Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Mid infrared gas spectroscopy using efficient fiber laser driven photonic chip-based supercontinuum


Directly accessing the middle infrared, the molecular functional group spectral region, via supercontinuum generation processes based on turn-key fiber lasers offers the undeniable advantage of simplicity and robustness. Recently, the assessment of the coherence of the mid-IR dispersive wave in silicon nitride (Si3N4) waveguides, pumped at telecom wavelength, established an important first step towards mid-IR frequency comb generation based on such compact systems. Yet, the spectral reach and efficiency still fall short for practical implementation. Here, we experimentally demonstrate that large cross-section Si3N4 waveguides pumped with 2 μm fs-fiber laser can reach the important spectroscopic spectral region in the 3–4 μm range, with up to 35% power conversion and milliwatt-level output powers. As a proof of principle, we use this source for detection of C2H2 by absorption spectroscopy. Such result makes these sources suitable candidate for compact, chip-integrated spectroscopic and sensing applications.


The middle infrared (mid-IR) spectral region (2–10 μm) has a high technological importance for spectroscopy and sensing with applications in health and environmental monitoring1,2. Particularly, the 3–5 μm region, the functional group region, is interesting as it hosts the first mid-IR atmospheric window, and contains the molecular fingerprint of many hydrocarbons, nitrogen dioxide, greenhouse gases, and specimens detectable in breath analysis3. Besides direct mid-IR generation with quantum cascade lasers4, interband cascade lasers5, and Fe2+ doped crystals6, wavelength conversion in nonlinear materials is a promising solution to reach the mid-IR spectral range. Very efficient conversion towards mid-IR has been demonstrated through frequency-divide-by-two optical parametric oscillators7,8 and difference frequency generation (DFG) between two telecom band signals9,10,11,12,13.

Broadband mid-IR generation can also be achieved by supercontinuum generation (SCG) in soft glass optical fibers14,15,16,17,18,19,20,21,22,23 or photonic integrated waveguides24,25,26,27,28,29,30,31. Compared to other wavelength conversion schemes, SCG offers some advantages32: it is in fact a compact single-pass geometry that does not require any additional seed laser or temporal synchronization, and it can provide a broader and tunable mid-IR emission. When CMOS compatible materials are employed, SCG platforms benefit from lithographic precision and high yield, and usually have low power consumption. Recent works have shown that such approach can be applied as well to dual-comb spectroscopy32.

Often, to extend the reach into the mid-IR, the nonlinear waveguides are pumped with an optical parametric oscillator placed beyond the 2-micron wavelength range, but there is interest in driving such platforms with femtosecond mode-locked fiber lasers, which are reliable, easy to use, and compact frequency comb sources.

However, up to now, very few demonstrations succeeded in generating supercontinua following this paradigm. High energy (2–3 nJ) femtosecond pulses in the 2-micron region can lead to more than 30% of conversion efficiency (CE) beyond 2200 nm in an InF3 fiber22, and spectral broadening extending beyond 4.5 μm in Telluride photonic crystal fibers23. Despite the large CE and spectral extent, the coherence of such mid-IR emission has not been experimentally investigated. Conversely, low pulse energy (18 pJ) at 2000 nm can lead to coherent mid-IR SCG in chalcogenides nanospikes16,17 or nanotapers19, but early damage power threshold and high mid-IR absorption from the cladding avoid power scaling up to the milliwatt level. In terms of chip integrated waveguides, mid-IR extended SCG has been experimentally demonstrated in AlN waveguides pumped with 0.8 nJ from a telecom band femtosecond mode-locked fiber laser24. The power generated inside the waveguide in the 3000–4000 nm range is about 0.3 mW, corresponding to a CE close to 0.5%. Overall, none of the above-mentioned approaches has been employed for mid-IR spectroscopy demonstrations.

Also, in the last years there has been a trend in miniaturizing and simplifying DFG schemes by utilizing single pump configuration with chip-scale nonlinear platforms. Emission up to 5.5 μm was obtained by DFG between the pump and the long-wavelength dispersive wave (DW) in AlN waveguides24, while intrapulse DFG, generated from an Er:doped fiber mode-locked laser, enables tunable mid-IR radiation in the 4–5 μm region using PPLN waveguides33. However, efficiencies are limited to below 0.5%.

Recently, we showed that direct generation of mid-IR light, from an erbium-doped fiber laser at 1.56 μm, is possible through DW generated in Si3N4, and asserted the phase coherence and frequency comb nature34. This platform has the potential to merge all the desired features addressed separately in the above-mentioned devices: a power scalable, fiber laser pumped coherent mid-IR generation in a low loss chip-scale waveguide with lithographical control of its dispersion.

However, the outstanding problem in this first demonstration was the extremely low CE and insufficient power beyond 3 μm for future molecular fingerprinting. Indeed, reaching efficient DW generation beyond 3 μm is still difficult in CMOS platforms directly pumped by fiber lasers. The larger is the spectral coverage, the lower is the power transferred in the targeted region. Moreover, the SCG process can convert a non-negligible portion of the pump energy over unwanted spectral bands, such as in the visible, further decreasing the CE in the region of interest35.

In this work, we overcome these hurdles and demonstrate a turn-key, high-efficient, and compact mid-IR source based on DW generation with power levels sufficient for spectroscopy application. We leverage both recent advances in fiber laser technologies, which allow shifting their emission wavelength in the short wave infrared (SWIR), until the limit of the silica absorption edge (around 2.1 μm), and large cross-section waveguide designs36, enabling considerable freedom in dispersion engineering and low mid-IR propagation losses. In this way we efficiently convert, to the 3–4 μm wavelength region, a commercial SWIR femtosecond fiber laser by setting the pump wavelength as to favor dispersion for targeted long wavelength operation. Record CE, defined as on-chip generated mid-IR DW power over on-chip coupled pump laser power, as high as 35% is reached at 3.05 μm, and close to 20% at 3.950 μm, corresponding to more than one milliwatt average power at the chip output. A systematic experimental and numerical study on the generation of mid-IR DW provides new information on the efficiency and dynamics of the DW generation process as a function of the pump power. Finally, as a proof-of-principle, we successfully exploit this on-chip mid-IR source for C2H2 detection through gas absorption spectroscopy.


Design of mid-IR source through dispersive wave optimization

It is well known that propagation of sufficiently powerful femtosecond laser pulses in the anomalous group velocity dispersion (GVD) region of a nonlinear waveguide can induce high order soliton dynamics35, leading to an initial spectral broadening caused by self-phase modulation (SPM) and subsequent temporal compression which are proportional to the soliton number37. At the compression point, when the spectrum is extensively broadened, the soliton can be perturbed by high order dispersion (HOD) or nonlinear terms resulting in soliton fission, and can transfer energy to linear DW spectrally shifted from the pump35. The DW generation process can occur at the frequency where the phase constant of the soliton pulse equals the one of the linear wave38, and is thus given by the phase matching condition:

$$\beta \left( \omega \right) - \beta \left( {\omega _s} \right) - v_g^{ - 1}\left( {\omega - \omega _s} \right) = \frac{{\gamma P}}{2}$$

where β is the mode propagation vector, ωs is the soliton central frequency, vg is the soliton group velocity, P is the pulse peak power, and γ is the waveguide’s effective nonlinearity. The nonlinear phase shift on the right-hand side of Eq. (1) is small and is usually neglected. The left-hand side of Eq. (1) is called integrated dispersion βint, and can be rewritten as a Taylor expansion leading to

$$\beta _{{\mathop{\rm{int}}} } = \mathop {\sum}\limits_{k \ge 2} {\frac{{\left( {\omega - \omega _s} \right)^k}}{{k!}}} \left. {\frac{{\partial ^k\beta }}{{\partial \omega ^k}}} \right|_{\omega = \omega _s} \approx 0$$

The GVD determines the location of the phase matching points and it has been shown that the generation of a phase matched DW corresponds to the occurrence of a zero dispersion wavelength (ZDW)39,40. Also, HOD terms (k > 2) affect the amount of power transfer to the DW38,40,41. Qualitatively, even-order dispersion terms lead to two DWs with symmetric intensity and frequency detuning42 with respect to the pump, while positive or negative odd-order terms break this symmetry favoring blue or red-shifted DW, respectively40. The material dispersion of Si3N4 can easily lead to a first ZDW point in the near-IR for the fundamental waveguide mode, responsible for DW generation at visible wavelengths. The large anomalous material GVD in the mid-IR has to be compensated by waveguide dispersion in order to reach a second ZDW at longer wavelengths. However, efficiently converting the light to the mid-IR DW means that conversion towards the unwanted visible DW has to be limited, and mid-IR mode confinement has to be improved to avoid cladding absorption. These limitations can be mitigated, as seen in Fig. 1, by combining large cross-section waveguides, which satisfy both the necessary confinement and dispersion engineering, with accurate positioning of the pump wavelength, to meet the requirements on HOD terms. The waveguides we use in this study have a height that can reach 2.2 μm, with width in the 1 μm range, while the central wavelength of the pump laser can be tuned between 2070 and 2090 nm.

Fig. 1

Comparison between standard and large cross-section silicon nitride (Si3N4) waveguides. a Group velocity dispersion (GVD) for the TE fundamental mode of a standard waveguide with cross-section 870 × 1700 nm2 (blue) and the TM fundamental mode of a large cross-section waveguide with dimension 2177 × 1150 nm2 (red). The insets show scanning electron microscope (SEM) images of the waveguide cross-section. b Attenuation coefficient α as a function of wavelength for (blue) standard and (red) large cross-section waveguides. c Solid lines: integrated dispersion as a function of the wavelength for the standard waveguide pumped at 1560 nm (blue) and the large cross-section one pumped at 2090 nm (red). The dispersive wave (DW) phase matching points lie in the same region for both configurations. Dashed red line: integrated dispersion as a function of the wavelength for the large cross-section waveguide pumped at 1560 nm. Pump positions are indicated by the arrows

In Fig. 1a, we show the computed GVD of standard (with a height around 870 nm) and large cross-section Si3N4 waveguides. The second ZDW of the latter waveguides is further red-shifted compared to standard ones, enabling the generation of DW deeper in the mid-IR for the same pump wavelength. At the same time, the large cross-section waveguide can significantly reduce mid-IR absorption in the silica cladding through improved mode confinement, as seen in Fig. 1b, where we computed the absorption losses α by including the imaginary part of the refractive index of silica in our numerical simulations (see Methods). The amount of integrated dispersion separating the pump from the DW phase matched wavelengths, which we will refer to as dispersion barrier, clearly illustrates a symmetry breaking in DW generation. As seen in Fig. 1c, a 2090 nm pump in large cross-section waveguides generates a mid-IR DW in the same wavelength range as the one obtained by using standard waveguides with a 1560 nm pump. However, 2090 nm pumping in large waveguides leads to a much lower mid-IR dispersion barrier, and a much higher visible one, that should clearly favor mid-IR power transfer. It has to be noticed that even if the large cross-section waveguide pumped at 1560 nm in theory features a DW generated beyond 5 μm, the mid-IR dispersion barrier will also significantly increase (Fig. 1c), greatly limiting the efficiency.

Experimental implementation and simulated dynamics

The experimental set-up is detailed in Fig. 2a. The pump source is a commercial, turn-key soliton self-frequency shifted thulium-doped fiber mode-locked laser (NOVAE Brevity λ+), with pulse duration at full width half maximum (FWHM) of 78 fs, bandwidth of 60 nm centered at 2090 nm, repetition rate of 19 MHz and average power of about 100 mW. Before coupling to the waveguide, the polarization is managed and the power can be varied with a variable optical attenuator (VOA). Light is coupled into the fundamental transverse magnetic (TM) polarization mode of the waveguide, facilitated by inverse tapers and using two identical aspheric black diamond lenses. At the device output, the collimated light is focused by means of a parabolic mirror onto a fluoride multimode fiber (MMF) and the spectra are recorded with a Fourier Transform Optical Spectrum Analyzer (FT-OSA) spanning the 1–5 μm range (Thorlabs OSA205C). The top view of the device is acquired with a microscope objective which projects the image on a visible camera. The samples consist of 5 mm long straight Si3N4 waveguides buried in SiO2. We investigated waveguides with four different nominal widths: 1000, 1050, 1100, and 1175 nm. The waveguide thickness slightly increases with larger widths, ranging from 2.09 to 2.19 μm. The total coupling losses were around 11 dB for the larger waveguides, but 1.5 and 2.5 dB higher for the 1050 and 1000 nm respectively, while propagation losses are 0.2 dB/cm. Figure 2b shows the experimentally recorded output spectrum from the 1100 nm width waveguide for a coupled average power of 13.6 mW, corresponding to about 6.8 kW peak power and coupled pulse energy of 0.75 nJ. For these values, the soliton number is around 5. A clear DW is observed at the expected phase matching position near 3.5 μm.

Fig. 2

Experimental set-up and dispersive wave generation. a Experimental set-up. HWP half wave plate, QWP quarter wave plate, M mirror, MMF multimode fiber. The left inset is a picture of the chip and input coupling lens, while the right one is an image of the output of the waveguide taken from the top camera. Both images are taken under the same pumping condition. b Experimental (shaded region) and theoretical simulated (solid and dotted lines) input and output spectra for 13.6 mW average power coupled in the 1100 nm width waveguide. Spectral (c) and temporal (d) pump pulse evolution (dB scale) over the waveguide length for an input pulse of 110 fs at 2090 nm, with frequency chirp C = −1000 fs2/2π

Indeed the obtained simulated spectrum reproduces well the experimental one after a propagation of 4.2 mm, which matches the length of the straight waveguide section, without considering the tapered regions. It also shows a weaker visible DW around 500 nm which cannot be detected by the FT-OSA, but justifies the observed green light scattered out of the chip (see Fig. 2a). Looking at the simulated pulse evolution over the waveguide length (Fig. 2c), we notice how both the visible and mid-IR DWs are generated at the soliton compression point which takes place at around lc = 3.5 mm, also qualitatively confirmed on the waveguide image in Fig. 2a. Moreover, Fig. 2c shows how, after the first compression point, additional spectral broadening points separated by a much shorter distance occur. This behavior can be understood by looking at the temporal evolution in Fig. 2d. Just after the first compression point, the propagating pulse separates in two pulses in a process known as the soliton splitting effect43. Due to HOD and high order nonlinear effects (e.g., the self-steepening effect), one of the pulses has more energy and can undergo sufficient broadening to again overlap with the DW. The soliton self-compression process can thus repeat, leading to multiple generation of DW as long as the new pulse maintains enough energy for the necessary spectral broadening. This mechanism thus reinforces the power in the DW spectral region.

Evolution and efficiency of DW generation

The simulated integrated dispersions (Fig. 3a) indicate that the 2090 nm pump significantly favors mid-IR DW for the four waveguide geometries, and that the phase matching point continuously shifts towards longer wavelength with increasing width. This expected behavior is confirmed experimentally as seen in Fig. 3b. We measure a DW peak at 3050, 3220, 3530, and 3950 nm for the 1000, 1050, 1100, and 1175 nm waveguide width, respectively. There is a difference with the theoretically predicted phase matched wavelengths for the smaller waveguides, which can be primarily due to the recoil of the central soliton toward shorter wavelengths and small variation in the actual waveguide dimensions (see Supplementary Note 1). In fact, because of the negligible Raman response39, here we do not see the red-shift of the soliton and the consequent trapping of DW, as observed in silica fibers44,45. The spectra of Fig. 3b also show that, apart from some pump broadening due to SPM, most of the converted pump energy lies in the DW bandwidth. We both experimentally retrieved and numerically simulated the on-chip CE for all tested waveguides (see Methods). It should be noted that the 1000 nm wide waveguide suffered from higher input coupling loss, which limited the range of coupled pump power.

Fig. 3

Dispersive wave generation. a Integrated dispersion for the four waveguides under test. The inset shows expected mid-IR phase matching points. b Experimental spectra recorded at an estimated average coupled power of 13.6 mW, for the four different waveguides under test (same color convention as for (a)). Points show the expected mid-IR phase matching points

The results for the on-chip mid-IR DW CE as a function of the coupled pump power are plotted in Fig. 4a. We observe a power threshold above which the DW is generated. This threshold comes from the fact that the power must be high enough for the soliton compression point to occur before the end of the waveguide since37 lc (|β2|P)−1/2. In addition, the broadening, which is proportional to the soliton number37 N (P/|β2|)−1/2 must be sufficient to overlap with the DW phase matched wavelength. For the two smaller waveguides, the efficiency rapidly increases with pump power, reaching record values in the 30–35%. For the larger waveguides, the efficiency does not increase as quickly, mostly limited by the larger spectral separation between pump and DW. Additionally, larger waveguides have a higher value of |β2| at the pump wavelength (0.32 and 0.4 fs2/μm, respectively, compared to 0.14 and 0.22 fs2/μm for the 1000 and 1050 nm wide waveguides). For a given pulse peak power and width, the soliton number is thus smaller46, limiting both the compression factor and the number of compression points before the end of the waveguide (see Supplementary Figure 1 for a numerical comparison between all the different waveguides). Therefore less power can be coupled to the DW. Nevertheless, CEs close to 20% are still experimentally measured. Interestingly, the CE for the two smaller waveguides starts decreasing beyond a coupled power of about 12 mW, a behavior confirmed by the simulations. Indeed, increasing the pump power up to our 20 mW maximum does not result in a significant increase in DW power (see Fig. 4b). This could be due to the low values of |β2| in these waveguides, leading to a longer compression point than in the two larger waveguides (see Supplementary Note 1). Therefore, in narrower waveguides, spectral broadening caused by modulation instability46 can happen on the same length scale of soliton compression, already for coupled pump powers in the 12–20 mW range. In fact, at a given point on the waveguide, modulation instability scales exponentially with the pump power43. Equivalently, one can look at the soliton number, which also increases when |β2| decreases. Indeed, it has been shown that soliton fission occurs earlier than wave breaking by modulation instability35 when N < 10.

Fig. 4

Dispersive wave efficiency. Scattered points represent experimental data, lines are simulations. a mid-IR DW generation on-chip conversion efficiency (CE) as a function of coupled pump power. Error bars of ±0.5 dBm and ±0.25 dBm represent the standard deviation of repeated measurements of DW and coupled pump powers, respectively. b On-chip mid-IR DW power estimated from measured spectra. Error bars: same as for (a). 4.5 mW of on-chip DW power is reached at 3050 nm with 13 mW pump power, at 3220 nm with 16 mW of pump power, at 3530 nm with 22 mW of pump power, and 3950 nm with 26 mW of pump power

In Fig. 4b, we report numerical and experimental data of the mid-IR DW power as a function of the coupled pump power. In the employed pump power range, all waveguides can generate mid-IR DW with at least 4.5 mW but, due to the lower CE, the required pump power increases with the wavelength reach. However, thanks to the lower in-coupling losses, we could inject more power in the two larger waveguides and reach stronger DW generation at longer wavelengths. In fact, in such samples, the CE increases all over the tested power range, as N > 10 is expected for coupled power beyond 40 mW. Overall, this means that more than 1 mW can be estimated at the waveguides output (see Methods), covering the entire 3–4 μm spectral region.

We could also experimentally estimate the visible DW contribution by changing the output objective with a silica lens and the long pass filter with a short pass one with cut-off at 700 nm. While this configuration leads to larger uncertainties in the measurements, mainly due to larger scattering losses at shorter wavelengths, both simulations and experimental data confirmed the much lower CE for the visible DW generation, which remained well below 5%.

Proof-of-principle spectroscopy measurement of C2H2

To demonstrate the application of our on-chip source, we preformed mid-IR absorption spectroscopy of acetylene (C2H2) using the DW near 3 μm from the 1000 nm wide waveguide (see Methods for additional information on the employed experimental set-up). The light from the Si3N4 waveguide is directly coupled into a 108.5 cm long gas cell, which contained the sample or reference gas. The transmitted spectra measured with an optical spectrum analyzer (OSA) after the cell, with and without sample C2H2 gas, are shown in Fig. 5a. Absorption dips originating from C2H2 in the gas cell and from atmospheric gas (H2O) outside the cell are clearly seen. Figure 5b, c shows the normalized absorption spectrum of C2H2 compared to the one simulated utilizing the HITRAN database47. The standard deviation of residual absorbance for this global fit is ~2.5 × 10−4 cm−1. The maximum absorbance for 396 ppm C2H2 was measured to be 8.8 × 10−3 cm−1. The signal-to-noise ratio was calculated to be 35 and the noise equivalent concentration is ~11 ppm. Clear spikes in the residuals near the absorption peaks are likely due to the wavelength nonlinearity of the OSA within the detection range, which is not taken into account in the model.

Fig. 5

Mid infrared gas spectroscopy. a Transmitted spectrum of the empty (light blue) or filled (dark blue) gas cell with C2H2 in N2 buffer gas at 1 atm total pressure. b Observed absorbance (dark blue) with the gas cell filled with C2H2 in N2 buffer gas by normalizing the sample spectrum to that of the pure N2 reference gas in the cell, theoretical absorbance (HITRAN) (in red and inverted for clarity), and the residuals (green), differences between simulations and experimental data, of the multiple-line fit. c Zoom on the observed and HITRAN absorbance


We showed that the generation efficiency of mid-IR DW from a commercial femtosecond SWIR fiber laser can be greatly enhanced to more than 35%, by proper dispersion engineering of Si3N4 waveguides. In fact, state-of-the-art fabrication techniques and fiber laser technology allow for careful waveguide design which, in combination with a proper choice of the pump parameters, significantly favor the generation of mid-IR DW and reduce the visible one, allowing us to report the highest efficiency measured to date for on-chip mid-IR DW generation. The central wavelength of the DWs increases with the width of the waveguide and can be precisely positioned inside the first mid-IR transparency window while maintaining preferential power transfer to the mid-IR. Although the efficiency decreases with increasing DW wavelength, we were able to obtain, at the chip output, a maximum average output power of more than 1 mW spanning roughly the entire 3–4 μm region. These values represent a significant improvement both in terms of spectral coverage and efficiency, compared to previous mid-IR SCG34. Notably, the mid-IR output energy we obtained is comparable to the state-of-the-art mid-IR sources for dual-comb spectroscopy, based on DFG in PPLN waveguides13, pumped with similar peak power fiber frequency combs. The source can be used for absorption spectroscopy, as shown here with the detection of C2H2 in the 3 μm band. The expected comb structure of the DW34 could also enable dual-comb measurements, which however would be best implemented pumping the waveguides using a laser with hundreds of MHz of repetition rate8.

In summary, the presented approach can lead to a very efficient, compact, and easy to use device for coherent mid-IR light generation. In fact, it benefits from photonic integration both for the chip-scale nonlinear stage, compatible with planar fabrication techniques, and for the pump source which is a silica fiber-based laser. The device can cover the 3–4 μm region, which hosts the signature of important greenhouse gases like methane (CH4) and nitrous oxide (N2O). The absorption lines of carbon dioxide (CO2), just at the boundaries of the covered range (around 2.7 and 4.3 μm), can be targeted with slightly narrower or wider waveguides. In addition, this approach provides a power level sufficient for spectroscopy application13, bridging the gap between fiber sources and quantum cascade lasers, which are the workhorse of mid-IR spectroscopy devices. Such result could therefore provide a suitable alternative to microresonators48,49,50,51,52 to generate mid-IR frequency combs on a chip, when sub-gigahertz teeth spacing is required. Moreover, soliton-induced SCG in integrated photonic platforms has been recently demonstrated to coherently broaden the spectrum of optical frequency combs by more than one octave53, allowing their stabilization in f-to-2f schemes54,55. Therefore, with the possibility to combine both χ(2) and χ(3) nonlinearities in Si3N456,57,58, full on-chip stabilization of the mid-IR comb generated in these waveguides can also be considered.


Numerical simulations

The waveguide dispersion was simulated using a Finite Element Method software (COMSOL Multiphysics) in which the wavelength dependence of the real part of the refractive index of Si3N4 and SiO2 were included using the Sellmeier equation reported in refs. 48,59 respectively. In Fig. 1b, we include the imaginary part of the refractive index of SiO2 as k = 5·10−(9+λ), which qualitatively reproduces, in the region from 1 to 5 μm, the data reported in ref. 60. The SCG was simulated based on the nonlinear Schrödinger equation. We consider an input sech2 pulse with a frequency chirp of −1000 fs2/2π, leading to pulse duration of about 110 fs. The laser temporal pulse broadening mainly comes from the dispersion in the wave-plates and input objective. We included the spectral dependence of the nonlinear coefficient and a full and complete dispersion profile that comprises up to 30th order when Taylor expended with respect to the pumping frequency. Including more than 30 HOD terms does not change the simulation result but just slowed down the computation. We also set the Raman fraction and linear propagation losses to 0. In order to better compare with the experimental results, we included a nonlinear contribution in the experimental in-coupling losses proportional to the coupled pump power to the third power. We attribute the need of this correction to the increase of multiphoton absorption processes and the consequent free carrier absorption, mainly coming from the increase of visible DW and the generated third harmonic with the pump power.

Waveguide fabrication

The waveguides under test are fabricated accordingly to the photonic damascene process36, which consists of a conformal low pressure chemical vapor deposition (LPCVD) of Si3N4. In addition to the waveguides, a dense filler pattern is patterned into the hard mask of amorphous silicon on a 4 μm thick wet thermal silicon dioxide. This pattern efficiently releases the tensile stress and prevents cracking of the thick Si3N4 thin film. The Si3N4 core channels are covered by a cladding of low temperature oxide (LTO).

Dispersive wave generation efficiency

We estimate the DW power by integration on the FT-OSA. To first calibrate the power measurement in the FT-OSA, we directly coupled the attenuated pump laser at 2090 nm to the MMF via the parabolic mirror and sent it to the spectrometer. We measured the value obtained integrating the entire laser bandwidth in the FT-OSA (PFT-OSA) and we compared it to the power detected with an InGaAs photodiode (Thorlabs S148C) at the output of the MMF (PPD). The quantity c = PPD/PFT-OSA gave us the calibration factor for the spectrometer. The mid-IR DWs were then integrated over their entire spectral extend, namely 86–113, 80–110, 76–105, and 70–90 THz for the 1000, 1050, 1100, and 1175 nm wide waveguides, respectively. These values were then multiplied by the measured calibration factor (c) at the pump wavelength to retrieve the mid-IR DW power at the MMF output. It is important to notice that c is constant over the entire FT-OSA spectral range. Finally, we considered the total out-coupling losses, including transmission through the MMF and the output lens, which was optimized for mid-IR throughput. The on-chip CE is then calculated as the ratio between the on-chip mid-IR DW power over the coupled pump power. The coupled pump power is estimated by direct detection of the pump laser before the chip, and taking into account the in-coupling losses from the input lens (5 dB).

Also, we simulated the CE by integrating the output spectra obtained solving the nonlinear Schrödinger equation. The CE was defined as the ratio between the integral performed over the DW bandwidth, over the integral of the input spectrum. The on-chip power was then calculated by multiplying the theoretical CE by the value of the pump power used in the simulation.

Absorption spectroscopy

The mid-IR DW is collimated by adjusting the focal distance of the objective at the chip output and passes through the cell. The sample spectrum is obtained by filling the gas cell with 396 ppm C2H2 buffered in N2 in 1 atm total pressure at T = 296 K. The reference is obtained by purging the cell with pure N2. The measurement time is ~2 min. The light exiting the gas cell is guided to an OSA (Yokogawa AQ6376) through a single mode indium fluoride (InF3) fiber to improve spectral resolution. In this configuration, the total losses from the chip output are estimated to be around 20 dB. The OSA was set to its best resolution, corresponding to 0.1 nm with a single mode fiber, and high sensitivity setting using the internal chopper mode. We used 0.1 sampling interval for Fig. 5a and 0.02 for Fig. 5b, c.

Data availability

The data that support the findings of this study are available from the corresponding authors on reasonable request.


  1. 1.

    Keilmann, F., Gohle, C. & Holzwarth, R. Time-domain mid-infrared frequency-comb spectrometer. Opt. Lett. 29, 1542–1544 (2004).

    ADS  Article  Google Scholar 

  2. 2.

    Petersen, C. R. et al. Mid-IR supercontinuum covering the 1.4 μm to 13.3 μm molecular fingerprint region using ultra-high NA chalcogenide step-index fibre. Nat. Photonics 8, 830–834 (2014).

    ADS  CAS  Article  Google Scholar 

  3. 3.

    Vainio, M. & Halonen, L. Mid-infrared optical parametric oscillators and frequency combs for molecular spectroscopy. Phys. Chem. Chem. Phys. 18, 4266–4294 (2016).

    CAS  Article  Google Scholar 

  4. 4.

    Razeghi, M., Bandyopadhyay, N., Bai, Y., Lu, Q. & Slivken, S. Recent advances in mid infrared (3–5 µm) quantum cascade lasers. Opt. Mater. Express 3, 1872–1884 (2013).

    ADS  Article  Google Scholar 

  5. 5.

    Vurgaftman, I. et al. Mid-infrared interband cascade lasers operating at ambient temperatures. New J. Phys. 11, 125015 (2009).

    ADS  Article  Google Scholar 

  6. 6.

    Kozlovskii, V. I. et al. Pulsed Fe2+:ZnS laser continuously tunable in the wavelength range of 3.49–4.65 μm. Quantum Electron. 41, 1–3 (2011).

    ADS  Article  Google Scholar 

  7. 7.

    Muraviev, A. V., Smolski, V. O., Loparo, Z. E. & Vodopyanov, K. L. Massively parallel sensing of trace molecules and their isotopologues with broadband subharmonic mid-infrared frequency combs. Nat. Photonics 12, 209–214 (2018).

    ADS  CAS  Article  Google Scholar 

  8. 8.

    Lee, K. F. et al. Midinfrared frequency comb from self-stable degenerate GaAs optical parametric oscillator. Opt. Express 23, 26596–26603 (2015).

    ADS  CAS  Article  Google Scholar 

  9. 9.

    Cruz, F. C. et al. Mid-infrared optical frequency combs based on difference frequency generation for molecular spectroscopy. Opt. Express 23, 26814–26824 (2015).

    ADS  CAS  Article  Google Scholar 

  10. 10.

    Ruehl, A. et al. Widely-tunable mid-infrared frequency comb source based on difference frequency generation. Opt. Lett. 37, 2232–2234 (2012).

    ADS  CAS  Article  Google Scholar 

  11. 11.

    Erny, C. et al. Mid-infrared difference-frequency generation of ultrashort pulses tunable between 3.2 and 4.8 μm from a compact fiber source. Opt. Lett. 32, 1138–1140 (2007).

    ADS  CAS  Article  Google Scholar 

  12. 12.

    Soboń, G., Martynkien, T., Mergo, P., Rutkowski, L. & Foltynowicz, A. High-power frequency comb source tunable from 2.7 to 4.2 μm based on difference frequency generation pumped by an Yb-doped fiber laser. Opt. Lett. 42, 1748–1751 (2017).

    ADS  Article  Google Scholar 

  13. 13.

    Ycas, G. et al. High-coherence mid-infrared dual-comb spectroscopy spanning 2.6 to 5.2 μm. Nat. Photonics 12, 202–208 (2018).

    ADS  CAS  Article  Google Scholar 

  14. 14.

    Xing, S. et al. Mid-infrared continuous-wave parametric amplification in chalcogenide microstructured fibers. Optica 4, 643–648 (2017).

    Article  Google Scholar 

  15. 15.

    Hudson, D. D. et al. Toward all-fiber supercontinuum spanning the mid-infrared. Optica 4, 1163–1166 (2017).

    CAS  Article  Google Scholar 

  16. 16.

    Granzow, N. et al. Mid-infrared supercontinuum generation in As2S3-silica “nano-spike” step-index waveguide. Opt. Express 21, 10969–10977 (2013).

    ADS  CAS  Article  Google Scholar 

  17. 17.

    Lee, K. F. et al. Midinfrared frequency combs from coherent supercontinuum in chalcogenide and optical parametric oscillation. Opt. Lett. 39, 2056–2059 (2014).

    ADS  CAS  Article  Google Scholar 

  18. 18.

    Marandi, A. et al. Mid-infrared supercontinuum generation in tapered chalcogenide fiber for producing octave-spanning frequency comb around 3 μm. Opt. Express 20, 24218–24225 (2012).

    ADS  CAS  Article  Google Scholar 

  19. 19.

    Rudy, C. W., Marandi, A., Vodopyanov, K. L. & Byer, R. L. Octave-spanning supercontinuum generation in in situ tapered As2S3 fiber pumped by a thulium-doped fiber laser. Opt. Lett. 38, 2865–2868 (2013).

    ADS  CAS  Article  Google Scholar 

  20. 20.

    Yu, Y. et al. Mid-infrared supercontinuum generation in chalcogenides. Opt. Mater. Express 3, 1075–1086 (2013).

    ADS  Article  Google Scholar 

  21. 21.

    Gauthier, J.-C. et al. Mid-IR supercontinuum from 2.4 to 5.4 μm in a low-loss fluoroindate fiber. Opt. Lett. 41, 1756–1759 (2016).

    ADS  CAS  Article  Google Scholar 

  22. 22.

    Salem, R. et al. Mid-infrared supercontinuum generation spanning 1.8 octaves using step-index indium fluoride fiber pumped by a femtosecond fiber laser near 2 µm. Opt. Express 23, 30592–30602 (2015).

    ADS  CAS  Article  Google Scholar 

  23. 23.

    Domachuk, P. et al. Over 4000 nm bandwidth of mid-IR supercontinuum generation in sub-centimeter segments of highly nonlinear tellurite PCFs. Opt. Express 16, 7161–7168 (2008).

    ADS  CAS  Article  Google Scholar 

  24. 24.

    Hickstein, D. D. et al. Ultrabroadband supercontinuum generation and frequency-comb stabilization using on-chip waveguides with both cubic and quadratic nonlinearities. Phys. Rev. Appl. 8, 014025 (2017).

    ADS  Article  Google Scholar 

  25. 25.

    Lau, R. K. W. et al. Octave-spanning mid-infrared supercontinuum generation in silicon nanowaveguides. Opt. Lett. 39, 4518–4521 (2014).

    ADS  CAS  Article  Google Scholar 

  26. 26.

    Kuyken, B. et al. An octave-spanning mid-infrared frequency comb generated in a silicon nanophotonic wire waveguide. Nat. Commun. 6, 6310 (2015).

    CAS  Article  Google Scholar 

  27. 27.

    Liu, X. et al. Octave-spanning supercontinuum generation in a silicon-rich nitride waveguide. Opt. Lett. 41, 2719–2722 (2016).

    ADS  CAS  Article  Google Scholar 

  28. 28.

    Porcel, M. A. G. et al. Two-octave spanning supercontinuum generation in stoichiometric silicon nitride waveguides pumped at telecom wavelengths. Opt. Express 25, 1542–1554 (2017).

    ADS  CAS  Article  Google Scholar 

  29. 29.

    Chávez Boggio, J. M. et al. Dispersion-optimized multicladding silicon nitride waveguides for nonlinear frequency generation from ultraviolet to mid-infrared. J. Opt. Soc. Am. B 33, 2402–2413 (2016).

    ADS  Article  Google Scholar 

  30. 30.

    Sinobad, M. et al. Mid-infrared octave spanning supercontinuum generation to 8.5 μm in silicon–germanium waveguides. Optica 5, 360–366 (2018).

    Article  Google Scholar 

  31. 31.

    Singh, N. et al. Midinfrared supercontinuum generation from 2 to 6 μm in a silicon nanowire. Optica 2, 797–802 (2015).

    CAS  Article  Google Scholar 

  32. 32.

    Nader, N. et al. Versatile silicon-waveguide supercontinuum for coherent mid-infrared spectroscopy. APL Photonics 3, 036102 (2018).

    ADS  Article  Google Scholar 

  33. 33.

    Kowligy, A. S. et al. Mid-infrared frequency comb generation via cascaded quadratic nonlinearities in quasi-phase-matched waveguides. Opt. Lett. 43, 1678–1681 (2018).

    ADS  CAS  Article  Google Scholar 

  34. 34.

    Guo, H. et al. Mid-infrared frequency comb via coherent dispersive wave generation in silicon nitride nanophotonic waveguides. Nat. Photonics 12, 330–335 (2018).

    ADS  CAS  Article  Google Scholar 

  35. 35.

    Dudley, J. M., Genty, G. & Coen, S. Supercontinuum generation in photonic crystal fiber. Rev. Mod. Phys. 78, 1135–1184 (2006).

    ADS  CAS  Article  Google Scholar 

  36. 36.

    Pfeiffer, M. H. P. et al. Photonic Damascene process for integrated high-Q microresonator based nonlinear photonics. Optica 3, 20–25 (2016).

    CAS  Article  Google Scholar 

  37. 37.

    Chen, C.-M. & Kelley, P. L. Nonlinear pulse compression in optical fibers: scaling laws and numerical analysis. J. Opt. Soc. Am. B 19, 1961–1967 (2002).

    ADS  CAS  Article  Google Scholar 

  38. 38.

    Akhmediev, N. & Karlsson, M. Cherenkov radiation emitted by solitons in optical fibers. Phys. Rev. A 51, 2602–2607 (1995).

    ADS  CAS  Article  Google Scholar 

  39. 39.

    Karpov, M. et al. Raman self-frequency shift of dissipative Kerr solitons in an optical microresonator. Phys. Rev. Lett. 116, 103902 (2016).

    ADS  Article  Google Scholar 

  40. 40.

    Roy, S., Bhadra, S. K. & Agrawal, G. P. Effects of higher-order dispersion on resonant dispersive waves emitted by solitons. Opt. Lett. 34, 2072–2074 (2009).

    ADS  Article  Google Scholar 

  41. 41.

    Roy, S., Bhadra, S. K. & Agrawal, G. P. Dispersive waves emitted by solitons perturbed by third-order dispersion inside optical fibers. Phys. Rev. A 79, 023824 (2009).

    ADS  Article  Google Scholar 

  42. 42.

    Zhang, L. et al. Silicon waveguide with four zero-dispersion wavelengths and its application in on-chip octave-spanning supercontinuum generation. Opt. Express 20, 1685–1690 (2012).

    ADS  CAS  Article  Google Scholar 

  43. 43.

    Agrawal, G. P. Nonlinear Fiber Optics (Elsevier, Oxford 2013).

  44. 44.

    Gorbach, A. V. & Skryabin, D. V. Light trapping in gravity-like potentials and expansion of supercontinuum spectra in photonic-crystal fibres. Nat. Photonics 1, 653–657 (2007).

    ADS  CAS  Article  Google Scholar 

  45. 45.

    Wang, W., Yang, H., Tang, P., Zhao, C. & Gao, J. Soliton trapping of dispersive waves in photonic crystal fiber with two zero dispersive wavelengths. Opt. Express 21, 11215–11226 (2013).

    ADS  Article  Google Scholar 

  46. 46.

    Kutz, J. N., Lyngå, C. & Eggleton, B. J. Enhanced supercontinuum generation through dispersion-management. Opt. Express 13, 3989–3998 (2005).

    ADS  Article  Google Scholar 

  47. 47.

    Rothman, L. S. et al. The HITRAN2012 molecular spectroscopic database. J. Quant. Spectrosc. Radiat. Transf. 130, 4–50 (2013).

    ADS  CAS  Article  Google Scholar 

  48. 48.

    Luke, K., Okawachi, Y., Lamont, M. R. E., Gaeta, A. L. & Lipson, M. Broadband mid-infrared frequency comb generation in a Si3N4 microresonator. Opt. Lett. 40, 4823–4826 (2015).

    ADS  CAS  Article  Google Scholar 

  49. 49.

    Griffith, A. G. et al. Silicon-chip mid-infrared frequency comb generation. Nat. Commun. 6, 6299 (2015).

    CAS  Article  Google Scholar 

  50. 50.

    Wang, C. Y. et al. Mid-infrared optical frequency combs at 2.5 μm based on crystalline microresonators. Nat. Commun. 4, 1345 (2013).

    CAS  Article  Google Scholar 

  51. 51.

    Yu, M., Okawachi, Y., Griffith, A. G., Lipson, M. & Gaeta, A. L. Modelocked mid-infrared frequency combs in a silicon microresonator. Optica 3, 854–860 (2016).

    CAS  Article  Google Scholar 

  52. 52.

    Yu, M. et al. Silicon-chip-based mid-infrared dual-comb spectroscopy. Nat. Commun. 9, 1869 (2018).

    ADS  Article  Google Scholar 

  53. 53.

    Johnson, A. R. et al. Octave-spanning coherent supercontinuum generation in a silicon nitride waveguide. Opt. Lett. 40, 5117–5120 (2015).

    ADS  CAS  Article  Google Scholar 

  54. 54.

    Klenner, A. et al. Gigahertz frequency comb offset stabilization based on supercontinuum generation in silicon nitride waveguides. Opt. Express 24, 11043–11053 (2016).

    ADS  CAS  Article  Google Scholar 

  55. 55.

    Mayer, A. S. et al. Frequency comb offset detection using supercontinuum generation in silicon nitride waveguides. Opt. Express 23, 15440–15451 (2015).

    ADS  CAS  Article  Google Scholar 

  56. 56.

    Grassani, D., Pfeiffer, M. H. P., Kippenberg, T. J. & Brès, C.-S. Second- and third-order nonlinear wavelength conversion in an all-optically poled Si3N4 waveguide. Opt. Lett. 44, 106–109 (2019).

    ADS  Article  Google Scholar 

  57. 57.

    Billat, A. et al. Large second harmonic generation enhancement in Si3N4 waveguides by all-optically induced quasi-phase-matching. Nat. Commun. 8, 1016 (2017).

    ADS  Article  Google Scholar 

  58. 58.

    Porcel, M. A. G., Mak, J., Taballione, C., van der Slot, P. J. M. & Boller, K.-J. Photo-induced second-order nonlinearity in stoichiometric silicon nitride waveguides. Opt. Express 25, 33143–33159 (2017).

    ADS  CAS  Article  Google Scholar 

  59. 59.

    Malitson, I. H. Interspecimen comparison of the refractive index of fused silica. J. Opt. Soc. Am. 55, 1205 (1965).

    ADS  CAS  Article  Google Scholar 

  60. 60.

    Kitamura, R., Pilon, L. & Jonasz, M. Optical constants of silica glass from extreme ultraviolet to far infrared at near room temperature. Appl. Opt. 46, 8118–8133 (2007).

    ADS  CAS  Article  Google Scholar 

Download references


D.G., E.T., and C.-S.B. acknowledge support by the European Research Council (ERC) under grant agreement ERC-2012-StG 306630-MATISSE and ERC-2017-CoG 771647-PISSARRO. C.H., H.G., and T.J.K. acknowledge support by contract W31P4Q-16-1-0002 (SCOUT) from the Defense Advanced Research Projects Agency (DARPA), Defense Sciences Office (DSO), and support by the Swiss National Science Foundation under grant agreement no. 161573; H.G. acknowledges funding from the European Union’s Horizon 2020 research and innovation program under Marie Sklodowska-Curie IF grant (No. 709249); F.Y. acknowledges support by the Swiss National Science Foundation under grant agreement no. 178895. The authors acknowledge Prof. Luc Thévenaz for fruitful discussions.

Author information




D.G. performed the simulations, and D.G. and E.T. performed the experiments under the supervision of C.-S.B. H.G. and C.H. conceived the design of large cross-section Si3N4 waveguides under the supervision of T.J.K. C.H. fabricated the large cross-section waveguides. F.Y., E.T., and D.G. performed the gas absorption experiment and F.Y. performed the HITRAN simulation. All authors discussed the data. D.G. and E.T. wrote the manuscript with input from others. C.-S.B. supervised the project.

Corresponding authors

Correspondence to Davide Grassani or Camille-Sophie Brès.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Journal peer review information: Nature Communications thanks Andrew Metcalf and the other anonymous reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Grassani, D., Tagkoudi, E., Guo, H. et al. Mid infrared gas spectroscopy using efficient fiber laser driven photonic chip-based supercontinuum. Nat Commun 10, 1553 (2019).

Download citation

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing