. Beyond these limits, research into the model has generally used tensornetwork methods and focused on the ground state energy^{23,24}. An experimental realization of a 2D version of Eq. (7) can therefore contribute significantly to our understanding of the eigenstates and dynamics of manybody systems, and also the validity and limits of tensornetwork methods in large systems. Beyond this, as we discuss below, an experimental realization can access the system’s entire spectrum.
Manybody physics in the hardcore Bose–Hubbard model
We consider two particular measures of the system’s manybody spectrum: the correlation length and the behavior of entanglement entropy for each eigenstate. In Fig. 4, we show these quantities exhibit transitions along the spectra within each sector: as we go from the edges of the band to the center, the correlation length grows from finite to infinite, and the entanglement entropy of subsystems evolves from obeying an arealaw dependence on the subsystem’s size to a volumelaw dependence.

Correlation length: The typical scale beyond which different sites are no longer correlated serves as an order parameter for phases with longrange order^{41}. The correlation length is a limiting factor for the applicability of tensornetwork methods, which can be used only when correlations are finite^{42}. Having experimental access to the correlation length therefore provides significant insight into the manybody properties of the system.
For our purpose, we define the correlation length in terms of the correlation function
$${C}_{i,j}^{x}\left(\left\psi \right\rangle \right)\equiv \left\langle \psi \right{\hat{\sigma }}_{i}^{x}{\hat{\sigma }}_{j}^{x}\left\psi \right\rangle \left\langle \psi \right{\hat{\sigma }}_{i}^{x}\left\psi \right\rangle \left\langle \psi \right{\hat{\sigma }}_{j}^{x}\left\psi \right\rangle .$$(10)We then extract the correlation length of a state \(\leftn,\epsilon \right\rangle\) by fitting \({C}_{i,j}^{x}\left(\left\psi \right\rangle \right)\) to the form
$${{C}_{i,j}^{x}(n,\epsilon \rangle)}^{2}\simeq {\mathcal{A}}(n,\epsilon)\exp [\overrightarrow{{r}_{i}}{\overrightarrow{r}}_{j}/\xi (n,\epsilon)],$$(11)over all pairs i, j of nearest neighbors and nextnearest neighbors. Here \(\overrightarrow{{r}_{i}}{\overrightarrow{r}}_{j}={x}_{i}{x}_{j}+{y}_{i}{y}_{j}\) is the Manhattan distance between the sites i, j.
We plot the correlation length ξ as a function of eigenstate energy in Fig. 4a for a 4 × 4 lattice near halffilling, where we expect manybody effects to dominate. As discussed above, we observe it goes from finite and short for states at the edge of the band to effectively infinite for states at its center.

Entanglement entropy: For a state with density matrix \(\hat{\rho }\), the entanglement entropy of some subset X of the lattice is the entropy generated when it is severed from the rest of the system,
$${{\mathcal{S}}}_{X}\left(\hat{\rho }\right)=S\left(\hat{\rho}_{X}\otimes {\hat{\rho }}_{\bar{X}}\right)S\left(\hat{\rho }\right),$$(12)where \(S\left(\hat{\sigma }\right)\) is the entropy of \(\hat{\sigma }\), and \(\hat{\rho}_{X}={\mathrm{Tr}\,}_{\forall i\notin X}\;\hat{\rho }\), \(\hat{\rho}_{\bar{X}}={\mathrm{Tr}\,}_{\forall i\in X}\;\hat{\rho }\) are the reduced density matrices of the subsystem X and the remainder of the lattice, respectively. Note that if the initial density matrix \(\hat{\rho }=\left\psi \right\rangle \left\langle \psi \right\) is a pure state, \(S\left(\hat{\rho }\right)\) vanishes while the entropy of both subsystems must be identical, so that
$${{\mathcal{S}}}_{X}\left(\hat{\rho }\right)=2S\left(\hat{\rho }_{X}\right).$$(13)Throughout this paper, for the purpose of numerical calculations, we use the second Rényi entropy,
$$S\left(\hat{\rho }\right)={\log}\,{\mathrm{Tr}}\,{\hat{\rho }}^{2}.$$(14)The entanglement entropy is a measure of entanglement between different parts of the lattice, and has been an important tool in the study of manybody systems. In particular, there has been significant study of the difference between states where it is proportional to the size of the subsystem X (“volumelaw”) and where it is proportional to the size of its boundary (“arealaw”)^{22}. Volumelaw states are also harder to approximate using tensornetwork methods.
To describe the growth law for an eigenstate \(\leftn,\epsilon \right\rangle\), we extract the parameters s_{V} and s_{A} by fitting the entanglement entropy to the form
$${{\mathcal{S}}}_{X}\left(\leftn,\epsilon \right\rangle \left\langle n,\epsilon \right\right)\simeq {s}_{{\rm{V}}}\left(n,\epsilon \right){V}_{X}+{s}_{{\rm{A}}}\left(n,\epsilon \right){A}_{X},$$(15)over different lattice subsets X. Here V_{X} is the number of sites in X (its “volume”) and A_{X} is the number of coupling terms between sites in X and the rest of the lattice (its “area”). The fit parameters can then be understood as
$${s}_{{\rm{V}}}\quad \,\text{Bulk}\, \text{entanglement}\, \text{entropy}\,\text{per}\,\text{site,}\,$$$${s}_{{\rm{A}}}\quad \,\text{Boundary}\, \text{entanglement}\, \text{entropy}\, \text{per}\, \text{bond.}\,$$Thus, the ratio s_{V}/s_{A} determines whether the entanglement entropy obeys an arealawlike or volumelawlike behavior.
We plot this quantity for a 4 × 4 lattice in Fig. 4b. We see the transition from arealaw behavior for states at the edges of the band to volumelaw behavior at its center. We also see little variation in this behavior between different sectors with similar n/N. This allows us to explore the behavior of the entanglement entropy by preparing coherentlike superposition states across multiple sectors, as described below.
Global measures such as the entanglement entropy are key to understanding manybody properties, but observing them in the lab poses experimental challenges. Naively, the entropy of a state is derived from the density matrix \(\hat{\rho }\) and extracting it requires full state tomography. The challenge here is twofold: first, the number of measurements scales exponentially as 2^{2N} ^{43}; and second, one must have sufficient control to apply any combination of rotations \({\hat{\sigma }}_{i}^{\pm }\) to all sites concurrently.
The situation, however, is not quite so dire. Multiple recent proposals have suggested alternative approaches for measuring nonlocal observables such as ntime correlation functions^{44} and the second Rényi entropy^{45,46,47,48}. These proposals substitute random unitaries for the full set of rotations mentioned above, easing the control requirements. They also require fewer unitaries than does full state tomography, though the number of measurements needed still scales exponentially with system size. We note, though, that even as the total size of the system increases, the scaling coefficients s_{V}, s_{A} can be determined from the entanglement entropy of fixedsize subsystems (e.g., a block of sites of size 3 × 3 and all its subsystems), leaving the required number of measurements constant even if we increase N.
As noted above, the emergence of manybody behavior requires relatively uniform qubit frequency, Δω ≲ J. In Fig. 4c, we quantify the tolerable amount of variation for the metrics discussed here. We do so by calculating the behavior of the entanglement entropy at the center of the band and at its edge at varying disorder strength, averaged over multiple realizations of the lattice. We find that up to Δω ≈ 0.5J, one can observe distinctly different physics in different parts of the spectrum. At larger frequency disorder, the variation between lattice realizations dominates this effect.
Prospects for transmon implementation
The transmon qubit^{21} is a natural building block for the implementation of the HCB with a superconducting circuit. It behaves as a weakly nonlinear oscillator with a fundamental transition frequency in the range of ω_{q}/2π ~ 5 GHz. Each lattice site is represented by a single transmon qubit, with the local site energy corresponding to the qubit transition frequency ω_{q}.
The anharmonicity of the transmon qubit is negative, typically in the range of A/2π ~ −250 MHz or ~5% of its frequency^{21}. The selfKerr nonlinearity of the transmon Hamiltonian maps directly onto the onsite interaction term in the Bose–Hubbard model^{25}. As the hardcore Bose–Hubbard model operates in a regime, where \(J/\leftA\right\ll 1\) (Mott insulator phase), the population of the same lattice site with two or more particles is strongly suppressed due to the presence of the selfKerr term, irrespective of its sign. One may note that for large enough lattices, the kinetic energy may reach the scale of the anharmonicity \(\epsilon \propto NJ \sim \leftA\right\). Generally, this effect can be treated as a perturbative correction to the hardcore approximation, as we expect to see only a small number of sites out of a large occupation ∝ N in the forbidden state.
It is straightforward to connect transmon qubits via capacitive coupling^{25}, leading to the hopping term in the Bose–Hubbard model with nearestneighbor coupling energy J. Typical achievable coupling strengths are tens of megahertz, rendering the qubit–qubit interaction well within the strong coupling regime J > Γ, where Γ denotes the qubit decoherence rate. Contemporary transmon qubits feature reproducible coherence times in the range of 20 to 100 μs^{17}, corresponding to Γ/2π ≲ 10 kHz.
As discussed above, an experimental implementation operating in the regime \(J/\leftA\right\ll 1\) suppresses transitions to the second and higher levels, and implements the HCB. In order to observe manybody physics, we generally require the qubit lifetime to be much longer than the characteristic time scale for information to traverse the system, 1/Γ ≫ L/J, where L is the number of hops to go across the system (its length). With five ordersofmagnitude in separation, \(\leftA\right\;\gtrsim\;1{0}^{5}\Gamma\), this is easily achievable with transmon lattices of 100 qubits or more. Generally the sweet spot in this case is \(\left(J \sim \sqrt{\leftA\right\times \Gamma L}\right)/2\pi \sim 1\ {\rm{MHz}}\).
Qubit coherence in the proposed transmon HCB lattice is expected to be at the level of individual stateoftheart transmon qubits^{17}, limited by a combination of material defects^{49} and parasitic coupling to stray modes in the sample package^{50}. Scaling to a larger number of qubits typically requires a chip and sample package of larger dimensions, with the risk of introducing additional parasitic modes at frequencies at or close to the qubit frequencies and therefore impairing qubit performance. In previous implementations of arrays with 24 and 53 qubits, energy relaxation times averaged at around 10 μs^{18} and 15 μs^{19}.
Fabrication variations translate to variations in transmon transitions which may exceed 200 MHz^{51}, yielding disorder in the emulated model on the order of \(\Delta \omega \sim \leftA\right\). To compensate for such variation, we consider a lattice of frequencytunable transmon qubits. This is achieved by replacing the single Josephson junction of the qubit with a dcSQUID, facilitating a frequency tunability of several GHz. In an experiment, this enables one to tune the individual qubit frequencies mutually on resonance (to within their spectral linewidth^{25}).
Individual frequency control requires N slow (dc) control lines for flux biasing each of N qubits. Such lowfrequency wiring can be straightforwardly routed in dilution refrigerators and connected to the sample package in large numbers, as the necessary connectors are compact and bulky attenuation at multiple temperature stages is not required.
Frequency variation in the lattice is mitigated experimentally by calibrating the (dc) flux crosstalk matrix, containing information about the frequency shift of qubit i responding to a flux bias applied to bias line j (1 ≤ i, j ≤ N). In large lattice implementations, qubits are physically located far away from flux bias lines of other qubits. By taking into account only nearestneighbor and nextnearest neighbor parasitic flux coupling, the resulting flux crosstalk matrix is sparse, reducing the number of matrix elements from \(O\left({N}^{2}\right)\) to \(O\left(N\right)\).
In general, flux crosstalk calibration requires the measurement of sections of all N qubit spectra while consecutively biasing each of the N flux control lines. As the spectra can be measured simultaneously with multiplexed readout, this requires \(O\left(N\right)\) individual measurement scans and therefore scales linearly with lattice size.
In addition, dynamic (ac) flux control allows for rapid frequency tuning of the qubits. By detuning a qubit away from its neighbors, we can effectively decouple it from the lattice. For example, in a square lattice, system dynamics can be entirely frozen out, enabling state preparation and readout, by detuning every other qubit in a checkerboard pattern, where all “white” qubits remain at the original frequency and all “black” qubits are shifted.
This scenario requires N/2 qubits to be equipped with fast flux lines, such that even a large lattice of size 10 × 10 requires only 50 flux control lines. Assuming individual bias lines used, enabling full control on each qubit, the number of required coaxial lines is still moderate compared with recent implementations using 50 and 200 coaxial control lines for a 24qubit and 50qubit chip, respectively^{18,19}.
Implementation with floating transmon qubits
Figure 5a shows a possible circuit implementation of the 2D HCB based on a grid of transmon qubits each consisting of two floating electrodes^{52,53,54,55}, in contrast to recent realizations where one of the electrodes is grounded (e.g., Xmon qubits^{56}). In circuit designs with an increasing number of qubits, circuit elements can be proximal or even overlap when using crossover fabrication techniques^{57}. This may result in unwanted spurious coupling, referred to as crosstalk. Such spurious couplings can exist between signal lines, readout resonators, and qubits. In order to minimize this effect, it is advantageous to confine electric fields by decreasing the mode volume; this however comes at the expense of an increased electric field strength, leading to enhanced surface defect loss^{49,58}. The floating layout is advantageous since it suppresses parasitic couplings in the circuit.
To see this, we compare the parasitic coupling of a resonator mode to a floating and a grounded transmon. We assume a (parasitic) capacitive coupling \({C}_{{\rm{P}}},{C}_{{\rm{P}}}^{\prime}\) between the resonator and the electrodes of the floating transmon (circuit diagram in Fig. 5b), or C_{P} to the electrode of the grounded transmon (Fig. 5c). While the coupling capacitance for the grounded transmon is simply
the effective coupling capacitance between resonator and the floating transmon depends on the parasitic capacitances \({C}_{{\rm{P}}},{C}_{{\rm{P}}}^{\prime}\) as well as the capacitance to the ground C_{G}. Assuming without loss of generality \({C}_{{\rm{P}}}^{\prime} \le {C}_{{\rm{P}}}\), circuit analysis (see the Methods section) yields an effective coupling capacitance
We note \({C}_{{\rm{eff}}}^{({\rm{f}})}\le \frac{1}{2}{C}_{{\rm{eff}}}^{({\rm{g}})}\) generically and \({C}_{{\rm{eff}}}^{({\rm{f}})}\ll {C}_{{\rm{eff}}}^{({\rm{g}})}\) if \({C}_{{\rm{P}}}^{\prime} \approx {C}_{{\rm{P}}}\). This corresponds to an effective confinement of electric fields, which is advantageous in larger and more complex circuits. The relation of the effective coupling capacitances \({C}_{{\rm{eff}}}^{({\rm{f}})}/{C}_{{\rm{eff}}}^{({\rm{g}})}\) is plotted in Fig. 5d for typical parameters \({C}_{{\rm{P}}},{C}_{{\rm{P}}}^{\prime} ,{C}_{{\rm{G}}}\). The argument remains valid if the capacitances of the two transmon electrodes to ground are not identical.
Another potential benefit of the floating transmon design is that it provides a tuning knob for the strength of longrange interactions within the lattice. In particular, the coupling range between nonadjacent qubits can be adjusted by controlling C_{G}/C_{sh} (Braumüller et al., unpublished), the ratio of the qubit shunt capacitance to the capacitance of the two pads to the ground. For the implementation of the HCB Hamiltonian, Eq. (7), nextnearest neighbor couplings must be suppressed, which can be achieved in the limit where C_{G} ≫ C_{sh}, but the use of floating transmons opens the possibility of exploring models with nonlocal interactions in the future.
Another strategy to mitigate unwanted crosstalk is to physically separate circuit elements by introducing a multilayer chip layout (3D integration)^{57}. This approach is particularly beneficial in the implementation of a 2D grid of qubits, as the circuit topology prevents inplane access to interior qubits. In a planar layout, this can be resolved by using airbridges to crossover signal lines^{59}, but these are naturally prone to unwanted crosstalk. The 3D integration approach allows for a separation of coherent elements (qubits) on one layer and signal lines on another layer, with their respective electric fields well separated. Couplings between qubit and control or readout lines are achieved via a flipchip approach and connectivity to the other substrate surface is facilitated by throughsilicon vias (TSV), which are lowloss superconducting trenches etched inside the silicon substrate^{57,60}.
Qubit readout and control
Individual qubit readout and control in devices with only few qubits can be achieved by connecting a separate signal line to each qubit. For a QMBSstyle device with a large number of qubits, this approach is limited by the available number of signal lines as well as by geometric constraints. Instead, efficient multiplexed readout can be performed by coupling multiple qubits to a single signal line through individual dispersive readout resonators with frequencies spaced at intervals large compared to their linewidths^{61,62}. We sketch out an example of this setup in Fig. 5a.
As implied by the color coding in Fig. 5a, signal lines must cross qubit pads or qubit coupling elements in a planar circuit implementation in order to reach qubits inside the lattice, leading to experimental challenges. A possible strategy to address this issue is the use of 3D integration techniques^{57}.
The particulars of dispersive readout for individual qubits are well established. The challenge in reading out a large, degenerate array of qubits is the interplay between measurement and the ongoing dynamics. To get a snapshot of the system at a particular time, we must generally measure the qubits on a time scale T_{meas} ≪ 1/J, or else freeze the dynamics.
For a homodyne measurement, typical measurement time scales as^{63}
where κ is the resonator linewidth, χ its dispersive shift between qubit states g, e; and \(\bar{n}\) is the mean number of photons in the cavity during readout. There are two limiting factors for this readout speed: cavity occupation must remain below the critical photon number in order to ensure to operate in the linear dispersive regime, and the induced Purcell decay of the qubit, γ_{P}, must remain small^{64,65},
Here η_{PF} accounts for protection resulting from a Purcell filter^{65}, and L is the maximum distance between any two qubits. We have taken the anharmonicity \(\leftA\right\) to be much smaller than the qubitresonator detuning. If we keep fixed
then the measurement time is
We find that the operating regime for measurement depends on the ratio \(J/\leftA\right\), favoring a smaller J. The design is limited, however by the factors we have previously discussed. The hopping energy must exceed the frequency disorder across different qubits, J ≳ Δω; with individual (dc) flux bias lines, one can reasonably expect to achieve Δω/2π ≈ 100 kHz, independent of lattice size. The rate must also be fast enough to allow information to travel across the entire system before decoherence kicks in; at a conservative qubit lifetime of T_{1} ≈ 10 μs, this translates into the requirement J/2π ≫ L × 15 kHz. Thus, a larger 10 × 10 lattice, with L = 20, requires J/2π ≳ 3 MHz, \(J/\leftA\right\;\gtrsim\;0.01\).
We find that one of several experimental approaches can be taken:

If \(J\;\lesssim\;0.03\sqrt{{\varepsilon }_{1}{\varepsilon }_{2}/{\eta }_{{\rm{PF}}}L}\leftA\right\), we can choose system parameters, and in particular κ > J, such that JT_{meas} ≲ π/10. In this case, we can easily readout the state of the system faster than it evolves. Taking a typical ε_{1} = ε_{2} = 0.2, this regime can be reached by using narrow Purcell filters, η_{PF} ≤ 0.01, and large bandwidth cavities, κ/2π ≳ 20MHz. Multiplexed nondemolition qubit readout with similar parameters was demonstrated in less than T_{meas} = 50 ns^{65}.
The experimental overhead for this approach is large in bigger lattices. As the Purcell filters must be spectrally very narrow, only one cavity can be brought in direct resonance with each filter, and so each qubit needs a readout resonator and a separate Purcell filter. Cavity frequencies must be spaced sufficiently far apart, at intervals of Δ ≳ 100 MHz. Another downside to this approach is that narrow filters, while increasing the qubit lifetime, make it hard to drive the qubits through the readout line. As we discuss below, we find that this is a useful tool in preparing states that explore the system’s manybody properties, and if the readout cannot be used in this way separate drive lines would be necessary.

If \(0.03\sqrt{{\varepsilon }_{1}{\varepsilon }_{2}/L}\leftA\right\;\lesssim\;J\ll {\varepsilon }_{1}\leftA\right\), measurement speed is limited. However, if the Stark shift generated by driving the cavity detunes the measured qubit away from the lattice, \(\delta {\omega }_{{\rm{q}}} \sim \bar{n}\chi \sim {\varepsilon }_{1}\leftA\right\gg J\), its state is frozen and we can once again readout a snapshot at a given time.
A design of this form would call for \(\left(\chi \approx \kappa \right)/2\pi \approx 5\ {\rm{MHz}}\). If neighboring qubits are to be measured simultaneously, the driving pulses must be carefully calibrated to maintain a frequency detuning, which means the protocol may not be robust.

Finally, if \(J\;\gtrsim\;{\varepsilon }_{1}\leftA\right\), we necessarily have T_{meas} ≳ 1/J. This is the weak continuous measurement regime^{66}, and the amount of information that can be extracted about the system is reduced: we would not, for example, be able to obtain the probability statistics required to measure the entropy of a state. In this regime, full readout can be enabled by turning off interactions, either directly^{67}, or by making use of frequencytunable qubits.
We can effectively freeze out the interactions between the qubits by mutually detuning their frequencies, essentially shifting the system into the individual particle regime. Note that we do not need an infinite array of frequencies, as only coupled qubits must be detuned from each other. In a square lattice, qubits can be detuned in a checkerboard pattern, as described above. This freeze out can be achieved by attaching fast flux lines to N/2 qubits, requiring comparable or reduced overhead to the use of individual Purcell filters, similar to previously realized setups^{18,19}. This method also allows for more flexibility in measuring observables other than \({\hat{\sigma }}^{z}\), as rotation pulses can be applied to the qubit between detuning and measurement, possibly through the cavity array, as described below.
Although the resonator configuration discussed above enables selective readout of specific or all qubits, it does not facilitate individual qubit control with microwave drives when all the qubits in the lattice are degenerate.
This issue can be overcome in several ways. Most directly, it may be useful to couple control lines to a single or few specific qubits to allow for direct microwave control, e.g., to prepare a certain initial state in the lattice. Alternately, the use of tunable qubits—which we have suggested above for the purpose of a freezeout prior to qubit readout—allows one to address an individual qubit or a subset of qubits if they are detuned in frequency away from the otherwise degenerate lattice.
In addition, the readout layout described above can be used to effect a specific form of systemwide driving. We note, when a signal line ℓ is driven at near resonance, at ω_{d} ≈ ω_{q}, the effective Hamiltonian becomes
where the driving operator is given by
Here, the summation is over the set of qubits \({{\mathbb{S}}}_{\ell }\) coupled to the signal line ℓ (Fig. 5a), \({\tilde{\alpha }}_{i}\) is the effective relative coupling to that qubit, determined by the resonator’s parameters, and \(\tilde{g}\) is a coupling energy proportional to the driving strength. See the Methods section for the derivation of this operator and the values of \(\tilde{g},{\tilde{\alpha }}_{i}\).
Although the set of operators \({\hat{\Sigma }}_{\ell }\) does not allow us full control of the system, driving at different strengths or for different lengths of time allows us access to a set of defined unitary transformations. As mentioned above, this would allow the measurement of quantities such as the entropy of a subsystem^{45,46}. As we discuss below, it also enables the preparation of manybody states whose nature is determined by the detuning of the drive from the qubit frequency and can be used to probe the spectrum of the system.
Coherentlike states
As we have seen, the most interesting behavior of the HCB is manifest in the finiteexcitation density sectors where 0 < n/N < 1. Within these sectors, energy eigenmodes vary in their behavior between the edges of the band and its center, exhibiting manybody properties such as different entanglement entropy laws. To study these properties, we must be able to prepare such states, which is challenging. In our proposed implementation, state preparation can be performed by applying drive pulses that reach the qubits via the readout resonators. To prepare a specific eigenstate, we would not only have to tailor a series of specific pulses, but also know the wavefunction of the prepared state, negating the premise of a quantum simulator to access states which are not understood theoretically.
Here, we propose an alternate route to observing the spectral properties of the HCB. Instead of preparing a specific known eigenstate, we apply a weak drive using the operators of Eq. (23) at some detuning from the joint qubit frequency. This prepares the lattice in a coherent statelike superposition of eigenstates in multiple n sectors, but with definite kinetic energy within each sector. This strategy of extracting manybody properties is robust with regards to experimental control limitations on chip.
To understand this process, we begin by rewriting the Hamiltonian of Eq. (7) in its eigenmode basis,
where \(\leftn,\epsilon \right\rangle\) are the eigenstates of Eq. (8) and \({\rho }_{\epsilon }^{n}\) is the density of states for the sector with n excitations. Then, we rewrite the driving operator of Eq. (23) in the same basis,
Consider first the perturbative limit, where the driving is very weak compared with the energy spacing,
In this case, the driving operator will couple only eigenstates differing exactly by the detuning,
and we can approximate it as a combination of definedenergy raising operators
where ϵ_{n} = ϵ + n × δ. Observe that each \({\hat{A}}_{\varepsilon }\) couples a subset of eigenstates of the form \(\leftn,\epsilon +n\times \delta \right\rangle\). In the spectrum outlined in Fig. 3, these can be identified as the states sitting on a line with slope δ and intersecting n = 0 at ϵ.
Thus, if we initialize the system in the ground state,
it is affected only by \({\hat{A}}_{0},{\hat{A}}_{0}^\dagger\). Inserting the operators of Eq. (28) into the Hamiltonian of Eq. (22), we find at later times it has a form reminiscent of a coherent state,
While this wavefunction is difficult to evaluate theoretically, it is composed only of states of a defined energy, \(\leftn,n\times \delta \right\rangle\), i.e.,
for some timedependent functions \({c}_{n}\left(t\right)\). As described above, these eigenstates lie along a line with slope δ in the spectrum shown in Fig. 3. This form can be observed in Fig. 6a for a numerical simulation of a system with very weak driving.
In practice, the approximation of Eqs. (26) and (28) are insufficient to describe the dynamics. For any fixed n/N, the energy spacing between states shrinks exponentially with N as we increase the size of the lattice, violating the assumption of Eq. (26). For weak driving, the qualitative picture remains similar but the prepared state seen in Eq. (31) acquires a finite width in energy space, proportional to the driving strength. These features are seen in Fig. 6.
We have discussed above how to prepare the HCB system in a coherentlike state. This state has a defined kinetic energy per excitation, but it does not have a definite excitation number. We argue that this is not an impediment to measuring the manybody properties described above.
First, we note that for any measurements purely in the \({\hat{\sigma }}^{z}\) basis we can effectively project the state into a definite n sector by postselection.
Second, we have observed in Fig. 4b that the manybody properties that we are interested in behave similarly in different n sectors of the spectrum. For these, we expect the state in Eq. (31) to exhibit the same behavior as a function of its kinetic energy.
As such, preparing these coherentlike states may allow us to measure manybody properties of the spectrum by varying the detuning δ. We verify this numerically in Fig. 7, where we described a state prepared this way and measure its manybody properties. We find that the correlation length of the state, shown in Fig. 4a, approximates very well the eigenmode correlation length for states in similar energy show in Fig. 7b. Similarly, the entanglement entropy measured as shown in Fig. 7c exhibits the same behaviors we pointed out in Fig. 4b.
Discussion
We have offered here a roadmap for the realization of a quantum manybody simulator of the 2D hardcore Bose–Hubbard model using a superconducting circuit made up of transmon qubits. An experimental realization of this setup would allow the exploration of this analytically hardtosolve model in regimes where it has not been realized before. In particular, we have shown how such a realization could access nonequilibrium states that exhibit manybody wavefunction behaviors such as a crossover from volumelaw to arealaw entanglement. As discussed throughout, the experimental parameters we consider in this article are within reach of current fabrication and control systems. The system we have proposed could be realized in the near term.
In the body of this paper, we have presented numerical results for a 4 × 4 HCB lattice, which can be diagonalized on a moderately powerful computer. However, the difficulty of this task grows exponentially, and a system of 6 × 6 or 7 × 7 sites is beyond numerical reach for any reasonable resource expenditure. An experimental realization would thus provide an example of quantum simulation beyond our theoretical and numerical abilities.
Beyond the model presented here, the paradigm of the QMBS can be used to explore a variety of other systems. Two immediate extensions of the model include changing the lattice topology or varying individual qubit frequencies to understand the role of disorder in this manybody system. In the longer term, it would be interesting to explore other parts of the phase diagram in Fig. 2. In particular, a reliable and longlived qubit with large anharmonicity would allow us to realize spin systems and explore their rich physics, including probing phase transitions and understanding spin liquids.
Methods
Driving through a line coupled to multiple qubits
Here, we give the derivation for the driving operator of Eq. (23).
The system used, schematically shown in Fig. 5a, is described by the Hamiltonian
where \({\hat{H}}_{{\rm{HCB}}}\), given in Eq. (7), describes the qubits, \({\hat{H}}_{\ell }^{{\rm{L}}}\) the signal line ℓ,
and \({\hat{H}}_{i}^{\ell }\) the resonator coupling line ℓ to qubit i,
Here, ℓ sums over the different signal lines; for each line, \({\hat{R}}_{\nu }^{\ell }\) (\({\hat{L}}_{\nu }^{\ell }\)) are the annihilation operators for its right (left) moving modes with energy ν, and \({{\mathbb{S}}}_{\ell }\) is the set of qubits coupled to it through resonators. For each resonator coupled to qubit i, \({\hat{c}}_{i}\) is the annihilation operator for a photon in the resonator, and Δ_{i}, g_{i}, κ_{i}, τ_{i} are that resonator’s detuning, its coupling to the qubit i, its linewidth, and its distance from the termination of the signal line (divided by the speed of light), respectively. This setup is outlined in Fig. 5(a).
Using standard input–output theory^{68}, the Heisenberg–Langevin equations of motion for the operators \({\hat{c}}_{i}\) are
where \({\hat{\xi }}_{\ell }^{{\rm{L}}},{\hat{\xi }}_{\ell }^{{\rm{R}}}\) are Gaussian white noise operators describing the vacuum fluctuations of the leftmoving and rightmoving modes, respectively, on the line ℓ coupled to i.
If we drive the line at frequency ω_{d}, we have
where Ω is the driving field. We find, in steady state,
In a dispersive readout scheme the linewidths of the cavities are narrow^{61},
If we then drive near the qubit frequency,
we can approximate
Now, from Eqs. (32) and (34), we have that the driving Hamiltonian can be described by
and for ω_{d} ~ ω_{q}, we can take the rotating wave approximation and combined with Eq. (40) we find
where
as in Eq. (23), and
Circuit analysis of the floating transmon qubit
We review the Hamiltonian of a floating transmon qubit coupled to a harmonic oscillator mode, depicted in Fig. 8a. This allows us to extract effective values for the qubit capacitance C_{q} and the coupling capacitance C_{c} comparable to those of a grounded transmon qubit, shown in Fig. 8b. In the Results section, we utilize this result to compare unwanted crosstalk in an architecture with floating transmon qubits versus an architecture that makes use of grounded transmons.
Following the node flux representation described in ref. ^{69} we can write down the Lagrangian for the circuit in Fig. 8a as
where Φ_{i} are node fluxes and ϕ_{i} = 2πΦ_{i}/Φ_{0} node phases, with Φ_{0} the magnetic flux quantum. E_{J} = Φ_{0}I_{c}/2π is the Josephson energy of the Josephson junction with critical current I_{c}. The kinetic part of the Lagrangian can also be written as
where \(\overrightarrow{\Phi }={({\Phi }_{1}\,\,{\Phi }_{2}\,\,{\Phi }_{3})}^{{\rm{T}}}\) and \(\check{C}\) the capacitance matrix defined by Eq. (48).
In order to recover the relevant transmon degree of freedom, we perform a variable transformation in the transmon subspace to ‘plusminus’ variables Φ_{±} = Φ_{1} ± Φ_{2}. With the transformation matrix
we can rewrite the capacitive part of the Lagrangian as
Here \(\overrightarrow{\Phi }^{\prime} =S\cdot \overrightarrow{\Phi }={({\Phi }_{+}\,\,{\Phi }_{}\,\,{\Phi }_{3})}^{\rm T}\), and the capacitance matrix in the transformed basis becomes \(\check{{\mathcal{C}}}={S}^{1}\check{C}{S}^{1}\).
A Legendre transformation yields the circuit Hamiltonian
where \(\overrightarrow{q}^{\prime} =({q}_{+}\,\,{q}_{}\,\,{q}_{3})^{\rm T}\). Since the ‘+’mode of the transmon does not have an inductive term in the Hamiltonian, its frequency is not relevant for qubit operation. Conversely, the Josephson energy of the transmon enters via the ‘−’mode. We can therefore trace over the q_{+} degree of freedom, to find
where
is the matrix \({\check{{\mathcal{C}}}}^{1}\) with the column and row corresponding to the + mode removed.
The effective Hamiltonian of Eq. (53) has the same form as the Hamiltonian resulting from analysis of the circuit Fig. 8b, with the substitutions Φ_{1} → Φ_{−}, q_{1} → q_{+}. We can then find the effective parameters of the reduced circuit by identifying
We therefore find the effective transmon capacitance, including coupling capacitances to the resonator, from the diagonal entry,
and from the offdiagonal entries we can extract the effective coupling capacitance between the floating transmon qubit and the resonator
Applied to the circuit in Fig. 5b, we find the parasitic coupling between the floating transmon qubit and the resonator
taking C_{g1} = C_{g2} = C_{G}.
Data availability
The results of the simulations generated during the study are available from the corresponding author on reasonable request and with the approval of our US Government sponsor.
Code availability
The simulation code generated during the study is available from the corresponding author on reasonable request and with the approval of our US Government sponsor.
References
Buluta, I. & Nori, F. Quantum simulators. 326, 108–111 (2009).
Cirac, J. I. & Zoller, P. Goals and opportunities in quantum simulation. Nat. Phys. 8, 264–266 (2012).
Georgescu, I. M., Ashhab, S. & Nori, F. Quantum simulation. Rev. Mod. Phys. 86, 153 (2014).
Greiner, M., Mandel, O., Esslinger, T., Hansch, T. W. & Bloch, I. Quantum phase transition from a superfluid to a Mott insulator in a gas of ultracold atoms. Nature 415, 39–44 (2002).
Friedenauer, A., Schmitz, H., Glueckert, J. T., Porras, D. & Schaetz, T. Simulating a quantum magnet with trapped ions. Nat. Phys. 4, 757–761 (2008).
Gerritsma, R. et al. Quantum simulation of the dirac equation. Nature 463, 68–71 (2010).
Schneider, U. et al. Fermionic transport and outofequilibrium dynamics in a homogeneous hubbard model with ultracold atoms. Nat. Phys. 8, 213–218 (2012).
Greif, D., Uehlinger, T., Jotzu, G., Tarruell, L. & Esslinger, T. Shortrange quantum magnetism of ultracold fermions in an optical lattice. Science 340, 1307–1310 (2013).
Houck, A. A., Türeci, H. E. & Koch, J. Onchip quantum simulation with superconducting circuits. Nat. Phys. 8, 292–299 (2012).
Marcos, D., Rabl, P., Rico, E. & Zoller, P. Superconducting circuits for quantum simulation of dynamical gauge fields. Phys. Rev. Lett. 111, 110504 (2013).
Schmidt, S. & Koch, J. Circuit QED lattices: towards quantum simulation with superconducting circuits. Ann. Phys. 525, 395–412 (2013).
Devoret, M. H. & Schoelkopf, R. J. Superconducting circuits for quantum information: an outlook. Science 339, 1169–1174 (2013).
Neill, C. et al. A blueprint for demonstrating quantum supremacy with superconducting qubits. Science 360, 195–199 (2018).
Krantz, P. et al. A quantum engineeras guide to superconducting qubits. Appl. Phys. Rev. 6, 021318 (2019).
Roushan, P. et al. Spectroscopic signatures of localization with interacting photons in superconducting qubits. Science 358, 1175–1179 (2017).
Lamata, L., ParraRodriguez, A., Sanz, M. & Solano, E. Digitalanalog quantum simulations with superconducting circuits. Adv. Phys. X 3, 1457981 (2018).
Kjaergaard, M. et al. Superconducting qubits: current state of play.Annual Condensed Mat. Phys. 11, 369–395 (2020).
Ye, Y. et al. Propagation and localization of collective excitations on a 24qubit superconducting processor. Phys. Rev. Lett. 123, 050502 (2019).
Arute, F. et al. Quantum supremacy using a programmable superconducting processor. Nature 574, 505–510 (2019).
Chiaro, B. et al. Growth and preservation of entanglement in a manybody localized system. Preprint at http://arxiv.org/abs/1910.06024 (2019).
Koch, J. et al. Chargeinsensitive qubit design derived from the Cooper pair box. Phys. Rev. A 76, 042319 (2007).
Eisert, J., Cramer, M. & Plenio, M. B. Colloquium: area laws for the entanglement entropy. Rev. Mod. Phys. 82, 277–306 (2010).
Murg, V., Verstraete, F. & Cirac, J. I. Variational study of hardcore bosons in a twodimensional optical lattice using projected entangled pair states. Phys. Rev. A 75, 033605 (2007).
Jordan, J., Orús, R. & Vidal, G. Numerical study of the hardcore Bose–Hubbard model on an infinite square lattice. Phys. Rev. B 79, 174515 (2009).
Ma, R. et al. A dissipatively stabilized Mott insulator of photons. Nature 566, 51 (2019).
Paredes, B. et al. Tonks–Girardeau gas of ultracold atoms in an optical lattice. Nature 429, 277 (2004).
Girardeau, M. Relationship between systems of impenetrable Bosons and Fermions in one dimension. J. Math. Phys. 1, 516–523 (1960).
Sachdev, S. Quantum Phase Transitions (Cambridge University Press, Cambridge, UK, 2011).
van der Zant, H. S. J., Elion, W. J., Geerligs, L. J. & Mooij, J. E. Quantum phase transitions in two dimensions: experiments in Josephsonjunction arrays. Phys. Rev. B 54, 10081–10093 (1996).
Paramanandam, J., Bell, M. T., Ioffe, L. B. & Gershenson, M. E. Magnetic field driven quantum phase transitions in Josephson arrays. Preprint at http://arxiv.org/abs/1112.6377 (2011).
Yan, Z. et al. Strongly correlated quantum walks with a 12qubit superconducting processor. Science 364, 753–756 (2019).
Casanova, J., Romero, G., Lizuain, I., GarcíaRipoll, J. J. & Solano, E. Deep strong coupling regime of the jaynescummings model. Phys. Rev. Lett. 105, 263603 (2010).
FornDíaz, P., Lamata, L., Rico, E., Kono, J. & Solano, E. Ultrastrong coupling regimes of lightmatter interaction. Rev. Mod. Phys. 91, 025005 (2019).
Devoret, M., Girvin, S. & Schoelkopf, R. Circuitqed: how strong can the coupling between a josephson junction atom and a transmission line resonator be? Ann. Phys. 16, 767–779 (2007).
Manucharyan, V. E., Baksic, A. & Ciuti, C. Resilience of the quantum rabi model in circuit QED. J. Phys. A Math. Theor. 50, 294001 (2017).
Yoshihara, F. et al. Superconducting qubitoscillator circuit beyond the ultrastrongcoupling regime. Nat. Phys. 13, 44–47 (2017).
FornDíaz, P. et al. Ultrastrong coupling of a single artificial atom to an electromagnetic continuum in the nonperturbative regime. Nat. Phys. 13, 39–43 (2017).
Manucharyan, V. E., Koch, J., Glazman, L. I. & Devoret, M. H. Fluxonium: single cooperpair circuit free of charge offsets. Science 326, 113–116 (2009).
Nguyen, L. B. et al. High coherence fluxonium qubit. Phys. Rev. X 9, 041041 (2019).
Schick, M. Twodimensional system of hardcore Bosons. Phys. Rev. A 3, 1067–1073 (1971).
Altland, A. & Simons, B. Condensed Matter Field Theory, 2nd edn. (Cambridge University Press, Cambridge, UK, 2010).
Orús, R. A practical introduction to tensor networks: Matrix product states and projected entangled pair states. Ann. Phys. 349, 117–158 (2014).
Haah, J., Harrow, A. W., Ji, Z., Wu, X. & Yu, N. Sampleoptimal tomography of quantum states. IEEE Trans. Inf. Theory 63, 5628–5641 (2017).
Pedernales, J. S., DiCandia, R., Egusquiza, I. L., Casanova, J. & Solano, E. Efficient quantum algorithm for computing ntime correlation functions. Phys. Rev. Lett. 113, 020505 (2014).
van Enk, S. J. & Beenakker, C. W. J. Measuring \(\mathrm{Tr}\,{\rho }^{n}\) on single copies of ρ using random measurements. Phys. Rev. Lett. 108, 110503 (2012).
Elben, A., Vermersch, B., Roos, C. F. & Zoller, P. Statistical correlations between locally randomized measurements: a toolbox for probing entanglement in manybody quantum states. Phys. Rev. A 99, 052323 (2019).
Elben, A., Vermersch, B., Dalmonte, M., Cirac, J. I. & Zoller, P. Rényi entropies from random quenches in atomic Hubbard and spin models. Phys. Rev. Lett. 120, 050406 (2018).
Vermersch, B., Elben, A., Sieberer, L. M., Yao, N. Y. & Zoller, P. Probing scrambling using statistical correlations between randomized measurements. Phys. Rev. X 9, 021061 (2019).
Oliver, W. D. & Welander, P. B. Materials in superconducting quantum bits. MRS Bull. 38, 816–825 (2013).
Lienhard, B. et al. In Proc. 2019 IEEE/MTTS International Microwave Symposium 275–278 (Boston, MA, USA, 2019).
Gambetta, J. M., Chow, J. M. & Steffen, M. Building logical qubits in a superconducting quantum computing system. npj Quantum Inf. 3, 2 (2017).
Chang, J. B. et al. Improved superconducting qubit coherence using titanium nitride. Appl. Phys. Lett. 103, 012602 (2013).
Córcoles, A. D. et al. Demonstration of a quantum error detection code using a square lattice of four superconducting qubits. Nat. Commun. 6, 6979 (2015).
Braumüller, J. et al. Concentric transmon qubit featuring fast tunability and an anisotropic magnetic dipole moment. Appl. Phys. Lett. 108, 032601 (2016).
Reagor, M. et al. Demonstration of universal parametric entangling gates on a multiqubit lattice. Sci. Adv. 4, eaao3603 (2018).
Barends, R. et al. Coherent Josephson qubit suitable for scalable quantum integrated circuits. Phys. Rev. Lett. 111, 080502 (2013).
Rosenberg, D. et al. 3D integrated superconducting qubits. npj Quantum Inf. 3, 42 (2017).
Martinis, J. M. et al. Decoherence in Josephson qubits from dielectric loss. Phys. Rev. Lett. 95, 210503 (2005).
Chen, D., Meldgin, C. & DeMarco, B. Bathinduced band decay of a Hubbard lattice gas. Phys. Rev. A 90, 013602–013602 (2014).
Yost, D.R. W. et al. Solidstate qubits integrated with superconducting throughsilicon vias. Preprint at http://arxiv.org/abs/1912.10942 (2019).
Blais, A., Huang, R.S., Wallraff, A., Girvin, S. M. & Schoelkopf, R. J. Cavity quantum electrodynamics for superconducting electrical circuits: an architecture for quantum computation. Phys. Rev. A 69, 062320 (2004).
Heinsoo, J. et al. Rapid highfidelity multiplexed readout of superconducting qubits. Phys. Rev. Appl. 10, 034040 (2018).
Gambetta, J. et al. Quantum trajectory approach to circuit QED: quantum jumps and the Zeno effect. Phys. Rev. A 77, 012112–012112 (2008).
Houck, A. A. et al. Controlling the spontaneous emission of a superconducting transmon qubit. Phys. Rev. Lett. 101, 080502 (2008).
Walter, T. et al. Rapid highfidelity singleshot dispersive readout of superconducting qubits. Phys. Rev. Appl. 7, 054020 (2017).
Clerk, A. A., Devoret, M. H., Girvin, S. M., Marquardt, F. & Schoelkopf, R. J. Introduction to quantum noise, measurement, and amplification. Rev. Mod. Phys. 82, 1155–1208 (2010).
Yan, F. et al. Tunable coupling scheme for implementing highfidelity twoqubit gates. Phys. Rev. Appl. 10, 054062 (2018).
Gardiner, C. W. & Zoller, P. Quantum Noise (Springer, Berlin/Heidelberg, 2004).
Vool, U. & Devoret, M. Introduction to quantum electromagnetic circuits. Int. J. Circuit Theory Appl. 45, 897–934 (2017).
Acknowledgements
This research was funded in part by the National Science Foundation under grants PHY1720311 and 1839197; and by the Department of Defense via MIT Lincoln Laboratory under U.S. Air Force Contract No. FA872105C0002. The views and conclusions contained herein are those of the authors and should not be interpreted as necessarily representing the official policies or endorsements of the U.S. Government.
Author information
Authors and Affiliations
Contributions
Y.Y., C.T. and W.D.O. devised to the initial concept. Y.Y. performed the analysis and numerical simulations of the HCB and coherentlike state preparation. J.B. performed the analysis related to the floating transmon implementation. Y.Y. and J.B. wrote the paper, and all the authors contributed to the discussions.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Yanay, Y., Braumüller, J., Gustavsson, S. et al. Twodimensional hardcore Bose–Hubbard model with superconducting qubits. npj Quantum Inf 6, 58 (2020). https://doi.org/10.1038/s4153402002691
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s4153402002691
This article is cited by

Probing quantum information propagation with outoftimeordered correlators
Nature Physics (2022)

Engineered dissipation for quantum information science
Nature Reviews Physics (2022)

Quantum transport and localization in 1d and 2d tightbinding lattices
npj Quantum Information (2022)

Unimon qubit
Nature Communications (2022)