Abstract
The broad employment of water electrolysis for hydrogen (H2) production is restricted by its large voltage requirement and low energy conversion efficiency because of the sluggish oxygen evolution reaction (OER). Herein, we report a strategy to replace OER with a thermodynamically more favorable reaction, the partial oxidation of formaldehyde to formate under alkaline conditions, using a Cu3Ag7 electrocatalyst. Such a strategy not only produces more valuable anodic product than O2 but also releases H2 at the anode with a small voltage input. Density functional theory studies indicate the H2C(OH)O intermediate from formaldehyde hydration can be better stabilized on Cu3Ag7 than on Cu or Ag, leading to a lower C-H cleavage barrier. A two-electrode electrolyzer employing an electrocatalyst of Cu3Ag7(+)||Ni3N/Ni(–) can produce H2 at both anode and cathode simultaneously with an apparent 200% Faradaic efficiency, reaching a current density of 500 mA/cm2 with a cell voltage of only 0.60 V.
Similar content being viewed by others
Introduction
Hydrogen (H2) is not only an important feedstock in the chemical industry (e.g., petroleum refining, ammonia production from the Haber–Bosch process) but also plays an important role in the future energy economy because H2 is a carbon-zero energy carrier and can be directly utilized as a fuel in hydrogen fuel cells1,2,3. Even though mature industry processes exist for the production of H2, such as steam methane reforming, their strong dependence on unsustainable fossil resources and large CO2 emission call on greener alternative methods for producing H24. Against this backdrop, electrocatalytic water splitting, which consists of the H2 and O2 evolution reactions (HER and OER), has attracted worldwide attention these years5. Despite the great efforts devoted to developing competent electrocatalysts for both half-reactions and ingenious designs of electrolyzers, the thermodynamics of water splitting dictates its large cell voltage input >1.23 V (Fig. 1a) and hence high-energy consumption (>4.5–6 kWh/m3 H2)6,7,8,9. In fact, the more energy-demanding OER produces O2 as a low-value product at the anode while H2 is only produced at the cathode. Therefore, there is an increasing interest in exploring alternative oxidation reactions to replace OER with lower energy input10. Even more desirable is that value-added products instead of O2 could be simultaneously obtained at the anode.
Indeed, electrocatalytic oxidation of a variety of inorganic and organic feedstocks has been explored to integrate with HER to produce H2 with lower voltage input11,12. For instance, our group has reported several electrocatalytic systems to couple the oxidative valorization of various biomass-derived intermediates (e.g., 5-hydroxymethylfurfural (HMF), furfural, etc.) with HER in aqueous media13,14,15,16,17. Other small molecules, such as urea18,19, ammonia20, and hydrazine21, have also been reported to replace OER for more energy-efficient H2 production from water, which produces CO2 and/or N2 at the anode. Despite the great progress in this direction, H2 is only produced at the cathode and most electrocatalytic systems still require a cell voltage larger than 1 V to reach an industrially relevant current density (>500 mA/cm2). Furthermore, the utilization of biomass-derived feedstocks such as HMF and furfural for the large-scale production of H2 is still questionable because of the tremendous disparity in their scalability and the future H2 demand. Consequently, it remains a great challenge to develop an alternative strategy to produce H2 from water with ultra-low voltage input, and even more desirable is to produce H2 at both cathode and anode.
We were inspired by the advance in H2 generation from liquid-phase hydrogen storage molecules, such as NaBH422, NH3BH323,24, and HCOOH25,26, which are able to release H2 under thermocatalytic conditions. Among those liquid organic hydrogen storage molecules, formaldehyde (HCHO) is particularly appealing, because the partial HCHO oxidation (FOR) to formate is also able to release H2 at the anode with a very small thermodynamic potential (HCHO+2OH− → HCOO−+1/2H2+H2O+e−, E = –0.22 V vs. RHE, Fig. 1b)27. Furthermore, HCHO is a low-cost chemical feedstock with a gigantic annual yield while its oxidation product formate (and later formic acid) is a more valuable chemical28,29. Finally, coupling FOR with HER for H2 production may also provide environmental benefits if toxic formaldehyde residues in wastewater pollutants could be adopted as the feedstock.
Even though H2 generation from the electrochemical oxidation of HCHO has been reported on a few monometallic electrodes30,31,32, it remains less explored to couple it with water reduction for dual H2 production at both anode and cathode. Herein, we report a novel inexpensive electrocatalytic system, Cu3Ag7 and Ni3N/Ni as the anode and cathode electrocatalysts, respectively, to drive FOR and HER under alkaline conditions, which can produce H2 with an apparent 200% Faradaic efficiency and reach industrially relevant current densities of 100 and 500 mA/cm2 at cell voltages of only 0.22 and 0.60 V, respectively. Overall, the energy consumption of our two-electrode electrolyzer for H2 production is merely 0.30 and 0.70 kWh/m3 H2 at current densities of 100 and 500 mA cm−2, respectively, much lower than the theoretical energy demand of overall water splitting electrolysis (2.93 kWh/1 m3 H2).
Results and discussion
Screening of catalysts for formaldehyde oxidation
Inexpensive nitrate salts of copper and silver were utilized as the feedstocks to first prepare the corresponding monometallic electrocatalysts on glassy carbon rotating disk electrode (RDE) via a facile electrodeposition method (see the “Methods” section for details). As shown in Fig. 2, in the absence of HCHO, Cu/RDE showed a well-defined oxidation feature from Cu0 to Cu+ at ca. 0.5 V vs. RHE in 1.0 M KOH; while the oxidation peak of Ag0 to Ag+ from Ag/RDE did not appear until ~1.2 V vs. RHE. Upon the addition of 0.6 M HCHO, an apparent anodic current rise was observed beyond the onset potential (defined at 0.1 mA cm−2) of 0.05 V vs. RHE on Cu/RDE and a current density of 10 mA/cm2 was obtained at 0.4 V vs. RHE, indicating the electrochemical oxidation of HCHO on Cu/RDE. Despite the more positive onset potential (0.2 V vs. RHE) for HCHO oxidation, a much more rapid current rise was observed on Ag/RDE, which was able to produce an anodic current density of 26 mA/cm2 at 0.4 V RHE. The differences in onset potential and the anodic current rise of HCHO oxidation on Cu/RDE versus Ag/RDE prompted us to finely tune the ratio between Cu and Ag precursors in electrodeposition, aiming to synthesize a bimetallic CuAg electrocatalyst with optimized activity.
As shown in Supplementary Fig. 1, by systematically varying the Cu/Ag ratio from 9/1 to 1/9 (see the Supplementary Information for electrodeposition details), all the bimetallic CuAg/RDE electrodes possess similar electrochemical double layer capacitances (Cdl = 0.7–0.8 mF/cm2), close to those of the pristine monometallic samples (0.5–0.6 mF/cm2). Therefore, these bimetallic CuAg/RDE samples have similar electrochemical active surface area, which allows a fair comparison of their electrocatalytic activity of HCHO oxidation based on the measured geometric current density. Supplementary Fig. 2a plots the cyclic voltammograms (CVs) of all the CuAg/RDE samples as well as Cu/RDE and Ag/RDE measured under the same condition (0.6 M HCHO in 1.0 M KOH). It is apparent that Cu3Ag7/RDE exhibited the best performance (Supplementary Fig. 2b). The ICP-MS analysis result of Cu3Ag7/RDE confirmed the Cu/Ag ratio was 3:7. Therefore, all the subsequent electrochemical HCHO oxidation studies were carried out using Cu3Ag7 as the optimal electrocatalyst.
In the absence of HCHO, Cu3Ag7/RDE still retained the typical copper redox features of Cu+/0 and Cu2+/+ between 0.4 and 1.0 V vs. RHE but with suppressed current density (Fig. 2 inset) relative to that of Cu/RDE in 1.0 M KOH. Further positive scanning revealed an analogous oxidation feature of Ag0 to Ag+ beyond 1.2 V vs. RHE as observed for Ag/RDE. The addition of 0.6 M HCHO resulted in a drastic anodic current rise starting at ca 0.1 V vs. RHE, which was able to reach 66 mA/cm2 at 0.4 V vs. RHE (Fig. 2), substantially higher than those obtained on monometallic Cu/RDE (10 mA/cm2) and Ag/RDE (26 mA/cm2) at the same potential.
Using Cu3Ag7/RDE as a model electrode, we investigated the impact of HCHO concentration on the obtained current density (Supplementary Fig. 3) and it was found that 0.6 M HCHO produced the maximum current density at 0.4 V vs. RHE in 1.0 M KOH. Increasing the HCHO concentration beyond 0.6 M resulted in decreased anodic current, likely due to more disproportionation of HCHO at higher concentrations (Cannizzaro reaction)33. Next, the impact of OH− concentration was also probed and the results were compiled in Supplementary Fig. 4. In 1.0 M NaClO4, no anodic current was observed on Cu3Ag7/RDE between 0 and 0.4 V vs. RHE when 0.1 M HCHO was added. However, a slight increase to 1 mM [OH−] was able to produce a noticeable anodic current at 0.4 V RHE. A higher HCHO oxidation current was observed along the increase in [OH−]. Overall, these results demonstrate that an alkaline condition is necessary for the electrochemical oxidation of HCHO on Cu3Ag7/RDE.
Electrolysis performances
With the optimal Cu/Ag ratio in hand, we next sought to electrodeposit Cu3Ag7 on highly porous and conductive substrates for electrolysis studies. To avoid the introduction of other metal composites, commercially available copper foam was adopted as the catalyst support and current collector. A slightly modified electrodeposition approach was utilized to prepare Cu3Ag7 on copper foam (CF) and the resulting electrode was named Cu3Ag7/CF (see the “Methods” section for details). The scanning electron microscopy (SEM) image of a pristine copper foam indicates its porous skeleton with a smooth surface (Supplementary Fig. 5a). After the electrodeposition of Cu3Ag7, the as-prepared Cu3Ag7/CF shows nearly complete coverage of the copper foam by pine needle-like electrodeposits (Fig. 3a and Supplementary Fig. 5b). Energy-dispersive X-ray spectroscopy analysis (EDX) of Cu3Ag7/CF resulted in a Cu/Ag ratio very close to 3:7 (Supplementary Fig. 5c, d), in agreement with the ICP-MS results of Cu3Ag7/RDE. To shed light on the crystallinity of electrodeposited Cu3Ag7, X-ray diffraction was performed. In this case, carbon paper (CP), instead of copper foam, was used as the catalyst support, in order to avoid the interference of the background signal from the copper foam. The obtained XRD patterns of Cu/CP, Ag/CP, and Cu3Ag7/CP included in Fig. 3b confirmed that the bimetallic sample consists of both crystalline Cu (JCPDS Card no. 04-0836) and Ag (JCPDS Card no. 04-0783)34,35. The most prominent peaks at around 44° and 38° are corresponding to the (111) facets of Cu and Ag, respectively, which are preserved in Cu3Ag7/CP. To further investigate the structure of Cu3Ag7/CF, high-resolution transmission electron microscopy (HRTEM) combined with selected area electron diffraction (SAED) was performed. Supplementary Fig. 6a presents a clear dendritic structure in line with the SEM images (Fig. 3a and Supplementary Fig. 5c). The HRTEM images (Supplementary Fig. 6b, c) show the well-resolved lattice fringes with an inter-planar distance of 0.237 and 0.208 nm corresponding to the (111) crystal planes of cubic Ag and Cu, respectively. The distinct diffraction rings from SAED (Supplementary Fig. 6d) demonstrate the polycrystalline nature and could be indexed to the (111), (200), (220), and (311) planes of Ag and Cu36, respectively, in good agreement with the XRD results. High-angle-annular dark-field STEM (HAADF-TEM) and EDX element mapping images reveal a uniform distribution of Cu and Ag throughout the dendrites (Supplementary Fig. 6e).
Next, a two-compartment electrochemical cell (H-cell) with an anion exchange membrane was used to investigate the electrochemical HCHO oxidation on Cu3Ag7/CF. As shown in Fig. 3c, the CV curve of Cu3Ag7/CF collected in 1.0 M KOH with 0.6 M HCHO presents a nearly zero onset potential and very steep anodic current increase, reaching 100 and 500 mA/cm2 at merely 0.10 and 0.28 V vs. RHE, respectively. In sharp contrast, when electrodeposited nickel nanoparticles on nickel foam (Ni/NF) were employed as the OER electrocatalysts, much higher potentials (1.62 and 1.76 V vs. RHE) were required to reach the same current densities (100 and 500 mA/cm2). We previously reported an excellent earth-abundant HER electrocatalyst composed of interfaced Ni3N and Ni on nickel foam (Ni3Ni/Ni/NF) in 1.0 M KOH37. For the sake of comparison, we also included the CV curve of Ni3N/Ni/NF for the cathodic H2 evolution in Fig. 3c. With the above CVs, we were able to deduce that the voltage inputs for HER coupled with FOR would be much smaller to reach industrially relevant current densities like 100 and 500 mA/cm2, requiring only 0.20 and 0.58 V, respectively, when Cu3Ag7/CF and Ni3N/Ni/NF were employed as the anode and cathode electrocatalysts, respectively. However, much larger voltages were demanded (>1.7 V) for water splitting (HER/OER) to produce the same current density when using the Ni/NF (anode) and Ni3N/Ni/NF (cathode) catalyst couple. Indeed, as plotted in Fig. 3d, when a two-electrode electrolyzer of FOR/HER was assembled using Cu3Ag7/CF as the anode and Ni3N/Ni/NF as the cathode, the corresponding CV curve collected in 1.0 M KOH with 0.6 M HCHO only required cell voltages of 0.22 and 0.60 V to deliver the current densities of 100 and 500 mA cm−2, respectively, yet much higher cell voltages of 1.70 and 1.96 V were needed for conventional water splitting electrolysis. In short, this FOR/HER strategy using the Cu3Ag7/CF(+)||Ni3N/Ni/NF(–) electrode couple exhibited great superiority compared to reported systems of HER integrated with the oxidation of various inorganic and organic feedstocks (Table S1), in terms of applied voltage and Faradaic efficiency for H2 production.
Products analysis
Since the commercially purchased HCHO (37 wt% in H2O) contains methanol as a stabilizer and HCHO oxidation will produce formate under alkaline conditions, it is of critical importance to determine if Cu3Ag7/CF can catalyze the oxidation of methanol and formate within this small potential window. CV of Cu3Ag7/RDE from 0 to 0.4 V vs. RHE in 1.0 M KOH was first collected after the addition of 0.1 M formic acid, 0.1 M methanol, and 0.1 M HCHO, respectively. As shown in Supplementary Fig. 7, the increase in anodic current on Cu3Ag7/RDE was negligible upon the addition of either methanol or formic acid. However, a rapid anodic current rise was observed once HCHO was added, indicating that Cu3Ag7/RDE could effectively catalyze the electrooxidation of HCHO but not formic acid or methanol within this potential region, likely due to the smaller bond dissociation energy of C–H bond in H-CHO (88.0 ± 0.2 kcal mol−1) compared to all the bonds in methanol and formic acid38.
Figure 4a presents the chronoamperometry curve of Cu3Ag7/CF in 1.0 M KOH upon the continuous addition of 0.1 M formic acid, 0.1 M methanol, and 0.1 M HCHO. It is apparent that negligible anodic current increase was observed upon the addition of either formic acid or methanol with a voltage input of 0.6 V, indicating that Cu3Ag7/CF was not able to catalyze their electrochemical oxidation with this small voltage. In contrast, the addition of 0.1 M HCHO led to an immediate anodic current rise to 230 mA/cm2. These results prove that Cu3Ag7/CF possesses an excellent selectivity towards the electrochemical oxidation of HCHO with low voltage input, which is not affected by the presence of methanol and formate.
Gas chromatography was also performed to confirm (Supplementary Fig. 8) and quantify the amount of produced gas from the H-cell where Cu3Ag7/CF was employed as the anode and Ni3N/Ni/NF as the cathode in a two-electrode configuration. As shown in Fig. 4b, without applied voltage, no H2 was detected, suggesting that Cu3Ag7/CF was not able to thermocatalytically drive HCHO oxidation in 1.0 M KOH with 0.6 M HCHO at room temperature. Along with the increase of voltage input from 0.2 to 0.8 V, because of the faster H2 production rate, continuously decreased electrolysis time was needed to produce 2 mmol H2 from the anode chamber. Comparing the experimentally measured amount of H2 and the calculated amount of H2 based on passed charge during each electrolysis of different voltage inputs (0.2–0.8 V) confirmed that 100% Faradaic efficiency (FE) was achieved for anodic H2 production within the entire voltage range (Fig. 4b inset and Supplementary Fig. 9). In the meantime, cathodic H2 production from the Ni3N/Ni/NF cathode was also able to produce H2 with a 100% FE. For instance, Fig. 4c overlaps the measured H2 amounts over the theoretical H2 amounts along the passed charge for both cathode and anode chambers during electrolysis carried out at 0.8 V when 1.0 M KOH with 0.6 M HCHO was used as the anolyte and 1.0 M KOH as the catholyte. The nearly perfect alignment of the H2 amounts for both chambers confirmed that 100% FE of H2 production was realized for both electrodes and collectively 200% FE for overall H2 generation.
The organic products in the liquid phase of the anode chamber were determined and quantified to assess the carbon balance of electrolysis. The amounts of methanol and formate were determined from 1H NMR measurements using t-butanol as an internal standard (Supplementary Fig. 10). Besides the quantity resulting from the Cannizzaro reaction, all the additional formate was produced from the electrochemical HCHO oxidation (Supplementary Fig. 11 and Table S2). As shown in Fig. 4d, 100% FE of formate production was achieved for five consecutive 1 h controlled-current electrolysis (150 mA) using the Cu3Ag7/CF and Ni3N/Ni/NF couple but fresh electrolyte for each cycle. In the meantime, 200% FE of overall H2 production was retained for all five cycles as well. Further, the remaining HCHO was quantified via UV–vis absorption measurement following the Hantzsch reaction (see the “Methods” section for details)39, using a pre-established calibration curve (Supplementary Fig. 12). From the results (Supplementary Fig. 13 and Table S2) we conclude that 100% carbon balance of HCHO was maintained for the above five consecutive electrolysis cycles using the same electrode couple.
The stability of the Cu3Ag7/CF and Ni3N/Ni/NF electrode couple was further tested by both chronopotentiometry and chronoamperometry electrolysis. Figure 4e shows nearly identical chronopotentiometric curves for five consecutive controlled-current electrolysis conducted at 100 and 500 mA/cm2 in a fresh anolyte (1.0 M KOH and 0.6 M HCHO) of each cycle using the same electrode couple. In addition, a 7.5 h chronoamperometry experiment was carried out in the same electrolyte at a cell voltage of 0.6 V with the periodic replenishment of fresh HCHO back to its original 0.1 M concentration. Immediate resume of the anodic current was observed for each period (Fig. 4f). Post-electrolysis characterization of Cu3Ag7/CF displayed negligible changes in morphology, crystallinity, and electrochemical double-layer capacitance (Fig. 3b and Supplementary Figs. 14, 15). Overall, these results corroborate the superior structural robustness and mechanical stability of Cu3Ag7/CF for long-term electrochemical HCHO oxidation for anodic H2 production with low voltage input.
Theoretical computations
To shed light on the improved performance of the bimetallic Cu3Ag7/CF relative to monometallic Cu/CF and Ag/CF in the anodic H2 production from electrocatalytic HCHO oxidation, density functional theory (DFT) computation was performed to examine the structure and energetics of key steps during FOR. Because only a small voltage is needed to drive FOR, one can assume that the electrocatalytic reaction proceeds close to the thermodynamic limit. Under thermal conditions, the commonly accepted mechanism of FOR is that HCHO first becomes hydrated and deprotonated in the alkaline solution to yield the H2C(OH)O anion, which then adsorbs on the catalyst surface40,41. The resulting H2C(OH)O* intermediate is dehydrogenated via C-H cleavage to yield HCOOH* and H* (Fig. 5a), which is a key step we focus on. Our experimental characterization showed that the (111) facets are preferentially exposed for the Cu, Ag, and Cu3Ag7 catalysts, so we used the (111) surfaces to compare the three catalysts (see Supplementary Fig. 16a for the details of the models). First, we compared the relative adsorption energy of the H2C(OH)O* intermediate: as shown in Fig. 5b, adsorption on Cu3Ag7 is most preferred, with the O group anchored at the Cu2Ag1 hollow site; the top view shows a clear staggered conformation of the H2COH group relative to the Cu2Ag1 site (Fig. 5c), distinct from the more eclipsed conformations on Cu(111) and Ag(111) (Supplementary Fig. 16b). Analysis of the projected density of states of the anchored O group of H2C(OH)O* at the Cu2Ag1 site indicates that there are strong orbital mixings of O 2p states with Cu 3d states from −1.5 to −1.0 eV as well as with Ag 4d states from –6 to –5 and –4 to –3 eV (Supplementary Fig. 16c). In other words, the existence of the separate two d-bands on the bimetallic surface provides more flexibility in adsorbing and stabilizing the H2C(OH)O* intermediate. Indeed, C–H cleavage is much more facile on Cu3Ag7 from the staggered adsorption conformation (Fig. 5d). After C–H cleavage, the formation of H2 from two H* was found to be facile as well on Cu3Ag7 (Fig. 5e): the energy barrier is 0.66 eV, which is expected to be further lowered when entropy is taken into account. To complete the reaction, HCOOH* will desorb from the surface and then deprotonate to form formate in the solution.
Electrocatalytic paraformaldehyde oxidation and energy efficiency analysis
The promising activity of Cu3Ag7 towards HCHO oxidation to produce H2, corroborated by our DFT results, prompted us to further expand the substrate scope. Especially, we were motivated to explore the possibility of utilizing paraformaldehyde as the feedstock for the following reasons. In contrast to HCHO aqueous solutions with limited concentration (e.g., 37 wt%) and containing methanol as the stabilizer, paraformaldehyde is solid under ambient conditions, possessing much higher mass density and also lower cost42. It is known that HCHO can be released from paraformaldehyde when dissolved in an aqueous solution43. To our delight, as shown in Supplementary Fig. 17a, Cu3Ag7/RDE still exhibited excellent electrocatalytic activity for the oxidation of paraformaldehyde, superior to Cu/RDE and Ag/RDE. Concentration dependence experiments indicated that 10.0 g/L paraformaldehyde resulted in the highest oxidation current density (60 mA/cm2) on Cu3Ag7/RDE in 1.0 M KOH (Supplementary Fig. 17b). Figure 6a compares the CV curves collected on Cu3Ag7/CF and Ni/NF in the presence and absence of 10.0 g/L paraformaldehyde, respectively. It is apparent that much smaller potentials of 0.13 and 0.36 V vs. RHE are required to produce 100 and 500 mA/cm2, respectively, than those required for OER on Ni/NF. Nearly unity Faradaic efficiencies were obtained for both H2 and formate production when paraformaldehyde was employed as the feedstock and Cu3Ag7/CF as the anode electrocatalyst at different applied potentials from 0.1 to 0.4 V vs. RHE (Fig. 6b, Supplementary Figs. 8b and 18, and Table S3). Notably, when paraformaldehyde was used as the oxidation substrate, the yields of methanol and formate from the competing Cannizzaro reaction were much lower than those directly using HCHO solutions, suggesting another advantage of using paraformaldehyde as the feedstock for our dual HER strategy. The long-term stability test of electrolysis using paraformaldehyde was also carried out using a flow cell consisting of AEM and Ni3N/Ni/NF(–)||Cu3Ag7/CF(+) electrode couple in a zero-gap configuration. The electrolysis was performed at 100 mA cm−2 with 1.0 M KOH as the catholyte and 1.0 M KOH plus 10.0 g/L paraformaldehyde as the anolyte, both of which were fed into the cell at a flow rate of 50 mL min−1. The electrolyte was refreshed every 24 h. Supplementary Fig. 19 demonstrates that our dual H2 production strategy (HER/FOR) using the Ni3N/Ni/NF(–)||Cu3Ag7/CF(+) electrode couple can maintain a low voltage input (0.4–0.6 V without iR correction) to deliver 100 mA cm−2 over 260 h, indicating the great robustness of our electrocatalysts for dual H2 production.
From an energy efficiency perspective, our dual H2 production system surpasses those conventional water-splitting systems to a substantial extent. For instance, Fig. 6c compares the electricity consumption between our dual H2 production strategy (HER/FOR) using the Ni3N/Ni/NF(–)||Cu3Ag7/CF(+) electrode couple and traditional water electrolysis (HER/OER) using the Ni3N/Ni/NF(–)||Ni/NF(+) electrode couple. To produce H2 at a current density of 100 mA/cm2, our dual H2 production system only requires 0.30 kWh of electricity per m3 H2 whereas conventional water splitting demands 4.10 kWh. Even at an industrially applicable current density of 500 mA/cm2, the electricity consumption of our dual H2 production system is still as small as 0.70 kWh/m3 H2, much lower than that of water electrolysis (4.70 kWh/m3 H2).
In summary, we report a bimetallic electrocatalyst Cu3Ag7 for efficient H2 production at the anode of an electrolyzer which integrates the partial oxidation of formaldehyde with water reduction to realize dual HER with an apparent 200% Faradaic efficiency. DFT computation reveals a key adsorption conformation of the H2C(OH)O* intermediate on Cu3Ag7 that is highly conducive to C–H cleavage. In addition to formaldehyde solution, solid-phase paraformaldehyde can be equally employed as a reactant to realize similar performance, paving the way for practical application on a large scale.
Methods
Chemicals
All chemicals were used as received without any further purification. Copper(II) nitrate hydrate, silver nitrate, copper(II) sulfate pentahydrate, silver sulfate, potassium hydroxide (>85%), formaldehyde solution (37 wt% in H2O), paraformaldehyde, formic acid (>99%), methanol (>99.9%), tert-butanol (anhydrous), hydrochloric acid (ACS reagent, 37%), sodium citrate were purchased from Sigma Aldrich. Ammonium chloride and nickel(II) chloride hexahydrate were purchased from Alfa Aesar. Copper foam and nickel foam with a purity >99.99% were purchased from MTI. Deionized water (18 MΩ cm) from a Barnstead E-Pure system was used in all experiments.
Synthesis
Synthesis of Cu, Ag, and CuAg catalysts on rotating disk electrode
The catalysts were synthesized through a convenient and straightforward electrodeposition method by using a typical three-electrode system on a VMP-3 potentiostat (Biologic Science Instrument). A rotating disk electrode with glassy carbon (RDE, 0.196 cm−2, Pine Research Instrumentation) was used as the working electrode with a leakless Ag/AgCl (eDAQ) reference electrode and a Pt mesh counter electrode. –0.2 V vs. Ag/AgCl was applied to the RDE working electrode for the reduction of Cu and Ag ions in the electrolyte. The electrodeposition ended when a charge of 60 mC had been passed. Cu modified on RDE (Cu/RDE) and Ag modified on RDE (Ag/RDE) were electrodeposited at –0.2 V vs. Ag/AgCl from an aqueous electrolyte containing specific amounts of Cu(NO3)2 (20.0 mM, 30 mL) and AgNO3 (20.0 mM, 30 mL), respectively. For comparison, the CuxAg10−x/RDE (x = 1, 3, 5, 7, and 9) were prepared under the same conditions from precursor electrolytes (20.0 mM, 30.0 mL) containing AgNO3 and Cu(NO3)2 solutions with different concentration ratios (from 1/9 to 9/1).
Synthesis of Cu3Ag7 catalysts on Cu foam (Cu3Ag7/CF)
To avoid the introduction of other metal composites, copper foam (0.5 cm × 0.5 cm) was used as the catalyst support and current collector. The copper foam was sequentially washed with 1.0 M HCl, ethanol, and deionized water (each for 10 min). Cu3Ag7/CF was synthesized through electrodeposition on a Gamry Interface 1000 electrochemical workstation with a three-electrode configuration, using a carbon rod and a leakless Ag/AgCl (eDAQ) electrode as the counter electrode and reference electrode, respectively. Cu3Ag7/CF was electrodeposited at a constant current of –3.0 A cm−2 for 30 s from an aqueous electrolyte (30 mL) containing specific amounts of Ag2SO4 (14.0 mM) and CuSO4 (6.0 mM) in 1.5 M H2SO4 under Ar without stirring. In addition, 0.1 M sodium citrate was added to the precursor as a complexing agent. To avoid the interference of the background signal from copper foam in the XRD tests, we prepared Cu-modified, Ag-modified, and Cu3Ag7-modified carbon paper electrodes (Cu/CP, Ag/CP, and Cu3Ag7/CP) samples following the same preparation conditions. The only difference is that copper foam was replaced by carbon paper.
Synthesis of Ni/NF and Ni3N/Ni/NF
Based on our previous work37, the Ni3N/Ni/NF electrode was synthesized from the electrodeposition of Ni particles on a nickel foam followed by thermal nitridation. A piece of clean nickel foam (0.5 cm × 0.5 cm) was used as the working electrode. A carbon rod was used as the counter electrode. The Ni/NF was synthesized through electrodeposition at a constant current density of −1.0 A cm−2 for 500 s in a two-electrode cell containing NiCl2 (0.1 M) and NH4Cl (2.0 M) under Ar without stirring. The Ni3N/Ni/NF was obtained from the thermal annealing of Ni/NF under an NH3 flow at 300 °C for 6 h with a ramping rate of 10 °C min−1.
Physical characterization
The morphology features of samples were assessed by using scanning electron microscopy (FEI XL30, 15 kV), as well as transmission electron microscopy (TEM), selective area electron diffraction (SAED, 40 μm aperture), and scanning transmission electron microscopy (STEM) with an FEI Tecnai Osiris (200 kV). Samples for TEM were prepared by suspending dry Cu3Ag7/CF electrocatalyst on carbon-coated 200-mesh copper TEM grids (Ted Pella 01894-F). STEM−energy-dispersive X-ray spectroscopy (EDX) maps were collected using Bruker Esprit 1.9 software and averaged over 8 scans. X-ray diffraction (XRD) patterns were collected on a Philips X’Pert Pro PW3040/00 (PAN analytical) instrument. The scan range was set from 20° to 90° (in 2θ) with a Cu-tube operated at 45 kV and 40 mA. The evolved H2 through the electrolysis process was quantified by gas chromatography (GC, SRI 8610C) equipped with a Molecular Sieve 13 packed column, a HayesSep D packed column, and a thermal conductivity detector, and Ar was used as the carrier gas. The Cu and Ag quantities of the sample were analyzed via inductively coupled plasma mass spectrometry (ICP-MS, Agilent 7700 series) in 2% nitric acid. 1H NMR spectra were recorded in the designated solvents on a Bruker AV 400 MHz spectrometer. UV–vis absorption spectra were collected on an Agilent 8454 UV–Vis Spectrophotometer.
Electrochemical measurements
All catalysts on RDE were tested on an electrochemical workstation (VMP-3 potentiostat, Biologic Science Instrument) with a modulated speed rotator (PINE Research Instrumentation) at room temperature in a standard three-electrode configuration. An RDE (0.196 cm2) was utilized as the working electrode, while a Pt mesh and a Hg/HgO (1.0 M KOH) electrode were used as the counter electrode and reference electrode, respectively. All potentials herein were referenced to the reversible hydrogen electrode (RHE) through calibration via Pt foil as the working electrode in the H2-saturated electrolyte. All potentials measured in 1.0 M KOH were converted to the value versus RHE according to the equation: ERHE = EHg/HgO + 0.924 V. Commercial formaldehyde (37 wt%) solution was directly used as the oxidation substrate. The Cu/RDE, Ag/RDE, and CuxAg10−x/RDE were treated using cyclic voltammetry (CV) from 0 to 0.3 VRHE at 50 mV s−1 for 20 cycles to obtain metallic Cu or Ag in 1.0 M KOH under Ar prior to the HCHO electrooxidation (FOR) test (Supplementary Fig. 20). All CVs of FOR were performed in the electrolyte under Ar at a scan rate of 10 mV s−1 and a rotation rate of 1500 rpm without iR correction in a standard three-electrode configuration. For investigating the effect of [OH–], 1.0 M anion concentration anolyte consisted of NaOH and NaClO4 with different concentrations to avoid the interference of conductivity change. All potentials herein were referenced to the reversible hydrogen electrode (RHE) through calibration using Pt foil as the working electrode in H2-saturated electrolytes with different OH– concentrations. The electrochemical double-layer capacitance (Cdl) measurements were performed using cyclic voltammetry, which was collected in a non-Faradaic region with various scan rates ranging from 20 to 200 mV s−1 at potentials between 0.07 and 0.17 V vs. RHE in 1.0 M KOH under Ar. For paraformaldehyde oxidation on RDE, all experimental procedures were the same as FOR.
The measurements of FOR on Cu3Ag7/CF, HER on Ni3Ni/Ni/NF, and OER on Ni/NF were conducted on the VMP-3 potentiostat in an H-cell with an anion exchange membrane (Fumasep FAA-3-50), using a Pt mesh as the counter electrode and a Hg/HgO (1.0 M KOH) as the reference electrode, respectively. Cu3Ag7/CF was treated using cyclic voltammetry from 0 to 0.3 VRHE at 50 mV s−1 for 20 cycles to obtain metallic Cu or Ag in 1.0 M KOH under Ar prior to the HCHO electrooxidation test. All CVs (FOR, HER and OER) in a three-electrode configuration were collected at a scan rate of 10 mV s−1 without iR correction. The two-electrode electrolysis was performed on an electrochemical workstation in H-cell with an anion exchange membrane. For conventional water electrolysis, the Ni/NF and Ni3Ni/Ni/NF were employed as the anode and cathode in 1.0 M KOH, respectively. For a two-electrode electrolyzer of FOR/HER, Cu3Ag7/CF was the anode and Ni3N/Ni/NF was the cathode, in which 1.0 M KOH and 0.6 M HCHO were used as the anolyte and 1.0 M KOH as the catholyte. The uncompensated resistance (Ru) of 1.0 M KOH in the absence or presence of HCHO was determined by the Current Interrupt (CI) method of a VMP-3 potentiostat and the value of Ru was measured as 15 ± 0.2 Ω. All CVs in a two-electrode configuration were collected under Ar at a scan rate of 10 mV s−1 with iR compensation by the automatic CI method with a value of 90% × Ru through the EC-lab software. For the gas products analysis from the anode chamber, different cell voltages (0.2–0.8 V) were applied for chronoamperometry where Cu3Ag7/CF was employed as the anode and Ni3N/Ni/NF as the cathode in a two-electrode configuration. The Faradaic efficiency analysis of H2 and formate production in the cathode and anode chambers was performed from five consecutive 1 h controlled-current electrolysis (150 mA) using the Cu3Ag7/CF and Ni3N/Ni/NF couple but fresh electrolyte for each cycle. The chronopotentiometry test was performed by five consecutive controlled-current electrolysis conducted at 100 and 500 mA/cm2 in a fresh anolyte (1.0 M KOH and 0.6 M HCHO) of each cycle using the Ni3N/Ni/NF(–)||Cu3Ag7/CF(+) electrode couple. The chronoamperometry measurement was carried out at a cell voltage of 0.6 V with the periodic replenishment of fresh HCHO back to its original 0.1 M concentration. For the electrocatalytic paraformaldehyde oxidation on Cu3Ag7/CF, all experimental procedures were the same as FOR. The long-term stability test was carried out in a home-made flow cell with serpentine flow channels (1 cm × 1 cm) using Cu3Ag7/CF as the anode and Ni3N/Ni/NF as the cathode on a Biologic VMP-3 potentiostat without iR-compensation. The catholyte (1.0 M KOH) and anolyte (1.0 M KOH and 10.0 g/L PFA) were fed into the cell at a flow rate of 50 mL min−1 by a peristaltic pump (Peri-Star Pro Peristaltic Pump, World Precision Instruments) and recycled. The electrolyte was refreshed every 24 h. An anion exchange membrane (Fumasep FAA-3-50) was used to separate the anolyte and catholyte.
Product analysis
The evolved H2 in both anode chamber and cathode chamber of a two-electrode electrolyzer of FOR/HER was analyzed by gas chromatography (GC, SRI 8610C) equipped with a Molecular Sieve 13 packed column, a HayesSep D packed column, and a thermal conductivity detector. The oven is kept at 80 °C using Ar as carrier gas. The quantity of H2 production was determined via a water displacement method.
The concentration of formaldehyde during electrolysis was quantified via UV–vis absorption measurement following the Hantzsch reaction39. Ammonium acetate (15.4 g) in water (50 mL), glacial acetic acid (0.3 mL), and acetylacetone (0.2 mL) were mixed to form a solution under stirring, which was further diluted with water (49.5 mL). To measure the concentration of formaldehyde, 20.0 µL of anolyte was acidified by 20 µL 2.0 M HCl and then diluted 2500 times prior to and post-electrolysis. Subsequently, 2.0 mL of the diluted solution was mixed with the acetylacetone solution (2.0 mL), which was further heated to 60 °C for 10 min. After cooling for 10 min, the absorbance of the sample solution at 413 nm was measured. The quantification of HCHO was obtained from the calibration curves by applying standard solutions with known concentrations of commercially purchased pure HCHO.
The identification and quantification of formic acid and methanol were determined from the 1H NMR using calibration curves with t-butanol (10.0 mM) as an internal standard. 100 µL electrolyte from anolyte and catholyte prior to and post electrolysis was acidified by 20 µL HCl (37%) and then added into 500 µL D2O. 1H NMR was recorded using a water suppression method.
The Faradaic efficiency was calculated on the basis of the following equation:
where n is the number of electrons transferred for each product molecule, F is Faraday’s constant (96,485 C mol−1), N is the mole number of products and Q is the total passed charge.
The carbon balance (%) of the electrooxidation process was calculated using the following equation:
Theoretical computation
Density functional theory (DFT) calculations were performed by using Vienna Ab initio Simulation Package (VASP)44,45. The Perdew–Burke–Ernzerhof (PBE) functional within the generalized gradient approximation (GGA) was used for electron exchange correlation46. Projector augmented wave (PAW) potential was used to treat the nuclei-electron interaction47,48. An energy cutoff of 400 eV was chosen for plane wave basis sets. The atomic positions were relaxed until the force on each atom was <0.05 eV/Å. Electronic energies converged within 10−4 eV. Transition states were searched using the Climbing Image Nudged Elastic Band approach49,50. Frequency analysis was carried out to ensure that there was only a single imaginary frequency for the transition state.
The bulk model of Cu3Ag7 was built based on the bulk model of Ag. Starting with a 2 × 2 × 2 supercell of bulk Ag with 16 Ag atoms, we replaced two Ag atoms with Cu and obtained four different geometries for Cu2Ag14. After optimization, the lowest energy structure was used as a starting structure to generate six different geometries for Cu3Ag13 from replacing one Ag in Cu2Ag14 with Cu. Repeating the optimization and the single-atom substitution of the lowest-energy structure, seven geometries of Cu4Ag12 and two geometries of Cu5Ag11 were tested and compared. In total, over 20 bulk geometries were examined for a stable structure for Cu5Ag11 (Cu/Ag = 0.45) which was used to approximate the bulk Cu3Ag7 (Cu/Ag = 0.43) composition. A slab with five layers in a (3 × 3) lateral supercell was built for Cu3Ag7, Ag, and Cu (111) surfaces and sampled by 2 × 2 × 1 k-point mesh. The bottom two layers were fixed, and the other atoms were all relaxed during the structural optimization. The vacuum layer was set to be 15 Å. Coordinates for the bulk model and the (111) surface of the bimetallic system are provided in Supplementary Data 1.
Data availability
All data are available in the manuscript, the supplementary materials and from the authors on request. Source data are provided as a Source Data file. Source data are provided with this paper.
References
Jacobson, M. Z., Colella, W. G. & Golden, D. M. Cleaning the air and improving health with hydrogen fuel-cell vehicles. Science 308, 1901–1905 (2005).
United States Department of Energy. A National Vision of America’s Transition to a Hydrogen Economy-to 2030 and Beyond (United States Department of Energy, 2003).
International Energy Agency (IEA). The Future of Hydrogen (International Energy Agency (IEA), 2019).
Turner, J. A. Sustainable hydrogen production. Science 305, 972–974 (2004).
Chatenet, M. et al. Water electrolysis: from textbook knowledge to the latest scientific strategies and industrial developments. Chem. Soc. Rev. 51, 4583–4762 (2022).
Wang, J. et al. Non-precious-metal catalysts for alkaline water electrolysis: operando characterizations, theoretical calculations, and recent advances. Chem. Soc. Rev. 49, 9154–9196 (2020).
Zhu, J., Hu, L., Zhao, P., Lee, L. Y. S. & Wong, K. Y. Recent advances in electrocatalytic hydrogen evolution using nanoparticles. Chem. Rev. 120, 851–918 (2020).
Lagadec, M. F. & Grimaud, A. Water electrolysers with closed and open electrochemical systems. Nat. Mater. 19, 1140–1150 (2020).
Zhang, L., Wang, Z. & Qiu, J. Energy-saving hydrogen production by seawater electrolysis coupling sulfion degradation. Adv. Mater. 34, 2109321 (2022).
You, B. & Sun, Y. Innovative strategies for electrocatalytic water splitting. Acc. Chem. Res. 51, 1571–1580 (2018).
You, B., Han, G. & Sun, Y. Electrocatalytic and photocatalytic hydrogen evolution integrated with organic oxidation. Chem. Commun. 54, 5943–5955 (2018).
Li, R., Xiang, K., Peng, Z., Zou, Y. & Wang, S. Recent advances on electrolysis for simultaneous generation of valuable chemicals at both anode and cathode. Adv. Energy Mater. 11, 2102292 (2021).
You, B., Jiang, N., Liu, X. & Sun, Y. Simultaneous H2 generation and biomass upgrading in water by an efficient noble-metal-free bifunctional electrocatalyst. Angew. Chem. Int. Ed. 55, 9913–9917 (2016).
You, B., Liu, X., Jiang, N. & Sun, Y. A General strategy for decoupled hydrogen production from water splitting by integrating oxidative biomass valorization. J. Am. Chem. Soc. 138, 13639–13646 (2016).
Jiang, N., You, B., Boonstra, R., Terrero Rodriguez, I. M. & Sun, Y. Integrating electrocatalytic 5-hydroxymethylfurfural oxidation and hydrogen production via Co–P-derived electrocatalysts. ACS Energy Lett. 1, 386–390 (2016).
Jiang, N. et al. Electrocatalysis of furfural oxidation coupled with H2 evolution via nickel-based electrocatalysts in water. ChemNanoMat 3, 491–495 (2017).
You, B., Liu, X., Liu, X. & Sun, Y. Efficient H2 evolution coupled with oxidative refining of alcohols via a hierarchically porous nickel bifunctional electrocatalyst. ACS Catal. 7, 4564–4570 (2017).
Forslund, R. P., Alexander, C. T., Abakumov, A. M., Johnston, K. P. & Stevenson, K. J. Enhanced electrocatalytic activities by substitutional tuning of nickel-based ruddlesden–popper catalysts for the oxidation of urea and small alcohols. ACS Catal. 9, 2664–2673 (2019).
Chen, W. et al. Unveiling the electrooxidation of urea: intramolecular coupling of the N–N bond. Angew. Chem. Int. Ed. 60, 7297–7307 (2021).
Zhang, M. et al. An efficient symmetric electrolyzer based on bifunctional perovskite catalyst for ammonia electrolysis. Adv. Sci. 8, 2101299 (2021).
Zhu, Y. et al. Dual nanoislands on Ni/C hybrid nanosheet activate superior hydrazine oxidation-assisted high-efficiency H2 production. Angew. Chem. Int. Ed. 61, e202113082 (2022).
Zhang, X. et al. Efficient hydrogen generation from the NaBH4 hydrolysis by cobalt-based catalysts: positive roles of sulfur-containing salts. ACS Appl. Mater. Interfaces 12, 9376–9386 (2020).
Wang, Q. et al. Dramatic synergy in CoPt nanocatalysts stabilized by “click” dendrimers for evolution of hydrogen from hydrolysis of ammonia borane. ACS Catal. 9, 1110–1119 (2018).
Fu, F. et al. Highly selective and sharp volcano-type synergistic Ni2Pt@ZIF-8-catalyzed hydrogen evolution from ammonia borane hydrolysis. J. Am. Chem. Soc. 140, 10034–10042 (2018).
Choi, B.-S. et al. Core–shell engineering of Pd–Ag bimetallic catalysts for efficient hydrogen production from formic acid decomposition. ACS Catal. 9, 819–826 (2018).
Li, S. J. et al. A simple and effective principle for a rational design of heterogeneous catalysts for dehydrogenation of formic acid. Adv. Mater. 31, 1806781 (2019).
Ken-ichi, M. & Michio, E. Formaldehyde electro-oxidation on copper metal and copper-based amorphous alloys in alkaline media. Bull. Chem. Soc. Jpn. 58, 2043–2050 (1985).
Trincado, M., Grützmacher, H. & Prechtl, M. H. G. CO2-based hydrogen storage—hydrogen generation from formaldehyde/water. Phys. Sci. Rev. 3, 20170013 (2018).
Bulushev, D. A. & Ross, J. R. H. Towards sustainable production of formic acid. ChemSusChem 11, 821–836 (2018).
Meerakker, J. E. A. M. V. D. On the mechanism of electroless plating. I. Oxidation of formaldehyde at different electrode surfaces. J. Appl. Electrochem. 11, 387–393 (1981).
Beltowska-Brzezinska, M. Electrochemical oxidation of formaldehyde on gold and silver. Electrochim. Acta 30, 1193–1198 (1985).
Beltowska-Brzezinska, M. & Heitbaum, J. On the anodic oxidation of formaldehyde on Pt, Au and Pt/Au-alloy electrodes in alkaline solution. J. Electroanal. Chem. 183, 167–181 (1985).
Martin, R. J. L. The mechanism of the Cannizzaro reaction of formaldehyde. Aust. J. Chem. 7, 335–347 (1954).
Dutta, A., Rahaman, M., Luedi, N. C., Mohos, M. & Broekmann, P. Morphology matters: tuning the product distribution of CO2 electroreduction on oxide-derived Cu foam catalysts. ACS Catal. 6, 3804–3814 (2016).
Dutta, A., Morstein, C. E., Rahaman, M., Cedeño López, A. & Broekmann, P. Beyond copper in CO2 electrolysis: effective hydrocarbon production on silver-nanofoam catalysts. ACS Catal. 8, 8357–8368 (2018).
Deo Malviya, K., Srivastava, C. & Chattopadhyay, K. Phase formation and stability of Ag–60 at%Cu alloy nanoparticles synthesized by chemical routes in aqueous media. Phys. Chem. Chem. Phys. 19, 28006–28013 (2017).
Song, F. et al. Interfacing nickel nitride and nickel boosts both electrocatalytic hydrogen evolution and oxidation reactions. Nat. Commun. 9, 4531 (2018).
Blanksby, S. J. & Ellison, G. B. Bond dissociation energies of organic molecules. Acc. Chem. Res. 36, 255–263 (2003).
Nash, T. The colorimetric estimation of formaldehyde by means of the Hantzsch reaction. Biochem. J. 55, 416–421 (1953).
Kapoor, S., Barnabas, F. A., Sauer, M. C., Meisel, D. & Jonah, C. D. Kinetics of hydrogen formation from formaldehyde in basic aqueous-solutions. J. Phys. Chem. 99, 6857–6863 (1995).
ten Kortenaar, M. V., Kolar, Z. I., de Goeij, J. J. M. & Frens, G. Adsorption, exchange, and oxidation of formaldehyde on gold: a radiotracer study. Langmuir 18, 10279–10291 (2002).
Fetzer, M. N. A., Tavakoli, G., Klein, A. & Prechtl, M. H. G. Ruthenium‐catalyzed e‐selective partial hydrogenation of alkynes under transfer‐hydrogenation conditions using paraformaldehyde as hydrogen source. ChemCatChem 13, 1317–1325 (2021).
Suenobu, T., Isaka, Y., Shibata, S. & Fukuzumi, S. Catalytic hydrogen production from paraformaldehyde and water using an organoiridium complex. Chem. Commun. 51, 1670–1672 (2015).
Kresse, G. & Furthmuller, J. Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set. J. Comput. Mater. Sci. 6, 15–50 (1996).
Kresse, G. Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set. Phys. Rev. B 54, 11169–11186 (1996).
Perdew, J. P., Burke, K. & Ernzerhof, M. Generalized gradient approximation made simple. Phys. Rev. Lett. 77, 3865–3868 (1996).
Blochl, P. E., Jepsen, O. & Andersen, O. K. Improved tetrahedron method for Brillouin-zone integrations. Phys. Rev. B 49, 16223–16233 (1994).
Kresse, G. & Joubert, D. From ultrasoft pseudopotentials to the projector augmented-wave method. Phys. Rev. B 59, 1758–1775 (1999).
Henkelman, G. & Jo´nsson, H. Improved tangent estimate in the nudged elastic band method for finding minimum energy paths and saddle points. J. Chem. Phys. 113, 9978 (2000).
Henkelman, G., Uberuaga, B. P. & Jo´nsson, H. A climbing image nudged elastic band method for finding saddle points and minimum energy paths. J. Chem. Phys. 113, 9901–9904 (2000).
Acknowledgements
Y.S. acknowledges the support of the National Science Foundation (CHE-1914546 and CHE-2102220) and Herman Frasch Foundation (820-HF17). DFT computation (D.J.) was sponsored by the National Science Foundation (CHE-2102191).
Author information
Authors and Affiliations
Contributions
Y.S. conceived and designed this research. G.L. and G.H. synthesized and characterized the catalysts and performed electrocatalysis experiments. L.W. and D.J. conducted the theoretical computation. G.L. and X.C. carried out the ICP-MS measurements. N.K.M. and P.R.K. performed TEM and HR-TEM measurements. All authors contributed to the analysis and interpretation of the results. G.L., Y.S., and D.J. wrote the manuscript.
Corresponding authors
Ethics declarations
Competing interests
Y.S. has filed a provisional patent application related to this manuscript (US patent provisional 63/440,048). All other authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Source data
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Li, G., Han, G., Wang, L. et al. Dual hydrogen production from electrocatalytic water reduction coupled with formaldehyde oxidation via a copper-silver electrocatalyst. Nat Commun 14, 525 (2023). https://doi.org/10.1038/s41467-023-36142-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-023-36142-7
This article is cited by
-
Pd/NiMoO4/NF electrocatalysts for the efficient and ultra-stable synthesis and electrolyte-assisted extraction of glycolate
Nature Communications (2024)
-
Electrochemical hydrogenation and oxidation of organic species involving water
Nature Reviews Chemistry (2024)
-
Interfacial Electronic Modulation of Dual-Monodispersed Pt–Ni3S2 as Efficacious Bi-Functional Electrocatalysts for Concurrent H2 Evolution and Methanol Selective Oxidation
Nano-Micro Letters (2024)
-
Capturing critical gem-diol intermediates and hydride transfer for anodic hydrogen production from 5-hydroxymethylfurfural
Nature Communications (2023)
-
Green electrosynthesis of 3,3’-diamino-4,4’-azofurazan energetic materials coupled with energy-efficient hydrogen production over Pt-based catalysts
Nature Communications (2023)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.