The communication outposts of the emerging Internet of Things are embodied by ordinary items, which desirably include all-printed flexible sensors, actuators, displays and akin organic electronic interface devices in combination with silicon-based digital signal processing and communication technologies. However, hybrid integration of smart electronic labels is partly hampered due to a lack of technology that (de)multiplex signals between silicon chips and printed electronic devices. Here, we report all-printed 4-to-7 decoders and seven-bit shift registers, including over 100 organic electrochemical transistors each, thus minimizing the number of terminals required to drive monolithically integrated all-printed electrochromic displays. These relatively advanced circuits are enabled by a reduction of the transistor footprint, an effort which includes several further developments of materials and screen printing processes. Our findings demonstrate that digital circuits based on organic electrochemical transistors (OECTs) provide a unique bridge between all-printed organic electronics (OEs) and low-cost silicon chip technology for Internet of Things applications.
Printed organic electronics (OE), in the form of sensors1,2,3, actuators4,5,6, and displays7,8,9, have been manufactured using printing techniques on flexible or stretchable carriers to enable distributed monitoring and safety functions on packages, in smart labels, in artificial skin applications, and more10,11,12. Organic solid-state semiconducting devices, relying on charge injection or field-effect charge modulation, represent one important class of relevant devices for internet-of-things (IoT) applications13. These are typically built up from configurations including (ultra-)thin films and/or very narrow distances between electrodes; especially if low-voltage and fast operation is targeted14,15,16,17. Organic field-effect transistors (OFETs) have been explored as sensors and also in various large-scale integrated circuits and they typically operate at voltages beyond 10 V18,19,20 and at frequencies ranging from 103 to 106 Hz21,22,23, thus making relatively swift sensing and signal processing possible. One major drawback with all-printed OFETs, besides high-voltage operation and challenging device structure, is instability or drift of the fundamental threshold voltage24,25,26.
For IoT labels that require massive and reliable signal processing, one or several silicon (Si) chips, typically operating in the range 1.2–3.3 V, are utilized in combination with peripheral, sometimes printed, devices for sensing, actuation, and interfacing27. These chips are archetypally assembled and connected onto the label or item using flip-chip mounting or wiring techniques. The cost of Si-chips is to a great part dominated by the total area of, and the number of process steps to manufacture, the actual Si-dice. For multifunctional applications, several dedicated devices encircle the Si-chip and each requires a unique set of contact pads along the Si-chip (Fig. 1a), which will increase chip area and thus drive costs. In fact, for application-specific integrated circuits (ASIC), such as IoT chips, already beyond just a few contact pads, the chip area is primarily dominated by the number of contact pads, i.e., the design is pad limited rather than core limited. This problem becomes even worse considering that improved silicon manufacturing processes mainly enable core miniaturization, rather than pad miniaturization28. Hence, minimizing the chip area required by the contact pads is of great importance, as this will lower the manufacturing costs (Fig. 1b). Pad limited chip designs typically lead to expensive multifunctional IoT labels, which hampers the implementation of smart labels for desired multipurpose and end-user specific applications in medicine, safety, and security. With printed digital circuits, such as shift registers and binary-coded decimal (BCD) decoders that transfer serial or binary-coded signals into exclusive output terminals, low-cost multifunctional IoT labels based on Si-chips that only need few contact pads would then be feasible.
Organic electrochemical transistors (OECTs) represent another class of printable devices that typically operate at ~1 V, with exceptional threshold voltage stability and high transconductance characteristics29,30,31. These features, along with very robust device architecture and biocompatibility, have made the OECTs suitable for sensing and various bioelectronics applications; as the translator of chemical, physical, and biochemical signals into electrical ones, across the biology-technology gap32,33,34,35. The prime drawbacks of these devices are the relatively slow switching characteristics, in part owing to diffusion of ions, and the need for an electrolyte in the gate configuration; the latter makes miniaturization difficult owing to a relatively large footprint of printed electrolyte features. Few attempts have been reported to realize OECT-based digital circuits36,37,38,39, and the efforts have typically been limited to individual digital gates and active addressing in display matrices40,41,42. Slow switching and a large device footprint, i.e., on the scale of 10–100 ms and 0.1–1 mm2, respectively, which is archetypical for printed OECTs, is not suitable for signal processing but certainly tolerable in decoders, shift registers, and multiplexers. Particularly, this is valid when driving and recording already slow operating and areal devices, such as electrochromic displays, sensors, and actuators, which typically switch and operate at 0.1–10 Hz and are of a size ranging from 0.1 mm2 to 1 cm2.
Here, we report all-printed coplanar OECTs included in a BCD 4-to-7 decoder and a seven-bit shift register, connected to Si-circuitry, to drive a monolithically integrated all-printed electrochromic seven-segment display, based on poly(3,4-ethylenedioxythiophene) doped with poly(styrenesulfonic acid) (PEDOT:PSS). The BCD 4-to-7 decoder, consisting of 87 OECTs, operates as a four-stage combination logic function and reduces the number of pins required on the Si-chip, to drive the display, from 7 to 4. To even further reduce the number of contact pins on the Si-chip, a seven-bit serial-in/parallel-out shift register, which requires only one data input and one clock signal, was designed and printed. The seven-bit shift register consists of seven cascaded Master-Slave D flip-flops based on 114 OECTs in total, thus requiring seven clock cycles to display one digit. Both the shift registers and the BCD decoders are implemented with NAND/NOT logic circuits and are based on the all-printed coplanar OECTs. The NAND/NOT logic implementation relies on a resistor ladder and suffers from logic level decay, owing to the particular characteristics of the PEDOT:PSS-based OECT that operate in depletion mode. However, here we successfully demonstrate correct logic propagation through 29 stages of OECT-based gates in the seven-bit shift registers without significant voltage level decay. This was obtained by increasing the margins of the voltage output levels, enabling cascade-coupling of the logic gates. An increase in voltage margins also implies an elevated risk for device degradation, owing to increased voltage strain between the gate and drain. To lower the voltage strain, the circuit supply voltage was ± 5 V, with a corresponding matching of the resistor values of the ladder. Moreover, a low-voltage strain implies better OECT performance, i.e., lower OFF-current levels, which in turn results in better defined output levels when constructing logic circuits. We further demonstrate the robustness of this technology by monolithically integrating the BCD 4-to-7 decoder with a seven-segment electrochromic display, where screen printing is the sole deposition technique used to manufacture the electronic system. The possibility to develop all-printed large-scale ICs on flexible substrates, operated at low voltages, offers an unreached solution when targeting flexibility in multipurpose applications.
Printed organic electrochemical transistors
The PEDOT:PSS-based OECTs are printed to form a coplanar top-gate configuration (Fig. 2a, b), where a printed solid electrolyte is sandwiched between a bottom channel and a top-gate electrode, allowing for shorter switching times and smaller footprints, as compared with the lateral configuration43. Previously, we have presented two designs of coplanar OECTs, one comprising carbon source/drain electrodes in contact with the electrolyte (denoted as C-C OECT), and one where the carbon source/drain electrodes are isolated from the electrolyte (denoted as P-P OECT)43. The C-C OECTs offer larger ON-current and better switching cyclability, owing to the source and drain carbon contacts suppressing reduction front propagation in the PEDOT:PSS outside the active channel area43. Here, all the logic gates and digital circuits are based on the C-C OECT configuration. The characteristics of a typical printed C-C OECTs are presented in Fig. 1c, d. The ON-current is ~0.5 mA and the ON/OFF ratio is ~105, whereas the switching time is ~20 ms (ON-to-OFF) and ~30 ms (OFF-to-ON), respectively.
Logic gates based on printed electrochemical transistors
Inverters and NAND gates serve as the building blocks of various combinational and sequential OECT-based logic circuits. We have manufactured and tested inverters, two-, three-, and four-input NAND gates, which are the building blocks of the BCD 4-to-7 decoder and the seven-bit shift register, and the results are presented in the following sections. The logic gates are based on OECTs operated in depletion mode and their output voltage levels, upon switching, therefore rely on voltage division of a resistor ladder (R1, R2, and R3). The OECT-based inverters and two-input NAND gates are presented in Fig. 3a, b, whereas three- and four-input NAND gates are described in Supplementary Figs. 1–4. The selection of resistor values, and their mutual relationship, is dependent on the applied supply voltage and the targeted LOW and HIGH output voltage levels along with the resistance of the ON/OFF states of the OECT. The resistance of the OFF-state (ON-state) should preferably be at least ~20 times higher (lower) than R3 to ensure reliable switching (Supplementary Fig. 5). Here, the target values of the resistor ladder are R1 = 40.5 kΩ, R2 = 14 kΩ, and R3 = 30.5 kΩ. These values were obtained through simulations (Supplementary Fig. 6), and offer relatively fast switching with a small RC delay and a sufficient balance between R3 and the resistance value of the corresponding OECT ON-state. Additionally, these values are chosen such that a resistance variation of ~10% would result in an output voltage variation of ~1% (Supplementary Fig. 6a). As shown in Fig. 3c–e, the HIGH and LOW output voltages of such logic gates are typically higher than 1.25 V and lower than 0.15 V, respectively, with LOW and HIGH input voltages of 0.1 V and 1.3 V. Such a small voltage difference between the input and output logic voltage levels ensures correct logic propagation in the cascade-coupled decoders and shift registers.
The operational and layout design requirements for the OECT technology, to serve as the signal switches in the targeted digital circuits, are ON-to-OFF and OFF-to-ON switching times shorter than 30 ms, an ON/OFF-current ratio of at least 400, and miniaturization of the OECT footprint down to ~1 mm2. Together, this should allow for a digital circuit, comprised of ~100 OECTs configured in <30 logic stages, that fits within an area of ~10 cm2 and that performs a complete signal processing task within a (few) second(s). To reach this desired combination of parameters, we redesigned the layout, materials, printing processes, and driving protocol of OECTs circuits, in several aspects, as compared with previous demonstrations39,44. Our earlier position with respect to line widths and layout is shown in Fig. 3f. In the current work, we have increased the sheet resistance (from ~5 kΩ sq–1 to ~25 kΩ sq–1) of the printed resistor material by diluting the resistor ink with ~20% of dielectric ink (Supplementary Fig. 7), and also chosen to utilize a polyarylate screen mesh (offering better resolution) instead of the nylon meshes previously used. The high-resolution screen printing approach enables printing of better resolved features that gives a reduced footprint, which here includes a size reduction of the PEDOT:PSS-based channel, the electrolyte (Supplementary Fig. 8), the dielectric layer defining the electrolyte area and also the via interconnects. Thanks to the fivefold increase in sheet resistance of the resistor ink, the area of each resistor (200 µm linewidth) ladder is reduced by a factor of 5. A detailed description of all materials and printing processes is provided below in the Methods section. In addition, a supply voltage of ± 5 V was applied, which lowers the voltage strain between gate and drain. It is of critical importance to maintain the voltage strain at a low level to obtain fully operational logic gates (Supplementary Fig. 9). The combined improvements, listed above, allows us then to reduce the total footprint of the OECT-based circuits by a factor 12–40 while comparing with prior reports39,44 (Fig. 3g). Footprint reduction not only enables monolithic integration of printed logic circuits and electrochromic displays, at an adequate area ratio, it also implies an improved manufacturing yield, thanks to better deposition accuracy as the circuits are manufactured on a smaller area.
BCD 4-to-7 decoder
A BCD 4-to-7 decoder enables an update of a seven-segment display, e.g., a counting sequence from ‘0’ to ‘9’, by only using four input signals, instead of seven input signals when addressed directly. Here, the decoder, purely designed and based on OECT NAND gates and inverters, is presented in Fig. 4a, b. The decoder, which is a four-stage logic circuit, consists of 87 OECTs, 108 resistors, and >200 via interconnects. Figure 4c shows the logic voltage output sequence (red solid line, VPE) that controls the update sequence of the pixel electrode of segment a (see inset to Fig. 4c for a definition of segments a–g in a seven-segment display) when the input signals DataIN1 to DataIN4 correspond to the digits [0–9]. The data shown by the black solid line is the logic voltage output sequence that controls the counter electrode of segment a (VCE). For each digit, segment a shows the correct logic voltage level. All seven nodes a–g are tested to show correct functionality, more details can be found in the Supplementary Figs 10–15. The largest benefit of using the decoder is the small propagation delay, which is in total only 150 ms, whereas the seven-bit shift register presented below needs to process seven clock cycles, thus making it slower. The propagation delay was further investigated by cascade-coupling five printed OECT-based inverters into a ring oscillator circuit. After 60 s of continuous self-oscillations, the voltage output was varying between 0.55 V and 1.35 V at a frequency of ~1 Hz, which corresponds to ~100 ms propagation delay per stage of the ring oscillator circuit.
Seven-bit shift register
The attractive functional feature of a shift register is that only one input signal terminal, together with a clock signal, is required to produce a signal pattern on an arbitrary number of parallel output terminals. The key building blocks of shift registers are the D flip-flops (Fig. 5a), which transfer the input data at the D-terminal to the outputs Q and QINVERSE for every clock cycle. A Master-Slave D flip-flop (Fig. 5a, b), based on OECTs, is built with eight two-input NAND gates. Cascading seven D flip-flop circuits, and adding two inverters to the first flip-flop circuit, results in a seven-bit shift register configuration (Fig. 5a–c), consisting of 114 OECTs, 174 carbon resistors, and over 400 via interconnects, which are all screen printed on a flexible substrate. Figure 5d presents the voltage outputs at nodes g and a, which are the first (Q1) and the seventh (Q7) parallel outputs in the shift register, respectively. In this test, the input signal Q is alternating between ‘0’ and ‘1’, and shifting of bits is triggered by a clock pulse every 6th second. It can be observed that the voltage signal at node g follows that of node a after exactly seven clock cycles. The logic level difference between node a and node g is only 0.1 V, and such low deterioration of the voltage levels ensures further logic propagation. Previous work on a two-bit shift register, based on lateral OECTs, suggests failure of the logic propagation in shift registers having six bits, or more, owing to logic level decays44. A video (Supplementary Movie 1) was recorded to show the signal ‘0’ propagating along all the output nodes, from node g to node a. The propagation of the ‘0’ input signal is shown on seven individual all-printed electrochromic displays45, which further demonstrates the compatibility between printed OECT-based logic circuits and external printed interface circuits.
Furthermore, we used the shift register to mimic the update of a printed seven-segment electrochromic display, which implies that for example the digit ‘4’ can be shown on the display by providing seven clock pulses and the input pattern [0,1,1,0,0,1,1]. The voltage at node g (Q1) is presented in Fig. 5e when the above input pattern is shifted in, thus showing the correct logic levels throughout the whole-display update sequence. This was verified for all 10 digits [0–9]. By recording the logic voltage level at node g, the correct logic functionality of all 70 bits required for the display update sequence is demonstrated (Supplementary Figs. 16–20). Figure 5f shows the actual voltages that are measured when the input pattern [0,1,1,0,0,1,1] has been delivered to the parallel outputs interfacing with an external electronic circuit, in this case the pixel electrodes of all seven segments [a–g] of a printed electrochromic display. Segments exposed to a digital HIGH level at their respective output [b, c, f, g] are switched to ~− 1 V by the display driver circuitry (− 1 V is the display supply voltage that enables coloration of those segments), whereas the remaining segments [a, d, e] are kept at ~0 V, which corresponds to the digit ‘4’.
The robustness of the technology was further demonstrated by monolithic integration of OECT-based logic circuits and electrochromic displays, thereby forming an electronic system where screen printing solely is used as the deposition technique in the manufacturing process. The OECT architecture resembles the electrochromic display architecture; an electrolyte sandwiched between either the OECT channel and the gate electrode of the transistor, or between the pixel electrode and the counter electrode of the electrochromic display. Hence, the inclusion of a printed electrochromic display does not involve any additional processing steps. This concept was demonstrated by combining a seven-segment display with the BCD 4-to-7 decoder described earlier (Fig. 6). A video (Supplementary Movie 2) shows the full counting sequence [0–9] of the electrochromic display upon addressing the BCD 4-to-7 decoder with the corresponding binary input sequences [0000–1001]. Note that the colors of the segments might seem inverted, i.e., the ON-state is white and the OFF-state is blue, in Fig. 6 and Supplementary Movie 2, owing to omission of a blue-colored graphic shutter layer in the manufacturing process.
The seven-bit shift register of the all-printed coplanar OECTs requires 114 transistors and 29 stages of logic propagation. This number of integrated OECTs is about one order of magnitude higher when compared with the number of transistors included in any other previous attempts to obtain (printed) OECT-based logic circuits. This achievement is attributed to a footprint reduction of the printed circuits by at least a factor of 12 when compared with previous reports. All individual components (OECTs, resistors, via interconnects and display segments) need to be functional in order to obtain a fully operational printed electronic system, hence, this also gives an indication of the robustness of the technology. The large-scale IC demonstrates the potential of all-printed OECT-based circuits for a great variety of applications, for example, in matrix-addressing, and (de)multiplexing of signals with increased number of rows and columns, also targeting counters, decoders, etc. In a hybrid electronics system, combining silicon-based electronics and printed electronics, the capability to implement complex functionalities of large-scale printed systems shares the workload of the silicon chips, and significantly reduces the functionalities and the number of pins required for the silicon chip, thus greatly improving cost efficiency. For instance, with an 8-pin microcontroller that costs < 1 US$, it is then possible to drive all-printed multidigit seven-segment displays without losing the ability of sensor signal acquisition and processing. The ability to print low-voltage large-scale circuits on flexible substrates also enables many IoT applications, such as smart sensor labels, tags, sticks, signages, etc., on various substrates, e.g., conformable substrates, paper, and cloth. In combination with an array of sensors, a wearable device based on the presented technology could be developed for further diagnostic purposes, e.g. to monitor temperature, blood oxygen, or health status parameters expressed in sweat, on human skins.
In summary, we have developed and manufactured, by using only screen printing processing, all-printed large-scale integrated circuits (4-to-7 decoder and seven-bit shift register) from coplanar top-gate PEDOT:PSS-based OECTs. The OECTs exhibit relatively fast switching, small footprint, excellent uniformity and a simple manufacturing route. Logic gates, including inverters and NAND gates, were investigated as the building block of the large-scale circuits. We demonstrated that both the 4-to-7 decoder and the seven-bit shift register deliver correct logic functionalities. In addition, the capability to drive all-printed electrochromic displays is shown, either with standalone or monolithically integrated electrochromic displays. The technology of all-printed large-scale ICs on flexible substrates, operated at low voltages, offers an ultra-low-cost solution for many IoT applications.
The plastic substrate of polyethylene terephtalate (PET) Polifoil Bias is purchased from Policrom Screen. PEDOT:PSS Clevios SV3, purchased from Heraeus, serves as the electrochemically active transistor channel and gate electrodes, as well as the pixel and counter electrodes of the electrochromic displays. The electrolyte AFI VV009, which is based on poly(diallyldimethylammonium chloride) dissolved in water, solid particles providing opacity, initiator molecules and binder molecules capable of forming a cross-linked network through radical polymerization upon UV light irradiation, is provided by RISE Acreo on commercial terms. The screen printable and UV-curable electrolyte is used for both OECTs and electrochromic displays. Carbon ink 7102 and 7082 printing pastes (purchased from DuPont) are used for drain/source contacts (to minimize the reduction front) and printed resistors, respectively. To obtain printed resistors with approximately five times higher sheet resistance, and thereby lower the footprint of the printed resistors, the 7082 paste was diluted by adding ~20% of the 5036 paste from DuPont (Supplementary Fig. 7). Silver ink (Ag 5000 purchased from DuPont) and insulating ink (5018 purchased from DuPont) are used for printed interconnects and isolation, respectively.
Manufacturing of OECTs, circuits, and electrochromic displays
All materials were deposited by flatbed sheet-fed screen printing equipment (DEK Horizon 03iX) on top of PET plastic substrates, the printed features of the design layout cover approximately the area of an A4 sheet. The screen printing tools, V-screens provided by PVF, were based on polyarylate threads. The DEK Horizon 03iX, which has a process alignment capability of ±25 µm, in combination with the high-quality screen printing tools ensure high manufacturing yield by that uniform alignment accuracy across the whole substrate area is obtained; misalignment or ink smearing by > ~50 µm will inevitably result in malfunctioning devices and circuits. Ag 5000 silver ink is first deposited on the substrate as contact pads and interconnect wires. A layer of PEDOT:PSS is then patterned between the silver contact pads to form the transistor channel, followed by the carbon electrodes, resulting in an active channel area of 100 × 150 µm2. The PEDOT:PSS layer is simultaneously deposited to form the display pixel electrode layer. The silver, the PEDOT:PSS and the carbon inks are all dried at 120 °C for 5 min. An insulating layer of 5018 ink is then deposited and UV-cured to define the area of the subsequently deposited gate electrolyte. The electrolyte required to enable the display functionality is deposited in the same print step. Another layer of PEDOT:PSS is deposited on the electrolyte patterns as the gate electrodes and the display counter electrodes. The resistors in the circuits are formed by the carbon ink 7082. The crossings of interconnects are created by the deposition of the insulating 5018 ink followed by the deposition of Ag 5000, the latter also forms the conductors of the display device.
Characterization of OECTs and circuits
All measurements are performed in a controlled environment at a temperature of ∼20 °C and at a relative humidity of ∼45% RH. Transfer and dynamic switch measurements were performed by using a semiconductor parameter analyser (HP/Agilent 4155B) and a function generator (Agilent 33120A). The printed circuits were characterized by using a data acquisition card (DAQ card PCI-6723 from National Instruments). The voltage supply [VDD, VSS] for the logic gates, 4-to-7 decoders, and seven-bit shift registers is [+5 V, −5 V], whereas the voltage supply for the electrochromic displays was − 1 V (Fig. 5f) or − 1.5 V (Fig. 6 and Supplementary Movies 1 and 2). The input signals controlling the printed circuits were also supplied by the DAQ card, and the frequency was varied for the different circuits being characterized. One hertz was used for standalone OECTs, inverters and NAND gates, whereas lower frequencies were used for the more complex 4-to-7 decoder (digits updated every two seconds) and seven-bit shift register circuits (new clock pulse every 6th second) to provide sufficient time to ensure complete propagation of the input signals through all OECTs within the circuits. Higher switching frequencies could possibly have been used, especially for the seven-bit shift register circuit, but no attempts to determine the frequency limits of the circuits have been conducted.
The data that support the findings of this study are available from the corresponding author upon request.
Khan, Y., Ostfeld, A. E., Lochner, C. M., Pierre, A. & Arias, A. C. Monitoring of vital signs with flexible and wearable medical devices. Adv. Mater. 28, 4373–4395 (2016).
Rim, Y. S., Bae, S.-H., Chen, H., De Marco, N. & Yang, Y. Recent progress in materials and devices toward printable and flexible sensors. Adv. Mater. 28, 4415–4440 (2016).
Lochner, C. M., Khan, Y., Pierre, A. & Arias, A. C. All-organic optoelectronic sensor for pulse oximetry. Nat. Commun. 5, 5745 (2014).
Son, D. et al. Multifunctional wearable devices for diagnosis and therapy of movement disorders. Nat. Nanotechnol. 9, 397 (2014).
Sekitani, T. & Someya, T. Stretchable, large-area organic electronics. Adv. Mater. 22, 2228–2246 (2010).
Bauer, S. et al. 25th anniversary article: a soft future: from robots and sensor skin to energy harvesters. Adv. Mater. 26, 149–162 (2014).
Sekitani, T. et al. Stretchable active-matrix organic light-emitting diode display using printable elastic conductors. Nat. Mater. 8, 494 (2009).
Zheng, H. et al. All-solution processed polymer light-emitting diode displays. Nat. Commun. 4, 1971 (2013).
Berggren, M., Nilsson, D. & Robinson, N. D. Organic materials for printed electronics. Nat. Mater. 6, 3–5 (2007).
Someya, T. et al. Conformable, flexible, large-area networks of pressure and thermal sensors with organic transistor active matrixes. Proc. Natl. Acad. Sci. USA 102, 12321–12325 (2005).
Tobjörk, D. & Österbacka, R. Paper electronics. Adv. Mater. 23, 1935–1961 (2011).
Sokolov, A. N., Tee, B. C. K., Bettinger, C. J., Tok, J. B. H. & Bao, Z. Chemical and engineering approaches to enable organic field-effect transistors for electronic skin applications. Acc. Chem. Res. 45, 361–371 (2012).
Yang, G. et al. A Health-IoT platform based on the integration of intelligent packaging, unobtrusive bio-sensor, and intelligent medicine box. IEEE T. Ind. Inform. 10, 2180–2191 (2014).
Yang, S. Y., Kim, S. H., Shin, K., Jeon, H. & Park, C. E. Low-voltage pentacene field-effect transistors with ultrathin polymer gate dielectrics. Appl. Phys. Lett. 88 173507 (2006).
Elsobky, M. et al. A digital library for a flexible low-voltage organic thin-film transistor technology. Org. Electron. 50, 491–498 (2017).
Ishida, K. et al. Stretchable EMI measurement sheet with 8x8 coil array, 2 V organic CMOS decoder, and 0.18µm silicon CMOS LSIs for electric and magnetic field detection. IEEE J. Solid-State Circuits 45, 249–259 (2010).
Elsobky, M. et al. Ultra-thin smart electronic skin based on hybrid system-in-foil concept combining three flexible electronics technologies. Electron. Lett. 54, 338–340 (2018).
Kawaguchi, H., Someya, T., Sekitani, T. & Sakurai, T. Cut-and-paste customization of organic FET integrated circuit and its application to electronic artificial skin. IEEE J. Solid-State Circuits 40, 177–185 (2005).
Crone, B. et al. Large-scale complementary integrated circuits based on organic transistors. Nature 403, 521 (2000).
Ng, T. N. et al. Scalable printed electronics: an organic decoder addressing ferroelectric non-volatile memory. Sci. Rep. 2, 585 (2012).
Baeg, K. J., Caironi, M. & Noh, Y. Y. Toward printed integrated circuits based on unipolar or ambipolar polymer semiconductors. Adv. Mater. 25, 4210–4244 (2013).
Gelinck, G. H. et al. Flexible active-matrix displays and shift registers based on solution-processed organic transistors. Nat. Mater. 3, 106–109 (2004).
Bucella, S. G. et al. Macroscopic and high-throughput printing of aligned nanostructured polymer semiconductors for MHz large-area electronics. Nat. Commun. 6, 8394 (2015).
Tang, W. et al. Bias stress stability improvement in solution-processed low-voltage organic field-effect transistors using relaxor ferroelectric polymer gate dielectric. IEEE Electron Device Lett. 38, 748–751 (2017).
Noh, J. et al. Key issues with printed flexible thin film transistors and their application in disposable RF sensors. Proc. IEEE 103, 554–566 (2015).
Sirringhaus, H. 25th anniversary article: organic field-effect transistors: the path beyond amorphous silicon. Adv. Mater. 26, 1319–1335 (2014).
De Donno, D., Catarinucci, L. & Tarricone, L. RAMSES: RFID augmented module for smart environmental sensing. IEEE T. Instrum. Meas. 63, 1701–1708 (2014).
Holweg, G. Infineon Technologies Austria AG, Personal communication.
White, H. S., Kittlesen, G. P. & Wrighton, M. S. Chemical derivatization of an array of three gold microelectrodes with polypyrrole: fabrication of a molecule-based transistor. J. Am. Chem. Soc. 106, 5375–5377 (1984).
Nilsson, D. et al. Bi-stable and dynamic current modulation in electrochemical organic transistors. Adv. Mater. 14, 51–54 (2002).
Rivnay, J. et al. Organic electrochemical transistors. Nat. Rev. Mater. 3, 17086 (2018).
Berggren, M. & Richter-Dahlfors, A. Organic bioelectronics. Adv. Mater. 19, 3201–3213 (2007).
Rivnay, J., Owens, R. M. & Malliaras, G. G. The rise of organic bioelectronics. Chem. Mater. 26, 679–685 (2014).
Someya, T., Bao, Z. & Malliaras, G. G. The rise of plastic bioelectronics. Nature 540, 379 (2016).
Simon, D. T., Gabrielsson, E. O., Tybrandt, K. & Berggren, M. Organic bioelectronics: bridging the signaling gap between biology and technology. Chem. Rev. 116, 13009–13041 (2016).
Nilsson, D., Robinson, N., Berggren, M. & Forchheimer, R. Electrochemical logic circuits. Adv. Mater. 17, 353–358 (2005).
Rothlander, T. et al. Nanoimprint lithography-structured organic electrochemical transistors and logic circuits. IEEE T. Electron Dev. 61, 1515–1519 (2014).
Svensson, P.-O., Nilsson, D., Forchheimer, R. & Berggren, M. A sensor circuit using reference-based conductance switching in organic electrochemical transistors. Appl. Phys. Lett. 93, 203301 (2008).
Andersson Ersman, P. et al. Screen printed digital circuits based on vertical organic electrochemical transistors. Flex. Print. Electron. 2, 045008 (2017).
Andersson, P. et al. Active matrix displays based on all-organic electrochemical smart pixels printed on paper. Adv. Mater. 14, 1460–1464 (2002).
Andersson, P., Forchheimer, R., Tehrani, P. & Berggren, M. Printable all-organic electrochromic active-matrix displays. Adv. Funct. Mater. 17, 3074–3082 (2007).
Zirkl, M. et al. An all-printed ferroelectric active matrix sensor network based on only five functional materials forming a touchless control interface. Adv. Mater. 23, 2069–2074 (2011).
Andersson Ersman, P., Nilsson, D., Kawahara, J., Gustafsson, G. & Berggren, M. Fast-switching all-printed organic electrochemical transistors. Org. Electron. 14, 1276–1280 (2013).
Hütter, P. C., Rothländer, T., Scheipl, G. & Stadlober, B. All screen-printed logic gates based on organic electrochemical transistors. IEEE T. Electron Dev. 62, 4231–4236 (2015).
RISE, Electrochromic systems and displays, www.ri.se/en/expertise/electrochromic-displays (Accessed: 3rd October 2019).
This project was financially supported by the Swedish Foundation for Strategic Research (SE13–0045 and RIT15-0119), the Knut and Alice Wallenberg Foundation (2012.0302), the Önnesjöstiftelsen, VINNOVA and the Swedish Research Council (2016-03979). We thank DI Gerald Holweg, Pre Development Manager at Infineon Technologies Austria AG, for valuable discussions. Open access funding provided by Linköping University.
Acreo AB filed a patent application related to the electrolyte used in this work, through the World Intellectual Property Organization, international publication number WO 2012/136781, filed on 5 April 2012, granted on 19 June 2018 with patent number US 10001690B2. P.A.E. and M.B. filed a patent application via Acreo AB, through the World Intellectual Property Organization, international publication number WO 2011/042430, filed on 5 October 2010, granted on 19 August 2014 with patent number US 8810888B2. All other authors declare no competing interests.
Peer review information Nature Communications thanks Robert McLeodand and the other, anonymous, reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Andersson Ersman, P., Lassnig, R., Strandberg, J. et al. All-printed large-scale integrated circuits based on organic electrochemical transistors. Nat Commun 10, 5053 (2019). https://doi.org/10.1038/s41467-019-13079-4
Solid-State Organic Electrolyte-Gated Transistors Based on Doping-Controlled Polymer Composites with a Confined Two-Dimensional Channel in Dry Conditions
ACS Applied Materials & Interfaces (2021)
ACS Applied Materials & Interfaces (2021)
Enhancing the Electrochemical Doping Efficiency in Diketopyrrolopyrrole‐Based Polymer for Organic Electrochemical Transistors
Advanced Electronic Materials (2021)
Advanced Engineering Materials (2021)
Strategy for Selective Printing of Gate Insulators Customized for Practical Application in Organic Integrated Devices
ACS Applied Materials & Interfaces (2021)