Abstract
Negative capacitance (NC) effects in ferroelectric/paraelectric (FE/PE) stacks have been recently discussed intensively in terms of the steep subthreshold swing (SS) in field-effect transistors (FETs). It is, however, still disputable to stabilize quasi-static-NC effects. In this work, stepwise internal potential jumps in a metal/FE/metal/PE/metal system observed near the coercive voltage of the FE layer are reported through carefully designed DC measurements. The relationship of the internal potential jumps with the steep SS in FETs is also experimentally confirmed by connecting a FE capacitor to a simple metal-oxide-semiconductor FET. On the basis of the experimental results, the observed internal potential jumps are analytically modelled from the viewpoint of bound charge emission associated with each domain flip in a multiple-domain FE layer in a FE/PE stack. This view is different from the original NC concept and should be employed for characterizing FE/PE gate stack FETs.
Similar content being viewed by others
Introduction
Negative capacitance (NC) effects in ferroelectric (FE) films have attracted intensive attention recently in terms of both polarization kinetics modeling and low-power complementary metal-oxide-semiconductor (CMOS) applications. The original idea of NC was proposed from the fact that the Landau-Devonshire theory would possess an intrinsic NC state in a FE capacitor (CAP) with a single domain, namely an S-like polarization-voltage behavior. Although this effect is not observable in a single FE-CAP, it is expected to be stabilized by connecting a linear paraelectric (PE) CAP in series. Furthermore, since it may achieve an internal voltage amplification in gate stacks of field-effect transistors (FETs) by using the FE/PE stacks, it is very attractive that the Boltzmann tyranny (60 mV dec−1 at room temperature) in subthreshold slope (SS) may be surmounted1. Such a device with no hysteresis is often called a NC-FET. In a decade, many groups have focused on studying NC effects in FE/PE stacks and FE/PE gate stack FETs2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24. Concerning NC effects in FE/PE stacks, three kinds of demonstrations have been provided experimentally so far: (i) total capacitance enhancement in the case of no internal metal between FE and PE layers2,3,4, (ii) transient NC effects in AC mode operation5,6,7, and (iii) locally stabilized NC state8. Several models of quasi-static NC associated with domain wall motion in a multiple-domain system have been also proposed9,10,11,12,13. Meanwhile, steep SS values have been demonstrated by incorporating FE/PE gate stacks into FETs with various FE materials14,15,16, various channel materials15,17,18,19 and various FET structures14,20,21,22,23,24.
However, physical understanding of NC effects is still under intensive debate25,26,27,28,29,30,31,32,33,34,35,36. Experimentally observed NC effects are different from each other, and also from the concepts initially proposed. Alternative explanations for the capacitance enhancement and transient NC effects in FE/PE stacks have been also proposed25,26,27,28,29,30,31. For example, a feasibility of capacitance enhancement is explainable from a strong coupling between FE and PE layers25,26,27, while the transient NC is understandable from the viewpoints of overshoot in voltage supply or slower speed of charge compensation relative to polarization switching in FE-CAP28,29,30,31. In fact, it has been argued that NC region of FE material is intrinsically unstable or even impossible32,33. In addition, the SS improvements observed in FETs mostly suffer from critical problems that a large hysteresis is detected, a high voltage is needed and an operation frequency is limited in actual experiments34,35,36.
To sum up, the experimental evidences provided so far are insufficient to conclude the concept of quasi-static NC, and reliable modeling of SS improvement in a FET with FE/PE gate stack is still missing. These should be verified urgently, because they are critical for further advancing the material science as well as electron device performance of FE/PE stacks to elucidate whether the quasi-static NC can be really stabilized or not, and whether the steep SS characteristics so far demonstrated are really promising for low-power CMOS applications or not. A direct way to examine the actual FE effect in FE/PE stack is to investigate the voltage at the internal node, Vint, between FE and PE layers in DC mode, which makes possible of the direct correlation of Vint with SS in FET. In fact, a couple of works on internal potential measurement have been reported, but they have only qualitatively discussed about this issue, resulting that a consistent model could not been provided16,37. We have suspected it might be due to experimental difficulties of measuring the internal potential in FE/PE stack. Therefore, in this work, accurate DC measurements are particularly paid careful attention. The stepwise Vint jumps at the coercive voltage, ±VC, of FE layer in FE/PE stack are demonstrated, and a relationship between Vint jumps and the steep SS in FET with FE/PE gate stack is presented. They are quantitatively understood from the viewpoints of successive polarized domain flipping and depolarization feedbacks from the PE-CAP. The results provide a clear physical insight to understanding the small SS values in FETs with FE/PE gate stacks reported so far.
Results
DC measurement of internal potential in FE/PE stack
To accurately estimate Vint in FE/PE stack in DC mode, a PE/PE stack was firstly inspected quantitatively. In an ideal case, total charges at the internal metal, which is electrically floating, have to be conserved as long as no leakage current through both CAPs is assured (Fig. 1a). However, since the DC output impedance at the floating node is infinite in the ideal case, it is substantially impossible to estimate Vint experimentally. In actual cases, a finite resistance of capacitors enables to measure Vint in DC-mode, while a time constant should be considered for a quantitative analysis. More importantly, a small but a finite amount of charge-flow from the internal metal to a measurement system should also be paid attention to, because the measured voltage in itself is significantly affected by the input impedance in the measurement system. Thus, the actual equivalent circuit concerned in this work is shown in Fig. 1b. Based on the formulation shown in Supplementary Note 138 and the measured resistance of PE CAPs (~1012 Ω), a voltage measurement system with the input impedance higher than ~1014 Ω was needed for accurate DC-mode measurements. We used a high input impedance voltmeter equipped with a high precision current preamplifier, which was able to adjust a voltage to suppress a current flow down to zero (sub-fA level). By doing so, the effective input impedance was enhanced up to 1016 Ω. Figure 1c compares Vint in PE/PE stacks measured in the present system and in conventional voltmeter with an input impedance of ~1010 Ω. When the present system was employed, the accurate measurement of Vint was successfully assured for capacitors with down to 1 pF. Namely, it is critically important for characterizing the Vint quantitatively to take the input impedance of the measurement system into account.
In actual measurements of Vint in FE/PE stacks, commercially available PZT films with Pt electrodes were used as the FE-CAPs. The typical charge–voltage (Q-VF), capacitance–voltage (CF-VF) and leakage (I-VF) characteristics are shown in Supplementary Fig. 1. The capacitance at the center of CF-VF characteristics was ~0.25 nF and the leakage current density at 1 V was below ~10−8 A cm−2, which is comparable to the level reported for the state of the art PZT39,40 and corresponds to 5 × 1010 Ω. The equivalent circuit of the Vint measurement in FE/PE system shown in Fig. 2a was assumed, in which impedances in both PE-CAP and measurement system were much higher than that in PZT. In prior to measurements, the FE-CPA was polarized by a negative voltage, and the internal terminal of FE/PE stack was grounded to remove the unknown charges stored. More details in the measurements are described in the method section. Figure 2b and c show Vint and δVint/δV in sweepings of the total voltage, V, in the case with PE capacitance (CP) of 0.5 nF. A big Vint jump is seen in both forward and backward V sweepings, and each of them corresponds to the differential gain of Vint (δVint/δV > 1). It is noted that the big Vint jump is followed by successively oscillating small ones as shown in enlarged part of Fig. 2b. VF calculated by subtracting measured Vint from V is shown as a function of V in Fig. 2d. Note that the VF drops along with the Vint jumps occur very near ±VC in FE-CAP. It directly indicates that the Vint gain is associated with the polarization flip in a FE layer. This fact is critically important from the viewpoint that it is beyond the qualitative observation in the similar measurements reported recently16,37. It is worthy of mentioning that the measured voltage was time dependent and it gradually changed due to the finite resistance in FE and PE layers as mentioned above. Therefore, the absolute value of Vint is not as expected in CP-CF circuit. Both V and Vint are, however, accurately measurable and VF obtained by V-Vint should also be accurate quantitatively, as long as the input impedance of voltmeter is effectively higher than the output impedance in the PE-CAP and FE-CAP and the measurement time is substantially smaller than the time constant of the FE/PE system. This is further confirmed by the results in Supplementary Fig. 2, that the experimental observations are well reproduced by repeating the measurement for three times and the VF positions corresponding to Vint jumps remain to be near ±VC even by changing CP from 15 nF down to 0.1 nF. In addition, a possible origin of the Vint variation in FE/PE system might be the time constant variation originated from the bias dependence of resistance and/or capacitance of FE-CAP. But, such a concern is irrelevant to the present experimental observations, because the results are not affected at all even in the FE/PE stacks with different time constants (with different CP values).
Correlating internal potential gain with steep SS in FET
A relationship of the internal potential gain with the SS improvement in FET operation is next investigated. A FE-CAP was connected through a cable to a poly-Si gate/SiO2 metal-oxide-semiconductor FET (MOSFET) with a channel width, length, and oxide thickness of 200 μm, 500 μm, and 5 nm, respectively. Accumulated MOS capacitance was ~0.7 nF and gate leakage was ~10−9 A cm−2 at 1 V. The equivalent circuit is shown in Fig. 3a. The source-drain current (IDS) and Vint of the FE-CAP/MOSFET stack were measured separately in gate bias (VGS) sweeping under drain voltage (VDS) of 0.1 V. It is mandatory to eliminate unknown charge effects at the internal node in FE/MOSFET prior to each measurement, because floating charges are very likely to affect the charge dynamics in the domain reversal. This is critical for considering the hysteresis in IDS-VGS characteristics of FE/MOSFET system. Figure 3b shows IDS-VGS curves w/ and w/o connecting the FE-CAP. The SS in the case w/ FE-CAP clearly looks sharper than that in w/o case in a given VGS region. Figure 3c plots VGS dependence of SS. In the case w/ FE CAP, SS is improved down to sub-60 mV dec−1 both in forward and backward sweepings. δVint/δVGS as a function of VGS is shown in Fig. 3d. Note that the improvement factor of SS (a ratio of SS w/o to w/ FE-CAP) is roughly the same as δVint/δVGS in Fig. 2d. These results indicate that the steep SS value below the Boltzmann limit is definitely associated with Vint gain in FE/MOSFET system.
Electrostatic understanding of internal potential gains
Next, a possible kinetic origin of stepwise Vint jumps is discussed. The charge dynamics associated with the domain flipping in FE/PE stack is a main focus. We suppose the capacitance coupling circuit in FE/PE stack for characterizing internal charge kinetics in the following.
It is here noted that two kinds of charges are involved in FE-CAP: bound charges (Qbound) and free charges (Qfree), as shown in Fig. 4a, where the positive polarization, P, is defined as the arrow from left to right. If FE-CAP is pre-polarized by a negative voltage as that in the experiments, Qbound = −P initially. According to electrostatics, the relevant system should satisfy the following equations before the polarization switching:
in which Q denotes total charges accumulated on each CAP. Assuming CF is constant, Vint and VF are expressed by
Since the bound charges are fixed in the case without polarization flipping, the FE/PE stack is similar to a PE/PE one. Thus,
On the other hand, when the polarization flipping occurs at VF = ~VC (taking the forward sweeping as an example), the polarization, P, should change the direction in Eqs. (3), (4) and (5). Namely, a bunch of charges are transferred from FE-CAP to PE-one. If we assume FE layer is with a single domain,
This indicates that δVint > δV can become to be >1 in case with a relatively small CP. Namely, Vint jump along with VF drop should occur in this case.
In actual FE films, multiple domains are involved and not all domains flip simultaneously. Here, it is reasonably assumed that each domain flips independently and that it has each VC with a tight distribution in FE film. When a certain domain flips with a relatively small CP, VF should be reduced due to a finite amount of charge transfer from FE-CAP to PE-one. It means that remaining domains cannot flip before further increase in VF to VC. When VF is increased to VC again, another domain flips, followed by the VF drop again. Thus, the initial Vint jump and VF drop followed by oscillating Vint-V and VF-V characteristics near VC are clearly explained. The stepwise Vint jumps are analytically described as
in which Pi (i = 1, 2, 3…) is the polarization of each domain in a FE film. Since the VF drop means the depolarization field formation in FE-CAP, each Vint jump can be regarded as a depolarization feedback from PE-CAP associated with each domain flip. Namely, successive multiple-domain flips accompanying the depolarization feedbacks from PE-CAP result in zigzag Q-VF characteristics. These views are schematically shown in Fig. 4b in detail. Note that the resulted zigzag Q-VF characteristics is totally different from the conventional Q-VF curve in a single FE-CAP or from the S-curve expected from the original NC theory1. It is also significantly different from the characteristics expected from the recent models with the multiple-domain system, in which a continuous change of polarization with the help of domain wall motion is assumed9,10,11,12,13.
Hysteresis of the Vint gain is critical for achieving steep SS FETs in advanced CMOS. According to our modeling, nearly hysteresis-free Vint gain is made possible in principle by inserting an appropriate CP in the case of the single domain FE in FE/PE stack. The requirement for this condition is the same as that for stabilizing NC effect originally proposed. This is also partly consistent with a recent report in which nearly single domain PZT film together with strict capacitance matching was employed and a nearly hysteresis-free steep SS was demonstrated23,24. In the case of FE layer containing multiple domains, the hysteresis-free Vint gain is difficult to achieve perfectly. Here, let us focus on the biggest Vint gain. Since the V value and amplitude of this Vint jump are controlled by CP and P1, respectively, it becomes possible that the biggest Vint jump in the forward V sweeping may overlap with that in the backward one by adjusting P1 under an optimum CP, (Fig. 4c). Resultantly, the subthreshold hysteresis in FETs should be substantially reduced in the overlapped range. As a matter of fact, the bias dependence of semiconductor capacitance makes hysteresis-free FET more difficult. Thus, hysteresis is seen in most of the steep-SS FETs reported up to now16,22,23. More detailed discussion of the hysteresis is shown in Supplementary Fig. 3 and Supplementary Note 2.
In addition, it should be mentioned that the domain–domain interaction is needed to take into consideration and the internal field inside the film may be reduced in the first domain switching in the real multiple-domain system. These effects should affect the voltages for successive domain flipping. In fact, our results in Fig. 1d show that the successive domain flips, following the biggest one, occur at VF values slightly smaller than VC.
Difference between present and original views on NC effect
The intrinsic difference between our view and the original proposal on NC effects in FE-based FETs is next discussed. To be fair, only the case of single domain is considered. The Vint gain is actually obtained in both cases. In the present view, it is associated with the domain flip, on the assumption that an intermediate state between two polarized states in the domain is not stable quasi-statically (Fig. 5a). This requires that the gate voltage should be high enough to enable VF > VC. While in the original NC proposal, the intermediate state with a small polarization value can be stabilized with a small CP, and the Vint gain is obtainable even at VF = 0 (Fig. 5b). It remains still unclarified whether it is possible to access to the intermediate polarized state quasi-statically or not. It is, however, strongly inferred that the continuous change of polarization in a domain is very improbable from the present experimental results. This is also consistent with the fact that no observation of the SS improvement under a small gate voltage swing has been reported so far.
Finally, it is worthy of mentioning that the polarization switching kinetics depends on a specific model such as Kolmogorov-Avrami-Ishibashi or nucleation-limited switching models31,41, while specific switching kinetics does not necessarily lead to the total frustration of the Vint enhancement effect12. Namely, when the depolarization field is formed due to the bound charge movement, the Vint gain can be obtained in any switching kinetics cases. Meanwhile, the gain value, shape and time dependence of Vint, might be affected. But such consideration is beyond the scope of this paper in which the DC-mode polarization switching rather than high-speed switching is focused. When the polarization switching speed is concerned in device applications, the specific domain switching kinetics should be taken into account for the NC effect analysis. In addition, in the case of multiple-domain system, there will be a difference between the cases w/ and w/o internal electrode. In the latter case, the charge flow at FE/PE interface, the local effect of domain switching and the coupling effects between FE and PE layer should be taken into consideration11,25,26,27. It is very interesting to further study these issues.
Discussion
This work demonstrates stepwise internal potential jumps associated with successive domain flips in multiple-domain FE/PE stack, and a direct relationship of this effect with steep SS in a SiO2 MOSFET connected with a FE capacitor. Each domain flip provides an internal potential gain in FE/PE stack with a suitable PE capacitance as originally proposed NC effect, while a stable intermediate state between two polarization states is very unlikely. Thus, the power supply voltage surmounting the coercive voltage on FE layer is required, which is not advantageous for low-power device applications. The nearly hysteresis-free steep SS FET may be possible with a single-domain FE layer by tuning PE capacitance, while that with a multiple-domain FE layer is very challenging. It is likely that most of small SS values so far reported in literatures are explainable by the present model.
Methods
Measurement circuits of FE/PE and FE/MOSFET systems
PZT-CAPs with Pt electrodes available from Radiant Technologies Inc. and conventional PE-CAPs were used. FE and PE CAPs were connected in series by a coaxial cable. A DC-voltage measurement system (Keithley 6430) equipped with a remote sub-fA pre-amplifier was connected to the internal metal node between FE and PE CAPs to measure the internal potential. This enabled us to effectively increase the input impedance of the measurement system up to 1016 Ω. For FE/MOSFET system, poly-Si gate/SiO2/Si MOSFET was connected to PZT-CAP in series. The FE/MOSFET system was connected to a semiconductor parameter analyzer (Keysight B1500) for IDS-VGS characterization, while the high impedance system was connected to the internal metal between FE and MOSFET for internal potential measurement. Both experiments were carried out separately under the same VDS.
Electrical measurement
Before measurement, each terminal in FE/PE and FE/MOSFET circuits was grounded to remove unknown charges left inside. Then the internal potential, Vint, was measured by sweeping the total voltage, V, with a step of 50 mV. In each step, a waiting-time of 0.1 s was set for stabilizing the voltage and a total time of 0.5 s was taken for each point measurement. For the FE/MOSFET system, in addition to Vint measurement, FET characteristics were measured with the source grounded under VDS = 0.1 V. The sweeping step of VGS was 20 mV and the waiting-time for each step measurement was 0.1 s.
Data availability
The experimental data in the present study are available from the corresponding author upon reasonable request.
References
Salahuddin, S. & Datta, S. Use of negative capacitance to provide voltage amplification for low power nanoscale devices. Nano Lett. 8, 405–410 (2008).
Khan, A. I. et al. Experimental evidence of ferroelectric negative capacitance in nanoscale heterostructures. Appl. Phys. Lett. 99, 113501 (2011).
Appleby, D. J. et al. Experimental observation of negative capacitance in ferroelectrics at room temperature. Nano Lett. 14, 3864–3868 (2014).
Gao, W. et al. Room-temperature negative capacitance in a ferroelectric-dielectric superlattice heterostructure. Nano Lett. 14, 5814–5819 (2014).
Khan, A. I. et al. Negative capacitance in a ferroelectric capacitor. Nat. Mater. 14, 182–186 (2014).
Hoffmann, M. et al. Direct observation of negative capacitance in polycrystalline ferroelectric HfO2. Adv. Funct. Mater. 26, 8643–8649 (2016).
Hoffmann, M. et al. Unveiling the double-well energy landscape in a ferroelectric layer. Nature 565, 464–467 (2019).
Yadav, A. K. et al. Spatially resolved steady-state negative capacitance. Nature 565, 468–471 (2019).
Luk’yanchuk, I., Sené, A. & Vinokur, V. M. Electrodynamics of ferroelectric films with negative capacitance. Phys. Rev. B 98, 024107 (2018).
Luk’yanchuk, I., Tikhonov, Y., Sené, A., Razumnaya, A. & Vinokur, V. M. Harnessing ferroelectric domains for negative capacitance. Commun. Phys. 2, 22 (2019).
Hoffmann, M., Pešić, M., Slesazeck, Stefan, Schroeder, Uwe & Mikolajick, T. On the stabilization of ferroelectric negative capacitance in nanoscale devices. Nanoscale 10, 10891–10899 (2018).
Park, H. W., Roh, J., Lee, Y. B. & Hwang, C. S. Modeling of negative capacitance in ferroelectric thin films. Adv. Mater. 31, 1805266 (2019).
Íñiguez, J., Zubko, P., Luk’yanchuk, I. & Cano, A. Ferroelectric negative capacitance. Nat. Rev. Mater. 4, 243–256 (2019).
Rusu, A., Salvatore, G. A., Jimenez, D. & Ionescu, A. M. Metal-ferroelectric-metal-oxide-semiconductor filed effect transistor with sub-60 mV/decade subthreshold swing. In International Electron Devices Meeting 395–398 (IEEE, 2010).
Li, K. et al. Sub-60mV-swing negative-capacitance FinFET without hysteresis. In International Electron Devices Meeting 620–623 (IEEE, 2015).
Saeidi, A., Jazaeri, F., Stolichnov, I., Enz, C. C. & Ionescu, A. M. Negative capacitance as universal digital and analog performance booster for complementary MOS transistors. Sci. Rep. 9, 9105 (2019).
Yu, Z. et al. Negative capacitance 2D MoS2 transistors with sub-60mV/dec subthreshold swing over 6 orders, 250 μA/um current density, and nearly-hysteresis-free. In International Electron Devices Meeting 577–580 (IEEE, 2017).
Zhou, J. et al. Ferroelectric HfZrOx Ge and GeSn PMOSFETs with Sub-60 mV/decade subthreshold swing, negligible hysteresis, and improved I DS. In International Electron Devices Meeting 310–313 (IEEE, 2016).
Si, M. et al. Steep-slope hysteresis-free negative capacitance MoS2 transistors. Nat. Nanotechnol. 13, 24–28 (2017).
Krivokapic, Z. et al. 14 nm ferroelectric FinFET technology with steep subthreshold slope for ultra-low power applications. In International Electron Devices Meeting 357–360 (IEEE, 2017).
Su, C. J. et al. Ge Nanowire FETs with HfZrOx ferroelectric gate stack exhibiting SS of sub-60 mV/dec and biasing effects on ferroelectric reliability. In International Electron Devices Meeting 369–372 (IEEE, 2017).
Saeidi, A. et al. Negative capacitance as performance booster for tunnel FETs and MOSFETs: an experimental study. IEEE Electron Dev. Lett. 38, 1485–1488 (2017).
Saeidi, A. et al. Near hysteresis-free negative capacitance InGaAs tunnel FETs with enhanced digital and analog figures of merit below VDD=400mV. In International Electron Devices Meeting 304–307 (IEEE, 2018).
Verhulst, A. et al. Experimental details of a steep-slope ferroelectric InGaAs tunnel-FET with high-quality PZT and modeling insights in the transient polarization. IEEE Trans. Electron Devices 63, 377–382 (2020).
Tsang, C. H., Chew, K., Ishibashi, Y. & Shi, F. G. Structure of interfaces in layered ferroelectrics of first and/or second order transition. J. Phys. Soc. Jpn. 73, 3158–3165 (2004).
Dawber, M. et al. Unusual behavior of the ferroelectric polarization in PbTiO3/SrTiO3 superlattices. Phys. Rev. Lett. 95, 177601 (2005).
Salev, P., Mahayni, A. & Grigoriev, A. Polarization coupling transition in BaTiO3/PbZ0.2Ti0.8O3 ferroelectric bilayers. Phys. Rev. B 93, 041423 (2016).
Song, S. J. et al. Alternative interpretations for decreasing voltage with increasing charge in ferroelectric capacitors. Sci. Rep. 6, 20825 (2016).
Saha, A. K., Datta, S. & Gupta, S. K. “Negative capacitance” in resistor-ferroelectric and ferroelectric-dielectric networks: apparent or intrinsic? J. Appl. Phys. 123, 105102 (2018).
Kittl, J. A. et al. On the validity and applicability of models of negative capacitance and implications for MOS applications. Appl. Phys. Lett. 113, 042904 (2018).
Kim, Y. J. et al. Voltage drop in a ferroelectric single layer capacitor by retarded domain nucleation. Nano Lett. 17, 7796–7802 (2017).
Liu, Z., Bhuiyan, M. A. & Ma, T. P. A critical examination of ‘quasi-static negative capacitance’ (QSNC) theory. In International Electron Devices Meeting 711–714 (IEEE, 2018).
Houdt, J. V. & Roussel, P. Physical model for the steep subthreshold slope in ferroelectric FETs. IEEE Electron Dev. Lett. 39, 877–880 (2018).
Kobayashi, M., Ueyama, N., Jang, K. & Hiramoto, T. Experimental study on polarization-limited operation speed of negative capacitance FET with ferroelectric HfO2. In International Electron Devices Meeting 314–317 (IEEE, 2016).
Obradovic, B., Rakshit, T., Hatcher, R., Kittl, J. & Rodder, M. S. Ferroelectric switching delay as cause of negative capacitance and the implications to NCFETs. In Symposium on VLSI Technical 51–52 (IEEE, 2018).
Wang, H. et al. New insights into the physical origin of negative capacitance and hysteresis in NCFETs. In International Electron Devices Meeting 707–710 (IEEE, 2018).
Jo, J. et al. Negative capacitance in organic/ferroelectric capacitor to implement steep switching MOS devices. Nano Lett. 15, 4553–4556 (2015).
Khan, A. I., Radhakrishna, U., Chatterjee, K., Salahuddin, S. & Antoniadis, D. A. Negative capacitance behavior in a leaky ferroelectric. IEEE Trans. Electron Devices 63, 4416–4422 (2016).
Natarajan, V., Varadarajan, E., Rath, M. & Parui, J. Studies on piezo coefficients of PLD and sol-gel grown PZT thin film for devices. Integr. Ferroelectrics 193, 100–105 (2018).
Podgorny, Y., Vorotilov, K. & Sigov, A. Estimation of steady-state leakage current in polycrystalline PZT thin films. AIP Adv. 6, 095025 (2016).
Scott, J. F. A review of ferroelectric switching. Ferroelectrics 503, 117–132 (2016).
Acknowledgements
This work was supported by JST-CREST (JPMJCR14F2) in Japan and partly by National Natural Science Foundation of China (61904103, 91964110) and Shanghai Science and Technology Innovation Action Plan (19ZR1475300, 19JC1416700) in China. We would thank T. Nishimura and T. Yajima at The University of Tokyo for discussion and suggestions.
Author information
Authors and Affiliations
Contributions
A.T. conceived the idea of internal potential measurement in FE/PE and FE/MOSFET systems and supervised the experiments. X.L. performed circuit setup, the electrical measurement and the data analysis. X.L. and A.T. proposed the physical model and summarized the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer review information Nature Communications thanks Cheol Seong Hwang, Adrian Ionescu, and the other, anonymous, reviewer(s) for their contribution to the peer review of this work. Peer review reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Li, X., Toriumi, A. Stepwise internal potential jumps caused by multiple-domain polarization flips in metal/ferroelectric/metal/paraelectric/metal stack. Nat Commun 11, 1895 (2020). https://doi.org/10.1038/s41467-020-15753-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-020-15753-4
This article is cited by
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.