Skip to main content

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

A pyridinic Fe-N4 macrocycle models the active sites in Fe/N-doped carbon electrocatalysts

Subjects

Abstract

Iron- and nitrogen-doped carbon (Fe-N-C) materials are leading candidates to replace platinum catalysts for the oxygen reduction reaction (ORR) in fuel cells; however, their active site structures remain poorly understood. A leading postulate is that the iron-containing active sites exist primarily in a pyridinic Fe-N4 ligation environment, yet, molecular model catalysts generally feature pyrrolic coordination. Herein, we report a molecular pyridinic hexaazacyclophane macrocycle, (phen2N2)Fe, and compare its spectroscopic, electrochemical, and catalytic properties for ORR to a typical Fe-N-C material and prototypical pyrrolic iron macrocycles. N 1s XPS and XAS signatures for (phen2N2)Fe are remarkably similar to those of Fe-N-C. Electrochemical studies reveal that (phen2N2)Fe has a relatively high Fe(III/II) potential with a correlated ORR onset potential within 150 mV of Fe-N-C. Unlike the pyrrolic macrocycles, (phen2N2)Fe displays excellent selectivity for four-electron ORR, comparable to Fe-N-C materials. The aggregate spectroscopic and electrochemical data demonstrate that (phen2N2)Fe is a more effective model of Fe-N-C active sites relative to the pyrrolic iron macrocycles, thereby establishing a new molecular platform that can aid understanding of this important class of catalytic materials.

Introduction

The four-electron, four-proton reduction of molecular oxygen to water is the efficiency-limiting half reaction in low-temperature fuel cells1. Regardless of the fuel source used, the current density output is primarily limited by the slow electron transfer kinetics of the oxygen reduction reaction (ORR) taking place at the cathode2. The prototypical material for catalyzing this reaction in commercial fuel cells is platinum metal (Pt) supported on carbon. However, the high cost and scarcity of Pt impedes the large-scale deployment of fuel cell devices and motivates the development of Earth-abundant electrocatalysts for oxygen reduction. These catalysts must operate at low overpotentials3,4,5 and with high selectivity for the four-electron reduction of oxygen to water instead of the two-electron reduction process to generate hydrogen peroxide6,7,8,9. Since early reports of oxygen reduction catalyzed by macrocyclic first-row transition metal complexes10,11, there has been a global effort to develop selective and efficient ORR catalysts featuring base metal active sites12.

Pyrolyzed iron- and nitrogen-doped (Fe-N-C) materials are leading Earth-abundant alternatives to Pt-based ORR electrocatalysts13, however marked increases in catalyst performance are needed to make these materials technologically viable. Recent years have witnessed significant improvements in their performance14, however systematic development of these materials is hampered by limited molecular-level understanding or control of the iron active sites15. Fe-N-C materials are typically prepared by the high-temperature pyrolysis of finely dispersed iron salts16, porphyrins17, or phthalocyanines18 along with a metal-organic framework (MOF)19 or carbon-based support20. The uncontrolled nature of pyrolysis leads to a wide diversity of iron environments as well as extended solid iron phases in the resulting Fe-N-C materials21,22. This poor control, combined with the wide variability in preparative procedures, has led to longstanding uncertainty about the local structure of the iron active sites responsible for ORR, thereby impeding systematic enhancements to catalytic performance23.

Numerous recent studies have provided significant insight into possible Fe-N-C active site structures. While metallic iron active sites have been postulated24,25, mononuclear Fe-N4 active sites are more commonly invoked to explain correlations between X-ray absorption spectroscopy (XAS) or 57Fe Mössbauer spectroscopy with ORR activity16. Despite the growing consensus that Fe-N4 sites are essential for ORR, the ligation environment of these iron sites remains uncertain26,27. Indeed, even though iron porphyrin and phthalocyanine complexes can be used as precursors to Fe-N-C materials, there is evidence that the core pyrrolic ligation environment of these precursors changes substantially upon pyrolysis28,29,30,31. In particular, the first shell Fe–N bond lengths in Fe-N-C materials have been reported to be shorter than the macrocyclic iron complex precursor used in the material synthesis17. Furthermore, X-ray photoelectron spectroscopy (XPS) results have pointed to the presence of metal-coordinated pyridinic nitrogen moieties as opposed to metal-bound pyrrolic nitrogens in Fe-N-C materials32. 57Fe Mössbauer spectra of many iron porphyrin33 and phthalocyanine34 complexes differ dramatically from the main 57Fe Mössbauer doublets assigned to the putative Fe-N4 active sites in Fe-N-C materials35,36,37. In addition, atomic-resolution electron microscopy data indicate the presence of mono-dispersed iron atoms bound within the plane of graphitic carbon38,39,40,41,42 suggesting that the ligating groups are six-membered heterocycles rather than the five-membered rings found in pyrrolic macrocycles. Based on these spectroscopic and imaging results, there is a growing body of evidence that the Fe-N4 sites in Fe-N-C materials are ligated by pyridinic moieties fused within graphitic sheets (Fig. 1a).

Fig. 1: Putative Fe-N4 ORR active site and molecular model structures.
figure 1

Proposed Fe-N4 active site in Fe-N-C materials (a). Molecular structures of (Pc)Fe and (OEP)Fe (b) and (phen2N2)Fe (c) model compounds.

Despite substantial evidence for pyridinic Fe-N4 sites in Fe-N-C materials, nearly all molecular Fe-based ORR catalysts that are used to model the iron-containing active sites of Fe-N-C are macrocyclic complexes that feature pyrrolic coordination environments (Fig. 1b). Notwithstanding evident differences between the spectroscopic features of Fe-N-C and pyrrolic-type macrocycles, such macrocyclic complexes are routinely used as models during the analysis of X-ray absorption data to build computational fits to the experimental Fe-N-C data in order to construct toy models of the apparent Fe-N4 sites. Such an approach could be strengthened by the creation of a pyridinic Fe-N4 model architecture that is better able to model the average Fe-N4 sites in Fe-N-C relative to pyrrolic iron complexes. Owing to the inherent multi-scale complexity of Fe-N-C materials, no molecular complex will ever be able to perfectly reproduce their spectroscopic signatures or catalytic function. Pyrrolic model compounds have offered valuable spectroscopic and mechanistic insights and such molecular-level studies would benefit from new model complexes that feature the pyridinic ligation motifs that are now thought to exist in Fe-N-C materials.

Based on the aggregate spectroscopic evidence on Fe-N-C materials, we envisioned that an improved model complex would feature: (a) a tetrapyridinic coordination environment, (b) relatively short Fe–N bond lengths17, (c) an extended ligand π system29,30 capable of stabilizing the Fe(II) state43,44, and (d) a relatively high Fe(III)-OH/Fe(II)-OH2 redox potential. Towards realizing the above goal of synthesizing a pyridinic Fe-N4 model complex, we searched the literature for pyridinic N4 macrocyclic ligands. Notably, the aza-bridged bis-1,10-phenanthroline hexaazamacrocycle, (phen2N2)H2 (phen2N2 = 1,14:7,8-diethenotetrapyrido[2,1,6-de:2′,1′,6′-gh:2″,1″,6″-kl:2″′,l″′,6″′-na][1,3,5,8,10,12]hexaazacyclotetradecine), as well as its cobalt(II), nickel(II) and copper(II) complexes have been reported45 and applied to DNA binding studies46 and carbon dioxide reduction catalysis47. Despite this precedent, the synthesis and ORR activity of the corresponding (phen2N2)Fe fragment44 has, to the best of our knowledge, remained unexplored.

Herein, we report the synthesis and characterization of this pyridinic Fe-N4 macrocyclic fragment (Fig. 1c) and compare its 57Fe Mössbauer, XPS, and XAS features and ORR performance to those of prototypical Fe-N-C, iron octaethylporphyrin, (OEP)Fe, and iron phthalocyanine, (Pc)Fe, catalysts. Through these studies, we demonstrate that the iron coordination environment in [(phen2N2)Fe]2O displays greater spectroscopic similarity to Fe-N-C materials than [(OEP)Fe]2O and [(Pc)Fe]2O. Furthermore, we find that (phen2N2)FeCl displays superior catalytic activity and selectivity relative to (OEP)FeCl and (Pc)FeCl, approaching the performance metrics of Fe-N-C materials. These studies establish (phen2N2)Fe complexes as better structural and functional mimics of Fe-N4 active sites in Fe-N-C materials than legacy pyrrolic macrocycles.

Results and discussion

Synthesis of Fe-N-C and (phen2N2)Fe complexes

A prototypical Fe-N-C material was synthesized by a combination of literature methods19,48. In brief, Fe-N-C was prepared by pyrolysis of a mixture of iron(II) acetate, 1,10-phenanthroline, and a zinc imidazolate MOF (ZIF-8) under a reducing atmosphere (5% H2 in Ar). After pyrolysis, the sample was washed with 0.1 M H2SO4 to remove trace Fe(0). The 57Fe Mössbauer spectrum of this material (Supplementary Fig. 1, top and Supplementary Table 1) displays two quadrupole doublets in line with previously reported Fe-N-C materials.

The bis-phenanthroline macrocycle, (phen2N2)H249, was prepared by exposure of 2,9-dichlorophenanthroline (Supplementary Fig. 2) to anhydrous ammonia in a Parr reactor that was held at 280 °C for 24 h and then ramped to 300 °C for 12 h (Fig. 2). Metalation with iron was achieved by treating (phen2N2)H2 with anhydrous FeCl3 in DMF or HMPA in the presence of excess tributylamine under an N2 atmosphere. To remove unreacted FeCl3 and other reaction byproducts, the crude reaction mixture was washed with copious amounts of diethyl ether and dichloromethane. Due to the extremely low solubility of the (phen2N2)FeCl complex, we found that residual Fe2Cl6•(DMF)3 (~16%) remained in the sample despite exhaustive washing with anhydrous solvents50. HR-MS analysis of the material reveals a prominent peak at 440.1061 m/z and a smaller peak at 475.1023 m/z, in line with the expected masses of [(phen2N2)Fe]+ (440.0473 m/z) and [(phen2N2)FeCl]+ (475.0161 m/z), respectively. UV–Vis data also support formation of the metalated complex with a bathochromic shift of the ligand π → π* transitions and the appearance of shoulders on the main π → π* peak (Supplementary Fig. 3). The 57Fe Mössbauer spectrum of (phen2N2)FeCl (Supplementary Fig. 1, middle and Supplementary Table 2) reveals a broad quadrupole doublet assigned to (phen2N2)FeCl in the S = 3/2 state51,52,53,54, which differs dramatically from the parameters for (OEP)FeCl and (Pc)FeCl (Supplementary Figs. 4 and 5 and Supplementary Table 2). This assignment is consistent with our calculations on (phen2N2)FeCl, which predict an intermediate-spin ground state and is consistent with a compressed N4-binding pocket that stabilizes the S = 3/2 spin state (see Supplementary Note 1 for calculated energies and geometries).

Fig. 2: Syntheses of (phen2N2)H2, (phen2N2)FeCl, and [(phen2N2)Fe]2O.
figure 2

The (phen2N2)H2 macrocycle was synthesized by the reaction of 2,9-dichloro-1,10-phenanthroline with anhydrous ammonia. The (phen2N2)FeCl model complex was obtained by treatment of (phen2N2)H2 with FeCl3 in the presence of N(n-Bu)3 under an inert atmosphere. Continuously washing (phen2N2)FeCl with hot ethanol for 48 hours using a Soxhlet apparatus yielded the [(phen2N2)Fe]2O model complex.

To better mimic the axial O-ligation present in the material, we Soxhleted the (phen2N2)FeCl sample with ethanol. This served to generate the μ-oxo [(phen2N2)Fe]2O via reaction with adventitious water and base. Similar conversions are precedented for sterically unprotected porphyrin complexes55. While this species is catalytically inactive in the acidic electrolyte (Supplementary Fig. 6)56,57, it provides a good spectroscopic model for Fe-N-C materials and the analogous [(OEP)Fe]2O and [(Pc)Fe]2O were synthesized for comparison55,58,59. The 57Fe Mössbauer spectrum of the [(phen2N2)Fe]2O complex is a narrow doublet (Supplementary Fig. 1, bottom and Supplementary Table 2), distinct from the spectra of [(OEP)Fe]2O and [(Pc)Fe]2O (Supplementary Figs. 7 and 8 and Supplementary Table 2). The vast differences in the 57Fe Mössbauer spectra of (phen2N2)Fe, (OEP)Fe, and (Pc)Fe upon exchange of the axial ligand suggest that 57Fe Mössbauer spectroscopy alone may be insufficient to distinguish pyrrolic from pyridinic ligation at putative Fe-N4 sites in Fe-N-C materials.

XPS reveals nitrogen and iron environments similar to Fe-N-C

The nitrogen environments present in Fe-N-C, [(phen2N2)Fe]2O, (phen2N2)H2, [(Pc)Fe]2O, and [(OEP)Fe]2O were analyzed by XPS (see Supplementary Figs. 9 and 10 for XPS survey spectra of all compounds and Supplementary Tables 35 for N:Fe ratios of all samples, component decomposition of the N 1s manifold for Fe-N-C, and N 1s peaks, assignments, and parameters for all samples). For Fe-N-C, we observed a broad N 1s XPS signal similar to that reported for other Fe-N-C materials (Fig. 3a). The N peak envelope for Fe-N-C spans 396–407 eV and can be deconvoluted into four peaks, previously assigned to oxidized (404.0 eV), graphitic/pyrrolic (401.3 eV), metal-coordinated (399.9 eV), and pyridinic nitrogen (398.3 eV)60,61. We note that since this sample was prepared by the pyrolysis of ZIF-8, we expect the metal-coordinated N peak to result from both iron and zinc coordination. Notably, comparing N 1s XPS binding energies for ZnII porphyrins62 and FeIII porphyrins (Fig. 3d and Supplementary Fig. 11) reveal N XPS peaks within 0.2 eV, suggesting that residual Zn does not dramatically convolute the N XPS envelope of this Fe-N-C preparation.

Fig. 3: High-resolution N 1 s and Fe 2p XPS spectra.
figure 3

Fe-N-C (a and e), [(phen2N2)Fe]2O (b and f), [(Pc)Fe]2O (c and g), and [(OEP)Fe]2O (d and h). In the N 1s spectra, pyridinic and bridging nitrogens are depicted in blue, metal-coordinated nitrogens are depicted in magenta, graphitic/pyrrolic nitrogens are depicted as yellow, oxidized nitrogens are shown in purple and the π–π* satellites are shown in dark cyan. In the Fe 2p spectra, the 2p3/2 Fe(II) peak is shown in blue and the 2p3/2 Fe(III) peak is given in magenta. The Fe 2p1/2 peak is given in aqua blue. Multiplet peaks for the 2p3/2 and 2p1/2 peaks are given in green and dark cyan, respectively.

The broad peak envelope for Fe-N-C contrasts with the well-defined nitrogen environments in [(Pc)Fe]2O, [(OEP)Fe]2O, and [(phen2N2)Fe]2O. For [(phen2N2)Fe]2O, high-resolution N 1s spectra (Fig. 3b) reveal a single peak centered at 399.3 eV that can be deconvoluted into two components centered at 398.3 and 399.6 eV with a ratio of peak area values of 1:2. Based on the integration ratio and the symmetry of the (phen2N2)Fe subunits in [(phen2N2)Fe]2O, we assign the 398.3 peak to the bridgehead nitrogens and the 399.6 peak to the coordinated pyridinic nitrogens. In comparison, the N 1s XPS spectrum (Supplementary Fig. 12, bottom) of (phen2N2)H2 is dominated by two peaks corresponding to bridging and pyridinic nitrogen atoms at 397.9 and 399.5 eV, respectively, in a 1:2 ratio. This indicates that both bridging and pyridinic nitrogen atoms shift to higher binding energies upon metalation with iron. Similar changes in the N 1s spectrum have been reported for free-base porphyrins upon metalation63. In contrast, the XPS N 1s spectra of [(Pc)Fe]2O and [(OEP)Fe]2O differ markedly from that of [(phen2N2)Fe]2O. The spectrum of [(Pc)Fe]2O is composed of a sharp peak at 398.4 eV with a satellite peak centered at 400.1 eV (Fig. 3c). Analogously, [(OEP)Fe]2O consists of a sharp peak at 397.6 eV with a broad satellite peak centered at 399.9 eV64,65 (Fig. 3d). While the main peak in [(Pc)Fe]2O appears in the region assigned to Npyridinic for Fe-N-C, it is best fit with a single component, indicating that the coordinating and non-coordinating N atoms have comparable binding energies. Thus, the exclusive presence of phthalocyanine environments in Fe-N-C would be insufficient to account for the large metal-Nx peak in Fe-N-C. Notably, N 1 s peaks for (phen2N2)FeCl, (Pc)FeCl, and (OEP)FeCl (Supplementary Fig. 11) appear within 0.1–0.4 eV of the corresponding peaks for the μ-oxo compounds, indicating that the identity of the axial ligand does not impact the N 1s binding energy to the same extent as does changing the metal-coordinated nitrogen atoms from pyrrolic to pyridinic. Importantly, the N 1s peaks for the coordinated pyridinic nitrogens in the (phen2N2)Fe complexes match well with the peak corresponding to the metal-coordinated pyridinic nitrogen component (399.9 eV) of Fe-N-C, whereas the N 1s peaks of the coordinated pyrrolic nitrogens in (Pc)Fe and (OEP)Fe complexes appear at significantly lower binding energies. Together, the XPS data indicate that the iron-coordinated N environment in [(phen2N2)Fe] species are electronically very similar to the metal-coordinated N environments in Fe-N-C materials.

The iron environments present in Fe-N-C, [(phen2N2)Fe]2O, [(Pc)Fe]2O, and [(OEP)Fe]2O were also examined by XPS (Supplementary Table 6). Consistent with previously reported data for Fe-N-C materials60,66, we observe Fe 2p3/2 peaks at 709.5 and 713.9 eV (Fig. 3e) assigned to Fe(II) and Fe(III) formal oxidation states, respectively (Supplementary Table 7)60. In contrast, [(Pc)Fe]2O (Fig. 3g) exhibits Fe 2p3/2 and 2p1/2 peaks at 708.9 and 722.0 eV, respectively, and [(OEP)Fe]2O (Fig. 3h) displays Fe 2p3/2 and 2p1/2 peaks at 709.2 and 723.2 eV, respectively. As reported for iron porphyrin and phthalocyanine samples, we also observe significant asymmetry on the main Fe 2p3/2 peak for both [(OEP)Fe]2O and [(Pc)Fe]2O compounds that is attributed to multiplet splitting arising from core-hole interactions with the open-shell electronic structure of the high-spin ferric centers67,68. Similar features are observed for (OEP)FeCl and (Pc)FeCl, albeit with a ~0.5–1.5 eV shift to higher binding energy (Supplementary Figs. 13 and 14). These XPS features are distinct from those observed for [(phen2N2)Fe]2O (Fig. 3f) which displays Fe 2p3/2 and 2p1/2 peaks at 710.8 and 724.3 eV. We note that (phen2N2)FeCl shows Fe 2p3/2 and 2p1/2 peaks at similar binding energies, 710.5 and 723.9 eV, respectively (Supplementary Fig. 15), and that residual FeCl3 salts are likely subsumed into these peaks69. As with [(OEP)Fe]2O and [(Pc)Fe]2O, we also observe significant asymmetry in the Fe 2p3/2 and Fe 2p1/2 peaks of [(phen2N2)Fe]2O that we also attribute to core-hole interactions. Importantly, we observe a ~1.5–1.9 eV shift to higher binding energy for the main Fe 2p3/2 peak for [(phen2N2)Fe]2O relative to both [(OEP)Fe]2O and [(Pc)Fe]2O. This observation is consistent with increased π-acidity of the pyridinic macrocycle in [(phen2N2)Fe]2O, which withdraws electron density from the iron center and is mirrored by the positions of the Fe–O–Fe peaks evident in the high-resolution O 1 s spectra of the μ-oxo complexes (Supplementary Fig. 16 and Supplementary Table 8). Notably, the peak in Fe-N-C assigned to Fe(III) is 2.7 eV positive of the corresponding Fe(III) peak for [(phen2N2)Fe]2O but even more positive than the same peak in [(OEP)Fe]2O and [(Pc)Fe]2O. These data suggest that while the Fe(III) centers in Fe-N-C may exist in an even more withdrawing ligation environment, a pyridinic macrocycle complex such as [(phen2N2)Fe]2O provides a better structural model for Fe-N-C than pyrrolic macrocycles such as [(OEP)Fe]2O and [(Pc)Fe]2O. Indeed, the strongly electron-withdrawing environment in the material helps explain the positive shift of the putative Fe(II) component of Fe-N-C, which makes it appear close in energy to the main Fe 2p3/2 peaks of the Fe(III) complexes. Overall, the XPS data are consistent with nitrogen and iron environments in [(phen2N2)Fe]2O that are more electropositive than the pyrrolic macrocycles and more similar to the metal-Nx sites in Fe-N-C.

XAS results demonstrate a strong similarity with Fe-N-C

We next examined the electronic structure and coordination environment of the iron centers in Fe-N-C, [(phen2N2)Fe]2O, [(OEP)Fe]2O, and [(Pc)Fe]2O by XAS. The XANES spectrum of our Fe-N-C preparation (Fig. 4a, black) matches those reported in the literature70. While a rigorous analysis of the X-ray absorption near edge structure (XANES) spectra for Fe-N-C materials is challenging due to the presumed presence of a mixture of Fe(II) and Fe(III) (Supplementary Table 7) as well as an unknown degree of heterogeneity in the local coordination environment of each iron, the XANES line shapes have been examined for a wide variety of pyrolyzed Fe-N-C catalysts, including Fe-N-C derived from iron pyrrolic macrocycles, and features of the XANES have been correlated to pyrolysis temperature and ORR activity26,70,71. In particular, the intensity of the first main-edge peak, C, has been found to positively correlate with increased pyrolysis temperature as well as improved ORR activity, whereas the intensities of the main-edge shoulder, B, and the higher energy main-edge peak, D, have been shown to anticorrelate with both pyrolysis temperature and ORR activity (Fig. 4a, dotted vertical lines)70. Notably, the XANES spectra of [(OEP)Fe]2O (Fig. 4a, orange) and [(Pc)Fe]2O (Fig. 4a, aqua) show enhanced intensity for D with [(OEP)Fe]2O also showing enhanced intensity for B. These features contrast with the XANES spectrum of [(phen2N2)Fe]2O (Fig. 4a, blue), which shows a higher intensity for C, and lower intensities for B and D. The intensity of pre-edge peak, A, has also been shown to positively correlate with ORR activity70. We find that the pre-edge peak line shape for [(phen2N2)Fe]2O matches closely with that of Fe-N-C, but that the peak intensity for both is lower than that for [(OEP)Fe]2O and dramatically lower than the sharp pre-edge feature observed for [(Pc)Fe]2O (Supplementary Fig. 17). Given the high sensitivity of the pre-edge peak to the identity of the axial ligand in similar tetrapyrrolic complexes72 as well as distortions in the Fe-N4 plane resulting from variation of the Fe-O-Fe angle in [(OEP)Fe]2O55,73 and [(Pc)Fe]2O59, we refrain from overinterpreting the pre-edge peak shapes or intensity74. Nonetheless, the suppressed intensity at B and D and increased intensity at C for [(phen2N2)Fe]2O suggest that the (phen2N2)Fe molecular analogue is a superior model for the active sites in Fe-N-C materials relative to pyrrolic macrocycles.

Fig. 4: X-ray absorption spectroscopy data.
figure 4

XANES spectra (a) and expanded main-edge region (inset), k2-weighted Fe k-edge EXAFS spectra (b) and k2-weighted Fourier transform Fe EXAFS spectra (c). The energy values of the vertical lines and the alphabetical labels in (a) are taken from reference70. Fe-N-C is shown in black, [(phen2N2)Fe]2O in blue, [(OEP)Fe]2O in orange and [(PcFe)]2O in aqua.

Extended X-ray absorption fine structure (EXAFS) data provide further evidence in support of the structural similarity between the iron coordination environments in [(phen2N2)Fe]2O and Fe-N-C. The k2-weighted EXAFS oscillations for Fe-N-C (Fig. 4b, black) exhibit remarkably similar amplitudes and periods to the EXAFS of [(phen2N2)Fe]2O (Fig. 4b, blue) out to ~10.0 Å−1 with only a small phase shift beyond ~6.0 Å−1. In contrast, the k2-weighted EXAFS for [(OEP)Fe]2O (Fig. 4b, orange) and [(Pc)Fe]2O (Fig. 4b, aqua) displays amplitudes and periods that differ dramatically from the EXAFS of [(phen2N2)Fe]2O and Fe-N-C beyond ~3.5 Å−1. For example, whereas traces for both Fe-N-C and [(phen2N2)Fe]2O pass through χ(k)k2 = 0 at eight different points between 2.5 and 10 Å−1, [(OEP)Fe]2O and [(Pc)Fe]2O do so nine and eleven times, respectively. Furthermore, the similarity between Fe-N-C and [(phen2N2)Fe]2O is also reflected in the k2-weighted Fourier transform EXAFS radial distribution spectra (Fig. 4c). The [(phen2N2)Fe]2O complex displays a broad primary coordination shell scattering peak at 1.36 Å apparent distance, similar to the first shell peak for Fe-N-C at 1.46 Å apparent distance. In contrast, the first shell scattering peaks for [(OEP)Fe]2O and [(Pc)Fe]2O appear at 1.62 and 1.47 Å apparent distance and display prominent shoulders at lower apparent distances that are not observed in Fe-N-C or [(phen2N2)Fe]2O. Likewise, both [(phen2N2)Fe]2O and Fe-N-C have no prominent scattering interactions beyond 2.25 Å, whereas significant  higher-order scattering is observed for [(OEP)Fe]2O and [(Pc)Fe]2O. Taken together, the raw EXAFS data for Fe-N-C mostly match the spectra of [(phen2N2)Fe]2O and are quite distinct from those of either [(OEP)Fe]2O or [(Pc)Fe]2O.

The EXAFS peaks for all four materials are well modeled with a five-coordinate Fe center bearing four equatorial Fe-N scatterers and one axial Fe-O scatterer (Supplementary Table 9). The fits (Supplementary Figs. 18 and 19) from modeling the data return Fe-N scattering paths of 1.94, 1.97, 2.06, and 1.94 Å for Fe-N-C, [(phen2N2)Fe]2O, [(OEP)Fe]2O, and [(Pc)Fe]2O, respectively. The Fe-N distances for both [(OEP)Fe]2O and [(Pc)Fe]2O agree with the corresponding distances extracted from crystal structures55,75,76. Importantly, these Fe–N bond lengths reflect not only the N–N separation in the ligand, but also the degree of pucker of the iron center out of the equatorial plane. Thus, this distance alone cannot distinguish pyridinic from pyrrolic ligation and, indeed, we see similar Fe–N vectors for [(phen2N2)Fe]2O and [(Pc)Fe]2O. Furthermore, for [(phen2N2)Fe]2O, the 1.97 Å Fe-N distance extracted from EXAFS modeling is substantially higher than the 1.86 Å distance predicted from the calculation if the iron were to reside in the N4 plane for the phen2N2 ligand (Supplementary Fig. 20), further evincing that the iron center is puckered. This reasoning is also in line with a computational XAS study that showed an enhancement of the main-edge peak C (Fig. 4a, blue) as the displacement of iron from the N4 plane was increased70. Consistent with the Fe-N-C material having a putative OHx axial ligand, the EXAFS fits return an Fe–O scattering path of 2.04 Å, slightly larger than the range of Fe–O scattering paths, 1.73–1.79 Å, extracted for the molecular μ-oxo complexes.

Taking the raw k2-weighted EXAFS oscillations, the FT-EXAFS spectra, and the degree of iron puckering into account, the XAS data highlight that, relative to (Pc)Fe and (OEP)Fe, (phen2N2)Fe is an improved model of the iron sites in Fe-N-C catalysts. We stress that the similarity in the k-space EXAFS data should not be taken to mean that (phen2N2)Fe has an identical structure to Fe-N-C, but that the aggregate scattering environment of the iron centers in (phen2N2)Fe is qualitatively similar to the average cumulative scattering environment of the iron centers in Fe-N-C. We acknowledge this resemblance could be coincidental and introduced by countervailing changes in axial and equatorial scattering interactions. Nonetheless, the data indicate that the iron centers in (phen2N2)Fe exist in a qualitatively similar average environment to the iron centers in Fe-N-C.

Fe(III/II) potentials are defined by ligating and proximal N atoms

All three model compounds as well as the Fe-N-C material were evaluated electrochemically as thin films supported on glassy carbon electrodes. In a typical preparation, Fe-N-C powders were dispersed in a 7:2:1 combination of CH2Cl2, ethanol, and 5 wt% Nafion solution (75 wt% ethanol and 20 wt% water), respectively. The resulting inks were dropcast onto electrodes and allowed to dry in air to generate a well-adhered catalyst film. A similar procedure was used for (phen2N2)FeCl, (OEP)FeCl, and (Pc)FeCl with inclusion of Vulcan carbon powder to enhance film conductivity. We expect that any residual FeCl3 salts present in the (phen2N2)FeCl sample will readily dissolve into the acidic electrolyte and will not impact the electrochemical results. In line with this expectation, we find that FeCl3/Vulcan inks are inactive for ORR (Supplementary Fig. 21).

Cyclic voltammograms of Fe-N-C, (phen2N2)FeCl, (OEP)FeCl, and (Pc)FeCl recorded in the absence of O2 provide insight into the redox potential of the metal center. For (OEP)FeCl (Fig. 5, orange), we observe a redox feature with E1/2 = 0.27 V (all potentials are reported vs the reversible hydrogen electrode, RHE). We note that the Fe(III/II) redox couple of (OEP)FeCl is quite broad with a peak-to-peak separation of 315 mV. We attribute this to sluggish Fe(III/II) redox self-exchange through the film, but nonetheless, we note that the observed E1/2 value is comparable to other carbon-adsorbed iron porphyrin compounds17,56,77,78. For (Pc)FeCl (Fig. 5, aqua), we observe a broad redox feature with E1/2 = 0.61 V (Supplementary Fig. 22), similar to reported values for carbon-supported iron phthalocyanine complexes79. For (phen2N2)FeCl (Fig. 5, blue), we observe a reversible redox wave at 0.59 V. Based on the known Nernstian pH dependence of Fe(III/II) couples for adsorbed porphyrin complexes80 as well as the quasi-Nernstian behavior of the redox wave for (phen2N2)Fe (Supplementary Fig. 23), we assign this redox process to the one-electron, one-proton reduction of Fe(III)-OH to Fe(II)-OH2.

Fig. 5: Cyclic voltammograms of adsorbed catalysts.
figure 5

Rotating glassy carbon disk electrodes are shown modified with catalyst films containing Fe-N-C (black), (phen2N2)FeCl (blue), (Pc)FeCl (aqua, 4× vertical expansion), and (OEP)FeCl (orange). Data were recorded at 5 mV s−1 and 2000 rpm rotation rate in O2-free 0.1 M HClO4 electrolyte.

For Fe-N-C (Fig. 5, black), we observe a large double-layer capacitance, consistent with the high surface area of the material, and a pronounced redox wave at 0.63 V (Fig. 5). Although in situ spectroscopic data are required for an unambiguous assignment, we tentatively attribute this redox wave to proton-coupled electron transfer (PCET) reactions of edge-localized quinone and hydroxyl moieties, rather than to an Fe(III/II) redox process. Although this assignment may seem counterintuitive, we favor it for several reasons. First, quinone and hydroxyl PCET reactions are known to occur in the ~0.6 V potential region on carbon powders81. Second, integrating the observed 0.6 V redox wave yields a charge that is 3.4 times larger than the expected charge for a 1-electron redox process of the surface exposed iron centers in the Fe-N-C material82. Third, the potential of the wave is comparable to the value for (Pc)Fe and (phen2N2)Fe and this is inconsistent with the expectation that the extended π framework in Fe-N-C should raise the Fe(III/II) potential83. Fourth, Fe-N-C catalyzes ORR at potentials ~0.2 V positive of the observed redox wave. Thus, if the observed 0.6 V redox wave were assigned to the Fe(III/II) couple, the equilibrium fraction of catalytically active Fe(II)-N4 sites at catalytic onset would be very small. Finally, other reports have observed waves for Fe-N-C materials at ~0.8 V84,85,86, in line with the onset of ORR catalysis at Fe-N-C materials (see below). We postulate that the actual Fe(III)-OH/Fe(II)-OH2 redox process for this Fe-N-C material is obscured by the large double-layer charging background and the likely distribution of iron redox potentials. We also note that some iron redox centers may not engage in PCET reactivity and would not be expected to display a redox wave87.

The redox potentials  extracted from the model compounds provide valuable information about the factors that may contribute to the redox potentials of the iron centers in Fe-N-C materials. Despite the fact that both (Pc)Fe and (OEP)Fe have pyrrolic ligating atoms, the redox potential for (Pc)Fe is ~0.3 V positive of the redox potential of (OEP)FeCl. The principle structural differences between (Pc)Fe and (OEP)Fe are the presence of N vs C atoms in the meso positions and the presence of a more extended π system in (Pc)Fe. One study has found that iron octaethyltetraazaporphyrin possesses a similar Fe(III/II) redox potential to (Pc)Fe88, suggesting that the presence of electronegative meso-N atoms is the principal contributor to the dramatic positive shift observed. Notably, whereas (phen2N2)FeCl possesses two non-ligating nitrogen atoms in the local environment, (Pc)FeCl has four, yet their Fe(III/II) potentials are comparable. This highlights that the less electron-donating pyridinic coordination environment in (phen2N2)FeCl is an ideal structural motif for pushing the Fe(III/II) positive. Together, the data suggest that for the iron centers in the Fe-N-C material, the effective redox potential is due, not only to the ligating heterocycles, but also the nitrogen population near the Fe center16,89,90. Thus, even Fe-N4 sites with identical primary coordination spheres may display a distribution of redox properties depending on the population and position of non-ligating proximal nitrogen atoms.

The observed Fe(III/II) redox waves result from only a fraction of the catalyst loaded into the dropcast film. The integrated charge in the Fe(III/II) redox waves of (phen2N2)FeCl, (OEP)FeCl, and (Pc)FeCl catalyst film corresponds to 7%, 43%, and 2% of the total catalyst loading for each compound, respectively (Supplementary Table 10). We attribute the higher electroactive percentage in (OEP)FeCl film to the improved solubility of the porphyrin catalyst, which leads to superior catalyst dispersion within the film. Nonetheless, these PCET redox potentials provide a good indication that the iron centers in (phen2N2)Fe and (Pc)Fe are more electropositive than those in (OEP)Fe.

(Phen2N2)FeCl catalyzes ORR with similar activity to (Pc)FeCl

(Phen2N2)FeCl is a potent catalyst for the ORR. In O2-saturated 0.1 M HClO4, the reversible surface redox wave at 0.59 V (Fig. 6, black) is replaced by a large catalytic wave that displays an onset potential of 0.75 V (all onset potentials correspond to a current density of –0.1 mA cm−2 and all electrochemical performance parameters are collected in Supplementary Table 11) and reaches a current plateau at ~0.5 V (Fig. 6, red). This catalytic wave spans the same potential range as the reversible redox feature in the absence of O2 suggesting that ORR catalysis is mediated by the Fe(III/II) redox process (Fig. 6, inset). We also find that the Fe center is critical for activity. The unmetalated (phen2N2)H2 ligand has activity comparable to the carbon background (Fig. 7, green) in acidic media with an onset potential of 0.34 V (Fig. 7, magenta) and activity slightly higher than background in alkaline media with an onset potential of 0.75 V, 140 mV negative of (phen2N2)FeCl (Supplementary Figs. 24 and 25). Catalytic onset for (phen2N2)FeCl (Fig. 7, blue) is 320 and 30 mV positive of the onset observed for (OEP)FeCl and (Pc)FeCl, respectively. Catalytic activity is improved in basic media with an onset of 0.89 V in 0.1 M KOH (Supplementary Fig. 24, blue) for (phen2N2)FeCl, similar to the onset observed for (Pc)FeCl and 150 mV positive of the onset for (OEP)FeCl.

Fig. 6: Cyclic voltammograms of adsorbed (phen2N2)FeCl.
figure 6

A rotating glassy carbon disk electrode modified with a catalyst film containing (phen2N2)FeCl in N2- (black) and O2- (red) saturated 0.1 M HClO4 aqueous electrolyte. Data were recorded at 5 mV s−1 and 2000 rpm rotation rate.

Fig. 7: Linear sweep ORR voltammograms of adsorbed catalysts.
figure 7

Glassy carbon disk electrodes modified with catalyst films containing Fe-N-C (black), (phen2N2)FeCl (blue), (Pc)FeCl (aqua), (OEP)FeCl (orange), Vulcan carbon (green), and (phen2N2)H2 (magenta) in O2-saturated 0.1 M HClO4 electrolyte. Data were recorded at 5 mV s−1 and 2000 rpm rotation rate.

The above qualitative activity trends are also reflected in the per site TOF values for the three model complexes. TOF values, in electrons passed per site per second, were extracted as a function of potential by dividing the current density by the integrated charge passed in the Fe(III/II) redox feature. In accordance with the raw voltammogram data in Fig. 6, (phen2N2)FeCl displays a 1000-fold higher TOF than (OEP)FeCl in the activation-controlled region at 0.55 V in 0.1 M HClO4, but comparable TOF values to that of (Pc)FeCl (Supplementary Fig. 26a and Supplementary Table 12). In 0.1 M NaOH electrolyte, (phen2N2)FeCl and (Pc)FeCl display TOF values that are 280- and 1100-fold higher than (OEP)FeCl at 0.80 V (Supplementary Fig. 26b and Supplementary Table 12).

This positive shift in onset potential and the corresponding increase in TOF for (phen2N2)FeCl and (Pc)FeCl relative to (OEP)FeCl is consistent with the positive shift of the corresponding Fe(III/II) redox potentials for the former compounds. These results are in line with prior work that identified scaling relationships in ORR activity among adsorbed porphyrins and phthalocyanines, and showed that catalytic activity is positively correlated with the Fe(III/II) potential91,92. While a detailed mechanistic analysis of the ORR profile of these catalysts is beyond the scope of this work, the observed correlation among adsorbed Fe-N4 compounds could be rationalized by the following simplified mechanistic sequence:

$${\mathrm{Fe}}^{III} - {\mathrm{OH}} + e^ - + {\mathrm{H}}^ + \,\rightleftarrows\, {\mathrm{Fe}}^{II} - {\mathrm{OH}}_2\quad \quad K_1$$
(1)
$${\mathrm{Fe}}^{II}-{\mathrm{OH}}_2 + {\mathrm{O}}_{2} \to {\mathrm{Fe}}^{III} - {\mathrm{O}}_2 + {\mathrm{OH}}_2\quad \quad k_2\quad {\mathrm{RLS}}$$
(2)

In this sequence, at any given E, the rate of the reaction will be given by the product, K1 × k2, of the equilibrium constant, K1, for the Fe(III)-OH to Fe(II)-OH2 conversion, Eq. (1), and the rate constant, k2, for rate-limiting O2 binding, Eq. (2). If k2 is roughly insensitive to the local structure of the Fe center, then the reaction rate will be predominantly gated by the Fe(III/II) redox process and the higher redox potentials will correlate with more available Fe(II) at a given E, resulting in faster catalysis. We acknowledge that the above mechanistic picture is speculative and will require more studies to validate, but it nonetheless provides a simple framework for rationalizing the observed reactivity trend. Furthermore, our data provide the first experimental evidence that changing from pyrrolic to pyridinic coordination does not dramatically alter the scaling relationship between ORR activity and Fe(III/II) potential. This provides further support for the notion that Fe-N-C materials contain pyridinic Fe-N4 sites with sufficiently high redox potentials to mediate ORR at relatively low overpotentials.

The electrocatalytic data establish that (phen2N2)FeCl and (Pc)FeCl have superior activity relative to (OEP)FeCl, whereas both remain at a deficit to Fe-N-C. While the Fe(III/II) redox potential is difficult to discern for Fe-N-C, the positive shift of the Fe(III) peak in the XPS suggests that the iron centers in Fe-N-C are even more electropositive than those in (phen2N2)FeCl and (Pc)FeCl. This change may contribute to the higher onset potentials of 0.85 and 0.90 V observed for the Fe-N-C catalyst in acidic and alkaline media, respectively17. We stress that although (Pc)FeCl and (phen2N2)FeCl display comparable activity for ORR, (Pc)FeCl is an inferior structural model on the basis of the spectroscopic results presented above. In aggregate, the spectroscopic as well as electrochemical results strongly suggest that (phen2N2)FeCl is the more effective model complex for mimicking iron-containing active sites in Fe-N-C relative to pyrrolic complexes such as (Pc)FeCl. Furthermore, it follows that observing high catalytic ORR performance is insufficient evidence to establish a molecular complex as an accurate and comprehensive molecular model for the active sites in Fe-N-C materials. The deficit in activity relative to Fe-N-C may also result, in part, from weak interaction between the molecular orbitals of the model and the band states of the carbon host. Notwithstanding, the fact that a discrete pyridinic molecular complex such as (phen2N2)FeCl displays an ORR onset within 150 mV of champion Fe-N-C materials suggests enormous opportunities for rational molecular design of highly active Fe-based ORR catalysts based on pyridinic ligation motifs that structurally model Fe-N-C.

(Phen2N2)FeCl mirrors the selectivity trends of Fe-N-C

Furthermore, (phen2N2)FeCl displays high selectivity for the four-electron reduction of O2 that is comparable to Fe-N-C and greater than that of (OEP)FeCl or (Pc)FeCl. Using rotating ring disk electrode (RRDE) voltammetry (Supplementary Figs. 27 and 28) we determined the percent H2O2 produced and electrons transferred as a function of applied potential for all four catalysts (Fig. 8 and Supplementary Figs. 29 and 30). For (phen2N2)FeCl, H2O2 production stabilizes rapidly, reaching values of 0.1% and 2.7% in acid and alkaline media at 0.40 V, respectively. These values correspond to 3.99 and 3.95 electrons transferred in each condition, respectively. Indeed, in both acidic and alkaline media, the selectivity of (phen2N2)FeCl in the transport-limited region surpasses that of Fe-N-C at the same potential. Further, in stark contrast to (phen2N2)FeCl, both (Pc)FeCl and (OEP)FeCl display significantly lower selectivity in acid media, generating 6.6% and 12.5% H2O2, respectively, at 0.40 V. In 0.1 M NaOH, (Pc)FeCl displays similar selectivity relative to (phen2N2)FeCl; however, both are slightly more selective than (OEP)FeCl (Supplementary Fig. 29). We stress that the RRDE results are best interpreted in qualitative rather than quantitative terms because apparent H2O2 yields are strongly dependent on catalyst loading, film morphology, ink composition, and carbon support identity93,94,95. Nevertheless, these results highlight the ability of a carbon-adsorbed pyridinic Fe-N4 coordination environment to facilitate selective O2-reduction pathways in both acidic and alkaline media.

Fig. 8: %H2O2 vs potential for adsorbed catalysts.
figure 8

All data were recorded in O2-saturated 0.1 M HClO4 electrolyte at 5 mV s−1 and 2000 rpm rotation rate. (phen2N2)FeCl is shown in blue, (OEP)FeCl is shown in orange, (Pc)FeCl is shown in aqua, and Fe-N-C is shown in black.

Whereas Fe-N-C materials are relatively stable, we observe limited stability of the (phen2N2)FeCl catalyst with activity decaying in acidic media over the course of several slow-scan cyclic voltammograms (15–20 min). Analogous deactivations are also observed for the pyrrolic complexes and are documented in the literature96,97,98. These observations highlight the important role of the carbon framework in increasing the relative stability of Fe-N4 sites in Fe-N-C materials against oxidative and protolytic decomposition induced by the acidic conditions and the presence of parasitic amounts of H2O299. Indeed, we posit that extending the aromatic periphery around the (phen2N2)FeCl active site could enhance stability and allow for the bottom-up synthesis of robust Fe-based ORR catalysts.

The results reported herein provide a molecular perspective on the structure and oxygen reduction reactivity of Fe-N4 active sites in Fe-N-C materials. We have synthesized a new (phen2N2)Fe fragment and demonstrated that it is a superior molecular model for the putative Fe-N4 active sites in Fe-N-C materials compared to exhaustively studied iron porphyrin and phthalocyanine complexes. Electrochemical studies establish that ORR activity is positively correlated to the Fe(III/II) potential and that, while (OEP)Fe has too low of a potential to mediate efficient catalysis, both phthalocyanine- and pyridine-based ligation environments in (Pc)Fe and (phen2N2)Fe can generate a positive shift of the Fe(III/II) potential and a corresponding increase in ORR activity. Among the model complexes, the (phen2N2)Fe platform is unique in displaying both high activity and near 100% selectivity for four-electron oxygen reduction in acidic media, the very characteristics found in Fe-N-C materials. Since high electrochemical performance does not necessarily imply structural similarity, our spectroscopic results provide additional discrimination. In particular, the pyridinic ligation environment in (phen2N2)Fe leads to XPS and XAS signatures that are remarkably similar to those of Fe-N-C materials and notably distinct from those in either (OEP)Fe or (Pc)Fe. Taken in aggregate, the spectroscopic similarity and the electrochemical activity and selectivity trends indicate that, relative to (OEP)Fe or (Pc)Fe, (phen2N2)Fe is a significantly improved structural and functional model of Fe-N-C materials. Since the (phen2N2)Fe core can be readily derivatized100,101 and used as the building block for functional catalytic materials, the molecular model complex developed here provides a powerful platform with which to advance the synthesis and understanding of single-site heterogeneous electrocatalysts for critical energy conversation reactions.

Methods

General synthetic considerations

Where indicated, synthetic procedures were carried out under an inert atmosphere in a nitrogen-filled glovebox. All other synthetic transformations were carried out on the benchtop without effort to exclude dioxygen or moisture. Anhydrous 1,10-phenanthroline (99%), 1,3-dibromopropane (98%), tert-butanol (99%), phosphorus pentachloride (98%), and phthalonitrile (98%) were obtained from Alfa Aesar and used as received. Potassium tert-butoxide (97%) and phosphoryl chloride (99%) were obtained from TCI and Sigma Aldrich, respectively and used as received. Iron(III) chloride (98%) was purchased from Strem Chemicals and stored in a nitrogen-filled glovebox. Compressed anhydrous ammonia (99.995%) was purchased from Airgas. N,N-dimethylformamide was deoxygenated and dried using a Glass Contour System (SG Water USA, Nashua, NH) and stored in the glovebox over 4 Å molecular sieves. D2O, CDCl3 and d-TFA were purchased from Sigma-Aldrich or Cambridge Isotope Laboratories and were used without further purification. 2, 3, 7, 8, 12, 13, 17, 18-Octaethyl-21H, 23H-porphine iron(III) chloride, (OEP)FeCl, was purchased from Frontier Scientific and used without further purification. Iron(II) phthalocyanine for use as a model complex in XAS data analysis was purchased from Alfa Aesar and sublimed at 600 °C under reduced pressure in a single-zone tube furnace for 3 h. Routine NMR spectra were recorded on Varian Mercury 300, Bruker Avance III 400, and Varian Inova 500 spectrometers. Chemical shifts for 1H and 13C{1H} spectra are reported in ppm downfield of TMS, with spectra referenced using the chemical shifts of the solvent residuals. Spectra recorded in d-TFA were referenced to a benzene solvent residual by including a small capillary of C6D6 in the sample tube. UV–Visible spectra were measured in a 1-cm quartz cell on a Varian Cary 50 spectrophotometer. MALDI-TOF mass spectra were obtained using Bruker Autoflex LRF and Bruker Omniflex instruments operating in reflectron mode, and the peaks reported are the mass of the most intense peak in the isotope envelope. MALDI-TOF samples consisted of analyte mixed with 1,4-bis(5-phenyl-2-oxazolyl)benzene (POPOP) as a desorption matrix. Elemental analyses and inductively coupled plasma mass spectra (ICP-MS) were performed by Robertson Microlit Laboratories (Ledgewood, NJ).

Synthesis of Fe-N-C

Fe-N-C was synthesized by a hybrid method adapted from previously published procedures19,48. 0.019 g (0.11 mmol), Fe(OAc)2, 0.206 g (1.14 mmol), 1,10-phenanthroline, and 0.804 g (3.53 mmol) ZIF-8 MOF were mixed together in an agate mortar for 15 min. To remove excess water and oxygen, the prepyrolysis mixture was placed under vacuum for 30 min at 90 °C and subsequently held under vacuum for a further 12 h at room temperature. 0.856 g of the precatalyst powder was weighed into an alumina boat which was positioned at the midpoint of an alumina tube centered in a single-zone tube furnace. The alumina tube was sealed with steel endcaps, evacuated briefly, and then continuously purged with argon. The furnace was heated to 1000 °C at a ramp rate of 10 °C min−1 and maintained at 1000 °C for 60 min. The furnace was then allowed to return to room temperature. Subsequently, the alumina tube was evacuated briefly and then continuously purged with 5% hydrogen in argon. The furnace was ramped to 800 °C at a rate of 10 °C min−1 and maintained at 800 °C for 30 min. The sample was then allowed to return to room temperature. The resulting crude Fe-N-C powder was then sonicated in 30 mL of 0.1 M H2SO4 for 60 min. The black suspension was filtered and washed with water until the eluant pH was neutral. The sample was subsequently washed with acetone to remove excess water and the product was dried overnight at 60 °C to yield 219.2 mg of Fe-N-C as a black powder. ICP-MS: 1.07% Fe. 57Fe Mössbauer (90 K): [D1: (δ = 0.46 mm s−1, |ΔEQ| = 1.08 mm s−1, 71%), D2: (δ = 0.37 mm s−1, |ΔEQ| = 3.06 mm s−1, 29%)].

Synthesis of 6,7-dihydro-5H-1,4-diazepino[1,2,3,4-Imn][1,10]phenanthroline-4,8-diium bromide (2)

Compound 2 was synthesized via alkylation of 1,10-phenanthroline using an excess of 1,3-dibromopropane in refluxing toluene. 10.787 g (59.86 mmol) 1,10-phenanthroline was suspended in 105 mL toluene. The mixture was stirred and heated to 70 °C and, subsequently, 28 mL (55.47 g, 275 mmol, 4.59 equiv.) 1,3-dibromopropane was added. The temperature was increased to 120 °C and the mixture was refluxed for 4 h. After allowing the reaction vessel to cool, the mixture was filtered and washed with hexanes to yield 18.688 g (82%) of compound 2 as a yellow powder. The observed NMR peaks in D2O matched the literature102.

Synthesis of 6,7-dihydro-5H-1,4-diazepino[1,2,3,4-Imn][1,10]phenanthroline-3,9-dione (3)

Compound 3 was prepared using the modified workup described in the literature103. 5.061 g (13.24 mmol) of compound 2 was suspended in 85 mL tert-butanol and sonicated for 15 min. The mixture was then stirred while 6.026 g (53.7 mmol, 4.06 equiv.) KOtBu was added in small portions over the course of 15 min. The reaction mixture was then heated to 40 °C and stirred for 12 h. The solvent was removed by rotary evaporation and the crude material was suspended in 100 mL of water. The product was extracted with 100 mL of chloroform and 5% methanol by volume was added to the chloroform solution. The mixture was then filtered through a plug of silica on a glass frit and the silica was washed with chloroform until the eluant was colorless. The combined washings were concentrated to dryness by rotary evaporation to yield 1746 g (52%) of compound 3 as a brown solid. The observed NMR peaks in CDCl3 matched those reported in the literature102.

Synthesis of 2,9-dichloro-1,10-phenanthroline (4)

Under inert atmosphere, a mixture of 2.29 g (9.06 mmol) 3 and 3.77 g (18.1 mmol, 2.00 equiv.) PCl5 was suspended in 35 mL POCl3. The mixture was then refluxed under inert atmosphere for 14 h. After cooling to room temperature, the solution was poured onto 600 mL of ice and the resulting mixture was neutralized with aqueous ammonium hydroxide (30%) to a pH > 8. After neutralization, the resulting precipitate was collected by filtration. The solid was washed with water and dried overnight at elevated temperature to yield 1.99 g (89%) of compound 4 as a light brown powder. The observed NMR peaks in CDCl3 matched those given in the literature102.

Synthesis of (phen2N2)H2

Preparation of (phen2N2)H2 has been previously described in the literature45,49,104, however an alternate method is presented here. 0.547 g (2.19 mmol) 2,9-dichlorophenanthroline was added to a cylindrical glass insert and enclosed at room temperature in a 100 mL Parr bomb equipped with a rupture disk. The bomb was purged with nitrogen for 10 min and was then pressurized with anhydrous ammonia at 114 psi. The bomb was then immersed in a bed of aluminum beads and heated to 280–300 °C with a heating mantle for 24 h. Following additional heating for 12 h at 300 °C, the bomb was allowed to return to room temperature. The residual ammonia was vented and the crude product was dissolved in a mixture of trifluoroacetic acid, acetic acid and methanol and stirred for 30 min. The mixture was neutralized and basified with 4 M NaOH and was stirred for an additional 12 h. The precipitate was filtered and sequentially washed with ethanol and chloroform until the washings were colorless. The isolated material was then dried at 60 °C for 12 h. The filtrate was concentrated in vacuo and heated to 300 °C under inert atmosphere for a period of 24 h in a 500 mL round bottom flask affixed to a reflux condenser. After cooling to room temperature, the solid derived from the filtrate was treated with an identical dissolution, precipitation, and washing sequence as before to yield a second crop. In total, 0.280 g (0.506 mmol, 66% combined yield) of 3bH,10bH-1,14:7,8-diethenotetrapyrido[2,1,6-de:2′,1′,6′-gh:2″,1″,6″-kl:2″′,l″′,6″′-na][1,3,5,8,10,12]hexaazacyclotetradecine, (phen2N2)H2, was isolated as a brown solid. 1H NMR (C6D6 in d-TFA): δ 9.41 (d, 4H, 10 Hz), 8.76 (s, 4H), 8.49 (d, 4H, 10 Hz). MALDI− MS (POPOP matrix): m/z 386.03 ([M]+ calc. for C24H14N6: 386.13). UV–Vis (DMSO): λmax = 287 nm (ε = 23,419 L mol−1 cm−1), 322 (8,119), 339 (6,054), 360 (4,828), 376 (4,069), 439 (550), 467 (202). Anal. Calcd. for (phen2N2)H2•H2O (C24H16N6O1): C, 71.28; H, 3.99; N, 20.78. Found: C, 70.93; H, 3.47; N, 21.12.

Synthesis of (phen2N2)FeCl

Under inert atmosphere, 0.060 g (0.155 mmol) (phen2N2)H2 was added to a pressure tube charged with a stirbar. 0.036 g (0.22 mmol, 1.4 equiv.) FeCl3 and 0.221 mL (0.930 mmol, 6.00 equiv.) N(n-Bu)3 were added to the vessel followed by 7 mL DMF. The tube was sealed and heated to 170 °C for 36 h with vigorous stirring. The temperature was allowed to return to ambient levels and the mixture was diluted with 20 mL CH2Cl2 under inert atmosphere. The mixture was then cooled overnight at −38 °C and the resulting precipitate was filtered and washed with copious amounts of ether and CH2Cl2 to yield 54 mg (73%) 1,14:7,8-Diethenotetrapyrido[2,1,6-de:2′,1′,6′-gh:2″,1″,6″-kl:2″′,l″′,6″′-na][1,3,5,8,10,12]hexaazacyclotetradecine iron(III) chloride, (phen2N2)FeCl. HR MALDI-TOF (POPOP matrix): m/z 440.1061 ([M – Cl]+, calc. for C24H12FeN6: 440.0473), 475.1023 ([M]+, calc. for C24H12ClFeN6: 475.0161). UV–Vis (DMSO): λmax = 288 nm (ε = 11,649 L mol−L cm−c), 302 (11,932), 319 (10,284), 338 (5,892), 366 (5,411), 400 (4,477), 429 (3,105), 459 (1,942). 57Fe Mössbauer (90 K): δ = 0.39 mm s−1, |ΔEQ| = 3.06 mm s−1. A satisfactory elemental analysis for (phen2N2)FeCl could not be obtained due the presence of unreacted Fe salts, primarily FeCl3 and Fe2Cl6•(DMF)350. Fe2Cl6•(DMF)3 is synthesized by exposing FeCl3 as a solution in ether to DMF, resulting in a solid that can be collected by filtration. The reaction conditions described above should be conducive to forming Fe2Cl6•(DMF)3, which explains the origin of the minor impurity. Elemental analysis results matched upon the incorporation of 16% of Fe2Cl6•(DMF)3: Anal. Calcd. for (phen2N2)FeCl + 0.16(Fe2Cl6•(DMF)3 = (C24H12ClFeN6 + 0.16(C9H21Cl6Fe2N3O3): C, 53.30; H, 2.76; N, 15.89. Found: C, 52.96; H, 2.77; N, 15.93. This accounts for the additional doublet observed in the 57Fe Mössbauer spectrum (see Supplementary Fig. 5, middle) which is similar to that of hydrated FeCl3 adsorbed on carbon105,106. Exhaustive washing with common anhydrous solvents like ether and CH2Cl2 failed to remove residual Fe salts. This is attributed to the extreme insolubility of the complex that prevents the effective removal of trapped Fe salts. Indeed, even in highly polar solvents such as DMF, DMSO, and HMPA visible dissolution of (phen2N2)FeCl is only observed at temperatures in excess of ~150 °C.

Synthesis of [(phen2N2)Fe]2O

In a typical preparation, a sample of (phen2N2)FeCl was placed in a cellulose extraction thimble and loaded into a Soxhlet apparatus. After placing the apparatus under inert atmosphere by purging extensively with argon, the sample was washed continuously with hot ethanol for 48 h. Afterwards, the sample was removed from the Soxhlet apparatus and dried in an oven overnight to remove trace water and volatile solvents, furnishing (μ-Oxo)bis[(1,14:7,8-Diethenotetrapyrido[2,1,6-de:2′,1′,6′-gh:2″,1″,6″-kl:2″′,l″′,6″′-na][1,3,5,8,10,12]hexa-azacyclotetradecine)iron(III)], [(phen2N2)Fe]2O. XPS N:Fe ratio: 6.3:1. 57Fe Mössbauer (90 K): δ = 0.45 mm s−1, |ΔEQ| = 0.87 mm s−1. HR MALDI-TOF (POPOP matrix): m/z 440.0975 ([M – C24H12FeN6O]+, calc. for C24H12FeN6: 440.0473). A satisfactory elemental analysis for [(phen2N2)Fe]2O could not be obtained due to the presence of trace impurities, which were presumably carried through the metalation and Soxhlet procedures. Similar solubility issues as (phen2N2)FeCl above trap trace impurities that are not easily removed by washing.

Synthesis of [(OEP)Fe]2O

Octaethylporphinatoiron(III) chloride dissolved in CH2Cl2 was vigorously shaken in a separatory funnel with aqueous 2 M NaOH. After separating the layers, the organic layer was washed with water, dried over MgSO4 and filtered. After washing the MgSO4 with CH2Cl2, the combined organic layers were concentrated to dryness, resulting in a brown microcrystalline solid which was then dried at 60 °C for several hours to give (μ-Oxo)bis[(octaethylporphinato)iron(III)], [(OEP)Fe]2O. The Fe-O-Fe unit was identified by infrared spectroscopy with characteristic bands at 870 and 832 cm−1. These observed values are in line with those reported in the literature for [(OEP)Fe]2O55. 57Fe Mössbauer (90 K): δ = 0.41 mm s−1, |ΔEQ| = 0.67 mm s−1.

Synthesis of [(Pc)Fe]2O

0.502 g (0.884 mmol) iron(II) phthalocyanine was suspended in 150 mL THF and stirred open to air for 24 h. The solid is isolated by filtration and is washed with MeOH. After drying the solid in an oven at 60 °C, 0.457 g (90%) of (μ-Oxo)bis[(phthalocyaninato)iron(III)], [(Pc)Fe]2O, is obtained as a dark blue powder58,59. 57Fe Mössbauer (90 K): δ = 0.24 mm s−1, |ΔEQ| = 1.26 mm s−1.

Synthesis of (Pc)FeCl

10 g (78.05 mmol, 3.99 equiv.) phthalonitrile and 3.173 g (19.56 mmol) FeCl3 were mixed with 20 mL chloronaphthalene. The mixture was brought to reflux and stirred for 18 h. Afterwards, the solid was isolated by filtration and washed with acetone. The solid was dried in an oven at 60 °C to yield 10.891 g (92%) of iron(III) phthalocyanine chloride, (Pc)FeCl, as a dark green powder107. 57Fe Mössbauer (90 K): δ = 0.28 mm s−1, |ΔEQ| = 2.95 mm s−1.

Zero-field 57Fe Mössbauer spectroscopy

Zero-field 57Fe Mössbauer spectra were measured with a constant acceleration spectrometer (SEE Co., Minneapolis, MN) at 90 K. Solid samples (20–30 mg for molecular samples and 120 mg for Fe-N-C) were prepared by mixing each sample powder with Paratone-N oil. With the exception of the (phen2N2)FeCl sample, each sample was prepared outside the glovebox. The (phen2N2)FeCl sample was prepared similarly except the sample preparation process was carried out inside a nitrogen-filled glovebox and the sample was frozen with liquid nitrogen before handling outside the glovebox. All isomer shifts are reported relative to α-Fe metal at 298 K. All data were processed, fitted, and analyzed using an in-house software package for IGOR Pro 6 (Wavemetrics, Lake Oswego, OR).

X-ray photoelectron spectroscopy

XPS experiments were performed on ThermoFisher Aluminum K Alpha+ (ESCA) or ThermoFisher Nexsa X-ray spectrometer systems with monochromatic aluminum Kα X-ray sources (1486.68 eV). Samples for analysis were prepared by distributing a small amount of Au powder (for referencing) on conductive carbon tape and spreading the analyte on top. The analyte was mixed with the Au powder to allow for simultaneous detection of analyte and the Au powder. All experiments were run with the flood gun on to prevent sample charging. All data were collected using a 400 μm, 72 W focused X-ray beam at a base pressure of 2  × 10−7 millibar or lower. Survey scans were collected at a pass energy of 200 eV and step size of 1 eV. High-resolution scans were collected with a pass energy of 50 eV and a step size of 0.1 eV. All data were analyzed with the Thermo Avantage software package (v5.987). The Au 4f7/2 peak arising from the Au powder was assigned an energy of 84.0 eV and used as an internal binding energy reference for all spectra. In all cases the recorded spectral data were not modified with a smoothing algorithm. High-resolution spectra were fit by application of a Shirley-type (Smart) background and Gaussian/Lorentzian line-shapes of 30% Gaussian shape. The Simplex fitting algorithm was used in all cases.

XPS ratios were taken from survey spectra. We expect these values to be reliable because survey spectra were collected with a high pass energy (200 eV), relatively high step size (1 eV) and because the spectra display a high signal to noise ratio. The [(phen2N2)Fe]2O sample shows a substantial amount of residual chloride relative to iron. This is attributed to variation caused by the insoluble nature of (phen2N2)Fe complexes which allows small amounts of chloride salts to be carried through the metalation and Soxhlet procedures. A possible assignment in this case is a small amount of triethylammonium chloride, [Et3NH]Cl. For the O 1s XPS, the carbon tape gives rise to a set of background oxygen peaks including aromatic C = O (~531 eV, green), aliphatic C–O (~532 eV, blue) and aromatic C–O (~533 eV, yellow)108 that dominates the O 1s manifold. This background results from gaps in the microcrystalline molecular film that exposes the background carbon support.

X-ray absorption spectroscopy

XAS experiments were performed at the 10-BM beamline at the Advanced Photon Source (APS) at Argonne National Laboratory. All measurements were performed at the Fe K edge (7.112 keV) in transmission mode in fast scan from 250 eV below the edge to 550 eV above the edge. Samples were pressed into a stainless-steel sample holder. For catalysts containing 1 wt% Fe, ~12 mg was loaded. For catalysts containing 8–10 wt% Fe, ~1 mg diluted in boron nitride to reach a total of ~10 mg was loaded. The sample holder was placed in a leak-tight sample cell with gas flow capabilities and purged with He at room temperature. The cell was sealed and transferred to the beamline to be scanned.

The data were interpreted using WinXAS 3.1 software to find the coordination number (CN) and bond distance (R) using standard procedures. The phase and amplitude functions for Fe–N and Fe–O were extracted from theoretical Feff6 calculations. Theoretical phase and amplitude files were created for the Fe–N (CN = 1, R = 1.94 Å) and Fe–O (CN = 1, R = 1.99 Å) scattering pairs obtained from known reference compounds. Least squared fits of the first shell of r-space and isolated q-space were performed on the k2-weighted Fourier transform data over the range 2.71–10 Å−1 in each spectrum to fit the magnitude and imaginary components. The fits were calibrated using the Fe foil (CN = 8, R = 2.54 Å). During the fit of the Fe foil, the CN was fixed to 8 and an amplitude reduction factor (So2) of 0.64 was obtained. The So2 was fixed as 0.64 to fit all other EXAFS data. WinXAS software provides error calculations for each parameter, generated from a correlation matrix during the least squared fit. These values are on the order of +/−10% for the CN, +/−5% for R, and +/−0.0001 for the Debye-Waller factor (s2). The s2 stands for the mean square variation in the bond distances.

Computational details

All DFT calculations were performed using the ab-initio software package Q-Chem109, the meta-hybrid functional TPSSh110 and the basis set 6–31+G*111,112,113. To model solvation, the implicit solvation model IEF-PCM with a dielectric constant of 78.4 was used114. All molecular images were generated using the software package VESTA115. The geometries of (phen2N2)Fe(III)Cl and [(phen2N2)Fe(III)]+ were optimized with spin states S = 1/2, 3/2, and 5/2. The most stable spin state was found to be S = 3/2 in both cases.

General electrochemical methods

Sodium hydroxide (99.99%, semiconductor grade), potassium ferricyanide (ACS grade) and potassium sulfate (99.99%, semiconductor grade) were obtained from Sigma Aldrich and used as received. 5 wt% perfluorinated Nafion® resin solution was obtained from Ion Power Inc. and used as received. Aqueous electrolyte solutions were prepared with deionized water purified to a resistivity of 18.2 M Ω-cm using a Milliq water purification system (Millipore Corporation). Vulcan VXC72R carbon powders were obtained from Cabot Corporation and used as received. Glassy carbon disk electrodes were obtained from Pine Research Instrumentation, Inc. Hg/HgO and Hg/Hg2SO4 reference electrodes were obtained from CH Instruments, Inc. A titanium mesh was used as the counter electrode for all electrochemical experiments. The titanium counter was constructed of titanium wire (99.9%) and titanium gauze (40 mesh) obtained from Alfa Aesar and was treated with aqua regia prior to use.

All electrochemical experiments were conducted at ambient temperature using a Biologic VSP 16-channel potentiostat and a three-electrode electrochemical cell. In all cases, the Ti counter electrode was isolated from the working compartment by a porous glass frit. Hg/HgO and Hg/Hg2SO4 reference electrodes were used for all experiments conducted in alkaline and acidic aqueous electrolytes, respectively. The Hg/HgO reference was stored in 3 M NaOH solution between measurements. Electrode potentials measured in aqueous alkaline media were converted to the RHE scale using the following relationship: E(RHE) = E(Hg/HgO) + 0.094 V + 0.059*(pH) V. The Hg/Hg2SO4 electrode was stored in saturated K2SO4 solution between measurements. Electrode potentials measured in aqueous acidic media were converted to the RHE scale using the relationship: E(RHE) = E(Hg/Hg2SO4) + 0.65 V + 0.059*(pH) V. Reference electrodes were periodically checked against a pristine reference to ensure against potential drift.

Routine electrochemical measurements were performed with a 5 mm diameter glassy carbon disk working electrode rotated at 2000 rpm. All scan rates were 5 mV s−1 to allow for equilibration and to approximate steady state catalytic operation. Cyclic and linear sweep voltammograms were initiated at the open circuit potential. In all cases, the potential was swept in the negative direction. Solution resistance values were <10 Ω and were ignored. All voltammograms were recorded without iR compensation. Solutions were sparged for 10 min before each experiment with either N2 or O2 and for another 10 min upon changing between gases. During an experiment, the headspace of the cell was continually flushed with the working gas to minimize solution contamination by atmospheric gases. All experiments were conducted using 10 μL of catalyst ink dropcast onto a polished glassy carbon RDE. Catalytic onset potentials were taken to be the potential at which the observed current density reached –0.1 mA cm2 . Buffers used for the pH-dependence study of the (phen2N2)FeCl ink consisted of a modified Britton-Robinson buffer (50 mM each of NaHSO4, Na2HPO4 and B(OH)3) that was adjusted to the desired pH value with concentrated HClO4 or NaOH.

Preparation of Fe-N-C ink

Fe-N-C inks for use in electrochemical studies were prepared by sequentially adding CH2Cl2, EtOH, and 5 wt% Nafion solution to 11 mg Fe-N-C catalyst in a ratio of 7:2:1 to give a final volume of 1 mL and an Fe-N-C concentration of 11 mg mL−1. The resulting mixture was sonicated for 16 min to give the product ink. Inks were produced in 1 mL batches. Superior results in terms of carbon powder dispersion and ORR activity were obtained when CH2Cl2 was added to the precursor powder first, followed by EtOH and Nafion solution. The Fe-N-C data presented in Fig. 5 and Supplementary Fig. 25 was collected at an Fe-N-C concentration of 4.7 mg mL−1 in order to limit the double-layer capacitance, which can obscure redox peaks. See Supplementary Table 10 for nominal dropcast film mass loadings.

Preparation of (phen2N2Fe)Cl, (Pc)FeCl and (OEP)FeCl Inks

Inks for use in electrochemical studies were prepared by suspending ~1.1 mg mL−1 catalyst (either porphyrin- or (phen2N2)-based) in ~2.5 mg mL−1 Vulcan VXC72R carbon. CH2Cl2, EtOH and 5 wt% Nafion solution are added sequentially in a ratio of 7:2:1. The resulting mixtures were sonicated for 16 min to give the product inks. The inks were produced in 1 mL batches in all cases. Note that superior results in terms of carbon powder dispersion and ORR activity were obtained when CH2Cl2 was added to the solid precursor mixture first followed by EtOH and Nafion solution. See Supplementary Table 10 for nominal dropcast film mass loadings.

Rotating ring disk electrode voltammetry

RRDE voltammetry was performed with a Pine rotator using a ChangeDisk tip. RRDE experiments conducted in acidic media were performed with a platinum ring while experiments conducted in alkaline media were performed with a gold ring116. The Pt and Au rings were cleaned by cyclic voltammetry conducted at 50 mV s−1 over potential ranges of 1 to −0.8 V and 1.1 to −0.7 V, respectively, vs the Hg/Hg2SO4 reference in 0.1 M HClO4. The potential was swept over the appropriate range until the cyclic voltammograms overlaid exactly.

The proportion of H2O2 produced during ORR was quantified using the following relationship95:

$$\% {\mathrm{H}}_{2}{\mathrm{O}}_{2} = \frac{{100\left( {\frac{{2i_{{\mathrm{ring}}}}}{N}} \right)}}{{i_{{\mathrm{disk}}} + \left( {\frac{{i_{{\mathrm{ring}}}}}{N}} \right)}}$$
(3)

In this case, iring and idisk are the currents at the ring and disk electrodes, respectively and N is the collection efficiency. The number of electrons transferred as a function of applied potential was calculated using the following relationship117:

$$n_{{\mathrm{e}}-} = \frac{{4i_{{\mathrm{disk}}}}}{{i_{{\mathrm{disk}}} + \left( {\frac{{i_{{\mathrm{ring}}}}}{N}} \right)}}$$
(4)

The collection efficiency constant, N, was calculated at the end of each group of experiments under a given set of conditions by examining the Fe(III/II) couple via chronoamperometry. The ring was polarized at 1.5 V vs RHE while the disk was held at 0.1 V vs RHE and currents were monitored for 60 seconds. The current values over the last 10 s were averaged and taken as the values for iring and idisk. A 60 s chronoamperogram was also run with the ring as the working electrode to give the background oxidative current at 1.5 V vs RHE. Averaging the last 10 s of the background trace gave the value of iring0. Collection efficiency measurements were conducted using a blank glassy carbon disk. Fe2(SO4)3 and K3Fe(CN)6 were used as the redox agents for the collection efficiency measurements in acid and base, respectively. The collection efficiency was calculated using Eq. (5) and found to be 10–11% at the Pt ring and 22–23% at the Au ring116:

$$N = \frac{{i_{{\mathrm{ring}}}-i_{{\mathrm{ring}}0}}}{{i_{{\mathrm{disk}}}}}$$
(5)

Since calculated %H2O2 values are unreliable when disk currents are small (near the ORR onset region), each %H2O2 trace is shown starting where dependable data are available and noise in the measurement has been minimized. Although each catalyst is distinct, this point was located between 50–100 mV past the ORR onset potential in all cases.

Data availability

Data generated or analysed during this study are included in this article and/or its supplementary information files. Raw data are available from the authors on request.

References

  1. 1.

    Seh, Z. W. et al. Combining theory and experiment in electrocatalysis: insights into materials design. Science 355, eaad4998 (2017).

    PubMed  Article  Google Scholar 

  2. 2.

    Shao, M., Chang, Q., Dodelet, J.-P. & Chenitz, R. Recent advances in electrocatalysts for oxygen reduction reaction. Chem. Rev. 116, 3594–3657 (2016).

    CAS  PubMed  Article  Google Scholar 

  3. 3.

    Sealy, C. The problem with platinum. Mater. Today 11, 65–68 (2008).

    CAS  Article  Google Scholar 

  4. 4.

    Steele, B. C. H. & Heinzel, A. Materials for fuel-cell technologies. Nature 414, 345–352 (2001).

    ADS  CAS  PubMed  Article  Google Scholar 

  5. 5.

    Gasteiger, H. A., Kocha, S. S., Sompalli, B. & Wagner, F. T. Activity benchmarks and requirements for Pt, Pt-alloy, and non-Pt oxygen reduction catalysts for PEMFCs. Appl. Catal. B Environ. 56, 9–35 (2005).

    CAS  Article  Google Scholar 

  6. 6.

    Kinumoto, T. et al. Stability of Pt-catalyzed highly oriented pyrolytic graphite against hydrogen peroxide in acid solution. J. Electrochem. Soc. 153, A58–A63 (2006).

    CAS  Article  Google Scholar 

  7. 7.

    Ramaswamy, N., Hakim, N. & Mukerjee, S. Degradation mechanism study of perfluorinated proton exchange membrane under fuel cell operating conditions. Electrochim. Acta 53, 3279–3295 (2008).

    CAS  Article  Google Scholar 

  8. 8.

    Sethuraman, V. A., Weidner, J. W., Haug, A. T., Motupally, S. & Protsailo, L. V. Hydrogen peroxide formation rates in a PEMFC anode and cathode. J. Electrochem. Soc. 155, B50–B57 (2008).

    CAS  Article  Google Scholar 

  9. 9.

    Wu, G. et al. Performance durability of polyaniline-derived non-precious cathode catalysts. ECS Trans. 25, 1299–1311 (2009).

    Article  Google Scholar 

  10. 10.

    Jasinski, R. A new fuel cell cathode catalyst. Nature 201, 1212–1213 (1964).

    ADS  CAS  Article  Google Scholar 

  11. 11.

    Jasinski, R. Cobalt phthalocyanine as a fuel cell cathode. J. Electrochem. Soc. 112, 526 (1965).

    ADS  CAS  Article  Google Scholar 

  12. 12.

    Jaouen, F. et al. Toward platinum group metal-free catalysts for hydrogen/air proton-exchange membrane fuel cells. Johns. Matthey Technol. Rev. 62, 231–255 (2018).

    CAS  Article  Google Scholar 

  13. 13.

    Lefèvre, M., Proietti, E., Jaouen, F. & Dodelet, J.-P. Iron-based catalysts with improved oxygen reduction activity in polymer electrolyte fuel cells. Science 324, 71–74 (2009).

    ADS  Article  CAS  Google Scholar 

  14. 14.

    Bezerra, C. W. B. et al. A review of Fe–N/C and Co–N/C catalysts for the oxygen reduction reaction. Electrochim. Acta 53, 4937–4951 (2008).

    CAS  Article  Google Scholar 

  15. 15.

    Liu, W. et al. Discriminating catalytically active FeNx species of atomically dispersed Fe–N–C catalyst for selective oxidation of the C–H bond. J. Am. Chem. Soc. 139, 10790–10798 (2017).

    CAS  PubMed  Article  Google Scholar 

  16. 16.

    Kramm, U. I. et al. Structure of the catalytic sites in Fe/N/C-catalysts for O2-reduction in PEM fuel cells. Phys. Chem. Chem. Phys. 14, 11673–11688 (2012).

    CAS  PubMed  PubMed Central  Article  Google Scholar 

  17. 17.

    Bouwkamp-Wijnoltz, A. L. et al. On active-site heterogeneity in pyrolyzed carbon-supported iron porphyrin catalysts for the electrochemical reduction of oxygen: an in situ Mössbauer study. J. Phys. Chem. B 106, 12993–13001 (2002).

    CAS  Article  Google Scholar 

  18. 18.

    Bron, M., Radnik, J., Fieber-Erdmann, M., Bogdanoff, P. & Fiechter, S. EXAFS, XPS and electrochemical studies on oxygen reduction catalysts obtained by heat treatment of iron phenanthroline complexes supported on high surface area carbon black. J. Electroanal. Chem. 535, 113–119 (2002).

    CAS  Article  Google Scholar 

  19. 19.

    Zitolo, A. et al. Identification of catalytic sites for oxygen reduction in iron- and nitrogen-doped graphene materials. Nat. Mater. 14, 937–942 (2015).

    ADS  CAS  PubMed  Article  Google Scholar 

  20. 20.

    Jaouen, F., Marcotte, S., Dodelet, J.-P. & Lindbergh, G. Oxygen reduction catalysts for polymer electrolyte fuel cells from the pyrolysis of iron acetate adsorbed on various carbon supports. J. Phys. Chem. B 107, 1376–1386 (2003).

    CAS  Article  Google Scholar 

  21. 21.

    Dodelet, J.-P. In Electrocatalysis in Fuel Cells (ed. Shao, M.) vol. 9, 271–338 (Springer London, 2013).

  22. 22.

    Holst-Olesen, K., Silvioli, L., Rossmeisl, J. & Arenz, M. Enhanced oxygen reduction reaction on Fe/N/C catalyst in acetate buffer electrolyte. ACS Catal. 9, 3082–3089 (2019).

    CAS  Article  Google Scholar 

  23. 23.

    Leonard, N. D. et al. Deconvolution of utilization, site density, and turnover frequency of Fe–nitrogen–carbon oxygen reduction reaction catalysts prepared with secondary N-precursors. ACS Catal. 8, 1640–1647 (2018).

    CAS  Article  Google Scholar 

  24. 24.

    Strickland, K. et al. Highly active oxygen reduction non-platinum group metal electrocatalyst without direct metal–nitrogen coordination. Nat. Commun. 6, 7343 (2015).

    ADS  CAS  PubMed  PubMed Central  Article  Google Scholar 

  25. 25.

    Varnell, J. A. et al. Identification of carbon-encapsulated iron nanoparticles as active species in non-precious metal oxygen reduction catalysts. Nat. Commun. 7, 12582 (2016).

    ADS  CAS  PubMed  PubMed Central  Article  Google Scholar 

  26. 26.

    Jia, Q. et al. Spectroscopic insights into the nature of active sites in iron–nitrogen–carbon electrocatalysts for oxygen reduction in acid. Nano Energy 29, 65–82 (2016).

    CAS  Article  Google Scholar 

  27. 27.

    Glibin, V. P. & Dodelet, J.-P. Thermodynamic stability in acid media of FeN4-based catalytic sites used for the reaction of oxygen reduction in PEM fuel cells. J. Electrochem. Soc. 164, F948–F957 (2017).

    CAS  Article  Google Scholar 

  28. 28.

    Lefèvre, M., Dodelet, J. P. & Bertrand, P. O2 reduction in PEM fuel cells: activity and active site structural information for catalysts obtained by the pyrolysis at high temperature of Fe precursors. J. Phys. Chem. B 104, 11238–11247 (2000).

    Article  CAS  Google Scholar 

  29. 29.

    Pels, J. R., Kapteijn, F., Moulijn, J. A., Zhu, Q. & Thomas, K. M. Evolution of nitrogen functionalities in carbonaceous materials during pyrolysis. Carbon 33, 1641–1653 (1995).

    CAS  Article  Google Scholar 

  30. 30.

    Li, H., Zhang, Z., Dou, M. & Wang, F. Towards high-performance electrocatalysts for oxygen reduction: inducing atomic-level reconstruction of Fe-Nx site for atomically dispersed Fe/N-doped hierarchically porous carbon. Chem. Eur. J. 24, 8848–8856 (2018).

    CAS  PubMed  Article  Google Scholar 

  31. 31.

    Schulenburg, H. et al. Catalysts for the oxygen reduction from heat-treated iron(iii) tetramethoxyphenylporphyrin chloride: structure and stability of active sites. J. Phys. Chem. B 107, 9034–9041 (2003).

    CAS  Article  Google Scholar 

  32. 32.

    Artyushkova, K. et al. Density functional theory calculations of XPS binding energy shift for nitrogen-containing graphene-like structures. Chem. Commun. 49, 2539–2541 (2013).

    CAS  Article  Google Scholar 

  33. 33.

    Strauss, S. H. et al. Comparison of the molecular and electronic structures of (2,3,7,8,12,13,17,18-octaethylporphyrinato)iron(ii) and (trans-7,8-dihydro-2,3,7,8,12,13,17,18-octaethylporphyrinato)iron(ii). J. Am. Chem. Soc. 107, 4207–4215 (1985).

    CAS  Article  Google Scholar 

  34. 34.

    Dale, B. W., Williams, R. J. P., Edwards, P. R. & Johnson, C. E. S = 1 spin state of divalent iron. II. A Mössbauer‐effect study of phthalocyanine iron (ii). J. Chem. Phys. 49, 3445 (1968).

    ADS  CAS  Article  Google Scholar 

  35. 35.

    Koslowski, U. I., Abs-Wurmbach, I., Fiechter, S. & Bogdanoff, P. Nature of the catalytic centers of porphyrin-based electrocatalysts for the ORR: a correlation of kinetic current density with the site density of Fe−N4 centers. J. Phys. Chem. C. 112, 15356–15366 (2008).

    CAS  Article  Google Scholar 

  36. 36.

    Chenitz, R. et al. A specific demetalation of Fe–N4 catalytic sites in the micropores of NC_Ar + NH3 is at the origin of the initial activity loss of the highly active Fe/N/C catalyst used for the reduction of oxygen in PEM fuel cells. Energy Environ. Sci. 11, 365–382 (2018).

    CAS  Article  Google Scholar 

  37. 37.

    Wan, X. et al. Synthesis and active site identification of Fe−N−C single-atom catalysts for the oxygen reduction reaction. ChemElectroChem 6, 304–315 (2019).

    CAS  Article  Google Scholar 

  38. 38.

    Workman, M. J., Serov, A., Tsui, L., Atanassov, P. & Artyushkova, K. Fe–N–C catalyst graphitic layer structure and fuel cell performance. ACS Energy Lett. 2, 1489–1493 (2017).

    CAS  Article  Google Scholar 

  39. 39.

    Jiang, R. et al. Edge-site engineering of atomically dispersed Fe–N4 by selective C–N bond cleavage for enhanced oxygen reduction reaction activities. J. Am. Chem. Soc. 140, 11594–11598 (2018).

    CAS  PubMed  Article  Google Scholar 

  40. 40.

    Liu, D. et al. In situ trapped high-density single metal atoms within graphene: iron-containing hybrids as representatives for efficient oxygen reduction. Nano Res. 11, 2217–2228 (2018).

    CAS  Article  Google Scholar 

  41. 41.

    Chung, H. T. et al. Direct atomic-level insight into the active sites of a high-performance PGM-free ORR catalyst. Science 357, 479–484 (2017).

    ADS  CAS  PubMed  Article  Google Scholar 

  42. 42.

    Fei, H. et al. General synthesis and definitive structural identification of MN4C4 single-atom catalysts with tunable electrocatalytic activities. Nat. Catal. 1, 63–72 (2018).

    CAS  Article  Google Scholar 

  43. 43.

    Lovecchio, F. V., Gore, E. S. & Busch, D. H. Oxidation and reduction behavior of macrocyclic complexes of nickel. Electrochemical and electron spin resonance studies. J. Am. Chem. Soc. 96, 3109–3118 (1974).

    CAS  Article  Google Scholar 

  44. 44.

    van Baar, J. F., van Veen, J. A. R., van der Eijk, J. M., Peters, Th. J. & de Wit, N. Electrochemical oxidation of carbon monoxide with carbon-supported group VIII metal chelates: mechanistic aspects. Electrochim. Acta 27, 1315–1319 (1982).

    Article  Google Scholar 

  45. 45.

    Ogawa, S., Yamaguchi, T. & Gotoh, N. Preparation of a conjugated tautomer of 1,14:7,8-diethenotetrapyrido-[2,1,6-de:2′,1′,6′-gh:2″,1″,6″-kl:2‴,1‴,6‴na][1,3,5,8,10,12]hexa-azacyclotetradecine and its metal derivatives. J. Chem. Soc., Perkin Trans. 1, 976–978 (1974).

    Article  Google Scholar 

  46. 46.

    Cheng, C.-C., Kuo, Y.-N., Chuang, K.-S., Luo, C.-F. & Wang, W. J. A new CoII complex as a bulge-specific probe for. Dna. Angew. Chem. Int. Ed. 38, 1255–1257 (1999).

    CAS  Article  Google Scholar 

  47. 47.

    Costamagna, J. et al. Precursors of aza-macrocycles: characterization of substituted phenanthrolines and related bases. Crystal and molecular structure of dichloro-d i-n-butyl(2,2′,6,6′-bipyrimidine)tin(iv). Pure Appl. Chem. 65, 1521–1526 (1993).

    CAS  Article  Google Scholar 

  48. 48.

    Kramm, U. I. et al. On an easy way to prepare metal–nitrogen doped carbon with exclusive presence of MeN4-type sites active for the ORR. J. Am. Chem. Soc. 138, 635–640 (2016).

    CAS  PubMed  Article  Google Scholar 

  49. 49.

    Ogawa, S. Preparation of macrocyclic compounds by thermal dimerization of 1,10-phenanthroline derivatives. J. Chem. Soc., Perkin Trans. 1, 214–216 (1977).

    Article  Google Scholar 

  50. 50.

    White, A. D. Iron(III) Chloride-Dimethylformamide. In Encyclopedia of Reagents for Organic Synthesis, https://doi.org/10.1002/047084289X.ri058 (2001).

  51. 51.

    Kastner, M. E., Scheidt, W. R., Mashiko, T. & Reed, C. A. Molecular structure of diaquo-ɑ,β,ɣ,δ-tetraphenylporphinatoiron(III) perchlorate and perchlorato-ɑ,β,ɣ,δ-tetraphenylporphinatoiron(III). Two new structural types for iron(III) porphyrins. J. Am. Chem. Soc. 100, 666–667 (1978).

    CAS  Article  Google Scholar 

  52. 52.

    Reed, C. A. et al. The missing heme spin state and a model for cytochrome c′. The mixed S = 3/2, 5/2 intermediate spin ferric porphyrin: perchlorato(meso-tetraphenylporphinato)iron(III). J. Am. Chem. Soc. 101, 2948–2958 (1979).

    CAS  Article  Google Scholar 

  53. 53.

    Dolphin, D. H., Sams, J. R. & Tsin, T. Bik Intermediate-spin (S = 3/2) porphyrinatoiron(III) complexes. Inorg. Chem. 16, 711–713 (1977).

    CAS  Article  Google Scholar 

  54. 54.

    Sams, J. R. & Tsin, T. B. Mössbauer Spectroscopy of Iron Porphyrins. Porphyrins https://doi.org/10.1016/B978-0-12-220104-2.50016-8 (1979).

  55. 55.

    Cheng, B. et al. An unusual near-eclipsed porphyrin ring orientation in two crystalline forms of (μ-oxo)bis[(octaethylporphinato)iron(III)]. Structural and molecular mechanics studies. Inorg. Chem. 34, 102–110 (1995).

    CAS  Article  Google Scholar 

  56. 56.

    Sinha, S., Aaron, M. S., Blagojevic, J. & Warren, J. J. Electrocatalytic dioxygen reduction by carbon electrodes noncovalently modified with iron porphyrin complexes: enhancements from a single proton relay. Chem. Eur. J. 21, 18072–18075 (2015).

    CAS  PubMed  Article  Google Scholar 

  57. 57.

    Götz, R., Ly, H. K., Wrzolek, P., Schwalbe, M. & Weidinger, I. M. Surface enhanced resonance Raman spectroscopy of iron Hangman complexes on electrodes during electrocatalytic oxygen reduction: advantages and problems of common drycast methods. Dalton Trans. 46, 13220–13228 (2017).

    PubMed  Article  Google Scholar 

  58. 58.

    Ercolani, C., Gardini, M., Monacelli, F., Pennesi, G. & Rossi, G. Interaction of (phthalocyaninato)iron(II) with molecular oxygen: synthesis and characterization of two different crystalline forms of (.mu.-oxo)bis[(phthalocyaninato)iron(III)]. Inorg. Chem. 22, 2584–2589 (1983).

    CAS  Article  Google Scholar 

  59. 59.

    Ercolani, C., Gardini, M., Murray, K. S., Pennesi, G. & Rossi, G. Crystalline isomerism in (.mu.-oxo)bis[(phthalocyaninato)iron(III)]: further characterization of the isomer having a linear or quasi-linear Fe-O-Fe bond system (.mu.-oxo(2)). Inorg. Chem. 25, 3972–3976 (1986).

    CAS  Article  Google Scholar 

  60. 60.

    Zhang, Z., Sun, J., Wang, F. & Dai, L. Efficient oxygen reduction reaction (ORR) catalysts based on single iron atoms dispersed on a hierarchically structured porous carbon framework. Angew. Chem. Int. Ed. 57, 9038–9043 (2018).

    CAS  Article  Google Scholar 

  61. 61.

    Lin, L., Zhu, Q. & Xu, A.-W. Noble-metal-free Fe–N/C catalyst for highly efficient oxygen reduction reaction under both alkaline and acidic conditions. J. Am. Chem. Soc. 136, 11027–11033 (2014).

    CAS  PubMed  Article  Google Scholar 

  62. 62.

    Karweik, D. H. & Winograd, N. Nitrogen charge distributions in free-base porphyrins, metalloporphyrins, and their reduced analogs observed by x-ray photoelectron spectroscopy. Inorg. Chem. 15, 2336–2342 (1976).

    CAS  Article  Google Scholar 

  63. 63.

    Lavallee, D. K., Brace, J. & Winograd, N. X-ray photoelectron spectra of N-methyltetraphenylporphyrins: evidence for a correlation of binding energies with metal-nitrogen bond distances. Inorg. Chem. 18, 1776–1780 (1979).

    CAS  Article  Google Scholar 

  64. 64.

    Muralidharan, S. & Hayes, R. G. Intense satellites in the N 1s X-ray photoelectron spectra of certain metalloporphyrins. J. Am. Chem. Soc. 102, 5106–5107 (1980).

    CAS  Article  Google Scholar 

  65. 65.

    Nemykin, V. N. et al. Metal-free and transition-metal tetraferrocenylporphyrins part 1: synthesis, characterization, electronic structure, and conformational flexibility of neutral compounds. Dalton Trans. 4233–4246 (2008).

  66. 66.

    Jia, H., Sun, Z., Jiang, D., Yang, S. & Du, P. An iron porphyrin-based conjugated network wrapped around carbon nanotubes as a noble-metal-free electrocatalyst for efficient oxygen reduction reaction. Inorg. Chem. Front. 3, 821–827 (2016).

    CAS  Article  Google Scholar 

  67. 67.

    Ouedraogo, G. V., Benlian, D. & Porte, L. X‐ray photoelectron spectroscopy of phthalocyanine compounds. J. Chem. Phys. 73, 642 (1980).

    ADS  CAS  Article  Google Scholar 

  68. 68.

    Åhlund, J. et al. The electronic structure of iron phthalocyanine probed by photoelectron and x-ray absorption spectroscopies and density functional theory calculations. J. Chem. Phys. 125, 034709 (2006).

    ADS  Article  CAS  Google Scholar 

  69. 69.

    Grosvenor, A. P., Kobe, B. A., Biesinger, M. C. & McIntyre, N. S. Investigation of multiplet splitting of Fe 2p XPS spectra and bonding in iron compounds. Surf. Interface Anal. 36, 1564–1574 (2004).

    CAS  Article  Google Scholar 

  70. 70.

    Jia, Q. et al. Experimental observation of redox-induced Fe–N switching behavior as a determinant role for oxygen reduction activity. ACS Nano 9, 12496–12505 (2015).

    CAS  PubMed  PubMed Central  Article  Google Scholar 

  71. 71.

    Sa, Y. J. et al. A general approach to preferential formation of active Fe–Nx sites in Fe–N/C electrocatalysts for efficient oxygen reduction reaction. J. Am. Chem. Soc. 138, 15046–15056 (2016).

    CAS  PubMed  Article  Google Scholar 

  72. 72.

    Colomban, C. et al. Synthesis and characterization of μ-nitrido, μ-carbido and μ-oxo dimers of iron octapropylporphyrazine. Dalton Trans. 44, 2240–2251 (2015).

    CAS  PubMed  Article  Google Scholar 

  73. 73.

    Lee, H. M., Olmstead, M. M., Gross, G. G. & Balch, A. L. Cocrystallization of binuclear iron(III) porphyrins with C60: bending of μ-O{FeIII(octaethylporphyrin)} and the first structure of the iron(III) octaethyloxophlorin dimer. Cryst. Growth Des. 3, 691–697 (2003).

    CAS  Article  Google Scholar 

  74. 74.

    Westre, T. E. et al. A multiplet analysis of Fe K-edge 1s → 3d pre-edge features of iron complexes. J. Am. Chem. Soc. 119, 6297–6314 (1997).

    CAS  Article  Google Scholar 

  75. 75.

    Palmer, S. M. et al. Preparation, structures, and physical properties of two products from the iodination of (phthalocyaninato)iron(II). Inorg. Chem. 24, 2040–2046 (1985).

    CAS  Article  Google Scholar 

  76. 76.

    Janczak, J., Kubiak, R. & Hahn, F. A neutral molecule of I2 as a bridge for dimerization of iodine iron(III) phthalocyanine. Inorg. Chim. Acta 287, 101–104 (1999).

    CAS  Article  Google Scholar 

  77. 77.

    Salimi, A., MamKhezri, H., Hallaj, R. & Zandi, S. Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: application to chlorate, bromate and iodate detection. Electrochim. Acta 52, 6097–6105 (2007).

    CAS  Article  Google Scholar 

  78. 78.

    He, Q. et al. Molecular catalysis of the oxygen reduction reaction by iron porphyrin catalysts tethered into Nafion layers: An electrochemical study in solution and a membrane-electrode-assembly study in fuel cells. J. Power Sources 216, 67–75 (2012).

    ADS  CAS  Article  Google Scholar 

  79. 79.

    Alsudairi, A. et al. Resolving the Iron Phthalocyanine Redox Transitions for ORR Catalysis in Aqueous Media. J. Phys. Chem. Lett. 8, 2881–2886 (2017).

    CAS  PubMed  Article  Google Scholar 

  80. 80.

    Zhang, L., Song, C., Zhang, J., Wang, H. & Wilkinson, D. P. Temperature and pH dependence of oxygen reduction catalyzed by iron fluoroporphyrin adsorbed on a graphite electrode. J. Electrochem. Soc. 152, A2421–A2426 (2005).

    CAS  Article  Google Scholar 

  81. 81.

    Jackson, M. N., Pegis, M. L. & Surendranath, Y. Graphite-conjugated acids reveal a molecular framework for proton-coupled electron transfer at electrode surfaces. ACS Cent. Sci. 5, 831–841 (2019).

    CAS  PubMed  PubMed Central  Google Scholar 

  82. 82.

    Luo, F. et al. Accurate evaluation of active-site density (SD) and turnover frequency (TOF) of PGM-free metal–nitrogen-doped carbon (MNC) electrocatalysts using CO cryo adsorption. ACS Catal. 9, 4841–4852 (2019).

    CAS  Article  Google Scholar 

  83. 83.

    Asset, T. & Atanassov, P. Iron-Nitrogen-Carbon Catalysts for Proton Exchange Membrane. Fuel Cells Joule 4, 33–44 (2020).

    CAS  Google Scholar 

  84. 84.

    Tylus, U. et al. Elucidating oxygen reduction active sites in pyrolyzed metal–nitrogen coordinated non-precious-metal electrocatalyst systems. J. Phys. Chem. C 118, 8999–9008 (2014).

    CAS  Article  Google Scholar 

  85. 85.

    Li, J. et al. Structural and mechanistic basis for the high activity of Fe–N–C catalysts toward oxygen reduction. Energy Environ. Sci. 9, 2418–2432 (2016).

    CAS  Article  Google Scholar 

  86. 86.

    Zúñiga, C. et al. Elucidating the mechanism of the oxygen reduction reaction for pyrolyzed Fe-N-C catalysts in basic media. Electrochem. Commun. 102, 78–82 (2019).

    Article  CAS  Google Scholar 

  87. 87.

    Jackson, M. N. et al. Strong electronic coupling of molecular sites to graphitic electrodes via pyrazine conjugation. J. Am. Chem. Soc. 140, 1004–1010 (2018).

    CAS  PubMed  Article  Google Scholar 

  88. 88.

    Fitzgerald, J. P., Haggerty, B. S., Rheingold, A. L., May, L. & Brewer, G. A. Iron octaethyltetraazaporphyrins: synthesis, characterization, coordination chemistry, and comparisons to related iron porphyrins and phthalocyanines. Inorg. Chem. 31, 2006–2013 (1992).

    CAS  Article  Google Scholar 

  89. 89.

    Kramm, U. I., Lefèvre, M., Larouche, N., Schmeisser, D. & Dodelet, J.-P. Correlations between mass activity and physicochemical properties of Fe/N/C catalysts for the ORR in PEM fuel cell via 57Fe Mössbauer spectroscopy and other techniques. J. Am. Chem. Soc. 136, 978–985 (2014).

    CAS  PubMed  Article  Google Scholar 

  90. 90.

    Chen, Y., Matanovic, I., Weiler, E., Atanassov, P. & Artyushkova, K. Mechanism of oxygen reduction reaction on transition metal–nitrogen–carbon catalysts: establishing the role of nitrogen-containing active sites. ACS Appl. Energy Mater. 1, 5948–5953 (2018).

    Article  CAS  Google Scholar 

  91. 91.

    Zagal, J. H. & Koper, M. T. M. Reactivity descriptors for the activity of molecular MN4 catalysts for the oxygen reduction reaction. Angew. Chem. Int. Ed. 55, 14510–14521 (2016).

    CAS  Article  Google Scholar 

  92. 92.

    Zagal, J. H. et al. A Possible Interpretation for the high catalytic activity of heat-treated non-precious metal Nx/C catalysts for O2 reduction in terms of their formal potentials. Electrochem. Solid-State Lett. 15, B90 (2012).

    CAS  Article  Google Scholar 

  93. 93.

    Bonakdarpour, A. et al. Impact of Loading in RRDE Experiments on Fe–N–C Catalysts: Two- or Four-Electron Oxygen Reduction? Electrochem. Solid-State Lett. 11, B105 (2008).

    CAS  Article  Google Scholar 

  94. 94.

    Muthukrishnan, A., Nabae, Y., Okajima, T. & Ohsaka, T. Kinetic approach to investigate the mechanistic pathways of oxygen reduction reaction on Fe-containing N-doped carbon catalysts. ACS Catal. 5, 5194–5202 (2015).

    CAS  Article  Google Scholar 

  95. 95.

    Rigsby, M. L., Wasylenko, D. J., Pegis, M. L. & Mayer, J. M. Medium effects are as important as catalyst design for selectivity in electrocatalytic oxygen reduction by iron–porphyrin complexes. J. Am. Chem. Soc. 137, 4296–4299 (2015).

    CAS  PubMed  Article  Google Scholar 

  96. 96.

    van Veen, J. A. R. et al. Oxygen reduction on transition-metal porphyrins in acid electrolyte I. Activity. Ber. Bunsenges. F.ür. Phys. Chem. 85, 693–700 (1981).

    Article  Google Scholar 

  97. 97.

    van Veen, J. A. R. & Colijn, H. A. Oxygen reduction on transition-metal porphyrins in acid electrolyte II. Stability. Ber. Bunsenges. F.ür. Phys. Chem. 85, 700–704 (1981).

    Article  Google Scholar 

  98. 98.

    Baranton, S., Coutanceau, C., Roux, C., Hahn, F. & Léger, J.-M. Oxygen reduction reaction in acid medium at iron phthalocyanine dispersed on high surface area carbon substrate: tolerance to methanol, stability and kinetics. J. Electroanal. Chem. 577, 223–234 (2005).

    CAS  Article  Google Scholar 

  99. 99.

    Choi, C. H. et al. The Achilles’ heel of iron-based catalysts during oxygen reduction in an acidic medium. Energy Environ. Sci. 11, 3176–3182 (2018).

    CAS  Article  Google Scholar 

  100. 100.

    Wang, W.-J., Sengul, A., Luo, C.-F., Kao, H.-C. & Cheng, Y.-H. Facile one-step synthesis of a thia-bridged bis-1,10-phenanthroline macrocycle. Tetrahedron Lett. 44, 7099–7101 (2003).

    CAS  Article  Google Scholar 

  101. 101.

    Krapcho, A. P., Sparapani, S., Leenstra, A. & Seitz, J. D. Displacement reactions of 2-chloro- and 2,9-dichloro-1,10-phenanthroline: synthesis of a sulfur-bridged bis-1,10-phenanthroline macrocycle and a 2,2′-amino-substituted-bis-1,10-phenanthroline. Tetrahedron Lett. 50, 3195–3197 (2009).

    CAS  Article  Google Scholar 

  102. 102.

    Guo, H. C., Zheng, R. H. & Jiang, H. J. Improved synthesis of 2,9-dichloro-1,10-phenanthroline. Org. Prep. Proced. Int. 44, 392–396 (2012).

    CAS  Article  Google Scholar 

  103. 103.

    Annibale, V. T., Batcup, R., Bai, T., Hughes, S. J. & Song, D. RuCp* complexes of ambidentate 4,5-diazafluorene derivatives: from linkage isomers to coordination-driven self-assembly. Organometallics 32, 6511–6521 (2013).

    CAS  Article  Google Scholar 

  104. 104.

    Ogawa, S., Yamaguchi, T. & Gotoh, N. Synthesis of a novel macrocyclic compound and of its copper complex. J. Chem. Soc., Chem. Commun. 577–578 (1972).

  105. 105.

    Vaishnava, P. P. & Montano, P. A. In situ Mössbauer spectroscopic study of iron III chloride intercalated in graphite under reaction conditions. J. Phys. Chem. Solids 43, 809–815 (1982).

    ADS  CAS  Article  Google Scholar 

  106. 106.

    Schlögl, R. & Jones, W. On the structure and properties of iron halide–graphite intercalates: a comparison of the reactivity of free and graphite-intercalated iron(III) chloride. J. Chem. Soc., Dalton Trans. 1283–1292 (1984).

  107. 107.

    Kalz, W. & Homborg, H. Eisen(III)phthalocyanine: Darstellung und spektroskopische Charakterisierung von [Fe(OR)2Pc(—2)]− (R = H, CH3, C2H5, (CH3)2CH, (CH3)3C), (FePc(—2))2O und FeXPc(—2) (X = F, Cl, Br, I) Z. Für. Naturforsch. B 38, 470–484 (1983).

    Article  Google Scholar 

  108. 108.

    Ganguly, A., Sharma, S., Papakonstantinou, P. & Hamilton, J. Probing the thermal deoxygenation of graphene oxide using high-resolution in situ X-ray-based spectroscopies. J. Phys. Chem. C 115, 17009–17019 (2011).

    CAS  Article  Google Scholar 

  109. 109.

    Shao, Y. et al. Advances in molecular quantum chemistry contained in the Q-Chem 4 program package. Mol. Phys. 113, 184–215 (2015).

    ADS  CAS  Article  Google Scholar 

  110. 110.

    Staroverov, V. N., Scuseria, G. E., Tao, J. & Perdew, J. P. Comparative assessment of a new nonempirical density functional: molecules and hydrogen-bonded complexes. J. Chem. Phys. 119, 12129 (2003).

    ADS  CAS  Article  Google Scholar 

  111. 111.

    Hehre, W. J., Ditchfield, R. & Pople, J. A. Self-consistent molecular orbital methods. XII. Further extensions of Gaussian-type basis sets for use in molecular orbital studies of organic molecules. J. Chem. Phys. 56, 2257 (1972).

    ADS  CAS  Article  Google Scholar 

  112. 112.

    Ditchfield, R., Hehre, W. J. & Pople, J. A. Self-consistent molecular-orbital methods. IX. An extended Gaussian-type basis for molecular-orbital studies of organic molecules. J. Chem. Phys. 54, 724 (1971).

    ADS  CAS  Article  Google Scholar 

  113. 113.

    Clark, T., Chandrasekhar, J., Spitznagel, G. W. & Schleyer, P. V. R. Efficient diffuse function-augmented basis sets for anion calculations. III. The 3-21+G basis set for first-row elements, Li-F. J. Comput. Chem. 4, 294–301 (1983).

    CAS  Article  Google Scholar 

  114. 114.

    Cances, E., Mennucci, B. & Tomasi, J. A new integral equation formalism for the polarizable continuum model: theoretical background and applications to isotropic and anisotropic dielectrics. J. Chem. Phys. 107, 3032 (1997).

    ADS  CAS  Article  Google Scholar 

  115. 115.

    Momma, K. & Izumi, F. VESTA: a three-dimensional visualization system for electronic and structural analysis. J. Appl. Crystallogr. 41, 653–658 (2008).

    CAS  Article  Google Scholar 

  116. 116.

    Zhou, R., Zheng, Y., Jaroniec, M. & Qiao, S.-Z. Determination of the electron transfer number for the oxygen reduction reaction: from theory to experiment. ACS Catal. 6, 4720–4728 (2016).

    CAS  Article  Google Scholar 

  117. 117.

    Song, C. & Zhang, J. In PEM Fuel Cell Electrocatalysts and Catalyst Layers (ed. Zhang, J.) 89–134 (Springer London, 2008).

Download references

Acknowledgements

This research was primarily supported as part of the Center for Molecular Electrocatalysis, an Energy Frontier Research Center funded by the U.S. Department of Energy (DOE), Office of Science, Basic Energy Sciences (BES). The computational work was supported by a seed grant from the MIT Energy Initiative. T. M.-R. acknowledges the Department of Defense (DoD) for a National Defense Science & Engineering Graduate Fellowship (NDSEG). Use of the Advanced Photon Source is supported by the U.S. Department of Energy, Office of Science, and Office of Basic Energy Sciences, under Contract DE-AC02–06CH11357. MRCAT operations are supported by the Department of Energy and the MRCAT member institutions. XPS investigations were performed at the Center for Nanoscale Systems (CNS), a member of the National Nanotechnology Coordinated Infrastructure Network (NNCI), which is supported by the National Science Foundation under NSF award no. 1541959. CNS is a part of Harvard University. Y.S. acknowledges the Sloan Foundation, Research Corporation for Science Advancement (Cottrell Scholar), and the Canadian Institute for Advanced Research (CIFAR Azrieli Global Scholar).

Author information

Affiliations

Authors

Contributions

Y.S. and T.M.-R. conceived of the research. T.M.-R. synthesized all compounds and catalysts, collected XPS and electrochemical data and analysed spectroscopic and electrochemical results. N.J.L. and J.T.M. collected and analysed the XAS data. A.T.W. and K.J.A. collected and analysed the 57Fe Mössbauer spectra. M.L.P. collected electrochemical data. N.D.R. and T.V.V. performed computations. Y.S. assisted with experimental design and data analysis. T.M.-R. and Y.S. wrote the manuscript with input from all authors.

Corresponding author

Correspondence to Yogesh Surendranath.

Ethics declarations

Competing interests

The authors declare the following competing financial interest(s): T.M.-R. and Y.S. are inventors on patent application 62/818,284, submitted by the Massachusetts Institute of Technology, that covers the hexaazamacrocycle iron complex and related catalyst ink described in this work.

Additional information

Peer review information Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work.

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Marshall-Roth, T., Libretto, N.J., Wrobel, A.T. et al. A pyridinic Fe-N4 macrocycle models the active sites in Fe/N-doped carbon electrocatalysts. Nat Commun 11, 5283 (2020). https://doi.org/10.1038/s41467-020-18969-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1038/s41467-020-18969-6

Further reading

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Search

Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing