Abstract
Hydrodynamic motion can generate a flux of electron-spin’s angular momentum via the coupling between fluid rotation and electron spins. Such hydrodynamic generation, called spin hydrodynamic generation (SHDG), has recently attracted attention in a wide range of fields, especially in spintronics. Spintronics deals with spin-mediated interconversion taking place on a micro or nano scale because of the spin-diffusion length scale. To be fully incorporated into the interconversion, SHDG physics should also be established in such a minute scale, where most fluids exhibit a laminar flow. Here, we report electric voltage generation due to the SHDG in a laminar flow of a liquid-metal mercury. The experimental results show a scaling rule unique to the laminar-flow SHDG. Furthermore, its energy conversion efficiency turns out to be about 105 greater than of the turbulent one. Our findings reveal that the laminar-flow SHDG is suitable to downsizing and to extend the coverage of fluid spintronics.
Introduction
A spin current, a flow of spin angular momentum, has enabled the interconversion among various kinds of physical entities such as electricity1,2, magnetization1,2, heat2,3,4,5,6, and mechanical motion like elastic motion7,8,9,10,11 and liquid motion12,13. Such spin-mediated interconversion is realized on a micro or nano scale1,2,14 and has been extensively studied in the field of spintronics. In this stream, recent study has revealed that fluid mechanical motion can also act as a constituent of this interconversion framework: spin hydrodynamic generation (SHDG). The SHDG has attracted much attention not only in the field of spintronics7,8,14,15,16,17,18 but also in a wide range of fields including nuclear physics19.
The origin of SHDG is the spin-rotation coupling, that is, the coupling between electron spin and local mechanical rotation of a fluid, or the vorticity, as shown in Fig. 1a. The driving force for the spin current induced by SHDG should strongly depend on vorticity distribution in a fluid flow. Therefore, SHDG is categorized reflecting the two typical regimes of fluid dynamics, that is, turbulent flow and laminar flow regimes. In a turbulent flow in a cylindrical channel (Fig. 1b), electromotive force should be generated only near the inner wall to give rise to an edge charge current. In a laminar flow (Fig. 1c), on the other hand, it is generated all over the cross section of a channel to give rise to a bulk one, where giant SHDG is expected. In micro or nano scale devices, a fluid flow usually becomes laminar20. Therefore, to make the most of SHDG in such devices, it is necessary to establish SHDG in laminar flow states.
a A schematic illustration of SHDG. v, ω, σ, jS, and ESHDG are the flow velocity, the vorticity, the spin polarization, the spin current caused by SHDG and the electromotive force caused by the inverse spin Hall effect in a liquid metal flow, respectively. b, c Geometries for SHDG in a turbulent flow (b) and in a laminar flow (c). Each illustration represents a cut-out part of a fluid flow in a cylindrical channel where SHDG is induced.
The mechanism of SHDG is as follows. When a liquid metal flows in a cylindrical channel, vorticity ω = ∇ × v is induced with spatial distribution shown in Fig. 1a, where v is the fluid velocity. In the presence of the spin-rotation coupling in a liquid metal, the vorticity gives rise to driving force for conduction-electron spin current12,13, and the gradient of the driving force causes a spin current,
where jS is a spin current, δμ is the driving potential for the spin current (the vector direction means the polarized direction σ), λ is the spin-diffusion length, and σ0 is the electric conductivity. ξ is the viscosity correction to the Newtonian fluid originating from the angular momentum conversion between the fluid vorticity and the electron spin due to SHDG12,13. The equation predicts that a spin current flows along the spatial gradient of ω with its polarized vector lying in the ω direction. The spin current generated in the liquid metal is then converted into an electric field, ESHDG, in the fluid flow direction via the inverse spin Hall effect in the liquid metal.
In a turbulent flow state (Fig. 1b), where SHDG has been first reported12, the vorticity gradient is located near the inner wall, meaning that the generation of ESHDG is limited near the inner wall. The area where SHDG occurs was estimated to be about 18% in a cross section of the fluid channel, and thus the rest area of the cross section does not contribute the generation but rather reduces the measured voltage due to short circuit currents. In this estimation, we considered one of the turbulent cases12, where a liquid Hg flows with the mean flow velocity of 2.1 m s−1 in a fluid channel whose inner diameter is 400 μm. The estimated area was determined as a cross section between the end of the viscous sublayer and the positions where ∇ω becomes one-tenth less than that at the end of the viscous sublayer, at which ∇ω is maximized. Here, the magnitude of ∇ω is proportional to \({\left(r-{r}_{0}\right)}^{-2}{\,}\)21, where r0 is the inner radius and r represents the radial position whose origin is at the center of the channel. This distribution stems from spatial distribution of v. In a turbulent flow state, v is almost constant in a channel but abruptly changes to zero very close to the inner wall, because momentum transfer perpendicular to the flow direction, origin of the turbulence, is suppressed due to the viscosity near the inner wall.
The localization of the generation is a major drawback of SHDG in turbulent flows from the viewpoint of energy efficiency. In a laminar flow (Fig. 1c), on the other hand, the spatial distribution of v pervades in a parabolic way, and thus ω gradient is created all over the cross section of a channel. According to the spatial distribution of v in a laminar flow (the Hagen–Poiseuille flow21), the magnitude of ∇ω is independent of r, meaning that ESHDG in a laminar flow can be generated all over the cross section of a fluid channel. This implies that SHDG can be much more efficient in a laminar flow than that in a turbulent flow. Therefore, SHDG in a laminar flow can be not only suitable for spin-driven micro or nano devices but also beneficial in the viewpoint of the energy conversion efficiency.
Here we show SHDG phenomenon in a laminar flow regime. In the present study, the laminar-flow SHDG is found to obey a unique scaling rule and continuously change to the turbulent one across a transition flow regime. Our major finding in the present study is that the energy conversion efficiency of the SHDG is exceedingly enhanced in the laminar flow regime.
Results
Description of fluid channel for SHDG measurement
Figure 2a shows a schematic illustration of the fluid channel used in the present study. In our study, we generate a flow of a liquid-metal mercury (Hg) in cylindrical quartz-glass channels (length L = 100 mm) by applying pulsed pressure, P. The inner diameter ϕ of the channels is 50, 70, 90, 112, and 126 μm to realize a laminar flow condition, and 200 μm to realize a transition flow condition. Two extra quartz-glass pipes (inner diameter: 1.0 mm, length: 100 mm) filled with Hg are used as electrodes, named electrode pipes shown in Fig. 2a. The electrode pipes are connected to liquid reservoirs near the inlet and the outlet of the fluid channel. The ends of the electrode pipes are placed in close proximity to each other to realize an isothermal condition and are connected to a nanovoltmeter, with which we measured the electric voltage difference Ve. This set-up enables us to avoid thermoelectric disturbance in the measurements because any thermoelectric voltage did not appear in the previous work12 when we made a temperature gradient along the channel by applying much greater heat at the end of the channel than that induced by the pulsed pressure. To prevent Hg from charging up electrically, Hg is connected to the ground at the inlet. Furthermore, this set-up enables us to avoid a charging effect, that is contact electrification22,23,24 at the channel wall, because it was experimentally confirmed12 that the voltage induced by the Hg flow is almost independent of the electrification property at the contact surface.
a A schematic illustration of the fluid channel used in the present study. A flow of liquid Hg in a quartz-glass fluid channel is induced by applying pulsed pressure, P. Ve denotes electric voltage difference between the ends of the channel. HI and LO denote the high and low terminals, respectively. b Time evolution of Ve for various values of P in the fluid channel whose inner diameter ϕ is 50 μm and the length L is 100 mm. c P dependences of the mean flow velocity v for the channel used in (b). v is estimated by averaging the data obtained from repetitive measurements. The experimental results are well reproduced by a relation for laminar flow states: v ∝ P. d P dependence of v for the channel of ϕ = 400 μm12, reproduced well by a relation for turbulent flow states: \(v\propto \sqrt{P}\). e v dependences of Ve for the channels of ϕ = 50 μm (blue filled circles) and ϕ = 400 μm (open circles)12. Ve (blue filled circle) is obtained by averaging the data obtained from repetitive measurements. In each measurement, Ve is estimated by taking a time average. The results obey the SHDG scaling law for laminar flow states: Ve ∝ v, totally different from that for turbulent one: Ve ∝ v2.
SHDG measurement in laminar flow regime
Figure 2b shows the time evolution of Ve measured for various values of P in a channel with ϕ = 50 μm. The Hg flow in the channel starts at time t = 10 s and ends at t = 50 s. A clear Ve signal appears when Hg is flowing. The magnitude of Ve increases with increasing P. Figure 2c shows the mean flow velocity v as a function of P in the channel. The linear relation between v and P (v ∝ P) indicates that the liquid flow in the measurement is in a laminar flow state according to a fluid theory, being consistent with the fact that the Reynolds number of the present flow, Re(=vϕ/ν), satisfies the laminar flow condition, 2 < Re < 110, where ν is the kinetic viscosity: ν = 1.2 × 10−7 m2s−1 for Hg12. On the other hand, in a turbulent condition, the P dependence of v exhibits square-root relations (\(v\propto \sqrt{P}\)) as shown in Fig. 2d. The result indicates that SHDG appears even in laminar flow condition.
In Fig. 2e, we plot the v dependence of Ve in the channels with ϕ = 50 μm and ϕ = 400 μm. The result for the ϕ-50-μm channel clearly illustrates that the Ve signal is proportional to v (Ve ∝ v) in the laminar flow condition. This relation in the laminar flow makes a sharp contrast with the turbulent condition12, where Ve is almost proportional to the square of the mean flow velocity, Ve ∝ v2, as shown by a result for the ϕ-400-μm channel (Fig. 2e). In fact, such linear dependence of Ve (Ve ∝ v) is very the feature predicted for SHDG in a laminar flow. The difference of the v dependence of Ve is due to the difference of spatial distribution of ∇ω between the laminar and turbulent conditions. The gradient of the vorticity in a laminar flow in a cylindrical channel is \(\partial {\omega }_{\theta }/\partial r=4v/{{r}_{0}}^{2}\) in a Hagen–Poiseuille flow condition, where θ is the azimuthal direction perpendicular to the flow and r0 ≡ ϕ/2. Therefore, in accordance with the SHDG theory13, electric voltage in a laminar flow is given by
where θSHE is the spin Hall angle. In Eq. (2), Ve is predicted to be proportional to v in a laminar flow, being consistent with the experimental result shown in Fig. 2e.
SHDG measurements for various values of channel inner diameter
To further examine the voltage signals, we measured Ve for various values of ϕ. Fig. 3a shows the ϕ dependence of v for various values of P. The solid curves for each pressure shown in Fig. 3a illustrate the relation \(v\propto {{r}_{0}}^{2}\), representing the theoretical prediction for laminar flows. Figure 3b shows the v dependence of Ve for channels with different ϕ values. The result shows that Ve increases linearly with v but with different slopes for the different ϕ values. However, as shown in Fig. 3c, all the different data collapse into a single curve when we plot them in a Ve – P scale. The result indicates that Ve is proportional to P with an identical slope independent of r0. Since \(v\propto {{r}_{0}}^{2}P\) is realized in the laminar (Hagen–Poiseuille) flow condition, as shown in Figs. 2c and 3a, Eq. (2) can be rewritten as Ve = CP, where C is a factor independent of r0, \(C=\frac{| e| }{{\sigma }_{0}\hbar \mu }\left({\theta }_{{\rm{SHE}}}{\lambda }^{2}\xi \right)\). Here, μ is the Newtonian viscosity. The result is well consistent with the prediction of SHDG in a laminar flow as shown in Eq. (2). By fitting the data in Fig. 3c with the equation of Ve = CP, the parameter θSHEλ2ξ is estimated to be 1.9 × 10−25 J s m−1. Here, we used parameters for Hg12, σ0 = 1.01 × 106 Ω−1 m−1 and μ = 1.6 × 10−3 J s m−3. The open circles shown in Fig. 3c are the data for the ϕ-400-μm channel, where the turbulent flow is realized. As shown in Fig. 3c, Ve induced by the SHDG for the turbulent flow is also proportional to P but slopes of the lines are different between the laminar and the turbulent flow, resulting from the difference in the velocity distributions.
a ϕ dependences of v for several values of P. Dimensional tolerance with respect to ϕ is 5 μm for the channels whose ϕ are 50, 112 and 126 μm, and 10 μm for the channels whose ϕ are 70 and 90 μm, respectively. The v data for each P is consistent with the relation for a laminar flow: \(v\propto {{r}_{0}}^{2}\), indicated by black curves. b v dependences of Ve for several values of ϕ. c P dependence of Ve. The open circles are the data of ϕ-400-μm channel12. The red solid line is the fit line obtained from the equation Ve = CP and the black solid line is an approximate line for the turbulent-flow SHDG. The values of v and Ve in (a–c) were obtained by averaging the data obtained from 60-times repetitive measurements. Error bars in (a) and (b) are smaller than the marker sizes and those in (c) represent one standard error of the mean in the repetitive measurements.
SHDG measurement in transition flow regime
We also carried out measurements on the SHDG in a transition flow regime by using the channel with ϕ = 200 μm and L = 100 mm. In the measurement, Re was modulated between 200 and 2210 only by changing P. As shown in Fig. 4a, the relation between P and v changes from the linear relation to the square-root one with increasing P, indicating that the Hg flow changed from the laminar flow regime to the turbulent one in the measurement. The intermediate region of P = 150~300 kPa is the transition region from the laminar flow to the turbulent flow, in which the flow seems to be unstable. In Fig. 4b, we show the P dependence of Ve. In low P region, Ve is in good agreement with the black solid line, which is the theoretical calculation of the laminar-flow SHDG using θSHEλ2ξ = 1.9 × 10−25 J s m−1 estimated from the fit to the data in Fig. 3c. In Fig. 4c, we show the v∗r0 vs. \({{r}_{0}}^{3}{V}_{{\rm{e}}}{L}^{-1}\) plot so as to discuss the turbulent flow, where v∗ is the friction-velocity21. \({{r}_{0}}^{3}{V}_{{\rm{e}}}{L}^{-1}\) in the high v∗r0 region, namely the high velocity region, is in good agreement with the black solid curve, which is the theoretical calculation of the turbulent-flow SHDG using12 θSHEλ2ξ = 5.9 × 10−25 J s m−1. The above results indicate that the low and high Re region are consistent with the SHDG theory of the laminar and turbulent flow, respectively, and that the SHDG voltage continuously changes from the laminar behavior to the turbulent one with changing Re across the transition flow regime.
a P dependence of v for the channel of ϕ = 200 μm. v is estimated by averaging the data obtained from repetitive measurements. The experimental results are well reproduced by a relation for laminar flow states in low P region (v ∝ P) and a relation for turbulent flow states in high P region (\(v\propto \sqrt{P}\)). b P dependence of Ve for the channel used in (a). Ve is estimated by averaging the data obtained from repetitive measurements. The black solid line represents the theoretical calculation of the laminar-flow SHDG shown in Fig. 3c (red solid line). c v∗r0 vs. \({{r}_{0}}^{3}{V}_{{\rm{e}}}{L}^{-1}\) plot. v∗ and r0 represent the friction-velocity and the inner radius, respectively. The black solid curve represents the theoretical calculation of the turbulent-flow SHDG shown in12. d Dependence of the energy conversion efficiency η on the Reynolds number Re for various values of ϕ. η estimated from the experimental results of the present study, indicated by filled circles in the laminar and the transition region, are shown together with that in the turbulent region12 (open circles). Inset shows Re dependence of η for the ϕ-200-μm channel with a linear scale. e Re vs. \({{r}_{0}}^{3}\eta\) plot for various values of ϕ. The black solid lines represent the relations of \({{r}_{0}}^{3}\eta \propto {\rm{Re}}^{-1}\) and \({{r}_{0}}^{3}\eta \propto {\rm{Re}}\). Inset shows Re vs. \({{r}_{0}}^{3}\eta\) plot for the ϕ-200-μm and the ϕ-400-μm channels with a linear scale.
Estimation of energy conversion efficiency
Finally, we estimate the energy conversion efficiency of the present SHDG. In the estimation, the energy injection per unit time Win is assumed to be same as the kinematic energy gain per unit time calculated by using v: \({W}_{{\rm{i}}\mathrm{n}}=\rho \pi {{r}_{0}}^{2}{v}^{3}/2\), where ρ is the mass density. Energy generation per unit time via SHDG, Wout, is estimated as the electric power: \({W}_{{\rm{out}}}=\pi {{r}_{0}}^{2}{\sigma }_{0}{{V}_{\rm{e}}}^{2}/L\), and thus the energy efficiency η is estimated to be Wout/Win. Figure 4d shows the Re dependence of η, indicating significant improvement of the efficiency in the laminar state; the laminar-flow SHDG is much more efficient than the turbulent-flow SHDG. The maximum magnitude of η in the laminar flow in our set-up is 105 times greater than that in the turbulent flow: giant SHDG. A flow with smaller Reynolds number, that is, a slower flow in a smaller channel, should be more efficient in the SHDG energy conversion. If we prepare a sample with L ~ 1 mm, r0 ~ 1 μm and Re ~ 10−6, which can be realized by using microfluidic devices, we can realize efficiency about 10%. It is to be noted that the data in Fig. 4d seems to jump by changing Re. This is because η depends on not only Re but also r0 as follows: \(\eta \propto L\,{{r}_{0}}^{-3}\mathrm{R{e}}^{-1}\) in the laminar flow regime and \(\eta \sim L\,{{r}_{0}}^{-3}\mathrm{Re}\) in the turbulent one.
Examination of continuity of SHDG phenomenon
The inset in Fig. 4d shows Re dependence of η for the ϕ-200-μm channel with a linear scale. In the low Re region (Re < 1000), η decreases with increasing Re. This behavior is consistent with the results of the laminar flow. In the high Re region (Re > 2000), however, η increases with increasing Re. This behavior is also consistent with the results of the turbulent flow. In the intermediate region (1000 < Re < 2000), η is almost independent of Re. The result indicates that η is continuous across the region between the laminar and turbulent flow. To further examine the continuity of the SHDG phenomenon, we plot Re dependences of \({{r}_{0}}^{3}\eta\) for various values of ϕ in Fig. 4e. In the Re – \({{r}_{0}}^{3}\eta\) scale, we could deal with the SHDG phenomenon without considering the direct dependence on r0 because of the theoretical prediction of η described above. The result shows that \({{r}_{0}}^{3}\eta\) is proportional to Re−1 in the laminar flow regime, while it is proportional to Re in the turbulent one, being consistent with the SHDG theory. In the inset in Fig. 4e, we replot Re dependences of \({{r}_{0}}^{3}\eta\) for the ϕ-200-μm and ϕ-400-μm channels with a linear scale. The result also indicates the continuity of the SHDG phenomenon in the laminar-to-turbulent crossover regime because there is no measurable data jump and the values of \({{r}_{0}}^{3}\eta\) seem to change smoothly from the laminar behavior to the turbulent one. Therefore, all the results suggest that the SHDG phenomenon changes continuously from the laminar to the turbulent one across the laminar-to-turbulent crossover regime.
Discussion
Our finding highlights the energy conversion efficiency of the SHDG, revealing that the SHDG in the laminar flow is much more efficient than that in the turbulent flow. From application points of view, the SHDG has also unique advantages: the voltage generation dependent on the flow rate as shown in Eq. (2) and the undisturbance to the flow because of the absence of accessories in the channel to measure the flow rate. These advantages may enable us to make a miniaturized flow sensor for a liquid metal, which could be used, for example, as an active cooling system in a fast-breeder reactor, a semiconductor device and so on.
Methods
Experimental set-up
In the present study, we measured the electric voltage difference Ve between the ends of the cylindrical quartz-glass channel (Nakahara Opto-Electronics Laboratories, Inc.) filled with the liquid-metal mercury (Hg, 99.5%; Wako Pure Chemical Industries, Ltd.) by using a nanovoltmeter (2182A; Keithley Instruments, Inc.) while measuring the amount of Hg discharged from the channel simultaneously to estimate the mean flow velocity v by using an electronic balance (HR-250AZ; A&D, Co., Ltd.). To generate a flow of Hg, we applied the pulsed pressure P to the liquid reservoir connected to the channel inlet by using a pressure controller (PACE5000; GE Sensing & Inspection Technologies, Co., Ltd.). All the measurements were performed at room temperature.
Data availability
All relevant data are available from the corresponding author upon reasonable request.
References
Maekawa, S. (ed.) Concepts in Spin Electronics (Oxford Univ. Press, 2006).
Maekawa, S., Valenzuela, S. O., Saitoh, E. & Kimura, T. (eds) Spin Current (Oxford Univ. Press, 2012).
Uchida, K. et al. Observation of the spin Seebeck effect. Nature 455, 778–781 (2008).
Slachter, A., Bakker, F. L., Adam, J.-P. & van Wees, B. J. Thermally driven spin injection from a ferromagnet into a non-magnetic metal. Nat. Phys. 6, 879–882 (2010).
Bauer, G. E. W., Saitoh, E. & van Wees, B. J. Spin caloritronics. Nat. Mater. 11, 391–399 (2012).
Flipse, J., Bakker, F. L., Slachter, A., Dejene, F. K. & van Wees, B. J. Direct observation of the spin-dependent Peltier effect. Nat. Nanotechnol. 7, 166–168 (2012).
Kobayashi, D. et al. Spin current generation using a surface acoustic wave generated via spin-rotation coupling. Phys. Rev. Lett. 119, 077202 (2017).
Matsuo, M., Saitoh, E. & Maekawa, S. Spin-Mechatronics. J. Phys. Soc. Jpn. 86, 011011 (2016).
Zolfagharkhani, G. et al. Nanomechanical detection of itinerant electron spin flip. Nat. Nanotechnol. 3, 720–723 (2008).
Matsuo, M., Ieda, J., Harii, K., Saitoh, E. & Maekawa, S. Mechanical generation of spin current by spin-rotation coupling. Phys. Rev. B 87, 180402 (2013).
Ieda, J., Matsuo, M. & Maekawa, S. Theory of mechanical spin current generation via spin-rotation coupling. Solid State Commun. 198, 52–56 (2014).
Takahashi, R. et al. Spin hydrodynamic generation. Nat. Phys. 12, 52–56 (2016).
Matsuo, M., Ohnuma, Y. & Maekawa, S. Theory of spin hydrodynamic generation. Phys. Rev. B 96, 020401 (2017).
Otani, Y., Shiraishi, M., Oiwa, A., Saitoh, E. & Murakami, S. Spin conversion on the nanoscale. Nat. Phys. 13, 829–832 (2017).
Žutić, I. & Matos-Abiague, A. Fluid spintronics: cause a stir. Nat. Phys. 12, 24–25 (2016).
Ciudad, D. Spintronics: turbulent power. Nat. Mater. 14, 1188 (2015).
Stajic, J. Make way for liquid spintronics. Science 350, 924–925 (2015).
Ogata, Y. et al. Gyroscopic g factor of rare earth metals. Appl. Phys. Lett. 110, 072409 (2017).
The STAR collaboration. Global Λ hyperon polarization in nuclear collisions. Nature 548, 62–65 (2017).
Gad-el-Hak, M. (ed.) The MEMS Handbook Ch. 6 (CRC press, 2001).
Landau, L. D. & Lifshitz, E. M. Fluid Mechanics Second Edition Ch. 1, 2 & 4 (Butterworth-Heinemann, 1987).
Shaw, P. E. Experiments on tribo-electricity. I. The tribo-electric series. P. Roy. Soc. Lond. A. Mat. 94, 16–33 (1917).
Diaz, A. F. & Felix-Navarro, R. M. A semi-quantitative tribo-electric series for polymeric materials: the influence of chemical structure and properties. J. Electrostat. 62, 277–290 (2004).
Yarnold, G. D. The electrification of mercury indexes in their passage through tubes. Proc. Phys. Soc. 52, 196–201 (1940).
Acknowledgements
The authors thank Y. Tsutsumi for valuable discussions. This work was supported by JST-ERATO Spin Quantum Rectification, Japan, a Grant-in-Aid for Scientific Research on Innovative Areas Nano Spin Conversion Science (JP26103005) from MEXT KAKENHI, Japan, a Grant-in-Aid for Research Activity start-up (JP16H07437) from JSPS KAKENHI, Japan, a Grant-in-Aid for Scientific Research (C) (JP15K05153) from MEXT KAKENHI, Japan, a Grant-in-Aid for Scientific Research (B) (JP16H04023, JP17H02927 and JP20H01863) from MEXT KAKENHI, Japan, a Grant-in-Aid for Scientific Research (S) (JP19H05600) from JSPS KAKENHI, Japan, and Priority Program of Chinese Academy of Sciences (XDB28000000), China.
Author information
Authors and Affiliations
Contributions
R.T., H.C., K.H., and E.S. designed the experiments; R.T. collected and analyzed the data; R.T., M.M., K.H., Y.O., and S.M. developed the theoretical explanation; R.T. wrote the manuscript. All authors discussed the results and commented on the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer review information Nature Communications thanks Sergio Caprara, Evangelos Papaioannou and the other, anonymous, reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Takahashi, R., Chudo, H., Matsuo, M. et al. Giant spin hydrodynamic generation in laminar flow. Nat Commun 11, 3009 (2020). https://doi.org/10.1038/s41467-020-16753-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-020-16753-0
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.