Skip to main content

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Optimizing radionuclide sequestration in anion nanotraps with record pertechnetate sorption

Abstract

The elimination of specific contaminants from competitors poses a significant challenge. Rather than relying on a single direct interaction, the cooperation of multiple functionalities is an emerging strategy for adsorbents design to achieve the required affinity. Here, we describe that the interaction with the target species can be altered by modifying the local environment of the direct contact site, as demonstrated by manipulating the affinity of pyridinium-based anion nanotraps toward pertechnetate. Systematic control of the substituent effect allows the resulting anion nanotraps to combine multiple features, overcoming the long-term challenge of TcO4 segregation under extreme conditions of super acidity and basicity, strong irradiation field, and high ionic strength. The top material exhibits the highest sorption capacity together with record-high extraction efficiencies after a single treatment from conditions relevant to the used nuclear fuel (Hanford tank wastes, 95%) and legacy nuclear wastes (Savannah River Sites, 80%) among materials reported thus far.

Introduction

Nuclear fission is a mature technology that can make a vital contribution toward global low-carbon energy needs1,2,3,4,5,6. However, opposition over the safety and security of nuclear facilities and materials still remains and needs to be addressed if new nuclear facilities are to gain widespread acceptance. Much of the controversy surrounding nuclear power stems from the early days of industrial development and the Cold War arms race, which has left a legacy of contaminated sites that must be cleaned up7,8,9. In addition, the development of nuclear technologies has led to many cases of accidental and intentional release, with the accumulation of significant levels of radionuclides in the environment10,11,12. One potentially troublesome radionuclide is technetium-99 (99Tc), a considerable fraction of which occurs as pertechnetate, TcO4. This species, with a long half-life of 213,000 years, is highly mobile in groundwater and biological systems, leading to possible problematic spread of radiotoxic material following containment breaches13,14,15,16. In addition, the volatile nature of some 99Tc compounds (e.g., Tc2O7), generated during high-temperature vitrification of the nuclear waste, makes 99Tc problematic in the off-gas system design for vitrification facilities17. To this end, 99Tc management is important both in terms of ensuring safe disposal of radioactive waste from power generation, minimizing the off-site migration of the contaminated groundwater, and assisting in cleanup efforts of legacy waste sites, yet it remains an unmet challenge17,18.

To address this need, recent efforts have focused on developing ion-exchange sorbents given their ease of implementation and high 99Tc recovery rate19,20,21,22,23,24. While elegant examples of materials embodying this strategy are now known, the battle to ameliorate 99Tc contamination is far from finished. Current industrial extraction technologies suffer from relatively low affinity and kinetics, as well as limited capacity for TcO4. Given this, proper remediation of the legacy tank wastes is still pending. These facts underscore the need for material innovation capable of extracting radionuclides from complex media for environmental remediation and in order to close the nuclear fuel cycle.

Nature has been subject to millions of years of evolutionary experimentation to recognize specific metal ions with high sensitivity, whereby multiple functionalities are assisted with the direct binding sites. Chemical efforts to mimic such partnership have led to numerous advances in control of binding affinity. As a sophisticated example, supramolecular techniques have been utilized to engineer cations with intriguing properties that display particular innovation and hold promise as potential game-changing technologies in the field of target ion extraction. The selectivity emerges from the concerted efforts of the binding partners25,26,27. Thus, it is well conceivable that some structural modifications to a site separate from the place of direct contact of the association partners may well affect their binding strength, thereby providing the needed ability to recognize target anions under highly competitive conditions. While success was encountered using these receptors in the context of a classic liquid–liquid extraction approach, to meet the challenges posed by the immense volumes of wastewater, sorbent materials would allow for an increase in operational ability28,29,30,31,32,33,34. With these in mind, we envisioned that if distinct functionalities can be incorporated into a highly porous cationic framework, this may enable a new level of control over ion pair recognition and extraction efficiency within a sorbent material with a high density of readily accessible ion-exchange sites. This is also anticipated to afford new anion receptors with fast kinetics together with high uptakes, which surmount the prime issues of low efficiency encountered by commercial resins as a result of low surface area and low density of accessible ion-exchange groups.

To explore the validity of this hypothesis, we were motivated by the exploration of porous organic polymers (POPs) for this ambitious task. This class of porous material has moved to the forefront of materials research due to their modular nature. POPs exhibit tailorable porosity and tunable functionality, and are well-suited for a wide range of applications including gas storage/separation, catalysis, hazard contaminants removal, and sensing, to name a few35,36,37,38,39,40,41. The potential to deploy POPs as solid extractors is related to the ease of tunability with regard to their composition42,43,44. In this contribution, we chose pyridinium as the cation building unit to demonstrate the proof-of-concept, given its chemical stability, amenable synthesis, together with easy-to-get properties45. To optimize the anion exchange performance and to establish the structure-property relationships, different anchor groups were de novo introduced (Fig. 1). In addition, to improve the uptake capacity and efficiency of the resultant anion nanotraps, porous sorbent materials were constructed by the functional pyridinium moieties alone, to conserve a sufficiently high density of accessible exchange sites. Therefore, the resultant materials combine the advantages of high uptake capacity, selectivity, and removal rate of TcO4/ReO4 ions, making them promising for decontamination of polluted water and remediation of nuclear waste. Through detailed studies, we showed that the adsorbent constructed with a dimethylamino group in the para position relative to pyridinium displayed extraordinary affinity for TcO4 with a record-breaking uptake capacity and selectivity under extreme conditions of super acidity and basicity, as well as high concentrations of competitors. These insights are meant to guide further research, which should be devoted to increasing the binding affinity of adsorbents toward target ions.

Fig. 1
figure1

Anion nanotraps for TcO4 removal. Illustration of optimizing pyridinium based anion nanotraps for TcO4 recognition inspired by supramolecular technology

Results

Material synthesis

To target the desired materials, our initial step was to construct pyridine moieties with various anchor groups into porous frameworks, due to the low solubility of pyridinium in organic solvents, which is detrimental to yield highly porous polymers. To construct these moieties into porous polymers, we decided to use free radical induced polymerization with the following considerations: (i) the resultant highly cross-linked polymer chains and thus the rigidity of the matrix, reduce the ability of the pyridinium to congregate in hydrated domains, which decrease the affinity for more hydrated anions and thereby enhance the selectivity for less hydrated anions such as TcO446; and (ii) the adapted synthesis allows for the introduction of hierarchical porosity in the resultant polymers, which is expected to enhance the kinetics, thereby offering an opportunity to meet the challenges posed by the vast volumes of wastewater47,48. To this end, we further functionalized the pyridine moieties with vinyl groups, affording V-Py, V-pNH2Py, and V-pN(Me)2Py, respectively (Table 1). Under solvothermal conditions in dimethylformamide (DMF) at 100 °C, polymerization of these monomers in the presence of azobisisobutyronitrile (AIBN) gave rise to the porous pyridine-based polymers in quantitative yields, which were denoted as POP-Py, POP-pNH2Py, and POP-pN(Me)2Py, respectively. To introduce ion-exchange sites, the pyridine moieties in the resultant materials underwent a quaternization reaction with methyl iodide (CH3I), yielding the porous ionic organic polymer of polymerized quaternary ammonium (PQA) salt PQA-Py-I, PQA-pNH2Py-I, and PQA-pN(Me)2Py-I, respectively.

Table 1 Structure of building units and textural parameters of various pyridinium functionalized hierarchical porous polymers

Among the synthesized porous materials, POP-pN(Me)2Py and corresponding quaternization product PQA-pN(Me)2Py-I were chosen as representative samples for thorough illustration. As probed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), it is revealed that no noticeable morphological changes occurred after quaternization, both POP-pN(Me)2Py and PQA-pN(Me)2Py-I feature aggregates comprising interconnected nanoparticles with sizes of 50–100 nm (Supplementary Fig. 1 and 2). Structural details of these materials were elaborated by solid-state 13C NMR spectroscopy. As seen in Supplementary Fig. 3, the characteristic vinyl 13C resonance located in the range of 100.0–110.0 ppm in the monomers disappears with the concomitant appearance of the polymerized vinyl group peak at 31.8 ppm, confirming the conversion of the monomer into the respective polymer48. In addition, the increased relative intensity of the peak at 44.9 ppm, ascribed to the methyl group from iodomethane (CH3I), verified the occurrence of the quaternization reaction between the pyridine moiety on POP-pN(Me)2Py and CH3I. To provide additional proof, we employed X-ray photoelectron spectroscopy (XPS). The appearance of strong signals of iodine species at 629.3 and 617.8 eV for I3d5/2 and I3d7/2, respectively, confirmed the success of this transformation (Supplementary Fig. 4). To quantify the degree of quaternization, we evaluated the content of iodine species in PQA-pN(Me)2Py-I by elemental analysis. The results showed that the weight percentage of iodine species in PQA-pN(Me)2Py-I was 38.3 wt% (Supplementary Table 1), which means about 95% of the pyridine moieties were involved in the quaternization reaction, revealing the high throughput of this reaction. The details of the pore properties of the resultant materials were investigated by N2 sorption isotherms collected at 77 K. It is shown that both samples exhibit type-I plus type-IV sorption curves, suggesting the retention of the pore structure (Supplementary Fig. 5). A steep step in the curve at relative pressure (P/P0) less than 0.01 is due to the filling of micropores, whereas a hysteresis loop at P/P0 in the range of 0.45~ 0.95 is mainly from the contribution of the sample mesoporosity, which was also verified by the pore size distribution49. The calculated specific surface areas were 535 and 223 m2g−1 for POP-pN(Me)2Py and PQA-pN(Me)2Py-I, respectively. The decreased surface area can be reasonably attributed to the increased mass after the functionality addition. The details of the characterization of POP-Py and POP-pN(Me)2Py, as well as their corresponding quaternization products are provided in the Supplementary Information (Supplementary Figs. 613).

Sorption isotherms

The full availability of ion exchange sites within the pores of these materials is indicated by a complete anion-exchange process between I and Cl, which was verified by TEM-EDS mapping and XPS analyses (Supplementary Figs. 1417). This feature spurred their exploration for radionuclide polluted water treatment. Sorption experiments were first performed to evaluate the working capacities of these materials. Due to the limited availability and the rarity of the purified isotope 99Tc, combined with its highly radioactive nature, perrhenate (ReO4) was first used as a nonradioactive surrogate for pertechnetate (99TcO4) given their similarities in both magnitude and trend between the solubilities50. The amounts of rhenium species enriched by these materials as a function of its concentration in the supernatant at the equilibrium state were determined by varying the initial concentrations from 25 to 800 ppm with a material-to-solution ratio of 0.5 mgmL−1. An overnight reaction time was used to ensure that the ion exchange reached equilibrium. Results indicate that the equilibrium adsorption data of ReO4 appeared to follow the Langmuir isotherm model (Fig. 2a); sorption increases rapidly at low ReO4 concentrations and slows appreciably as the sorption capacity of the adsorbent is approached, yielding high correlation coefficients (R2 > 0.99). Exchange capacities up to 936, 806, and 1127 mg of ReO4 per gram of polymer were observed for PQA-Py-Cl, PQA-pNH2Py-Cl, and PQA-pN(Me)2Py-Cl, respectively, almost 20 times that observed for the unmodified counterparts (POP-Py, POP-pNH2Py, and POP-pN(Me)2Py), affording 53, 46, and 37 mgg−1, respectively. Given the greatly enhanced performances after quaternization, we establish that the high density of the ion exchange sites on the polymer backbone is the fundamental contributor to their high working capacities and the mechanism for uptake of ReO4 is thus believed to be predominantly ion exchange.

Fig. 2
figure2

ReO4- adsorption isotherms and kinetics investigations. a ReO4- sorption isotherms for various adsorbents. The lines are fit with the Langmuir model; all the fits have R2 values higher than 0.99. b The kinetics of ReO4 adsorption from aqueous solution with an initial concentration of 50 ppm, at a phase ratio (V/m) of 25000 mLg−1. c ReO4- removal kinetics with an initial concentration of 1000 ppb at a V/m ratio of 5000 mLg−1. Source data are provided as a Source Data file

The high extraction capacities for these materials prompted us to evaluate their ion exchange kinetics, which were determined from distilled water samples spiked with 50 ppm of rhenium in the form of ReO4. Remarkably, when the solutions were treated with these materials at a phase ratio of 25000 mLg-1, extremely rapid ion exchange and high uptake were recognized. All three materials reached their equilibrium exchange capacities within 60 min and in particular, 95.3% removal was achieved after 5 min for PQA-pN(Me)2Py-Cl (Fig. 2b). This is in stark contrast to the lengthy contact times required for many sorbent materials, which routinely range from several hours to as much as several days51. The fast kinetics should be an advantage for the continuous treatment of relatively large volumes of slightly contaminated water. We surmise that the impressive uptake capacity along with the fast removal rate is due to the high density of ion-exchange sites and intrinsic porosities allowing for rapid diffusion of ReO4 throughout the materials. Notably, in addition to rapid saturation, PQA-pN(Me)2Py-Cl also possessed a higher capacity, yielding an equilibrium value of 997 mgg−1, in comparison with 849 and 642 mgg−1 afforded by PQA-Py-Cl and PQA-pNH2Py-Cl, respectively, positioning PQA-pN(Me)2Py-Cl as the material with the highest ReO4 uptake among all adsorbents reported so far (Fig. 2b and Supplementary Table 2). Intriguingly, the increase in gravimetric capacity in going from PQA-pN(Me)2Py-Cl to PQA-Py-Cl and PQA-pNH2Py-Cl is opposite to what would be expected from the density of ion-exchange sites. For instance, on the basis of elemental analysis, it was found to have a Cl species content of 10.3, 11.1, and 12.5 wt%, for PQA-pN(Me)2Py-Cl, PQA-Py-Cl, and PQA-pNH2Py-Cl, respectively (Supplementary Table 3). We therefore attribute this anomalous increase in ReO4 uptake capacity for PQA-pN(Me)2Py-Cl to the higher electrostatic ion-pairing attraction energies between the cationic polymer backbone of PQA-pN(Me)2Py-Cl and ReO4 ions. To rationalize this assumption, we measured the distribution coefficient values (Kd, for definition, see the Experimental Section) of these materials toward ReO4. Under the conditions of 10 ppm rhenium with a V/m of 1000 mL g-1, the Kd values were calculated and found to equal 1.13 × 106 (8.82 ppb), 5.44 × 105 (18.35 ppb), and 1.00 × 107 (1.00 ppb) for PQA-Py-Cl, PQA-pNH2Py-Cl, and PQA-pN(Me)2Py-Cl, respectively (number given in parentheses is the residual rhenium concentration), with PQA-pN(Me)2Py-Cl showing almost more than an order of magnitude improvement in performance over the other two, indicative of its stronger affinity toward ReO4 and thereby facilitating the ion exchange between Cl and ReO4.

Next, we assessed selectivity over common anions. The material’s ability to competitively maintain efficiencies and rapid extraction rates at sub ppm levels, more typical of exposure cases, is one of the most important factors when evaluating a material for water treatment applications. Given the high environmental mobility, any accidental leaching of TcO4 poses a real threat to groundwater contamination and aquatic life forms. As such, to access the ion-exchange properties associated with these materials, treatability studies were carried out using groundwater spiked with 1000 ppb of rhenium to simulate the contaminated water from on-site and off-site wells. PQA-pN(Me)2Py-Cl was shown to remove >99.8% of ReO4 from the groundwater, bringing rhenium concentrations to 1.2 ppb, implying that the interferences commonly found in surface waters have a minimal effect on its performance. It is worth mentioning that the residual rhenium concentrations treated by PQA-pN(Me)2Py-Cl are 8 and 15 times lower than that of PQA-Py-Cl and PQA-pNH2Py-Cl, respectively (Fig. 2c). In addition to the impressive removal efficiency, it is outstanding from the viewpoint of kinetic efficiency, reaching the equilibrium exchange capacity within 20 min and over 99.7% of the rhenium species removed within 5 min These results highlight the vast potential of PQA-pN(Me)2Py-Cl in accomplishing radionuclide removal from groundwater.

Encouraged by the results above, we then evaluated wastewater samples. Compared to surface water samples, wastewater is often comprised of fewer competing ions but significantly higher concentrations. Given this, to evaluate the sorption selectivity of ReO4 against the major anions NO3 or SO42–, we performed binary exchange reactions by varying the equivalent ionic fractions of these anions in reactant solutions. A plot of the removal efficiencies of ReO4 against mole fractions of NO3 or SO42– to ReO4 clearly indicated that PQA-pN(Me)2Py-Cl showed a remarkably high tolerance to ReO4 sorption ability in the presence of SO42− and NO3 competition with very high removal efficiencies and excellent Kd(Re) values (Fig. 3). Specifically, at SO42–/NO3: ReO4 molar ratios of 1 to 100, >99.9% of ReO4 ions were sequestered with Kd(Re) values in the range of 1.5×105–6.6×106 mLg-1. It is interesting that even with a tremendous excess of Na2SO4 (SO42–: ReO4 molar ratio at 6000), PQA-pN(Me)2Py-Cl still retained a very good ReO4 removal efficiency (83.4%) and high Kd(Re) value (5034 mL g−1), indicative of an exceptional selectivity of PQA-pN(Me)2Py-Cl for ReO4 against SO42–. This feature makes it an extremely attractive candidate to selectively remove ReO4/TcO4 from waste solutions with high ionic strengths. By contrast, under identical conditions, PQA-Py-Cl and PQA-pNH2Py-Cl afforded ReO4 removal efficiencies of 75.7% and 70.6%, with corresponding Kd(Re) values of 3123 and 2402 mLg−1, respectively, inferior to those for PQA-pN(Me)2Py-Cl (Supplementary Fig. 19).

Fig. 3
figure3

Selectivity evaluation. Effect of competing (a) SO42- and (b) NO3- anions on the anion-exchange of ReO4 by (gray) PQA-Py-Cl, (blue) PQA-pNH2Py-Cl, and (red) PQA-pN(Me)2Py-Cl (lines are guidelines for the eyes). Source data are provided as a Source Data file

Under all conditions tested, the preference of these pyridinium-based sorbents towards ReO4 complexation follows the same order: PQA-pN(Me)2Py-Cl > PQA-Py-Cl > PQA-pNH2Py-Cl. This trend may not be pinpointed to a single property change of the adsorbents but rather as a consequence of a complex interplay of several factors. For example, an increase in surface area may play a key role in the uptake capacity by providing a greater number of exposed exchangeable sites. However, in the present case, only a very weak correlation with the surface area of these materials could be established, thus suggesting that surface area is not the central factor determining the sorption performance; rather, the interaction strength between binding sites and guest species is a more important factor for determining guest uptake. To understand the lack of dependence on the materials’ textural parameters, we investigated the distribution of ReO4 in solid samples. Elemental distribution mapping was performed by SEM. We found homogeneously and densely distributed rhenium species throughout each sample (Supplementary Fig. 20). To examine the binding behavior of ReO4 in these adsorbents, XPS and IR spectroscopy were carried out. Comparison of Re4f signals in the reacted samples (Re@PQA-Py-Cl, Re@PQA-pNH2Py-Cl, and Re@PQA-pN(Me)2Py-Cl), Re@PQA-pNH2Py-Cl and Re@PQA-pN(Me)2Py-Cl displayed very similar binding energies, giving Re4f7/2 signals at 45.1 and 45.0 eV, respectively (Supplementary Fig. 21), which are lower than those in Re@PQA-Py-Cl (45.6 eV) and KReO4 (46.1 eV). This presumably arises from the electron donating groups present in PQA-pNH2Py-Cl and PQA-pN(Me)2Py-Cl, which weakens the partial positive charge on the cations and thereby that on the rhenium species. These observations were further corroborated by the IR spectra (Supplementary Fig. 22), a slight red-shift of the ReO4 antisymmetric vibration was detected in Re@PQA-pNH2Py-Cl and Re@PQA-pN(Me)2Py-Cl (893.8 cm-1) compared to that in Re@PQA-Py-Cl (901.6 cm-1) and KReO4 samples (906.8 cm−1). Regarding electronic factors, the introduction of electron donating groups facilitates the formation of kinetically labile complexes, which allows for rapid guest exchange. However, the relevant explanations cannot correlate with the observed trend, wherein the introduction of the amino group gave adverse results, with the lowest performance of the three materials. To explain this, we reasoned that, different from the dimethylamino group, the amino group acts both as a hydrogen bond donor and a hydrogen bond acceptor. Anions, such as Cl, are inclined to interact with it via hydrogen bonding, thereby compromising the ion-exchange capability for ReO4 ions. Such an interaction between the amino group and the Cl ion is expected considering the successful Cl extraction solely on an amine-based neutral anion receptor27.

Density functional theory calculation studies

We carried out quantum density functional theory (DFT) computations to understand the chemical basis of the binding selectivities toward ReO4/TcO4. Calculations on the truncated fragments shown in Fig. 4 were performed using M06 exchange and correlation functions with fine grid spacing as implemented in NWChem. A 6-311 + + G(2d,2p) basis was used for all atoms except technetium, which was treated with the def2-tzvp basis and associated empirical core potential. This combination of functional and basis set was shown to reproduce experimental geometries of TcO452,53, providing more confidence in the results than could have been obtained with calculations on ReO4. Full details of the quantum mechanical calculation are provided in the Supplementary Information.

Fig. 4
figure4

Electrostatic potential surface. Distribution of the charge density around the aromatic ring is shown by a plot of the electrostatic potential surface just below the molecule. The most favorable binding geometry for a triangular face of an anion has opposite orientations between the cationic building blocks of a PQA-Py-Cl, b, c PQA-pNH2Py-Cl, and d PQA-pN(Me)2Py-Cl. Methyl groups have been introduced to take the electrostatic effects of the polymer chain into account. Comparison of b and c shows some negative charge is donated to the ring system during formation of a hydrogen bond

In all molecules, the pyridinium nitrogen forms a center of positive potential. Concentration of the positive charges at meta-positions would suggest that the triangular faces of NO3, HSO4, and TcO4 should orient directly overtop (Supplementary Fig. 23). Instead, the minimum energy geometries of a show that two of the anion oxygens seek to overlap with the lobes of positive potential on either side of the ring nitrogen closer to its attached methyl. These differences in geometry are significant, since all geometry optimizations started from anion positions containing an oxygen pointing toward the ring nitrogen. For d, the tertiary amine also has a large positive partial charge, and pulls anion oxygens toward itself. The resulting competition between these sites results in the smaller nitrate and sulfate anions stretching one oxygen toward each site, and not effectively using their third binding oxygen. In contrast, the longer bond length of TcO4 allows it to simultaneously occupy positions next to the dimethylamino group and close to the ring nitrogen. This explains the opposite binding orientation to what would be expected based on placing oxygens over both meta- sites. b is interesting and in its place, we see a strong positive charge at the para- location with nearly zero charges meta- to the ring nitrogen. Structure c was included to understand the effect of electron donation to the ring system due to a hydrogen bonding of water to the side-chain amine. It can be seen that the overall potential of the binding site decreases slightly, which will result in less favorable anion binding.

Binding free energies were computed for Cl, TcO4, NO3, and HSO4 to all four structures in Fig. 4 using the quasi-chemical method (see details in Computational Methods Section and Supplementary Table 4 and Fig. 23). The anion HSO4 was used in place of SO42− because the computational results are more reliable when comparing ions of equal valence. The difference in binding free energies between HSO4 and SO42− is the same as the difference between the pKas of HSO4 in bulk solution compared to HSO4 bound to the polymer.

A large portion of the binding free energies is due to solvation effects. These increase polymer binding affinity of the larger (less hydrophilic) TcO4 over the smaller Cl and NO3. Although our solvation free energy calculations were carried out for liquid water, the polymer environment is expected to be slightly more hydrophobic. This will give TcO4 and additional boost relative to other ions that is not reflected in our final calculated selectivities. Entropic effects also contribute additional uncertainty to the calculations because it is difficult to predict the change in volume or rigidity of the surrounding polymer environment upon ion binding. Because of this, our free energy computations include only ligand translational and rotational entropy contributions (treating both binding partners as rigid bodies). Relative to Cl (which has no rotational entropy), the entropy contributions decrease the overall affinity for all ions by 2.5–6 kcalmol-1 (Supplementary Table 4).

The chemical portion of the binding free energies is provided by energy differences in minimum energy configurations. The energy difference itself favors binding of NO3 and HSO4 over TcO4 by 7, 5, and 4 kcalmol-1 for a, b, and d, respectively. This is not surprising, given that partial charges on NO3 are most negative, followed by HSO4 over TcO4 in that order. When energetic and free energy differences are added together, Cl is still the most favored binding partner in gas phase. However, the relatively hydrophobic environment of the polymer combined with the stronger affinity of water for Cl results in the opposite trend of binding free energies in solution. Just as seen in experiments, the final order of ion exchange affinity in solution is TcO4 > HSO4 > NO3 > Cl for all polymers. d has the strongest relative affinity for TcO4, at -6.1 kcal mol−1 relative to Cl, while its affinity for HSO4 is -3.9 and for NO3 is −3.8 kcalmol−1, which is in accordance with our experiment results (Supplementary Table 4).

Stability test

Considering the superior performance of PQA-pN(Me)2Py-Cl to extract ReO4 with good affinity and selectivity in the aforementioned situations, it was therefore the sample of choice for more detailed studies. The ability to regenerate and recycle the material would afford great advantages in reducing the overall cost and hence facilitating practical applications. To this end, the possibility of regeneration and reusing of PQA-pN(Me)2Py-Cl were evaluated. Significantly, the ion exchange processes were fully reversible as reflected by the fact that the loaded ReO4 ions can be washed off by saturated NaCl aqueous solutions with maintained ion-exchange capacity for at least three cycles, affording 990, 1003, and 987 mg g−1, respectively (Fig. 5a). These results suggest the adequate chemical and structural stability of PQA-pN(Me)2Py-Cl, which was further established by the following experiments. The ReO4 uptake capacities and the pore structure of PQA-pN(Me)2Py-Cl remained almost unchanged after being soaked in 12 M HCl or 2 M NaOH in saturated NaCl aqueous solution for one week (Fig. 5b and Supplementary Fig. 24). More impressively, PQA-pN(Me)2Py-Cl was able to maintain its performance in extraction of ReO4 from 3 M HNO3 solution for more than three times with approximately 70% of ReO4 from the HNO3 solution containing 1.6 mM of ReO4 (NO3: ReO4 molar ratio = 1875) at a phase ratio of 50 mLg−1 after a single treatment (Fig. 5c). Notably, a removal efficiency of 97% can be reached at a phase ratio of 20 mLg−1 (a number that is nearly half that used for the chromatographic column application, 11 mLg−1). These features clearly represent a priority in uptake for ReO4/TcO4 over NO3, thereby showing its potential for removing TcO4 from reprocessed used fuel prior to the plutonium uranium redox extraction (PUREX) process.

Fig. 5
figure5

Stability evaluation. a Reversibility of PQA-pN(Me)2Py-Cl for removing ReO4-. b ReO4- uptake capacities of PQA-pN(Me)2Py-Cl after being soaked in 12 M HCl or 2 M NaOH in saturated NaCl aqueous solution for one week. c Removal of ReO4- by PQA-pN(Me)2Py-Cl as a function of phase ratio (V/m) in 3 M HNO3 aqueous solution. d Sorption capacities of ReO4 by PQA-pN(Me)2Py-Cl after being irradiated with varied doses of β-rays or γ-rays. Source data are provided as a Source Data file

Given that the above studies were done with non-radioactive elements, how radiation interacts with the materials was not taken into account54. Therefore, to rationalize results obtained from simulants, external radiation sources were exerted. Very impressively, PQA-pN(Me)2Py-Cl exhibits outstanding resistance toward high-energy ionizing radiation of both β- and γ-rays, indicative by no noticeable change in the IR spectra, morphology, surface areas, ae well as the sorption performance measurements on the irradiated samples in relation to the pristine material, thereby providing a substantial prerequisite for application in used nuclear fuel reprocessing and waste management (Supplementary Figs. 2527). Remarkably, even after irradiation with extremely large doses of 1000 kGy of β- or γ-rays, the sorption rate and capacity for ReO4 by PQA-pN(Me)2Py-Cl remained unaffected (Fig. 5d). PQA-pN(Me)2Py-Cl combines the attributes of high capacity, reusability, and resistance against radiation, providing an extended lifetime that is sought after for long-term use in nuclear waste water treatment applications.

Removal from simulated nuclear wastes

To further validate the results, TcO4 uptake experiments were performed by contacting PQA-pN(Me)2Py-Cl with an aqueous solution of TcO4. The concentration of TcO4 was monitored by liquid scintillation counting measurements. As shown in Supplementary Fig. 28, PQA-pN(Me)2Py-Cl was kinetically favored, 99% of TcO4 could be removed within 5 min

With this success, it promoted us to investigate performance of PQA-pN(Me)2Py-Cl in legacy nuclear waste. Previous estimates of Hanford tank waste inventories indicated that the amount of technetium in the waste needed to be reduced substantially to prepare immobilized low activity waste (ILAW) glass that meets performance assessment requirements. To investigate the removal of TcO4 for this application, we prepared a simulated Hanford LAW melter recycle stream, where the amounts of NO3, NO2, and Cl are more than 300 times that of TcO4, as listed in Supplementary Table 5, resulting in an enormous challenge to selectively remove TcO4. Following similar experimental conditions as the established procedures (see details in the Supplementary Information), PQA-pN(Me)2Py-Cl was found to remove about 95% of available TcO4 from the waste at a phase ratio of 200 mL g-1, placing it within striking distance of the all-time TcO4 removal record (Supplementary Table 6). To further extend the potential application of PQA-pN(Me)2Py-Cl in nuclear waste remediation, we tested its capability for the decontamination of TcO4 in Savannah River Sites. It was shown to be effective for the segregation of TcO4 from simplified simulants, a strong basic TcO4 solution with the strength of other anions over 70 000 times that of TcO4 (Supplementary Table 7). Approximately 80% of available TcO4 was extracted from the waste at a phase ratio of 100 mL g-1, which to date, we have found no materials in the literature with comparable selectivity under similar conditions. Although applicable to pertechnetate-containing waste streams in general, these two examples discussed here were directed at two specific potential applications at the U.S. Department of Energy’s legacy site: i) the removal of dilute pertechnetate from near-neutral solutions, typical of the eluent streams from pretreated Hanford tank wastes, and ii) the direct removal of pertechnetate from highly alkaline solutions, typical of those found in Savannah River Sites.

Discussion

In summary, based on the results above, we can now formulate clear design rules to achieve ideal ReO4/TcO4 scavengers with optimal uptake capacity and selectivity. The presented case shows that a subtle interplay between various functions in the adsorbent-in this case incorporation of a distinct functionality on a cation moiety-would be used to obtain an optimally performing adsorbent. Given the fact that ion exchange often follows a similar mechanism, we expect that the trends discovered here will also be of high relevance for many other sequestration processes, such as coordinative binding. We conceptually showed the potential for tuning binding sites in selective capture to a greater degree of complexity. Given the demonstrated easy tunability, regeneration, and separation combined with radioactive resistance, long-term stability, and high performance in application relevant conditions, these new materials presented here could become highly influential for nuclear wastewater treatment technologies, particularly in the event of an impending water crisis. Also, potential cost savings and schedule acceleration could be anticipated based on consequent improvements in vitrification processing, reduction in waste form volumes, and higher waste-package performance.

Methods

Materials and measurements

Commercially available reagents were purchased in high purity and used without purification. The purity and structure of the compounds synthesized in this manuscript were determined by NMR technique (Supplementary Fig. 29). Nitrogen sorption isotherms at the temperature of liquid nitrogen were measured using Micromeritics ASAP 2020M and Tristar system. 1H NMR spectra were recorded on a Bruker Avance-400 (400 MHz) spectrometer. Chemical shifts are expressed in ppm downfield from TMS at δ = 0 ppm, and J values are given in Hz. 13C (100.5 MHz) cross-polarization magic-angle spinning (CP-MAS) NMR experiments were recorded on a Varian infinity plus 400 spectrometer equipped with a magic-angle spin probe in a 4-mm ZrO2 rotor. The samples were outgassed for 1000 min at 80 °C before the measurements. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) mapping were performed on a Hitachi SU 8000. Transmission electron microscope (TEM) image was performed using a Hitachi HT-7700 or JEM-2100F field emission electron microscope (JEOL, Japan) with an acceleration voltage of 110 kV. High-angle-annular-dark-field (HAADF) scanning, STEM imaging, and energy dispersive X-ray spectroscopy (EDX) mapping were carried out by Titan ChemiSTEM operated at 200 kV. XPS spectra were performed on a Thermo ESCALAB 250 with Al Kα irradiation at θ = 90° for X-ray sources, and the binding energies were calibrated using the C1s peak at 284.9 eV. IR spectra were recorded on a Nicolet Impact 410 FTIR spectrometer. The concentrations of TcO4 in solution were measured using a UV–vis spectrometer (Varian Cary 6000i) by monitoring the characteristic absorption peak at 290 nm and the activity of 99TcO4 was also analyzed by a liquid scintillation counting (LSC) system (Perkin Elmer Quantulus 1220). ICP-OES was performed on a Perkin-Elmer Elan DRC II Quadrupole. ICP-MS was performed on a Perkin-Elmer Elan DRC II Quadrupole Inductively Coupled Plasma Mass Spectrometer. Elemental analyses were performed via flask combustion followed by ion chromatography.

Data availability

The authors declare that all the data supporting the findings of this study are available within the article (and Supplementary Information files), or available from the corresponding author on reasonable request. The source data underlying Figs. 2, 3, and 5 are provided as a Source Data file.

References

  1. 1.

    Dresselhaus, M. S. & Thomas, I. L. Alternative energy technologies. Nature 414, 332–337 (2001).

    ADS  CAS  Article  Google Scholar 

  2. 2.

    Sun, Q., Aguila, B. & Ma, S. Opportunities of Porous Organic Polymers for Radionuclide Sequestration. Trends in Chemistry 1, https://doi.org/10.1016/j.trechm.2019.02.010 (2019).

  3. 3.

    Abney, C. W., Mayes, R. T., Saito, T. & Dai, S. Materials for the recovery of uranium from seawater. Chem. Rev. 117, 13935–14013 (2017).

    CAS  Article  Google Scholar 

  4. 4.

    Yue, Y. et al. Seawater uranium sorbents: preparation from a mesoporous copolymer initiator by atom-transfer radical polymerization. Angew. Chem. Int. Ed. 52, 13458–13462 (2013).

    CAS  Article  Google Scholar 

  5. 5.

    Yuan, Y. et al. Molecularly imprinted porous aromatic frameworks and their composite components for selective extraction of uranium ions. Adv. Mater. 30, 1706507 (2018).

    Article  Google Scholar 

  6. 6.

    Sun, Q. et al. Covalent organic frameworks as a decorating platform for utilization and affinity enhancement of chelating sites for radionuclide sequestration. Adv. Mater. 30, 1705479 (2018).

    Article  Google Scholar 

  7. 7.

    Taylor, R. Reaction: a role for actinide chemists. Chemistry 1, 659–665 (2016).

    Article  Google Scholar 

  8. 8.

    zur Loye, H.-C. et al. Hierarchical materials as tailored nuclear waste forms: a perspective. Chem. Mater. 30, 4475–4488 (2018).

    CAS  Article  Google Scholar 

  9. 9.

    Abney, C. W. et al. Topotactic transformations of metal-organic frameworks to highly porous and stable inorganic sorbents for efficient radionuclide sequestration. Chem. Mater. 26, 5231–5243 (2014).

    CAS  Article  Google Scholar 

  10. 10.

    Harvey, P., Nonat, A., Platas-Iglesias, C., Natrajan, L. S. & Charbonnière, L. J. Sensing uranyl(VI) ions by coordination and energy transfer to a luminescent europium(III) complex. Angew. Chem. Int. Ed. 57, 9921–9924 (2018).

    CAS  Article  Google Scholar 

  11. 11.

    Seliman, A. F., Samadi, A., Husson, S. M., Borai, E. H. & DeVol, T. A. Preparation of polymer-coated, scintillating ion-exchange resins for monitoring of 99Tc in groundwater. Anal. Chem. 83, 4759–4766 (2011).

    CAS  Article  Google Scholar 

  12. 12.

    Amendola, V., Bergamaschi, G., Boiocchi, M., Alberto, R. & Braband, H. Fluorescent sensing of 99Tc pertechnetate in water. Chem. Sci. 5, 1820–1826 (2018).

    Article  Google Scholar 

  13. 13.

    Del Cul, G. D., Bostick, W. D., Trotter, D. R. & Osboren, P. E. Technetium-99 removal from process solutions and contaminated groundwater. Sep. Sci. Technol. 28, 551–564 (1993).

    Article  Google Scholar 

  14. 14.

    Darab, J. G. et al. Removal of pertechnetate from simulated nuclear waste streams using supported zero valent iron. Chem. Mater. 19, 5703–5713 (2007).

    CAS  Article  Google Scholar 

  15. 15.

    Lee, M.-S. et al. Impeding 99Tc(IV) mobility in novel waste forms. Nat. Commun. 7, 12067 (2016).

    ADS  CAS  Article  Google Scholar 

  16. 16.

    Drout, R. J. et al. Efficient capture of perrhenate and pertechnetate by a mesoporous Zr metal-organic framework and examination of anion binding motifs. Chem. Mater. 30, 1277–1284 (2018).

    CAS  Article  Google Scholar 

  17. 17.

    Banerjee, D., Kim, D., Schweiger, M. J., Kruger, A. A. & Thallapally, P. K. Removal of TcO4 ions from solution: materials and future outlook. Chem. Soc. Rev. 45, 2724–2739 (2016).

    CAS  Article  Google Scholar 

  18. 18.

    Li, J. et al. Metal-organic framework-based materials: superior adsorbents for the capture of toxic and radioactive metal ions. Chem. Soc. Rev. 47, 2322–2356 (2018).

    CAS  Article  Google Scholar 

  19. 19.

    Li, B. et al. Creation of a new type of ion exchange material for rapid, high-capacity, reversible and selective ion exchange without swelling and entrainment. Chem. Sci. 7, 2138–2144 (2016).

    CAS  Article  Google Scholar 

  20. 20.

    Wang, S. et al. NDTB-1: A supertetrahedral cationic framework that removes TcO4 from solution. Angew. Chem. Int. Ed. 49, 1057–1060 (2010).

    CAS  Article  Google Scholar 

  21. 21.

    Wang, S. et al. Selectivity, kinetics, and efficiency of reversible anion exchange with TcO4 in a supertetrahedral cationic framework. Adv. Funct. Mater. 22, 2241–2250 (2012).

    CAS  Article  Google Scholar 

  22. 22.

    Sheng, D. et al. Efficient and selective uptake of TcO4 by a cationic metal-organic framework material with open Ag+ sites. Environ. Sci. Technol. 51, 3471–3479 (2017).

    ADS  CAS  Article  Google Scholar 

  23. 23.

    Zhu, L. et al. Identifying the recognition site for selective trapping of 99TcO4 in a hydrolytically stable and radiation resistant cationic metal-organic framework. J. Am. Chem. Soc. 139, 14873–14876 (2017).

    CAS  Article  Google Scholar 

  24. 24.

    Li, J. et al. 99TcO4 remediation by a cationic polymeric network. Nat. Commun. 9, 3007 (2018).

    ADS  Article  Google Scholar 

  25. 25.

    Zhang, D., Ronson, T. K., Mosquera, J., Martinez, A. & Nitschke, J. R. Selective anion extraction and recovery using a FeII 4L4 cage. Angew. Chem. Int. Ed. 57, 3717–3721 (2018).

    CAS  Article  Google Scholar 

  26. 26.

    He, Q. et al. Angew. Chem. Int. Ed. 57, 11924–11928 (2018).

    CAS  Article  Google Scholar 

  27. 27.

    Schmidtchen, F. P. & Berger, M. Artificial organic host molecules for anions. Chem. Rev. 97, 1609–1646 (1997).

    CAS  Article  Google Scholar 

  28. 28.

    Ji, X. et al. Physical removal of anions from aqueous media by means of a macrocycle-containing polymeric network. J. Am. Chem. Soc. 140, 2777–2780 (2018).

    CAS  Article  Google Scholar 

  29. 29.

    Huang, N., Zhai, L., Xu, H. & Jiang, D. Stable covalent organic frameworks for exceptional mercury removal from aqueous solutions. J. Am. Chem. Soc. 139, 2428–2434 (2017).

    CAS  Article  Google Scholar 

  30. 30.

    Ding, S.-Y. et al. Thioether-based fluorescent covalent organic framework for selective detection and facile removal of mercury(II). J. Am. Chem. Soc. 138, 3031–3037 (2016).

    CAS  Article  Google Scholar 

  31. 31.

    Li, Z. et al. Three-dimensional ionic covalent organic frameworks for rapid, reversible, and selective ion exchange. J. Am. Chem. Soc. 139, 17771–17774 (2017).

    CAS  Article  Google Scholar 

  32. 32.

    Alsbaiee, A. et al. Rapid removal of organic micropollutants from water by a porous β-cyclodextrin polymer. Nature 529, 190–194 (2016).

    ADS  CAS  Article  Google Scholar 

  33. 33.

    Sun, D. T. et al. Rapid, selective heavy metal removal from water by a metal-organic framework/polydopamine composite. ACS Cent. Sci. 4, 349–356 (2018).

    CAS  Article  Google Scholar 

  34. 34.

    Alvarez, P. J., Chan, C. K., Elimelech, M., Halas, N. J. & Villagrán, D. Emerging opportunities for nanotechnology to enhance water security. Nat. Nanotechnol. 13, 634–641 (2018).

    ADS  CAS  Article  Google Scholar 

  35. 35.

    Slater, A. G. & Cooper, A. I. Function-led design of new porous materials. Science 348, aaa988 (2015).

    Article  Google Scholar 

  36. 36.

    Das, S., Heasman, P., Ben, T. & Qiu, S. Porous organic materials: strategic design and structure-function correlation. Chem. Rev. 117, 1515–1563 (2017).

    CAS  Article  Google Scholar 

  37. 37.

    Xu, Y., Jin, S., Xu, H., Nagai, A. & Jiang, D. Conjugated microporous polymers: design, synthesis and application. Chem. Soc. Rev. 42, 8012–8031 (2013).

    CAS  Article  Google Scholar 

  38. 38.

    Wu, D., Xu, F., Sun, B., Fu, R., He, H. & Matyjaszewski, K. Design and preparation of porous polymers. Chem. Rev. 112, 3959–4015 (2012).

  39. 39.

    Ben, T. et al. Gas storage in porous aromatic frameworks (PAFs). Energy Environ. Sci. 4, 3991–3999 (2011).

    CAS  Article  Google Scholar 

  40. 40.

    Yan, Z., Yuan, Y., Tian, Y., Zhang, D. & Zhu, G. Highly efficient enrichment of volatile iodine by charged porous aromatic frameworks with three sorption sites. Angew. Chem. Int. Ed. 54, 12733–12737 (2015).

    CAS  Article  Google Scholar 

  41. 41.

    Wang, P. et al. Exceptional iodine capture in 2D covalent organic frameworks. Adv. Mater. 30, 1801991 (2018).

    Article  Google Scholar 

  42. 42.

    Li, B., Zhang, Y., Ma, D., Shi, Z. & Ma, S. Mercury nano-trap for effective and efficient removal of mercury (II) from aqueous solution. Nat. Commun. 5, 5537 (2014).

    ADS  CAS  Article  Google Scholar 

  43. 43.

    Byun, J., Patel, H. A., Thirion, D. & Yavuz, C. T. Charge-specific size-dependent separation of water-soluble organic molecules by fluorinated nanoporous networks. Nat. Commun. 7, 13377 (2016).

    ADS  CAS  Article  Google Scholar 

  44. 44.

    Sun, Q. et al. Bio-inspired nano-traps for uranium extraction from seawater and recovery from nuclear waste. Nat. Commun. 9, 1644 (2018).

    ADS  Article  Google Scholar 

  45. 45.

    Sun, X., Luo, H. & Dai, S. Ionic liquids-based extraction: a promising strategy for the advanced nuclear fuel cycle. Chem. Rev. 112, 2100–2128 (2012).

    CAS  Article  Google Scholar 

  46. 46.

    Bonnesen, P. V. et al. Development of bifunctional anion-exchange resins with improved selectivity and sorptive kinetics for pertechnetate: batch-equilibrium experiments. Environ. Sci. Technol. 34, 3761–3766 (2000).

    ADS  CAS  Article  Google Scholar 

  47. 47.

    Sun, Q. et al. Superhydrophobicity: constructing homogeneous catalysts into superhydrophobic porous frameworks to protect them from hydrolytic degradation. Chem 1, 628–639 (2016).

    CAS  Article  Google Scholar 

  48. 48.

    Sun, Q. et al. Highly efficient heterogeneous hydroformylation over Rh-metalated porous organic polymers: synergistic effect of high ligand concentration and flexible framework. J. Am. Chem. Soc. 137, 5204–5209 (2015).

    CAS  Article  Google Scholar 

  49. 49.

    Sun, Q., Ma, S., Dai, Z., Meng, X. & Xiao, F.-S. A hierarchical porous ionic organic polymer as a new platform for heterogeneous phase transfer catalysis. J. Mater. Chem. A 47, 23871–23875 (2015).

    Article  Google Scholar 

  50. 50.

    Darab, J. G. & Smith, P. A. Chemistry of technetium and rhenium species during low-level radioactive waste vitrification. Chem. Mater. 8, 1004–1021 (1996).

    CAS  Article  Google Scholar 

  51. 51.

    Santhosh, C. et al. Role of nanomaterials in water treatment applications: A review. Chem. Eng. J. 306, 1116–1137 (2016).

    CAS  Article  Google Scholar 

  52. 52.

    Williams, C. D., Burton, N. A., Travis, K. P. & Harding, J. H. The development of a classical force field to determine the selectivity of an aqueous Fe3+-EDA complex for TcO4 and SO4 2–. J. Chem. Theory. Comput. 10, 3345–3353 (2014).

    CAS  Article  Google Scholar 

  53. 53.

    Weaver, J. et al. Chemical trends in solid alkali pertechnetates. Inorg. Chem. 56, 2533–2544 (2017).

    CAS  Article  Google Scholar 

  54. 54.

    Pillay, K. K. S. A review of the radiation stability of ion exchange materials. J. Radioanal. Nucl. Chem. 102, 247–268 (1986).

    CAS  Article  Google Scholar 

Download references

Acknowledgements

We acknowledge the US National Science Foundation (CBET-1706025) and the University of South Florida for financial support of this work.

Author information

Affiliations

Authors

Contributions

Q.S. and S.M. conceived and designed the research. Q.S. and B.A. performed the synthesis. Q.S., L.Z., P.K.T., and B.A. carried out the adsorption tests. C.X., J.C., and S.W. conducted the radiation stability tests. D. R. contributed to DFT calculation. All authors participated in drafting the paper, and gave approval to the final version of the manuscript.

Corresponding authors

Correspondence to Shuao Wang or Shengqian Ma.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Journal peer review information: Nature Communications thanks Masashi Kaneko and the other anonymous reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Sun, Q., Zhu, L., Aguila, B. et al. Optimizing radionuclide sequestration in anion nanotraps with record pertechnetate sorption. Nat Commun 10, 1646 (2019). https://doi.org/10.1038/s41467-019-09630-y

Download citation

Further reading

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Search

Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing