Abstract
Tailored nanostructures provide at-will control over the properties of light, with applications in imaging and spectroscopy. Active photonics can further open new avenues in remote monitoring, virtual or augmented reality and time-resolved sensing. Nanomaterials with χ(2) nonlinearities achieve highest switching speeds. Current demonstrations typically require a trade-off: they either rely on traditional χ(2) materials, which have low non-linearities, or on application-specific quantum well heterostructures that exhibit a high χ(2) in a narrow band. Here, we show that a thin film of organic electro-optic molecules JRD1 in polymethylmethacrylate combines desired merits for active free-space optics: broadband record-high nonlinearity (10-100 times higher than traditional materials at wavelengths 1100-1600 nm), a custom-tailored nonlinear tensor at the nanoscale, and engineered optical and electronic responses. We demonstrate a tuning of optical resonances by Δλ = 11 nm at DC voltages and a modulation of the transmitted intensity up to 40%, at speeds up to 50 MHz. We realize 2 × 2 single- and 1 × 5 multi-color spatial light modulators. We demonstrate their potential for imaging and remote sensing. The compatibility with compact laser diodes, the achieved millimeter size and the low power consumption are further key features for laser ranging or reconfigurable optics.
Similar content being viewed by others
Introduction
Recent advances in both traditional and novel electro-optic materials that exhibit a χ(2) nonlinearity have resulted into an unprecedented richness of active photonic devices, that find applications in communications1,2,3, electric field metrology4,5, dynamic beam steering6, and quantum science7. Multi-pixel, large-area spatial light modulators (SLMs) are a prerequisite to achieve massively parallel dynamic and reconfigurable control over the diverse properties of light. They promise to revolutionize applications in industry and fundamental science. In reconfigurable photonics, multipixel optical components can control light on-demand, but they need to be compact and consume minimal power per pixel. In massively parallel remote sensing8, high-speed SLMs can generate parallel optical channels that scan the environment in three dimensions, but operation at high speeds is mandatory to resolve small changes in the position and velocity of objects within a short timeframe. In the area of ultrafast optics, SLMs can manipulate femtosecond pulses through pulse-pickers, but must accommodate a broad optical bandwidth and switching speeds commensurate with the repetition rate of these lasers, typically around few MHz to GHz. In fundamental science, SLMs play a crucial role e.g., in the sorting and reconfiguration of cold atoms for quantum simulation9, and reaching higher speeds can access entirely new physics. In industry applications, such as self-driving cars10, high-speed SLMs can monitor a scene if they are compatible with low-power electronic circuits, chip-based laser diodes that typically have a broad linewidth and low foot-print packaging.
Among all existing SLM technologies, SLMs that employ electric tuning enabled by χ(2) materials are outstanding candidates to reach high speeds in parallel multipixel architectures. They are intrinsically compatible with massively parallel radio-frequency (RF) electronic circuits that promise to deliver the necessary electrical controls by hybrid electronic-optical integration. In this case, the SLM is essentially a two-dimensional array of free-space electro-optic modulators. Commercial SLMs instead use bulky digital micro-mirror arrays11 or liquid crystals12, which not only limit them to around 10 kHz but also do not employ nanostructures. Few state-of-the art SLM demonstrations address the quest for ever-higher speed by making use of narrow-band surface plasmon resonances in rather complex prism-based schemes using χ(2) nonlinear materials13, but the nano-scale engineering of the individual pixels remains unexplored and the employed nonlinearity is rather low. Flat lens technology around metasurfaces14 is a powerful platform that permits engineering of the properties of light at a sub-wavelength scale in an extremely compact device. Static single-pixel metasurfaces have addressed multiple needs (focussing, polarization control15, or correcting optics16) or multipixel metasurfaces (next-generation biodevices17). Consequently, an ideal platform for high-speed SLMs combines high-performance χ(2) materials with nanostructures. Current demonstrations of monolithic metasurfaces from χ(2) materials typically trade off an operation around a sharp resonance in materials with moderate but broadband χ(2) effect e.g., in lithium niobate18,19 or colloidal nonlinear nanocubes20 against an efficient χ(2) effect in application-specific engineered III–V heterostructures, which is however narrowband and located around its bandgap6. While many demonstrations are single-pixel, few exciting multifunctional metasurfaces with multiple electronic controls have emerged experimentally6,21,22 and theoretically23. Important to mention are also metasurfaces based on transparent conductive oxides22,24,25,26 that have enabled SLMs recently27, gate-tunable low-dimensional materials28 or phase change materials such as e.g., GST29,30,31,32,33 that are excellent candidates in scenarios, where high switching speeds are not required. Microelectromechanical34,35 or thermo-optically controlled36 systems are ideal for low speed applications that do not require pixel-level control.
Custom-engineered organic nonlinear molecules instead overcome this bandwidth-nonlinearity limitation since they have electro-optic coefficients that are 10–100 times higher than standard materials (up to r33 = 560 pmV−1 in bulk layers and 200 pmV−1 in nanoplasmonic gaps of gold electrodes37), over the entire band from 1100 to 1600 nm (see Supplementary Note 7). They are anticipated to deliver high-end SLMs, owing to their terahertz-compatible bandwidth (up to 2.5 THz38), high index of refraction and recently reported long-term thermal and chemical stability39. Only little work studies such molecules beyond silicon photonic circuits (where they reach highest electro-optic couplings4 and integration with complementary metal-oxide-semiconductor (CMOS) electronics40) for large-area electro-optic modulators, even in the single pixel case41,42. The only SLMs demonstrated so far to the best of our knowledge employ vertical Fabry-Perot geometries that do not exploit nano-engineering, and force an operation with the much lower r13 electro-optic coefficient43.
In this work, we experimentally demonstrate that a single layer of organic non-linear material (here JRD1 mixed with PMMA) enables custom-tailored engineering of each pixel of an SLM while, at the same time, providing a high modulation efficiency through r33, compatibility with broadband lasers, linearity to driving voltage, low power consumption, and high speed. This stems from our ability to manipulate the tensorial properties of the nonlinearity (magnitude and orientation) of the thin film at the nanoscale at will by electric field poling44, and influence the electric current per pixel by mixing of JRD1 with PMMA.
Results
Electro-optic spatial light modulator concept
The proposed device is depicted in Fig. 1 and is utilized to realize single-color or multicolor SLMs at high rates and achieve remote sensing by encoding space information onto the radio-frequency domain. An array of free-space electro-optic modulators controls the transmission of an incident beam in the transverse plane. Each electro-optic modulator exhibits a resonance, around which the transmission changes dramatically. Being covered by a single layer of organic electro-optic molecules, the resonant wavelength of each modulator shifts under an applied driving voltage via the r33 component of the Pockels effect (see inset for behavior around the operation wavelength λop as a function of voltage). A single electro-optic modulator is explained in Fig. 2a and fabricated devices are shown in Supplementary Fig. 12: metallic stripes of total thickness hAu from titanium and gold (of thickness 15 nm and 25/35 nm, respectively and width 200 nm, see scanning electron micrograph in Supplementary Fig. 12c) are assembled into a linear array and covered by a film of organic electro-optic molecules JRD1 mixed with PMMA with 50 wt% (represented in green in Fig. 2a and shown in the photo in Supplementary Fig. 12b and the bright field image in Supplementary Fig. 12d). The film is cast post-fabrication, at which point it is not active yet. The interdigitated metallic array serves three distinct purposes: 1. it is used to render the organic thin film electro-optically active by a poling procedure during which the orientation of the organic molecules (and thereby their electro-optic coefficient r33) is oriented, at the nanoscale, along an applied DC electric field, owing to their hyperpolarizability, 2. it sustains the generation of guided mode resonances45 that introduce a voltage-dependent transmission of the incident beam, and 3. it is used post-activation as contacts for the RF drives of the modulators.
The organic film is poled in-plane44, shown in the upper inset of Fig. 2a. Adjacent unit cells of the array are poled in anti-parallel directions, yielding an in-plane periodically poled (PP) JRD1:PMMA film (in-plane PP-JRD1:PMMA) with alternating electro-optic coefficients r33 (blue) and −r33 (red). Consequently, all unit cells exhibit the same refractive index change \({{\Delta }}n(t)=-\frac{1}{2}{n}_{{{{{{{{\rm{mat}}}}}}}}}^{3}{r}_{33}{E}_{{{{{{{{\rm{AC}}}}}}}}}(t)\) (see lower inset of Fig. 2a, marked green), which depends linearly on the tuning voltage VAC applied to the contacts \({E}_{{{{{{{{\rm{AC}}}}}}}}}(t)=\frac{{V}_{{{{{{{{\rm{AC}}}}}}}}}(t)}{{w}_{{{{{{{{\rm{gap}}}}}}}}}}\). nmat is the material refractive index at the wavelength of the resonant mode (see Fig. 2b). A change in topography is observed after poling, see dark field and atomic force microscopy in Supplementary Fig. 12e, f. The characteristic current–voltage (I–V) curve of the modulator is shown Fig. 2d up to bias fields similar to poling fields, around of 100 V μm−1. The device exhibits the characteristics of a metal-semiconductor-metal junction. Consequently, the tunneling current of one pixel is typically below 100 nA, even for a total modulator area of lel × lel = 390 μm × 390 μm. Details on the electronic structure of JRD1 can be found for example in Ref. 46. The available tuning range spans from −Epol to +Epol. For our study, we purposefully chose large pixel arrays, as opposed to small pixels, in order to demonstrate both the low electric power consumption below 10 μW (corresponding to electrical switching energies below 10 pJ at 1 μs), and the ability to activate at once and drive in parallel millimeter-sized SLMs using a single JRD1:PMMA layer.
Resonance engineering
The optical guided mode resonances (see Fig. 2c) arise through the interplay between the metallic array and the layer of JRD1:PMMA45 with dielectric properties as shown in Fig. 2b. The full refractive index data is provided for various concentrations of the JRD1:PMMA compound in the Supplementary Note 6 and in the data associated with this manuscript. In short, an incident beam is diffracted by the array into grating orders, which correspond, at given angles, to guided modes in the slab formed by JRD1:PMMA of hJRD1 = 690 nm and surrounded by air above and quartz below. Owing to reciprocity, the grating also scatters the guided light back which interferes with the incident light to create well-defined resonances. In both experiment and simulation, we vary the periodicity of the array wfield between 0.8 and 1.4 μm and target three different guided mode resonances of different in-plane wavevectors kz (I., II., and III.) in Fig. 2f which have typical field distributions with corresponding real part of their x-component and z-component as shown in Fig. 2g. Their linewidth increases with increasing thickness of the metal (see Supplementary Note. 4A). Their optical field overlaps well with the simulated DC field distribution between the two electrodes as plotted in Fig. 2e, which governs the orientation of the r33 component. We note that as a result of the spatially varying magnitude and orientation of the poling field, the electro-optic coefficient r33 and the refractive index change Δn also vary spatially. A detailed discussion is provided in the Supplementary Note 3. We probe the optical properties of the modulators by shining a focused beam of light from a supercontinuum laser (SuperK Select) polarized in the z-direction. We record the transmission as a function of wavelength and find that our simulations reproduce well the wavelength dependence of the resonances, reported in Fig. 2f. We find that for wavelengths close to 1100 nm, the high loss of the JRD1:PMMA (see ϵi in Fig. 2b) broadens the resonances and limits their depth. We note that the broad bandwidth of the probe light (5–10 nm, shown in Supplementary Note 4D), combined with its focussing onto the sample using a lens of focal length f = 60 mm, obscure the real linewidth in measurements. The resonant wavelength shifts linearly with driving voltage:
where \({\lambda }_{{{{{{{{\rm{res}}}}}}}}}\) is the resonant frequency, Γc is the overlap factor between the optical mode, the applied DC or RF mode, and the nonlinear material. A full derivation of the non-linear interaction and the definition of the overlap factor are given in the Supplementary Note 1 and 2. We quantify the performance of our intensity modulators by their modulation strength η
where TV is the transmission through the modulator at given actuating voltage and T0 the transmission at 0 V. \({\eta }_{\max }\) is the maximum modulation for a given device.
DC tuning
First, we report the tuning behavior of our modulators upon an applied DC bias VDC using the setup shown in Fig. 3a and described in the “Methods” section. We report in Fig. 3b–d the measured tuning of the resonance for mode I. at wfield = 0.9 μm, which exhibits an overlap factor of Γc = 0.25. We extract a maximal tuning of the resonant frequency by \({{\Delta }}{\lambda }_{{{{{{{{\rm{res}}}}}}}}}=11\) nm over a voltage swing from +80 V to −80 V, and a maximal modulation of \({\eta }_{\max }=37\, \%\). From these results, we estimate an in-device value of r33 = 105 pmV−1. In more detail, mode I. splits into two slightly offset modes I. and I.’ due to an incident angle that slightly deviates from θ = 0°. In the Supplementary Note 4B, we show by experiment and simulations how the optical response changes with incident angle. The resonant wavelengths of these two frequencies (shown in green and purple) are represented as a function of tuning voltage in Fig. 3d, and exhibit clear tuning when compared to the resonant wavelength at VDC = 0 V (shown in red). In Fig. 3e–g we analyse the tuning behavior of the same transmission curves as a time-series, where in each iteration the applied DC voltage is changed according to the stars in Fig. 3f in the order indicated by the arrow. When tracking the resonant wavelength of the modulator in Fig. 3g, we find that it depends linearly on the applied voltage and that even after applying fields as high as ±80 V, the modulator goes back to its transmission at 0 V after the voltage is disconnected.
RF tuning
Now we discuss the performance of our devices at radio frequencies \({f}_{{{{{{{{\rm{mod}}}}}}}}}\), up to 50 MHz. We drive the modulators with an RF source (pulser Agilent 8114A, maximal frequency 50 MHz) and demodulate the transmitted intensity at the modulation frequency of the pulses, as shown in Fig. 4. We demonstrate the broadband character of the Pockels effect in the organic material exemplarily at three chosen resonances, dictated primarily by the periodicity of the interdigitated array, that span from 1100 to 1500 nm, shown in Fig. 4b (at 1480 nm, mode I. for wfield = 1 μm), c (at 1160 nm, mode II. for wfield = 1 μm, Γc = 0.3) and d (at 1350 nm, mode II. for wfield = 0.9 μm, Γc = 0.25). The pulse scheme consists of an overall DC voltage offset Vo, and an additional RF voltage with Vpeak = 2Vo, as shown in the inset of Fig. 4a. In Fig. 4e we report an exemplary wavelength-resolved modulation curve for Vpeak = [−80 V, 80 V] at a modulation frequency \({f}_{{{{{{{{\rm{mod}}}}}}}}}=100\) kHz, while operating around the resonances shown in Fig. 4b. We observe a low-noise modulation (its maximum value is marked with the vertical dashed marker), which switches sign around the resonant wavelength and is strongest where the slope in the transmission curve is highest, as expected. Moreover, it flips sign when switching the polarity of the applied modulation voltage, as expected from the exploited Pockels effect, which is linear in field amplitude. From the modulation data, we plot the maximal modulation strength \({\eta }_{\max }\) for wfield = 1 μm in Fig. 4f, g, and for wfield = 0.9 μm in Fig. 4h, respectively. For the resonances at 1480 nm, 1350 nm and 1160 nm we report a maximum modulation of \({\eta }_{\max }=38 \%\), 28% and 40%, respectively. We demonstrate experimentally that a 2 × 2 SLM device can be operated up to a frequency of \({f}_{{{{{{{{\rm{mod}}}}}}}}}=50\) MHz where a 3-dB decay of the modulation is observed, marked by the full circles in Fig. 4i. In the Supplementary Note 4F, we provide extensive optical and electronic measurements that show how a series resistance influences the cut-off frequency of the pulser-cable-sample system. Additionally, we derive a simple low-frequency equivalent circuit model loaded with an external resistor for the pulser-cable-sample system, marked by empty circles in Fig. 4i. We note that for operation at frequencies beyond the ones discussed here, this model is inappropriate and a high-frequency transmission line model that accounts also for the cable line inductance is necessary. Finally, we experimentally quantify thermo-optic tuning effects and show that their contribution is negligible as compared to the electro-optic effect in the Supplementary Note 4C.
Single-color and multicolor SLMs
In the following we combine several modulators into arrays: in a first example discussed here four of equal periodicity (wfield = 1.4 μm) into a 4-pixel array, which features a total active area of 780 × 780 μm2. All pixels are poled in parallel at once in one single run, using the voltage configuration of Fig. 5a. For remote control, each pixel is instead contacted individually (voltages V1 to V4), as shown in Fig. 5b. A large area incident beam has a central emission wavelength of λ = 1154 nm, and operates at the high-sensitivity working point marked in Fig. 5c, with a maximum \({\eta }_{\max }=22 \%\) and a resonant wavelength tuning of \({{\Delta }}{\lambda }_{{{{{{{{\rm{res}}}}}}}}}=5\) nm over a swing of −40 V to 40 V. The modulated beam is imaged using an indium gallium arsenide (InGaAs) camera at 25 frames per second, limited by the camera. In Fig. 5f–h, we report multiple intensity profiles under different combinations of the actuating voltages V1 to V4 and at eight representative voltage levels, which result into well discernible transmission patterns through the SLM. The depicted intensity profiles have been post-processed by subtracting the transmission through the modulator at voltages V1 = V2 = V3 = V4 = 0. From one single pixel in Fig. 5f, we augment to two pixels in Fig. 5g and then four pixels concomitantly actuated pixels in Fig. 5h. The individual pixels exhibit comparable intensity strengths at a fixed voltage, which confirms their homogenous poling, and the straight-forward ability to pole a millimeter area with good uniformity. In the Supplementary Note 4B, we show by experiment and simulations how the optical response changes with incident angle and discuss how this influences the angle of acceptance of the electro-optic modulators, which we find to be ϕ = ±10° and θ = ±1° (see Supplementary Figs. 3 and 4). In a second example shown in the Supplementary Note 5, five pixels of distinct periodicities are assembled into a multi-color SLM. The Supplementary Movie 1 associated with this manuscript demonstrates its operation. It consists of a stack of images that represent the raw intensity modulation measured with the camera, while tuning the laser in resonance with the individual pixels of the multicolor SLM.
Remote sensing by single-pixel imaging
In a second experiment, we use our SLM for remote sensing on parallel channels. The core concept is that the SLM divides a three-dimensional space into n distinct space bins (here n = 4, the number of pixels), as shown in Fig. 6a. By modulating the four pixels at individual frequencies (\({f}_{{{{{{{{\rm{mod}}}}}}}},1}=100\,\) kHz, \({f}_{{{{{{{{\rm{mod}}}}}}}},2}=99\,\) kHz, \({f}_{{{{{{{{\rm{mod}}}}}}}},3}=98\,\) kHz, \({f}_{{{{{{{{\rm{mod}}}}}}}},4}=97\,\) kHz), a one-to-one correspondence is established between the distinct space bins and their associated radio frequency (Fig. 6b). The beam then traverses a space that is monitored and is subsequently detected at a single pixel high-speed InGaAs photodiode (the collection lens has a focal length of 60 mm). As a result of the transfer of information from the spatial to the RF domain, a deconvolution of the individual modulation frequencies and their amplitudes permits to reconstruct a time-resolved or position-resolved image of the transverse plane without the need of a camera28. When a L-shape blank is traversing the modulated beam in the transversal direction, it introduces changes in the intensity of the transmitted light and thereby also of the radio frequencies. The demodulated amplitudes (here measured subsequently, due to the unavailability of four distinct RF sources) are shown in Fig. 6c. In Fig. 6d we show the reconstructed two-dimensional maps of the transmitted beam. The position of the blank is marked by the dotted line and clearly influences the transmission of the individual pixels. Our preliminary demonstration underlines the key characteristics of this measurement scheme, discussed in the “Methods” section.
In conclusion, we have demonstrated a 2 × 2-pixel single-color SLM and a 1 × 5 pixel multicolor SLM, featuring an acceptance angle of ϕ = ±10° and θ = ±1°, which exploits broadband high-performance electro-optic molecules as an active medium to impart an intensity modulation up to 40% to an incident beam at speeds as high as 50 MHz. We deploy the spatial light modulator of total area of 780 × 780 μm2 in two real-life scenarios, for image projection and to remotely probe the environment on parallel channels. The unique properties of the organic film, including the ability to engineer its nonlinearity at will, at the nanoscale, its compatibility with broad resonances (and thereby broadband lasers), and its high-speed could open long-anticipated applications that benefit from—or require—straight-forward up-scaling, simple fabrication and low power consumption: imaging, virtual reality, laser ranging, and sensing. While further studies are needed to push the modulation speed of free-space modulators towards the microwaves and terahertz, the hybrid organic electro-optic integration with multipixel nanophotonic technology demonstrated here already shows a path to create more efficient, faster and more customized SLMs. Finally, brand-new organic electro-optic materials HLD1:HLD2 have been reported recently to have excellent temperature and chemical resilience in long-term aging tests39, thereby overcoming any remaining issues for organic electro-optic materials to be deployed into a much greater variety of instrumentation at large scales.
Methods
Sample fabrication and electric field poling of the devices
The free-space modulators were fabricated on 1 mm thick quartz substrates by electron beam lithography (ZEP520A) and subsequent electron beam evaporation of a metallic wires of thickness 15 nm titanium and 25/35 nm gold and width wAu = 200 nm. After lift-off, the samples were coated by the JRD1:PMMA mixture which had been prepared beforehand. A 50%wt mixture of JRD1 powder and PMMA in solid form was first mixed with 1,1,2-trichlorethane (5% wt) for 8 h in a swirling machine. Afterwards, the solution was filtered using 0.2 μm PTFE-filters before being deposited on-chip by spin-coating at 1000 rpm. After coating, the film was dried in a vacuum oven at 85 °C for 24 h. After drying, a semitransparent, clean and homogenous film of 690 nm thickness was measured on the final samples. The electric field poling of the organic film was then performed inside a DC probe station under vacuum. All samples were first characterized regarding their typical IV-curves, which all exhibited the typical diode-like characteristics shown in the main text. A poling field of typically 100 V μm−1 (below the breakdown field of the material) was applied to the interdigitated electrodes, which were heated above glass temperature 97 °C. The poling field was kept for typically 10 min at poling temperature, after which the samples were cooled down to room temperature. Finally, poled samples were inspected both in bright and dark field microscopy, as well as using atomic force microscopy. As shown, the film changes conformation quite significantly, which can be used as an indication of efficient poling. In the case of the multipixel SLMs, all pixels are contacted in parallel prior to electric field poling by wire bonding. Consequently, during the poling procedure, all pixels of one single SLM experience the same poling field and the nonlinearity in all pixels is established in one single run. Given this activation procedure, it is essential that all pixels feature comparable internal resistances.
Experimental setup
A DC/AC voltage is applied to one contact of the modulator, while the other contact is grounded. A slow (DET20C2) or fast (FPD310-FS-NIR) photodiode monitors the transmitted power. For the RF measurements, we use a RF pulsed source to drive the modulators up to 50 MHz and a Zurich Instruments RF lock-in amplifier (MFLI, 5 MHz and UHFLI, 600 MHz) to demodulate the transmitted intensity at the modulation frequency of the pulses. We use a tunable laser (super-K Select) to probe the modulation characteristics of our modulators. Its linewidth is described in detail in Fig. 4 of the Supplementary Information, and exceeds 4 nm and can range up to 11.5 nm. The ability of our modulators to introduce significant intensity modulation even to a broadband incident beam are an experimental proof that the modulators are—in principle—compatible with compact laser diodes, which have relatively broad linewidths. Even more, they can accommodate wavelength tolerances in the fabrication of laser diodes which are typically up to 10 nm (e.g., Eblana Photonics EP1310-ADF-B laser diode). This property outperforms typical demonstrations of electro-optic free-space transducers which trade a very specific and narrow operation point for high intensity/phase tuning properties.
Relationship between channels and integration time in remote sensing
The frequency resolution of the individual channels is given by \(\delta f=\frac{1}{{t}_{{{{{{{{\rm{int}}}}}}}}}}\), where tint is the total integration time per pixel. A resolution around 0.1 kHz requires 10 ms integration time and is sufficient to resolve modulation frequencies spaced by 1 kHz. In our case, the demonstrated modulation bandwidth up to 50 MHz would accommodate—in principle—the modulation frequencies of 50,000 pixels. However, having the ability to modulate the individual pixels at speeds up to the terahertz not only allows to increase the number of pixels but also to reduce the integration time per pixel, by spacing them further apart in the RF domain.
Data availability
The main dataset contained within this paper, as well as the material parameters of JRD1:PMMA depicted in Supplementary Fig S10 and 11 are available in the Zenodo database at https://doi.org/10.5281/zenodo.5140234.
Code availability
The code used to plot the data within this paper is available in the Zenodo database at https://doi.org/10.5281/zenodo.5140234.
References
Wang, C. et al. Integrated lithium niobate electro-optic modulators operating at CMOS-compatible voltages. Nature 562, 101–104 (2018).
Abel, S. et al. Large pockels effect in micro- and nanostructured barium titanate integrated on silicon. Nat. Mater. 18, 42–47 (2019).
Haffner, C. et al. All-plasmonic Mach-Zehnder modulator enabling optical high-speed communication at the microscale. Nat. Photonics 9, 525–528 (2015).
Benea-Chelmus, I.-C. et al. Electro-optic interface for ultrasensitive intracavity electric field measurements at microwave and terahertz frequencies. Optica 7, 498–505 (2020).
Benea-Chelmus, I.-C., Settembrini, F. F., Scalari, G. & Faist, J. Electric field correlation measurements on the electromagnetic vacuum state. Nature 568, 202–206 (2019).
Wu, P. C. et al. Dynamic beam steering with all-dielectric electro-optic III-V multiple-quantum-well metasurfaces. Nat. Commun. 10, 3654 (2019).
Fan, L. et al. Superconducting cavity electro-optics: a platform for coherent photon conversion between superconducting and photonic circuits. Sci. Adv. 4, 4994 (2018).
Riemensberger, J. et al. Massively parallel coherent laser ranging using a soliton microcomb. Nature 581, 164–170 (2020).
Barredo, D., de Léséleuc, S., Lienhard, V., Lahaye, T. & Browaeys, A. An atom-by-atom assembler of defect-free arbitrary two-dimensional atomic arrays. Science 354, 1021–1023 (2016).
Schwarz, B. Mapping the world in 3D. Nat. Photonics 4, 429–430 (2010).
Dudley, D., Duncan, W., & Slaughter, J. Emerging Digital micromirror device (DMD) applications. DLPTM Products New Appl. 4985, 14–23 (2003).
Hu, L. et al. Phase-only liquid-crystal spatial light modulator for wave-front correction with high precision. Opt. Express 12, 6403–6409 (2004).
Smolyaninov, A., El Amili, A., Vallini, F., Pappert, S. & Fainman, Y. Programmable plasmonic phase modulation of free-space wavefronts at gigahertz rates. Nat. Photonics 13, 431–435 (2019).
Khorasaninejad, M. & Capasso, F. Metalenses: versatile multifunctional photonic components. Science 358, eaam8100 (2017).
Balthasar Mueller, J. P., Rubin, N. A., Devlin, R. C., Groever, B. & Capasso, F. Metasurface polarization optics: independent phase control of arbitrary orthogonal states of polarization. Phys. Rev. Lett. 118, 113901 (2017).
Chen, W. T., Zhu, A. Y. & Capasso, F. Flat optics with dispersion-engineered metasurfaces. Nat. Rev. Mater. 5, 604–620 (2020).
Tittl, A. et al. Imaging-based molecular barcoding with pixelated dielectric metasurfaces. Science 360, 1105–1109 (2018).
Gao, B. et al. Lithium niobate metasurfaces. Laser Photonics Rev. 13, 1800312 (2019).
Weigand, H. et al. Enhanced electro-optic modulation in resonant metasurfaces of lithium niobate. https://arXiv.org/2106.12232v2.
Karvounis, A. et al. Electro-optic metasurfaces based on barium titanate nanoparticle films. Adv. Optical Mater. 8, 2000623 (2020).
Li, S.-Q. et al. Phase-only transmissive spatial light modulator based on tunable dielectric metasurface. Science 364, 1087–1090 (2019).
Shirmanesh, G. K., Sokhoyan, R., Wu, P. C. & Atwater, H. A. Electro-optically tunable multifunctional metasurfaces. ACS Nano 14, 6912–6920 (2020).
Peng, C., Hamerly, R., Soltani, M. & Englund, D. R. Design of high-speed phase-only spatial light modulators with two-dimensional tunable microcavity arrays. Opt. Express 27, 30669–30680 (2019).
Forouzmand, A., Salary, M. M., Inampudi, S. & Mosallaei, H. A tunable multigate indium-tin-oxide-assisted all-dielectric metasurface. Adv. Optical Mater. 6, 1701275 (2018).
Huang, Y.-W. et al. Gate-tunable conducting oxide metasurfaces. Nano Lett. 16, 5319–5325 (2016).
Reshef, O., De Leon, I., Alam, M. Z. & Boyd, R. W. Nonlinear optical effects in epsilon-near-zero media. Nat. Rev. Mater. 4, 535–551 (2019).
Park, J. et al. All-solid-state spatial light modulator with independent phase and amplitude control for three-dimensional LiDAR applications. Nat. Nanotechnol. https://doi.org/10.1038/s41565-020-00787-y (2020).
Zeng, B. et al. Hybrid graphene metasurfaces for high-speed mid-infrared light modulation and single-pixel imaging. Light Sci. Appl. 7, 51 (2018).
Abdollahramezani, S. et al. Tunable nanophotonics enabled by chalcogenide phase-change materials. Nanophotonics 9, 1189–1241 (2020).
Michel, A.-K. U. et al. Optical properties of amorphous and crystalline GeTe nanoparticle thin films: a phase-change material for tunable photonics. ACS Appl. Nano Mater. 3, 4314–4320 (2020).
Chaudhary, K. et al. Polariton nanophotonics using phase-change materials. Nat. Commun. 10, 4487 (2019).
Leitis, A. et al. All-dielectric programmable Huygens’ metasurfaces. Adv. Funct. Mater. 30, 1910259 (2020).
Wang, Q. et al. Optically reconfigurable metasurfaces and photonic devices based on phase change materials. Nat. Photonics 10, 60–65 (2016).
Arbabi, E. et al. MEMS-tunable dielectric metasurface lens. Nat. Commun. 9, 812 (2018).
She, A., Zhang, S., Shian, S., Clarke, D. R. & Capasso, F. Adaptive metalenses with simultaneous electrical control of focal length, astigmatism, and shift. Sci. Adv. 4, eaap9957 (2018).
Berto, P. et al. Tunable and free-form planar optics. Nat. Photonics 13, 649–656 (2019).
Heni, W. et al. Nonlinearities of organic electro-optic materials in nanoscale slots and implications for the optimum modulator design. Opt. Express 25, 2627–2653 (2017).
Salamin, Y. et al. Compact and ultra-efficient broadband plasmonic terahertz field detector. Nat. Commun. 10, 5550 (2019).
Xu, H. et al. Ultrahigh electro-optic coefficients, high index of refraction, and long-term stability from Diels-Alder cross-linkable binary molecular glasses. Chem. Mater. 32, 1408–1421 (2020).
Koch, U. et al. A monolithic bipolar CMOS electronic-plasmonic high-speed transmitter. Nat. Electron. 3, 338–345 (2020).
Zhang, J. et al. Electrical tuning of metal-insulator-metal metasurface with electro-optic polymer. Appl. Phys. Lett. 113, 231102 (2018).
Zhang, J., Kosugi, Y., Otomo, A., Nakano, Y. & Tanemura, T. Active metasurface modulator with electro-optic polymer using bimodal plasmonic resonance. Opt. Express 25, 30304 (2017).
Greenlee, C. et al. Electro-optic polymer spatial light modulator based on a Fabry–Perot interferometer configuration. Opt. Express 19, 12750–12758 (2011).
Dalton, L. R., Sullivan, P. A. & Bale, D. H. Electric field poled organic electro-optic materials: state of the art and future prospects. Chem. Rev. 110, 25–55 (2010).
Wang, S. S. & Magnusson, R. Theory and applications of guided-mode resonance filters. Appl. Opt. 32, 2606–2613 (1993).
Jin, W. et al. Benzocyclobutene barrier layer for suppressing conductance in nonlinear optical devices during electric field poling. Appl. Phys. Lett. 104, 243304 (2014).
Acknowledgements
The authors acknowledge insightful discussions with Stefan Breuer, Christopher Bonzon, Dmitry Kazakov, Daniel Lim, Sydney Mason, Marcus Ossiander, and Noah Rubin, as well as Zurich Instruments who lended the UHFLI. I.-C. Benea-Chelmus acknowledges support through the Swiss National Science Foundation for the postdoctoral fellowship P2EZP2.181935 and an independent research grant from the Hans Eggenberger foundation. M.L. Meretska is supported by NWO Rubicon Grant 019.173EN.010, by the Dutch Funding Agency NWO. D.L. Elder and L.R. Dalton acknowledge support from the Air Force Office of Scientific Research (FA9550-19-1-0069). Additionally, financial support from the Office of Naval Research (ONR) MURI program, under grant no. N00014-20-1-2450 is acknowledged. This work was performed in part at the Harvard University Center for Nanoscale Systems (CNS); a member of the National Nanotechnology Coordinated Infrastructure Network (NNCI), which is supported by the National Science Foundation under NSF award no. ECCS-2025158. The electro-optic molecules were synthesised in the Chemistry Department at the University of Washington.
Author information
Authors and Affiliations
Contributions
I.-C.B.-C. conceived, designed and implemented the experiments and wrote the manuscript with feedback from the other co-authors. I.-C.B.-C, M.M. and M.T. fabricated the samples. I.-C.B.-C. did the theoretical derivations and the simulations. D.E. and L.D. developed the electro-optic molecules, measured the refractive indices and assisted with the poling of the devices. I.-C.B.-C., M.M., M.T., and F.C. analysed the data. All authors gave feedback to the manuscript.
Corresponding authors
Ethics declarations
Competing interests
A provisional patent application with U.S. Serial No.: 63/148,595 has been filed on the subject of this work by the President and Fellows of Harvard College.
Additional information
Peer review information Nature Communications thanks Hyuck Choo and the anonymous reviewer(s) for their contribution to the peer review of this work.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Benea-Chelmus, IC., Meretska, M.L., Elder, D.L. et al. Electro-optic spatial light modulator from an engineered organic layer. Nat Commun 12, 5928 (2021). https://doi.org/10.1038/s41467-021-26035-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-021-26035-y
This article is cited by
-
Dynamic light manipulation via silicon-organic slot metasurfaces
Nature Communications (2024)
-
Large-volume focus control at 10 MHz refresh rate via fast line-scanning amplitude-encoded scattering-assisted holography
Nature Communications (2024)
-
Giant magneto-photoluminescence at ultralow field in organic microcrystal arrays for on-chip optical magnetometer
Nature Communications (2024)
-
Electrical field sensing in an etchless lithium niobate heterostructure with Low driving voltage based on quasi-bound states in the continuum
Indian Journal of Physics (2024)
-
Plasmonic metafibers electro-optic modulators
Light: Science & Applications (2023)